Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
1 +, 1 +
01 ' 5
The Right to Information, The Right to Live
Step Out From the Old to the New
Mazdoor Kisan Shakti Sangathan
Jawaharlal Nehru
IS 1542 (1992): sand for plaster [CED 5: Flooring, Wall
Finishing and Roofing]
! $ ' +-
Satyanarayan Gangaram Pitroda
Invent a New India Using Knowledge
! > 0 B
BharthariNtiatakam
Knowledge is such a treasure which cannot be stolen
( Reaffirmed 2003 )
Indian Standard
SAND FOR PLASTER - SECIFICATION
/ Second Revision J
Second Reprint FEBRUARY 1999
UDC 691.223:691.55
@ BIS 1992
BUREAU
MANAK
OF INDIAN
BHAVAN,
9 BAHADUR
STANDARDS
SHAH ZAFAR
MARC3
NEW DELHI 110002
J&J 1992
Wcibql
Flooring, Wall Finishing and Roofing Sectional Committee, CED 5
FOREWORD
This Indian Standard ( Second Revision ) was adopted by the Bureau of Indian Standards, after the
draft finalized by the Flooring, Wall Finishing and Roofing Sectional Committee had been approved
by the Civil Engineering Division Council.
This standard was first published in 1960 and subsequently revised in 1977. In this second revision
following major modifications are made :
a) Crushed gravel sand and ALPM have been added in the scope and pit sand has been included
under naturally occurring sands;
b) As per the grading given in Table 1, the fineness modulus of sand could vary from I.2 to 2.2.
However, it is preferable to have minimum fineness modulus of l-4 in case of crushed stone
sands and crushed gravel sands and a F. M of 1 5 in case of naturally occurring sands. Hence,
this new clause, namely 5.2 has been added;
c) Amendment No. 1 giving O-15 percent passing for 150 micron IS Sieve in Table 1 has been
incorporated;
d) A new clause, namely 7.1 (a) has been added so that when requested by the purchaser, the
supplier shall supply particle size grading of sand.
For the purpose of deciding whether a particular requirement of this standard is complied with, the
final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in
accordance with IS 2 : 1960 Rules for rounding off numerical values ( revised ). The number of
significant places retained in the rounded off value should be the same as that of the specified value in
this standard.
IS x42:1992
Indian Standard
SAND FOR PLASTER -
SPECIFICATION
( Second Revision J
1 SCOPE
3.4 Crushed Stone Sand and Crashed Gravel Sand
1.1 This standard covers the requirements of
naturally occurring sands, crushed stone sands
and crushed gravel sands used in mortars for
internal wall and ceiling plastering, and external
plastering using mixes of lime, cement, compoactivated
lime pozzolana
site lime-cement,
mixture ( ALMP ) or gypsum with or without
admixtures and sand.
A fine
aggregate produced
stone or natural gravel.
IS No.
383 : 1970
1727 : 1967
2250 : 1981
2386
( Part 1 ) : 1963
( Part 2 ) : 1963
( Part 3 ) : 1963
2430 : 1986
hard
4 QUALITY OF SAND
4.1 General
The sand shall consist of natural sand, crushed
stone sand or crushed gravel sand or a combination of any of these. The sand shall be hard,
durable, clean and free from adherent coatings
and organic matter and shall not contain clay,
silt and dust more than specified under 4.3 (a).
2 REFERENCES
2.1 The following Indian Standards
sary adjuncts to this standard.
by crushing
are neces-
4.2 Deterious Materials
Title
The sand shall not contain any harmful impurrties, such as, iron pyrites, alkalis, salts, coal,
mica, shale or similar laminated materials, soft
fragments, sea shells and organic impurities in
such quantities
as to affect adversely
the
hardening, the strength, the durability of the
appearance of the plaster or applies decoration,
or to cause corrosion of metal lathing or other
metal in contact with the plaster.
Specification for coarse and
fine aggregates from natural
sources for concrete ( second
revision )
Method of test for pozzolanic
materials (first revision )
Code of practice for preparation and use of masonry
mortars (jirst revision )
Methods of test for aggregates for concrete :
Part 1 Particle size and shape
Part 2 Estimation of deleterious materials and organic
impurities
Part 3 Specific gravity, density, voids, absorption
and
bulking
Methods
for
sampling of
aggregates for concrete
4.3 Limits of Deleterious Materials
Unless found satisfactory as a result of further
tests as may be specified by the engineer or
architect, or unless evidence of such performance is offered which is satisfactory
to him,
the maximum quantities of clay, fine silt, fine
dust and organic impurities in the sand shall not
exceed the following limits:
a) Clay, silt and dust Not more
than
[ determined
in percent by weight
accordance
with
IS 2386 ( Part 2 ) :
1963 ]
3 TERMINOLOGY
3.1 For the purpose of this standard, the following definitions shall apply.
b) Organic impuriries
[ determined
in
accordance
with
IS 2386 ( Part 2 ) :
1963 ]
3.2 Sand
A fine aggregate which is either a natural sand,
crushed stone sand or crushed gravel sand.
3.3 Natural Sand
Colour
of
liquid
below that indicated
by comparison with
the standard solution
specified in 6.2.2 of
IS 2336 ( Part 2 ) :
1963
NOTE - In particular cases crushed stone sand with
even higher proportions
of fine dust than specified
above, may be satisfactory
and the limit so permitted
may be subject to the agreement between the suppliel
anti the purchaser.
A fine aggregate produced by the natural disintegration of rock which has been deposited by
streams or glacial agencies or obtained from
pits.
1
X31542:1992
4.4The average compressive strength,
determined by the standard
procedure
detailed in
Appendix A of IS 2250 : 1981, of mortar cubes
composed of one part of cement and six parts
of sand conforming to gradation in Table 1
shall be not less than 3 N/mm2 at 28 days.
6 SAMPLING AND TESTING
6.1 Sampling
The method of sampling shall be in accordance
with IS 2430 : 1986. The amount of material
required for each test shall be as specified in
relevant parts of IS 2386 and as per the requirements of 4.4.
4.4.1 The amount of water for gauging shall be
that required to give a flow between 110 to 115
with 25 drops in 15 seconds, as determined
in
9.5.3 of IS 1727 : 1967.
6.2 Testing
5 GRADING OF SAND
Any test which the purchaser or his representative may require in connection
with this
standard shall be carried out in accordance with
the provisions of various clauses in the standard.
Unless otherwise stated in the enquiry or order,
duplicate tests shall be made to al1 cases and
the results of both tests reported.
5.1 The particle size grading of sand for plaster
work for internal as well as external walls and
ceiling as analyzed by the method described in
IS 2386 ( Part 1 ) : 1973 shall be as specified in
Table 1. Where the grading falls outside the
limits of the grading zones of sieves other than
150, 300 and 600 micron IS Sieve by a total
amount not exceeding 5 percent, it shall be
regarded as falling within the grading.
7 ADDITIONAL INFORMATION TO BE
FURNISHED BY THE SUPPLIER
Table 1 Grading of Saod for Internal Wall or
External Wall or Ceiling Plaster
( C/awe 5.1 )
16 Sieve Designation
( See IS 460 : 1985)
1Omm
475 mm
236 mm
118 mm
600 micron
300 micron
150 micron
Percentage
7.1 When requested by the purchaser or his
representative,
the supplier shall provide the
following additional particulars:
Passiog
100
95-100
95-100
Source of supply - Precise locality
where the materials were obtained,
the name of the quarry or pit;
from
with
b) Trade
group of principal rock type in case
of manufactured
sand ( see Appendix C
of IS 383 : 1970 ); and
90-100
80-100
20-65
o-15
4 Particle size of grading when determined
ip96;ccordance
NOTE - For crushed stone sands and crushed gravel
sands, the permissible limit on 150 micron IS Sieve is
increased
to 20 percent. This does not affect the
5 percent allowance permitted in 5.1.
with IS 2386 ( Part I ) :
7.2 Subject to prior agreement, the supplier
shall furnish the following additional information, when required by the purchaser or his
representative:
5.2 The fineness modulus of sand shall be not
less than I.4 in case of crushed stone sands and
crushed gravel sands and not less than I.5 in
case of naturally occurring sands.
a) Specific gravity of sand [ determined
IS 2386 ( Part 3 ) : 1963); and
5.3 The various sizes of particles of which the
sand is composed shall be uniformly distributed
throughout the mass.
with
b) Bulk density [ determined in accordance
with IS 2386 ( Part 3 ) : 1963 1.
5.4 The required grading may often be obtained
by screening and/or by blending together either
natutal sands or crushed stone screenings, which
are by themselves of unsuitable grading.
7.3 If possible, information
on the bulking of
the sand with varying moisture content may be
furnished in the form of a graph.
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian StandardsAct, 1986 to promote
harmonious development of the activities of standardization, marking and quaIity_certification
of goods and
attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications.
No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sixes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publication), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the hasis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments,or edition by referring to the latest issue
of BIS Handbook and Standards Monthly Additions.
This Indian Standard has been developed
from Dot: No. CED 5 ( 4875 )
Amendments
Amend No.
Issued Since Publication
Date of Issue
BUREAU
Text Affected
OF INDIAN STANDARDS
Headquarters:
Manak Bhavan, 9 Bahadur Shah &far Marg, New Delhi 110002
Telephones: 323 0131,323 33 75,323 94 02
Telegrams: Manaksanstha
(Common to all offices)
Telephone
Regional Offices:
Central
: Manak Bhavan, 9 Bahadur Shah Zafar Marg
323 76 17,323 38 41
NEW DELHI 110002
Eastern
337 84 99,337 85 61
337 86 26,337 9120
: l/14 C.I.T. Scheme VII M, V.I.P. Road, Maniktola
CALCUTTA
700054
Northern
: SC0 335336,
Sector 34-A CHANDIGARH
Southern
: C.I.T. Campus, IV Cross Road, CHENNAI
Western
: Manakalaya,
Branches
: AHMADABAD.
60 38 43
{ 602025
160022
235 02 16,235 04 42
{ 235 15 19,235 23 15
600113
E9 MIDC, Marol, Andheri (East)
MUMBAI 400093
832 92 95,832
832 78 91,832
78 58
78 92
BANGALORE. BHOPAL. BHUBANESHWAR.
COIMBATORE.
FARIDABAD.
GHAZIABAD.
GUWAHATI.
HYDERABAD.
JAIPUR. KANPUR.
LUCKNOW.
NAGPUR.
PATNA.
PUNE. THIRUVANANTHAPURAM.
Printed by Reprography Unit, BIS, New Delhi
