Application of SFFECO Fire Pump: SFFECO ule ww Hose Rack Systems Hose Reel Systems Foam Systems Deluge Systems Hydrant Systems Protect Sprinkler Systems WOH r Tees TeSFFECO Fire Pump Packages = " a Model : EDJ (Electrical, Diesel & Jockey Pumps) SFFECO's EDJ EXCEL series is a packaged fire pump set. It ‘consists of a main pump (driven by an electrical motor), stand by puino (crven by dese! engine) and a jockey pump. This model comes equipped with a separate controller, or one that is attached to the skid, The package also contains discharge valves, common header, and accessories. Model : EJ (Electrical & Jockey Pumps) SFFECO's €J EXCEL series is @ packaged fire pump sel. It consists of a main pump (driven by an electrical motor) and a jockey pump. This model comes equipped with a separate controller, or one that is attached to the skid. The package also coniains discharge valves, common header, and accessories. Model : DJ (Diesel & Jockey Pumps) SFFECO's DJ EXCEL series is a packaged fire pump set. It consists of a main pump (driven by diesel engine) and a jockey pump. This mode! comes equipped with a separate controller, or one that is attached to the skid. The package also contains discharge valves, common header, and accessories.32-100mm Max1500 GPM Max100m, Working Pressure Max105°C Max 1 Mpa Suitable for Speed of Motor 3500 RPM- 60 Hz 2900 RPM- 50 Hz. Features: 2900 RPM Al single stage, suction, back exposed and centrifugal pumps have outline dimension and Structural drawing 4. Casing 2, Impeller 3. Shaft 4, Shafl Sleeve 5. Seal Ring 6, Casing Cover 7. Packing Gland 8, Bearing Bracket 40. Impeller Nut 12. Gasket 9. Support Feet 41. Mechanical Seal 18. Seal Gland Structure | gland structural dimension according to DIN 24255 standard, Pump Casing) HT 250 Shaft Seal | Mechanicl Seal aocordng to DIN 24960/gland packing Bearings | Sealed type bearing, pre-lubrication Shaft Sleeve | 2Cr13 | Shaft 20113, Sa 2 Connections | Standard NPT threaded ‘above 3" discharge : 125# ASA Flanges Impeller Casing Ring Casing Cover QT450-10 iT 250 ZcuAL10Fe3, OCr8Nig OCr7Ni12Mo2 HT250 ZCuSnSPbZn5 ANSI Design The ANSI standard adopted by NFPA 20 assures a ‘quality design to provide years of operation.(m) HEAD (m) HEAD 317, 49 89 80 100 189 200 300 400 600 8001200 1600 =2900r/mi 203 sOMaia MAaEO 20 30 40 5060 80 100 150 USGPM 400 300 200 150 100 80 60 50 40 30 20 a) FEET 200 (Us) 12720 30 40 60 80 100 150200 300 400 600 8001000: US.G.P-M 8=3500r/min 08 2 3 4 5 6 8 10 20° 30 405060 80 100120 Als) 400 300 200 150 100 80 60 40 30 20 18 10 (tty FEETPump Oimensions Pump Fast Dimensions te wa] of | 2] ei] a afi w 36072 [a0 70 | 190140] [100 EES 3 3a 132 [10 70 TO] Ta papas Be a 3a [reo [160 TO AO BO | LH BE Bo 3 ZO 3B Bo oe | BOLTS Ba [350 PE | TEL FO 1004 100 meas DY wo [a0 we [0 7 [ HO 180 || 700 2 3 ao Hoo | 900-00 [8 Te w5 a] [0 peas CEE [320-250] | wpe pale ao as | a7] 200 | 28 3 [ms | 260 16 [0 Po a0 00 | 360_| |e 70] a0 | 0] 4 [a0 zfs far Le 80) 10] 360 [780 [100 [70 [ass | 212 [ia [0 af | arf 8 301100] 360700 | 200 70 | 265 [21a | 0 za sofas 30 [0 | 960 [7a0 | 226 [as [e020 ia za sop ee 0 roo | asa [10 | 225, [35-320 [250 ia [0 apa] =o 20 ts 70725 | 260 [ss [60] [0 [oo 35 [0 5 [0] 350 | Tao [780 3 [200 aia [HO mPa pape 5 [oo | 360" 160 [200 [aa aia a [0 me 3 5 oo] 350] 780 | 205 [20 250] | msl ars 00 | aor [Tao | 28 125 [05 | 20 | 280 | 0 2] a [35 [0 @5 100 «70_| 200 | 280 120 360 | 250 7.8] 110 eo [0 5 | 125| «70 | 205 [280 60120 400 | 516 | 175 [0 aos D0 a0 25 | 360 Ta0 | 205 2 [woo [aa0 te [0 spare eo a5 | aoa [ 780 [205 [aad | |e [HO S| oo 350 eo a5 | 470 | | 2a & [35 | aa | te [HO 2a ss [0 a0 925 | 470 [20 [2a 720] 400 | 315 7S ze] [0 a0 125 | a0_[ 950 [315 125 400 | 315175] 110 eos 10 382 | 200 | 38 20 40 [340 17.5] 110 2 [10] 52 -70_| 20 | 250 120] 90 | 2e0| 175/10 35 | 10 70 235 | 200 120 400] 315 175] 110 25 [10 s20_| 225 | 200 120 400 [315] 175) 10 [12 a70_| 250 | 315 120 4o0_[ 315 175/10 35-10 530 260 355 160 500 | «0025 [10 a5-[12 a70_| 260 [316 29 400. [ 315] 175) 10 35 Lo‘ontal Split Case - Ma SFFECO Ho: O Performance: = Discharge ON 65 - 100 mm Capacity Q Max 1500 GPM Head H Max 120.m Working Pressure P Max 75°C Working Temperature T Mex 1.2 Mpa Suitable for Speed of Motor SON POEs 2900 RPM - 50 Hz, Suitable for Speed of Diesel Engine | 2900 RPM Features: Construction Alkiron construction with bronze internal fitings. Structure Horizontal Spit Case Design N Shaft Seal Mechanical Seal according to DIN 24960/packing gland aN Bearings Lubricated with grease. Ball bearings rc Casing Heavy Duty Cast Iron construction, / | The ANSI standard adopted by NFPA 20 assures a a ee ANSI Design ‘quality design to provide years of operation. Y Na / ‘Alloy steel, machined and ground to close Shaft ; tolerances. Shaft Sleeve B07 shaft sleeves are provided to protect the shaft Spit arewinn against wear and corrosion Casing Wear Bronze wear rings provide the sealing between the 1. Left Bearing Body 2. Seal Ring a — Po 3. Casing Cover 4. Impeller Lock Sleeve oN ee eee. 5. Impeller 6. Anti-flexible Impeller Key The double suction impellers are made of zincless 7. Seal Ring 8, Right Bearing Body bronze,and they have an enclosed design. The 9. Shaft 10. Motor Stoo) Impeller impellers are keyed to the shaft, and secured by adjustable shat sleeves. Allimpellers are dynamically balanced to ensure smooth operation. 11, Lantern Ring 12. Packing Gland 13. Casino o-ing 14. Casingom HEAD 288g 100 50 60 70 80 200-250 300 mith UScRM 600 500 400, 300 250 200 160 100 90 40 60 60 70 80 90100 160 US 160 200 250 200 500 =/h ay reeroa [2 |25 |e [30 [a [0 [en | [ie | 38 [20 [20 | [ao [au [0 [0 es os [7 [18 at 2 [2 [20 | 0 [30 [uo [0 [0 75 0 faze [20 ws 27 [ 2s | 20 [10 [20 70 [00 [20 78 2 [se [28 sis 298 | 368 | 310 [200 | 30 [20 [400 [340| 76 5 [ase [258 cue as [0 | [vo [0 [to [00 [0] 76 20 [8 [50 a ae [3 [20 [30 [to [eo [0 78 2 [96 [15 34 274 | 290 |275 | 150 | 300 [240 | 360 |200| 65 63 |150 |138 2 ao [20 [2s [7020 eo [0 es fos isJockey pump is used to maintain pressure of the system and thereby preventing the main fre pump from starting too frequently. Its rated capacity should not be less than the normal leakage rate. The shut off head should be approximately 10 psi greater than the main fire pump but should not exceed the system's design pressure. G-MAX PUMPS, U.K. Brand Type ~ | etic mutstage pup Pump head cover, shat, base, impel, outer sleeve, Construction and chamber are all made of stainless steel 304 or 316. Base plate & Pump head are made of Cast iron EN-GJL-200 Pressure Range Upto 225 bars Flow Capacity Upto 100 GPM Shaft Seal Single spring carbon rotary vs. ceramic statonary seat Orting for outersteeve | EPDM or FKM Rubber parts EPDM or KM Motor Protection Single phase motors havea builtin thermal ovrioad switch whereas te tree phase motors (3 KW and above) have a builtin thermostat PTC) cording to DIN 44082 ‘The motor is fully enclosed, fan-cooled, and includes 2-poles * Stainless Steel on request Motor with prnpal dimensions in accordance wih the EN standards. Electrical tolerances conform to EN 60034 Ambient naan Liquid-Stendard Design -15°C to +90°C Liquid- Hot Water = =45°C to +120°C Enclosure class IP 55 Insulation Class F Models: GVR / GVS 1 | Pump head Cast iron EN-GJL-200 2 | Pump head cover Stainless steel 304 3 | Shaft _ | Stainless steel 304 (or) ze 4) Base Stainless steel 304 (or) 316 5 | Shaft seal Mechanical 6 Base plate Cast iron EN-GJL-200 7 | Rubber parts EDPM or FKM. 8 Impeller Stainless steel 304 (or) 316 9 Chamber Stainless steel 304 (or) 316 10\ Outer sleeve Stainless steel 304 (or) 316 11 1g for outer sleeve EDPM or FKMMotor & Diesel Hitee design EIC Standards Model HM Series ae Made of aluminum and insulated by low-carbon magnetic steel laminations, Made of cathode copper and insulated low-carbon magnetic SEED slee! laminations. End Shields Cast Iron for both the drive end and non-drive end FanCover —Steelshest, aa Cooling Fan Protected by a cover with degree of protection IP 2x. . Fasteners Corrosion proof. =e : Protection 25. a Bs Electrical motor starts when the Voltage "Standard motors ere made for delta voltage of 380-415 with a écripieeareaagtinigs tena frequency of 50 Hz and a voltage of 220-240 or 380-460V at 60 Hz. ets | Shaft Superior grade steel with more torque absorbing capability. ~ ‘water flow in the system. ‘ aa Cast Iron- the body casting has longitudinal ribs, with integral | Horsepower rating feet for additional stability. Upto 270 HP "| Frequency "50/60 Hz Brand || The Hitec difference | and corrosion proof constru "Durable motor and components, trouble free performance low vibration design, silent functioning, easy maintenance, MEGAFORCE, UK. Diesel engine main parts and systems: Assembly Engine cylinder Block Engine block includes the crankshaft case and cylinders, in which ful-support main bearings are used. The assembly is made of alloy casting iron. Cylinder Head Assembly Cylinder heads a four-cylinder unit, made of alloy cast iron Crankshaft and Flywheel Assembly alloy steal wit four balance weights on the web. | Beating Main bearings are made of steel and high tn aluminum alloy Crankshaft is made of high strenght modular cas iron or assembly Diesel engine starts when the controller senses a power interruption during ‘operation or in the event of maintenance Transmission gear Piston and connecting rod The top of piston is designed to faciitate thermal flow, its skirt is of a variable oval barrel surface and with slipper ends, Connecting rods are made of forged steel. The timing on gear surface must be correctly sel when gears are assembled, in order to ensure corect er and fuel supply |The valve ttein of this engine is of an overhead type. Camshafts made of selected 45# steal on which three beering Ai Supply syst ‘on the main pump or duty pump. me ereen journals and eight cam lobes (al case-hardenedlare located. Cooling System Radiator Starting System lecte Starter Motor Exhaust System Flexible Exhaust System> SFFECO's mp Controlers are designed to control nd. monitor the “operation of the main, standby, and make up pumps for both manual and aut modes. The controller enables the diesel engine-driven pump to operate in case of power failure and substantial drop in pressure. A built in pressure switch detects any drop in pressure. The jockey pump controler initiates pumping when the designated water pressure in the system is lowered due to small leakages. SFFECO's controllers set is factory tested before shipment and is ready for immediate usage. SFFECO's control circuits for pumps can be customized to fit different requirement and needs. SFFECO's control panels undergo rigorous tests and quality procedures to ensure excellent performance. Enclosure Styles ® ration, signaling or monitoring systems ‘Automa Compatible wih ae lke BMS or FACE. Electronic Battery Chargen (Gurrent Sensing) Lamp Test Facility (Optione 2 Fault Trip Facility (other than dry fun - Optional). Crank protection circuit for diesel engine. Delayed star for Fire Signal (optional). Low pressure cut-off (timer based) (Optional). == Wall Mounted/Base Mounted, upto 250GPM(OOL) Electrical, Engine, Jockey (Seperate or Combined) | Model B Coa | Wall Mounted/Base Mounted, upto 750 GPM (DOL) Electrical, Engine, Jockey (Seperate or Combined) ir ola Self-standing, upto 1500 GPM (Star-Delta) Electrical, Engine, Jockey (Seperate or Combined) Model C Model D (Optional) Self-standing, upto 1000 GPM (Star-Delta) Electrical, Engine, Jockey (Combined Only) In line with our policy of continuous product improvement, we reserve the right to modify specifications without prior notice.SFFECO q SAUDI FACTORY FOR FIRE EQUIPMENT CO. Factory: 2nd Industrial Area - Al-Kharj Road - Riyadh Tel. 00966 12650070 - Fax. 00966 1 2652190 Sales Office: A\-Sitteen Street - Malaz - Riyadh Tel. 00966 1 2063294 - Fax. 00966 1 2063295 P.O. Box 58469 - E-mail : [email protected] Jeddah Branch _ : Tel. 00966 26706009 - Fax. 00966 2 6760307 Dammam Branch : Tel. 00966 3 8351961 - Fax. 00966 3 8351968 Madina Branch Tel. 00966 4 8660959 - Fax. 00966 4 8660969 Bahrain Branch: Telefax. 00973 17 721153 SFFECO INTERNATIONAL International Sales Office: Jebel Ali - Free Zone - Dubai - U. A. E Tel: 00971 4 883 0732 - Fax: 00971 4 883 1696 E-mail: [email protected] www.sffeco.com ce © GW. Y ERS [v2