Scribd
Upload
120 views1 page

Temperature Controllers: Conduction Type Thermostats B2 Series - Surface Mounted

The document describes Tempco conduction thermostats that can be used for surface mounting. They work by expanding and contracting the base plate in conjunction with a thermal strip, rather than just a bimetal strip. This provides minimum overshoot, smaller cycling differential, and faster response to heat loads. The base plate must be mounted fully against a flat, smooth heated surface using screws. Models are available with shaft lengths of 1.5 inches for voltages of 120VAC at 13.75A or 240VAC at 6.87A, with a temperature tolerance of ±5°F/2.7°C and operating range of 50 to 570°F/10 to 300°C. Optional preset calibrations are available

Uploaded by

edgartepe4324
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
120 views1 page

Temperature Controllers: Conduction Type Thermostats B2 Series - Surface Mounted

The document describes Tempco conduction thermostats that can be used for surface mounting. They work by expanding and contracting the base plate in conjunction with a thermal strip, rather than just a bimetal strip. This provides minimum overshoot, smaller cycling differential, and faster response to heat loads. The base plate must be mounted fully against a flat, smooth heated surface using screws. Models are available with shaft lengths of 1.5 inches for voltages of 120VAC at 13.75A or 240VAC at 6.87A, with a temperature tolerance of ±5°F/2.7°C and operating range of 50 to 570°F/10 to 300°C. Optional preset calibrations are available

Uploaded by

edgartepe4324
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Temperature Controllers

Surface Mount Thermostats


Conduction Type Thermostats B2 Series Surface Mounted

Tempco Conduction Thermostats do not use only a bonded bimetal


strip. The contacts are opened and closed by the expansion and contraction
of the base plate in conjunction with the thermal strip. Single pole, single
throw contacts open with temperature rise, providing minimum overshoot,
smaller cycling differential and faster response to heat load.
Installation Note: The heat-sensitive base plate of the thermostat must
be mounted in full contact with the heated surface. This surface should be
flat and smooth, and screws should be used for mounting.
File Number E224645

Agency Approvals:

Specifications

Typical Applications
Flat Irons
Solder Pots
Ironers
Vulcanizers
Deep Fryers
Sealing
Machines
Roasters
Sealing Irons

Ovens
Hot Plates
Industrial and
Laboratory
Applications

Voltage: 120 VAC @ 13.75A / 240 VAC @ 6.87A


Wattage: 1650
Temperature Tolerance: 5F /2.7C
Operation Range: 50 to 570F (10 to 300C)
Wiring: Tapped for #6-32 screws (included)
Endurance: 100,000 cycles
Contact Tempco for your OEM requirements
such as special range calibrations or shaft lengths.

Screwdriver Adjustment
(optional preset calibration)

Standard Models with Shaft

Designed for installation with the base plate in full contact


with heated surface. Pre-drilled holes facilitate mounting.
Temperature
Range F (C)

50 to 525F
(10 to 274C)
50 to 425F
(10 to 218C)

Amp Rating @
Overall Shaft
120 VAC 240 VAC
Length

13.75

13.75

6.87

6.87

1.5"

1.5"

Part
Number

TEB30001

TEB30002

Available with factory preset temperature calibration. This feature is optionalif required, specify temperature setting from
72F (22C) to 570F (300C).
The screw-adjust thermostat is offered in three temperature ranges:
Temperature
Range F (C)

Pre-Set
Tolerance

50 to 249F
(10 to 121C) 10F / 6C
250 to 399F
15F / 8C
(121 to 204C)
400 to 570F 20F / 11C
(204 to 300C)

Amp Rating @
120 VAC 240 VAC

Part
Number

13.75

6.87

TEB32000

13.75

6.87

TEB34000

13.75

6.87

TEB33000

Ordering Information

Choose the Part Number of the


conduction thermostat that is correct
for your application.
For pre-set TEB32XXX, TEB33XXX
and TEB34XXX thermostats consult
Tempco with your desired setpoint
for a Part Number.

(800) 323-6859 Email: [email protected]

13-81

You might also like