Scribd
Upload
344 views6 pages

Clamping Bushings

The clamping bush was developed for mounting gearboxes in wind turbines that use a three point suspension system. It consists of two half-bushes that are installed in clamping blocks on either side of the torque support. The clamping bush provides easy installation and optimal vibration damping characteristics for gearbox bearings in wind turbines ranging from 500 kW to 4.2 MW in power capacity.

Uploaded by

shelarsanjay
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
344 views6 pages

Clamping Bushings

The clamping bush was developed for mounting gearboxes in wind turbines that use a three point suspension system. It consists of two half-bushes that are installed in clamping blocks on either side of the torque support. The clamping bush provides easy installation and optimal vibration damping characteristics for gearbox bearings in wind turbines ranging from 500 kW to 4.2 MW in power capacity.

Uploaded by

shelarsanjay
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Clamping Bush

The clamping bush was developed for the


suspension of gearboxes of wind turbines
with three point mounting systems. Its most
remarkable features are the easy installation
as well as optimal vibration- and damping
characteristics.

The clamping bush consists


of two half-bushes, each of
which is installed in a clamping
block - before and after the
torque support.

Gear bearing of a 1.5 MW wind power


plant with clamping bushes
Clamping Bush

Bearing of a 2.5 MW wind


power plant with clamping
bushes

Bearing of a 1.5 MW wind


power plant with clamping
bushes

Bearing of a 0.8 MW wind


power plant with clamping
bushes

Energie- und Schwingungstechnik Mitsch GmbH


Auf der Rut 5 • D-64668 Rimbach • Phone: +49 (0) 6253 9885-0 • Fax: +49 (0) 6253 9885-50
E-Mail: [email protected] • Internet: www.esm-gmbh.de
Clamping Bush

Installation of clamping bushes


in 1 MW wind power plants

Bearing of a 2 MW plant

Clamping bushes are in use for wind power plants with


three point mounting system between a power range of
500 kW and 4.200 kW.
Clamping bush for
installation in the torque arm
The clamping bush is designed in order to bear the gear of wind
power plants with three-point-mounting-system. Its most remarkable
features are easy installation as well as optimal vibration characteristics.

The clamping bush is directly installed in the torque arm.

The attachment can be used simultaneously as installation device.

Energie- und Schwingungstechnik Mitsch GmbH


Auf der Rut 5 • D-64668 Rimbach • Phone: +49 (0) 6253 9885-0 • Fax: +49 (0) 6253 9885-50
E-Mail: [email protected] • Internet: www.esm-gmbh.de
Clamping bush for
installation in the torque arm

Easy installation, also in the closed torque arm.

The clamping bush is directly installed in the eye of the torque arm
with a new easy method.

After prestressing one half of


the bush, the second half can
be just pushed in easily.
Clamping bush for
installation in the torque arm

The easy installation was


proven in use at wind power
plants. The installation in
the nacelle is without
efforts.

Installation in 750 kW
wind power plants

Energie- und Schwingungstechnik Mitsch GmbH


Auf der Rut 5 • D-64668 Rimbach • Phone: +49 (0) 6253 9885-0 • Fax: +49 (0) 6253 9885-50
E-Mail: [email protected] • Internet: www.esm-gmbh.de

You might also like