Scribd
Upload
43 views

Project Report

This project report outlines the development of a new system. It proposes improvements over existing systems and describes the technologies, requirements, design, and implementation of the project. The system architecture is defined along with module descriptions. Screenshots and results are provided with conclusions on future enhancements.

Uploaded by

vijaykannamalla
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
43 views

Project Report

This project report outlines the development of a new system. It proposes improvements over existing systems and describes the technologies, requirements, design, and implementation of the project. The system architecture is defined along with module descriptions. Screenshots and results are provided with conclusions on future enhancements.

Uploaded by

vijaykannamalla
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Project Report

Table of Contents
1

Abstract ___________________________________________________________________ 1

Objective __________________________________________________________________ 1

2.1

Existing system ________________________________________________________________ 1

2.2

Proposed System ______________________________________________________________ 1

Introduction ________________________________________________________________ 1
3.1

Concept 1 ____________________________________________________________________ 1

3.2

Concept 2 ____________________________________________________________________ 1

3.3

Concept 3 ____________________________________________________________________ 1

Technologies _______________________________________________________________ 1
4.1

Technology 1 __________________________________________________________________ 2

4.2

Technology 2 __________________________________________________________________ 2

4.3

Technology 3 __________________________________________________________________ 2

Requirement Analysis ________________________________________________________ 2

Requirements _______________________________________________________________ 2

6.1

Software Requirements _________________________________________________________ 2

6.2

Hardware Requirements ________________________________________________________ 2

Design ____________________________________________________________________ 2
7.1
7.1.1
7.1.2

7.2
7.2.1
7.2.2

System Architecture ____________________________________________________________ 2


Diagram 1 ___________________________________________________________________________ 2
Diagram 2 ___________________________________________________________________________ 3

Module Description ____________________________________________________________ 3


Module 1 ____________________________________________________________________________ 3
Module 2 ____________________________________________________________________________ 3

Coding ____________________________________________________________________ 3

Screen Shots ________________________________________________________________ 3

10 Conclusion _________________________________________________________________ 3
11 Future Scope _______________________________________________________________ 3
12 References _________________________________________________________________ 3

1 Abstract
<This section should contain a concise description about the project.>

2 Objective
<This section should contain the objective of the system being developed.>

2.1 Existing system


<This section should contain a description about similar projects that are available in the
market and their limitations.>

2.2 Proposed System


< This section should contain a description of the proposed system and its advantages. >

3 Introduction
<This section should contain description about each concept which is covered in the project. For
example, if the project deals with multipliers, then an introduction should be given about this
concept. Similarly, if the project uses encryption, a description about encryption and encryption
techniques should be added.>

3.1 Concept 1
3.2 Concept 2
3.3 Concept 3

4 Technologies
<This section should contain a complete description of the technologies used in the project. If
the project is done in VLSI using VHDL language, then it should have the description of both
VLSI and VHDL language. Similarly, if the project has other ancillary technologies like

embedded systems, DSP, DIP etc., then the description of them should also be added.

4.1 Technology 1
4.2 Technology 2
4.3 Technology 3

5 Requirement Analysis
<This section is optional and should contain the list of requirements assumed for developing the
project. If the project is a simulation for IEEE, it should refer to the document appropriately.>

6 Requirements
6.1 Software Requirements
<This section should contain a description of the software required to execute the project.>

6.2 Hardware Requirements


<This section should describe the minimum hardware requirements for the proposed system.>

Design

7.1 System Architecture


<This section should describe the architecture used in the project and the reasons for selecting
the model.>

7.1.1 Diagram 1
<At least one diagram should be added with description.>

7.1.2 Diagram 2

7.2 Module Description


<This section should contain the description of all modules. The modules must be listed and the
criteria for dividing the project into the specified modules should be explained. After this, each
module should be described in detail.>

7.2.1 Module 1
<Add description.>

7.2.2 Module 2

8 Coding
<This section can showcase some of the module files (modules that are important) from the
project. The source as it is provided in the project should be specified. The coding guidelines
that are used in the project can also be added>

9 Screen Shots
<This section should contain the screen shots of the project results.>

10 Conclusion
<This section should conclude the project by briefing the development, execution and the
advantages.>

11 Future Scope
<This section should list the enhancements that are possible based on the current solution.>

12 References
<This section should contain the list of reference documents and books. If this is an IEEE project,
the list from the base paper can be used here.>

You might also like