ALVA B SERVICE MANUAL

TABLE OF CONTENTS
1. Specifications 1.1. Product Specifications 1.2. Name Plate 2. Installation Instructions 2.1. Moving and Installing 2.2. Detergent Box Group 3. Operating Instructions 5.1. LCD Screen, Function Buttons & Knobs 5.2. Program List 5.3. Program Details 5.5. Child Lock 4. Test Mode 6.1. Autotest 5. Service Mode 5.1. Service Autotest 5.2. Failure Codes 6. Troubleshooting Guide 7. Disassembly and Assembly Instructions 7.1. Top Plate 7.2. Door 7.3. Tub Bellows Seal 7.4. Detergent Drawer 7.5. Control Panel 7.6. Kick Plate 7.7. Front Panel 7.8. Upper Support Bracket 7.9. Detergent Drawer Housing 7.10. Power Cable Group and Parazit Filter 7.11. Electronic Pressure Switch (EPS) 7.12. Door Lock 7.13. Pump Motor 7.14. Front Counterweight 7.15. Heater 7.16. Tub Bellows Seal 7.17. Transport Screw 7.18. Upper Counterweight 7.19. Washing Group 7.20. Shock Absorber PIN 7.21. Belt 7.22. Driven Pulley 7.23. Motor 7.24. Tub Entrance with Bellow Hose 7.25. Pressure Switch Hose Group 7.26. Tub 7.27. Drum 8. Component Specifications 8.1. Drain Pump 8.3. Resistance 8.4. NTC 8.5. Valve 8.6. Electronic Pressure Switch (EPS) 8.7. Motor 8.8. Door Lock 9. Wiring Diagram 9.1. Wiring Diagram NA-127VB3 and NA-147VB3 PAGE 3 3 3 4 4 5 6 6 6 7 8 9 9 11 11 12 12 14 14 14 16 16 16 18 18 20 20 21 22 22 22 23 23 24 24 25 25 26 26 26 26 27 27 27 27 28 28 30 32 34 36 37 40 42 42

1.
1.1.

Specifications
Product Specifications
42 lt Product Type Capacity Max Spin Speed (r/min) Energy Consumption Water Consumption Wash Programs Height Dimensions Width Depth Other Features Delay Time Front Loader 5 kg 400 500 600 800 1000 A 43 L/cycle 15 settings 84,5 cm 59,7 cm 49,7 cm Child Lock

1.2.

Name Plate

SERVICE INDEX NUMBER

0000

2.
2.1.
2.1.1.
1.

Installation Instructions
Moving and Installing
Removal of Transportation Screw
Transportation screws, which are located at the back side of the machine, must be removed before running the machine. Loosen the screws by turning them anticlockwise with a suitable spanner. 4. The holes where the transport screws have been removed should be covered with the plastic transport caps found in the accessories bag.

2.

3.

Pull out the screws and rubber washers.

5.

The transportation screws that have been removed from the machine must be re-used in any future transporting of the machine.

2.1.2.
1. 2.

Foot Adjustment
Do not install machine on rugs or similar surfaces. For machine to work silently and without any vibration, it should be installed on a flat, non-slippery firm surface. Any suspended floor must be suitably strengthened. You can adjust the level of machine using its feet. First, loosen the plastic adjustment nut away from the cabinet base.

5. 6. 7.

3. 4.

Change the level by adjusting the feet upwards or downwards. After level has been reached, tighten the plastic adjustment nut again by rotating it upwards against the base of the cabinet. Never put cartons, wooden blocks or similar materials under the machine to balance irregularities of the floor.

2.1.3.
1. 2.

Electrical Connection
Washing machine requires a 50Hz supply of 220240Volts. A special earthed plug has been attached to the supply cord of washing machine. This plug must be fitted to an earthed socket. The fuse value fitted to this plug should be 13 amps. If you have any doubts about electrical supply, consult a qualified electrician.

THIS APPLIANCE MUST BE EARTHED. Insert the machines plug to a grounded socket which you can easily reach.

2.1.4.
1. 2.

Water Supply Connection

Washing machine is supplied with a single (cold) water inlet. To prevent leakage from the connection joints, a rubber washer is included in the hose packing. Fit this washer at the end of water inlet hose on the tap side. Connect the hose to the water inlet valve. Tighten the plastic connector by hand. Please call a qualified plumber if you are unsure about this. Water pressure of 0,1-1 MPa from tap will enable machine to work more efficiently.(0,1 MPa pressure means water flow of more than 8 litres in 1 minute from a fully opened tap) 5. 6. After connection is complete, check for leakage by turning on tap completely. Make sure that water inlet hoses can not become folded, damaged, stretched or crushed when the washing machine is in its final position. Mount the water inlet hose to a threaded water tap.

3.

7.

4.

3.

2.1.5.
1. 2.

Drain Connection
Make sure that water inlet hoses are not folded, twisted, crushed or stretched. The drain hose should be mounted at a minimum height of 60 cm, and a maximum height of 100 cm from the floor. 4.

The end of the drain hose can be connected directly to a drainage stand-pipe or alternatively to a specific connection point designed for that purpose on the waste outlet of a sink unit. Do not extend the drain hose or guarantee will be invalidated.

2.2.

Detergent Box Group

VALVE1 MAIN SOFTENER PREWASH VALVE2

PREWASH MAIN SOFTENER

= WATER ENTRY VALVE 1 = WATER ENTRY VALVE 2 = WATER ENTRY VALVE 1 + VALVE 2

3.
3.1.

Operating Instructions
LCD Screen, Function Buttons & Knobs
SW1 SW2 SW3 SW4 PT PR

PR SW1 SW2 SW3 SW4 PT

Program selector 16 programs with ON/OFF. Switch 1, Start / Pause Switch 2, Function 1 Selection Switch 3, Function 2 Selection Switch 4, Function 3 Selection PT speed potentiometer

3.2.

Program List
Knob Position Pos1 Pos2 Pos3 Pos4 Pos5 Pos6 Pos7 Pos8 Pos9 Pos10 Pos11 Pos12 Pos13 Pos14 Pos15 Pos16 Pos17 Pos18 Pos19 Pos20 Program COTTON90C COTTON 60C PR W COTTON 60C COTTON 40C ECO WASH COTTON 30'C QUICK WASH COTTON COLD MIX WASH SYNTHETICS 60C BABY WASH SYNTHETICS 40C SPORT WEAR SYNTHETICS COLD CURTAIN WASH DELCATE 30'C DELICATE COLD HAND WASH WOOL 30C WOOL COLD

3.3.

Program Details

Program Details for 42 lt

Total Water Consumption (lt)

Total time (min)

Max. T(C)

Max U/min For 1000 rpm

Max.energy(kwh)

COTTON90C COTTON 60C PR W COTTON 60C COTTON 40C ECO WASH QUICK WASH COTTON COLD SYNTHETICS 60C SYNTHETICS 40C SYNTHETICS COLD DELCATE 30'C WOOL 30C

61lt 52lt 43lt 55lt 41lt 33lt 55lt 33lt 33lt 33lt 52lt 56lt

139 128 143 111 80 43 79 61 73 71 70 65

80 55 57 40 40 25 * 55 40 * 30 30

950 950 950 950 950 800 950 800 800 800 560 560

1,32 0,78 0,95 0,43 0,39 0,16 0,24 0,79 0,53 0,14 0,34 0,29

Program Details for 42 lt New Regulation

Total Water Consumption (lt)

Total time (min)

Max. T(C)

Max U/min For 1000 rpm

Max.energy(kwh)

COTTON90C COTTON 60C PR W COTTON 60C COTTON 40C ECO WASH QUICK WASH COTTON COLD SYNTHETICS 60C SYNTHETICS 40C SYNTHETICS COLD DELCATE 30'C WOOL 30C

75 74 43 45 43 40 56 45 45 45 56 52

155 140 190 180 80 30 110 84 65 72 70 73

83 57 57 40 40 25 WIT 55 40 WIT 30 29

950 950 950 950 950 800 950 800 800 800 560 560

1,96 0,89 0,85 0,82 0,39 0,16 0,17 0,95 0,53 0,12 0,34 0,29

* WIT

: Programme duration ,Energy and Water Consumption are given for the cycles for programmes are started in set temperature. : Water Inlet Temperature : Programmes do not take water Temperature may vary depending on the heating time Durations may vary according to wash load (weight and type), tap water and ambient temperature and selected extra functions.

3.5.
Activation 1.

Child Lock
Press the 1. and 3. function button for 4-5 seconds. 2. The Chihl Lock Symbol is appear on the lcd display.

Deactivation 1. Press the 1. and 3. function button for 4-5 seconds. 2. The Child Lock Symbol is deleted on the lcd display.

Activation Indication 1. The symbol (I6) makes fast blink for indication and is then fix on.

Deactivation Indication 1. Option icon makes fast blink and is then off.

Child lock during the programme 1. Machine does not respond to any pressing of buttons or changing position of program knob but option icon makes fast blink to evoke the user.

In Error Mode 1. Child lock will be automatically deactivated when error is detected except NTC (E05) and Voltage (E09) errors. When E05 and E09 is detected, the child lock will be deactivated at the end of the program or the user will be able to deactivate it. On other hand, if the user brings the programme knob to zero and then any position during these two error modes, firstly it will show child lock active indication and then the error indication and it will continue the cycle.

In end condition 1. When cycle is finished child lock is deactivated. automatically

4.
4.1.

Test Mode
Autotest

* This test is for quick checking of the product. You can not see the failure codes. 1. After selecting spin speed to max, select the program 3 4. Release 1. function button

2.

Press 1. function button

5.

Press 1. Function button again.

3.

While pressing 1. function button, change position of the third to second

6.

While pressing 1. function button, change position of the first to second

10

5.
5.1.

Service Mode
Service Autotest

Activation Press function 1 and function 2 buttons at the same time and while pressing the buttons bring program selector to position 1. All LEDs (Func1&2) will be OFF and machine will get into service autotest mode. While getting into service autotest, door will be locked. Service autotest will be done step by step. It has to be done consecutively starting from Autotest 1.

In cases of: 1. Bringing program knob to zero position 2. Bringing program to a backwards position Service autotest will be cancelled. Changes 1. Selector position 1 will be Motor CW low speed

Speed will be 53 rpm for all models. Machine will turn with 53 rpm for 1 minute and then will stop. As soon as it stops, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 1 is 1 minute. Note: If user changes the selector position without waiting for 1 min., machine will do what is defined for the new selected position. 2. Selector position 2 will be Motor CCW low speed

Speed will be 53 rpm for all models. Machine will turn with 53 rpm for 1 minute and then will stop. As soon as it stops, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 2 is 1 minute. Note: If user changes the selector position without waiting for 1 min., machine will do what is defined for the new selected position. 3. Selector position 3 will be Motor CCW sense high speed

Machine will check if there is water inside the drum (level is higher than Empty) and if there is, machine will drain water befor e ramping up to maximum. Machine will ramp up to maximum speed, will stay there for 5 seconds and then will stop. As soon as it stops, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 3 is about 1 minute. Note: There should be no load inside the drum in this position cos ramp will be done without unbalance control. 4. Selector position 4 will be Door Unlocked

When door is unlocked: END LED (LED 5) will be ON After 5 seconds than door is unlocked, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 4 is about 2 minutes. Note: To see the effect of this step we should wait for about 1 min. till door gets unlocked. 5. Selector position 5 will be Door Locked

When door is locked: START/PAUSE LED (LED 1) will be ON After 30 seconds than door is unlocked, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 5 is about 1 minute.

11

6. Selector position 6 will be Valve 1 ON

Valve 1 will be open for 30 seconds and then will stop. As soon as it stops, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 6 is about 30 seconds. Note: If user changes the selector position without waiting for 30 seconds, machine will do what is defined for the new selected position. 7. Selector position 7 will be Valve 2 ON

Valve 2 will be open for 30 seconds and then will stop. As soon as it stops, all function LEDs will flash.This will mean machine is ready to go to next position. So, time for selector position 7 is about 30 seconds. Note: If user changes the selector position without waiting for 30 seconds, machine will do what is defined for the new selec ted position. 8. Selector position 8 will be HEATER ON

Important points: 1. Water level will be checked before heating and if level is below P0 machine will fill water with main wash valve till P1 2. Connection of NTC will be checked. If there is no connection (open or short circuit), machine will give heating failure 3. If temperature doesnt increase 2C in 8 minutes, machine will again give heating failure. Heating failure is: START (L1) and END (L5) LEDs will flash, After 8 min if there is a failure machine will give failure and if there is not, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 8 is about 8 minute. Note: If user changes the selector position without waiting for 15 min., machine will do what is defined for the new selected position. 9. Selector position 9 will be PUMP ON NTC will be checked firstly. If the measured temperature is higher than 50C, then it takes 80 sec cooling water. It will drain until "Pzero plus Empty" Pump will be open for till Empty level reached + 15 sec. and then will stop. As soon as it stops, all function LEDs will flash. This will mean machine is ready to go to next position. So, time for selector position 9 is about 1, 5 - 2 minutes. Note: User should wait till pump activation completely finishes in order not to affect behavior of other selector positions. After position 9; user interface, LED and button check will begin and for these positions, behavior can be followed from the chart.

Notes: 1. For these positions there will be no time restriction (these responses of machine carry no risk of safety), user will manage this. 2. Machine will not warn or indicate that it is ready to go to next position (like all function LEDs flash which we will use for first 9 positions)

because there is no certain and restricted time for these responses. User can pass to next position as soon as completing check of current position

SELECTOR POSITION 10 MODEL Result

SELECTOR POSITION 11 Result

SELECTOR POSITION 12

SELECTOR POSITION 13

SELECTOR POSITION 14

SELECTOR POSITION 15

Action

Result

Action

Result

Action

Result

Action

Result

PUSH BUTTON LED START/PAUSE TEMPERATURE START/PAUSE ON SELECTOR MIN B2 L1, L2, L3 ON L4 & L5 ON PUSH BUTTON FUNC 1 PUSH BUTTON FUNC 2 LED FUNC 1 ON TEMPERATURE SELECTOR MAX TEMPERATURE SELECTOR MID

L5 ON

L4 ON

NO ACTION

ALL LEDS FLASH

NO ACTION

END LED ( L5 ) ON

LED FUNC 2 ON

L4 & L5 ON

12

5.2.

Failure Codes
Error Indication Error Number E01 E01 E02 E03 E04 E05 E06 E08 E10 Indication For User Yes/No Yes Yes Yes Yes Yes No No No No Indication For Service Yes/No Yes Yes Yes Yes Yes Yes Yes Yes Yes

Door is not locked Door is unlocked during programme Lack of water Pump failure Overflow NTC or Heater Failure Motor Failure - 1 (Tachometer open-short circuit or motor connector is disconnected) Motor Failure - 2 (triac short circuit) Electronic Pressure Sensor

6.

Troubleshooting Guide

All repairs which must be done on the machine should be done by authorized agents only. When a repair is required for machine or you are unable to eliminate the failure with the help of the information given below: Unplug the machine. Close the water tap.

FAILURE

PROBABLE CAUSE It is unplugged. Fuse is defective. Start / Pause button has not been pressed.

METHODS OF ELIMINATION Insert the plug into the socket. Change fuse. Press the start / pause button. Bring the program knob on the desired status. Shut the door properly. You should hear the click. See page 9. Open water tap. Check the water inlet hose. Clean the filters of water inlet hose. Clean the valve inlet filters. Shut the door properly. You should hear the click. Check the drain hose. Clean the pump filter. Spread the clothes inside the machine in an orderly and well-balanced manner. Adjust the feet. Remove transportation screws. It does not prevent operation of the machine. Do not exceed the recommended quantity of clothes and spared clothes in the machine in a well-balanced manner.

Machine does not operate.

The program knob is in 0 (off) status. The door is not shut properly. Child lock is active. Water tap is closed. The water inlet hose may be bent. The water inlet hose is obstructed. The water inlet filter is obstructed. The door is not shut properly. The drain hose is obstructed or bent. The pump filter is obstructed. The clothes are not placed inside the machine in a well-balanced manner. The feet of machine are not adjusted. Transportation screws are not removed. There is a small amount of clothes in the device. Excessive amount of clothes are filled in the machine or the clothes are not placed in a well-balanced manner.

Machine does not receive water.

Machine is not draining water.

Machine is vibrating.

13

FAILURE

PROBABLE CAUSE

METHODS OF ELIMINATION Press the start/pause button. In order to stop the foam, dilute one table-spoon of softener in half liter of water and pour it in the detergent drawer. Press the start/pause button after 5-10 minutes. Arrange the amount of the detergent properly in the next washing process. Use only the detergents produced for full automatic machines. Select a suitable program. Use more detergent according to the detergent. Put the clothes in machine in a manner not to exceed its maximum capacity. Use the amount of detergent according to the declaration of the detergent producer. Spread the clothes inside the machine in an orderly and well-balanced manner.

Excessive foam in the detergent drawer

Too much detergent has been used.

Wrong detergent has been used. The washing result is bad. Laundry too dirty for the program you have selected. The amount of detergent used is not sufficient. Clothes exceeding the maximum capacity has been filled in machine. Water may be hard. Distribution of the clothes in machine is not well-balanced. The water is seen in the drum during washing. There are residues of detergent on the clothes. There are grey stains on the clothes. No failure. The water is at the lower part of the drum. The pieces of some detergents which do not dissolve in water may stick to clothes as white stains. These stains may be caused by oil, cream or ointment.

The washing result is not good.

The spinning No failure. The unbalanced load process is not done control works in that way. or starts with delay.

By calibrating machine for Rinsing program, make an additional rinsing or eliminate the stains After drying with the help of a brush. In the next washing operation, use the maximum detergent amount declared by the detergent producer. The unbalanced load control system will try to distribute clothes in a homogenous manner. After clothes are distributed, passage to spinning process will be realized. In the next washing process, place clothes into the machine in a well-balanced manner.

14

7. Disassembly and Assembly Instructions

7.1.
1.

Top Plate
Remove two screws that fix the top-plate at the back. 2. Pull the door up.

2.

Push the top-plate back and pull it up.

3.

Remove screws that fix the door group.

2 1

7.2.
1.

Door
Remove two screws that fix the door. (by using the T25) 4. Put the door outside plastic with helping screwdriver as it is shown in the picture.

T25

15

5.

Remove the door inside plastic as it is shown in the picture.

8.

Remove the door handle pim as it is shown in the picture.

6.

Remove six screws that fix the door hinge as it is shown in the picture.

7.

Remove the door handle as it is shown in the picture.

16

7.3.
1.

Tub Bellows Seal

First remove the spring wire fixing the tub bellows seal by using the small size screw driver. Pull the tub bellows seal as it is shown in the picture.

7.4.
1.

Detergent Drawer
Remove the detergent drawer and pull it up carefully

2.

Remove the tub bellows seal-body fixing spring.

7.5.
1.

Control Panel
Remove the screw which fix the control panel to the front panel.

17

2.

Remove three screws fixing the control panel.

5.

Remove the lcd communication cable as it is shown in the picture.

3.

Pull the control panel up.

6.

Remove electronic card cover as it is shown in the picture by using small screw driver.

4.

Remove connectors as it is shown in the picture.

7.

Remove lcd electronic card as it is shown in the picture.

18

7.6.
1.

Kick Plate
Remove the right part of the kickplate as it is shown in the picture.

7.7.
1.

Front Panel
Remove two screws fixing the front panel at the bottom as it is shown in the picture by using T25

2.

Remove two screws fixing the kickplate.

2.

Remove two screws fixing the door lock as it is shown in the pictures.

3.

Pull the kickplate left and push it down.

19

3.

Remove the tub bellows seal as it is shown in the pictures.

6.

Remove the front panel as it is shown in the pictures.

4.

Remove two screws fixing front panel at the upper as it is shown in the picture.

5.

Remove two screws fixing front panel at the below as it is shown in the picture.

20

7.8.
1.

Upper Support Bracket

Remove two screws fixing the body group at the front as it is shown in the picture.

7.9.
1.

Detergent Drawer Housing

Remove the tub seal clamp by using the pliers, which is attached to the detergent drawer housing.

2.

Remove two screws fixing the body group at the upper as it is shown in the picture.

2.

Remove the four connectors that is connected to the feed valve as it is shown in the picture.

3.

Remove detergent drawer group two clips fixing the upper support bracket as it is shown in the picture.

3.

Turn the feed valve counter clockwise slightly to remove.

21

4.

Remove the detergent drawer screw.

2.

Remove two screws fixing the parasite filter.

5.

Remove the detergent drawer housing assembly.

3.

Pull the power cable group up as it is shown in the picture.

7.10.
1.

Power Cable Group and Parazit Filter

Remove the five conectors that is connected to the parasite filter. 4. Remove parasite fitler fixing body group as it is shown in the picture.

22

7.11.
1.

Electronic Pressure Switch (EPS)

Remove the connector that is connected to the EPS.

7.12.
1.

Door Lock
Remove the connector that is connected to the door lock.

7.13.
2. Pull the EPS upward to remove as it is shown in the picture. 1.

Pump Motor
Remove pipe clip that fixes the drain hose.

3.

Remove the eps hose handcuffs and eps hose as it is shown in the picture.

2.

Remove pipe clip fixing the tub outlet hose.

23

3.

Remove the connector that is connected to the pump motor.

2.

Pull the counterweight back

7.15.
4. Remove four screws fixing the pump motor. 1.

Heater
Remove the four connectors that is connected to the heater.

7.14.
1.

Front Counterweight
Remove four screws fixing the front counterweight on the front. (Box wrench size 13 mm)

2.

Remove one nut fixing the heater slightly (box wrench size 8 mm)

24

3.

Hold the heater and pull it out.

7.17.
1.

Transport Screw
Remove four transport screws (box wrench size 10 mm)

7.16.
1.

Tub Bellows Seal

Remove the tub gasket clip by using small screwdriver. 2. Hold the transport screw and pull it out.

2.

Hold the tub bellows seal and gasket-body fixing spring together, and pull them up.

25

7.18.
1.

Upper Counterweight
Remove two screws fixing the upper counterweight by using box wrench size 13 mm. 2. Cut the five lead wire holders as shown the pictures. a) b)

c)

d)

2.

Remove the upper counterweight

3.

Remove the four screws fixing the spring hanger sheet iron.

7.19.
1.

Washing Group
Remove the connector that is connected to the motor. 4. Remove the washing group as it is shown in the picture.

26

7.20.
1.

Shock Absorber PIN

Remove two pins fixing the shock absorber as shown in the picture. 2. Remove the driven pulley it is shown the picture.

7.21.
1.

Belt
Remove the belt as it is shown the picture.

7.23.
1.

Motor
Remove the four screws fastening the motor under the tub by using T40

7.22.
1.

Driven Pulley
Remove the screw fixing driven pulley it is shown the picture (By using T40). 2. Pull the motor up for disassembly.

27

7.24.
1.

Tub Entrance with Bellow Hose

Remove the tub entrerance with bellow hose.

7.26.
1.

Tub
Remove twenty four screws fixing tub using box wrench size 8 mm.

7.25.
1.

Pressure Switch Hose Group

Remove screw fixing the pressure switch water reservoir.

7.27.
2. Remove the tub exit with bellow hose with ball by using box wrench size 10 mm. 1.

Drum
Remove the drum.

28

8.
8.1.

Component Specifications
Drain Pump

Drain pump is both a mechanical and elektrical component which is used to drain water inside the washing machine. It has an synchronous motor inside. For better performance maintanance, pump filter should be cleaned regularly.

8.1.1.

Technical Features

Nominal voltage Nominal current Nominal power Frequency Resistor (coil) Water flow: Thermal protector

220 - 240 V 0.28 A (10 %) 37 W 50 Hz 130 (5%) 17 L/min(to 1 m height) YES

8.1.2.

Checking of Component

Check the resistance value on the component with multimeter as shown in belows figures. Resistance value should be between 125- 140

Checking the component

29

8.1.3.

Component Controlling By Connection Measurement

You can determine the ohm value by measuring from the blue cable and blue cable (refer wiring diagram at page 43) as shown in belows figure. Resistance value should be between 125- 140

Blue Cable

Blue Cable

30

8.2.

Resistance

Heating element (Resistance) is a component which is desingned to regulate temperature of water inside the drum. It has three connections: Phase, notral and ground connections.

8.2.1.

Technical Features
Tubular heating element with NTC sensor 230 V 2000 W (5%) 24,8 5% (for NA-127VB3 and NA-147VB3) 2 sided

Kind of heating Nominal voltage Nominal power Resistance Thermal fuse

8.2.2.

Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures.

Checking the component

31

8.2.3.

Component Controlling By Connection Measurement

You can determine the ohm value by measuring from the grey cable and brown cable (refer wiring diagram at page 43) as shown in belows figures. Resistance value should be between 23- 27 Ohm.

Brown Cable

Grey Cable

32

8.3.

NTC

Component which sends signals to PCB about the water temperature inside the tub. The Resistance (Ohm) value of the NTC decreases as the temperature increases.

8.3.1.

Technical Features
Tem (C) -10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 R min (k) 54,9 43,0 33,9 27,0 21,6 17,4 14,1 11,5 9,4 7,8 6,4 5,4 4,5 3,8 3,2 2,7 2,3 1,9 1,7 1,4 1,2 1,1 0,9 R max (k) 62,6 48,6 38,1 30,1 23,9 19,1 15,4 12,5 10,2 8,3 6,9 5,7 4,7 3,9 3,3 2,8 2,4 2,0 1,8 1,5 1,3 1,1 1,0

NTC Tempure Resistance Values

8.3.2.

Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures.

Checking the component

33

8.4.

Valve

Valve is an electrical and mechanical component which is designed to take water from the network system into the washine machine. It is operated by PCB card.

8.4.1.

Technical Features

Nominal voltage Nominal power Frequency Rated flow: Operating water pressure

220 240 V 8 VA 50-60 Hz 7 lt/min (15 %) 0.0,3 1 Mpa

8.4.2.

Checking of Component

Check the resistance value on the component with multimeter as shown in below pictures. Valve water flow rate should be between 6 lt/min - 8 lt/min. Each valve bobbin resistance values should be between 3,3 - 4.2 kohm .

Checking the component

34

8.5.

Electronic Pressure Switch (EPS)

8.5.1.

Technical Features

Electromagnetic field occurs as a result of the vibration of the membrane which is under pressure in the coil. The nucleus part is moved up and down by the electromagnetic field. The water level is regulated by the frequency which is controlled by the PCB and changes according to the movement of the nucleus part.

8.5.2.
1.

Checking of Component
Push the door lock slider with screwdriver. 6. Cut off the energy input when the water intake finishes and drum begins to rotate.

5.

Select the 1st program and start the machine.

7.

Check the water level inside the drum with ruler. It should be 10 cm 1.

35

8.6.

Motor

The washing machine has an asynchronous motor. It is controlled by the PCB. It is essential to check the motor for correct diagnosis and quick servicing. In the below picture, socket points on the motor is shown to measure with multimeter.

Tacho Socket Terminal

Stator Full Field Coil Socket Terminal

Stator Half Field Coil Socket Terminal

Motor Socket Terminals

36

Tacho and stator (full field-half field) ohm resistance values for the motor types are listed in the below table.

MOTOR KODU 32003986 32004905 32006966 32007450 32004572 32008809 30027193 30023397 32002064 32003425 32000536 32000271 32000535 30027193 32008661 30023397 32004970 32004969 32009041 32004968 32009040 32008659 32008660 32005496 32007954 32007955 32008852 32008853

FRMA ACC ACC ACC ACC ACC ACC ANAIMEP ANAIMEP ANAIMEP ANAIMEP ASKOLL (CESET) ASKOLL (CESET) ASKOLL (CESET) ASKOLL (CESET) ASKOLL (CESET) ASKOLL (CESET) ATB ATB ATB ATB ATB BROAD OCEAN BROAD OCEAN IDEA WELLING WELLING WELLING WELLING

STATOR (TAM SARGI) (ohm) 3.30-/+ 7% 2.70-/+ 7% 3.00-/+ 7% 2.70-/+ 7% 1.20-/+ 7% 0.96-/+ 7% 1.87-/+7% 1.75-/+7% 2.01-/+7% 2.01-/+7% 1.01-/+7% 1.40-/+7% 1.24-/+7% 2.26-/+7% 1.90-/+7% 1.83-/+7% 1.62-/+ 7% 1.62-/+ 7% 1.62-/+ 7% 1.20-/+ 7% 1.20-/+ 7% 2.15-/+7% 2.15-/+7% 4.60-/+7% 2.08-/+7% 1.59-/+7% 2.00-/+7% 2.15-/+7%

TAKO (ohm) 184-/+7% 184-/+7% 184-/+7% 184-/+7% 184-/+7% 184-/+7% 180-/+10% 180-/+10% 180-/+7% 180-/+7% 68.7-/+7% 68.7-/+7% 68.7-/+7% 68.7-/+7% 68.7-/+7% 68.7-/+7% 87-/+12% 87-/+12% 87-/+12% 87-/+12% 87-/+12% 66.7-/+7% 66.7-/+7% 227-/+7% 66.6-/+7% 66.6-/+7% 66.6-/+7% 66.6-/+7%

STATOR (YARIM SARGI) (ohm) 1.20-/+7% 1.04-/+7% 1.50-/+7% 1.08-/+7% 0.60-/+7% 0.56-/+7% 0.74-/+7% 0.81-/+7% 0.81-/+7% -

SICAKLIK 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C 20 C

Resistance values for the motor types

37

8.7.

Door Lock

Door lock is activated at the beginning of the program in order to prevent the door from opening. It can be unlocked approximately after 2 minutes of the program end. This time delay is caused by the PTC which is assambled in the door lock.

8.7.1.

Technical Features
2 6 35 75 220 V 16 (4) A

Lock Time (20 C) Unlock Time (20 C) Nominal voltage Nominal current

8.7.2.

Checking of Component

Check the resistance value on the component with multi-meter as shown in below figures. Resistance value on the PTC should be 1000 50% at 25 C. That resistance value can be measured from terminal 3-4 (See wiring diagram page 51 below).

2 3 4 5

38

9.
9.1.

Wiring Diagram
Wiring Diagram

9.1.
Power Cable

Wiring Diagram

Parasite Filter

Br Gr Blu Bla Wh Y Bla Bla

Resistance Valve
Y

Blu Blu

NTC (Temperature Sensor)

EPS

Bla Blu Br Gr P R Wh Y

: Black : Blue : Brown : Grey : Pink : Red : White : Yellow

Pump

Door Lock

Motor

40