MiCOM P343

Generator Protection Relay P343/EN PM/J86

Software Version 35A

PICS and PICS

Note:

The technical manual for this device gives instructions for its installation, commissioning, and operation. However, the manual cannot cover all conceivable circumstances or include detailed information on all topics. In the event of questions or specific problems, do not take any action without proper authorization. Contact the appropriate Schneider Electric technical sales office and request the necessary information. Any agreements, commitments, and legal relationships and any obligations on the part of Schneider Electric including settlements of warranties, result solely from the applicable purchase contract, which is not affected by the contents of the technical manual. This device MUST NOT be modified. If any modification is made without the express permission of Schneider Electric, it will invalidate the warranty, and may render the product unsafe.

The Schneider Electric logo and any alternative version thereof are trademarks and service marks of Schneider Electric. All trade names or trademarks mentioned herein whether registered or not, are the property of their owners. This manual is provided for informational use only and is subject to change without notice. 2011, Schneider Electric. All rights reserved.

MiCOM P343

PICS and MICS

CONTENTS
1 PROTOCOL IMPLEMENTATION CONFORMANCE STATEMENT (PICS) 1.1 Introduction 1.2 ACSI Basic Conformance Statement 1.3 ACSI Models Conformance Statement 1.4 ACSI Service Conformance Statement MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS) 2.1 Introduction 2.2 Objective 2.3 Logical Device Definitions
2.3.1 IEC 61850 Logical Device Data Model

5 5 5 5 6 10 10 10 10
11

2.4
2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 2.4.6 2.4.7 2.4.8 2.4.9 2.4.10 2.4.11 2.4.12 2.4.13 2.4.14 2.4.15 2.4.16 2.4.17 2.4.18 2.4.19 2.4.20 2.4.21 2.4.22 2.4.23 2.4.24 2.4.25 2.4.26 2.4.27 2.4.28 2.4.29 2.4.30

Logical Node Definitions

Logical Node: GGIO_ALM_96 Logical Node: GGIO_ANAL_10 Logical Node: GGIO_IND_32 Logical Node: GGIO_IND_32_CTRL Logical Node: GGIO_IND_8 Logical Node: LLN0_CONTROL Logical Node: LLN0_P343 Logical Node: LLN0_STANDARD Logical Node: LLN0_SYSTEM Logical Node: LPHD_STANDARD Logical Node: MDIF_ALL Logical Node: MMTR_AFQ Logical Node: MMTR_PRIV Logical Node: MMXU_DERIVED_ALL Logical Node: MMXU_RMS Logical Node: MMXU_ROTOR_EF Logical Node: MMXU_SENSITIVE Logical Node: MMXU_STANDARD_ALL Logical Node: MMXU_STANDARD2_NO_VN Logical Node: MMXU_THIRD_HARMONIC Logical Node: MMXU_VHZ Logical Node: MSQI_ALL Logical Node: MSTA_STANDARD Logical Node: PDIF_NEU Logical Node: PDIS_SYSTEM Logical Node: PDMP_NORMAL Logical Node: PDUP_STANDARD Logical Node: PEFI_NEU_UR Logical Node: PPAM_STANDARD Logical Node: PPWR_NORMAL

15
17 19 20 21 22 22 22 24 24 24 25 25 25 26 26 27 27 27 28 28 28 29 29 29 30 30 30 31 31 31

P343/EN PM/J86

Page 1

PICS and MICS

MiCOM P343

2.4.31 2.4.32 2.4.33 2.4.34 2.4.35 2.4.36 2.4.37 2.4.38 2.4.39 2.4.40 2.4.41 2.4.42 2.4.43 2.4.44 2.4.45 2.4.46 2.4.47 2.4.48 2.4.49 2.4.50

Logical Node: PTAF_NO_SEG Logical Node: PTOC_NEU Logical Node: PTOC_NO_SEG Logical Node: PTOF_NO_SEG Logical Node: PTOV_NEU Logical Node: PTOV_NO_SEG Logical Node: PTRC_NO_SEG Logical Node: PTTR_NO_SEG Logical Node: PTTR_NO_SEG_PRIV Logical Node: PTUC_NEU Logical Node: PTUF_NO_SEG Logical Node: PTUV_NO_SEG Logical Node: PVOC_STANDARD Logical Node: PVPH_STANDARD Logical Node: RBRF_EXTTRIP Logical Node: RCLI_STANDARD Logical Node: RDRE_BASIC Logical Node: RTTR_STANDARD Logical Node: RVCS_STANDARD Logical Node: XCBR_BASIC

32 32 32 33 33 33 34 34 34 35 35 35 36 36 36 37 37 37 38 38

2.5
2.5.1 2.5.2 2.5.3 2.5.4 2.5.5 2.5.6 2.5.7 2.5.8 2.5.9 2.5.10 2.5.11 2.5.12 2.5.13 2.5.14 2.5.15 2.5.16 2.5.17 2.5.18 2.5.19 2.5.20 2.5.21 2.5.22 2.5.23 2.5.24 2.5.25

Common Data Class Definitions

Common Data Class: ACD_NO_SEG Common Data Class: ACD_NO_SEG_NS Common Data Class: ACT_NO_SEG Common Data Class: ACT_NO_SEG_NS Common Data Class: ASG_FLOAT Common Data Class: BCR_PRIV Common Data Class: CMV_MAG_ANG_FLOAT Common Data Class: CMV_MAG_FLOAT Common Data Class: DEL_SEG Common Data Class: DEL_SEG_NS Common Data Class: DPC_STATUS Common Data Class: DPL_STANDARD Common Data Class: INC_MOD Common Data Class: INC_MOD_D_PRIV Common Data Class: INC_MOD_PRIV Common Data Class: INS_BASIC Common Data Class: INS_BEH Common Data Class: INS_BEH_D_PRIV Common Data Class: INS_HEALTH Common Data Class: INS_NO_TIME_NS Common Data Class: LPL_LLN0 Common Data Class: LPL_LN Common Data Class: LPL_LN_P Common Data Class: MV_FLOAT Common Data Class: MV_FLOAT_D

39
40 40 40 41 41 41 42 42 43 43 43 44 44 44 45 45 45 45 46 46 46 46 47 47 48

Page 2

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.26 2.5.27 2.5.28 2.5.29 2.5.30 2.5.31 2.5.32 2.5.33 2.5.34 2.5.35 2.5.36 2.5.37 2.5.38 2.5.39 2.5.40

Common Data Class: MV_FLOAT_NS Common Data Class: SEQ_MAG_ANG Common Data Class: SPC_CONTROL Common Data Class: SPC_CTRL_PRIV Common Data Class: SPC_STATUS Common Data Class: SPS_D Common Data Class: SPS_WD Common Data Class: SPS_WD_NS Common Data Class: SPS_WD_PRIV Common Data Class: WYE_RES_ANG_D_NS Common Data Class: WYE_RES_MAG_D Common Data Class: WYE_RES_MAG_NS Common Data Class: WYE_SEG Common Data Class: WYE_SEG_NS Common Data Class: WYE_SEG_PHASEA

48 49 49 50 50 50 51 51 51 51 52 52 52 52 52

2.6
2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6

Common Data Attribute Type Definitions

Component: AnalogueValue_Float Component: Originator Component: RangeConfig_Deadband Component: Unit_multiplier Component: Vector_Magnitude_Float Component: Vector_MagnitudeAngle_Float

53
53 53 53 53 54 54

2.7
2.7.1 2.7.2 2.7.3 2.7.4 2.7.5 2.7.6 2.7.7 2.7.8 2.7.9 2.7.10 2.7.11 2.7.12

Enumerated Type Definitions

Enumerated Type: AddCause Enumerated Type: Beh Enumerated Type: Bypass Enumerated Type: ctlModel Enumerated Type: Dbpos Enumerated Type: dir Enumerated Type: Health Enumerated Type: Mod Enumerated Type: multiplier Enumerated Type: orCategory Enumerated Type: seqT Enumerated Type: SIUnit

55
55 55 55 55 56 56 56 56 56 57 57 58

2.8

MMS Data-Type Conversions

59

P343/EN PM/J86

Page 3

PICS and MICS

MiCOM P343

TABLES
Table 1: Basic conformance statement Table 2: Models conformance statement Table 3: Service conformance statement Table 4: Logical devices definitions Table 5: Logical devices data model Table 6: Logical node definitions Table 7: Common data class definitions Table 8: MMS data-type conversions 5 6 9 10 14 16 39 59

Page 4

P343/EN PM/J86

MiCOM P343

PICS and MICS

PROTOCOL IMPLEMENTATION CONFORMANCE STATEMENT (PICS)

Introduction

1.1

This specification is the Protocol Implementation Conformance Statement (PICS) and shows the (Abstract Communication Service Interface) ACSI conformance statements as defined in Annex A of Part 7-2 of the IEC 61850 standard specifications.

1.2
Client-Server roles B11 B12 SCSMs supported B21 B22 B23 B24 B31 B32 B41 B42 Notes

ACSI Basic Conformance Statement

Client/ subscriber Server side (of Two-Party-Application-Association) Client side of (Two-Party-Application-Association) SCSM: IEC 6185-8-1 used SCSM: IEC 6185-9-1 used SCSM: IEC 6185-9-2 used SCSM: other Publisher side Subscriber side Publisher side Subscriber side Y = supported N or empty = not supported Y Y Y Y Server/ publisher Value/ comments

The basic conformance statement is defined in Table 1.

Generic Substation Event model (GSE)

Transmission of Sampled Value Model (SVC)

Table 1: Basic conformance statement

1.3

ACSI Models Conformance Statement

Client/ subscriber Server/ publisher Y Y Y Y Y Y Y Value/ comments

The ACSI models conformance statement is defined in Table 2.

If Server or Client side (B11/12) is supported M1 M2 M3 M4 M5 M6 M7 M7-1 Logical Device Logical Node Data Data set Substitution Setting group control Reporting Buffered report control sequence-number

P343/EN PM/J86

Page 5

PICS and MICS

MiCOM P343

Client/ subscriber M7-2 M7-3 M7-4 M7-5 M7-6 M7-7 M7-8 M7-9 M7-10 M7-11 M8 M8-1 M8-2 M8-3 M8-4 M8-5 M8-6 M8-7 M8-8 M8-9 M9 M9-1 M10 M11 If GSE (B31/32) is supported M12 M13 If SVC (41/42) is supported M14 M15 Multicast SVC Unicast SVC Generic Object Oriented Substation Event (GOOSE) Generic Substation Status Event (GSSE) Y Y Control Log Y report-time-stamp reason-for-inclusion data-set-name data-reference buffer-overflow entryID BufTim IntgPd GI conf-revision Unbuffered report control sequence-number report-time-stamp reason-for-inclusion data-set-name data-reference BufTim IntgPd GI conf-revision Logging Log control IntgPd Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y

Server/ publisher

Value/ comments

If Server or Client side (B11/12) is supported M16 M17 Notes Time File Transfer Y = service is supported N or empty = service is not supported Y Y Y Time source with required accuracy shall be available.

Table 2: Models conformance statement

1.4

ACSI Service Conformance Statement

The ACSI service conformance statement is defined in Table 3 (depending on the statements in Table 1).

Page 6

P343/EN PM/J86

MiCOM P343

PICS and MICS

Services Server S1 ServerDirectory

AA: TP/MC TP

Client (C)

Server (S) Y

Comments

Application association S2 S3 S4 Logical Device S5 Logical Node S6 S7 Data S8 S9 S10 S11 Data set S12 S13 S14 S15 S16 Substitution S17 SetDataValues TP GetDataSetValues SetDataSetValues CreateDataSet DeleteDataSet GetDataSetDirectory TP TP TP TP TP Y Y GetDataValues SetDataValues GetDataDirectory GetDataDefinition TP TP TP TP Y Y Y Y LogicalNodeDirectory GetAllDataValues TP TP Y Y LogicalDeviceDirectory TP Y Associate Abort Release Y Y Y

Setting group control S18 S19 S20 S21 S22 S23 Reporting Buffered Report Control Block (BRCB) S24 S24-1 Report data-change (dchg) TP Y Y SelectActiveSG SelectEditSG SetSGValues ConfirmEditSGValues GetSGValues GetSGCBValues TP TP TP TP TP TP Y Y Y

P343/EN PM/J86

Page 7

PICS and MICS

MiCOM P343

Services S24-2 S24-3 S25 S26 S27 S27-1 S27-2 S27-3 S28 S29 Logging Log control block S30 S31 Log S32 S33 S34 QueryLogByTime QueryLogByEntry GetLogStatusValues GetLCBValues SetLCBValues qchg-change (qchg) data-update (dupd) GetBRCBValues SetBRCBValues Report data-change (dchg) qchg-change (qchg) data-update (dup) GetURCBValues SetURCBValues

AA: TP/MC

Client (C)

Server (S)

Comments

TP TP TP

Y Y Y Y

Unbuffered Report Control Block (URCB)

TP TP

Y Y

TP TP TP TP TP

Generic Substation Event model (GSE) GOOSE-Control-Block S35 S36 S37 S38 S39 S40 S41 S42 S43 S44 SendGOOSEMessage GetReference GetGoCBValues SetGoCBValues SendGSSEMessage GetReference GetGSSEElementNumber GetGsCBValues SetGsCBValues MC TP TP TP MC TP TP TP TP Y Y Y IED supports GOOSE publish & subscription.

GetGOOSEElementNumber TP

GSSE-Control-Block

Transmission of Sampled Value Model (SVC) Multicast SVC S45 S46 S47 SendMSVMessage GetMSVCBValues SetMSVCBValues MC TP TP

Page 8

P343/EN PM/J86

MiCOM P343

PICS and MICS

Services Unicast SVC S48 S49 S50 Control S51 S52 S53 S54 S55 S56 File transfer S57 S58 S59 S60 Time T1 T2 Time resolution of internal clock Time accuracy of internal clock GetFile SetFile DeleteFile GetFileAttributeValues Select SelectWithValue Cancel Operate CommandTermination TimeActivated-Operate SendUSVMessage GetUSVCBValues SetUSVCBValues

AA: TP/MC TP TP TP

Client (C)

Server (S)

Comments

Y TP TP TP TP TP Y Y Y Y

TP TP TP TP

Y Only from /dr_unextracted/ Operation may only be performed on .cfg files.

Y Y

1 ms 1 ms

Nearest negative power of 2 in seconds. T0 T1 T2 T3 T4 T5

T3 Notes

Supported TimeStamp resolution

1 ms

Nearest negative power of 2 in seconds.

AA: Application association type MC: Multicast (for GOOSE and SMV) MMS: Manufacturing Message Specification TP: Two part (for MMS)

Table 3: Service conformance statement

P343/EN PM/J86

Page 9

PICS and MICS

MiCOM P343

MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)

Introduction
This specification is the Model Implementation Conformance Statement (MICS) and presents the top-level IEC 61850 data model that has been implemented. The definitions of all used Logical Nodes and their associated Common Data Classes, components and associated enumerated values are also included for completeness. You are expected to be conversant with the terminology shown in the IEC 61850 Part 7 series of specifications.

2.1

2.2

Objective
To provide comprehensive details of the standard data object model elements supported by the device. The MICS conforms to the devices associated ICD (Substation Configuration Language) file, according to Part 6 of the IEC 61850 standards. The layout of the tables shown within this document conform to the Part 7 series of the IEC 61850 standard specifications with the following exceptions: The "Trigger Options" field is not presented The "M/O" field is not present as the definitions are as deployed within the model An additional column "X" is used to signify Schneider Electric custom attributes

2.3

Logical Device Definitions

The MiCOM relay implements an IEC 61850 server that can contain one or more Logical Devices. Each Logical Device contains a data model built from instances of specific Logical Nodes and must consist of: at least an instance of the LPHD Logical Node (which is responsible for providing physical device information) and an instance of the LLN0 Logical Node (for addressing common issues across the Logical Device).

The IEC 61850 data model is contained within the Logical Devices detailed in Table 4. All MiCOM devices will name the supported Logical Devices consistently to ensure that data model variables with the same purpose will have the same name within each MiCOM server.
Logical Device Control Measurements Protection Records System P343 Control P343 Measurements P343 Protection P343 Records P343 System Comment/Usage

Table 4: Logical devices definitions

Page 10

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.3.1

IEC 61850 Logical Device Data Model

The IEC 61850 Logical Device top-level data model consists of instances of Logical Nodes. The data model name for a Logical Node instance is constructed from an optional prefix (known as the wrapper), the Logical Node name, and an instance ID (or suffix). The presented data model is in an alphabetically sorted order, rather than a logical order, because this is the natural order of the data when presented by a native MMS browser. (Higher level browsers can of course impart any ordering that they desire).
LD Control LLN0 LPHD1 XCBR1 Measurements AfqMMTR1 LLN0 LPHD1 PriFouMMXU1 PriFxdMSTA1 PriHa3MMXU1 PriLzdMDIF1 PriMMTR1 PriPkdMSTA1 PriRmsMMXU1 PriRodMSTA1 PriSenMMXU1 PriSeqMSQI1 PriStdMMXU1 PriStdMMXU2 PriVhzMMXU1 RtdGGIO1 RtrLfiMMXU1 SecFouMMXU1 SecFxdMSTA1 SecHa3MMXU1 SecLzdMDIF1 SecMMTR1 SecPkdMSTA1 SecRmsMMXU1 SecRodMSTA1 SecSenMMXU1 SecSeqMSQI1 SecStdMMXU1 SecStdMMXU2 SecVhzMMXU1 MMTR_AFQ LLN0_STANDARD LPHD_STANDARD MMXU_DERIVED_ALL MSTA_STANDARD MMXU_THIRD_HARMONIC MDIF_ALL MMTR_PRIV MSTA_STANDARD MMXU_RMS MSTA_STANDARD MMXU_SENSITIVE MSQI_ALL MMXU_STANDARD_ALL MMXU_STANDARD2_NO_VN MMXU_VHZ GGIO_ANAL_10 MMXU_ROTOR_EF MMXU_DERIVED_ALL MSTA_STANDARD MMXU_THIRD_HARMONIC MDIF_ALL MMTR_PRIV MSTA_STANDARD MMXU_RMS MSTA_STANDARD MMXU_SENSITIVE MSQI_ALL MMXU_STANDARD_ALL MMXU_STANDARD2_NO_VN MMXU_VHZ Abnormal Frequency Time measurements Measurements Logical Device Physical Device Information Primary Fourier Derived Measurands Primary Fixed demand measurements Primary Third Harmonic Measurements Primary Generator differential measurements Primary based Energy flow metering quantities Primary Peak demand measurements Primary RMS measurements Primary Rolling demand measurements Primary Sensitive power measurements Primary Sequence measurements Primary Standard Measurements all except P341 Primary Standard measurements - second CTs, No VN2 Primary Volts/Hz Measurements RTD temperature measurements Rotor EF Measurements Secondary Fourier derived measurands Secondary Fixed demand Measurements Secondary Third Harmonic Measurements Secondary Generator Differential measurements Secondary based Energy flow metering quantities Secondary Peak Demand measurements Secondary RMS measurements Secondary Rolling Demand measurements Secondary Sensitive Power measurements Secondary Sequence measurements Secondary Standard Measurements all except P341 Secondary Measurements - second CTs, No VN2 Secondary Volts/Hz Measurements LLN0_CONTROL LPHD_STANDARD XCBR_BASIC LLN0 for control LD Physical Device Information Circuit Breaker Monitoring LN Instance LN Type Description

P343/EN PM/J86

Page 11

PICS and MICS

MiCOM P343

LD Protection

LN Instance CbfRBRF1 CbfRBRF2 CliAlmPTUC1 CliAlmPTUC2 CliAlmPTUC3 CliAlmPTUC4 CliRCLI1 CliRCLI2 CliRCLI3 CliRCLI4 CliTrpPTUC1 CliTrpPTUC2 CliTrpPTUC3 CliTrpPTUC4 DifHzdPDIF1 DifIntPDIF1 DifLzdPDIF1 DmpPDMP1 EftPTOC1 EftPTOC2 FrqPTOF1 FrqPTOF2 FrqPTUF1 FrqPTUF2 FrqPTUF3 FrqPTUF4 LLN0 LPHD1 NpsPTOC1 NpsPTOC2 NpsPTOC3 NpsPTOC4 NpsPTOV1 OcpPTOC1 OcpPTOC2 OcpPTOC3 OcpPTOC4 PdpPPWR1 PdpPPWR2 PszPPAM1 PTRC1 RtdPTTR1 RtdPTTR10

LN Type RBRF_EXTTRIP RBRF_EXTTRIP PTUC_NEU PTUC_NEU PTUC_NEU PTUC_NEU RCLI_STANDARD RCLI_STANDARD RCLI_STANDARD RCLI_STANDARD PTUC_NEU PTUC_NEU PTUC_NEU PTUC_NEU PDIF_NEU PDIF_NEU PDIF_NEU PDMP_NORMAL PTOC_NO_SEG PTOC_NO_SEG PTOF_NO_SEG PTOF_NO_SEG PTUF_NO_SEG PTUF_NO_SEG PTUF_NO_SEG PTUF_NO_SEG LLN0_P343 LPHD_STANDARD PTOC_NEU PTOC_NEU PTOC_NEU PTOC_NEU PTOV_NEU PTOC_NEU PTOC_NEU PTOC_NEU PTOC_NEU PPWR_NORMAL PPWR_NORMAL PPAM_STANDARD PTRC_NO_SEG PTTR_NO_SEG PTTR_NO_SEG CB Fail 1 CB Fail 2 CLIO Input 1 Alarm CLIO Input 2 Alarm CLIO Input 3 Alarm CLIO Input 4 Alarm

Description

Current loop input supervision - channel 1 Current loop input supervision - channel 2 Current loop input supervision - channel 3 Current loop input supervision - channel 4 Current Loop Input 1 Trip Current Loop Input 2 Trip Current Loop Input 3 Trip Current Loop Input 4 Trip differential - high impedance differential - interturn differential - low impedance Dead machine Earth fault - stage 1 Earth fault - stage 2 F> 1 Overfrequency F> 2 Overfrequency F< 1 Underfrequency F< 2 Underfrequency F< 3 Underfrequency F< 4 Underfrequency LLN0 for P343 Physical Device Information NPS overcurrent - stage 1 NPS overcurrent - stage 2 NPS overcurrent - stage 3 NPS overcurrent - stage 4 NPS Overvoltage I>1Phase overcurrent I>2 Phase overcurrent I>3 Phase overcurrent I>4 Phase overcurrent Power protection (3-phase) stage 1 Power protection (3-phase) stage 2 Pole Slip / Out of Step Trip Conditioning RTD channel 1 RTD channel 10

Page 12

P343/EN PM/J86

MiCOM P343

PICS and MICS

LD

LN Instance RtdPTTR2 RtdPTTR3 RtdPTTR4 RtdPTTR5 RtdPTTR6 RtdPTTR7 RtdPTTR8 RtdPTTR9 RtdRTTR1 RtdRTTR10 RtdRTTR2 RtdRTTR3 RtdRTTR4 RtdRTTR5 RtdRTTR6 RtdRTTR7 RtdRTTR8 RtdRTTR9 RtpTrpPTTR1 RtrLfiPEFI1 RtrLfiPEFI2 SbkOcpPVOC1 SbkUzpPDIS1 SbkUzpPDIS2 SenPdpPPWR1 SenPdpPPWR2 SenRefPDIF1 SenSefPTOC1 StaHa3PTOV1 StaHa3PTUV1 SvnRVCS1 TafPTAF1 TafPTAF2 TafPTAF3 TafPTAF4 TafPTAF5 TafPTAF6 ThmPTTR1 UxpPDUP1 UxpPDUP2 VhzPVPH1 VhzPVPH2 VhzPVPH3 VhzPVPH4

LN Type PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG PTTR_NO_SEG RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD RTTR_STANDARD PTTR_NO_SEG_PRIV PEFI_NEU_UR PEFI_NEU_UR PVOC_STANDARD PDIS_SYSTEM PDIS_SYSTEM PPWR_NORMAL PPWR_NORMAL PDIF_NEU PTOC_NO_SEG PTOV_NO_SEG PTUV_NO_SEG RVCS_STANDARD PTAF_NO_SEG PTAF_NO_SEG PTAF_NO_SEG PTAF_NO_SEG PTAF_NO_SEG PTAF_NO_SEG PTTR_NO_SEG_PRIV PDUP_STANDARD PDUP_STANDARD PVPH_STANDARD PVPH_STANDARD PVPH_STANDARD PVPH_STANDARD RTD channel 2 RTD channel 3 RTD channel 4 RTD channel 5 RTD channel 6 RTD channel 7 RTD channel 8 RTD channel 9 RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision RTD Supervision

Description

Rotor Thermal - NPS Trip Rotor Earth Fault Stage 1 Alarm Rotor Earth Fault Stage 2 Trip System backup - voltage overcurrent system backup - Underimpedance stage 1 system backup - Underimpedance stage 2 Sensitive power (Single phase) stage 1 Sensitive power (Single phase) stage 2 IREF> 1 Restricted Earth Fault ISEF>1 Protection 3rd Harmonic stator Overvoltage 3rd Harmonic stator Undervoltage VTS/CTS Supervision Turbine Abnormal Frequency - Channel 1 Turbine Abnormal Frequency - Channel 2 Turbine Abnormal Frequency - Channel 3 Turbine Abnormal Frequency - Channel 4 Turbine Abnormal Frequency - Channel 5 Turbine Abnormal Frequency - Channel 6 Thermal Overload Underexcitation - stage 1 Underexcitation - stage 2 Overfluxing Overfluxing Overfluxing Overfluxing

P343/EN PM/J86

Page 13

PICS and MICS

MiCOM P343

LD

LN Instance VtpPhsPTOV1 VtpPhsPTOV2 VtpPhsPTUV1 VtpPhsPTUV2 VtpResPTOV1 VtpResPTOV2 VtpResPTOV3 VtpResPTOV4

LN Type PTOV_NO_SEG PTOV_NO_SEG PTUV_NO_SEG PTUV_NO_SEG PTOV_NO_SEG PTOV_NO_SEG PTOV_NO_SEG PTOV_NO_SEG LLN0_STANDARD LPHD_STANDARD RDRE_BASIC GGIO_ALM_96 GGIO_IND_32 GGIO_IND_32 GGIO_IND_8 LLN0_SYSTEM LPHD_STANDARD GGIO_IND_32 GGIO_IND_32 GGIO_IND_32_CTRL GGIO_IND_32

Description Phase Overvoltage - stage 1 Phase Overvoltage - stage 2 Phase Undervoltage - Stage 1 Phase Undervoltage - Stage 2 Residual Overvoltage - stage 1 Residual Overvoltage - stage 2 Residual Overvoltage - stage 3 Residual Overvoltage - stage 4 Records Logical Device Physical Device Information Disturbance Recorder Alarms GOOSE Input Signals GOOSE Output Signals 8 programmable LEDS Sys Logical Device Physical Device Information Opto Inputs (32 off) Uniqueness of control "Order Running" indications for Control operations Controllable Inputs Output Contacts (32 off)

Records LLN0 LPHD1 RDRE1 System AlmGGIO1 GosGGIO1 GosGGIO2 LedGGIO1 LLN0 LPHD1 OptGGIO1 OrdRunGGIO1 PloGGIO1 RlyGGIO1

Table 5: Logical devices data model

Page 14

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4

Logical Node Definitions

The definition tables for each of the Logical Nodes in the top-level data model are shown in individual sections. Table 6 shows a summary of the Logical Node templates used across the Logical Devices within the overall IEC 61850 product data model:
LN Type GGIO_ANAL_10 GGIO_IND_32 GGIO_IND_32_CTRL GGIO_IND_8 GGIO_ALM_96 LLN0_CONTROL LLN0_P343 LLN0_STANDARD LLN0_SYSTEM LPHD_STANDARD MDIF_ALL MMTR_AFQ MMTR_PRIV MMXU_RMS MMXU_ROTOR_EF MMXU_SENSITIVE MMXU_STANDARD_ALL MMXU_STANDARD2_NO_ VNMMXU_THIRD_HARMONIC MMXU_VHZ MMXU_DERIVED_ALL MSQI_ALL MSTA_STANDARD PDIF_NEU PDIS_SYSTEM PDMP_NORMAL PDUP_STANDARD PEFI_NEU_UR PPAM_STANDARD PPWR_NORMAL PTAF_NO_SEG (LN Class) (GGIO) (GGIO) (GGIO) (GGIO) (GGIO) (LLN0) (LLN0) (LLN0) (LLN0) (LPHD) (MDIF) (MMTR) (MMTR) (MMXU) (MMXU) (MMXU) (MMXU) (MMXU) (MMXU) (MMXU) (MMXU) (MSQI) (MSTA) (PDIF) (PDIS) (PDMP) (PDUP) (PEFI) (PPAM) (PPWR) (PTAF) Description Generic Process I/O w.r.t. 10 analogue inputs Generic Process I/O (w.r.t. 32 Indication Elements) Generic Process I/O Generic Process I/O (w.r.t. 8 Indication Elements) Generic Process I/O (w.r.t. 96 Alarm Elements) Control Domain Logical Node 0 Logical Node 0 General Logical Node 0 System Logical Node 0 Px40 Physical Device Information Differential measurements Metering Metering Measurements (RMS values) Measurements for Rotor E/F Sensitive measurements Standard measurements Standard measurements (w.r.t. Fourier Derived Values 2nd CTs) Measurements (w.r.t. 3rd Harmonic) Measurements (w.r.t. Volts Per Hz) Standard measurements Standard measurements (w.r.t. Fourier Derived Values) Differential (w.r.t. Neutral) Distance Combined Overcurrent/Undervoltage protection (Dead Machine) Underpower protection Earth Fault Injection protection - Underresistance model out-of-step protection of generators Power Protection with Pole Dead Inhibit Turbine Abnormal Frequency Protection Name Space IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 IEC 61850-7-4:2003

Sequence and imbalance (w.r.t. Pos, Neq, Zero) IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 Schneider ElectricSII:PCS-Px40

P343/EN PM/J86

Page 15

PICS and MICS

MiCOM P343

LN Type PTOC_NEU PTOC_NO_SEG PTOF_NO_SEG PTOV_NEU PTOV_NO_SEG PTRC_NO_SEG PTTR_NO_SEG PTTR_NO_SEG_PRIV PTUC_NEU PTUF_NO_SEG PTUV_NO_SEG PVOC_STANDARD PVPH_STANDARD RBRF_EXTTRIP RCLI_STANDARD RDRE_BASIC RTTR_STANDARD RVCS_STANDARD XCBR_BASIC

(LN Class) (PTOC) (PTOC) (PTOF) (PTOV) (PTOV) (PTRC) (PTTR) (PTTR) (PTUC) (PTUF) (PTUV) (PVOC) (PVPH) (RBRF) (RCLI) (RDRE) (RTTR) (RVCS) (XCBR)

Description Timed Overcurrent (w.r.t. Neutral) Overfrequency (w.r.t. No Phase Segregation) Overvoltage (w.r.t. Neutral) Overvoltage (w.r.t. Phase Segregation) Protection trip conditioning (w.r.t. No Phase Segregation) Thermal overload for Thermal State and NPS Thermal (w.r.t. No Phase Segregation) Models timed Undercurrent protection Underfrequency (w.r.t. No Phase Segregation) Undervoltage (w.r.t. No Phase Segregation) Voltage-controlled time overcurrent Volts per Hz protection Breaker Failure (w.r.t. External Tripping) Current loop monitoring and reporting

Name Space IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003

Timed Overcurrent (w.r.t. No Phase Segregation) IEC 61850-7-4:2003

Thermal overload (w.r.t. No Phase Segregation) IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-2:2003 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40 IEC 61850-7-4:2003 IEC 61850-7-4:2003 IEC 61850-7-4:2003 Schneider ElectricSII:PCS-Px40

Disturbance Recorder function (w.r.t. Mandatory IEC 61850-7-4:2003 Attributes only) Temperature monitoring and reporting VTS/CTS monitoring and report Schneider ElectricSII:PCS-Px40 Schneider ElectricSII:PCS-Px40

Circuit Breaker (w.r.t. Mandatory Attributes only) IEC 61850-7-4:2003

Table 6: Logical node definitions

Page 16

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.1

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Alm1 Alm2 Alm3 Alm4 Alm5 Alm6 Alm7 Alm8 Alm9 Alm10 Alm11 Alm12 Alm13 Alm14 Alm15 Alm16 Alm17 Alm18 Alm19 Alm20 Alm21 Alm22 Alm23 Alm24 Alm25 Alm26 Alm27 Alm28 Alm29 Alm30 Alm31 Alm32 Alm33 Alm34 Alm35 Alm36

GGIO_ALM_96

Description: Generic Process I/O (w.r.t. 96 Alarm Elements) GGIO

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D Mode Behavior Health Name Plate General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm Explanation T X

P343/EN PM/J86

Page 17

PICS and MICS

MiCOM P343

Attribute Alm37 Alm38 Alm39 Alm40 Alm41 Alm42 Alm43 Alm44 Alm45 Alm46 Alm47 Alm48 Alm49 Alm50 Alm51 Alm52 Alm53 Alm54 Alm55 Alm56 Alm57 Alm58 Alm59 Alm60 Alm61 Alm62 Alm63 Alm64 Alm65 Alm66 Alm67 Alm68 Alm69 Alm70 Alm71 Alm72 Alm73 Alm74 Alm75 Alm76 Alm77 Alm78 Alm79 Alm80

Attr. Type SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D

Explanation General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm

Page 18

P343/EN PM/J86

MiCOM P343

PICS and MICS

Attribute Alm81 Alm82 Alm83 Alm84 Alm85 Alm86 Alm87 Alm88 Alm89 Alm90 Alm91 Alm92 Alm93 Alm94 Alm95 Alm96

Attr. Type SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D

Explanation General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm General single alarm

2.4.2

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt AnIn1 AnIn2 AnIn3 AnIn4 AnIn5 AnIn6 AnIn7 AnIn8 AnIn9 AnIn10

GGIO_ANAL_10

Description: Generic Process I/O w.r.t. 10 analogue inputs GGIO

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D MV_FLOAT_D Mode Behavior Health Name Plate Analogue input point 1 Analogue input point 2 Analogue input point 3 Analogue input point 4 Analogue input point 5 Analogue input point 6 Analogue input point 7 Analogue input point 8 Analogue input point 9 Analogue input point 10 Explanation T X

P343/EN PM/J86

Page 19

PICS and MICS

MiCOM P343

2.4.3

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Ind1 Ind2 Ind3 Ind4 Ind5 Ind6 Ind7 Ind8 Ind9 Ind10 Ind11 Ind12 Ind13 Ind14 Ind15 Ind16 Ind17 Ind18 Ind19 Ind20 Ind21 Ind22 Ind23 Ind24 Ind25 Ind26 Ind27 Ind28 Ind29 Ind30 Ind31 Ind32

GGIO_IND_32

Description: Generic Process I/O (w.r.t. 32 Indication Elements) GGIO

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D Mode Behavior Health Name Plate General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) Explanation T X

Page 20

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.4

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt SPCSO1 SPCSO2 SPCSO3 SPCSO4 SPCSO5 SPCSO6 SPCSO7 SPCSO8 SPCSO9 SPCSO10 SPCSO11 SPCSO12 SPCSO13 SPCSO14 SPCSO15 SPCSO16 SPCSO17 SPCSO18 SPCSO19 SPCSO20 SPCSO21 SPCSO22 SPCSO23 SPCSO24 SPCSO25 SPCSO26 SPCSO27 SPCSO28 SPCSO29 SPCSO30 SPCSO31 SPCSO32

GGIO_IND_32_CTRL

Description: Generic Process I/O GGIO

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL SPC_CONTROL Mode Behavior Health Name Plate Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Single point controllable status output Explanation T X

P343/EN PM/J86

Page 21

PICS and MICS

MiCOM P343

2.4.5

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Ind1 Ind2 Ind3 Ind4 Ind5 Ind6 Ind7 Ind8

GGIO_IND_8

Description: Generic Process I/O (w.r.t. 8 Indication Elements) GGIO

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D SPS_D Mode Behavior Health Name Plate General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) General indication (binary input) Explanation T X

2.4.6

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt AscMod AscBeh ArcMod ArcBeh

LLN0_CONTROL

Description: Control Domain Logical Node 0 LLN0

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LLN0 INC_MOD_PRIV INS_BEH_D_PRIV INC_MOD_PRIV INS_BEH_D_PRIV Mode Behavior Health Name Plate Check Synchronization Check Synchronization Auto-Reclose Auto-Reclose Explanation T X

2.4.7

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt PdpMod PdpBeh UxpMod UxpBeh StaMod

LLN0_P343

Description: Logical Node 0 LLN0

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LLN0 INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV Mode Behavior Health Name Plate Power Protection Mode Power Protection Behavior Field Failure Mode Field Failure Behavior 100% Stator EF Mode Explanation T X

Page 22

P343/EN PM/J86

MiCOM P343

PICS and MICS

Attribute StaBeh EftMod EftBeh SenMod SenBeh FrqMod FrqBeh ThmMod PszMod ThmBeh PszBeh CbfMod CbfBeh NvdMod NvdBeh RtrMod RtrBeh VtpMod VtpBeh VphMod VphBeh DmpMod DmpBeh OcpMod OcpBeh RtdMod RtdBeh CliMod CliBeh SefMod SefBeh SbkMod SbkBeh GenMod GenBeh SvnMod SvnBeh RtpMod RtpBeh

Attr. Type INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV INC_MOD_D_PRIV INS_BEH_D_PRIV

Explanation 100% Stator EF Behavior Earth Fault 1 (Measured) Mode Earth Fault 1 (Measured) Behavior Sensitive Power Mode Sensitive Power Behavior Overfrequency/Underfrequency Mode Overfrequency/Underfrequency Behavior Thermal Overload Mode Pole Slip Mode Thermal Overload Behavior Pole Slip Behavior CB Fail Mode Circuit Breaker Fail Behavior Residual Overvoltage NVD Mode Residual Overvoltage NVD Behavior Rotor Earth Fault Mode Rotor Earth Fault Behavior Overvoltage/Undervoltage Mode Overvoltage/Undervoltage Behavior Volts/Hz Mode Volts per Hz Behavior Dead Machine Mode Dead Machine Behavior Overcurrent Mode Overcurrent Behavior RTD Inputs Mode RTD Inputs Behavior CLIO Inputs Mode CLIO Inputs Behavior SEF/REF Mode SEF/REF Behavior System Backup Mode System backup Behavior Generator Differential Mode Generator Differential Behavior Supervision function mode Supervision function behavior NPS Thermal Mode NPS Thermal Behavior

P343/EN PM/J86

Page 23

PICS and MICS

MiCOM P343

2.4.8

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt

LLN0_STANDARD

Description: General Logical Node 0 LLN0

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LLN0 Mode Behavior Health Name Plate Explanation T X

2.4.9

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt LEDRs OrdRun SyncSt

LLN0_SYSTEM

Description: System Logical Node 0 LLN0

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LLN0 SPC_CONTROL SPS_WD_PRIV SPS_WD_PRIV Mode Behavior Health Name Plate LED reset Indicate the IED is operating a control object (Order Running) Indicate time synchronization in the IED is active or inactive T X X Explanation T X

2.4.10

Logical Node:
LN Class:
Attribute PhyNam PhyHealth Proxy PwrUp

LPHD_STANDARD

Description: Px40 Physical Device Information LPHD

Attr. Type DPL_STANDARD INS_HEALTH SPS_D SPS_D Explanation Physical device name plate Physical device health Indicates if this LN is a proxy Power up detected T X

Page 24

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.11

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt OpARem OpBiasRem IREFDif IREFBias

MDIF_ALL

Description: Differential measurements MDIF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN WYE_SEG WYE_SEG_NS MV_FLOAT_NS MV_FLOAT_NS Mode Behavior Health Name Plate Remote current Remote bias IREF Diff IREF Bias Explanation T X

2.4.12

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt FBnd1Tm FBnd2Tm FBnd3Tm FBnd4Tm FBnd5Tm FBnd6Tm

MMTR_AFQ

Description: Metering MMTR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN INS_NO_TIME_NS INS_NO_TIME_NS INS_NO_TIME_NS INS_NO_TIME_NS INS_NO_TIME_NS INS_NO_TIME_NS Mode Behavior Health Name Plate Frequency Band 1 Time Frequency Band 2 Time Frequency Band 3 Time Frequency Band 4 Time Frequency Band 5 Time Frequency Band 6 Time Explanation T X

2.4.13

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt SupWh SupVArh DmdWh DmdVArh

MMTR_PRIV

Description: Metering MMTR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN BCR_PRIV BCR_PRIV BCR_PRIV BCR_PRIV Mode Behavior Health Name Plate Real energy supply (Energy flow towards bus bar) Reactive energy supply (Energy flow towards bus bar) Real energy demand (Energy flow from bus bar) Reactive energy demand (Energy flow from bus bar) Explanation T X

P343/EN PM/J86

Page 25

PICS and MICS

MiCOM P343

Attribute MTRRs

Attr. Type SPC_CTRL_PRIV

Explanation Reset Energy Measurements

X X

2.4.14

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Hz PPV PhV A A1 A2 A3 W VAr VA PF AngA AngPPV AngV AvgPF AvgWatts AvgVArs AvgVA NPSPwr VN

MMXU_DERIVED_ALL

Description: Standard measurements MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT DEL_SEG WYE_SEG WYE_SEG WYE_SEG_PHASEA WYE_RES_MAG_D WYE_RES_MAG_D WYE_SEG WYE_SEG WYE_SEG WYE_SEG WYE_SEG_NS DEL_SEG_NS WYE_SEG_NS MV_FLOAT_NS MV_FLOAT_NS MV_FLOAT_NS MV_FLOAT_NS MV_FLOAT_NS WYE_RES_ANG_D_NS Mode Behavior Health Name Plate Frequency Phase-Phase Magnitudes Phase to ground voltages Currents IN Measured In-1 derived IN-2 Derived A, B, C phase watts A, B, C phase VArs A, B, C phase VA Power Factor Current Angles Phase-Phase Angles Voltage Angle 3-phase power factor 3-phase average watts 3-phase average VArs 3-phase average VA NPS Power S2 VN Derived Magnitude Angle Explanation T X

2.4.15

Logical Node:
LN Class:
Attribute Beh Mod Health NamPlt PhV A

MMXU_RMS

Description: Measurements (RMS values) MMXU

Attr. Type INS_BEH INC_MOD INS_HEALTH LPL_LN WYE_SEG WYE_SEG Behavior Mode Health Name Plate Phase to Ground voltages RMS Current Explanation T X

Page 26

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.16

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt R CLI

MMXU_ROTOR_EF

Description: Measurements for Rotor E/F MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_NS MV_FLOAT_NS Mode Behavior Health Name Plate 64R Fault Resistance Current Loop Input Current X Explanation T X

2.4.17

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt A W PwrAng VArs

MMXU_SENSITIVE

Description: Sensitive measurements MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN WYE_SEG_PHASEA WYE_RES_MAG_NS MV_FLOAT_NS MV_FLOAT_NS Mode Behavior Health Name Plate Current Sensitive watts Power angle VArs Explanation T X

2.4.18

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt RelDifA RelBiasA VN

MMXU_STANDARD_ALL

Description: Standard measurements MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_NS MV_FLOAT_NS WYE_RES_ANG_D_NS Mode Behavior Health Name Plate IREF Diff IREF Bias VN Measured quantities Explanation T X

P343/EN PM/J86

Page 27

PICS and MICS

MiCOM P343

2.4.19

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Ct2Ang Ct2A

MMXU_STANDARD2_NO_VN

Description: Standard measurements (w.r.t. Fourier Derived Values 2nd CTs) MMXU
Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN WYE_SEG_NS WYE_SEG_NS Mode Behavior Health Name Plate CT2 angles CT2 Current Explanation T X

2.4.20

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt VN

MMXU_THIRD_HARMONIC

Description: Measurements (w.r.t. 3rd Harmonic) MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_NS Mode Behavior Health Name Plate VN 3rd Harmonic Explanation T X

2.4.21

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Vhz

MMXU_VHZ

Description: Measurements (w.r.t. Volts Per Hz) MMXU

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_NS Mode Behavior Health Name Plate Volts/Hz X Explanation T X

Page 28

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.22

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt SeqA SeqV

MSQI_ALL

Description: Sequence and imbalance (w.r.t. Pos, Neq, Zero) MSQI

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SEQ_MAG_ANG SEQ_MAG_ANG Mode Behavior Health Name Plate Positive, Negative and Zero sequence current Positive, Negative and Zero sequence voltage Explanation T X

2.4.23

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt TotRtPdp TotPdp PhApPdp

MSTA_STANDARD

Description: Standard measurements (w.r.t. Fourier Derived Values) MSTA

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT_NS MV_FLOAT_NS WYE_SEG_NS Mode Behavior Health Name Plate Total reactive power (Total Q) Total active power (Total P) Phase apparent power (S) Explanation T X

2.4.24

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Op

PDIF_NEU

Description: Differential (w.r.t. Neutral) PDIF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACT_NO_SEG Mode Behavior Health Name Plate Operate T Explanation T X

P343/EN PM/J86

Page 29

PICS and MICS

MiCOM P343

2.4.25

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PDIS_SYSTEM

Description: Distance PDIS

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.26

Logical Node:
LN Class:
Attribute Op Mod Beh Health NamPlt

PDMP_NORMAL

Description: Combined Overcurrent/Undervoltage protection (Dead Machine) PDMP

Attr. Type ACT_NO_SEG INC_MOD INS_BEH INS_HEALTH LPL_LN_P Operate Mode Behavior Health Name Plate Explanation T T X

2.4.27

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PDUP_STANDARD

Description: Underpower protection PDUP

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

Page 30

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.28

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op ResStrVal

PEFI_NEU_UR

Description: Earth Fault Injection protection - Underresistance PEFI

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P ACD_NO_SEG ACT_NO_SEG ASG_FLOAT Mode Behavior Health Name Plate Start Operate (Trip) Underresistance start value Explanation T X

2.4.29

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op Z1Str Z1Op Z2Str Z2Op

PPAM_STANDARD

Description: model out-of-step protection of generators PPAM

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG ACD_NO_SEG_NS ACT_NO_SEG_NS ACD_NO_SEG_NS ACT_NO_SEG_NS Mode Behavior Health Name Plate Start Operate Start Zone 1 Operate (Trip) Zone 1 Start Zone 2 Operate (Trip) Zone 2 T T T Explanation T X

2.4.30

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PPWR_NORMAL

Description: Power Protection with Pole Dead Inhibit PPWR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Trip T Explanation T X

P343/EN PM/J86

Page 31

PICS and MICS

MiCOM P343

2.4.31

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTAF_NO_SEG

Description: Turbine Abnormal Frequency Protection PTAF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Trip T Explanation T X

2.4.32

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTOC_NEU

Description: Timed Overcurrent (w.r.t. Neutral) PTOC

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.33

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTOC_NO_SEG

Description: Timed Overcurrent (w.r.t. No Phase Segregation) PTOC

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

Page 32

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.34

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTOF_NO_SEG

Description: Overfrequency (w.r.t. No Phase Segregation) PTOF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.35

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTOV_NEU

Description: Overvoltage (w.r.t. Neutral) PTOV

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.36

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTOV_NO_SEG

Description: Overvoltage (w.r.t. Phase Segregation) PTOV

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

P343/EN PM/J86

Page 33

PICS and MICS

MiCOM P343

2.4.37

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Tr Str

PTRC_NO_SEG

Description: Protection trip conditioning (w.r.t. No Phase Segregation) PTRC

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACT_NO_SEG ACD_NO_SEG Mode Behavior Health Name Plate Trip Sum of all starts of all connected Logical Nodes Explanation T X

2.4.38

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Op MTRRs

PTTR_NO_SEG

Description: Thermal overload (w.r.t. No Phase Segregation) PTTR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACT_NO_SEG SPC_CTRL_PRIV Mode Behavior Health Name Plate Operate Reset thermal state T X Explanation T X

2.4.39

Logical Node:

PTTR_NO_SEG_PRIV

Description: Thermal overload for Thermal State and NPS Thermal (w.r.t. No Phase Segregation) LN Class:
Attribute Mod Beh Health NamPlt TmpRl Op AlmThm MTRRs

PTTR
Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN MV_FLOAT ACT_NO_SEG ACT_NO_SEG SPC_CTRL_PRIV Mode Behavior Health Name Plate Relation between temperature and maximum temperature Operate Thermal alarm Reset Thermal State T T X Explanation T X

Page 34

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.40

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op ModOvA

PTUC_NEU

Description: Models timed Undercurrent protection PTUC

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG SPS_WD_NS Mode Behavior Health Name Plate Started Operate Overcurrent Mode Indication T Explanation T X

2.4.41

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTUF_NO_SEG

Description: Underfrequency (w.r.t. No Phase Segregation) PTUF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.42

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PTUV_NO_SEG

Description: Undervoltage (w.r.t. No Phase Segregation) PTUV

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

P343/EN PM/J86

Page 35

PICS and MICS

MiCOM P343

2.4.43

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PVOC_STANDARD

Description: Voltage-controlled time overcurrent PVOC

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.44

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Str Op

PVPH_STANDARD

Description: Volts per Hz protection PVPH

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACD_NO_SEG ACT_NO_SEG Mode Behavior Health Name Plate Start Operate T Explanation T X

2.4.45

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt OpEx

RBRF_EXTTRIP

Description: Breaker Failure (w.r.t. External Tripping) RBRF

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN ACT_NO_SEG Mode Behavior Health Name Plate Breaker failure trip ("External trip") T Explanation T X

Page 36

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.4.46

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Val Blk Min Max

RCLI_STANDARD

Description: Current loop monitoring and reporting RCLI

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P MV_FLOAT SPS_WD ASG_FLOAT ASG_FLOAT Mode Behavior Health Name Plate Current loop input measured value Block (TRUE = current loop blocked) Minimum input of current loop Maximum input of current loop Explanation T X

2.4.47

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt RcdMade FltNum

RDRE_BASIC

Description: Disturbance Recorder function (w.r.t. Mandatory Attributes only) RDRE

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPS_WD INS_BASIC Mode Behavior Health Name Plate Recording made Fault number Explanation T X

2.4.48

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt DataErr OpnCct ShrtCct HWErr

RTTR_STANDARD

Description: Temperature monitoring and reporting RTTR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P SPS_D SPS_D SPS_D SPS_D Mode Behavior Health Name Plate data error open circuit short circuit hardware error Explanation T X

P343/EN PM/J86

Page 37

PICS and MICS

MiCOM P343

2.4.49

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt SlwVTSBlk FstVTSBlk CTSBlk CTS2Blk

RVCS_STANDARD

Description: VTS/CTS monitoring and report RVCS

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN_P SPS_D SPS_D SPS_D SPS_D Mode Behavior Health Name Plate slow VTS block status fast VTS block status CTS block status CTS2 block status Explanation T X

2.4.50

Logical Node:
LN Class:
Attribute Mod Beh Health NamPlt Loc EEHealth OpCnt Pos BlkOpn BlkCls CBOpCap

XCBR_BASIC

Description: Circuit Breaker (w.r.t. Mandatory Attributes only) XCBR

Attr. Type INC_MOD INS_BEH INS_HEALTH LPL_LN SPS_WD INS_HEALTH INS_BASIC DPC_STATUS SPC_STATUS SPC_STATUS INS_HEALTH Mode Behavior Health Name Plate Local operation External equipment health Operation counter Switch position Block opening Block closing Circuit Breaker operating capability Explanation T X

Page 38

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5

Common Data Class Definitions

The definition tables for each of the Common Data Classes used in the Logical Node definitions are presented in the following sub-sections. From an application point-of-view the data attributes of a Common Data Class are classified according to their specific use. The characterization of data attributes, and the services that they support/provide, is done by using 'Functional Constraints'. The Functional Constraints are specified in Table 7:
FC Name BR CF CO DC EX GO GS LG MS MX RP SE SG SP ST SV US XX Buffered reports Configuration Control Description Extended Definition GOOSE Control GSSE Control (UCA2 GOOSE) Logging Multicast sampled value control Measurands (Analogue values) Unbuffered reports Setting Group Editable Setting Group Set Point Status Information Substitution Values Unicast sampled value control Data attribute service parameters Semantic Source Definition IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2 IEC 61850-7-2

Table 7: Common data class definitions

P343/EN PM/J86

Page 39

PICS and MICS

MiCOM P343

2.5.1

Common Data Class:

CDC Class: ACD

ACD_NO_SEG

Description: Directional Protection Activation Information (w.r.t. No Phase Segregation)

Attribute general dirGeneral q t

Type BOOLEAN ENUMERATED8 (MMS Type: INT8) Quality TimeStamp ST ST ST ST

FC

Enumeration

Comment Trip or start has happened General direction (unknown, forward, backward or both) Quality of the protection activation information Timestamp of the last change in state of protection activation information

dir

2.5.2

Common Data Class:

CDC Class: ACD

ACD_NO_SEG_NS

Description: ACD_NO_SEG with namespace DO dataNs

Attribute general dirGeneral q t dataNs

Type BOOLEAN ENUMERATED8 (MMS Type: INT8) Quality TimeStamp VISIBLE_STRING255 ST ST ST ST EX

FC

Enumeration

Comment Trip or start has happened General direction (unknown, forward, backward or both) Quality of the protection activation information Timestamp of the last change in state of protection activation information Data name space

dir

2.5.3

Common Data Class:

CDC Class: ACT

ACT_NO_SEG

Description: Protection Activation Information (w.r.t. No Phase Segregation)

Attribute general q t

Type BOOLEAN Quality TimeStamp ST ST ST

FC

Enumeration

Comment Trip or start has happened Quality of the protection activation information Timestamp of the last change in state of protection activation information

Page 40

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.4

Common Data Class:

CDC Class: ACT

ACT_NO_SEG_NS

Description: ACT_NO_SEG with namespace DO dataNs

Attribute general q t dataNs

Type BOOLEAN Quality TimeStamp VISIBLE_STRING255 ST ST ST EX

FC

Enumeration

Comment Trip or start has happened Quality of the protection activation information Timestamp of the last change in state of protection activation information Data name space

2.5.5

Common Data Class:

CDC Class: ASG

ASG_FLOAT

Description: Analogue Setting

Attribute setMag d units

Type AnalogueValue_Float VISIBLE_STRING255 Unit_multiplier SE

FC DC CF

Enumeration Setting value

Comment Description of the status element Unit of the attribute representing the data

2.5.6

Common Data Class:

CDC Class: BCR

BCR_PRIV

Description: Binary Counter Reading

Attribute actVal q t pulsQty INT128 Quality

Type ST ST ST CF

FC

Enumeration

Comment Binary counter status represented as an integer Quality of counter value Time of last counter change Magnitude of the counted value 'per count' (value = actVal x pulsQty)

TimeStamp FLOAT32

P343/EN PM/J86

Page 41

PICS and MICS

MiCOM P343

2.5.7

Common Data Class:

CDC Class: CMV

CMV_MAG_ANG_FLOAT

Description: Complex Measured value (w.r.t. Floating Point Magnitude and Angle)

Attribute

Type

FC

Enumeration

Comment Deadbanded complex measured vector. Updated to the current value of instCVal when the value has changed according to the configuration parameter db. Quality of the measurement value Time deadbanded magnitude last exceeded its db configuration parameter Unit of the attribute representing the data Measurement deadband Measurement range configuration attributes

cVal

Vector_MagnitudeAngle_Float

MX

q t units db rangeC

Quality TimeStamp Unit_multiplier INT32U RangeConfig_Deadband

MX MX CF CF CF

2.5.8

Common Data Class:

CDC Class: CMV

CMV_MAG_FLOAT

Description: Complex Measured value (w.r.t. Floating Point Magnitude)

Attribute cVal q t units db rangeC

Type Vector_Magnitude_Float Quality TimeStamp Unit_multiplier INT32U RangeConfig_Deadband

FC MX MX MX CF CF CF

Enumeration

Comment Deadbanded complex measured vector. Updated to the current value of instCVal when the value has changed according to the configuration parameter db. Quality of the measurement value Time deadbanded magnitude last exceeded its db configuration parameter Unit of the attribute representing the data Measurement deadband Measurement range configuration attributes

Page 42

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.9

Common Data Class:

DEL_SEG

Description: Phase to phase measurements for a 3-Phase system (w.r.t. Phase Segregation) CDC Class: DEL
Attribute phsAB phsBC phsCA Type CMV_MAG_FLOAT CMV_MAG_FLOAT CMV_MAG_FLOAT ---FC Enumeration Comment Measurement values for Phase A to Phase B Measurement values for Phase B to Phase C Measurement values for Phase C to Phase A X

2.5.10

Common Data Class:

CDC Class: DEL

DEL_SEG_NS

Description: DEL_SEG with namespace DO dataNs

Attribute phsAB phsBC phsCA dataNs

Type CMV_MAG_FLOAT CMV_MAG_FLOAT CMV_MAG_FLOAT VISIBLE_STRING255 ---EX

FC

Enumeration

Comment Measurement values for Phase A to Phase B Measurement values for Phase B to Phase C Measurement values for Phase C to Phase A Data name space

2.5.11

Common Data Class:

CDC Class: DPC

DPC_STATUS

Description: Controllable Double Point (w.r.t. Status only)

Attribute stVal q t ctlModel

Type CODED_ENUM (MMS Type: _BSTR2) Quality TimeStamp ENUMERATED8 (MMS Type: INT8) ST ST ST CF

FC

Enumeration Dbpos

Comment Status value of the data (Intermediate state, Off, On or Bad-state) Quality of the status value Timestamp of the last change in state of status value

ctlModel

Control model (Corresponding to the behavior of the data)

P343/EN PM/J86

Page 43

PICS and MICS

MiCOM P343

2.5.12

Common Data Class:

CDC Class: DPL

DPL_STANDARD

Description: Standard Device Name Plate

Attribute vendor hwRev swRev serNum model location

Type VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255

FC DC DC DC DC DC DC

Enumeration

Comment Name of the vendor Hardware revision Software revision Serial Number Model Number Physical location of device

2.5.13

Common Data Class:

CDC Class: INC

INC_MOD

Description: Controllable Integer Status (w.r.t. Mode)

Attribute stVal q t ctlModel Quality

Type INT32 (MMS Type: INT8) ST ST ST CF

FC

Enumeration Mod

Comment Status value of the data Quality of the status value Timestamp of the last change in state of status value

TimeStamp ENUMERATED8 (MMS Type: INT8)

ctlModel

Control model (Corresponding to the behavior of the data)

2.5.14

Common Data Class:

CDC Class: INC

INC_MOD_D_PRIV

Description: Controllable Integer Status (w.r.t. Mode, with description (Private DO))

Attribute ctlVal stVal q t ctlModel d dataNs INT32

Type INT32 (MMS Type: INT8) Quality TimeStamp ENUMERATED8 (MMS Type: INT8) VISIBLE_STRING255 VISIBLE_STRING255 ST ST ST CF

FC CO

Enumeration Control value Mod

Comment Status value of the data Quality of the status value Timestamp of the last change in state of status value

ctlModel

Control model (Corresponding to the behavior of the data) Description of the status element Data name space

DC EX

Page 44

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.15

Common Data Class:

CDC Class: INC

INC_MOD_PRIV

Description: Controllable Integer Status (w.r.t. Mode (Private DO))

Attribute stVal q t ctlModel dataNs Quality

Type INT32 (MMS Type: INT8) ST ST ST CF EX

FC

Enumeration Mod

Comment Status value of the data Quality of the status value Timestamp of the last change in state of status value

TimeStamp ENUMERATED8 (MMS Type: INT8) VISIBLE_STRING255

ctlModel

Control model (Corresponding to the behavior of the data) Data name space

2.5.16

Common Data Class:

CDC Class: INS

INS_BASIC

Description: Integer Status (w.r.t. Mandatory Options only)

Attribute stVal q t INT32 Quality

Type ST ST ST

FC

Enumeration

Comment The element status The quality of the status value Timestamp of the last change in state

TimeStamp

2.5.17

Common Data Class:

CDC Class: INS

INS_BEH

Description: Integer Status (w.r.t. Behavior)

Attribute stVal q t Quality

Type INT32 (MMS Type: INT8) TimeStamp ST ST ST

FC

Enumeration Beh

Comment The element status The quality of the status value Timestamp of the last change in state

2.5.18

Common Data Class:

CDC Class: INS

INS_BEH_D_PRIV

Description: Integer Status (w.r.t. Behavior, with Description (Private DO))

Attribute stVal q t d dataNs Quality

Type INT32 (MMS Type: INT8) TimeStamp VISIBLE_STRING255 VISIBLE_STRING255 ST ST ST

FC

Enumeration Beh

Comment The element status The quality of the status value Timestamp of the last change in state Description of the status element Data name space

DC EX

P343/EN PM/J86

Page 45

PICS and MICS

MiCOM P343

2.5.19

Common Data Class:

CDC Class: INS

INS_HEALTH

Description: Integer Status (w.r.t. health)

Attribute stVal q t Quality

Type INT32 (MMS Type: INT8) TimeStamp ST ST ST

FC

Enumeration Health

Comment The element status The quality of the status value Timestamp of the last change in state

2.5.20

Common Data Class:

CDC Class: INS

INS_NO_TIME_NS

Description: Integer Status with no timestamp but with dataNs

Attribute stVal q t dataNs INT32 Quality

Type ST ST ST EX

FC

Enumeration

Comment The element status The quality of the status value Timestamp of the last change in state Data name space

TimeStamp VISIBLE_STRING255

2.5.21

Common Data Class:

CDC Class: LPL

LPL_LLN0

Description: Logical Node 0 Name Plate

Attribute vendor swRev d configRev ldNs

Type VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255

FC DC DC DC DC EX

Enumeration

Comment Name of the vendor Software revision Description Uniquely identifies the configuration of a local device instance Logical Device name space

2.5.22

Common Data Class:

CDC Class: LPL

LPL_LN

Description: Standard Logical Node Name Plate

Attribute vendor swRev d

Type VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255

FC DC DC DC

Enumeration

Comment Name of the vendor Software revision Description

Page 46

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.23

Common Data Class:

CDC Class: LPL

LPL_LN_P

Description: Logical Node Name Plate for Propriety LN

Attribute vendor swRev d lnNs

Type VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255 VISIBLE_STRING255

FC DC DC DC EX

Enumeration

Comment Name of the vendor Software revision Description Logical Node name space

2.5.24

Common Data Class:

CDC Class: MV

MV_FLOAT

Description: Measured value (w.r.t. Floating Point value)

Attribute

Type

FC

Enumeration

Comment Deadbanded magnitude of the instantaneous value of a measured value or harmonic value. Updated to the current value of instMag when the value has changed according to the configuration parameter db. Quality of the measurement value Time deadbanded magnitude last exceeded its db configuration parameter Unit of the attribute representing the data Measurement deadband Measurement range configuration attributes

mag

AnalogueValue_Float

MX

q t units db rangeC

Quality TimeStamp Unit_multiplier INT32U RangeConfig_Deadband

MX MX CF CF CF

P343/EN PM/J86

Page 47

PICS and MICS

MiCOM P343

2.5.25

Common Data Class:

CDC Class: MV

MV_FLOAT_D

Description: Measured value (w.r.t. Floating Point Value with Description)

Attribute

Type

FC

Enumeration

Comment Deadbanded magnitude of the instantaneous value of a measured value or harmonic value. Updated to the current value of instMag when the value has changed according to the configuration parameter db. Quality of the measurement value Time deadbanded magnitude last exceeded its db configuration parameter Unit of the attribute representing the data Measurement deadband Measurement range configuration attributes Description of the status element

mag

AnalogueValue_Float

MX

q t units db rangeC d

Quality TimeStamp Unit_multiplier INT32U RangeConfig_Deadband VISIBLE_STRING255

MX MX CF CF CF DC

2.5.26

Common Data Class:

CDC Class: MV

MV_FLOAT_NS

Description: MV_FLOAT with dataNs for extra Dos

Attribute

Type

FC

Enumeration

Comment Deadbanded magnitude of the instantaneous value of a measured value or harmonic value. Updated to the current value of instMag when the value has changed according to the configuration parameter db. Quality of the measurement value Time deadbanded magnitude last exceeded its db configuration parameter Unit of the attribute representing the data Measurement deadband Measurement range configuration attributes Data name space

mag

AnalogueValue_Float

MX

q t units db rangeC dataNs

Quality TimeStamp Unit_multiplier INT32U RangeConfig_Deadband VISIBLE_STRING255

MX MX CF CF CF EX

Page 48

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.27

Common Data Class:

SEQ_MAG_ANG

Description: Sequence components of a measurement value (w.r.t. Magnitudes + Angles) CDC Class: SEQ
Attribute c1 c2 c3 seqT Type CMV_MAG_ANG_FLOAT CMV_MAG_ANG_FLOAT CMV_MAG_ANG_FLOAT ENUMERATED8 (MMS Type: INT8) ---MX seqT FC Enumeration Comment Sequence component 1 (For semantic meaning see seqT) Sequence component 2 (For semantic meaning see seqT) Sequence component 3 (For semantic meaning see seqT) Sequence quantity measurement type (Pos-Neg-Zero or Dir-Quad-Zero) X

2.5.28

Common Data Class:

CDC Class: SPC

SPC_CONTROL

Description: Controllable Single Point

Attribute ctlVal origin ctlModel stVal q t sboTimeout

Type BOOLEAN Originator ENUMERATED8 (MMS Type: INT8) BOOLEAN Quality TimeStamp INT32U

FC CO ST CF ST ST ST CF

Enumeration

Comment Control value (Off - FALSE, On - TRUE) Originator of the last change of the controllable data

ctlModel

Control model (Corresponding to the behavior of the data) Status value of the data Quality of the status value Timestamp of the last change in state of status value Select Before Operate timeout period (in milliseconds)

P343/EN PM/J86

Page 49

PICS and MICS

MiCOM P343

2.5.29

Common Data Class:

CDC Class: SPC

SPC_CTRL_PRIV

Description: Controllable Single Point

Attribute ctlVal origin ctlModel stVal q t sboTimeout dataNs

Type BOOLEAN Originator ENUMERATED8 (MMS Type: INT8) BOOLEAN Quality TimeStamp INT32U VISIBLE_STRING255

FC CO ST CF ST ST ST CF EX

Enumeration

Comment Control value (Off - FALSE, On - TRUE) Originator of the last change of the controllable data

ctlModel

Control model (Corresponding to the behavior of the data) Status value of the data Quality of the status value Timestamp of the last change in state of status value Select Before Operate timeout period (in milliseconds) Data name space

2.5.30

Common Data Class:

CDC Class: SPC

SPC_STATUS

Description: Controllable Single Point (w.r.t. Status only)

Attribute stVal q t ctlModel Quality

Type BOOLEAN ST ST ST CF

FC

Enumeration

Comment Status value of the data Quality of the status value Timestamp of the last change in state of status value

TimeStamp ENUMERATED8 (MMS Type: INT8)

ctlModel

Control model (Corresponding to the behavior of the data)

2.5.31

Common Data Class:

CDC Class: SPS

SPS_D

Description: Standard Single Point Status (with Description)

Attribute stVal q t d Quality

Type BOOLEAN TimeStamp VISIBLE_STRING255 ST ST ST

FC

Enumeration

Comment The element status (TRUE or FALSE) The quality of the status value Timestamp of the last change in state Description of the status element

DC

Page 50

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.5.32

Common Data Class:

CDC Class: SPS

SPS_WD

Description: Single Point Status (without Description)

Attribute stVal q t Quality

Type BOOLEAN TimeStamp ST ST ST

FC

Enumeration

Comment The element status (TRUE or FALSE) The quality of the status value Timestamp of the last change in state

2.5.33

Common Data Class:

CDC Class: SPS

SPS_WD_NS

Description: Single Point Status (without Description, with namespace)

Attribute stVal q t dataNs Quality

Type BOOLEAN TimeStamp VISIBLE_ STRING255 ST ST ST EX

FC

Enumeration

Comment The element status (TRUE or FALSE) The quality of the status value Timestamp of the last change in state Data name space

2.5.34

Common Data Class:

CDC Class: SPS

SPS_WD_PRIV

Description: Single Point Status

Attribute stVal q t dataNs Quality

Type BOOLEAN TimeStamp VISIBLE_STRING255 ST ST ST EX

FC

Enumeration

Comment The element status (TRUE or FALSE) The quality of the status value Timestamp of the last change in state Data name space

2.5.35

Common Data Class:

WYE_RES_ANG_D_NS

Description: Phase to ground measurements for a 3-Phase system (w.r.t. Residual + Description + Angle) CDC Class: WYE
Attribute res d dataNs Type CMV_MAG_ANG_FLOAT VISIBLE_STRING255 VISIBLE_STRING255 -DC EX FC Enumeration Comment Measurement values for the residual system current Description of the status element Data name space X

P343/EN PM/J86

Page 51

PICS and MICS

MiCOM P343

2.5.36

Common Data Class:

CDC Class: WYE

WYE_RES_MAG_D

Description: Phase to ground measurements for a 1-Phase system, magnitude only

Attribute res d

Type CMV_MAG_FLOAT VISIBLE_STRING255 --

FC

Enumeration

Comment Measurement values for the residual system current Description of the status element

DC

2.5.37

Common Data Class:

CDC Class: WYE

WYE_RES_MAG_NS

Description: Phase to ground measurements for a 1-Phase system, magnitude only

Attribute res dataNs

Type CMV_MAG_FLOAT VISIBLE_STRING255 -EX

FC

Enumeration

Comment Measurement values for the residual system current Data name space

2.5.38

Common Data Class:

WYE_SEG

Description: Phase to ground measurements for a 3-Phase system (w.r.t. Phase Segregation) CDC Class: WYE
Attribute phsA phsB phsC Type CMV_MAG_FLOAT CMV_MAG_FLOAT CMV_MAG_FLOAT ---FC Enumeration Comment Measurement values for Phase A Measurement values for Phase B Measurement values for Phase C X

2.5.39

Common Data Class:

CDC Class: WYE

WYE_SEG_NS

Description: WYE_SEG with dataNs DO

Attribute phsA phsB phsC dataNs

Type CMV_MAG_FLOAT CMV_MAG_FLOAT CMV_MAG_FLOAT VISIBLE_STRING255 ---EX

FC

Enumeration

Comment Measurement values for Phase A Measurement values for Phase B Measurement values for Phase C Data name space

2.5.40

Common Data Class:

CDC Class: WYE

WYE_SEG_PHASEA

Description: Phase to ground measurements for a 3-Phase system

Attribute phsA

Type CMV_MAG_ANG_FLOAT --

FC

Enumeration

Comment Measurement values for Phase A

Page 52

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.6

Common Data Attribute Type Definitions

Common data attribute types, known herein as components, are defined for use in the Common Data Classes defined in Section 0.

2.6.1

Component:
Comment:

AnalogueValue_Float

General analogue value (w.r.t. Floating Point value)

Parent Type: AnalogueValue

Attribute f Type FLOAT32 Enumeration Floating point value Comment X

2.6.2

Component:
Comment: Parent Type:

Originator

Originator of the last change of data attribute representing the value of a controllable data object

Attribute orIdent orCat

Type OCTET_STRING64 ENUMERATED8 (MMS Type: INT8)

Enumeration

Comment Originator identification (Null value indicates unknown or not reported)

orCategory

Originator category (Not-supported, bay-control, stationcontrol, remote-control, automatic-bay, automatic-station, automatic-remote, maintenance or process)

2.6.3

Component:
Comment:

RangeConfig_Deadband

Measurement range configuration

Parent Type: RangeConfig

Attribute min max llLim lLim hLim hhLim Type AnalogueValue_Float AnalogueValue_Float AnalogueValue_Float AnalogueValue_Float AnalogueValue_Float AnalogueValue_Float Enumeration Comment Minimum process measurement for which values of i and f are considered within limits Maximum process measurement for which values of i and f are considered within limits Low Low range limit Low range limit High range limit High High range limit X

2.6.4

Component:
Comment: Parent Type: Unit

Unit_multiplier

SI Unit definitions

Attribute SIUnit multiplier

Type ENUMERATED16 (MMS Type: INT8) ENUMERATED16 (MMS Type: INT8)

Enumeration SIUnit multiplier SI Unit

Comment

Multiplier value, the default of which is 0 (i.e. multiplier = 1)

P343/EN PM/J86

Page 53

PICS and MICS

MiCOM P343

2.6.5

Component:
Comment: Parent Type: Vector

Vector_Magnitude_Float

Complex vector (w.r.t. Floating Point Magnitude value)

Attribute mag

Type AnalogueValue_Float

Enumeration

Comment The magnitude of the complex value

2.6.6

Component:
Comment: Parent Type: Vector

Vector_MagnitudeAngle_Float

Complex vector (w.r.t. Floating Point Magnitude and Angle values)

Attribute mag ang

Type AnalogueValue_Float AnalogueValue_Float

Enumeration

Comment The magnitude of the complex value The angle of the complex value (the unit is degrees)

Page 54

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.7

Enumerated Type Definitions

The following sub-sections specify the enumerations that are associated to some Common Data Class attributes. The definition of the enumerations are according to IEC 61850-7-3 and IEC 61850-7-4 unless otherwise stated.

2.7.1

Enumerated Type: AddCause

Description:
Ordinal 0 1 2 3 4 5 6 7 8 9 Unknown Not-supported Blocked-by-switching-hierarchy Select-failed Invalid-position Position-reached Parameter-change-in-execution Step-limit Blocked-by-Mode Blocked-by-process

Add Cause
Semantic Ordinal 10 11 12 13 14 15 16 17 18 Semantic Blocked-by-interlocking Blocked-by-synchrocheck Command-already-in-execution Blocked-by-health 1-of-n-control Abortion-by-cancel Time-limit-over Abortion-by-trip Object-not-selected

2.7.2

Enumerated Type: Beh

Description:
Ordinal 1 2 3 on blocked test

Behavior
Semantic Ordinal 4 5 off Semantic test/blocked

2.7.3

Enumerated Type: Bypass

Description:
Ordinal 0 1 2

Bypass
Semantic Ordinal 3 4 5 Semantic uniqueness-bypass select-bypass status-bypass

locking-bypass mode-bypass automation-bypass

2.7.4

Enumerated Type: ctlModel

Description:
Ordinal 0 1 2 status-only direct-with-normal-security sbo-with-normal-security

Control Model
Semantic Ordinal 3 4 Semantic direct-with-enhanced-security sbo-with-enhanced-security

P343/EN PM/J86

Page 55

PICS and MICS

MiCOM P343

2.7.5

Enumerated Type: Dbpos

Description:
Ordinal 0 1 off

Circuit Breaker position

Semantic Ordinal 2 3 on bad Semantic

intermediate

2.7.6

Enumerated Type: dir

Description:
Ordinal 0 1 unknown forward

Direction
Semantic Ordinal 2 3 backward both Semantic

2.7.7

Enumerated Type: Health

Description:
Ordinal 1 2 Ok Warning

Health
Semantic 3 Ordinal Alarm Semantic

2.7.8

Enumerated Type: Mod

Description:
Ordinal 1 2 3 on blocked test

Mode
Semantic Ordinal 4 5 off Semantic test/blocked

2.7.9

Enumerated Type: multiplier

Description:
Ordinal -24 -21 -18 -15 -12 -9 -6 -3 -2 -1 0 y z a f p n m c d

Exponents of the multiplier value in base 10.

Semantic 1 2 3 6 9 12 15 18 21 24 Ordinal da h k M G T P E Z Y Semantic

Page 56

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.7.10

Enumerated Type: orCategory

Description:
Ordinal 0 1 2 3 4 bay-control station-control remote-control automatic-bay

or Category
Semantic Ordinal 5 6 7 8 Semantic automatic-station automatic-remote maintenance process

not-supported

2.7.11

Enumerated Type: seqT

Description:
Ordinal 0

Sequence Measurement Type

Semantic Ordinal 1 Semantic dir-quad-zero

pos-neg-zero

P343/EN PM/J86

Page 57

PICS and MICS

MiCOM P343

2.7.12

Enumerated Type: SIUnit

Description:
Ordinal -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 1 2 3 4 5 6 7 8 9 10 11 21 22 23 24 25 26 27 28 29 30 years months weeks V/s mins hours days F ratio miles inches feet df/dt Hz/s % pu none m kg s A K mol cd deg rad sr Gy q C Sv F C S H V ohm

SI Units derived from ISO/IEC 1000

Semantic Ordinal 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 50 51 52 53 54 61 62 63 64 65 66 67 68 69 70 71 72 73 74 J N Hz lx Lm Wb T W Pa m m m/s m/s m/s m/m M kg/m m/s W/m K J/K ppm 1/s rad/s VA Watts VAr phi cos(phi) Vs V As A At VAh Wh VArh V/Hz Semantic

Page 58

P343/EN PM/J86

MiCOM P343

PICS and MICS

2.8

MMS Data-Type Conversions

Table 8 shows the relationships between the Part 7 and Part 8-1 data types. The definitions shown in Table 7 use Part 7 data types, however these are subject to 'translation' when exposed over an MMS (Part 8-1) interface:
Part 7 Type BOOLEAN BSTR16 BVstring13 Check CODED_ENUM CODED_ENUM2 EntryTime ENUMERATED16 ENUMERATED8 FLOAT32 FLOAT64 INT128 INT16 INT16U INT24U INT32 INT32U INT8 INT8U OCTET_STRING6 OCTET_STRING64 OCTET_STRING8 Quality TimeStamp UNICODE_STRING255 UTC_TM VISIBLE_STRING255 VISIBLE_STRING64 VISIBLE_STRING65 VISIBLE_STRING97 Bool Bstring16 BVstring13 BVstring2 Byte Byte Btime6 Short Byte Float Double Int64 Short Ushort Ulong Long Ulong Byte Ubyte Ostring6 OVstring64 OVstring8 BVstring13 Utctime UTF8Vstring255 Utctime Vstring255 Vstring64 Vstring65 Vstring97 MMS Type Bit String 16 Variable bit string (up to 13 bits) Control Object check flags Coded enumeration Coded enumeration (2) 8.1 Section 8.1.3.7 16-bit enumerated value 8-bit enumerated value 32-bit floating point value 64-bit floating point value 128-bit signed integer value 16-bit signed integer value 16-bit unsigned integer value 24-bit unsigned integer value 32-bit signed integer value 32-bit unsigned integer value 8-bit signed integer value 8-bit unsigned integer value 6-character string (8-bits per character) 64-character string (8-bits per character) 8-character string (8-bits per character) IEC 61850 Quality IEC 61850 Time stamp 255-character string (16-bits per Unicode character) UTC Timestamp 255-character string 64-character string 65-character string 97-character string Part 7 Description Logical TRUE/FALSE value

Table 8: MMS data-type conversions

P343/EN PM/J86

Page 59

PICS and MICS

MiCOM P343

Notes:

Page 60

P343/EN PM/J86

Customer Care Centre

http://www.schneider-electric.com/CCC

Schneider Electric 35 rue Joseph Monier 92506 Rueil-Malmaison FRANCE Phone: Fax: +33 (0) 1 41 29 70 00 +33 (0) 1 41 29 71 00 Publisher: Schneider Electric June 2011

www.schneider-electric.com Publication: P343/EN PM/J86

2011 Schneider Electric. All rights reserved.