Technical information
REWOQUAT WE 45
Structure REWOQUAT WE 45 exhibits a pleasant and soft hand, good rewet, and a noticeably reduced static charge. Fabrics treated with REWOQUAT WE 45 show a significantly reduced drying time compared to untreated fabrics. Key Features and Benefits Softening Formulations containing REWOQUAT WE 45 impart good softness to fabrics and textiles without adversely affecting the fabrics ability to absorb water. Dispersibility REWOQUAT WE 45 is designed to be handled with minimal heating. Dispersions up to 20% can be readily prepared at ambient conditions. It is recommended that REWOQUAT WE 45 be mixed thoroughly before use. Antistatic - REWOQUAT WE 45 imparts good antistatic properties to cotton and synthetic fabrics. Biodegradable The active component of REWOQUAT WE 45 is readily biodegradable according to OECD 301B. Storage and Handling This product is susceptible to darkening if stored at temperatures exceeding 60 C (140 F) for prolonged periods. Storage tanks should be equipped with heating and agitation to prevent possible separation.
Fatty Acid: C16, C18, C18 Chemistry N,N-di(alkylcarboxyethyl)-N-hydroxyethyl-Nmethylammonium methyl sulfate (chemical name). Description REWOQUAT WE 45 is a quaternary ammonium compound used in consumer and commercial laundry applications for rinse cycle fabric softeners. It is supplied at 86% active in ethanol.
Typical Properties
Appearance @ 25 C (77 F) Color Quaternary pH (5% active solution) Ethanol Density Pumping Temperature Flash Point Viscosity Molecular Weight CAS Number Application REWOQUAT WE 45 is a biodegradable TEA esterquat for use in fabric softener formulations ranging from 5 to 20%. Laundry treated with Clear or hazy liquid Light yellow 84-88% 3-5 ~ 14% ~ 0.993 g/cm3 @ 23 C (73 F) 25 C (77 F) minimum
24 C (76 F) 240 cP @ 23 C (73 F)
~ 720 g/mol 157905-74-3
Storage temperature
Drums Bulk 30 C (90 F) 40 C (104 F)
Process within
---
Evonik Industries AG | Rewoquat | February 2012 Page 1/3
Registration Status REWOQUAT WE 45 is registered on the following inventories: TSCA DSL AICS ECL
Preparation: Heat the water to approximately 25 C. Add dye and antifoam if required. Slowly disperse in REWOQUAT WE 45, preheated to approximately 25 C. Stir for about 10 minutes and add fragrance. If necessary, adjust to the required final viscosity with CaCl2. The stability and viscosity of the finished dispersion will be affected by water quality, mixing conditions, temperature, pH, and additives. Fabric Softener (18%)
Hazardous goods classification Please refer to our material safety data sheet for information concerning: Classification and labelling according to regulations for transport and for dangerous substances Protective measures for storage and handling Measures in case of accidents and fire Toxicity and ecological effects
REWOQUAT WE 45 Water Fragrance CaCl2 Dye
20.93% to 100% 0.70% 0.20 - 0.70%
Biodegradability The active component of REWOQUAT WE 45 is readily biodegradable.
Formulations Typical fabric softener fromulations for home laundry use will contain from 6% to 23% REWOQUAT WE 45, or 5% to 20% active quaternary. Stable aqueous dispersions are easy to prepare. REWOQUAT WE 45 can be used at lower temperatures than conventional TEA Ester Quats, however, the product should be thoroughly mixed before use. Mixing equipment should be 316 stainless steel, glass-lined, or chemical resistant polyester. Aluminum and mild steel should be avoided. Fabric Softener (10%) REWOQUAT WE 45 Water Fragrance CaCl2 Dye 11.63% to 100% 0.20% 0.00 0.20%
Preparation: Heat the water to approximately 25 C. Add dye and antifoam if required. Slowly disperse in REWOQUAT WE 45, preheated to approximately 25 C, adding CaCl2 solution as needed to maintain a good processing viscosity. Stir for about 10 minutes then add fragrance. Adjust to the required final viscosity with CaCl2. The stability and viscosity of the finished dispersion will be affected by water quality, mixing conditions, temperature, pH, and additives. Water Quality - Hard, soft, or deionized water may be used. Both deionized water and soft water tend to produce more viscous dispersions, but viscosity may be controlled by the addition of small amounts of calcium chloride, sodium chloride or sodium acetate (about 0.01% to about 1.0%). Partial deionization may be the most satisfactory procedure in certain areas of the country that have unusually high amounts of total dissolved salts. A salting out effect can take place in these extreme cases and result in dispersion instability. Mixing Conditions - Viscosity depends on the type of equipment used, the rate and time of agitation, and temperature conditions. Agitation should be sufficient to give a thin, stable dispersion, and air entrapment should be kept to a minimum.
Temperature - In general, a dispersion of lower viscosity is obtained with higher water temperatures. REWOQUAT WE 45 should be homogenized thoroughly before dispersion into water. pH TEA Ester Quat formulations are inherently acidic. Formulations will become unstable if excess caustic is added. The preferred pH range is from about 3 to 4. Optional Formulation Additives - Other ingredients in the formulation such as fragrance and preservatives can have an effect on dispersion and viscosity stability. Before establishing a full production method, an evaluation of the effects of additives should be completed.
Trademark and Legal Notice This information and all further technical advice is based on our present knowledge and experience. However, it implies no liability or other legal responsibility on our part, including with regard to existing third party intellectual property rights, especially patent rights. In particular, no warranty, whether express or implied, or guarantee of product properties in the legal sense is intended or implied. We reserve the right to make any changes according to technological progress or further developments. The customer is not released from the obligation to conduct careful inspection and testing of incoming goods. Performance of the product described herein should be verified by testing, which should be carried out only by qualified experts in the sole responsibility of a customer. Reference to trade names used by other companies is neither a recommendation, nor does it imply that similar products could not be used.
Evonik Goldschmidt Corporation 710 South 6th Avenue Hopewell VA 23860-5261 USA Phone +1 804 451 8658 Fax +1 804 584 8689 Evonik Degussa (China) Co. Ltd. Shanghai Branch 55 Chundong Road, Xinzhuang Industry Park, Shanghai, China 201108 Phone +86 21 6119 1000 Fax +86 21 6119 1264 Evonik Industries AG Rodenbacher Chaussee 4 63457 Hanau Phone +49 0 6181 59 6338 Fax +49 0 6181 59 76338
