Switcher Specifications
Video Inputs/Outputs/Reference
Analog Inputs
Y HDMI Pb Pr HDMI Y Pb
Power Switch. USB Port, and Diagnostics
HDMI Inputs
Pr HDMI
Frame Ports and Pinouts
Network Tally
Y Pb Pr HDMI
Carbonite MultiMedia Frame
Y Pb Pr HDMI Y Pb Pr 1 INPUTS PS 1 2 3 LTC PS 2 TALLY GPIO 4 5 6 7 8 PSL 9 10 2 1 SERIAL OUTPUTS 11 12
Power Switch
13
14
15
16
17
18
19
20
21
22
23
24
SDI Inputs Reference In
Carbonite Frame (Interior front)
POWER
ON OFF
Panel
Y Pb Pr HDMI Y Pb Pr HDMI Y Pb Pr HDMI
(female RJ-45)
Serial
Pin
22 23 24
UPGRADE
FRM UPGD 1 2 3 4 5 6 7 8 PANEL MC POWER PS1 PS2
Status LEDs
1 INPUTS PS 1
12345678
3 LTC PS 2
8 PSL
10 2 1
11
12
13
14
15
16
17
18
19
20
21
TALLY GPIO
PV
PGM
OUT1
OUT2
IN
REF
SERIAL OUTPUTS
PV
PGM
OUT1
OUT2
IN
REF
Linear Timecode Input
Carbonite+/Carbonite Frame
1 INPUTS PS 1 2 3 PS 2 4 5 6 7 8 PSL 9 10 2 1 SERIAL 11
Output BNCs
Reference Out
USB
DIP Switches
Power
GPI I/O
Serial
1 2 3 4 5 6 7 8
RS-422
Tx+ TxRx+ n/c n/c RxGround Ground
12
13
14
15
16
17
18
19
20
21
22
23
24
SDI Inputs Reference In
PS 1 PS 2 FRAME NEXT
(female DB37)
GPI I/O
(female DB37)
Tally
LTC
TALLY GPIO
OUTPUTS
PV
PGM
OUT1
OUT2
IN
REF
Pin
Carbonite 2M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Linear Timecode Input
Output BNCs
Reference Out
Power
Note: If you purchased the 16 input variant of Carbonite (116 or 216),
only the first 16 Input BNCs on the back of the frame can be used.
Note: The Carbonite 10 control panel has a power switch to
power it on, or off. The other Carbonite control panels power on automatically when the power supply is plugged in.
Note: Only one of Analog Input 1, HDMI 1, and SDI Input BNC 6 can be
used at the same time. The same applies to Input BNCs 12, 18, and 24.
Note: MultiViewers can be assigned to any assignable output, or to PV.
GPI I/O 1 GPI I/O 2 GPI I/O 3 GPI I/O 4 GPI I/O 5 GPI I/O 6 GPI I/O 7 GPI I/O 8 GPI I/O 9 GPI I/O 10 GPI I/O 11 GPI I/O 12 GPI I/O 13 GPI I/O 14 GPI I/O 15 GPI I/O 16 GPI I/O 17 GPI I/O 18 GPI I/O 19
Signal
Pin
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
GPI I/O 20 GPI I/O 21 GPI I/O 22 GPI I/O 23 GPI I/O 24 Ground GPI I/O 25 GPI I/O 26 GPI I/O 27 GPI I/O 28 GPI I/O 29 Ground GPI I/O 30 GPI I/O 31 GPI I/O 32 GPI I/O 33 GPI I/O 34 --
Signal
Pin
1 Common (2-6, 20-25) 2 Tally 1 3 Tally 2 4 Tally 3 5 Tally 4 6 Tally 5 7 Tally 6 8 Tally 7 9 Tally 8 10 Tally 9 11 Tally 10 12 Tally 11 13 Tally 12 14 Tally 13 15 Tally 14 16 Tally 15 17 Tally 16 18 Tally 17 19 Common (13-18, 32-37)
Tally
Pin
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Tally 18 Tally 19 Tally 20 Tally 21 Tally 22 Tally 23 Tally 24 Tally 25 Tally 26 Tally 27 Tally 28 Common (7-12, 26-30) Tally 29 Tally 30 Tally 31 Tally 32 Tally 33 Tally 34
Tally
Note: GPI Output pin 37 is not used at this time.
Specifications
HDMI Input Formats VGA 640480 (4:3) SVGA 800600 (4:3) XGA 1024769 (4:3) SXGA 12801024 (5:4) 1080i 19201080 (16:9) 1080p 19201080 (16:9) SDI Input Formats 480i 59.94Hz 576i 50Hz 720p 59.94Hz 720p 50Hz 1080i 59.94Hz 1080i 50Hz 1080pSF 23.98Hz 1080pSF 25 1080pSF 29.97 Default Values Frame IP (LAN1) 192.168.0.123 Frame IP (LAN2) 0.0.0.0 FTP User name user FTP Password password Input Voltages 100 - 120V~ 220 - 240V~ 47-63Hz Panel Power Consumption Carbonite 10 24W 2.0A 12V Carbonite 1-A 30W 2.5A 12V Carbonite 1M 30W 2.5A 12V Carbonite 2 42W 3.5A 12V Carbonite 2M 50W 4.2A 12V Carbonite 2S 54W 4.5A 12V Carbonite 2X 66W 5.5A 12V Frame Power Consumption Carbonite 90W 7.5A 12V Carbonite+ 110W 9.2A 12V Carbonite MM 125W 10.4A 12V Video Input Specifications >100m @ 1.5 Gb/s Equalization (using Belden 1694 cable) >300m @ 270 Mb/s (5-40C) Impedance 75 ohm, terminating SMPTE 259M/292M serial digital Video Inputs, SDI (non-looping) Video Inputs, HDMI HDMI 1.4 High Speed HDMI Cable (Max 10m) Video Inputs, Analog Levels 1V peak-to-peak, nominal Standard Definition analog black Reference Inputs (non-terminating, looping) High Definition tri-level sync Video Output Specifications Return Loss > 17dB @ 1.5GHz Rise and Fall Time 800ps +/- 10% (SD) 240ps +/- 10% (HD) Signal Level 800mV +/- 10% DC Offset 0 Volts Overshoot < 10% HD Mode 10-bit SMPTE-292M serial digital
Panel/Frame
Tally Rating Input Voltage: 24VAC (rms) / 40VDC Maximum Current: 120mA Impedance: < 15 ohms Operating: Storage: Temperature 0 - 40C (32 - 104F) -20 - 85C (-4 - 185F)
Video Production Technology
2013 Ross Video Limited. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited.
Information in this document is subject to change without notice.
4802DR-200-11
Frame Installation and Cabling
Rack Mounting
1
Power and Control Cabling
Connect video input sources as needed
Y
Frame Door Opening
SDI Analog (YPbPr Cable) HDMI (High Speed HDMI Cable)
Pb
Pr HDMI
Pb
Pr HDMI
Pb
Pr HDMI
Pb
Pr HDMI
1
22 23 24
Locked Unlocked
Y Y Pb Pr HDMI 18 19 Pr HDMI 12 13 15 16 17
Pb
Pr
HDMI 24
1 INPUTS PS 1
3 LTC PS 2
20
21
22
23
8 PSL
10 2 1
11
12
13
14
15
16
17
18
19
20
21
TALLY GPIO
Pb
14
Rack Mount Arm
Pb
Pr
HDMI 6 7
8 PSL
10 2 1
11
1 INPUTS PS 1
3 LTC PS 2
5 LY
1 SER IAL OUTPU TS
PV
PGM
OUT1
OUT2
IN
REF
TAL
GPIO
Shielded Twisted Pair Maximum 200m cable length
SERIAL OUTPUTS
PV
PGM
OUT1
OUT2
IN
REF
Connect external reference or use internal reference Connect aux outputs as needed
2
POWER
ON OFF
UPGRADE
FRM UPGD 1 2 3 4 5 6 7 8 PANEL MC POWER PS1 PS2
12345678
Pb
Pr
HDMI 24
Pb
Pr
HDMI 18 19
20
21
22
23
Pb
Pr
HDMI 12 13
14
15
16
17
Pb
Pr
HDMI 6 7
8 PSL
10 2 1
11
1 INPUTS PS 1
3 LTC PS 2
5 LY
1 SER IAL OUTPU TS
PV
PGM
OUT1
OUT2
IN
REF
Connect Program and Preview Out
PS 1 PS 2 FRAME NEXT
TAL
GPIO
Retaining Bolts
Carbonite 2M
Rail Guide
Rack Mount Arm
Note: It is recommended that you always connect the
AC Power Adapter to the Control Panel before connecting to Mains Power.
Frame Dust Filter Remove frame door before cleaning the dust filter.
Frame Dust Filter
Pb
Pr
HDMI 24
Pb
Pr
HDMI 18 19
20
21
22
23
Powering On Switcher
Pb
Pr
HDMI 12 13
14
15
16
17
Pb
Pr
HDMI 6 7
8 PSL
10 2 1
11
1 INPUTS PS 1
3 LTC PS 2
5 LY
1 SER IAL OUTPU TS
PV
PGM
OUT1
OUT2
IN
REF
TAL
GPIO
Power Switch
5/16 Hex Nuts
POWER
ON OFF
Power Switch
POWER
ON OFF
FRM UPGD 1 2 3 4 5 6 7 8 PANEL MC POWER PS1 PS2
UPGRADE
12 V 4A
12345678
PS 1
PS 2
FRAME
EXT LINK
Pb
Pr
HDMI 24
Pb
Pr
HDMI 18 19
20
21
22
23
Carbonite 10
Pb
Pr
HDMI 12 13
14
15
16
17
Pb
Pr
HDMI 6 7
8 PSL
10 2 1
11
1 INPUTS PS 1
3 LTC PS 2
5 LY
1 SER IAL OUTPU TS
PV
PGM
OUT1
OUT2
IN
REF
Note: The Carbonite 10 control panel has a power
TAL
GPIO
Threaded Rubber Bumpers
switch that must be used to power on the control panel. All other Carbonite control panels power on when plugged in.
Note: The Dust Filter located inside the frame door
should be kept clean and free of dust buildup to ensure proper cooling of the frame. Always ensure that the Dust Filter is covering all the holes in the door.
Having a problem? Call our free, 24-hour technical support hotline to speak with a live product specialist located right here in our facility. Tel: (+1) 613 652 4886 Email: [email protected]
Video Production Technology
Printed In Canada
