G115
Cast Iron Residential Oil Boiler
Often Imitated. Never Duplicated.
High Efficiency - AFUE’s Above 86%
Flexible, Corrosion Resistant GL-180M Cast Iron
Full Swing Burner Door for Excellent Serviceability
Chimney and Direct Vent Options
74,000 to 120,000 BTU/Hr Output
Comfortable. Efficient. Intelligent Heating.
www.buderus.net
G115
A better way to heat your home. The modified three-pass boiler:
The Buderus G115 boiler is designed and built to the highest industry standards. It extracts and
delivers more heat from every fuel dollar. Acknowledged as the leader in high-efficiency, low emission The G115 modified three-pass boiler is
hydronic heating, Buderus offers innovative design, quality manufacturing, exceptional efficiency and designed for:
performance.
Optimized combustion with positive
A G115 cast iron oil boiler is ideal for new installations or as a replacement for virtually any make or pressure-fired boilers and tailored
model of boiler. They are compatible with most hot water tanks. Constructed with superior materials chamber geometry — no need for a
and designed by the industry’s leading engineers, the G115 boiler has set the standard for the industry. heat-consuming refractory or target wall
With two ETL approved venting options either into a chimney or directly through the wall, the G115 eliminating the need for costly repairs.
allows a wide range of installation possibilities.
Minimal stack losses with the modified
three-pass flue design’s large heat
transfer areas.
Low standby losses with a full 3" jacket
of thermal insulation around the entire
block — even underneath the boiler!
Comfortable Efficient
Keeping your home comfortable and warm is a Energy star ratings for boilers are based on an
high priority—but it doesn’t have to come at a Annual Fuel Utilization Efficiency (AFUE)
high cost. Whether you heat by baseboard, panel rating, which is a ratio of the heat produced How it works.
radiators, hydro-air systems or radiant flooring, to the energy consumed on an annual basis. The flame fires into the first chamber. Then the
our advanced heating systems will provide many Not only is the Buderus G115 boiler Energy flue products flow through the second pass to
years of exceptional comfort and economy. Star rated, but it is also designed for ease of the front of the boiler. From there they reverse
Unlike a conventional boiler which heats installation and maintenance. With features like direction again —moving through the third
and circulates water at only one temperature a compact dimension and integrated handles for
pass to the back, and finally exiting via the flue
— typically 170° to 180° F and keeps heating ease of transporting, adjustable leveling legs, rear
and circulating this high temperature water until tappings and flue connection, baffles and clips connection into the chimney. Because the
the thermostat signals it to stop. A Buderus for adjusting stack temperatures and a heavy gases are held in the boiler longer this allows
boiler, especially when paired with the Logamatic gauge blue enameled jacket, a Buderus boiler is the cast iron to absorb the maximum amount of
control, eliminates these room temperature not only efficient, but it is easy to install. heat, resulting in a lower stack temperature and
swings by adjusting the boiler water temperature a higher efficiency.
to the current conditions, saving fuel while With a full “swing” burner door, which can
keeping you warm and comfortable. be hinged on either the left or the right, and
front access plugs which permit flushing of the
boiler’s interior, the G115 can be thoroughly and
properly cleaned in a fraction of the time it takes
to clean a conventional boiler.
1-800-283-3787
Intelligent Heating – By Design
The G115 is designed in Europe where fuel costs are significantly higher and environmental
regulations are more stringent. Using state of the art techniques in the design and Manufactured with the patented Buderus
manufacturing process, the G115 is built to maximize the heating value of every ounce of GL-180M flexible cast iron, the sections
fuel and constructed with the highest quality materials. are tightly joined together and sealed
by profiled, beveled steel push nipples,
Manufactured without a heat-consuming refractory or target wall, service and maintenance
ensuring a long life with no leakage.
calls are minimized, while fuel efficiency and heat transfer is maximized. The patented
Buderus GL-180M flexible cast iron ensures that the boiler resists thermal shock under
conditions of rapid temperature change. Sections are securely joined together and sealed by
profiled, beveled steel push nipples, ensuring a long life with no leakage. Special compounds
provide a gas-tight seal for safe and efficient operation. The full 3" thermal insulation around
the boiler, including underneath, increases efficiency by almost eliminating standby and stack
temperature losses.
Buderus, the world leader in heating technology, manufactures the highest quality boilers
based on centuries of experience. With its innovative design and quality manufacturing, a
Buderus boiler will outlast and out-perform virtually any other residential hot-water system in
the world.
Domestic Hot Water Tanks Convenient Logamatic Control
Need domestic hot
water? Then combine
your Buderus boiler
with a Buderus indirect
hot water tank. A
Adding a Buderus Logamatic control will Special compounds provide a gas-tight seal for
Buderus tank is so well
give you the ultimate in comfort and fuel
insulated that it loses safe and efficient operation. And, thanks to the
less than ¼º per hour. savings. Microprocessor-based controls allow
GL-180M cast iron’s amazing flexibility, this
Available in a vertical, the Logamatic to intelligently manage both
your home heating and domestic hot water. boiler resists thermal shock under conditions of
or a horizontal space
saving model that The Logamatic has 16 standard functions rapid temperature change.
installs under the boiler, these tanks have including day/night setback, automatic
a higher recovery rate than stand alone or summer/winter changeover and even a
tankless coil models. While a Buderus boiler vacation mode. Set it once and relax in the
works great with any hot water tank – you
comfort of your warm home.
can be sure of increased boiler efficiency,
system longevity and minimized service
calls when you insist on a Buderus tank and
boiler.
Complete your system for added comfort
to your home!
Once you have a Buderus boiler you can add a Buderus indirect fired hot water tank, an
optional Buderus Logamatic control or both. The Logamatic control maximizes your comfort
and fuel savings, it will also accommodate specialized heating applications such as radiant
flooring. Combined, this premium heating system will provide years of exceptional comfort
and economy . . . for little more than cost of a standard replacement components.
The G115 shown with horizontal tank and Logamatic control.
G115 and LT tanks can be used in any combination except
for the G115/34 and the LT160.
www.buderus.net
G115
Cast Iron Residential Oil Boiler
"
"
" " "
"
"
" "
"
" "
"
"
Model G115/21 G115/28 G115/34 All G115
KP Kits Include:
Performance Data
Gross Output MBH
ı L7248C1006
74 98 120
aquastat
# of Sections 3 4 5
Net IBR MBH 64 85 104 ı Flexible oil line
Firing Rate (GBH) .60-.75† .80 1.0 ı Circulator
AFUE 86.5 % 86.8% 86% ı Flanges
Piping Connections
Vent Connection Size 5˝ 5˝ 5˝
Supply 1¼˝ 1¼˝ 1¼˝
Return 1˝ 1˝ 1˝
Physical Dimensions
Overall Boiler Length (L) 26¼˝ 31˝ 35¾˝
Boiler Block Length (LK) 21¼˝ 25¾˝ 30½˝
Minimum Boiler Width 18˝ 18˝ 18˝
Boiler Width 23½˝ 23½˝ 23½˝
Minimum Boiler Height 33½˝ 33½˝ 33½˝
Height 34½˝ 34½˝ 34½˝
Boiler Feet Spacing 13¼˝ 18˝ 22½˝
Fire Box Depth (T) 16˝ 20½˝ 25˝
Fire Box Volume cu. ft. 1.20 1.75 2.21
Dry Weight (lbs) 330 403 476
Water Content (gal) 8.7 10.8 12.9
Recommended Clearances for Ease of Serviceability
Side 15˝ 15˝ 15˝ MEA# 358-91-E
Rear 20˝ 20˝ 20˝
CRN# 1495.9c, 620.T
† NOTE: G115/21 Dual Firing Rate capability - from .60-.75 - is only available with Carlin EZ1 burner or Riello F3 burner. The higher the Firing Rate will result in a D.O.E. heating capacity of
90,000 BTU/Hr. and the Net IBR Rating of 77,000 BTU/Hr.
Clearance Requirements
Front Side Rear Top Galvanized Flex AT-4 FT-4 G115 direct vent installation tips
Vent Insulated Exhaust Only Concentric
Pipe Oil Vent Termination Termination
ETL approved with two 4" 90° elbows, and up to 6' of 4" regular smoke pipe for short vent
24˝ 6˝ 18˝ 6˝ 18˝ 1˝ 1˝ 1˝ runs. For longer runs, use up to 10' of flexible stainless steel insulated oil vent.
Use 4" metal pipe for air intake. Use at least 6' to 8' of 4" metal pipe for air intake in
9"
3"
conditioned space in cold climates (below –20ºF)
7 4
6 4 Direct vent burners are equipped with pre-and post-purge cycles for safe, complete exhaust
4 5"
of all combustion products, while cooling oil burner nozzle for positive shut-off.
13"
26" 18" Buderus recommends the use of Becket, Carlin and Riello. Please refer to the Buderus trade
price list for models.
AT-4 Aerocowl Termination FT-4 Concentric Pipe-in-Pipe Termination
One of the two ETL certified terminations are required for use with G115 series boilers for direct vent
applications. Both terminations are “zero clearance” systems for easy and versatile applications.
BBT North America Corporation
50 Wentworth Avenue
Londonderry, NH 03053 Subject to change without notice
Tel: (603) 552-1100 © 2006 Buderus
Fax: (603) 584-1681 Part Number 44499015-04/07
