Scribd
Upload
474 views4 pages

Ručni Unos Linije I Unos Preko USB Za Amiko HD

1. Connect the Ethernet cable to the receiver and check that the IP address is obtained correctly. If not, manually set the IP address. 2. Go to the menu to configure up to 8 servers. Edit the server settings including name, port, username, password, and DES key. Select the server as active. 3. Create a text file on USB with server settings in a specified format and read it into the receiver to auto-configure multiple servers.

Uploaded by

emir_inter1
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
474 views4 pages

Ručni Unos Linije I Unos Preko USB Za Amiko HD

1. Connect the Ethernet cable to the receiver and check that the IP address is obtained correctly. If not, manually set the IP address. 2. Go to the menu to configure up to 8 servers. Edit the server settings including name, port, username, password, and DES key. Select the server as active. 3. Create a text file on USB with server settings in a specified format and read it into the receiver to auto-configure multiple servers.

Uploaded by

emir_inter1
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

Connect to Ethernet
Connect Ethernet cable to receiver. Enter Menu/Internet/network Local Setting, see did receiver obtained IP address correctly, if it is ok, you will see your IP address in this window after couple seconds. If not, switch DHCP to OFF and set IP manually.

2. Connecting to the server


Go to MENU/Internet/Net client config You can choose server here, there can be maximum 8 servers. Press YELLOW button to EDIT server.

Edit each field replacing the text with your server settings. If server which you connect to is NEWCAMD, you should get from your donor: 1. Server name (or IP of the server) 2. Service port 3. User name 4. Password 5. DES key

6. Press ACTIVE SERVER (dot from left side will change color from white to green) 7. Press STORE to save settings

If you have access to CCCAMD server, you have to input: 1. Server name (or IP of the server) 2. Service port 3. User name 4. Password 5. Press ACTIVE SERVER (dot from left side will change color from white to green) 6. Make sure you changed protocol to CCCAMD 7. Press STORE to save settings

After Exit receiver will automatically try to connect to the server, if all ok, will color of the server will change to green:

3. Read-in server from text file.


Available from sw version 1.1.34 or newer. Put file directly on USB, without any folder. File with server can be read-in only from menu net client config by FIND button on remote( see above) Content of the file:
# # # # # # # # # # hsdata.cfg - config file for X403p X402p working from software 1.1.29 need copy this file to C: of ur usb stick. then put receiver to read cmd -> cfg~lock~hide~pass sample cfg~1~1~00110022 means , u will lock the server info menu. also hide the server info. the password to watch is 00110022 cmd -> protocol~host~port~user~pass~des sample newcamd~192.168.2.3~10000~dummy~dummy~0102030405060708091011121314 sample homecamd~192.168.2.3~10000 sample homecamd2~192.168.2.3~10000 sample cccamd~192.168.2.3~10000~dummy~dummy sample nasscamd~192.168.2.3~10000

#newcamd~192.168.2.3~11000~dummy~dummy~0102030405060708091011121314 #newcamd~192.168.2.3~12000~dummy~dummy~0102030405060708091011121314 #homecamd~192.168.2.3~13000 #homecamd2~192.168.2.3~14000 #cccamd~192.168.2.3~15000~dummy~dummy #nasscamd~192.168.2.3~16000 #nasscamd~192.168.2.3~17000

So first we edit file on PC and input our server settings, For newcamd it will look like:: newcamd~server~port~username~password~DESkey for cccamd: cccamd~server~port~username~password without any space and # sign (text with # on front is skipped) read-in the file from Net client config menu by FIND button:

1. Press FIND on remote 2. Press YES on the screen to confirm 3. Wait until receiver will reboot

You might also like