Speed Dome Camera Controller Operation Manual

Please read this operation manual before using this device and use the device properly. Also, please keep this manual with care to ensure easy access at any time.

SAFETY PRECAUTIONS

CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN!

CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO DOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lighting flash with a arrowhead symbol, in an equilateral triangle, is intended to alert the user. There is uninsulated dangerous voltage presence near by the product's enclosure which may be risk of to persons .

The exclamation point within an equilateral triangle is intended to alert the user to reference of the important operating and maintenance (servicing ) instructions .

THE PRODUCT CODE MARKED ON THE BOTTOM COVER. PLEASE FILL THE CODE IN THE FOLLOWING BLANK. PLEASE SAVING THIS SPECIFICATION CAREFULLY, SO THAT CHECKING MODEL:________________________________________ PRODUCT CODE:______________________________________
.

INDEX
I. Summary3

II. Introduction of Function...3 III. Introduction of the Keyboards Panel..3 IV. Setting of the Keyboard.4 V. Operation of the Keyboard5 VI. Installation and Connection7 VII. Technical Specifications..8 VIII. Points for Attention.....8

I. Summary
The keyboard controller is used for terminal receivers such as the intelligent Speed Dome and the decoder etc. Taking the EIA/RS-485 electrical interface between the keyboard and the receiver, one keyboard can control as much as 32 speed dome and decoders without driving the bus and the maximum communication distance between the keyboard and the receiver is up to 1.2 km. Its very easy for operating and setting the Speed Dome Camera. The controller is also to control the terminal receiver to achieve the function of controlling pan/tilt, lens and etc.

Main Functions:

Set the address range of the dome camera and the decoder064. Control all functions of the dome camera such as Power ON/OFF. To operate the pan/tilt of Speed Dome Camera moving in different speed lever Set or call the points of the dome camera. Altogether 64 preset points can be set. Manually or automatically control the dome camera, and change the settings of particular camera by call the menu of the camera. Manually control the focus, zoom and iris of the camera.

II. Introduction of Functions

Control the focus, zoom and iris of the camera.

Operation of Preset Position 1~64 Set Preset Position Call Preset Position Operation of Cruise Track 1~6 Run Cruise Track Automatic Horizontal Scan Control of dome Self-Learning Track of Intelligent Speed Dome Function Setting of Menu of Speed Dome Direct Control on Decoder Control front devices such as the decoder etc. (including speed and direction of scan)

III.

Introduction of the keyboard Panel

There are speed joystick, buttons and nixie light on the front panel of the control keyboard. The display is used to show the address of the speed dome as well as the number inputted. The joystick controls the upward, downward, leftward and right ward speed motion of the speed dome. The description of buttons is as follows:

MENU

Figure 1

CAMSelect address of the intelligent Speed Dome . MENUAuxiliary control buttons. AUTOTo control auto-horizontal rotation for pan/tilt. CLEAR To clear inputted data 0-9 Number key WIDETo a wide angle. TELETo turn to a telescopic range. FARTo make focus far manually. NEARTo make focus near manually. OPENTo open iris. CLOSETo close iris. ONSwitch on the setting of function. OFFSwitch off the setting of function. CALLTo call the preset position. PRESETTo set the preset position. SHOTTo call cruising track.

2. Rear Panel (Figure 2)

DC12V OUT GND RS485 + + -

A. Power input connector: input DC12V power. B. DC12V Output. C. Communication connector RS485: D. ID-Code switch: Used to set the protocol in use and the baud rate of communications.

IV.

Setting of the Keyboard

ID-Code in Figure 2. DIP1-DIP4 are used to select type of the communication protocol as per following table
State of ID-CODE Type of Protocol A01 NEON B01 SAMSUNG Santachi PELCO-D PELCO-P/4800Bps PELCO-P/9600Bps HUNDA600 Setting of Protocol Type DIP1 OFF ON ON ON OFF ON OFF ON DIP2 OFF OFF OFF OFF ON ON OFF ON DIP3 OFF OFF OFF OFF OFF OFF ON ON DIP4 OFF OFF OFF OFF OFF OFF OFF OFF Setting of default Baud Rate DIP5 ON OFF OFF OFF OFF OFF ON OFF OFF DIP6 OFF ON ON ON ON OFF OFF ON ON

b) DIP5 and DIP6 are used to select the baud rate, shown as following table(DIP7 and DIP8 are not used)
Status of ID-Code Baud Rate

DIP1

DIP2

DIP3

DIP4

DIP5 OFF ON OFF ON

DIP6 OFF OFF ON ON

DIP7

DIP8

2400bps 4800bps 9600bps 19200bps c) Some of the ID-Code of the protocols are set as follows:

B01/9600Bps

ON 1 2 3 4 5 6 7 8

NEON /9600Bps

ON 1 2 3 4 5 6 7 8

PELCO-D/2400Bps

ON 1 2 3 4 5 6 7 8

PELCO-P/4800Bps

ON 1 2 3 4 5 6 7 8

PELCO-P/9600Bps

ON 1 2 3 4 5 6 7 8

HUNDA600/9600Bps

ON 1 2 3 4 5 6 7 8

V.

Operation of the Keyboard

Select Address of Speed Dome Camera /Decoder[N]+[ CAM] DescriptionN No. of camera from 0 to 64 FunctionSelect the address of the camera to be controlled. When the value N is in conformity with the address of the speed dome, it will be under control. 2. To set preset position[N]+[ PRESET] DescriptionN No. of preset position from 1 to 64. FunctionStore current position and refer it as No. N position. 3. Call the Preset position[N]+[ CALL] Description:N No. of preset position from 1 to 64. Function Transfer the camera to the position of No. N preset position. 4. Cancel the Preset position: [N]+[CLEAR] DescriptionN No. of preset position from 1 to 64. FunctionDelete the No. N Preset position stored. 5. Tour the Track[N]+ [SHOT] DescriptionN No. of the track from 1 to 6. FunctionTour the No. N track and stop tour by pushing the joystick. 6. To turn on Auto Pan (Operation of NEONSAMSUNG Protocol)[AUTO]+[P1]+[ON]+[P2]+[OFF] DescriptionP1 the starting scan No. of preset point from 1 to 64, which should be set already. DescriptionP2 the ending scan No. of preset point from 1 to 64, which should be set already. If P1 = P2 or P1 and P2 are coincided, the speed dome will make scan in range of 360. Note: For PELCO-DPELCO-P Protocol the way of operation is as follows: Set the starting scan position: Transfer the Speed Dome to the starting scan position, operation [AUTO]+[ON] Set the ending scan position: Transfer the Speed Dome to the ending scan position,operation [AUTO]+[OFF] Run Auto Pan[AUTO]+[SHOT] Auto Pan operation takes the following parameters. You must set these parameters before using a 1. Auto Pan command to begin the scan operation. You can use the scan stop command ot PT scan stop command to stop the scan. Setting scan condition. Auto Pan Position(First specify position, second specify position) Auto Pan Speed and Direction 7. Stop Auto Pan[AUTO]+[OFF]( Only A01B01 Available) or push the joystick to stop scan 8. Control the zoom of the Camera[WIDE]/[TELE] 9. Control the Focus of the Camera[FAR]/[NEAR] 10. Control the Iris of the Camera[OPEN]/[CLOSE] 11. Auxiliary Control of the CameraBy combination of [MENU] and [ON], [OFF] buttons, you can set some data of the camera, and functions are listed as follows(operations of NEON Protocol) No. of Value N 0 1 2 Camera control Control Object power supply/reset Definition of Keyboard Operation [MENU]+N+[ON] Power ON/OFF Switching ON ON
6

[MENU]+N+[OFF] Recover Initial Values of Camera OFF OFF

Back Light Compensation Zero Illumination (refer to function of camera)

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Menu/Display (refer to function of camera) Digital Zoom Reserved Focus Iris White Balance ModeWB Black & White/Color Switching Set Auto Pan (Only conditions for scan. If start scan, operate as Item 6 in this paragraph) Reserved Reserved Self-learning programming of track

ON ON Automatic Automatic Automatic Indoor Mode ATW Mode Color < 180, low speed < 180, middle speed < 180, high speed

OFF OFF Manual Manual Manual Outdoor Mode One Push WB Black & White > 180, low speed > 180, middle speed > 180, high speed

Start Programming Run

End Programming Move joystick to stop

Control of self-learning of track

For different camera, control functions in the list could be different. For the camera with the menu, switch ON/OFF the menu by [MENU]+[3]+[ON], and switch ON/OFF the OSD by [MENU]+[3]+[OFF]. In case the camera has the menu and the menu is ON 1. Select the item on the menu by buttons [WIDE]/[TELE] to scroll the cursor up or down; 2. Chang the status of the selected item on the menu by buttons [FAR]/[NEAR]; 3. Switch OFF the menu as per operations in the list after the menu is set. Take care of differences between the Menu of Speed Dome and the Menu of Camera. For the speed dome with the menu, enter the menu by [64] +[CALL] and basic operations are as follows 1. Call No.64 preset point to open the main menu by the control keyboard. 2. When the menu appears on the screen, move the cursor to the item you need to set by TILT UP and TILT DOWN, and enter the settings of the item to make change by PAN LEFT and PAN RIGHT; 3. Speed up operation of the joystick after keeping it for one second in one direction. 4. All settings of the menu could not be lost even power failure occurred; 5. Operations under special case can be referred on the description of the menu of the ball machine. 12. Use the Joystick to Control the Speed Dome Camera Figure3 You can use the speed joystick to control the Pan/Tilt direction and speed of the dome of the camera randomly. The speed of pan/tilt is decided by the angle of the joystick you operated (Figure 3). Change the tilting angle of the joystick you can adjust the speed evenly and the camera can be focused automatically in the course of scan to keep images being distinct.

VI. Installation and Connection

connecting wires. Any incorrect connections can cause permanent damage of the device. When connecting wires, first switch off the power supply of all devices. The communication wires between devices should be shielded twisted cable. When installing cables they should be far away from high voltage lines or other possible interference circuits as can as possible. 1. Connections of the keyboard controller controlling multiple speed dome cameras(figure4) 2.Connections between the keyboard and the speed dome camera(Figure5)

T+ T-

1 2 3 4 5 6 7 8

A LM A LM DC I N GND R+ RVI DEO VI DEO +

D O M E SPEED 1 A LM 1 A LM 2 3 DC I N GND 4 R+ 5 R6 VI DEO 7 VI DEO + 8 DO M E SPEED N

MENU

Figure5

Figure4

VII.

Technical Specifications
Communication between Speed Dome Camera and ControllerPort to multi-port and half duplex function. Communication connector: RS-485. Baud Rate of CommunicationFour baud rates i.e. 2400Bps, 4800Bps, 9600Bps and 19200Bps. Distance of Communication1200 M in maximum Power Supply500 mAthe input voltage of power supply is variable for power supplys specification Size 188 97 70mm Weight0.5 Kg Number of Controlled Speed Dome Camera up to 32.

VIII. Points for Attention

Please read the operation manual of the keyboard carefully before using it. The operation manual is mainly focused on all functions of B01 Protocol. For other different
8

protocols, operations could be something difference and those different parts will be listed on Supplementary Description of the Keyboard Controller in details. The keyboard takes 12V DC power supply. Please confirm the voltage and polarity before the power supply is switched on. Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock. As the keyboard is a sophisticated electronic device, you should never open the case so as to avoid the occurrence of trouble. The keyboard has integrated multiple protocols, and you are pleased to select correct protocol and the baud rate.