e le ct rical-e ngine e ring-po rt al.co m http://electrical-engineering-po rtal.

co m/flo ating-neutral-impacts-in-po wer-distributio n

Floating Neutral Impacts in Power Distribution

jiguparmar

Flo ating Ne utral Imp ac ts in Po we r Dis trib utio n (p ho to b y Mard ix Limite d ; Fic kr)

Introduction
If the Neutral Conductor is opened, broke or lost at either of its source side (Distribution Transformer, Generator or at Load side Distribution Panel of Consumer), the distribution systems neutral conductor will float or lose its ref erence ground Point. T he f loating neutral condition can cause voltages to f loat to a maximum of its Phase volts RMS relative to ground, subjecting to its unbalancing load Condition. Floating Neutral conditions in the power network have dif f erent impact depending on the type of Supply, type of installation and Load balancing in the Distribution. Broken Neutral or Loose Neutral would damage to the connected load or create hazardous Touch Voltage at equipment body. Here We are trying to understand the Floating Neutral Condition in T-T distribution System.

What is Floating Neutral?

If the Star Point of Unbalanced Load is not joined to the Star Point of its Power Source (Distribution Transf ormer or Generator) then Phase voltage do not remain same across each phase but its vary according to the Unbalanced of the load.

As the Potential of such an isolated Star Point or Neutral Point is always changing and not f ixed so its called Floating Neutral.

Normal Power Condition and Floating Neutral Condition

Normal Power Condit ion:
On 3-phase systems there is a tendency f or the star-point and Phases to want to balance out based on the ratio of leakage on each Phase to Earth. T he star-point will remain close to 0V depending on the distribution of the load and subsequent leakage (higher load on a phase usually means higher leakage). T hree phase systems may or may not have a neutral wire. A neutral wire allows the three phase system to use a higher voltage while still supporting lower voltage single phase appliances. In high voltage distribution situations it is common not to have a neutral wire as the loads can simply be connected between phases (phase-phase connection).

3 Phase 3 Wire Syst em:

T hree phases has properties that make it very desirable in electric power systems. Firstly the He althy p o we r s ys te m s c he me phase currents tend to cancel one another (summing to zero in the case of a linear balanced load). T his makes it possible to eliminate the neutral conductor on some lines. Secondly power transf er into a linear balanced load is constant.

3 Phase 4 Wire Syst em f or Mix Load:

Most domestic loads are single phase. Generally three phase power either does not enter domestic houses or it is split out at the main distribution board. Kirchhof f s Current Law states that the signed sum of the currents entering a node is zero . If the neutral point is the node, then, in a balanced system, one phase matches the other two phases, resulting in no current through neutral. Any imbalance of Load will result in a current f low on neutral, so that the sum of zero is maintained. For instance, in a balanced system, current entering the neutral node f rom one Phase side is considered positive, and the current entering (actually leaving) the neutral node f rom the other side is considered

negative. T his gets more complicated in three phase power, because now we have to consider phase angle, but the concept is exactly the same. If we are connected in Star connection with a neutral, then the neutral conductor will have zero current on it only if the three phases have the same current on each. If we do vector analysis on this, adding up sin(x), sin(x+120), and sin(x+240), we get zero . T he same thing happens when we are delta connected, without a neutral, but then the imbalance occurs out in the distribution system, beyond the service transf ormers, because the distribution system is generally a Star Connected. T he neutral should never be connected to a ground except at the point at the service where the neutral is initially grounded (At Distribution Transformer). T his can set up the ground as a path f or current to travel back to the service. Any break in the ground path would then expose a voltage potential. Grounding the neutral in a 3 phase system helps stabilize phase voltages. A non-grounded neutral is sometimes ref erred to as a floating neutral and has a f ew limited applications.

Float ing Neut ral Condit ion:

Power f lows in and out of customers premises f rom the distribution network, entering via the Phase and leaving via the neutral. If there is a break in the neutral return path electricity may then travel by a dif f erent path. Power f low entering in one Phase returns through remaining two phases. Neutral Point is not at ground Level but it Float up to Line Voltage. T his situation can be very dangerous and customers may suf f er serious electric shocks if they touch something where electricity is present. Broken neutrals can be dif f icult to detect and in some instances may not be easily identif ied.

Flo ating ne utral c o nd itio n

Sometimes broken neutrals can be indicated by f lickering lights or tingling taps. If you have f lickering lights or tingly taps in your home, you may be at risk of serious injury or even death.

Voltage Measurement between Neutral to Ground

A rule-of-thumb used by many in the industry is that Neutral to ground voltage of 2V or less at the receptacle is okay, while a f ew volts or more indicates overloading; 5V is seen as the upper limit.

Low Reading
If Neutral to ground voltage is low at the receptacle than system is healthy, If It is high, then you still have to determine if the problem is mainly at the branch circuit level, or mainly at the panel level. Neutral to ground voltage exists because of the IR drop of the current traveling through the neutral back to the Neutral to ground bond. If the system is correctly wired, there should be no Neutral to Ground bond except at the source transf ormer (at what the NEC calls the source of the Separately Derived System, or SDS, which is usually a transf ormer). Under this situation, the ground conductor should have virtually no current and theref ore no IR drop on it. In ef f ect, the ground wire is available as a long test lead back to the Neutral to ground bond.

High Reading:
A high reading could indicate a shared branch neutral, i.e., a neutral shared between more than one branch circuits. T his shared neutral simply increases the opportunities f or overloading as well as f or one circuit to af f ect another.

Zero Reading:
A certain amount of Neutral to ground voltage is normal in a loaded circuit. If the reading is stable at close to 0V. T here is a suspect an illegal Neutral to ground bond in the receptacle (of ten due to lose strands of the neutral touching some ground point) or at the subpanel. Any Neutral to ground bonds other than those at the transf ormer source (and/or main panel) should be removed to prevent return currents f lowing through the ground conductors. Top

Various Factors which cause Neutral Floating

T here are several f actors which are identif ying as the cause of neutral f loating. T he impact of Floating Neutral is depend on the position where Neutral is broken:

1) At The Three Phase Dist ribut ion Transf ormer

Neutral f ailure at transf ormer is mostly f ailure of Neutral bushing. T he use of Line Tap on transf ormer bushing is identif ied as the main cause of Neutral conductor f ailure at transf ormer bushing. T he Nut on Line Tap gets loose with time due to vibration and temperature dif f erence resulting in hot connection. T he conductor start melting and resulting broke of f Neutral. Poor workmanship of Installation and technical staf f also one of the reasons of Neutral Failure. A broken Neutral on T hree phases Transf ormer will cause the voltage f loat up to line voltage depending

upon the load balancing of the system. T his type of Neutral Floating may damage the customer equipment connected to the Supply. Under normal condition current f low f rom Phase to Load to Load to back to the source (Distribution Transf ormer). When Neutral is broken current f rom Red Phase will go back to Blue or Yellow phase resulting Line to Line voltage between Loads. Some customer will experience Overvoltage while some will experience Low voltage.

2) Broken Overhead Neut ral conduct or in LV Line

T he impact of broken overhead neutral conductor at LV overhead distribution will be similar to the broken at transformer. Supply voltage f loating up to Line voltage instead of phase voltage. T his type of f ault condition may damage customer equipment connected to the supply.

3) Broken of Service Neut ral Conduct or

A broken Neutral of service conductor will only result of loss of supply at the customer point. No any damages to customer equipments.

4) High Eart hing Resist ance of Neut ral at Dist ribut ion Transf ormer:
Good Earthing Resistance of Earth Pit of Neutral provide low resistance path for neutral current to drain in earth. High Earthing Resistance may provide high resistance Path f or grounding of Neutral at Distribution Transf ormer. Limit earth resistance suf f iciently low to permit adequate f ault current f or the operation of protective devices in time and to reduce neutral shif ting.

5) Over Loading and Load Unbalancing

Distribution Network Overloading combined with poor load distribution is one of the most reason of Neutral f ailure. Neutral should be properly designed so that minimum current will be f low in to neutral conductor. T heoretically the current f low in the Neutral is supposed to be zero because of cancellation due to 120 degree phase displacement of phase current. IN= IR<0 + IY<120 + IB<-120 In Overloaded Unbalancing Network lot of current will f low in Neutral which break Neutral at its weakest point.

6) Shared neut rals

Some buildings are wired so that two or three phases share a single neutral. T he original idea was to duplicate on the branch circuit level the f our wire (three phases and a neutral) wiring of panel boards. T heoretically, only the unbalanced current will return on the neutral. T his allows one neutral to do the work f or three phases. T his wiring shortcut quickly became a dead-end with the growth of single-phase non-

linear loads. T he problem is that zero sequence current From nonlinear loads, primarily third harmonic, will add up arithmetically and return on the neutral. In addition to being a potential saf ety problem because of overheating of an undersized neutral, the extra neutral current creates a higher Neutral to ground voltage. T his Neutral to ground voltage subtracts f rom the Line to Neutral voltage available to the load. If youre starting to f eel that shared neutrals are one of the worst ideas that ever got translated to copper.

7) Poor workmanship and Maint enance

Normally LV network are mostly not given attention by the Maintenance Staf f . Loose or inadequate tightening of Neutral conductor will ef f ect on continuity of Neutral which may cause f loating of Neutral. Top

How to detect Floating Neutral Condition in Panel?

Let us take one example to understand Neutral Floating Condition .We have a Transf ormer which Secondary is star connected, Phase to neutral = 240V and Phase to phase = 440V.

Condit ion (1) Neut ral is not Float ing

Whether the Neutral is grounded the voltages remain the same 240V between phase & Neutral and 440V between phases. T he Neutral is not Floating.

Condit ion (2) Neut ral is Float ing

All Appliances are connected: If the Neutral wire f or a circuit becomes disconnected f rom the households main power supply panel while the Phase wire f or the circuit still remains connected to the panel and the circuit has appliances plugged into the socket outlets. In that situation, if you put a voltage Tester with a neon lamp onto the Neutral wire it will glow just as if it was Live, because it is being f ed with a very small current coming f rom the Phase supply via the plugged-in appliance(s) to the Neutral wire. All Appliances are Disconnected: If you unplug all appliances, lights and whatever else may be connected to the circuit, the Neutral will no longer seem to be Live because there is no longer any path f rom it to the Phase supply. Phase to Phase Voltage: T he meter indicates 440V AC. (No any Ef f ect on 3 Phase Load) Phase to Neutral Voltage: T he meter indicates 110V AC to 330V AC. Neutral to Ground Voltage: T he meter indicates 110V. Phase to Ground Voltage: T he meter indicates 120V. T his is because the neutral is f loats above ground potential (110V + 120V = 230VAC). As a result the output is isolated f rom system ground and the f ull output of 230V is ref erenced between line and neutral with no ground connection. If suddenly disconnect the Neutral f rom the transf ormer Neutral but kept the loading circuits as they are, T hen Load side Neutral becomes Floating since the equipment that are connected between Phase to Neutral will become between Phase to Phase ( R to Y,Y to B), and since they are not of the same ratings,

the artif icial resulting neutral will be f loating, such that the voltages present at the dif f erent equipments will no longer be 240V but somewhere between 0 (not exactly) and the 440 V (also not exactly). Meaning that on one line Phase to Phase, some will have less than 240V and some will have higher up to near 415. All depends on the impedance of each connected item. In an unbalance system, if the neutral is disconnected f rom the source, the neutral becomes f loating neutral and it is shif ted to a position so that it is closer to the phase with higher loads and away f rom the phase with smaller load. Let us assume an unbalance 3 phase system has 3 KW load in R-phase, 2 KW load in Y-phase and 1 KW load in B-phase. If the neutral of this system is disconnected f rom the main, the f loating neutral will be closer to R-phase and away f rom B-phase. So, the loads with B-phase will experience more voltage than usual, while the loads in R-phase will experience less voltage. Loads in Y-phase will experience almost same voltage. T he neutral disconnect f or an unbalanced system is dangerous to the loads. Because of the higher or lower voltages, the equipment is most likely to be damaged. Here we observe that Neutral Floating condition does not impact on 3 Phase Load but It impacts only 1 Phase Load only Top

How to Eliminate Neutral Floating?

T here are Some Point needs to be consider to prevent of Neutral Floating.

a) Use 4 Pole Breaker / ELCB / RCBO in Dist ribut ion Panel

A f loating neutral can be a serious problem. Suppose we have a breaker panel with 3 Pole Breaker f or T hree Phase and Bus bar f or Neutral f or 3 Phase inputs and a neutral (Here we have not used 4 Pole Breaker). T he voltage between each Phase is 440 and the voltage between each Phase and the neutral is 230. We have single breakers f eeding loads that require 230Volts. T hese 230Volt loads have one line f ed by the breaker and a neutral. Now suppose the Neutral gets loose or oxidized or somehow disconnected in the panel or maybe even out where the power comes f rom. T he 440Volt loads will be unaf f ected however the 230V loads can be in serious trouble. With this Floating neutral condition you will discover that one of the two lines will go f rom 230Volts up to 340 or 350 and the other line will go down to 110 or 120 volts. Half of your 230Volt equipment will go up in high due to overvoltage and the other half will not f unction due to a low voltage condition. So, be caref ul with f loating neutrals. Simply use ELCB, RCBO or 4 Pole Circuit Breaker as income in the 3ph supply system since if neutral opens it will trip the complete supply without damaging to the system.

b) Using Volt age St abilizer

Whenever neutral f ails in three phase system, the connected loads will get connected between phases owing to f loating neutral. Hence depending on load resistance across these phases, the voltage keeps varying between 230V to 400V. A suitable servo stabilizer with wide input voltage range with high and low cutof f may help in protecting the equipments.

c) Good workmanship and Maint enance

Give higher Priority on Maintenance of LV network . Tight or apply adequate Torque f or tightening of Neutral conductor in LV system

Conclusion
A Floating Neutral ( Disconnected Neutral) f ault condition is VERY UNSAFE because If appliance is not working and someone who does not know about the Neutral Floating could easily touch the Neutral wire to f ind out why appliances does not work when they are plugged into a circuit and get a bad shock. Single phase Appliances are design to work its normal Phase Voltage when they get Line Voltage Appliances may Damage. Disconnected Neutral f ault is a very unsaf e condition and should be corrected at the earliest possible by troubleshooting of the exact wires to check and then connect properly. Published at Electrical Notes & Articles