Scribd
Upload
409 views2 pages

Hlss Separator For Process Streams

The HLSS separator uses centrifugal force to remove water, sediment, and other contaminants from process streams like fuel or hydrocarbons. It can remove over 99% of water and particles as a bypass filter, reducing maintenance needs for downstream filters and equipment. The separator spins the liquid so that particles and water droplets are removed by a slip stream and returned to the process, while the cleaned stream exits the top of the separator. Different models are available to handle flow rates from 0-24 liters per minute and work with pressures up to 40 barg.

Uploaded by

Didit Andiatmoko
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
409 views2 pages

Hlss Separator For Process Streams

The HLSS separator uses centrifugal force to remove water, sediment, and other contaminants from process streams like fuel or hydrocarbons. It can remove over 99% of water and particles as a bypass filter, reducing maintenance needs for downstream filters and equipment. The separator spins the liquid so that particles and water droplets are removed by a slip stream and returned to the process, while the cleaned stream exits the top of the separator. Different models are available to handle flow rates from 0-24 liters per minute and work with pressures up to 40 barg.

Uploaded by

Didit Andiatmoko
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HLSS separator for process streams

The Hobr Instruments HLSS separator provides a maintenance free solution for highly
diverse applications for removal of water, sediment and many other contaminants from
process streams like fuel or other hydrocarbons. HLSS Separator will do >99 % of the water
removal, including most of the particles, as bypass filter. This results in considerable lower
maintenance of secondary filters and equipment.


The separator works by using centrifugal force to separate the particles and water droplets
from the hydrocarbon stream. The liquid enters the separator, which is designed to causes
the liquid to rotate when it enters the lower section of the separator. Due to the weight
difference, the particles and water are removed by the slip stream and returned to process.
The remainder of the sample goes to the top of the separator, where a further separation is
done in the relative large volume. Water and particles will be removed from the separator by
the fast loop return at the bottom of the separator. For a further removal of water, an
additional coalescer or Teflon filter is recommended.


Different separator capacities are available for
a broad range of commercial, industrial and
consumer applications. Units are made from
316SS 4" ID pipe and can take up to 40 barg.


The separator can be used to remove particles
and water from fuel samples to process
analysers. The filter can be used as fast-loop
filter with a continuous fast-loop flow to the
standard drain connection. It is also possible
to install a manual or automatic drain valve.










Advantages are:

Delta pressure across the separator is 60-400 mbarg @ flows of 0-5 l/min.
The filter removes free water from HC streams having a minimum 0,1 SG difference.
The filter also remove particulates, down to the 3-5 micron range.


AVAILABLE MODELS


Model HLSS-2
Dimensions : A=330 mm, B= 117,5 mm
Inlet & Outlet port : " FNPT
Top & Drain port : " FNPT
Max sample temperature : 350 C
Max. working pressure : 40 barg
Flow rate : 0 5,5 l/min
All materials : 316 L Stainless steel

Model HLSS-4
Dimensions : A=406 mm, B= 117,5 mm
Inlet & Outlet port : " FNPT
Top & Drain port : " FNPT
Max sample temperature : 350 C
Max. working pressure : 40 barg
Flow rate : 0-13 l/min
All materials : 316 L Stainless steel

Model HLSS-8
Dimensions : A=546 mm, B= 117,5 mm
Inlet & Outlet port : FNPT
Top & Drain port : FNPT
Max sample temperature : 350 C
Max. working pressure : 40 barg
Flow rate : 0 24 l/min
All materials : 316 L Stainless steel

All units are shipped without fittings, ball or gate valves, plugs, etc.














1 Sample Inlet
2 Vent / Sample Outlet
3 Sample Outlet
4 Fast loop Outlet / Drain
For dimensions A and B see above models


03-08-2011 Revision 1

You might also like