TM 55-1915-251-24&P

TECHNICAL MANUAL


UNIT, DIRECT SUPPORT AND GENERAL SUPPORT
MAINTENANCE MANUAL
(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)

FOR

FM-200 FIREFIGHTING SYSTEM FOR
LOGISTICS SUPPORT VESSEL (LSV)




NSN 1915-01-153-8801










Distribution Statement A: Approved for public release. Distribution is unlimited.


HEADQUARTERS, DEPARTMENT OF THE ARMY
15 May 2003






TM 55-1915-251-24&P



WARNINGS

MODIFICATION HAZARD
Unauthorized modifications, alterations or installations of or to this equipment are prohibited and are in
violation of AR 750-10. Any such unauthorized modifications, alterations or installations could result in
death, injury or damage to the equipment.
HIGH PRESSURE SYSTEM HAZARDS
Pressurized liquid or gas systems can cause serious injuries if high pressure lines or equipment fail.

High pressure compressed air tanks, piping systems and air operated devices possess potential for
serious injury to eyes and exposed areas of shin due to escaping air pressure.
FIRE SUPPRESSANT HAZARDS
Fire suppressant chemicals displace oxygen and can cause suffocation. Immediately evacuate areas when
they are used.

After discharge, do not enter protected areas without breathing apparatus until areas are ventilated.

ELECTRICAL HAZARDS
Whenever possible, the power supply to the equipment must be shut off before beginning work on the
equipment. Do not be misled by the term "low voltage". Potentials as low as 50 volts may cause death
under adverse conditions.

Be careful not to contact 115-Vac input connections when installing or operating this equipment.

Whenever the nature of the operation permits, keep one hand away from the equipment to reduce the
hazard of current flowing through the body.
MOVING MACHINERY HAZARDS
Be very careful when operating or working near moving machinery.

Running engines, rotating shafts, and other moving machinery parts could cause personal injury or death.
FM-200 FIRE SUPPRESSANT HAZARDS
In the event the FM-200 system electric horns/strobes or the warning lights (amber strobe) are activated,
always leave the protected space immediately.
For Artificial Respiration, refer to FM 21-11.














a/(b blank)

TM 55-1915-251-24&P


INSERT LATEST CHANGED PAGES. DESTROY SUPERSEDED DATA.
LIST OF EFFECTIVE PAGES
NOTE: The portion of text affected by the changes is indicated by a vertical line in the outer margins of the
page. Changes to illustrations are indicated by miniature pointing hands. Changes to wiring diagrams are
indicated by shaded areas.
Dates of issue for original and changed pages are:

Original .. 0 .. 15 May 2003




TOTAL NUMBER OF PAGES AFFECTED IS 512 CONSISTING OF THE FOLLOWING:






































* Zero in this column indicates an original page.

A/(B blank)
Page
No.

*Change
No.


a/(b blank) ................................. 0
A/(B blank) ................................. 0
i through iv ................................. 0
Section I (6 pages)..................... 0
Section II (216 pages)............... 0
Section III (6 pages)................... 0
Section IV (14 pages) ................ 0
Section V (6 pages) ................... 0
Section VI (4 pages) .................. 0
Section VII (32 pages) ............... 0
Section VIII (104 pages) ............ 0
Section IX (104 pages) .............. 0
Auth. Page ............................... 0
Electronic 2028 .......................... 0
DA Form 2028 ........................... 0

TM 55-1915-251-24&P

TECHNICAL MANUAL HEADQUARTERS
NO. 55-1915-251-24&P DEPARTMENT OF THE ARMY
WASHINGTON D.C. 15 May 2003
TECHNICAL MANUAL
UNIT, DIRECT SUPPORT
AND GENERAL SUPPORT
MAINTENANCE MANUAL (INCLUDING
REPAIR PARTS AND SPECIAL TOOLS LIST)
FOR
FM-200 FIRE FIGHTING SYSTEM
LOGISTICS SUPPORT VESSEL (LSV)
NSN: 1915-01-153-8801

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this publication. If you find any mistakes or if you know of a way to improve the procedures,
please let us know. Submit your DA Form 2028 (Recommended Changes to Publications and Blank Forms),
through the Internet, on the Army Electronic Product Support (AEPS) website. The Intemet address is
http://aeps.ria.army.mil. If you need a password, scroll down and click on "ACCESS REQUEST FORM". The DA
Form 2028 is located in the ONLINE FORMS PROCESSING section of the AEPS. Fill out the form and click on
SUBMIT. Using this form on the AEPS will enable us to respond quicker to your comments and better manage the
DA Form 2028 program. You may also mail, fax or email your letter, or DA Form 2028 direct to: AMSTA-LC-
CI/TECH PUBS, TACOM-RI, 1 Rock Island Arsenal, Rock Island, IL 61299-7630. The email address is TACOM-
[email protected]. The fax number is DSN 793-0726 or Commercial (309) 782-0726.

Distribution Statement A: Approved for public release; Distribution is unlimited.
DESTRUCTION NOTICE - For unclassified, limited documents, destroy by any method that will prevent disclosure
of contents or reconstruction of the document.













i

TM 55-1915-251-24&P

Table of Contents
Section:

I. General Information
II. Installation, Operation and Maintenance Manual for Marine FM-200 Fire Suppression System
III. Preventive Maintenance Checks and Services (PMCS) for FM-200 and Water Washdown System (WWS)
IV. Kwik-Draw Sampling Pump Operation and Maintenance Manual with Brochure 08-00-02, Detector Tubes
and Kwik-Draw Pump
V. Appendix A Maintenance Allocation Chart (MAC)
VI. Appendix B Components of End Items (COEI) and Basic Issue Items (BII) List
VII. Appendix C Material Safety Data Sheets for: Hydrogen Fluoride (HG) Gas, FM-200, Nitrogen and Carbon
Dioxide (CO2)
VIII. Appendix D Component Manufacturers Repair Part Data Sheets for FM-200 and Water Washdown
System Installation with Distributor Listing
IX. Appendix E As Built/Installation Drawings
FO-1 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (1 of 18)
FO-2 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (2 of 18)
FO-3 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (3 of 18)
FO-4 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (4 of 18)
FO-5 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (5 of 18)
FO-6 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (6 of 18)
FO-7 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (7 of 18)
FO-8 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (8 of 18)
FO-9 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (9 of 18)
FO-10 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (10 of 18)
FO-11 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (11 of 18)
FO-12 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (12 of 18)
FO-13 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (13 of 18)
FO-14 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (14 of 18)
FO-15 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (15 of 18)
FO-16 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (16 of 18)
FO-17 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (17 of 18)
FO-18 LSV FM-200 System Piping Installation and Details. LSV-5553-1 (18 of 18)
FO-19 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (1 of 6)
FO-20 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (2 of 6)
FO-21 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (3 of 6)
FO-22 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (4 of 6)
FO-23 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (5 of 6)
FO-24 LSV FM-200 System Miscellaneous Mods. LSV-5553-2 (6 of 6)
FO-25 LSV FM-200 System Electrical Modifications. LSV-5553-3 (1 of 7)
FO-26 LSV FM-200 System Electrical Modifications. LSV-5553-3 (2 of 7)
FO-27 LSV FM-200 System Electrical Modifications. LSV-5553-3 (3 of 7)
FO-28 LSV FM-200 System Electrical Modifications. LSV-5553-3 (4 of 7)
FO-29 LSV FM-200 System Electrical Modifications. LSV-5553-3 (5 of 7)
FO-30 LSV FM-200 System Electrical Modifications. LSV-5553-3 (6 of 7)
FO-31 LSV FM-200 System Electrical Modifications. LSV-5553-3 (7 of 7)
FO-32 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (1 of 8)
FO-33 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (2 of 8)
FO-34 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (3 of 8)
FO-35 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (4 of 8)
FO-36 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (5 of 8)
FO-37 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (6 of 8)
FO-38 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (7 of 8)
FO-39 LSV FM-200 System Label Plates and Placards. LSV-5553-4 (8 of 8)



ii


TM 55-1915-251-24&P





FO-40 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (1 of 10)
FO-41 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (2 of 10)
FO-42 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (3 of 10)
FO-43 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (4 of 10)
FO-44 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (5 of 10)
FO-45 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (6 of 10)
FO-46 LSV Water Washdown System Piping Installation and Details. LSV -5231-1 (7 of 10)
FO-47 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (8 of 10)
FO-48 LSV Water Washdown System Piping Installation and Details. LSV-5231-1 (9 of 10)
FO-49 LSV Water Washdown System Piping Installation and Details. LSV -5231-1 (10 of 10)
FO-50 LSV Water Washdown System Label Plates and Placards. LSV-5231-2 (1 of 2)
FO-51 LSV Water Washdown System Label Plates and Placards. LSV-5231-2 (2 of 2)











































iii


TM 55-1915-251-24&P



SUPPLEMENTARY INTRODUCTORY MATERIAL

1-1. Maintenance Forms and Records. Department of the Army forms and procedures used for equipment
maintenance will be those described by DA PAM 738-750, The Army Maintenance Management System.

1-2. Reporting Errors and Recommending Improvements. You can help improve this manual. If you find
any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter or DA
Form 2028 (Recommended Changes to Publications and Blank Forms) located in the back of this manual
directly to: Technical Publication Information Office, TACOM-RI, 1 Rock Island Arsenal, IL 61299-7630. A
reply will be furnished directly to you.


1-3. Preparation for Storage and Shipment. Refer to Maintenance Section of the Operation and Maintenance
Manual for Fire Detection System (Pyrotronics System 3).

1-4. Destruction of Army Materiel to Prevent Enemy Use. Refer to TM 750-244-2 and TM 750-244-3 for
instructions covering the destruction of Army Materiel to Prevent enemy use.



































iv
TM 55-1915-251-24&P




















SECTION I


GENERAL INFORMATION

































TM 55-1915-251-24&P





1. GENERAL INFORMATION FOR FM-200 FIREFIGHTING SYSTEM

1.1 DESCRIPTION OF FM-200. FM-200 (1,1,1,2,3,3,3 - Heptafluoropropane is a compound of Carbon, Fluorine,
and Hydrogen (CF
3
CHFCF
3
). It is colorless, odorless, and electrically non-conductive. It suppresses fire by a
combination of chemical and physical mechanisms without affecting the available Oxygen. FM-200 is clean, leaves
no residue, thereby eliminating costly after-fire clean-up, and keeping down time to a minimum. FM-200 is stored
in steel containers, at 360 PSIG, 70F (25 bars at 21C), as a liquid, with Nitrogen added to improve the discharge
characteristics. When discharged, the FM-200 liquid vaporizes at the discharge nozzles and is uniformly
distributed as it enters the fire area. FM-200 is approved for total flooding fire extinguishing applications in
occupied spaces by the Environmental Protection Agency (EPA) and appears on the Significant New Alternatives
Policy (SNAP) list of acceptable substitutes for ozone depleting substances. FM-200 is also on the clean
halocarbon fire extinguishing agents listed in the National Fire Protection Agency (NFPA) 2001 Standard, Clean
Agent Fire Extinguishing Systems and is approved for marine application by the US Coast Guard (USCG).

1.2 INSTALLATION REQUIREMENTS. The FM-200 systems have been installed in accordance with the
approved Technical Data Package (TDP) consisting of the Detailed Design/Installation Drawings.

1.3 VESSEL SPECIFIC DESIGN CONFIGURATIONS. Due to differences in vessel configuration within the LSV
Design, minor configuration changes to the Detailed Design/Installation Drawings were made during each
installation to accommodate the configuration of each vessel. The Detailed Design/Installation Drawings have
been revised to fully disclose the as-built configuration of the FM-200 systems installed on your vessel. LSV-1-
5553-1, US Army LSV-1 FM-200 System Piping Installation and Details; LSV-1-5553-2, US Army LSV-1 FM-200
System Miscellaneous Mods; LSV-1-5553-3, US Army LSV-1 FM-200 System Electrical Modifications; and LSV-1-
5553-4, US Army LSV-1 FM-200 System Label Plates and Placards; are specific to your vessel and disclose the
as-built configuration of the installed FM-200 systems. These drawings are provided as follows:

DRAWING TITLE DRAWING NUMBER LOCATION
US Army LSV-1
FM-200 System Piping Installation and Details

LSV-1-5553-1

Appendix E
US Army LSV-1
FM-200 System Miscellaneous Mods

LSV-1-5553-2

Appendix E
US Army LSV-1
FM-200 System Electrical Modifications

LSV-1-5553-3

Appendix E
US Army LSV-1
FM-200 System Label Plates and Placards

LSV-1-5553-4

Appendix E


NOTE

AS BUILT DIFFERENCES IN VESSEL CONFIGURATION EXIST WITHIN THE
LSV DESIGN. ACTUAL LOCATION OF SOME COMPONENTS MAY VARY
SLIGHTLY BETWEEN VESSELS.


1.4 IDENTIFICATION OF PROTECTED SPACES. The FM-200 Total Flooding Fire Extinguishing Systems on
LSV consists of four (4) manually actuated systems.





1

TM 55-1915-251-24&P



CAUTION

THE INSTALLED FM-200 SYSTEMS ARE MANUALLY ACTUATED.
IT IS IMPERATIVE YOU BECOME TOTALLY VERSED IN THE OPERATION
AND MAINTENANCE OF THESE SYSTEMS.


1.4.1 ENGINE ROOM. This manually actuated system is designed and installed to protect the Engine Room and
bilge (2-84-0-E), Frames 84 to 144. The physical location of this system, less FM-200 distribution piping and
nozzles, Electric Horn/Strobe, and Warning Lights (Amber Strobe), is installed outside of the protected space
(Engine Room). Three (3) each 600 pound cylinders and supporting components, installed on the forward
bulkhead, Frame 115, Boatswain Storeroom (1-115-2-A), provide protection for the Engine Room and bilge. Three
(3) each 600 pound cylinders and supporting components, installed on the forward bulkhead, Frame 111,
Machinery Room (1-111-1-Q), provide protection for the starboard side of the Engine Room and bilge.

1.4.2 PAINT LOCKER. This manually actuated system is designed and installed to protect the Paint Locker (1-7-
3-A), main deck level, Frames 7 to 14. The physical location of this system, less FM-200 distribution piping and
nozzle and FM-200 Siren, is installed outside the protected space. One (1) each 125 pound FM-200 cylinder and
supporting components, installed on the forward bulkhead of the Bow Thruster Compartment (2-10-0-E) at Frame
22, provide protection for the Paint Locker.

1.4.3 BOW THRUSTER COMPARTMENT. This manually actuated system is designed and installed to protect
the Bow Thruster Compartment and bilge (2-10-0-E), Frames 10 to 22. The physical location of this system, less
FM-200 distribution piping and nozzles, Electric Horn/Strobe, and Warning Light (Amber Strobe), is installed
outside of the protected space. One (1) each 350 pound FM-200 cylinder and supporting components, installed in
the Paint Locker (1-7-3-A), Frame 9, provides protection for Bow Thruster Compartment and bilge.

1.4.4 EMERGENCY GENERATOR ROOM. This manually activated system is designed and installed to protect
the Emergency Generator Room (1-120-1-Q), Frames 120 to 128. The physical location of this system, less FM-
200 distribution piping and nozzles, Electric Horn/Strobe, and Warning Light (Amber Strobe), is installed outside of
the protected space. One (1) each 125 pound FM-200 cylinder and supporting components, installed in the
Machinery Room (1-111-1-Q), Frame 9, provides protection for Emergency Generator Room.


1.5 RELATED INSTALLATIONS. The Engine Room and Bow Thruster Compartment FM-200 installations are
supplemented by the installation of a Water Washdown System (WWS). This manually activated system serves to
quickly reduce compartment temperature prior to discharge of FM-200 agent, minimizes production of Hydrogen
Fluoride (HF) Gas generated as a result of FM-200 agent decomposition from contact with hot surfaces and flame
at temperatures above 1300F, aids in scrubbing of any HF Gas generated, and expedites ventilation of the
compartment.












2


TM 55-1915-251-24&P


1.6 FM-200 OPERATION INSTRUCTIONS. Operation instructions for each protected space are located in TM
55-1915-200-10, paragraph 2-63.

2. GENERAL INFORMATION FOR WATERWASHDOWN SYSTEM (WWS)

2.1 DESCRIPTION OF WWS. The WWS built of all stainless components are three (3) separate systems
installed in the Engine Room and Bow Thruster Compartment. The WWS is a hydrogen fluoride (HF) gas
mitigation, water washdown system (WWS) which provides general overhead coverage to the protected spaces.
The WWS is a simple overhead sprinkler grid which is piped directly to the existing firemain. The Engine Room
WWS receives seawater from the NO. 2 Emergency Fire Pump which is powered electrically from the emergency
buss. The Bow Thruster Compartment WWS receives seawater from either Fire Pump.

2.2 PURPOSE OF WWS. The WWS, upon activation, serves to quickly reduce the temperature within the
protected space, minimize production of Hydrogen Fluoride (HF) Gas which is produced as a result of FM-200
agent decomposition in contact with hot surfaces and flame at temperatures above 1300
o
F, aid in scrubbing of any
HF Gas generated and expedite ventilation of the protected space.


WARNING

THE WWS IS NOT DESIGNED NOR INTENDED TO BE A STAND ALONE FIRE
EXTINGUISHING SYSTEM. IT IS DESIGNED TO BE USED IN CONJUNCTION
WITH THE INSTALLED FM-200 FIXED FIRE EXTINGUISHING SYSTEM.
FAILURE TO DO SO COULD RESULT IN EQUIPMENT DAMAGE, DEATH
OR SERIOUS INJURY.


2.3 INSTALLATION. Each WWS has been installed in accordance with the approved Technical Data Package
(TDP) which consists of the Detailed Design/Installation Drawings.

2.4 VESSEL SPECIFIC DESIGN CONFIGURATIONS. Due to the differences in vessel configuration within the
LSV Design, minor configuration changes to the Detailed Design/Installation Drawings were made during each
installation to accommodate the configuration of each vessel. The Detailed Design/Installation Drawings have
been revised to fully disclose the configuration of each WWS installed on your vessel. Drawings LSV-5231-1, US
Army LSV Water Washdown System Piping Installation and Details and LSV-5231-2, US Army LSV Water
Washdown System Label Plates and Placards, which are specific to your vessel, disclose the as-built configuration
of each WWS. Drawing LSV-5231-1 and drawing LSV-5231-2 are provided at Appendix E.

2.5 OPERATION INSTRUCTIONS FOR WWS. Operation instructions for the WWS are contained in TM 55-
1915-200-10, paragraph 2-64.











3

TM 55-1915-251-24&P



3.0 PREPOSITION OR STORAGE OF VESSEL.

3.1 PLACING VESSEL IN PREPOSITION OR STORAGE: There are no required maintenance actions required
on the FM-200 systems prior to placing vessel in preposition or storage. The FM-200 cylinders may require
storage in an environmentally controlled external storage space. The FM-200 cylinders are required to be in an
environment protected from the weather, where the ambient temperature does not exceed 130F, nor fall below
32F, at all times.

3.2 REMOVING VESSEL FROM PREPOSITION OR STORAGE:

3.2.1 ENGINE ROOM FM-200 SYSTEM: Perform Item No. 1 through Item No. 6 as identified in
Preventative Maintenance Checks and Services for Engine Room FM-200 system.

3.2.2 TUNNEL FM-200 SYSTEM: Perform Item No. 1 through Item No. 6 as identified in Preventative
Maintenance Checks and Services for Tunnel FM-200 system.

3.2.3 BOW THRUSTER COMPARTMENT FM-200 SYSTEM: Perform Item No. 1 through Item No. 6 as identified
in Preventative Maintenance Checks and Services for Bow Thruster Compartment FM-200 system.

3.2.4 PAINT LOCKER FM-200 SYSTEM: Perform Item No. 1 through Item No. 5 as identified in Preventative
Maintenance Checks and Services for Paint Locker FM-200 system.

3.3 A/C AND EMERGENCY GENERATOR ROOM FM-200 SYSTEM: Perform Item No. 1 through Item No. 5 as
identified in Preventative Maintenance Checks and Services for Emergency Generator Room FM-200 system.

4.0 SERVICE AND WARRANTY INFORMATION

4.1 SCOPE OF CONTRACTOR SERVICE. The FM-200 Installation Contractor will provide three (3) years of
manufacturer recommended inspection and routine preventive maintenance services and supplies from date of
acceptance of installation. This includes annual recertification of FM-200 systems for three (3) years from date of
acceptance of installations.

4.2 ANNUAL RE-CERTIFICATION OF FM-200 SYSTEMS. Installed FM-200 systems, installed on LSV, require
annual re-certification. For annual recertification of FM-200 systems, contact Hiller Systems, Inc. directly to
schedule (see Paragraph 4.5).


NOTE

THE INITIAL INSTALLATION CONTRACT COVERS THE FIRST THREE YEARS
OF RE-CERTIFICATION SERVICES, EXCLUDING ANY REPAIR PARTS. THIS
PRE-PAID RECERTIFICATION FOR LSV SHOULD HAVE TAKEN PLACE IN
NOVEMBER 1999, NOVEMBER 2000 AND NOVEMBER 2001.







4

TM 55-1915-251-24&P



4.3 WARRANTY.

4.4 SCOPE OF CONTRACTOR WARRANTY. The FM-200 Installation Contractor will provide one (1) year
warranty on FM-200 systems parts and installation from date of acceptance of installation.

4.5 CONTRACTOR WARRANTY SERVICE. To obtain FM-200 system warranty service, contact the FM-200
systems Installation Contractor (24 hours/day):

COMPANY ADDRESS TELEPHONE FACSIMILE E-MAIL
Hiller Systems Inc. 833 Principal Lane
Chesapeake, VA
23320.
(757) 549-9123 (757) 549-1083 [email protected]

4.6 POST WARRANTY SERVICE. To obtain service or repair of FM-200 systems after warranty expiration,
contact a Kidde-Fenwal Inc. Manufacturers Certified Technician/Distributor. A world-wide listing is provided at
Section VIII.





































5/(6 blank)

TM 55-1915-251-24&P


















SECTION II


Installation, Operation and Maintenance Manual for
Marine FM-200 Fire Suppression System



















































90-FM200M-21
Version 1.0 May 1998
1

90-FM200M-21
Version 1.0 May 1998

2

90-FM200M-21
Version 1.0 May 1998
3

90-FM200M-21
Version 1.0 May 1998

4

90-FM200M-21
Version 1.0 May 1998
5

90-FM200M-21
Version 1.0 May 1998

6

90-FM200M-21
Version 1.0 May 1998
7

90-FM200M-21
Version 1.0 May 1998

8


90-FM200M-21
Version 1.0 May 1998
9



90-FM200M-21
Version 1.0 May 1998

10

90-FM200M-21
Version 1.0 May 1998
11

tube

90-FM200M-21
Version 1.0 May 1998

12

90-FM200M-21
Version 1.0 May 1998
13

90-FM200M-21
Version 1.0 May 1998

14

90-FM200M-21
Version 1.0 May 1998
15

90-FM200M-21
Version 1.0 May 1998

16

90-FM200M-21
Version 1.0 May 1998

17

90-FM200M-21
Version 1.0 May 1998

18

90-FM200M-21
Version 1.0 May 1998
19

90-FM200M-21
Version 1.0 May 1998

20

90-FM200M-21
Version 1.0 May 1998
21

90-FM200M-21
Version 1.0 May 1998

22

90-FM200M-21
Version 1.0 May 1998
23

90-FM200M-21
Version 1.0 May 1998

24


90-FM200M-21
Version 1.0 May 1998
25

90-FM200M-21
Version 1.0 May 1998

26

90-FM200M-21
Version 1.0 May 1998
27

90-FM200M-21
Version 1.0 May 1998

28

90-FM200M-21
Version 1.0 May 1998
29

90-FM200M-21
Version 1.0 May 1998

30

90-FM200M-21
Version 1.0 May 1998
31

90-FM200M-21
Version 1.0 May 1998

32

90-FM200M-21
Version 1.0 May 1998
33

90-FM200M-21
Version 1.0 May 1998

34

90-FM200M-21
Version 1.0 May 1998
35

90-FM200M-21
Version 1.0 May 1998

36 Change 1
90-FM200M-21
Version 1.0 May 1998
37

90-FM200M-21
Version 1.0 May 1998

38

90-FM200M-21
Version 1.0 May 1998
39


90-FM200M-21
Version 1.0 May 1998

40


90-FM200M-21
Version 1.0 May 1998
41

90-FM200M-21
Version 1.0 May 1998

42

90-FM200M-21
Version 1.0 May 1998
43

90-FM200M-21
Version 1.0 May 1998

44

90-FM200M-21
Version 1.0 May 1998
45

90-FM200M-021
Version 1.0 May 1998

46

90-FM200M-021
Version 1.0 May 1998

47

90-FM200M-021
Version 1.0 May 1998

48

90-FM200M-021
Version 1.0 May 1998

49

90-FM200M-021
Version 1.0 May 1998

50

90-FM200M-021
Version 1.0 May 1998

51

90-FM200M-021
Version 1.0 May 1998

52

90-FM200M-021
Version 1.0 May 1998
53

90-FM200M-021
Version 1.0 May 1998

54

90-FM200M-021
Version 1.0 May 1998
55

90-FM200M-021
Version 1.0 May 1998

56

90-FM200M-021
Version 1.0 May 1998
57

90-FM200M-021
Version 1.0 May 1998

58

90-FM200M-021
Version 1.0 May 1998
59

90-FM200M-021
Version 1.0 May 1998

60

90-FM200M-021
Version 1.0 May 1998
61

90-FM200M-021
Version 1.0 May 1998

62

90-FM200M-021
Version 1.0 May 1998
63

90-FM200M-021
Version 1.0 May 1998

64

90-FM200M-021
Version 1.0 May 1998
65

90-FM200M-021
Version 1.0 May 1998

66

90-FM200M-021
Version 1.0 May 1998
67

90-FM200M-021
Version 1.0 May 1998

68

90-FM200M-021
Version 1.0 May 1998
69

90-FM200M-021
Version 1.0 May 1998

70

90-FM200M-021
Version 1.0 May 1998
71

90-FM200M-021
Version 1.0 May 1998

72

90-FM200M-021
Version 1.0 May 1998
73

90-FM200M-021
Version 1.0 May 1998

74

90-FM200M-021
Version 1.0 May 1998
75

90-FM200M-021
Version 1.0 May 1998

76

90-FM200M-021
Version 1.0 May 1998
77

90-FM200M-021
Version 1.0 May 1998

78

90-FM200M-021
Version 1.0 May 1998
79

90-FM200M-021
Version 1.0 May 1998

80

90-FM200M-021
Version 1.0 May 1998
81

90-FM200M-012
Version 1.0 May 1998

82

90-FM200M-021
Version 1.0 May 1998
83

90-FM200M-021
Version 1.0 May 1998

84

90-FM200M-021
Version 1.0 May 1998
85

90-FM200M-021
Version 1.0 May 1998

86

90-FM200M-021
Version 1.0 May 1998
87

90-FM200M-021
Version 1.0 May 1998

88

90-FM200M-021
Version 1.0 May 1998
89

90-FM200M-021
Version 1.0 May 1998

90

90-FM200M-021
Version 1.0 May 1998
91/(92 blank)





































































































































































































































TM 55-1915-251-24&P


















SECTION III




PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
FOR FM-200 AND WATER WASHDOWN SYSTEM (WWS)



































TM 55-1915-251-24&P

PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) FOR FM-200 SYSTEM.

SYSTEM MAINTENANCE. In order to ensure each FM-200 system operates as designed and installed,
Preventive Maintenance Checks and Services (PMCS) must be performed in accordance with the following
requirements.

PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) FOR ENGINE ROOM FM-200 SYSTEM. The
following identifies the PMCS required to maintain the Engine Room FM-200 system in a fully operational condition:

Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
1 Monthly Pressure, FM-200
cylinders
Crew Check pressure gauges for proper
operating pressure. If pressure gauge
indicator is not in green, submit Work
Order to General Support (GS)
Maintenance to have cylinder recharged.
2 Monthly Liquid level, FM-200
cylinders*
Crew Take liquid level readings in accordance
with instructions contained in Section II of
this document. If liquid level is low,
submit Work Order to General Support
(GS) Maintenance to have cylinder
recharged.
3 Monthly Complete FM-200
System
Crew Inspect system components in
accordance with instructions contained in
Section II of this document. If any
component is damaged, submit Work
Order to General Support (GS)
Maintenance.
4 Quarterly Ventilation dampers and
closures
Crew Operate and service Engine Room Supply
Air Dampers (Port and Starboard), Engine
Room Exhaust Air Dampers (Port and
Starboard).
5 Quarterly Steering Gear
Compartment Sliding
Watertight Door
Crew Operate door to verify operation in
accordance with manufacturers manual.
Perform maintenance in accordance with
manufacturers maintenance instructions.
6 Semi-Annually FM-200 Pressure
Switches
Crew Ensure all diesel engines and powered
ventilation system shutdowns are in
operation. Manually raise plunger on
Pressure Switch. Confirm automatic
shutdown of operating engines and
ventilation systems. Confirm activation of
Warning Lights, Electric Horn/Strobe and
Warning Bell. Reset plunger on Pressure
Switches. If any engine or ventilation
system fails to shutdown automatically,
submit Work Order to General Support
(GS) Maintenance. If any Warning Lights,
Electric Horn/Strobe or Warning Bell fail
to operate, repair component.





1
TM 55-1915-251-24&P


Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
7 Annually Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
perform Annual Recertification.
8 Post system
disassembly
FM-200 piping and
distribution system
General Support Perform test of FM-200 piping and
distribution system per testing
requirements identified on Drawing LSV-
1-5553-1.
9 Post system
activation
Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
request System Recertification.

* Note - Refer to the Kidde Fire Systems FM-200 ECS Series Engineered Design, Installation, Operation
and Maintenance Manual for Marine FM-200 Systems for temperature correction charts.



PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) FOR PAINT LOCKER FM-200 SYSTEM. The
following identifies the PMCS required to maintain the Paint Locker FM-200 system in a fully operational condition:

Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
1 Monthly Pressure, FM-200
cylinder
Crew Check pressure gauge for proper
operating pressure. If pressure gauge
indicator is not in green, submit Work
Order to General Support (GS)
Maintenance to have cylinder recharged.
2 Monthly Complete FM-200
System
Crew Inspect system components in
accordance with instructions contained in
Section II of this document. If any
component is damaged, submit Work
Order to General Support (GS)
Maintenance.
3 Semi-Annually FM-200 Pressure
Switch
Crew Ensure powered ventilation system
shutdown is in operation. Manually raise
plunger on Pressure Switch. Confirm
automatic shutdown of ventilation
system. Confirm activation of Warning
Bell. Reset plunger on Pressure Switch.
If ventilation system fails to operate,
summit work order to General Support
(GS) Maintenance. If Warning Bell fails
to operate, repair Warning Bell.
4 Annually Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
perform Annual Recertification.
5 Post system
disassembly
FM-200 piping and
distribution system
General Support Test piping and distribution system per
testing requirements identified on
Drawing LSV-1-5553-1
6 Post system
activation
Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative to
perform System Recertification.

2
TM 55-1915-251-24&P


PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) FOR BOW THRUSTER COMPARTMENT
FM-200 SYSTEM. The following identifies the PMCS required to maintain the Bow Thruster Room FM-200 system
in a fully operational condition:
Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
1 Monthly Pressure, FM-200
cylinders
Crew Check pressure gauges for proper
operating pressure. If pressure gauge
indicator is not in green, submit Work
Order to General Support (GS)
Maintenance to have cylinder recharged.
2 Monthly Liquid level, FM-200
cylinders*
Crew Take liquid level readings in accordance
with instructions contained in Section II of
this document. If liquid level is low,
submit Work Order to General Support
(GS) Maintenance to have cylinder
recharged.
3 Monthly Complete FM-200
System
Crew Inspect system components in
accordance with instructions contained in
Section II of this document. If any
component is damaged, submit Work
Order to General Support (GS)
Maintenance.
4 Quarterly Ventilation dampers Crew Verify proper operation of and service
Supply Damper and Exhaust Damper
5 Semi-Annually FM-200 Pressure
Switches
Crew Ensure diesel engine and powered
ventilation system shutdowns are in
operation. Manually raise plunger on
Pressure Switches. Confirm automatic
shutdown of operating engine and
ventilation system. Confirm activation of
Warning Light, Electric Horn/Strobe and
Warning Bell. Reset plunger on Pressure
Switches. If diesel engine or ventilation
system fails to shutdown automatically,
submit Work Order to General Support
(GS) Maintenance. If any Warning Lights,
Electric Horn/Strobe or Warning Bell fails
to operate, repair component.
6 Annually Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
perform Annual Recertification.
7 Post system
disassembly
FM-200 piping and
distribution system
General Support Perform test of FM-200 piping and
distribution system per testing
requirements identified on Drawing LSV-
5553-1.
8 Post system
activation
Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
request System Recertification.

* Note - Refer to the Kidde Fire Systems FM-200 ECS Series Engineered Design, Installation, Operation
and Maintenance Manual for Marine FM-200 Systems (This document is provided at Section II) for temperature
correction charts.




3


TM 55-1915-251-24&P

PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) FOR EMERGENCY GENERATOR ROOM
FM-200 SYSTEM. The following identifies the PMCS required to maintain the Emergency Generator Room FM-
200 system in a fully operational condition:

Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
1 Monthly Pressure, FM-200
cylinder
Crew Check pressure gauge for proper
operating pressure. If pressure gauge
indicator is not in green, submit Work
Order to General Support (GS) Maint.
to have cylinder recharged.
2 Monthly Complete FM-200
System
Crew Inspect system components in
accordance with instructions contained
in Section II of this document. If any
component is damaged, submit Work
Order to General Support (GS) Maint.
3 Quarterly Ventilation Damper Crew Verify proper operation and service
Emergency Generator Room Supply Air
Damper.
4 Quarterly Ventilation Covers Crew Install three (3) ventilation covers (Stbd.
Mooring Station). Verify fit and service
securements.
5 Semi-Annually FM-200 Pressure
Switches
Crew Ensure diesel engine and powered
ventilation system shutdowns are in
operation. Manually raise plunger on
Pressure Switches. Confirm automatic
shutdown of diesel engine and
ventilation system. Confirm activation
of Warning Light, Electric Horn/Strobe,
and Warning Bell. Reset plunger on
Pressure Switches. If diesel engine or
ventilation system fail to shutdown
automatically, submit Work Order to
General Support (GS) Maintenance. If
Warning Light, Electric Horn/Strobe, or
Warning Bell fails to operate, repair
component.
6 Annually Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
perform Annual Recertification.
7 Post system
disassembly
FM-200 piping and
distribution system
General Support Perform test of FM-200 piping and
distribution system per testing
requirements identified on Drawing
LSV-1-5553-1.
8 Post system
activation
Complete FM-200
system
General Support Obtain services of Manufacturers
Certified Technical Representative and
request System Recertification.









4


TM 55-1915-251-24&P


PREVENTIVE MAINTENANCE CHECKS AND SERVICES FOR WATER WASHDOWN SYSTEM (WWS)

The following provides the preventive maintenance checks and services required to maintain each WWS in a fully
operational condition:

Item
No.

Interval

Item to be Inspected
Maintenance
Level

Procedure
1 Weekly Control valve Crew Charge fire main to operating pressure,
perform a visual inspection to verify WWS is
free of leaks. If leaks are discovered, repair
Control Valve.
2 Monthly Control valve Crew Verify fire main is not charged.
Inspect control valve handle locking
mechanism to ensure it is free and operates
properly. Exercise WWS control valve by
unlocking valve handle and operating control
valve through two (2) openings and closings.
Close valve and verify lock is engaged. If
control valve fails to operate, repair or
replace.
3 Monthly Strainer blow off

Crew Verify fire main is not charged.
Exercise WWS strainer blow off procedure
through two (2) openings and closings. Leave
WWS strainer blow off valve in closed
position. If valve fails to operate, replace
valve.
4 Post system
disassembly
Complete system General
Support
Test the system per testing requirements
identified on Drawing LSV-5231-1. If system
fails to meet test requirements, repair system,
and retest system.
5 Triennial Control valve, strainer,
and piping
General
Support
Perform a flow test. Refer to drawing LSV-
5231-1 for system flow requirements. If
system fails to meet flow requirements, repair
Bow Thruster Emergency Fire Pump and/or
Engine Room Fire Pump(s) and retest.
6 Post system
activation
Strainer Crew Remove, clean, and reinstall strainer basket.


















5/(6 blank)

TM 55-1915-251-24&P













SECTION IV

Kwik-Draw Sampling Pump Operation and Maintenance
Manual/w Brochure 08-00-02, Detector Tubes and Kwik-Draw Pump


































































TM 55-1915-251-24&P


















SECTION V


Appendix A Maintenance Allocation Chart (MAC)






































TM 55-1915-251-24&P

UNIT, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE FM-200
FIREFIGHTING SYSTEM AND WATER WASHDOWN SYSTEM (WWS)
MAINTENANCE ALLOCATION CHART



MAINTENANCE ALLOCATION CHART (MAC)

A-1 INTRODUCTION

The Army Maintenance System MAC

This introduction provides a general explanation of all maintenance and repair functions authorized at various
maintenance levels under the standard Army Maintenance System concept.

The MAC (immediately following the introduction) designates overall authority and responsibility for the
performance of maintenance functions on the identified end item or component. The application of the
maintenance functions to the end item or component shall be consistent with the capacities and capabilities of
the designated maintenance levels, which are shown on the MAC in column (4) as:

Unit includes two subcolumns, C (operator/crew) and O (unit) maintenance.

Direct Support includes an F subcolumn.

General Support includes an H subcolumn.

Depot includes a D subcolumn.

The tools and test equipment requirements (immediately following the MAC) list the tools and test equipment
(both special tools and common tool sets) required for each maintenance function as referenced from the MAC.

The remarks (immediately following the tools and test equipment requirements) contain supplemental
instructions and explanatory notes for a particular maintenance function.

A-2 Maintenance Functions

Maintenance functions are limited to and defined as follows:

1. Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical
characteristics with established standards through examination; e.g., by sight, sound, or feel.

2. Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics
of an item and comparing those characteristics with prescribed standards on a scheduled basis.

3. Service. Operations required periodically to keep an item in proper operating condition; e.g., to clean
(includes decontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants,
hydraulic fluids, or gases.

4. Adjust. To maintain or regulate, within prescribed limits, by bringing into proper position, or by setting the
operating characteristics to specified parameters.

5. Align. To adjust specified variable elements of an item to bring out optimum or desired performance.

6. Calibrate. To determine and cause corrections to be made or to be adjusted on instruments of test,
measuring, and diagnostic equipment used in precision measurement. Consists of comparisons of two
instruments, one of which is a certified standard of known accuracy, to detect and adjust any discrepancy in
the accuracy of the instrument being compared.


A-1
TM 55-1915-251-24&P


7. Remove/Install. To remove and install the same item when required to perform service or other
maintenance functions. Install may be the act of emplacing, seating, or fixing into position a spare, repair
part, or module (component or assembly) in a manner to allow the proper functioning of equipment or a
system.

8. Replace. To remove an unserviceable item and install a serviceable counterpart in its place. Replace is
authorized by the MAC and assigned maintenance level is shown as the third position code of the Source,
Maintenance and Recoverability (SMR) code.

9. Repair. The application of maintenance services, including fault location/troubleshooting,
removal/installation, disassembly/assembly procedures, and maintenance actions to identify troubles and
restore serviceability to an item by correcting specific damage, fault, malfunction, or failure in a part,
subassembly, module (component or assembly), end item, or system.

NOTE

The following definitions are applicable to the Repair maintenance function:

Services Inspect, test, service, adjust, align, calibrate, and/or replace.

Fault location/troubleshooting The process of investigating and detecting the cause of
equipment malfunctioning; the act of isolating a fault within a system or Unit Under Test
(UUT).

Disassembly/assembly The step-by-step breakdown (taking apart) of a
spare/functional group coded item to the level of its least component that is assigned
an SMR code for the level of maintenance under consideration (i.e., identified as
maintenance significant).

Actions Welding, grinding, riveting, straightening, facing, machining, and/or
resurfacing.

10. Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely
serviceable/operational condition as required by maintenance standards in appropriate technical
publications. Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul
does not normally return an item to like new condition.

11. Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a
like new condition in accordance with original manufacturing standards. Rebuild is the highest degree of
material maintenance applied to Army equipment. The rebuild operation includes the act of returning to zero
those age measurements (e.g., hours/miles) considered in classifying Army equipment/components.

A-3 Explanation of Columns in the MAC

Column (1) Group Number. Column (1) lists functional group code (FGC) numbers, the purpose of which is to
identify maintenance significant components, assemblies, subassemblies, and modules with the Next Higher
Assembly (NHA). End item group number shall be 00.

Column (2) Component/Assembly. Column (2) contains the item names of components, assemblies,
subassemblies, and modules for which maintenance is authorized.

Column (3) Maintenance Function. Column (3) lists the functions to be performed on the item listed in column
(2). (For a detailed explanation of these functions refer to Maintenance Functions outlined above.)




A-2
TM 55-1915-251-24&P

Column (4) Maintenance Level. Column (4) specifies each level of maintenance authorized to perform each
function listed in column (3), by indicating work time required (expressed as man-hours in whole hours or
decimals) in the appropriate sub-column. This work time figure represents the active time required to perform
that maintenance function at the indicated level of maintenance. If the number or complexity of the tasks within
the listed maintenance function varies at different maintenance levels, appropriate work time figures are to be
shown for each level. The work time figure represents the average time required to restore an item (assembly,
subassembly, component, module, end item, or system) to a serviceable condition under typical field operating
conditions. This time includes preparation time (including any necessary disassembly/assembly time),
troubleshooting/fault location time, and quality assurance time in addition to the time required to perform the
specific tasks identified for the maintenance functions authorized in the MAC. The symbol designations for the
various maintenance levels are as follows:

C Operator or crew maintenance

O Unit maintenance

F Direct support maintenance

L Specialized repair activity (SRA)

H General support maintenance

D Depot maintenance

NOTE

The L maintenance level is not included in column (4) of the MAC. Functions to this
level of maintenance are identified by a work time figure in the H column of column
(4), and an associated reference code is used in the REMARKS column (6). This code
is keyed to the remarks and the SRA complete repair application is explained there.

Column (5) Tools and Test Equipment Reference Code. Column (5) specifies, by code, those common tool
sets (not individual tools), common Test, Measurement and Diagnostic Equipment (TMDE), and special tools,
special TMDE and special support equipment required to perform the designated function. Codes are keyed to
the entries in the tools and test equipment table.

Column (6) Remarks Code. When applicable this column contains a letter code, in alphabetical order, which
is keyed to the remarks table entries.

A-4 Explanation of Columns in the Tool and Test Equipment Requirements

Column (1) Tool or Test Equipment Reference Code. The tool or test equipment reference code correlates
with a code used in column (5) of the MAC.

Column (2) Maintenance Level. The lowest level of maintenance authorized to use the tool or test equipment.


A-3
TM 55-1915-251-24&P

Column (3) Nomenclature. Name or identification of the tool or test equipment.

Column (4) National Stock Number (NSN). The NSN of the tool or test equipment.
Column (5) Tool Number. The manufacturers part number, model number, or type number.

A-5 Explanation of Columns in the Remarks

Column (1) Remarks Code. The code recorded in column (6) of the MAC.

Column (2) Remarks. This column lists information pertinent to the maintenance function being performed as
indicated in the MAC.
















































A-4
TM 55-1915-251-24&P


Section I Maintenance Allocation Chart for FM-200 Fire Fighting Systems
(1) (2) (3) (4)
MAINTENANCE LEVEL
(5) (6)
GROUP
NUMBER COMPONENT/ASSEMBLY
MAINTENANCE
FUNCTION UNIT
DIRECT
SUPPORT
GENERAL
SUPPORT DEPOT
TOOLS &
TEST
EQUIPMENT
REF CODE
REMARKS
CODE
C O F H D
18 Basic Craft Inspect 100 A
Test 2.0
Replace 100.0
Repair 10.0 10.0 40.0 80.0

1821 FM-200 Fire Fighting System Test 1.0 1.0 1, 2, 3
Inspect 1.0
Service 0.5 1.0
Repair 0.5 1.0

1821 Water Washdown System Test 1.0
(WWS) Inspect 1.0
Service 0.5 1.0


Section II Tools and Test Equipment for FM-200 Fire Fighting Systems
TOOL OR TEST
EQUIPMENT REF
CODE
MAINTENANCE
LEVEL
NOMENCLATURE NATIONAL STOCK
NUMBER
TOOL NUMBER
1 C Kwik-Draw Deluxe Detector Tube Pump w/
End of Stroke Indicator, Remote Sampling
Adapter, and Carrying Pouch
(7L021) 487500
2 C Detector Tube, Hydrogen Fluoride Gas
(HF-1), 125 ppm Range, 3 ppm Threshold
Limit Value (TLV)
(7L021) 804142
3 C Sampling Line, 10 feet long (7L021) 73076






A-5

TM 55-1915-251-24&P

Section III REMARKS
REMARKS
CODE REMARKS
A BASIC CRAFT MAC GROUP 18 LISTED FOR TRACKING INFORMATION ONLY

































A-6
TM 55-1915-251-24&P


















SECTION VI


APPENDIX B COMPONENTS OF END ITEMS (COEI)
AND BASIC ISSUE ITEMS (BII) LIST































TM 55-1915-251-24&P


COMPONENTS OF END ITEM (COEI) AND BASIC ISSUE ITEMS (BII) LISTS

INTRODUCTION

B-1 Scope

This section lists COEI and BII for the FM-200 and Water Washdown System (WWS) to help inventory items for
safe and efficient operation of the equipment.

B-2 General

The COEI and BII information is divided into the following lists:

Components of End Item (COEI). This list is for informational purposes only, and is not authority to requisition
replacements. These items are part of the FM-200 and WWS. As part of the end item, these items must be with
the end item whenever it is issued or transferred between property accounts. Items of COEI are removed and
separately packaged for transportation or shipment only when necessary. Illustrations are furnished to help you
find and identify the items.

Basic Issue Items (BII). These essential items are required to place the FM-200 and WWS in operation, operate it,
and to do emergency repairs. Although shipped separately packaged, BII must be with the FM-200 and WWS
during operation and when it is transferred between property accounts. Listing these items is your authority to
request/requisition them for replacement based on authorization of the end item by TOE/MTOE. Illustrations are
furnished to help find and identify the items.

B-3 Explanation of Columns in the COEI List and BII List

Column (1) Illus Number. Gives you the number of the item illustrated.

Column (2) National Stock Number (NSN). Identifies the stock number of the item to be used for requisitioning
purposes.

Column (3) Description, CAGEC, and Part Number. Identifies the Federal item name (in all capital letters)
followed by a minimum description when needed. The stowage location of COEI and BII is also included in this
column. The last line below the description is the CAGEC (commercial and Government entity code) (in
parentheses) and the part number.

Column (4) Usable on Code. When applicable, gives you a code if the item you need is not the same for different
models of equipment.

Column (5) Unit of Measure (U/M). Indicates the physical measurement or count of the item as issued per the
NSN shown in column (2).

Column (6) Qty Rqr. Indicates the quantity required.













B-1
TM 55-1905-251-24&P



Table B-1. Components of End Item List.

None


Table B-1. Continued - Onboard Spares FM-200


(1)
ILLUS
NUMBER
(2)
NATIONAL
STOCK
NUMBER (NSN)
(3)
DESCRIPTION, CAGEC AND
PART NO.
(4)
USABLE
ON
CODE
(5)
UNIT OF
MEASURE
(U/M)
(6)
QTY
RQR.
Dwg.
LSV-1-
5553-1
Find 81




REPLACEMENT GLASS, PULL BOX,
(1DA54) 31302



EA

2
Dwg.
LSV-1-
5553-1
Find 87


REPLACEMENT GLASS, PULL BOX,
(1DA54) 928103



EA

2


Dwg.
LSV-1-
5555-1
Find
Various


SEAL WIRE
(1DA54) 15262



EA

12


Table B-1. Continued - Onboard Spares WWS


(1)
ILLUS
NUMBER
(2)
NATIONAL
STOCK
NUMBER (NSN)
(3)
DESCRIPTION, CAGEC AND
PART NO.
(4)
USABLE
ON
CODE
(5)
UNIT OF
MEASURE
(U/M)
(6)
QTY
RQR.
Dwg.
LSV-5231-1
Find 5




NOZZLE, SPRAY, MODEL TF, 120
DEGREE, FULL CONE, MPT ,
CRES (99134) TF10



EA

2
Dwg.
LSV-5231-1
Find 79


GUARD, SPRINKLER
(7N423) SPC1



EA

2















B-2
TM 55-1915-251-24&P




Table B-2. Basic Issue Items List.

(1)
ILLUS.
NUMBER

(2)
NATIONAL
STOCK
NUMBER

(3) (4)
DESCRIPTION, CAGEC USABLE
AND PART NUMBER ON CODE

(5)
U/M

(6)
QTY
RQR.

1

TECHNICAL MANUAL, UNIT, DIRECT SUPPORT, AND
GENERAL SUPPORT MAINTENANCE FM-200 FIRE
FIGHTING SYSTEM FOR LSV
TM 55-1915-251-24&P


EA

1










































B-3/(B-4 blank)

TM 55-1915-251-24&P


















SECTION VII


Appendix C
Material Safety Data Sheets for Hydrogen
Fluoride (HG) Gas, FM-200, Nitrogen and
Carbon Dioxide (CO2)
































































































TM 55-1915-251-24&P


















SECTION VIII


Appendix D Component Manufacturers Repair Part
Data Sheets for
FM-200 and Water Washdown System Installation
with Distributor Listing































































































































































































































































































































































GEORGIA (COND)

Company Telephone Facsimile

Fire Systems, Inc. 770-333-7979 770-333-9954
4700 Highlands Pkwy
Smyrna, GA 30082
HAWAII

Company Telephone Facsimile

Fire Master, Honolulu 808-591-9256 808-596-2860
949 Kawaiaheo Street
Honolulu, HI 96814
IDAHO

Company Telephone Facsimile

General Fire, Inc. 208-344-8711 208-342-1882
4021 Overland Road
Boise, ID 83705
ILLINOIS

Company Telephone Facsimile

Illinois Fire Extinguisher Co., Inc. 630-629-2413 630-629-3006
702 South Highway 53
Addison, IL 60101

Reliable Fire Equipment 708-597-4600 708-389-1150
12845 South Cicero
Alsip, IL 60685

Fredriksen & Sons Fire Equipment 630-595-9500 630-595-3548
760 Thomas Drive
Bensenville, IL 60106

Fox Valley Fire & Safety Co. 847-695-5990 847-695-3699
1730 Berkley Ave.
Elgin, IL 60123

Fire-Safety Sales & Service 618-254-2323 618-254-0713
420 N. Wood River Ave.,
P.O. Box 45
Wood River, IL 62095
INDIANA
Company Telephone Facsimile
Fire Systems, Inc. 219-484-2531 219-484-2533
1901 Production Road
Fort Wayne, IN 46808-3647

Jacob Dietz Co. 317-631-2304 317-631-3117
2708 E. Michigan Street
Indianapolis, IN 46201








6


















































TM 55-1915-251-24&P


















SECTION IX


Appendix E As Built/Installation Drawings







































TM 55-1915-251-24&P







The as-built drawings contained in this section are LSV vessel class drawings.

Some FM-200 components are both vessel/hull number unique and system location specific. These
components are not interchangeable.

Reference specific set of vessel/hull number as-built drawings to determine correct FM-200 component
part number and system installation location.














































E-1/(E-2 blank)

TM 55-1915-251-24&P

FO-1
FP-1/(FP-2 blank)

TM 55-1915-251-24&P


FO-2
FP-3/(FP-4 blank)
TM 55-1915-251-24&P

FO-3
FP-5/(FP-6 blank)

TM 55-1915-251-24&P

FO-4
FP-7/(FP-8 blank)


TM 55-1915-251-24&P

FO-5
FP-9/(FP-10 blank)

TM 55-1915-251-24&P

FO-6
FP-11/(FP-12 blank)
TM 55-1915-251-24&P

FO-7
FP-13/(FP-14 blank)
TM 55-1915-251-24&P

FO-8
FP-15/(FP-16 blank)
TM 55-1915-251-24&P

FO-9
FP-17/(FP-18 blank)
TM 55-1915-251-24&P

FO-10
FP-19/(FP-20 blank)
TM 55-1915-251-24&P

FO-11
FP-21/(FP-22 blank)
TM 55-1915-251-24&P

FO-12
FP-23/(FP-24 blank)
TM 55-1915-251-24&P

FO-13
FP-25/(FP-26 blank)
TM 55-1915-251-24&P

FO-14
FP-27/(FP-28 blank)
TM 55-1915-251-24&P

FO-15
FP-29/(FP-30 blank)
TM 55-1915-251-24&P

FO-16
FP-31/(FP-32 blank)
TM 55-1915-251-24&P

FO-17
FP-33/(FP-34 blank)


TM 55-1915-251-24&P

FO-18
FP-35/(FP-36 blank)

TM 55-1915-251-24&P

FO-19
FP-37/(FP-38 blank)
TM 55-1915-251-24&P

FO-20
FP-39/(FP-40 blank)
TM 55-1915-251-24&P

FO-21
FP-41/(FP-42 blank)
TM 55-1915-251-24&P

FO-22
FP-43/(FP-44 blank)

TM 55-1915-251-24&P

FO-23
FP-45/(FP-46 blank)
TM 55-1915-251-24&P

FO-24
FP-47/(FP-48 blank)

TM 55-1915-251-24&P

FO-25
FP-49/(FP-50 blank)
TM 55-1915-251-24&P

FO-26
FP-51/(FP-52 blank)
TM 55-1915-251-24&P

FO-27
FP-53/(FP-54 blank)

TM 55-1915-251-24&P

FO-28
FP-55/(FP-56 blank)


TM 55-1915-251-24&P

FO-29
FP-57/(FP-58 blank)

TM 55-1915-251-24&P

FO-30
FP-59/(FP-60 blank)
TM 55-1915-251-24&P

FO-31
FP-61/(FP-62 blank)
TM 55-1915-251-24&P

FO-32
FP-63/(FP-64 blank)
TM 55-1915-251-24&P

FO-33
FP-65/(FP-66 blank)
TM 55-1915-251-24&P

FO-34
FP-67/(FP-68 blank)
TM 55-1915-251-24&P

FO-35
FP-69/(FP-70 blank)
TM 55-1915-251-24&P

FO-36
FP-71/(FP-72 blank)
TM 55-1915-251-24&P

FO-37
FP-73/(FP-74 blank)
TM 55-1915-251-24&P

FO-38
FP-75/(FP-76 blank)
TM 55-1915-251-24&P

FO-39
FP-77/(FP-78 blank)

TM 55-1915-251-24&P

FO-40
FP-79/(FP-80 blank)
TM 55-1915-251-24&P

FO-41
FP-81/(FP-82 blank)
TM 55-1915-251-24&P

FO-42
FP-83/(FP-84 blank)

TM 55-1915-251-24&P

FO-43
FP-85/(FP-86 blank)


TM 55-1915-251-24&P

FO-44
FP-87/(FP-88 blank)

TM 55-1915-251-24&P

FO-45
FP-89/(FP-90 blank)
TM 55-1915-251-24&P

FO-46
FP-91/(FP-92 blank)
TM 55-1915-251-24&P

FO-47
FP-93/(FP-94 blank)
TM 55-1915-251-24&P

FO-48
FP-95/(FP-96 blank)
TM 55-1915-251-24&P

FO-49
FP-97/(FP-98 blank)
TM 55-1915-251-24&P

FO-50
FP-99/(FP-100 blank)
TM 55-1915-251-24&P

FO-51
FP-101/(FP-102 blank)

TM 55-1915-251-24&P





















DISTRIBUTION: To be distributed in accordance with Initial Distribution Number (IDN) 115875
Requirements for TM 55-1905-251-24&P.








































By Order of the Secretary of the Army:
ERIC K. SHINSEKI
General, United States Army
Chief of Staff Official:
JOEL B. HUDSON
Administrative Assistant to the
Secretary of the Army
0223102




These are the instructions for sending an electronic 2028

The following format must be used if submitting an electronic 2028. The subject line must be
exactly the same and all fields must be included; however only the following fields are
mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27.

From: "Whomever" <[email protected]>
To: [email protected]

Subject: DA Form 2028
1. From: Joe Smith
2. Unit: home
3. Address: 4300 Park
4. City: Hometown
5. St: MO
6. Zip: 77777
7. Date Sent: 19-OCT-93
8. Pub no: 55-2840-249-23
9. Pub Title: TM
10. Publication Date: 04-JUL-85
11. Change Number: 7
12. Submitter Rank: MSG
13. Submitter FName: Joe
14. Submitter MName: T
15. Submitter LName: Smith
16. Submitter Phone: 123-123-1234
17. Problem: 1
18. Page: 1
19. Paragraph: 3
20. Line: 4
21. NSN: 5
22. Reference: 6
23. Figure: 7
24. Table: 8
25. Item: 9
26. Total: 123
27. Text:
This is the text for the problem below line 27.






















FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)
15 October 2002 TM 55-1915-251-24&P



TM 55-1915-251-24&P
FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)
15 October 2002
FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)
15 October 2002 TM 55-1915-251-24&P

TM 55-1915-251-24&P
15 October 2002
FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)

TM 55-1915-251-24&P
15 October 2002
FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)

TM 55-1915-251-24&P FM-200 Fire Fighting System for Logistics
Support Vessel (LSV)
15 October 2002
The Metric System and Equivalents

Linear Measure Liquid Measure

1 centimeter = 10 millimeters = .39 inch 1 centiliter = 10 milliliters = .34 fl. ounce
1 decimeter = 10 centimeters = 3.94 inches 1 deciliter = 10 centiliters = 3.38 fl. ounces
1 meter =10 decimeters = 39.37 inches 1 liter =10 deciliters = 33.81 fl. ounces
1 dekameter =10 meters = 32.8 feet 1 dekaliter =10 liters = 2.64 gallons
1 hectometer =10 decameters = 328.08 feet 1 hectoliter = 10 dekaliters = 26.42 gallons
1 kilometer =10 hectometers = 3,280.8 feet 1 kiloliter =10 hectoliters = 264.18 gallons

Weights Square Measure

1 centigram = 10 milligrams = .15 grain 1 sq. centimeter = 100 sq. millimeters = .155 sq. inch
1 decigram = 10 centigrams = 1.54 grains 1 sq. decimeter = 100 sq. centimeters =15.5 sq. inches
1 gram = 10 decigrams = .035 ounce 1 sq. meter (centare) = 100 sq. decimeters = 10.76 sq. feet
1 dekagram = 10 grams = .35 ounce 1 sq. dekameter (are) =100 sq. meters = 1,076.4 sq. feet
1 hectogram = 10 dekagrams = 3.52 ounces 1 sq. hectometer (hectare) = 100 sq. dekameters = 2.47
acres
1 kilogram = 10 hectograms = 2.2 pounds 1 sq. kilometer = 100 sq. hectometers = .386 sq. mile
1 quintal = 100 kilograms = 220.46 pounds
1 metric ton =10 quintals = 1.1 short tons Cubic Measure

1 cu. centimeter = 1000 cu. millimeters = .06 cu. inch
1 cu. decameter =1000 cu. centimeters = 61.02 cu. inches
1 cu. meter =1000 cu. decimeters = 35.31 feet


Approximate Conversion Factors

To change To Multiply by To change To Multiply by
inches centimeters 2.540 ounce-inches newton-meters .007062
feet meters .305 centimeters inches .394
yards meters .914 meters feet 3.280
miles kilometers 1.609 meters yards 1.094
square inches square centimeters 6.451 kilometers miles .621
square feet square meters .093 square centimeters square inches .155
square yards square meters .836 square meters square feet 10.764
square miles square kilometers 2.590 square meters square yards 1.196
acres square hectometers .405 square kilometers square miles .386
cubic feet cubic meters .028 square hectometers acres 2.471
cubic yards cubic meters .765 cubic meters cubic feet 35.315
fluid ounces milliliters 29.573 cubic meters cubic yards 1.308
pints liters .473 milliliters fluid ounces .034
quarts liters .946 liters pints 2.113
gallons liters 3.785 liters quarts 1.057
ounces grams 28.349 liters gallons .264
pounds kilograms .454 grams ounces .035
short tons metric tons .907 kilograms pounds 2.205
pound-feet newton-meters 1.356 metric tons short tons 1.102
pound-inches newton-meters .11296


Temperature (Exact)

F Fahrenheit 5/9 (after Celsius C
temperature subtracting 32) temperature
























































PIN: 080182-000
This fine document...
Was brought to you by me:
Liberated Manuals -- free army and government manuals
Why do I do it? I am tired of sleazy C-!"M sellers# $ho ta%e &ublicly
available information# sla& '$atermar%s( and other )un% on it# and sell it.
Those masters of search engine mani&ulation ma%e sure that their sites that
sell free information# come u& first in search engines. They did not create it...
They did not even scan it... Why should they get your money? Why are not
letting you give those free manuals to your friends?
I am setting this document *!++. This document $as made by the ,-
.overnment and is /"T &rotected by Co&yright. *eel free to share#
re&ublish# sell and so on.
I am not as%ing you for donations# fees or handouts. If you can# &lease
&rovide a lin% to liberatedmanuals.com# so that free manuals come u& first in
search engines:
<A HREF=http://www.liberatedmanuals.com/>Free Military and o!ernment Manuals</A>
"incerely
#$or %hudo!
http://i$or.chudo!.com/