1 - 12 CCNP: Building Multilayer Switched Networks v5.

0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

Lab 3-4 Multiple Spanning Tree


Objective
The purpose of this lab is to observe the behavior of MST (multiple
spanning tree).
Scenario
Four switches have just been installed. The distribution layer switches are
Catalyst 3560s, and the access layer switches are Catalyst 2960s. There
are redundant uplinks between the access layer and distribution layer.
Because of the possibility of bridging loops, spanning tree logically
removes any redundant links. In this lab, we will group VLANs using MST
so that we can have less spanning tree instances running at once to save
switch CPU load.
Step 1
Start by deleting vlan.dat, erasing the startup configuration, and reloading
your switches. After reloading the switches, give them hostnames.
Configure ports f0/7 through f0/12 to be trunks. On the 3560s, you first
need to set the trunk encapsulation to dot1q. On the 2960s, only dot1q is
supported, so it does not need to be set, but the mode still needs to be
changed to trunk. If you do not set the mode of the ports to be trunk, the
2 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

links do not form trunks and remain access ports (default mode on a 3560
or 2960 is dynamic auto; default mode on a 3550 or 2950 is dynamic
desirable).
DLS1#conf i gur e t er mi nal
Ent er conf i gur at i on commands, one per l i ne. End wi t h CNTL/ Z.
DLS1( conf i g) #i nt er f ace r ange f 0/ 7 - 12
DLS1( conf i g- i f - r ange) #swi t chpor t t r unk encapsul at i on dot 1q
DLS1( conf i g- i f - r ange) #swi t chpor t mode t r unk
Step 2
Configure all switches with VTP mode transparent and VTP domain
CISCO. Add VLANs 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100 to all of
them. Use the show vlan brief command to view the VLAN
configurations.
DLS1#conf i gur e t er mi nal
Ent er conf i gur at i on commands, one per l i ne. End wi t h CNTL/ Z.
DLS1( conf i g) #vtp mode transparent
Set t i ng devi ce t o VTP TRANSPARENT mode.
DLS1( conf i g) #vtp domain CISCO
Changi ng VTP domai n name f r omNULL t o CI SCO
DLS1( conf i g) #vl an 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
DLS1( conf i g- vl an) #end
DLS1#show vl an br i ef
00: 11: 56: %SYS- 5- CONFI G_I : Conf i gur ed f r omconsol e by consol e

VLAN Name St at us Por t s
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 def aul t act i ve Fa0/ 1, Fa0/ 2, Fa0/ 3, Fa0/ 4
Fa0/ 5, Fa0/ 6, Fa0/ 7, Fa0/ 8
Fa0/ 9, Fa0/ 10, Fa0/ 11, Fa0/ 12
Fa0/ 13, Fa0/ 14, Fa0/ 15, Fa0/ 16
Fa0/ 17, Fa0/ 18, Fa0/ 19, Fa0/ 20
Fa0/ 21, Fa0/ 22, Fa0/ 23, Fa0/ 24
Gi 0/ 1, Gi 0/ 2
10 VLAN0010 act i ve
20 VLAN0020 act i ve
30 VLAN0030 act i ve
40 VLAN0040 act i ve
50 VLAN0050 act i ve
60 VLAN0060 act i ve
70 VLAN0070 act i ve
80 VLAN0080 act i ve
90 VLAN0090 act i ve
100 VLAN0100 act i ve
1002 f ddi - def aul t act / unsup
1003 t oken- r i ng- def aul t act / unsup
1004 f ddi net - def aul t act / unsup
1005 t r net - def aul t act / unsup

Step 3
If you issue the show spanning-tree command on one of the switches,
you see 11 spanning tree instances running.
DLS1#show spanni ng- t r ee

VLAN0001
Spanni ng t r ee enabl ed pr ot ocol i eee
Root I D Pr i or i t y 32769
Addr ess 000a. b8a9. d680
Cost 19
3 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32769 ( pr i or i t y 32768 sys- i d- ext 1)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec
Agi ng Ti me 300

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 19 128. 9 P2p
Fa0/ 8 Desg FWD 19 128. 10 P2p
Fa0/ 9 Desg FWD 19 128. 11 P2p
Fa0/ 10 Desg FWD 19 128. 12 P2p
Fa0/ 11 Root FWD 19 128. 13 P2p
Fa0/ 12 Al t n BLK 19 128. 14 P2p


VLAN0010
Spanni ng t r ee enabl ed pr ot ocol i eee
Root I D Pr i or i t y 32778
Addr ess 000a. b8a9. d680
Cost 19
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32778 ( pr i or i t y 32768 sys- i d- ext 10)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec
Agi ng Ti me 300

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 19 128. 9 P2p
Fa0/ 8 Desg FWD 19 128. 10 P2p
Fa0/ 9 Desg FWD 19 128. 11 P2p
Fa0/ 10 Desg FWD 19 128. 12 P2p
Fa0/ 11 Root FWD 19 128. 13 P2p
Fa0/ 12 Al t n BLK 19 128. 14 P2p


VLAN0020
Spanni ng t r ee enabl ed pr ot ocol i eee
Root I D Pr i or i t y 32788
Addr ess 000a. b8a9. d680
Cost 19
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32788 ( pr i or i t y 32768 sys- i d- ext 20)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec
Agi ng Ti me 300

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 19 128. 9 P2p
Fa0/ 8 Desg FWD 19 128. 10 P2p
Fa0/ 9 Desg FWD 19 128. 11 P2p
Fa0/ 10 Desg FWD 19 128. 12 P2p
Fa0/ 11 Root FWD 19 128. 13 P2p
Fa0/ 12 Al t n BLK 19 128. 14 P2p

4 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

<out put omi t t ed>

VLAN0090
Spanni ng t r ee enabl ed pr ot ocol i eee
Root I D Pr i or i t y 32858
Addr ess 000a. b8a9. d680
Cost 19
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32858 ( pr i or i t y 32768 sys- i d- ext 90)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec
Agi ng Ti me 300

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 19 128. 9 P2p
Fa0/ 8 Desg FWD 19 128. 10 P2p
Fa0/ 9 Desg FWD 19 128. 11 P2p
Fa0/ 10 Desg FWD 19 128. 12 P2p
Fa0/ 11 Root FWD 19 128. 13 P2p
Fa0/ 12 Al t n BLK 19 128. 14 P2p


VLAN0100
Spanni ng t r ee enabl ed pr ot ocol i eee
Root I D Pr i or i t y 32868
Addr ess 000a. b8a9. d680
Cost 19
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32868 ( pr i or i t y 32768 sys- i d- ext 100)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec
Agi ng Ti me 300

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 19 128. 9 P2p
Fa0/ 8 Desg FWD 19 128. 10 P2p
Fa0/ 9 Desg FWD 19 128. 11 P2p
Fa0/ 10 Desg FWD 19 128. 12 P2p
Fa0/ 11 Root FWD 19 128. 13 P2p
Fa0/ 12 Al t n BLK 19 128. 14 P2p

Spanning tree is running a separate spanning tree instance for each VLAN
we created, plus VLAN 1. This method assumes that each VLAN could be
running on a differently shaped topology. However, in many networks,
multiple VLANs follow the same physical topology, so multiple spanning-
tree calculations for the same topologies can get redundant. MST (multiple
spanning tree) lets you configure different spanning tree instances. Each
instance can hold a group of VLANs and gets its own spanning tree
calculation.
MST is convenient in that it is backward compatible with PVST. Two
switches only run MST with each other if they are in the same MST region.
An MST region is defined by switches having identical region names,
5 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

revision numbers, and VLAN-to-instance assignments. If they differ by any
single attribute, they are considered different MST regions and fall back to
PVST.
Step 4
To configure MST, first use the global configuration command spanning-
tree mode mst on all four switches.
DLS1( conf i g) #spanning-tree mode mst

By default, all VLANs are assigned to instance 0, but can be moved
around to different instances when MST is configured. Issue the show
spanning-tree command and observe that there is only one spanning tree
(instance 0) coming up. Also notice that the mode is listed as MSTP.
DLS1#show spanning-tree

MST00
Spanni ng t r ee enabl ed pr ot ocol mst p
Root I D Pr i or i t y 32768
Addr ess 000a. b8a9. d680
Cost 0
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32768 ( pr i or i t y 32768 sys- i d- ext 0)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 200000 128. 9 P2p
Fa0/ 8 Desg BLK 200000 128. 10 P2p
Fa0/ 9 Desg FWD 200000 128. 11 P2p
Fa0/ 10 Desg FWD 200000 128. 12 P2p
Fa0/ 11 Root FWD 200000 128. 13 P2p
Fa0/ 12 Al t n BLK 200000 128. 14 P2p

If you use the show spanning-tree mst configuration command, you
can see a switchs current MST configuration. Because you have not
configured any MST region settings, the switch shows the default settings.
DLS1#show spanning-tree mst configuration
Name [ ]
Revi si on 0
I nst ance Vl ans mapped
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 1- 4094
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Step 5
Now that MST has been enabled, we can configure the MST region
settings to group VLANs. We use the region name CISCO and a revision
number of 1. We put VLANs 20 through 50 into instance 1, and 80 and
100 into instance 2. The rest of the VLANs remain in instance 0, the
6 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

default. To begin modifying the MST configuration, type the global
configuration command spanning-tree mst configuration. Configuring
MST is different from other switch configurations, because changes are
not applied until you are done, and you can abort changes if you want to.
Note: You must apply identical configurations on each switch for MST to
work properly.
DLS1#conf i gur e t er mi nal
Ent er conf i gur at i on commands, one per l i ne. End wi t h CNTL/ Z.
DLS1( conf i g) #spanning-tree mst configuration
DLS1( conf i g- mst ) #

When you are in MST configuration mode, you can view the current
configuration using the show current command. You do not need to leave
configuration mode to execute this command. Notice that the output is
identical to show spanning-tree mst configuration.
DLS1( conf i g- mst ) #show current
Cur r ent MST conf i gur at i on
Name [ ]
Revi si on 0
I nst ance Vl ans mapped
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 1- 4094
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Change the region name by typing name name. Change the revision
number by typing revision number.
DLS1( conf i g- mst ) #name CI SCO
DLS1( conf i g- mst ) #r evi si on 1

The last configuration change you have to make is putting VLANs into
instances. Use the command instance number vlan vlan_range. The
instance number can be between 0 and 15. Remember that 0 is the
default instance number.
DLS1( conf i g- mst ) # i nst ance 1 vl an 20- 50
DLS1( conf i g- mst ) # i nst ance 2 vl an 80, 100

You can verify the changes you are about to make with the show
pending command. Remember that the changes that you just entered are
not committed until you type exit. If you do not like the changes you made,
you can leave the prompt without committing them by typing abort. In the
output below, notice the difference between show current and show
pending.
DLS1( conf i g- mst ) #show current
Cur r ent MST conf i gur at i on
Name [ ]
Revi si on 0
I nst ance Vl ans mapped
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 1- 4094
7 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DLS1( conf i g- mst ) #show pending
Pendi ng MST conf i gur at i on
Name [ CI SCO]
Revi si on 1
I nst ance Vl ans mapped
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 1- 19, 51- 79, 81- 99, 101- 4094
1 20- 50
2 80, 100
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DLS1( conf i g- mst ) #exi t

If you enter the show spanning-tree mst configuration command, you
can see that the current configuration reflects the changes you just
committed. Remember to perform the same configuration on all four
switches.
DLS1#show span mst configuration
Name [ CI SCO]
Revi si on 1
I nst ance Vl ans mapped
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 1- 19, 51- 79, 81- 99, 101- 4094
1 20- 50
2 80, 100
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Why do the switches wait until you are finished making changes to MST to
commit them, rather that changing MST as you enter commands (like
most switch commands)?


Verify that you have separate instances of spanning tree running for each
MST instance:
DLS1#show spanning-tree

MST00
Spanni ng t r ee enabl ed pr ot ocol mst p
Root I D Pr i or i t y 32768
Addr ess 000a. b8a9. d680
Cost 0
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32768 ( pr i or i t y 32768 sys- i d- ext 0)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 200000 128. 9 P2p
Fa0/ 8 Desg FWD 200000 128. 10 P2p
Fa0/ 9 Desg FWD 200000 128. 11 P2p
Fa0/ 10 Desg FWD 200000 128. 12 P2p
8 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

Fa0/ 11 Root FWD 200000 128. 13 P2p
Fa0/ 12 Al t n BLK 200000 128. 14 P2p


MST01
Spanni ng t r ee enabl ed pr ot ocol mst p
Root I D Pr i or i t y 32769
Addr ess 000a. b8a9. d680
Cost 200000
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32769 ( pr i or i t y 32768 sys- i d- ext 1)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 200000 128. 9 P2p
Fa0/ 8 Desg FWD 200000 128. 10 P2p
Fa0/ 9 Desg FWD 200000 128. 11 P2p
Fa0/ 10 Desg FWD 200000 128. 12 P2p
Fa0/ 11 Root FWD 200000 128. 13 P2p
Fa0/ 12 Al t n BLK 200000 128. 14 P2p


MST02
Spanni ng t r ee enabl ed pr ot ocol mst p
Root I D Pr i or i t y 32770
Addr ess 000a. b8a9. d680
Cost 200000
Por t 13 ( Fast Et her net 0/ 11)
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

Br i dge I D Pr i or i t y 32770 ( pr i or i t y 32768 sys- i d- ext 2)
Addr ess 000a. b8a9. d780
Hel l o Ti me 2 sec Max Age 20 sec For war d Del ay 15 sec

I nt er f ace Rol e St s Cost Pr i o. Nbr Type
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Fa0/ 7 Desg FWD 200000 128. 9 P2p
Fa0/ 8 Desg FWD 200000 128. 10 P2p
Fa0/ 9 Desg FWD 200000 128. 11 P2p
Fa0/ 10 Desg FWD 200000 128. 12 P2p
Fa0/ 11 Root FWD 200000 128. 13 P2p
Fa0/ 12 Al t n BLK 200000 128. 14 P2p

Challenge
You can modify per-instance MST spanning tree attributes the same way
you can modify per-VLAN attributes. Make DLS1 the root of instance 1
and DLS2 the root of instance 2.
HINT: Use a question mark on the global configuration command
spanning-tree mst ?.



9 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc




END OF LAB FINAL CONFIGS:

DLS1#show r unni ng- conf i g
!
host name DLS1
!
!
vt p domai n CI SCO
vt p mode t r anspar ent
!
!
!
!
!
spanni ng- t r ee mst conf i gur at i on
name CI SCO
r evi si on 1
i nst ance 1 vl an 20- 50
i nst ance 2 vl an 80, 100
!
spanni ng- t r ee mst 1 pr i or i t y 24576
!
!
vl an 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
!
!
i nt er f ace Fast Et her net 0/ 7
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 8
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 9
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 10
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 11
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 12
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
!
end

DLS2#show r unni ng- conf i g
!
host name DLS2
10 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

!
!
vt p domai n CI SCO
vt p mode t r anspar ent
!
!
spanni ng- t r ee mode mst
!
spanni ng- t r ee mst conf i gur at i on
name CI SCO
r evi si on 1
i nst ance 1 vl an 20- 50
i nst ance 2 vl an 80, 100
!
spanni ng- t r ee mst 2 pr i or i t y 24576
!
!
vl an 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
!
!
!
i nt er f ace Fast Et her net 0/ 7
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 8
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 9
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 10
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 11
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 12
swi t chpor t t r unk encapsul at i on dot 1q
swi t chpor t mode t r unk
!
!
end

ALS1#show r unni ng- conf i g
!
host name ALS1
!
!
vt p domai n CI SCO
vt p mode t r anspar ent
!
!
spanni ng- t r ee mode mst
!
spanni ng- t r ee mst conf i gur at i on
name CI SCO
r evi si on 1
i nst ance 1 vl an 20- 50
11 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

i nst ance 2 vl an 80, 100
!
!
vl an 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
!
!
i nt er f ace Fast Et her net 0/ 7
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 8
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 9
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 10
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 11
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 12
swi t chpor t mode t r unk
!
!
end

ALS2#show r unni ng- conf i g
!
host name ALS2
!
!
vt p domai n CI SCO
vt p mode t r anspar ent
!
!
spanni ng- t r ee mode mst
!
spanni ng- t r ee mst conf i gur at i on
name CI SCO
r evi si on 1
i nst ance 1 vl an 20- 50
i nst ance 2 vl an 80, 100
!
!
vl an 10, 20, 30, 40, 50, 60, 70, 80, 90, 100
!
!
i nt er f ace Fast Et her net 0/ 7
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 8
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 9
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 10
swi t chpor t mode t r unk
!
i nt er f ace Fast Et her net 0/ 11
swi t chpor t mode t r unk
!
12 - 12 CCNP: Building Multilayer Switched Networks v5.0 - Lab 3-4 Copyright 2006, Cisco Systems, Inc

i nt er f ace Fast Et her net 0/ 12
swi t chpor t mode t r unk
!
!
end