1.

General Description
A: WIRING DIAGRAM
The wiring diagram of each system is illustrated so
that you can understand the path through which
the electric current flows from the battery.
Sketches and codes are used in the diagrams.
They should read as follows:
Each connector and its terminal position are
indicated by a sketch of the connector in a discon-
nected state which is viewed from the front.
G6M0193
The number of poles or pins, presence of a lock, and pin number of each terminal are indicated in the
sketch of each connector. In the sketch, the highest pole number refers to the number of poles which the
connector has. For example, the sketch of the connector shown in figure indicates the connector has 9
poles.
Connector used in vehicle
Connector shown in wiring diagram
Sketch Symbol Number of poles
G6M0194
G6M0196
G6M0198
Numbered in order from upper
right to lower left.
G6M0195
G6M0197
Numbered in order from upper
left to lower right.
2
6-3 [D1A0] WIRING DIAGRAM
1. General Description
When one set of connectors is viewed from the
front side, the pole numbers of one connector are
symmetrical to those of the other. When these two
connectors are connected as a unit, the poles
which have the same number are joined.
G6M0199
Electrical wiring harness:
The connectors are numbered along with the num-
ber of poles, external colors, and mating connec-
tions in the accompanying list.
The sketch of each connector in the wiring dia-
gram usually shows the (A) side of the connector.
The relationship between the wire color, terminal
number and connector is described in figure.
NOTE:
A wire which runs in one direction from a connec-
tor terminal sometimes may have a different color
from that which runs in the other direction from that
terminal.
H6M0509A
In wiring diagram, connectors which have no ter-
minal number refer to one-pole types. Sketches of
these connectors are omitted intentionally.
G6M0216
The following color codes are used to indicate
the colors of the wires used.
Color code Color
L Blue
B Black
Y Yellow
G Green
R Red
W White
Br Brown
Lg Light green
Gr Gray
P Pink
Or Orange
Lb Light Blue
V Violet
SA Sealed (Inner)
SB Sealed (Outer)
G6M0201
3
[D1A0] 6-3 WIRING DIAGRAM
1. General Description
The wire color code, which consists of two let-
ters (or three letters including Br or Lg), indicates
the standard color (base color of the wire covering)
by its first letter and the stripe marking by its sec-
ond letter.
G6M0202
The table lists the nominal sectional areas and
allowable currents of the wires.
CAUTION:
When replacing or repairing a wire, be sure
to use the same size and type of the wire which
was originally used.
NOTE:
The allowable current in the table indicates the
tolerable amperage of each wire at an ambient
temperature of 40C (104F).
The allowable current changes with ambient
temperature. Also, it changes if a bundle of more
than two wires is used.
Nominal sec-
tional area
mm
2
No. of
strands/
strand diam-
eter
Outside
diameter of
finished wir-
ing
mm
Allowable
current
Amps/40C
0.3 7/0.26 1.8 7
0.5 7/0.32 2.2 (or 2.0) 12
0.75 30/0.18 2.6 (or 2.4) 16
0.85 11/0.32 2.4 (or 2.2) 16
1.25 16/0.32 2.7 (or 2.5) 21
2 26/0.32 3.1 (or 2.9) 28
3 41/0.32 3.8 (or 3.6) 38
5 65/0.32 4.6 (or 4.4) 51
8 50/0.45 5.5 67
Each unit is directly grounded to the body or
indirectly grounds through a harness ground termi-
nal. Different symbols are used in the wiring dia-
gram to identify the two grounding systems.
G6M0203
The ground points shown in the wiring diagram
refer to the following:
NOTE:
All wiring harnesses are provided with a ground
point which should be securely connected.
H6M0787A
4
6-3 [D1A0] WIRING DIAGRAM
1. General Description
Relays are classified as normally-open or normally-closed. The normally-closed relay has one or more
contacts.
The wiring diagram shows the relay mode when the energizing circuit is OFF.
B6M0748
5
[D1A0] 6-3 WIRING DIAGRAM
1. General Description
Each connector number shown in the wiring dia-
gram corresponds to that in the wiring harness.
The location of each connector in the actual
vehicle is determined by reading the first character
of the connector (for example, a F for F8, i for
i16, etc.) and the type of wiring harness.
The first character of each connector number
refers to the area or system of the vehicle.
Symbol Wiring harness and cord
F Front wiring harness
B Bulkhead wiring harness
E
Engine wiring harness,
Oxygen sensor cord
T Transmission cord
D
Door cord LH & RH,
Rear door cord LH & RH
i Instrument panel wiring harness
R
Rear wiring harness,
Rear defogger cord (Ground)
Fuel tank cord,
Roof cord,
Rear gate cord,
Rear gate lock adapter cord
G6M0205
2. Basic Diagnostics Procedure
A: BASIC PROCEDURE
1. GENERAL
The most important purpose of diagnostics is to
determine which part is malfunctioning quickly, to
save time and labor.
2. IDENTIFICATION OF TROUBLE
SYMPTOM
Determine what the problem is based on the symp-
tom.
3. PROBABLE CAUSE OF TROUBLE
Look at the wiring diagram and check the systems
circuit. Then check the switch, relay, fuse, ground,
etc.
4. LOCATION AND REPAIR OF TROUBLE
1) Using the diagnostics narrow down the causes.
2) If necessary, use a voltmeter, ohmmeter, etc.
3) Before replacing certain component parts
(switch, relay, etc.), check the power supply,
ground, for open wiring harness, poor connectors,
etc. If no problems are encountered, check the
component parts.
5. CONFIRMATION OF SYSTEM
OPERATION
After repairing, ensure that the system operates
properly.
B: INSPECTION
1. VOLTAGE MEASUREMENT
1) Using a voltmeter, connect the negative lead to
a good ground point or negative battery terminal
and the positive lead to the connector or compo-
nent terminal.
2) Contact the positive probe of the voltmeter on
connector (A).
The voltmeter will indicate a voltage.
3) Shift the positive probe to connector (B). The
voltmeter will indicate no voltage.
H6M0510A
6
6-3 [D2A1] WIRING DIAGRAM
2. Basic Diagnostics Procedure
4) With test set-up held as it is, turn switch ON.
The voltmeter will indicate a voltage and, at the
same time, the light will come on.
5) The circuit is in good order. If a problem such
as a lamp failing to light occurs, use the proce-
dures outlined above to track down the malfunc-
tion.
2. CIRCUIT CONTINUITY CHECKS
1) Disconnect the battery terminal or connector so
there is no voltage between the check points.
Contact the two leads of an ohmmeter to each of
the check points.
If the circuit has diodes, reverse the two leads and
check again.
2) Use an ohmmeter to check for diode continuity.
When contacting the negative lead to the diode
positive side and the positive lead to the negative
side, there should be continuity.
When contacting the two leads in reverse, there
should be no continuity.
G6M0207
3) Symbol kk indicates that continuity exists
between two points or terminals. For example,
when a switch position is 3, continuity exists
among terminals 1, 3 and 6, as shown in table
below.
B6M0749
3. HOW TO DETERMINE AN OPEN
CIRCUIT
1) Voltmeter Method:
An open circuit is determined by measuring the
voltage between respective connectors and
ground using a voltmeter, starting with the connec-
tor closest to the power supply. The power supply
must be turned ON so that current flows in the cir-
cuit. If voltage is not present between a particular
connector and ground, the circuit between that
connector and the previous connector is open.
G6M0208
2) Ohmmeter method:
Disconnect all connectors affected, and check con-
tinuity in the wiring between adjacent connectors.
When the ohmmeter indicates infinite, the wiring
is open.
G6M0209
7
[D2B3] 6-3 WIRING DIAGRAM
2. Basic Diagnostics Procedure
4. HOW TO DETERMINE A
SHORTCIRCUIT
1) Test lamp method:
Connect a test lamp (rated at approximately 3
watts) in place of the blown fuse and allow current
to flow through the circuit. Disconnect one connec-
tor at a time from the circuit, starting with the one
located farthest from the power supply. If the test
lamp goes out when a connector is disconnected,
the wiring between that connection and the next
connector (farther from the power supply) is
shorted.
G6M0210
2) Ohmmeter method:
Disconnect all affected connectors, and check con-
tinuity between each connector and ground. When
ohmmeter indicates continuity between a particular
connector and ground, that connector is shorted.
G6M0211
3. Working Precautions
A: PRECAUTIONS WHEN WORKING
WITH THE PARTS MOUNTED ON
THE VEHICLE
1) When working under a vehicle which is jacked-
up, always be sure to use safety stands.
2) The parking brake must always be applied dur-
ing working. Also, in automatic transmission
vehicles, keep the select lever set to the P (Park-
ing) range.
3) Be sure the workshop is properly ventilated
when running the engine. Further, be careful not to
touch the belt or fan while the engine is operating.
4) Be careful not to touch hot metal parts, espe-
cially the radiator and exhaust system immediately
after the engine has been shut off.
B: PRECAUTIONS IN TROUBLE
DIAGNOSIS AND REPAIR OF
ELECTRIC PARTS
1) The battery cable must be disconnected from
the batterys () terminal, and the ignition switch
must be set to the OFF position, unless otherwise
required by the diagnostics.
2) Securely fasten the wiring harness with clamps
and slips so that the harness does not interfere
with the body end parts or edges and bolts or
screws.
3) When installing parts, be careful not to catch
them on the wiring harness.
4) When disconnecting a connector, do not pull
the wires, but pull while holding the connector
body.
G6M0212
8
6-3 [D2B4] WIRING DIAGRAM
3. Working Precautions
5) Some connectors are provided with a lock. One
type of such a connector is disconnected by push-
ing the lock, and the other, by moving the lock up.
In either type the lock shape must be identified
before attempting to disconnect the connector.
To connect, insert the connector until it snaps and
confirm that it is tightly connected.
G6M0213
6) When checking continuity between connector
terminals, or measuring voltage across the termi-
nal and ground, always contact tester probe(s) on
terminals from the wiring connection side. If the
probe is too thick to gain access to the terminal,
use mini test leads.
To check water-proof connectors (which are not
accessible from the wiring side), contact test
probes on the terminal side being careful not to
bend or damage the terminals.
G6M0214
7) Sensors, relays, electrical unit, etc., are sensi-
tive to strong impacts.
Handle them with care so that they are not dropped
or mishandled.
9
[D3B0] 6-3 WIRING DIAGRAM
3. Working Precautions
4. How to Use Wiring Diagram
H6M0796A
A: RELAY
A symbol used to indicate a relay.
B: CONNECTOR-1
The sketch of the connector indicates the one-pole
types.
C: WIRING CONNECTION
Some wiring diagrams are indicated in foldouts for
convenience. Wiring destinations are indicated
where necessary by corresponding symbols (as
when two pages are needed for clear indication).
D: FUSE No. & RATING
The FUSE No. & RATING corresponds with that
used in the fuse box (main fuse box, fuse and joint
box).
E: CONNECTOR-2
Each connector is indicated by a symbol.
Each terminal number is indicated in the corre-
sponding wiring diagram in an abbreviated form.
For example, terminal number C2 refers to No.
2 terminal of connector (C: F41) shown in the con-
nector sketch.
10
6-3 [D400] WIRING DIAGRAM
4. How to Use Wiring Diagram
F: CONNECTOR SKETCH
Each connector sketch clearly identifies the
shape and color of a connector as well as terminal
locations. Non-colored connectors are indicated in
natural color.
When more than two types of connector number
are indicated in a connector sketch, it means that
the same type connectors are used.
G: GROUND
Each grounding point can be located easily by
referring to the corresponding wiring harness.
H: DIODE
A symbol is used to indicate a diode.
I: WIRE TRACING ON EXTENDED
WIRING DIAGRAMS
For a wiring diagram extending over at least two
pages, a symbol (consisting of the same charac-
ters with arrows), facilitates wire tracing from one
page to the next.
A A, B B
J: SYMBOLS OF WIRE
CONNECTION AND CROSSING
B6M0750A
K: POWER SUPPLY ROUTING
A symbol is used to indicate the power supply in
each wiring diagram.
MB-5, MB-6, etc., which are used as power-
supply symbols throughout the text, correspond
with those shown in the POWER SUPPLY ROUT-
ING in the wiring diagram.
Accordingly, using the POWER SUPPLY ROUT-
ING and wiring diagrams permits service person-
nel to understand the entire electrical arrangement
of a system.
L: SYMBOLS AND ABBREVIATIONS
A number of symbols and abbreviations are used
in each wiring diagram to easily identify parts or
circuits.
M: ABBREVIATION LIST
Abbr. Full name
ABS Antilock Brake System
ACC Accessory
A/C Air Conditioning
AD Auto Down
AT Automatic Transmission
AU Auto Up
+B Battery
DN Down
E Ground
F/B Fuse & Joint Box
FL1.5 Fusible link 1.5 mm
2
IG Ignition
Illumi. Illumination
LH Left Hand
Lo Low
M Motor
M/B Main Fuse Box
MG Magnet
Mi Middle
OP Optional Parts
PASS Passing
RH Right Hand
SBF Slow Blow Fuse
ST Starter
SW Switch
UP Up
WASH Washer
11
[D4M0] 6-3 WIRING DIAGRAM
4. How to Use Wiring Diagram
5. Wiring Diagram
A: POWER SUPPLY ROUTING
GU01-05A
12
6-3 [D5A0] WIRING DIAGRAM
5. Wiring Diagram
GU01-05B
13
[D5A0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
No. Load
MB-1 Power window and sunroof circuit breaker
MB-2
Door lock timer
Keyless entry control module
MB-3
Data link connector
Engine control module
Fuel pump relay
Main relay
MB-4
Daytime running light control module
Diode (Daytime running light)
Lighting switch
MB-5
Cruise control sub switch
Horn switch
MB-6 Transmission control module
MB-7
AT shift lock control module
Hazard switch
Key warning switch
MB-8 Horn
MB-9 Headlight LH
MB-10
Combination meter
Front fog light relay
Front fog light switch
Headlight RH
MB-11 A/C relay holder
SBF-7 ABS control module
ALT
Combination meter
Daytime running light control module
ST
Engine control module (AT)
Inhibitor switch (AT)
Starter interlock relay (MT)
FB-1 Main fan relay
FB-2 Parking switch
FB-3 Blower motor relay
FB-4 Front fog light relay
FB-5 ABS control module
FB-6 Stop light switch
FB-7 Rear accessory power supply relay
FB-8 Airbag control module
FB-9 Airbag control module
FB-10
Engine control module
Fuel pump relay
Ignition coil
Transmission control module
FB-11
Blower motor relay
Mode control panel
Rear defogger switch
FB-12
A/C relay
Sub fan relay
Thermal protector
No. Load
FB-13
Back-up light switch (MT)
Check connector
Combination meter
Daytime running light control module
Daytime running light hi-beam relay
Daytime running light relay
Hazard switch
Inhibitor switch (AT)
Key warning module
Keyless entry control module
Power window and sunroof relay
Vehicle speed sensor (MT)
FB-14
Engine control module
Rear defogger switch
FB-15
Rear defogger
Rear defogger switch
FB-16 Lighting switch
FB-17 Parking switch
FB-18
Keyless entry control module
Parking switch
FB-19
Clock
Illumination control module
Illumination light
Keyless entry control module
FB-20
AT shift lock control module
Front accessory power supply
Remote control rearview mirror switch
Rear accessory power supply relay
FB-21 Radio
FB-22
Front washer motor
Front wiper motor
Front wiper & washer switch
Rear washer motor
Rear wiper motor
Rear wiper relay
FB-23
Combination meter
Radio
Room light
Spot light
Trunk room light
FB-24
License plate light LH
License plate light RH
Tail light LH
Tail light RH
FB-25
Front clearance light LH
Front clearance light RH
FB-26
Combination meter
Hazard switch
Rear turn signal light LH
Turn signal switch
FB-27
Front turn signal light LH
Side turn signal light LH
FB-28
Combination meter
Hazard switch
Rear turn signal light RH
Turn signal switch
FB-29
Front turn signal light RH
Side turn signal light RH
14
6-3 [D5A0] WIRING DIAGRAM
5. Wiring Diagram
No. Load
FB-30
ABS control module
AT shift lock control module
Cruise control main switch
Cruise control module
15
[D5A0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
B: GROUND DISTRIBUTION
GU04-07A
16
6-3 [D5B0] WIRING DIAGRAM
5. Wiring Diagram
GU04-07B
17
[D5B0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
GU04-07C
18
6-3 [D5B0] WIRING DIAGRAM
5. Wiring Diagram
C: AIRBAG SYSTEM
GU86-07
19
[D5C0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
D: AIR CONDITIONING SYSTEM
GU45-07A
20
6-3 [D5D0] WIRING DIAGRAM
5. Wiring Diagram
GU45-07B
21
[D5D0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
E: ANTI-LOCK BRAKE SYSTEM
GU82-07A
22
6-3 [D5E0] WIRING DIAGRAM
5. Wiring Diagram
GU82-07B
23
[D5E0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
F: A/T CONTROL SYSTEM
GU41-09A
24
6-3 [D5F0] WIRING DIAGRAM
5. Wiring Diagram
GU41-09B
25
[D5F0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
G: A/T SHIFT LOCK SYSTEM
GU42-07
26
6-3 [D5G0] WIRING DIAGRAM
5. Wiring Diagram
H: AUDIO SYSTEM
GU76-06
27
[D5H0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
I: CHARGING SYSTEM
GU02-06
28
6-3 [D5I0] WIRING DIAGRAM
5. Wiring Diagram
J: COMBINATION METER
GU65-06
29
[D5J0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
K: CRUISE CONTROL SYSTEM
GU71-08
30
6-3 [D5K0] WIRING DIAGRAM
5. Wiring Diagram
L: DOOR LOCK SYSTEM
GU73-06
31
[D5L0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
M: ENGINE ELECTRICAL SYSTEM
1. 2200 cc ENGINE MODEL
GU10-16A
32
6-3 [D5M1] WIRING DIAGRAM
5. Wiring Diagram
GU10-16B
33
[D5M1] 6-3 WIRING DIAGRAM
5. Wiring Diagram
GU10-16C
34
6-3 [D5M1] WIRING DIAGRAM
5. Wiring Diagram
GU10-16D
35
[D5M1] 6-3 WIRING DIAGRAM
5. Wiring Diagram
2. 2500 cc ENGINE MODEL
GU10-17A
36
6-3 [D5M2] WIRING DIAGRAM
5. Wiring Diagram
GU10-17B
37
[D5M2] 6-3 WIRING DIAGRAM
5. Wiring Diagram
GU10-17C
38
6-3 [D5M2] WIRING DIAGRAM
5. Wiring Diagram
GU10-17D
39
[D5M2] 6-3 WIRING DIAGRAM
5. Wiring Diagram
N: FUEL GAUGE SYSTEM
GU61-08
40
6-3 [D5N0] WIRING DIAGRAM
5. Wiring Diagram
O: HORN AND FRONT ACCESSORY POWER SUPPLY SYSTEM
GU74-04
41
[D5O0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
P: KEYLESS ENTRY SYSTEM
GU77-01
42
6-3 [D5P0] WIRING DIAGRAM
5. Wiring Diagram
Q: LIGHTING SYSTEM (BACK-UP LIGHT)
GU29-06
43
[D5Q0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
R: LIGHTING SYSTEM (CLEARANCE LIGHT AND ILLUMINATION LIGHT)
GU21-07A
44
6-3 [D5R0] WIRING DIAGRAM
5. Wiring Diagram
GU21-07B
45
[D5R0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
S: LIGHTING SYSTEM (FRONT FOG LIGHT)
1. WITHOUT DAYTIME RUNNING LIGHT MODEL
GU22-05
46
6-3 [D5S1] WIRING DIAGRAM
5. Wiring Diagram
2. WITH DAYTIME RUNNING LIGHT MODEL
GC22-01
47
[D5S2] 6-3 WIRING DIAGRAM
5. Wiring Diagram
T: LIGHTING SYSTEM (HEADLIGHT)
1. WITHOUT DAYTIME RUNNING LIGHT MODEL
GU20-07
48
6-3 [D5T1] WIRING DIAGRAM
5. Wiring Diagram
2. WITH DAYTIME RUNNING LIGHT MODEL
GC20-08
49
[D5T2] 6-3 WIRING DIAGRAM
5. Wiring Diagram
U: LIGHTING SYSTEM (IN COMPARTMENT)
GU24-06
50
6-3 [D5U0] WIRING DIAGRAM
5. Wiring Diagram
V: LIGHTING SYSTEM (STOP LIGHT)
GU25-05
51
[D5V0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
W: LIGHTING SYSTEM (TURN SIGNAL LIGHT AND HAZARD LIGHT)
GU26-05
52
6-3 [D5W0] WIRING DIAGRAM
5. Wiring Diagram
X: MULTIPLE POWER SOCKET SYSTEM (OPTION)
GU82-01
53
[D5X0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
Y: OIL PRESSURE AND TEMPERATURE GAUGE SYSTEM
GU66-07
54
6-3 [D5Y0] WIRING DIAGRAM
5. Wiring Diagram
Z: PARKING BRAKE AND BRAKE FLUID LEVEL WARNING SYSTEM
GU60-06
55
[D5Z0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
AA: POWER WINDOW SYSTEM
1. SEDAN AND WAGON MODEL
GU70-08A
56
6-3 [D5AA1] WIRING DIAGRAM
5. Wiring Diagram
GU70-08B
57
[D5AA1] 6-3 WIRING DIAGRAM
5. Wiring Diagram
2. COUPE MODEL
GU70-07
58
6-3 [D5AA2] WIRING DIAGRAM
5. Wiring Diagram
AB: RADIATOR FAN SYSTEM
GU14-11
59
[D5AB0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
AC: REAR ACCESSORY POWER SUPPLY SYSTEM
GU90-03
60
6-3 [D5AC0] WIRING DIAGRAM
5. Wiring Diagram
AD: REAR WINDOW DEFOGGER SYSTEM
GU52-07
61
[D5AD0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
AE: REMOTE CONTROLLED REARVIEW MIRROR SYSTEM
GU79-05
62
6-3 [D5AE0] WIRING DIAGRAM
5. Wiring Diagram
AF: SEAT BELT WARNING AND KEY WARNING SYSTEM
GU87-06
63
[D5AF0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
AG: STARTER SYSTEM
GU03-05
64
6-3 [D5AG0] WIRING DIAGRAM
5. Wiring Diagram
AH: SUNROOF SYSTEM
GU75-03
65
[D5AH0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
AI: WIPER AND WASHER SYSTEM (FRONT)
GU50-03
66
6-3 [D5AI0] WIRING DIAGRAM
5. Wiring Diagram
AJ: WIPER AND WASHER SYSTEM (REAR)
GU51-04
67
[D5AJ0] 6-3 WIRING DIAGRAM
5. Wiring Diagram
MEMO:
68
6-3 [D5AJ0] WIRING DIAGRAM
5. Wiring Diagram
6. Electrical Wiring Harness and Ground Point
A: OVERALL LOCATION
H6M0781A
(1) Front wiring harness
(2) Engine wiring harness
(3) Bulkhead wiring harness
(4) Instrument panel wiring harness
(5) Front door cord RH
(6) Rear door adapter cord RH
(7) Rear door cord RH
(8) Rear wiring harness
(9) Rear defogger cord (Ground)
(10) Fuel tank cord
(11) Rear door cord LH
(12) Rear door adapter cord LH
(13) Front door cord LH
(14) Roof cord
(15) Transmission cord
(16) Rear gate cord
(17) Rear gate lock adapter cord
(18) Oxygen sensor cord
(19) Combination switch cord
(20) Trunk lid cord
69
[D6A0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
B: FRONT WIRING HARNESS
List of Items
Connector Connecting to
No. Pole Color Area No. Name
F2 16 Blue B-4 B100 Bulkhead wiring harness (ABS)
F3 2 # B-1 Front turn signal light RH
F5 1 2 # B-1 Horn
F6 2 Black B-1 Front fog light RH
F7 3 # B-1 Headlight RH
F16 2 Black B-1 Sub fan motor
F17 2 Black B-2 Radiator main fan motor
F19 2 # C-3 Front turn signal light LH
F21 2 Black C-2 Front fog light LH
F23 3 # B-2 Headlight LH
F24 3 Gray B-2 A/C compressor
F25 1 # B-2
Generator
F26 3 Green B-2
F27 4 # B-3 A/C fuse (Relay holder)
F28 4 # B-3 A/C sub fan relay (Relay holder)
F31 4 # B-3 A/C relay (Relay holder)
F32 2 Green B-3 Front washer motor
F33 2 # B-3 Rear washer motor
F34 4 # B-3 SBF holder
F35 2 # B-3
M/B
F36 3 # B-3
F37 6 Black B-3
F38 1 # B-3
F39 8 Black B-3
F40 9 Brown B-4
F/B
F41 7 Gray B-4
F44 8 # B-4 B61
Bulkhead wiring harness F45 20 # B-4 B62
F46 8 # B-4 B108
F49 31 # B-2 ABS control module
F51 2 # B-2 Side turn signal light RH
F52 2 Gray B-1 Front clearance light RH
F53 2 Gray C-3 Front clearance light LH
F54 2 # B-4 Side turn signal light LH
F55 12 # B-4 R49 Rear wiring harness (ABS)
F62 6 # B-1 F63
Shield joint connector (ABS)
F63 6 # B-1 F62
F64 1 # B-2 ABS motor ground
F66 4 # B-3 Radiator main fan relay (Relay holder)
F67 2 # B-3 FWD switch (Relay holder)
F68 4 Black B-3 M/B
#: Non-colored
70
6-3 [D6B0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0782A
71
[D6B0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
C: BULKHEAD WIRING HARNESS (IN ENGINE ROOM)
List of Items
Connector Connecting to
No. Pole Color Area No. Name
B2 3 # B-2 Atmospheric pressure sensor (2500 cc engine model)
B4 4 Gray B-1 AT dropping resistor
B5 2 Gray B-2 Resistor (Daytime running light)
B6 2 # B-2 ABS front sensor RH
B7 4 # B-2 Cruise control actuator
B8 6 # B-2 Front wiper motor
B10 2 Gray B-2 A/C pressure switch
B11 20 Black B-3 T4
Transmission (AT)
B12 12 # B-3 T3
B14 1 Black B-3 Starter (Magnet)
B15 2 # B-3 ABS front sensor LH
B16 2 Gray B-3 Brake fluid level switch
B17 3 # B-2 Vehicle speed sensor (MT)
B20 10 # B-2 E1 Oxygen sensor cord
B21 20 # B-2 E2 Engine wiring harness
B22 16 # B-2 E3 Engine wiring harness
B24 2 Gray B-3 T1 Back-up light switch (MT)
B25 2 Brown B-3 T2 Neutral position switch (MT)
#: Non-colored
72
6-3 [D6C0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0783A
73
[D6C0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
D: BULKHEAD WIRING HARNESS (IN COMPARTMENT)
List of Items
Connector Connecting to
No. Pole Color Area No. Name
B30 24 # C-1 D1 Front door cord LH
B31 7 # C-1 AB1 SRS (Airbag) harness
B32 3 Black B-2 Turn & hazard module
B36 24 Blue B-2 i1
Instrument panel wiring
harness
B37 16 # B-2 i2
B40 16 # C-2 Data link connector
B41 2 # B-2
Power window circuit
breaker
B42 4 Blue B-1 Power window relay
B43 6 Black B-4 Illumination control module
B45 6 # A-4 R53 Roof cord
B46 4 Green B-1 Fuel pump relay
B47 6 Brown B-1 Main relay
B48 4 Red B-1 Front fog light relay
B50 4 # B-1 Blower relay
B51 8 Blue C-1
F/B
B52 12 Blue C-1
B53 6 # B-2 Shield joint connector (AT)
B54 24 # B-2
Transmission control mod-
ule
B55 24 Gray C-2
B57 12 # B-2
Shift lock control module
(AT)
B61 8 # B-1 F44
Front wiring harness
B62 20 # B-1 F45
B64 2 Black B-2 Stop light switch
B65 4 Black B-2
Stop & brake switch (With
cruise control)
B68 5 Black B-2 Cruise control sub switch
B69 4 # C-2
Combination switch B70 18 # C-2
B71 17 # C-2
B72 4 Blue B-2 Ignition switch
B73 2 # B-2 Key lock solenoid (AT)
B74 2 Black B-2 Key warning switch
B75 2 Green B-2 B76
Test mode connector
B76 2 Green B-2 B75
B79 14 Gray C-3 Check connector
B81 1 2 # B-2
Diagnosis terminal
(Ground)
B82 6 Black B-2 Diagnosis connector
B83 6 # C-4
Shield joint connector
(E/G)
B86 4 # B-3 Blower motor resistor
B87 2 # B-4 Blower motor
B88 4 Brown B-3 Evaporator thermoswitch
B92 6 # B-1 Door lock timer
B94 20 # C-1 Cruise control module
B95 2 # B-4
Diode (Daytime running
light)
B96 10 # B-4
Daytime running light con-
trol module
B97 10 Blue B-4 R1
Rear wiring harness B98 20 Black B-4 R2
B99 20 # B-4 R3
B100 16 Blue B-1 F2
Front wiring harness (With
ABS model)
Connector Connecting to
No. Pole Color Area No. Name
B101 24 # B-4 D11 Front door cord RH
B102 5 # B-4 Daytime running light relay
B103 4 Blue B-4
Daytime running light hi-
beam relay
B104 4 Red B-4
Rear accessory power
supply relay
B105 4 Blue B-2 Starter interlock relay (MT)
B106 2 # B-2 Clutch switch (MT)
B107 2 Blue B-2
Clutch switch (Cruise con-
trol)
B108 8 # B-1 F46 Front wiring harness
B112 2 # B-2 Diode (Front fog light)
B116 4 Black C-3
Select lever illumination
light (AT)
B117 4 # C-3
Parking position switch &
shift lock solenoid (AT)
B118 2 # C-3 CD player illumination light
B119 1 # C-3
Front accessory power
supply (Power)
B120 14 # C-3 Radio
B121 1 # B-3 Audio ground
B122 6 # C-4
Sensor ground joint con-
nector (E/G)
B125 1 Green B-4 B126
Test mode connector
B126 1 Green B-4 B125
B134
35 # B-3
Engine control module
(2200 cc engine model)
35 Black B-3
Engine control module
(2500 cc engine model)
B135
28 # B-3
Engine control module
(2200 cc engine model)
28 Black B-3
Engine control module
(2500 cc engine model)
B136
30 # B-3
Engine control module
(2200 cc engine model)
30 Black B-3
Engine control module
(2500 cc engine model)
B152 7 # B-1 F/B
B158 12 # B-1 F/B
B159 10 Gray B-1 F/B
B160 6 Gray C-1 Front fog light switch
B161 6 Brown C-1 Cruise control main switch
B162 8 # C-2 B163 Combination switch cord
B163 8 # C-2 B162 Bulkhead wiring harness
B164 18 # C-2 B165 Combination switch cord
B165 18 # C-2 B164 Bulkhead wiring harness
B166 10 # B-2 Key warning module
B167 3 # C-3
Front accessory power
supply (Ground)
B168 3 # B-3 A/C switch
B169 6 # B-3 Blower fan switch
B170 2 # B-3
Mode control panel illumi-
nation light
B175 2 # C-3 Ash tray illumi. light
B176 10 # C-2
Keyless entry control mod-
ule
#: Non-colored
74
6-3 [D6D0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0784A
75
[D6D0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
E: ENGINE WIRING HARNESS AND TRANSMISSION CORD
1. 2200 cc ENGINE MODEL
List of Items
Connector Connecting to
No. Pole Color Area No. Name
E1 10 # C-1/C-3 B20 Bulkhead wiring harness
E2 20 # A-2 B21 Bulkhead wiring harness
E3 16 # A-2 B22 Bulkhead wiring harness
E4 2 Blue A-2 Purge control solenoid valve
E5 2 Gray A-1 Injector #1
E6 2 Gray A-2 Injector #3
E7 3 Gray A-3 Idle air control solenoid valve
E8 3 # B-2 Engine coolant temperature sensor and thermometer
E10 2 # B-2 Crankshaft position sensor
E11 1 # B-2 Oil pressure switch
E12 4 Dark gray A-2 Ignition coil and ignitor
E13 3 Black A-2 Throttle position sensor
E14 2 Gray A-3 Knock sensor
E15 2 # B-3 Camshaft position sensor
E16 2 Gray B-3 Injector #2
E17 2 Gray B-4 Injector #4
E19 2 # B-2 Power steering oil pressure switch
E20 2 Black A-3 Intake air temperature sensor
E21 3 # A-3 Intake manifold pressure sensor
E24 4 # D-1/D-3 Front oxygen (A/F) sensor
E25 4 # D-2/C-4 Rear oxygen sensor
#: Non-colored
Connector Connecting to
No. Pole Color Area No. Name
T1 2 Gray D-1 B24
Bulkhead wiring harness (MT)
T2 2 Brown D-1 B25
T3 12 # D-3 B12
Bulkhead wiring harness (AT)
T4 20 Black D-3 B11
T7 12 # C-4 Inhibitor switch (AT)
#: Non-colored
76
6-3 [D6E1] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0785A
77
[D6E1] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
2. 2500 cc ENGINE MODEL
List of Items
Connector Connecting to
No. Pole Color Area No. Name
E1 10 # C-1/C-3 B20 Bulkhead wiring harness
E2 20 # A-2 B21 Bulkhead wiring harness
E3 16 # A-2 B22 Bulkhead wiring harness
E4 2 Blue A-2 Purge control solenoid valve
E5 2 Gray A-1 Injector #1
E6 2 Gray A-2 Injector #3
E7 6 # A-3 Idle air control solenoid valve
E8 3 # B-2 Engine coolant temperature sensor and thermometer
E10 2 # B-2 Crankshaft position sensor
E11 1 # B-2 Oil pressure switch
E12 4 Dark gray A-2 Ignition coil and ignitor
E13 4 # A-2 Throttle position sensor
E14 2 Gray A-3 Knock sensor
E15 2 # B-3 Camshaft position sensor
E16 2 Gray B-3 Injector #2
E17 2 Gray B-4 Injector #4
E19 2 # B-2 Power steering oil pressure switch
E21 4 # A-3 Pressure sensor and intake air temperature sensor
E24 6 # D-1/D-3 Front oxygen (A/F) sensor
E25 4 # D-2/C-4 Rear oxygen sensor
E42 2 # A-3 Air assist solenoid valve
#: Non-colored
Connector Connecting to
No. Pole Color Area No. Name
T1 2 Gray D-1 B24
Bulkhead wiring harness (MT)
T2 2 Brown D-1 B25
T3 12 # D-3 B12
Bulkhead wiring harness (AT)
T4 20 Black D-3 B11
T7 12 # C-4 Inhibitor switch (AT)
#: Non-colored
78
6-3 [D6E2] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0786A
79
[D6E2] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
F: INSTRUMENT PANEL WIRING HARNESS
List of Items
Connector Connecting to
No. Pole Color Area No. Name
i1 24 Blue B-2 B36
Bulkhead wiring harness
i2 16 # B-2 B37
i10 10 Green B-2
Combination meter i11 16 Green B-2
i12 18 Green B-2
i18 8 # B-3 Rear defogger switch
i22 8 # B-3 Hazard switch
#: Non-colored
80
6-3 [D6F0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0788A
81
[D6F0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
G: REAR WIRING HARNESS
List of Items
Connector Connecting to
No. Pole Color Area No. Name
R1 10 Blue B-2 B97
Bulkhead wiring harness R2 20 Black B-2 B98
R3 20 # B-2 B99
R4 1 Black B-3 Parking brake switch
R8 2 # B-3 Seat belt switch
R9
1 Brown B-3 Front door switch LH (Sedan and Wagon model)
2 # D-4 Front door switch LH (Coupe model)
R11 8 # B-3 D21 Rear door adapter cord LH
R12
1 Brown B-2 Front door switch RH (Sedan and Wagon model)
2 # C-3 Front door switch RH (Coupe model)
R14 8 # B-2 D27 Rear door adapter cord RH
R15 12 # B-3 R57 Fuel tank cord
R16 1 Brown A-3 Rear door switch RH
R22 1 Brown B-4 Rear door switch LH
R46 2 # B-3 R67 Fuel tank cord
R47 3 # C-1 Fuel tank pressure sensor
R49 12 # B-3 F55 Front wiring harness (With ABS model)
R52 2 # A-3 Room light
R53 6 # B-2 B45 Bulkhead wiring harness
R55 2 # A-3 Sunroof control module and sunroof motor
R56 2 # A-3 Spot light
R57 12 # B-3 R15 Rear wiring harness
R58 6 # C-1/D-1 Fuel gauge module & fuel pump assembly
R59 2 # C-2/D-2 Fuel gauge sub module
R67 2 # B-3 R46 Rear wiring harness
R68 2 Black C-2/D-1 Pressure control solenoid valve
R69 2 # C-1/D-1 Drain valve
R70 3 # B-2 ABS G sensor
R72 2 # B-3 Rear ABS sensor RH
R73 2 # B-4 Rear ABS sensor LH
R78 4 # A-3 Sunroof switch
R93 10 # B-3 Remote control rearview mirror switch
R94 2 Gray C-1 R95 Pressure control solenoid valve cord
R95 2 Gray C-1 R94 Fuel tank cord
#: Non-colored
82
6-3 [D6G0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0568A
83
[D6G0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
H: DOOR CORD
List of Items
Connector Connecting to
No. Pole Color Area No. Name
D1 13 # C-3 B30 Bulkhead wiring harness
D2 2 # C-3 Front speaker LH
D3 2 Green C-3 Front power window motor LH
D5 6 # C-3 Remote control rearview mirror LH
D7
16 # C-3 Power window main switch (Sedan and Wagon model)
12 # C-3 Power window main switch (Coupe model)
D8 4 # C-3 Front door lock actuator LH
D11 13 # B-2 B101 Bulkhead wiring harness
D12 2 # B-2 Front speaker RH
D13 2 Green B-2 Front power window motor RH
D15 6 # B-2 Remote control rearview mirror RH
D17 5 # B-2 Front power window sub switch RH
D18 4 # B-2 Front door lock actuator RH
D21 8 # C-3 R11 Rear wiring harness
D23 2 # C-4 Rear door speaker LH
D24 2 Green C-4 Rear power window motor LH
D25 5 # B-4 Rear power window sub switch LH
D26 4 # B-4 Rear door lock actuator LH
D27 8 # B-2 R14 Rear wiring harness
D29 2 # B-3 Rear door speaker RH
D30 2 Green B-3 Rear power window motor RH
D31 5 # B-2 Rear power window sub switch RH
D32 4 # B-3 Rear door lock actuator RH
D50 9 # B-2 B113 Bulkhead wiring harness
D53 3 # B-2 B124 Bulkhead wiring harness
D54 8 # C-3 D55 Rear door cord LH
D55 8 # C-3 D54 Rear door adapter cord LH
D56 8 # B-2 D57 Rear door cord RH
D57 8 # B-2 D56 Rear door adapter cord RH
D62 8 # B-2 Door lock switch RH
#: Non-colored
84
6-3 [D6H0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0538A
85
[D6H0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
I: REAR END WIRING HARNESS OF SEDAN AND COUPE
List of Items
Connector Connecting to
No. Pole Color Area No. Name
R17 1 Black B-3 Rear defogger (Power)
R18 2 Black B-3 Rear speaker RH
R19
2 # B-3 High-mount stop light (Sedan)
2 # B-3 R96 Trunk lid cord (Coupe-rear spoiler)
R20 2 Black B-3 Trunk room light
R21 2 Black B-2 Rear speaker LH
R26 7 # B-4 Rear combination light RH
R27 2 # C-3 Trunk room light switch
R28 7 # C-3 Rear combination light LH
R65 1 Black B-2 Rear defogger (Ground)
R66 2 Black B-3 High-mount stop light (Coupe-rear spoiler)
R76 2 # C-3 License plate light LH
R77 2 # C-4 License plate light RH
R96 2 Black B-3 R19 Rear wiring harness
#: Non-colored
86
6-3 [D6I0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0569A
87
[D6I0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
J: REAR END WIRING HARNESS OF WAGON
List of Items
Connector Connecting to
No. Pole Color Area No. Name
R26 7 # C-4 Rear combination light RH
R28 7 # C-2 Rear combination light LH
R32 3 # C-3 Rear accessory power supply
R36 5 Black C-4 Rear wiper relay
R37 2 # C-3 D33
Rear gate cord R38 4 # C-3 D34
R39 4 # C-3 D35
R76 2 # C-3 License plate light LH
R77 2 # C-3 License plate light RH
#: Non-colored
Connector Connecting to
No. Pole Color Area No. Name
D33 2 # C-3 R37
Rear wiring harness D34 4 # C-3 R38
D35 4 # C-3 R39
D39 2 # B-2 High-mount stop light
D40 1 # B-3 Rear defogger (Power)
D43 4 # A-3 Rear wiper motor
D46 2 Black A-3 Rear gate latch switch
D47 4 # A-3 Rear gate lock actuator
D48 1 # A-3 Rear defogger (Ground)
D58 2 # A-3 D59 Rear gate lock adapter cord
D59 2 # A-3 D58 Rear gate cord
#: Non-colored
88
6-3 [D6J0] WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
Location
H6M0570A
89
[D6J0] 6-3 WIRING DIAGRAM
6. Electrical Wiring Harness and Ground Point
MEMO:
90
6-3 WIRING DIAGRAM