1

Downloaded from www.Manualslib.com manuals search engine

2




















Downloaded from www.Manualslib.com manuals search engine

3






Downloaded from www.Manualslib.com manuals search engine

4

Removal of the riders saddle
Removal of the passengers saddle
Procedure 1.
- Open the saddle cover storage compartment.
- Remove:
. The screw.
. The saddle cover.
. The riders saddle.



Open the passengers saddle.
- Remove:
. The 2 upper pivot clips.
. The 2 pivot pins.

Downloaded from www.Manualslib.com manuals search engine

5


- Flip up the seat to the front of the vehicle.
- Remove:
. The 2 lower pivot clips.
. The 2 pivot pins.
- Remove the passenger seat.


Removal of a RH or LH grab handle
Procedure 2.
- Remove the grab handle trim.
- Remove the 2 nuts and the screw that secure the handle.
- Remove the grab handle.

Downloaded from www.Manualslib.com manuals search engine

6


Removal of a RH or LH taillight Removal of a
taillight bulb
- Remove the grab handle. See: Procedure 2.
- Remove the taillight. (1 screw).



- Remove the 4 screws from the taillight unit.
- Separate the 2 parts in order to reach the bulbs.



Downloaded from www.Manualslib.com manuals search engine

7


Removal of a RH or LH side cover
Procedure 3
- Remove:
- The riders saddle. See: Procedure I. Page: 30.
- The grab handles. See: Procedure 2. Page: 31. S Remove the rear cover and its trim.
(4 screw).



- Remove the 2 screws that secure the side cover linkage and the footboard.

Downloaded from www.Manualslib.com manuals search engine

8


- Push aside the footboard in order to clear side cover holder eyelet.
Remove the side cover.
- Disconnect the taillight.



Removal of the storage compartment
Procedure 4.
- Remove the side fairings. See: Procedure 3. Page: 32.
- Disconnect the plate light and the saddle opening contact switch.
Remove the storage compartment. (4 screws and 2 nuts).
Downloaded from www.Manualslib.com manuals search engine

9


When dismantling the splash guard, fit the screws with standard thread lock.



Removal of the tank covers
Procedure 5.
- The riders saddle. See: Procedure I.
- Page: 30.
Open the tank filler cap door.
Remove the 4 screws that secure the rear panel.
Remove the upper fairing.
Downloaded from www.Manualslib.com manuals search engine

10


- Remove the utility hanger. (2 screw).
- Remove 1 nut and 2 screws that secure the lower fairing.
- Remove the screw that secures the rear cover I footboard on each side of the vehicle. (1)
- Push slightly aside the cover I footboard assembly and remover the fuel tank cover
panel by sliding it backwards.


- Removal of a RH or LH footboard Procedure 6.
- Remove the tank cover panel. See:
Procedure 5.
- Remove the footboard mat.
- On each side remove:
. 8 plastic screws. (1)
. 3 washer head screws. 06 mm. (2)
. I washer head screw. 05 mm. (3)

Downloaded from www.Manualslib.com manuals search engine

11


- Press on the underbody panel in order to separate it from the footboard. (A)




- Separate the footboard from the rear fairing and bracket that anchors it to the body. (B)
- Separate the front of the footboard which is linked to the rear part of the leg shield panel.
(C)


Downloaded from www.Manualslib.com manuals search engine

12


- Removal of the front top cover panel
- Procedure 7.
- Remove the front top cover panel. (4 screw).



Removal of the headlight and sidelight assemblies
Removal of the headlight bulbs
- Remove the front top cover panel. See:
Procedure 7.
To reach the bulbs, remove the headlight.
(3 screw)

Downloaded from www.Manualslib.com manuals search engine

13

- Removal of the front shield panel
- Procedure 8.
- Remove the front top cover panel. See:
- Procedure 7.
- On each side remove:
. 2 plastic screws that secure the front leg shield to the underbody cover. (1)
. 2 plastic screws that secure the footboard the underbody cover. (2)
- Push aside the underbody cover to reach the screw that secures the front shield panel. (3)


- On each side remove:
. 5 plastic screws. (4)
. I washer head screw. 06 mm. (5)
. I washer head screw. 05 mm. (6)
- Disconnect the headlights.
- Remove the front shield panel.
Downloaded from www.Manualslib.com manuals search engine

14


- Removal of the rear shield panel
- Remove the ignition key.
- Remove the tank cover panel. See:
- Procedure 5.
- Remove the front top cover panel. See:
- Procedure 7.
- Remove:
The ignition switch trim.
The handlebar upper fairing (8 screw) (1).



- On each side remove:
2 plastic screws that secure the front leg shield to the underbody cover.
2 plastic screws that secure the footboard to the underbody cover.
- Push aside the underbody cover to reach the screw that secures the front shield panel. (2)
Downloaded from www.Manualslib.com manuals search engine

15


- On each side remove:
6 plastic screws. (3)
2 washer head screws. 06 mm. (4)



- Separate the front shield panel from the rear shield panel in order to reach the bracket that connects the rear
shield panel to the footboard. (A)
- Pull upwards the lower part of the shield panel in order to separate it from the footboard.

Downloaded from www.Manualslib.com manuals search engine

16


- Relove the eyelet (B) from the shield panel and the eyelet (C) from the instrument cluster
fairing in order free the rear shield panel.



- Topple the rear shield panel while separating it from the footboards in order to reach the
header tank and the accessory plug.
- Remove the header tank. (Right side).
- Disconnect the accessory plug. (Left side).
- Remove the rear shield panel.
Downloaded from www.Manualslib.com manuals search engine

17


- Removal of the dirt shield
- Remove the front shield panel.
See: Procedure 8.
- Remove the center screw which secures the dirt shield to the underbody cover.
- Disconnect the speed sensor.
- Pull the speed sensor control out of the dirt cover.
- Lift the front of the vehicle while making sure the wheel is in line with the vehicle.
- Remove the dirt cover by sliding it behind the wheel as shown.


- Removal of the battery holder Procedure 9.
- Remove the tank cover panel. See: Procedure 5.
- Disconnect and remove the battery.
- Unclip from the battery holder:
The fuses. (1)
The relays. (2)
The diagnosis plug.(3)
- Remove the battery bracket. (2 screws and I nuts).

Downloaded from www.Manualslib.com manuals search engine

18

- Removal of the instrument cluster
- Remove:
- The front top cover panel. See: Procedure 7.
The wind deflector.
The handlebar upper fairing.
- On each side remove:
1 plastic screw. (1)
1 washer head screw. 05 mm. (2)
1 washer head screw. 06 mm. (3)


- Press the locking system (1) to actuate the
positioning lever (2) of the instrument clusters connector.
- Push the lever all the up (A) in order to remove the connector from the instrument cluster.
- Remove the instrument cluster fairing.

Note: When connecting, the lever must be pushed all the way to (A) in order not to damage the
connector.



Downloaded from www.Manualslib.com manuals search engine

19



PIAGGIO MOTOR SERVICE STATION MANUAL


























Engine Master 500 cc




















Downloaded from www.Manualslib.com manuals search engine

20



SERVICE STATION MANUAL
PEUGEOT SATELIS 500 cc




This manual has been prepared by Piaggio & C. S.p.A. for use in the workshops of authorised Piaggio sub-
agents.
It is assumed that the person utilising this manual for servicing or repairing Piaggio vehicles has a knowledge
principles of mechanics and standard procedures for vehicle repair. Any important changes in vehicle
or specific repair operations will be divulged by means of updates to this manual.
Satisfactory repair or service cannot be achieved without the necessary equipment and tools. Refer
of this manual concerning specific tools and equipment and the special tools catalogue.

Critical information in the manual is indicated as follows.

N.B.: Important information for facilitating and explaining a procedure.

Warning - Procedures that must be followed to avoid damage to the vehicle.

Caution - Procedures that must be followed to eliminate the risk of injury to repair / service personnel.























Downloaded from www.Manualslib.com manuals search engine

21

Specifications (500 cc 4-stroke, 4-valves H2 0 engine)

ENGINE
Type .............................................................................................................single-cylinder, 4 stroke
Bore.........................................................................................................................................92 mm
Stroke.......................................................................................................................................69 mm
Displacement........................................................................................................................460 cm3
Compressionratio....................................................................................................................10.5 : 1
Timing ..............................................................................................chain-operated overhead
single-shaft flywheel side, integrated phonic wheel, 4- valves and automatic starting valve lifter

Valves play: intake............................................................................................................... 0.20 mm
exhaust............................................................................................................ 0.20 mm
Valves play
adjustment........................................................................................ threaded register on equalizers
Idle speed......................................................................................................................145050 rpm
CO% value ................................................................................................................................. 11.
Starting system ............................................................................................................electric starter
Lubrication........................................... trochoid pump (inside the crankcase), oil filter and pressure
adjustment by-pass

Lubrication pressure.................................................................................................................. 4 bar
Minimum allowed pressure (at 100C) ................................................................................... 0.8 bar

Fuel system ........................................................electronic injection with electric fuel pump, throttle
body 38mm and single injector

Max power
(at crankshaft) ......................................................................................29 kW (39 CV) bei 7250 rpm
Max torque
(at crankshaft) .................................................................................... 40 Nm (4 Kgm) bei 5500 rpm
Cooling system.................... liquid, by means of motorized pump, 3-way thermostat and electric
fan.
Transmission .............................automatic speed variator by means of expanding pulleys, V-belt,
automatic clutch, reduction gear, and transmission compartment cooling by air forced-circulation.

Ignition type .................... high efficiency inductive type integrated with injection, variable spark
advance and separated high voltage coil

Spark advance
(before T.D.C.) ............... variable controlled by injection
power unit
Spark plug .............................................................................CHAMPION RG 6 YC NGK CR7 EKB

Engine-wheel ratio ............................................................................. short: 1/11.988 long: 1/ 4.86
Engine oil ................................................................................................SAE 5W/40 exceeding API

SJ specifications
Quantity .................................................................................................. ~ 1.7 l
Hub oil........................................................................................................................TUTELA ZC 90
Quantity ....................................................................................................................................250cc
Cooling system capacity ........................................................................................................... ~ 1.8



Downloaded from www.Manualslib.com manuals search engine

22
Spark plug
Check and replacement


Warning
- Remove the spark plug when the engine cold. Replace the spark plug every 12,000 Km. The use of
unsuitable control units or spark plugs other than those specified can seriously damage the engine.
Recommended spark plug: CHAMPION RG 6 YC NGK CR 7 EKB
- Put the vehicle on its central stand.
- Open the door on the left side of the vehicle by levering in the recess in the lower part of the door after
removing the screw.
- Disconnect the spark plug high voltage cable cap;
- Unscrew the spark plug with the spanner provided; check the spark plug to see if the insulator is cracked,
the electrodes are worn out or excessively sooty.
Also check the condition of the sealing washer and measure
: 0.7 - 0.8 mm
- If necessary adjust the gap by carefully bending the side electrode. If the spark plug has any of the
defects mentioned above replace it with a plug of the recommended type;
- Insert the plug into the hole with the proper inclination, screw it in fully by hand and then tighten it with the
specially designed spanner.
Tightening torque: 10 Nm (1 Kgm)
- Push the spark plug cap all the way down onto the spark plug and then proceed to the reassembly.


Air filter

- Remove the left-hand lower side panel
- Remove the cleaner cap after unscrewing the eight fixing screws, including one screw of the knob type.
- Pull out the filter element.
- Replace the air filter with a new one.
N.B.: Check and if necessary blow the air filter every 6,000 km. Direct the air jet from the inside to the
outside of the filter (i.e. in the opposite direction to the air flow during normal engine operation).
Warning
- If the vehicle is mostly used on dusty roads, the air filter needs to be cleaned and replaced at
shorter intervals than indicated in the Maintenance Schedule.
Downloaded from www.Manualslib.com manuals search engine

23
Warning
- Do not run the engine if the air filter is not in place as this would result in excessive wear of the cylinder
and piston as well as in damage to the throttle body.








Engine oil level
In four-stroke engines oil is used to lubricate the valve gear components, the crankshaft bearings and the
thermal unit. A lack of engine oil can cause serious damage to the engine.
In all four-stroke engines, oil deterioration and consumption are, to some extent, normal, especially during
running-in. Consumption partly depends on the riding style (for example, constantly riding at full throttle
increases oil consumption).

Checking the oil level
Perform this operation when the engine cold, as described
below:
1) Put the vehicle on its central stand on a flat surface.
2) Unscrew dipstick A, dry it with a clean cloth and refit by screwing it completely.
3) Remove the dipstick again and check that the oil level is between the MAX and MIN marks on the
dipstick; top up if necessary.
Il riferimento del livello di MAX indica una quantit di circa 1700 cc di olio nel motore.
The level will be lower if checked after using the vehicle
(i.e. when the engine is hot). To obtain a correct indication
of the oil level, wait for at least 10 minutes after switching off the engine.
When the oil level is at MAX the engine contains 1700 cc of oil.








Downloaded from www.Manualslib.com manuals search engine

24

Replacing the filter

Warning
- Do not dispose of the oil in the environment.
Carry out the disposal of the oil, the gasket and
the filter in accordance with the law.

Warning - To avoid burns, take care not to touch hot engine parts.

- Remove the silencer.
- Remove filler plug A.
- Remove and clean the drain plug gauze strainer with
compressed air.
- Using a strap wrench for filters, remove cartridge filter C.
- Ensure that the O-rings on the prefilter and the drain
plug are in good condition.
- Lubricate the O-rings and then refit the gauze strainer
and the oil drain plug. Tighten the drain plug with the
prescribed torque.
- Fit a new cartridge filter after lubricating the O-ring.
Turn in until the gasket makes contact and then screw
it with the prescribed torque.
- Reinstall the silencer.
- Add engine oil as previously described.

Tightening torque: Oil filter: 12 - 16 Nm
Recommended oil: Selenia HI Scooter 4 Tech

------------------------------------------------------------------------------------------------------------------------------------------------------------

Checking the hub oil level

Put the vehicle on the central stand on level ground.
- Unscrew oil dipstick A, wipe it with a clean cloth,reinsert it and then screw it in fully.
- Pull out the dipstick again and check that the oil level is between the MIN and MAX marks (see figure); if
the level is below the MIN mark, top up with oil.
- Reinsert the dipstick and screw it tight. MAX



----------------------------------------------------------------------------------------------------------------------------------------------
Renewing the hub oil

- Remove oil filler plug A.
- Unscrew oil drain plug B and drain all the oil.
- Retighten the oil drain plug and then fill the hub with
fresh oil.
Downloaded from www.Manualslib.com manuals search engine

25
Hub oil capacity: ~ 250 cc
Recommended oil: TUTELA ZC 90



------------------------------------------------------------------------------------------------------------------------------------------------------------

Engine cooling Adding coolant and bleeding air from the system.

The level of the fluid must be checked every 6,000 km when the engine is cold.
Follow these steps:
- Put the vehicle on the central stand on level ground.
- Remove the expansion tank cap and top up if the coolant is below or near the MIN level in the expansion
tank. The level of the fluid should always be between the MIN and MAX marks.
- To have an indication of the coolant level, refer to the groove in the plastic strip that can be seen through
the coolant filler hole. The upper and lower parts of the groove correspond to the MAX and MIN levels
respectively.
- The coolant consists of a 50 percent mixture of demineralized water and antifreeze solution with a base of
ethylene glycol and corrosion inhibitors. Total coolant capacity: ~ 1.8 lt
- To check the presence of air in the circuit follow the procedure described in Chapter 11 - Cooling.
- Switch off the engine and allow it to cool down. After a few minutes, remove the expansion tank cap and
check the level of the fluid.
- If necessary, top up by pouring fresh coolant into the expansion tank up to the correct level.





Warning
- To prevent the coolant from leaking out of the expansion tank during use, be sure to never exceed the
MAX level when refilling.





Downloaded from www.Manualslib.com manuals search engine

26

Water pump

If the water pump becomes noisy or liquid leaks through the pump drain hole, check the water pump as
described
in Chapter 5-Flywheel cover. Follow these steps:
- Put the vehicle on the central stand on level ground.
- Remove the lower right-hand side panel and the right-hand footboard as described in Chapter 8-
Bodywork of the X9- 500 cc manual;
- Remove the sleeves from the water pump cover and the filler cap from the expansion tank and empty the
cooling circuit.
- Drain the cooling system by removing the sleeves located on the water pump cover and the plug located
on the expansion tank.
- After solving the problem and refitting all components, fill and bleed the cooling circuit again.

Warning
- Perform the operation when the engine is cold.
- Remove the water pump cover shown in the figure after loosening the six fixing screws.
- Cooling circuit capacity: ~ 1.8 lt.
- As described in Chapter 5-Engine of the X9 500cc manual, partially drain the system and overhaul the
pump.





Checking the valve gear timing

- With a wrench of the TORX type, remove the timing check plug located on the flywheel cover.
- Remove the transmission cover and relevant insulation as described in Chapter 3-Automatic
Transmission.
- Remove the head cover as described in Chapter 7- Thermal Unit and Timing System.
- Turn the driving shaft by means of the driving pulley until the reference mark on the magneto support
coincides with the mark on the flywheel cover (TDC).
- Make sure that the reference mark on the phonic wheel is aligned with the mark on the head. If
necessary, turn the driving shaft accordingly.



Downloaded from www.Manualslib.com manuals search engine

27
Valves play check/adjustment

- Check the valves play after aligning the valve timing reference marks as described in the previous
section.
- Check that the valve-register play corresponds with the indicated values by means of a feeler gauge. If
the valve play values, intake and exhaust respectively, do not correspond with those indicated below,
adjust them by loosening the check nut and acting on the register with a screwdriver, as shown in the
figure.

Intake: 0.15 mm cold engine
Exhaust: 0.15 mm cold engine



Checking pressure at the end of the compression
- Remove the spark plug cap with the engine cold.
- Remove the spark plug.
- Fit a compression control gauge in the spark plug seat by means of a 10mm plug connection. Tighten to
the prescribed torque.
- Start the engine by means of the starting motor and with throttle body fully open until the gauge pointer
stops. If the pressure is between 8 - 11 bar, remove the tool and reassemble the spark plug.
- If the measured pressure is lower than the recommended values, check the engine revs number; if it is
lower than 450 rpm, check the starting system; if the revs number is correct or slightly higher, check the
timing. If no troubles are found, proceed as follows:
- Check that the cylinder gasket is the right one.
- Check the thermal zone sealings (compression rings-valves).

Tightening torque:
Compression test connection: 10 Nm


External transmission cover
- Unloose the 5 fixing screws
- Remove the external plastic cover




Downloaded from www.Manualslib.com manuals search engine

28
Transmission cover
- Unloose the 7 fixing screws
- Remove the cover and net filter

N.B.: Disassemble the net filter only if it is to be replaced.




Belt antiflapping roller
- Check that the roller is in good condition and that it
turns freely.
- Unloose the fixing screw with a 13 mm wrench
- Remove the roller and relevant bearing.

N.B.: If the roller does not turn freely, replace it.





Driving pulley
- Turn the pulley central nut with a 27 mm wrench to align the internal holes horizontally, therefore allowing
for the specific tool fitting.

Specific tool: Driving pulley lock wrench 020474Y


Downloaded from www.Manualslib.com manuals search engine

29

- First fit the specific tool stop ring on the pulley until the groove is fully in contact.
- Afterwards, insert the tool so that the studs on the ring fit the holes in the tool.
- Tighten, also manually, the two fixing nuts of the tool
- Unloose the central nut.
- Remove the cup washer and the plain washer.
- Remove the fixed driving half pulley.
- Remove the washer to bush connection.





- Move the belt downwards.
- Hold the roller stop plate, remove the mobile driving half pulley with its bush and rear washer, taking care
not to let the rollers come out.




Driven pulley axle support
- To be able to fit the specific tool for removal of the driven pulley shaft nut, unloose the 2 upper screws of
the driven pulley axle support.
- Manually turn the clutch housing as to partially uncover one of the holes in the driven pulley axle support.


Downloaded from www.Manualslib.com manuals search engine

30

- Insert the specific tool on the driven pulley axle support, checking that the tooth fits the hole in the
housing previously uncovered, and that it is resting on the support.
- Tighten the 2 fixing screws.
- Unloose the driven pulley shaft nut.

Specific tool: Clutch housing stop tool 020473Y



- Remove the specific tool
- Unloose the 2 remaining fixing screws of the driven pulley axle support.
- Remove the driven pulley axle support and the washer.
- Remove the spacer below.




Clutch housing - Remove the clutch housing.


Downloaded from www.Manualslib.com manuals search engine

31

- Check that the clutch housing shows no signs of wear or damage.
- Measure the clutch housing I.D.
Standard value: 160.2 mm
Max value: 160.5 mm

N.B.: Check that the measured eccentricity is max 0.2 mm





Driven pulley assembly
- Remove the driven pulley assembly and relevant belt.




Clutch disassembly

- Remove the clutch and driven pulley by means of the specific tool;
- Prepare the tool with the pins screwed in the E position on the internal side;
- Assemble the driven pulley assembly on the tool and insert the pins in the ventilation holes;
- Bring the rear stop screw in contact with the fixed driven pulley, as shown in the figure.

Warning
- Put the tool in a vice firmly. Do not overtighten the rear screw to avoid buckling the tool.

Remove the fixing ring nut with the specific spanner of 55 mm.
- Unloose the tool screw and dismount the driven pulley, clutch, spring with sheath assembly

Specific tools:
Driven pulley spring compressor 020444Y
55 mm spanner 020444Y009
Ring 020444Y010






Downloaded from www.Manualslib.com manuals search engine

32




Pins stop collar
- Remove the collar by means of 2 screwdrivers.





- Remove the 4 guide pins.
- Remove the mobile driven half pulley.












Downloaded from www.Manualslib.com manuals search engine

33

Fixed driven half pulley bearings

- Check that the bush shows no signs of wear or damage; if necessary, replace the fixed driven half pulley.
- Remove the stop ring with the pliers.





- Remove the ball bearing by inserting the specific tool in the roller bearing.

N.B.: Hold the pulley to avoid damaging the thread.


Specific tools:

Handle 020376Y
24 mm adapter 020456Y
20 mm guide 020363Y

N.B.: If the bearings are overhauled with the driven pulley unit assembled, make sure to support the unit with bell
001467Y002.



- Remove the roller bearing by means of the specific tool, supporting the fixed half pulley with the bell.

Specific tools:
Handle 020376Y
28x30 mm adapter 020375Y
25 mm guide 020364Y
Bell 001467Y002



Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
22
CARTER
CARTER
CRANKASE
KURBELGEHUSE
CARTER
T. 2
1 CM11451750011 FCI Carter motore Carter moteru Crankcase Kurbekgrhuse Carter motor
1 CM11451750021 FC2 Carter motore Carter moteru Crankcase Kurbekgrhuse Carter motor
1 CM11451750031 FC3 Carter motore Carter moteru Crankcase Kurbekgrhuse Carter motor
1 CM11451750041 FC4 Carter motore Carter moteru Crankcase Kurbekgrhuse Carter motor
2 827951 4 Prigioniero Goujon Stud Stiftschraube Esprrago
3 828909 12 Vite Vis Screw Schraube Tornillo
4 82656R 2 Cuscinetto Roulement Bearing Lager Cojinete
5 828114 1 0,4 Guarnizione Joint Gasket Dichtung Empaque
6 411311 2 Tappo Bouchon Plug Verschlu Tapa
7 484034 1 Ugello Buse Nozzle Dse Boquilla
8 239388 4 Spina Goujon Dowel Zapfen Pasador
9 82668R 2 Cuscinetto Roulement Bearing Lager Cojinete
10 006647 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
11 829195 1 Paraolio Pare-huile Oil seal Dichtring Sello de lub.
12 832130 1 Asta olio Jauge niveau dhuile Oil dipstick lmestab Varilla
13 827085 1 Guarnizione Joint Packing Dichtung Junta
14 833701 1 Cuscinetto Palier Bearing Radiallager Cojinete
15 485912 1 Cuscinetto Palier Bearing Radiallager Cojinete
16 825238 1 Anello tenuta Bague dtanchite Oil seal Dichtring Reten de ac.
17 825233 1 Cuscinetto Palier Radial Radiallager Cojinete
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
23
T. 2
CARTER
CARTER
CRANKASE
KURBELGEHUSE
CARTER
18 000674 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
19 833513 2 Prigioniero Goujon Stud Stiftschraube Esprrago
20 478115 4 Grano Goujon Dowel Stift Clavija
21 414838 1 Vite Vis Screw Schraube Tornillo
22 828922 1 Vite Vis Screw Schraube Tornillo
23 825649 1 Ugello Buse Nozzle Dse Boquilla
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
24
ALBERO MOTORE
VILEBREQUIN
CRANKSHAFT
KURBELWELLE
CIGENAL
T. 3
1 828205 1 Distanziale Entretoise Spacer Distanzstck Distanciador
2 841456 1 Kit contralbero Kit contre-arbre Countershaft-gears Bausatz Kit contraeje
ingranaggi engrenages kit Getriebezwischenw. engranajes
3 8322150001 1 FC1 Albero motore Arbre moteur Crankshaft Kurbelwelle Cigueale completo
3 8322150002 1 FC2 Albero motore Arbre moteur Crankshaft Kurbelwelle Cigueale completo
4 830129 4 Vite Vis Screw Schraube Tornillo
5 830012 1 Rasamento Epaulement Shim Ausgleichsscheibe Ras.
6 000267 2 Chiavetta Clavette Key Keil Chaveta
7 830112 1 Dado Ecrou Nut Mutter Tuerca
8 829752 1 Distanziale Entretoise Spacer Distanzstck Distanciador
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
25
GRUPPO CILINDRO-PISTONE-SPINOTTO
ENSEMBLE CYLINDRE-PISTON-AXE DE PISTON
CYLINDER-PISTON-WRIST PIN, ASSY
GRUPPE ZYLINDER-KOLBEN-KOLBENBOLZEN
GRUPO CILINDRO-PISTON-EJE DE PISTON
T. 4
1 832811 1 Gr.cil.-pist.-spin. Gr. cylindre- Cylinder-piston- Zylinder/Kolben kpl Gr. cilindro-pistn-
piston-axe wrist pin assy. eje
2 8328120001 1 FC1 Gr. pistone-spinotto Ens. piston-Axe Piston-wrist pin Gr. Kolben-bolzen Gr. pistn-buln
de pist. assy.
2 8328120002 1 FC2 Gr. pistone-spinotto Ens. piston-Axe Piston-wrist pin Gr. Kolben-bolzen Gr. pistn-buln
de pist. assy.
2 8328120003 1 FC3 Gr. pistone-spinotto Ens. piston-Axe Piston-wrist pin Gr. Kolben-bolzen Gr. pistn-buln
de pist. assy.
2 8328120004 1 FC4 Gr. pistone-spinotto Ens. piston-Axe Piston-wrist pin Gr. Kolben-bolzen Gr. pistn-buln
de pist. assy.
3 828116 2 Anello Anneau Ring Ring Anillo
4 827820 1 Spinotto Axe Pin Zapfen Eje
5 827707 1 Raschiaolio Segment racleur Scraper ring Kolbenring Rascador de
dhuile labstreifer aceite
6 827706 1 Raschiaolio Segment racleur Scraper ring Kolbenring Rascador de
dhuile labstreifer aceite
7 832770 1 Segmento di compr. Segment de compr. Compr. ring Kompressions- Aro de compresion
Kolbenring
8 830275 1 0,8 Guarnizione Joint Packing Dichtung Junta
8 830276 1 0,6 Guarnizione Joint Packing Dichtung Junta
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
26
GRUPPO CILINDRO-PISTONE-SPINOTTO
ENSEMBLE CYLINDRE-PISTON-AXE DE PISTON
CYLINDER-PISTON-WRIST PIN, ASSY
GRUPPE ZYLINDER-KOLBEN-KOLBENBOLZEN
GRUPO CILINDRO-PISTON-EJE DE PISTON
T. 4
8 830277 1 0,4 Guarnizione Joint Packing Dichtung Junta
9 834254 1 Guarnizione Joint Packing Dichtung Junta
10 434541 2 Vite Vis Screw Schraube Tornillo
11 288245 2 Dado Ecrou Nut Mutter Tuerca
12 178790 4 Rondella Rondelle Washer U.Scheibe Arandela
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
27
T. 5
GR. TESTA-VALVOLE
ENSEMBLE CULASSE-SOUPAPES
HEAD-VALVES
EINHEIT KOPF-VENTIL
CULATA-VALVULAS
1 285846 8 Semiconi Demi-cnes Half cone Halbkonusse Semiconos
2 828396 4 Scodellino sup. Coupelle sup. Upper cap Oberer Caja de cojinete
ventilfederteller sup.
3 826103 4 Molla Ressort Valve spring Feder Muelle
4 436438 4 Anello di tenuta Joint spie Oil seal Dichtring Retn de aceite
5 826256 4 Scodellino inf. Coupelle inf. Lower cap Unterer Caja de cojinete
ventilfederteller inf.
6 828321 2 SCA Valvola Soupape Valve Ventil Vlvula
6 828322 2 ASP Valvola Soupape Valve Ventil Vlvula
7 830008 1 Guarnizione Joint Packing Dichtung Junta
8 831039 1 Testa cilindro compl. Culasse compl. Cylinder head ass. Zylinderkopf komp. Culata compl.
9 063435 1 Cappuccio Cache Cap Kappe Capuchn
10 430045 1 Vite Vis Screw Schraube Tornillo
11 828646 1 Sensore Capteur Sensor Sensor Sensor
12 5847685 1 Sensore Capteur Sensor Sensor Sensor
13 434541 1 Vite Vis Screw Schraube Tornillo
14 827018 2 Prigioniero Goujon Stud Stiftschraube Esprrago
15 830278 3 Vite Vis Screw Schraube Tornillo
16 CM001915 2 Fascetta Collier Clamp Schelle Abrazadera
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
28
T. 5
GR. TESTA-VALVOLE
ENSEMBLE CULASSE-SOUPAPES
HEAD-VALVES
EINHEIT KOPF-VENTIL
CULATA-VALVULAS
17 832783 4 Dado Ecrou Nut Mutter Tuerca
18 827953 2 Prigioniero Goujon Stud Stiftschraube Esprrago
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
29
GRUPPO SUPPORTO BILANCIERI
ENSEMBLE SUPPORT BALANCIERS
ROCKER LEVERS SUPPORT
EINHEIT KIPPHEBELHLTER
SOPORTE BRAZO OSCILANTE
T. 6
1 484819 4 Dado Ecrou Nut Mutter Tuerca
2 484654 4 Vite Vis Screw Schraube Tornillo
3 8260285 1 SCA Bilanciere Culbuteur Equalizer Schwinghebel Balancn
4 8293655 1 Asse a camme Axe cames Cam axle Nockenwelle Eje de levas
5 827991 2 Asse bilanciere Axe culbuteur Equalizer axle Schwinghebelwelle Eje balancn
6 829198 1 Corona distribuzione Couronne distribution Timing gear Zahnkranz Corona distribucion
Ventilsteuerung
7 829071 1 Contrappeso Contrepoids Counter weight Gegengewicht Contrapeso
8 018538 1 Vite Vis Screw Schraube Tornillo
9 829252 1 Molla Ressort Spring Feder Muelle
10 831167 1 Lamierino Tle Sheet Blechstck Lmina
11 831153 3 Vite Vis Screw Schraube Tornillo
12 8311615 1 Massetta Masse Decompression Dekompressions Masa de
decompressione dcompression counterweight masse decompresion
13 829097 1 Guarnizione Joint Packing Dichtung Junta
14 829247 1 Campana Cloche Decompression bell Dekompressionskorb Campana de
decompressione dcompression decompresion
15 829287 1 Vite Vis Screw Schraube Tornillo
16 8260275 1 ASP Bilanciere Culbuteur Equalizer Schwinghebel Balancn
17 829211 1 Ruota fonica Codeur Encoder Encoder Tonrad Encoder
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
30
T. 7
COPERCHIO TESTA
COUVERCLE CULASSE
CYLINDER HEAD COVER
ZYLINDERKOPFABDECKUNG
TAPA CULATA
1 438073 1 CMP Candela accensione Bougie dallumage Spark plug Zndkerze Buja de encendido
1 829981 1 NGK Candela accensione Bougie dallumage Spark plug Zndkerze Buja de encendido
2 830820 1 Guarnizione Joint Packing Dichtung Junta
3 830248 6 Vite Vis Screw Schraube Tornillo
-abdeckung
4 830819 1 Coperchio testa Couvercle culasse Cylinder head cover Zylinderkopf- Tapa culata
-abdeckung
5 830249 6 Tampone Silentbloc Buffer Puffer Silent-block
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
31
T. 8
PULEGGIA MOTRICE
POULIE MOTRICE
DRIVING PULLEY
TREIBENDE RIEMENSCHEIBE
POLEA MOTRIZ
1 833291 1 Contenitore rulli Logement roleaux Roller housing Reglergehausehalfte Alojamento rodillos
2 842175 3 Pattino Doigt Shoe Gleitauflage Patn
3 830901 1 Contrasto rulli Couvercle rouleaux Rollers cover Rollenanschlag Contraste rodillos
4 825381 1 Distanziale Entretoise Spacer Distanzstck Distanciador
5 830899 8 Rullo Rouleau Roller Rollen Rodillo
6 832738 1 Cinghia trapezoidale Courroie trapz V-belt Keilriemen Correa trapezoidal
7 832697 1 Semipuleggia Demi-poulie Half pulley Halbscheibe Semipolea
8 829205 1 Rondella Rondelle Washer U.Scheibe Arandela
9 829203 1 Rondella Rondelle Washer U.Scheibe Arandela
10 829251 1 Molla a tazza Ressort Cup spring Tassenfeder Muelle
diaphragme
11 829232 1 Dado Ecrou Nut Mutter Tuerca
12 834304 1 Puleggia smorzatrice Poulie Damping pulley Dmpferscheibe Polea
damortissement amortiguadora
13 829693 1 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
32
PULEGGIA CONDOTTA
POULIE ENTRAINEE
DRIVEN PULLEY
GETRIEBENE RIEMENSCHEIBEN
POLEA CONDUCIDA
T. 9
1 82627R 1 Cuscinetto Roulement Bearing Lager Cojinete
2 825382 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
3 829808 1 Astuccio a rullini Cage roul. Roller cage Rollenlagerkafig Jaula rodillos
4 832774 1 Semipuleggia Demi-poulie Half pulley Halbscheibe Semipolea
5 828978 4 Perno Pivot Pin Zapfen Perno
6 832808 1 Semipuleggia Demi-poulie Half pulley Halbscheibe Semipolea
7 825239 2 Anello tenuta Bague dtanchite Oil seal Dichtring Reten de ac.
8 825237 1 Guarnizione Joint Packing Dichtung Junta
9 828974 1 Scodellino Rondelle dar Stop washer Federaufnahme Platillo
10 831098 1 Molla variatore Ressort variateur Converter spring Feder Variator Muelle variador
11 825384 1 Scodellino frizione Coupelle embrayage Clutch cup Federteller Kupplung Tapa embrague
12 8405775 1 Frizione centrifuga Embrayage Centrifugal clutch Fliehkraftkupplung Embrague
compl. centrifuge compl. assy. kompl. centrfugo
13 825385 1 Ghiera Douille Ring nut Gewindering Casquillo
14 825176 1 Tamburo frizione Tambour dembr. Clutch drum Kupplungstrommel Tambor de embr.
15 842559 1 Puleggia condotta Groupe embrayage Driving pulley Riemenscheibe Polea conducida
16 827116 1 Dado Ecrou Nut Mutter Tuerca
17 840319 1 Rondella Rondelle Washer U.Scheibe Arandela
18 828984 1 Guarnizione Joint Packing Dichtung Junta
19 825763 1 Distanziale Entretoise Spacer Distanzstck Distanciador
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
33
PULEGGIA CONDOTTA
POULIE ENTRAINEE
DRIVEN PULLEY
GETRIEBENE RIEMENSCHEIBEN
POLEA CONDUCIDA
T. 9
20 840320 1 Rondella Rondelle Washer U.Scheibe Arandela
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
34
T. 10
RAFFREDDAMENTO CARTER
REFROIDISSEMENT CARTER
CRANKCASE COOLING
KHLUNG KURBELGEHUSE
REFRIGERACION CARTER
1 8423545 1 Coperchio Couvercle Transmission cover Getriebeabdeckung Tapa transmision
trasmissione transmission
2 840277 1 Cuscinetto Roulement Bearing Lager Cojinete
3 270793 2 Vite Vis Screw Schraube Tornillo
4 833318 1 Filtro aria Filtre air Air filter Luftfilter Filtro de aire
5 833320 2 Insonorizzante Insonorisant Soundproofing Schalldmpfung Insonorizante
material
6 414834 7 Vite Vis Screw Schraube Tornillo
7 825667 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
8 833314 1 Coperchio insonoriz. Couvercle insonoris. Transm. Soundproof. Schallgedmp. Deckel Tapa insonoriz.
trasm. Transm. cover fr Antrieb Transm.
9 833663 2 Vite Vis Screw Schraube Tornillo
10 833664 2 Vite Vis Screw Schraube Tornillo
11 842355 1 Deflettore Dflecteur Deflector Deckblech Deflector
12 575249 2 Vite Vis Screw Schraube Tornillo
13 833321 2 Insonoriz. coperchio Insonoris.couvercle Cover soundproof. Schalldmpfung Insonorizante tapa
material Deckel
14 259348 2 Vite Vis Screw Schraube Tornillo
15 270793 4 Vite Vis Screw Schraube Tornillo
16 575249 4 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
35
T. 10
RAFFREDDAMENTO CARTER
REFROIDISSEMENT CARTER
CRANKCASE COOLING
KHLUNG KURBELGEHUSE
REFRIGERACION CARTER
17 620876 1 Protezione Protection Guard Schutz Proteccion
18 016670 3 Rondella Rondelle Washer U.Scheibe Arandela
19 252099 3 Rivetto Rivet Rivet Niete Remache
20 841490 1 Convogliatore Canalisation Conveyor Luftzufuhr Deflector
21 840439 1 Coperchio Couvercle Cover Deckel Tapa
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
36
T. 11
POMPA OLIO - AVVIAMENTO ELETTRICO
POMPE HUILE - DMARRAGE LECTIQUE
OIL PUMP - ELECTRIC STARTER
LPUMPE - ELEKTRISCHER STARTER
BOMBA DE ACEITE - ARRANQUE ELECTRICO
1 825737 1 Distanziale Entretoise Spacer Distanzstck Distanciador
2 827886 1 Asta tendicatena Axe tendeur de Chain tightener rod Kettenspanner Barra tens. de
chane cadena
3 830129 1 Vite Vis Screw Schraube Tornillo
4 825281 1 Pompa olio compl. Pompe huile compl. Oil pump assy. lpumpe kompl. Bomba del aceite
compl
.
5 827889 1 Catena distribuz. Chane de distribut. Timing chain Ventilsteuerkette Cadena distribuc.
6 433477 2 Vite Vis Screw Schraube Tornillo
7 830064 1 Paratia olio Paroi huile Oil wall l-Zwischenwand Separador aceite
8 830061 2 Vite Vis Screw Schraube Tornillo
9 828118 1 Guarnizione Joint carter/pompe Oil pump/crankcase Dichtung Junta carter/bomba
carter/pompa olio huile gasket Motorgehuse/ lpumpe aceite
10 827882 1 Pattino fisso Patin fixe Fixed pad Fester Laufschuh Patn fijo
11 414837 2 Vite Vis Screw Schraube Tornillo
12 82699R 1 Motorino avviamento Moteur du dmarreur Starter motor Startermotor Motor de arranque
13 8321174 1 Limitatore Limiteur de couple Torque limiter Drehmomentbegrenzer Limitador de par
coppia compl. compl. compl. kompl.
14 826033 1 Filtro olio aspiraz. Filtre huile admis. Intake oil filter l-Ansaugfilter Filtro aceite admis.
15 826165 1 Tappo filtro olio Bouchon filtre huile Oil filter plug lfilterverschlu Tapa filtro aceite
16 285536 1 O-ring O-Ring O-Ring O-Ring Anillo OR
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
37
T. 11
POMPA OLIO - AVVIAMENTO ELETTRICO
POMPE HUILE - DMARRAGE LECTIQUE
OIL PUMP - ELECTRIC STARTER
LPUMPE - ELEKTRISCHER STARTER
BOMBA DE ACEITE - ARRANQUE ELECTRICO
17 584843 1 Cavetto di massa Cable masse Ground cable Masse kabel Cable masa
18 031086 1 Vite Vis Screw Schraube Tornillo
19 016406 1 Rondella Rondelle Washer U.Scheibe Arandela
20 288474 1 Guarnizione Joint Packing Dichtung Junta
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
38
VOLANO MAGNETE
VOLANT MAGNETIQUE
FLYWHEEL MAGNETO
LICHTMASCHINE
VOLANTE MAGNETICO
T. 12
1 018575 2 Vite Vis Screw Schraube Tornillo
2 479515 6 Rondella Rondelle Washer U.Scheibe Arandela
3 58040R 1 Rotore compl. Rotor compl. Rotor, assy. Rotor kpl. Rotor compl.
4 82736R 1 Statore compl. Stator, assy. Backplate, assy. Ankerplatte kpl. Estator compl.
5 840893 6 Vite Vis Screw Schraube Tornillo
6 827116 1 Dado Ecrou Nut Mutter Tuerca
7 122637 3 Vite Vis Screw Schraube Tornillo
8 82737R 1 Corona dentata Couronne dente Ring gear Zahnrad Corona dentada
9 825725 1 Rondella Rondelle Washer U.Scheibe Arandela
10 828109 1 Lamierino Tle Sheet Blechstck Lmina
11 015715 3 Vite Vis Screw Schraube Tornillo
12 000097 1 Chiavetta Clavette Key Keil Chaveta
13 825431 1 Ruota libera compl. Roue libre compl. Free wheel assy. Freilauf kpl. Rueda libre compl.
14 830886 1 Lamierino Tle Sheet Blechstck Lmina
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
39
T. 13
COPERCHIO VOLANO - FILTRO OLIO
CARTER VOLANT - FILTRE HUILE
FLYWHEEL COVER - OIL FILTER
SCHWUNGRADDECKEL - LFILTER
TAPA VOLANTE - FILTRO DE ACEITE
1 8415115 1 Coperchio volano Carter volant Flywheel cover Schwungraddeckel Tapa volante
2 486216 1 Inserto ceramico Pice cramique Ceramic insert Keramikeinsatz Encaje cermico
3 829557 1 Rondella Rondelle Washer U.Scheibe Arandela
4 82658R 1 Filtro olio Filtre huile Oil filter lfilter Filtro de aceite
5 82580R 1 Sensore pressione Capteur pression Oil pressure sensor ldrucksensor Sensor presion de

olio huile aceite
6 411311 1 Tappo conico Bouchon conique Conical plug Konischer Verschlu Tapa conica
7 825665 1 Tappo olio Bouchon huile Oil plug leinfllschraube Tapn aceite
8 479986 1 Guarnizione tappo Joint bouchon Packing for cap Deckeldichtung Junta tapn
9 841150 1 Guarnizione Joint Packing Dichtung Junta
10 828394 1 Albero pompa acqua Arbre de pompe a Coolant pump shaft Wasserpumpenwelle Eje bomba de agua
eau
11 833717 1 Coperchio pompa Couvercle pompe Pump cover Pumpendeckel Tapa bomba
12 259151 6 Vite Vis Screw Schraube Tornillo
13 827884 1 Guarnizione Joint Packing Dichtung Junta
14 841101 1 Tubo Tuyau Tube Schlauch Tubo
15 486075 1 Rondella Rondelle Washer U.Scheibe Arandela
16 CM001917 2 Fascetta Collier Clamp Schelle Abrazadera
17 840826 1 Tubo acqua Tuyau de leau Water pipe Khlflssigkeitsleitung Tubo agua
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
40
T. 13
COPERCHIO VOLANO - FILTRO OLIO
CARTER VOLANT - FILTRE HUILE
FLYWHEEL COVER - OIL FILTER
SCHWUNGRADDECKEL - LFILTER
TAPA VOLANTE - FILTRO DE ACEITE
18 834484 1 Termostato acqua Thermostat de leau Water thermostat Thermostat Termostato agua
Khlflssigkeit
19 840062 1 Staffa Support Bracket Halterung Soporte
20 CM001904 1 Fascetta Collier Clamp Schelle Abrazadera
21 829047 1 Tubo sfiato Tuyau rniflard Breather tube Entlftungsleitung Tubo respiradero
22 015715 1 Vite Vis Screw Schraube Tornillo
23 237553 1 O-ring O-Ring O-Ring O-Ring Anillo OR
24 829486 1 Molla valvola Ressort soupape Oil pressure Feder ldruckventil Muelle vlvula
pressione olio pression dhuile valve spring presion aceite
25 829661 1 Valvola bypass Soupape bypass Bypass valve Schlauchventil Vlvula bypass
26 825051 1 Supporto lamelle Support lamelles Reeds bracket Einlassmembran Soporte lamin.
27 828930 1 Paratia Panneau Panel Wand Panel
28 433800 2 Vite Vis Screw Schraube Tornillo
29 827929 1 Girante pompa Roue de pompe Rotor Wasserpumpenrad Rotor de la bomba
30 485084 1 Anello tenuta Bague dtanchite Oil seal Dichtring Reten de ac.
31 414838 8 Vite Vis Screw Schraube Tornillo
32 414837 2 Vite Vis Screw Schraube Tornillo
33 8290405 1 Tappo Bouchon Plug Verschlu Tapn
34 479986 1 Guarnizione tappo Joint bouchon Packing for cap Deckeldichtung Junta tapn
35 583584 1 Piastrina Plaquette Plate Plttchen Placa
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
41
COPERCHIO VOLANO - FILTRO OLIO
CARTER VOLANT - FILTRE HUILE
FLYWHEEL COVER - OIL FILTER
SCHWUNGRADDECKEL - LFILTER
TAPA VOLANTE - FILTRO DE ACEITE
T. 13
36 289731 1 Vite Vis Screw Schraube Tornillo
37 478895 1 Vite Vis Screw Schraube Tornillo
38 583973 1 Tampone Silentbloc Buffer Puffer Silent-block
39 829254 1 Tubo Tuyau Tube Schlauch Tubo
40 CM001907 1 Fascetta Collier Clamp Schelle Abrazadera
41 841102 1 Tubo acqua Tuyau de leau Water pipe Khlflssigkeitsleitung Tubo agua
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
42
T. 14
COPERCHIO RIDUTTORE
COUVERCLE RDUCTEUR
REDUCTION UNIT COVER
DECKEL UNTERSETZUNGSGETRIEBE
TAPA REDUCTOR
1 8320525 1 Coperchio riduttore Couvercle rducteur Reduction unit cover Deckel Tapa reductor
Untersetzungsgetriebe
2 828115 1 Guarnizione Joint couvercle Cover gasket Dichtung Deckel Junta tapa
coperchio
3 8324875 1 Albero rinvio Arbre de renvoi Countershaft Vorgelegezahnrad Eje de reenvio
4 8342335 1 Albero puleggia Arbre poulie Driven pulley shaft Welle gefhrte Eje polea
condotta entrane Scheibe conducida
5 834770 1 Asse ruota Axe roue Wheel axle Radachse Eje rueda
6 829206 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
7 830198 4 Vite Vis Screw Schraube Tornillo
8 82660R 1 Cuscinetto Roulement Bearing Lager Cojinete
9 829201 1 Anello tenuta Bague dtanchite Oil seal Dichtring Reten de ac.
10 82659R 1 Cuscinetto Roulement Bearing Lager Cojinete
11 840733 1 Sfiato Purge Breather pipe Entlftung Ventilacion
12 487948 1 Fascetta Collier Clamp Schelle Abrazadera
13 485703 1 Guarnizione Joint Packing Dichtung Junta
14 269755 1 Vite Vis Screw Schraube Tornillo
15 828911 3 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
43
T. 15
RACCORDO AMMISSIONE - CORPO FARFALLATO - INIETTORE
RACCORD DADMISSION - CORPS PAPILLON - INJECTEUR
UNION PIPE - THROTTLE BODY - INJECTOR
ANSAUGSTUTZEN - DROSSELKLAPPENGEHUSE - EINSPRITZDSE
RACORD ADMISIN - CUERPO CON MARIPOSA - INYECTOR
1 834401 1 Raccordo ammiss. Raccord dadmiss. Union pipe Ansaugstutzen Racord admisin
2 8304275 1 Iniettore Injecteur avec Injector with Einspritzdse mit Inyector con
support bracket Halter soporte
3 830061 1 Vite Vis Screw Schraube Tornillo
4 289731 3 Vite Vis Screw Schraube Tornillo
5 414837 3 Vite Vis Screw Schraube Tornillo
6 826000 1 Corpo farfallato Corps papillon Throttle body Drosselklappen- Cuerpo con
-gehuse mariposa
7 253293 1 Fascetta Collier Clamp Schlauchschelle Abrazadera
8 256856 1 Fascetta Collier Clamp Schlauchschelle Abrazadera
9 828338 1 Manicotto di Manchon admission Intake sleeve Ansaugmuffe Manguito de
aspirazione aspiracion
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
44
T. 16
MARMITTA
SILENCIEUX
SILENCER
AUSPUFFTOPF
SILENCIADOR
1 599208 3 Vite Vis Screw Schraube Tornillo
2 840569 3 Rondella Rondelle Washer U.Scheibe Arandela
3 833910 1 Protezione Protection Guard Schutz Proteccion
4 834951 3 Rondella Rondelle Washer U.Scheibe Arandela
5 834040 3 Tampone Silentbloc Buffer Puffer Silent-block
6 834039 3 Rondella Rondelle Washer U.Scheibe Arandela
7 015341 2 Dado Ecrou Nut Mutter Tuerca
8 834038 3 Vite Vis Screw Schraube Tornillo
9 8439945 1 Marmitta compl. Pot dechappement Muffler, assy. Auspufftopf kpl. Silenciador
complet completo
10 834643 3 Rondella Rondelle Washer U.Scheibe Arandela
11 834041 3 Distanziale Entretoise Spacer Distanzstck Distanciador
12 828194 1 Guarnizione Joint pot Head/muffler Dichtung Junta escape/
marmitta/testa dchappement gasket Auspuff/ Zylinderkopf culata
13 828185 1 Boccola Moyeu Bush Buchse Buje
14 830298 1 Rondella Rondelle Washer U.Scheibe Arandela
15 833417 1 Tappo a vite Bouchon vis Screw plug Schraubverschlu Tapa roscada
16 840370 1 Fascetta Collier Clamp Schlauchschelle Abrazadera
17 834046 1 Protezione Protection Guard Schutz Proteccion
18 833569 3 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
45
T. 16
MARMITTA
SILENCIEUX
SILENCER
AUSPUFFTOPF
SILENCIADOR
19 832446 1 Collettore scarico Collecteur Exhaust manifold Abgaskrmmer Colector escape
Echappement
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
46
T. 17
FILTRO ARIA
FILTRE AIR
AIR FILTER
LUFTFILTER
FILTRO DE AIRE
1 840172 1 Depuratore aria Filtre a air compl. Air cleaner, assy. Luftfilter, kompl. Depurador aire
compl. compl.
2 487845 1 Filtro aria Filtre air Air filter Luftfilter Filtro de aire
3 828399 1 Guarnizione filtro Joint du filtre Packing Filterdichtung Junta
4 258146 6 Vite Vis Screw Schraube Tornillo
5 257301 3 Tampone Silentbloc Buffer Puffer Silent-block
6 271891 3 Vite Vis Screw Schraube Tornillo
7 031092 3 Rondella Rondelle Washer U.Scheibe Arandela
8 254485 2 Piastrina Plaquette Plate Plttchen Placa
9 257302 3 Distanziale Entretoise Spacer Distanzstck Distanciador
10 828341 1 Manicotto di Manchon admission Intake sleeve Ansaugmuffe Manguito de
aspirazione aspiracion
11 CM002910 1 Fascetta Collier Clamp Schelle Abrazadera
12 829006 1 Condotto Canalisation Pipe Ansaugleitung Conducto
13 479132 2 Pomello Bouton Knob Drehknopf Pomo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
47
T. 18
TELAIO
CHASSIS
CHASIS
RAHMEN
CHASIS
1 6209295 1 Telaio Chssis Frame Fahrgestell Chasis
2 6210465 1 Telaietto Chssis Frame Kleiner Rahmen Chasis
3 030059 2 Vite Vis Screw Schraube Tornillo
4 013950 4 Rondella Rondelle Washer U.Scheibe Arandela
5 016406 12 Rondella Rondelle Washer U.Scheibe Arandela
6 020106 2 Dado Ecrou Nut Mutter Tuerca
7 CM0102034 1 SX Traversa Traverse Cross piece Traverse Travesao
8 031117 2 Vite Vis Screw Schraube Tornillo
9 CM0102024 1 DX Traversa Traverse Cross piece Traverse Travesao
10 030059 2 Vite Vis Screw Schraube Tornillo
11 5755444 1 Telaietto Chssis Frame Kleiner Rahmen Chasis
12 020108 2 Dado Ecrou Nut Mutter Tuerca
13 016408 4 Rondella Rondelle Washer U.Scheibe Arandela
14 031119 2 Vite Vis Screw Schraube Tornillo
15 575357 1 Supporto Support Bracket Halter Soporte
16 003038 2 Rondella Rondelle Washer U.Scheibe Arandela
17 6208695 1 Traversa Traverse Cross piece Traverse Travesao
18 031088 8 Vite Vis Screw Schraube Tornillo
19 003056 10 Rondella Rondelle Washer U.Scheibe Arandela
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
48
T. 19
CAVALLETTI
BEQUILLES
CENTRAL STAND
STNDER
CABALLETES
1 232108 1 Dado Ecrou Nut Mutter Tuerca
2 582625 1 Cavalletto laterale Bquille latrale Side stand Seitenstnder Caballete lateral
3 583155 1 Vite fissaggio Vis fix. Sec. screw Schraube Tornillo
4 272426 1 Tampone scontro Bloc darrt Stop buffer Anschlagpuffer Tope goma
5 013880 1 Rondella Rondelle Washer U.Scheibe Arandela
6 031088 1 Vite Vis Screw Schraube Tornillo
7 295789 1 Molla esterna Ressort Spring Feder Muelle
8 295788 1 Molla interna Ressort Spring Feder Muelle
9 191189 2 Guarnizione Joint Packing Dichtung Junta
10 582633 1 Interruttore Interrupteur Switch Schalter Interruptor
11 601059 1 Cavalletto Bquille Central stand Kippstnder Caballete
12 582756 4 Boccola Moyeu Bush Buchse Buje
13 031088 2 Vite Vis Screw Schraube Tornillo
14 232108 4 Dado Ecrou Nut Mutter Tuerca
15 583480 2 Vite Vis Screw Schraube Tornillo
16 031153 4 Vite Vis Screw Schraube Tornillo
17 583162 1 Molla interna Ressort Spring Feder Muelle
18 5990445 1 Piastra Plaque Plate Platte Chapa
19 583161 1 Molla esterna Ressort Spring Feder Muelle
20 031119 1 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
49
T. 19
CAVALLETTI
BEQUILLES
CENTRAL STAND
STNDER
CABALLETES
21 296748 1 Rondella Rondelle Washer U.Scheibe Arandela
22 582700 2 Anello Circlips Ring Ring Anillo
23 582699 2 Boccola Moyeu Bush Buchse Buje
24 582893 2 Tappo Bouchon Plug Verschlu Tapn
25 235661 1 Guarnizione Joint Packing Dichtung Junta
26 109960 1 Fascetta Collier Clamp Schelle Abrazadera
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
50
T. 20
IMPIANTO RAFFERDDAMENTO
CIRCUIT DE REFROIDISSEMENT
COOLING SYSTEM
KHLANLAGE
INSTALACIN DE REFRIGERACIN
1 573454 1 Tappo serbatoio Bouchon de rserv. Filler cap Tankverschluss Tapn depsito
2 620737 1 Guarnizione Joint Packing Dichtung Junta
3 575541 1 Serbatoio Rservoir Tank Tank Deposito
4 CM001903 3 Fascetta Collier Clamp Schelle Abrazadera
5 CM001904 1 Fascetta Collier Clamp Schelle Abrazadera
6 620105 1 Staffa Support Bracket Halterung Soporte
7 CM001915 3 Fascetta Collier Clamp Schelle Abrazadera
8 270793 2 Vite Vis Screw Schraube Tornillo
9 576766 1 Tubo Tuyau Tube Schlauch Tubo
10 351782 2 Tampone Silentbloc Buffer Puffer Silent-block
11 575540 1 Tubo Tuyau Tube Schlauch Tubo
12 273288 2 Distanziale Entretoise Spacer Distanzstck Distanciador
13 013092 2 Rondella Rondelle Washer U.Scheibe Arandela
14 271891 2 Vite Vis Screw Schraube Tornillo
15 620779 1 Tubo Tuyau Tube Schlauch Tubo
16 258904 4 Tampone Silentbloc Buffer Puffer Silent-block
17 620220 1 Tubo Tuyau Tube Schlauch Tubo
18 57311R 1 Radiatore Radiateur Cooler Khler Radiador
19 621030 1 Elettroventilatore Electroventilateur Electric fan Ventilator Electro ventilador
20 254485 3 Piastrina Plaquette Plate Plttchen Placa
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
51
T. 20
IMPIANTO RAFFERDDAMENTO
CIRCUIT DE REFROIDISSEMENT
COOLING SYSTEM
KHLANLAGE
INSTALACIN DE REFRIGERACIN
21 620871 1 Tubo Tuyau Tube Schlauch Tubo
22 272836 3 Vite Vis Screw Schraube Tornillo
23 576301 1 Supporto Support Bracket Halter Soporte
24 268596 3 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
52
T. 21
SERBATOIO CARBURANTE
RESERVOIR CARBURANT
FUEL TANK
KRAFTSTOFFTANK
DEPSITO CARBURANTE
1 576544 1 Serbatoio Reservoir Fuel tank Kraftstofftank Depsito
carburante carburant carburante
2 577790 1 Protezione Protection Heat guard Hitzeschutz Proteccion
paracalore pare-chaleur paracalor
3 259832 1 Tappo serbatoio Bouchon de rserv. Filler cap Tankverschluss Tapn depsito
4 258160 1 Guarnizione Joint Packing Dichtung Junta
5 254485 1 Piastrina Plaquette Plate Plttchen Placa
6 CM011901 1 Tubo sfiato Tuyau dvent Tank breather pipe Tankentlftungsleitung Tubo ventilacin
serbatoio du rservoir depsito
7 575873 1 Vaschetta Cuvette Float ch. Schwimmergehuse Cuba
8 031091 2 Vite Vis Screw Schraube Tornillo
9 270216 2 Rondella Rondelle Washer U.Scheibe Arandela
10 195482 1 Dado Ecrou Nut Mutter Tuerca
11 078307 1 Rondella Rondelle Washer U.Scheibe Arandela
12 463195 1 Tampone Silentbloc Buffer Puffer Silent-block
13 575304 1 Inserto Pice Insert Insatz Encaje
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
53
1 576468 1 Canister Canister Canister Canister Canister
2 CM007504 1 Tubo Tuyau Tube Schlauch Tubo
3 576860 4 Tubo Tuyau Tube Schlauch Tubo
4 CM002912 1 Fascetta Collier Clamp Schelle Abrazadera
5 CM001914 7 Fascetta Collier Clamp Schelle Abrazadera
6 622375 1 Valvola sicurezza Volet Valve Ventil Vlvula
7 145298 3 Fascetta Collier Clamp Schelle Abrazadera
8 CM007515 1 Tubo Tuyau Tube Schlauch Tubo
9 576454 1 Supporto elastico Support last. Spring support Elastischer Halter Soporte elstico
10 622376 1 Valvola roll-over Volet Valve Ventil Vlvula
11 620106 1 Staffa attacco Support Bracket Halterung Soporte
canister
12 090854 1 Cinghietta Collier Clamp Schelle Abrazadera
13 CM001914 2 Fascetta Collier Clamp Schelle Abrazadera
14 219277 1 Dado Ecrou Nut Mutter Tuerca
15 031088 1 Vite Vis Screw Schraube Tornillo
16 003056 1 Rondella Rondelle Washer U.Scheibe Arandela
17 CM007515 1 Tubo Tuyau Tube Schlauch Tubo
18 CM007503 1 Tubo Tuyau Tube Schlauch Tubo
T. 22
CANISTER
CANISTER
CANISTER
CANISTER
CANISTER
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
54
T. 23
IMPIANTO ALIMENTAZIONE
CIRCUIT D'ALIMENTATION
SUPPLY SYSTEM
KRAFTSTOFFANLANGE
INSTALLACION DE ALIMENTACION
1 621617 1 Tubo mandata Tuyau dalimentation Injection pipe Kraftstoffdruck- Tubo envo
-schlauch
2 621616 1 Tubo ritorno Tuyau de Return pipe Kraftstoffrckleitung Tubo retorno
refoulement
3 015715 1 Vite Vis Screw Schraube Tornillo
4 012528 1 Rondella Rondelle Washer Federring Arandela
5 273779 2 Fascetta Collier Clamp Schelle Abrazadera
6 145298 2 Fascetta Collier Clamp Schelle Abrazadera
7 576688 1 Pompa Pompe alimentation Fuel pump Kraftstoffpumpe Bomba de
alimentazione alimentacin
8 576546 1 Ghiera Douille Ring nut Gewindering Casquillo
9 576542 1 Guarnizione Joint Packing Dichtung Junta
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
69
T. 32
FORCELLA
FOURCHE
FORK
GABEL
HORQUILLA
1 5982615 1 Gr. ralle Gr. But. Dir. Steering bearing Lagerschale Gr. Coj. De dir.
assy.
2 601118 1 Forcella Fourche Fork Gabel Horquilla
3 011109 1 Ghiera Douille Ring nut Gewindering Casquillo
4 582787 1 Rondella Rondelle Washer U.Scheibe Arandela
5 599499 1 Piastra Plaque Plate Platte Chapa
6 599549 1 SX Fodero Protection Sleeve Schutzstuck Proteccin
6 599550 1 DX Fodero Protection Sleeve Schutzstuck Proteccin
7 599511 4 Vite Vis Screw Schraube Tornillo
8 599512 2 Vite Vis Screw Schraube Tornillo
9 599513 2 Vite Vis Screw Schraube Tornillo
10 599504 2 Rondella Rondelle Washer U.Scheibe Arandela
11 599510 4 Rondella Rondelle Washer U.Scheibe Arandela
12 599572 2 Rondella Rondelle Washer U.Scheibe Arandela
13 599501 2 Paraolio Pare-huile Oil seal Dichtring Sello de lub.
14 599509 2 Tampone Silentbloc Buffer Puffer Silent-block
15 599503 2 Anello ritegno Circlips Circlip Sprengring Anillo elastico
16 599502 2 Parapolvere Pare-poussire Dust cover Staubdeckel Guardapolvo
17 599505 2 Boccola Moyeu Bush Buchse Buje
18 599629 2 Boccola Moyeu Bush Buchse Buje
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
70
T. 32
FORCELLA
FOURCHE
FORK
GABEL
HORQUILLA
19 601166 2 Stelo Tige Stem Stange Varilla
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
71
T. 33
BRACCIO OSCILLANTE
BRAS OSCILLANT
SWINGING ARM
SCHWINGARM
BRAZO OSCILANTE
1 598076 1 Braccio oscillante Bras oscillant Swinging arm Schwingarm Brazo oscilante
2 597839 1 Distanziale Entretoise Spacer Distanzstck Distanciador
3 597844 1 Cuscinetto Roulement Bearing Lager Cojinete
4 006635 1 Anello elastico Circlips Circlip Sprengring Anillo elastico
5 600161 1 Boccola a rullini Cage Aiguille Roller cage Rollenkfig Jaula rodillos
6 232108 1 Dado Ecrou Nut Mutter Tuerca
7 179326 1 Rondella Rondelle Washer U.Scheibe Arandela
8 178149 2 Tampone inf. Silentbloc inf. Lower buffer Puffer u. Silent-block inf.
9 261319 1 Dado Ecrou Nut Mutter Tuerca
10 227199 1 Rondella Rondelle Washer U.Scheibe Arandela
11 564611 1 Dado Ecrou Nut Mutter Tuerca
12 597836 1 Asse Essieu Shaft Achse Eje
13 597833 1 Distanziale Entretoise Spacer Distanzstck Distanciador
14 261319 1 Dado Ecrou Nut Mutter Tuerca
15 013962 2 Rondella Rondelle Washer U.Scheibe Arandela
16 598068 1 Tirante compl. Tirant Tie rod Zugstange Tirante
17 597262 1 Tampone Silentbloc Buffer Puffer Silent-block
18 597837 1 Scodellino Rondelle dar Stop washer Federaufnahme Platillo
19 842602 1 Dado Ecrou Nut Mutter Tuerca
20 597838 1 Asse Essieu Shaft Achse Eje
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
72
T. 33
BRACCIO OSCILLANTE
BRAS OSCILLANT
SWINGING ARM
SCHWINGARM
BRAZO OSCILANTE
21 709037 1 Rondella Rondelle Washer U.Scheibe Arandela
22 597868 1 Rondella Rondelle Washer U.Scheibe Arandela
23 5767574 1 Staffa Support Bracket Halterung Soporte
24 031153 2 Vite Vis Screw Schraube Tornillo
25 709646 2 Rondella Rondelle Washer U.Scheibe Arandela
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
73
T. 34
AMMORTIZZATORI
AMORTISSEUS
DAMPERS
STODMPFER
AMORTIGUADORES
1 598930 2 Ammortizzatore Amortisseur Damper Stodmpfer Amortiguador
2 597178 1 Distanziale Entretoise Spacer Distanzstck Distanciador
3 597179 1 Distanziale Entretoise Spacer Distanzstck Distanciador
4 599564 2 Vite Vis Screw Schraube Tornillo
5 232108 4 Dado Ecrou Nut Mutter Tuerca
6 599559 2 Staffa Support Bracket Halterung Soporte
7 844483 4 Vite Vis Screw Schraube Tornillo
8 020008 4 Dado Ecrou Nut Mutter Tuerca
9 268158 2 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
77
T. 38
MANUBRIO - POMPE FRENO
GUIDON - POMPE DU FREIN
HANDLEBAR - BRAKE PUMP
LENKSTANGE - BREMSPUMPEN
MANILLAR - BOMBAS DEL FRENO
1 271453 1 DX Manopola Poigne Grip Handgriff Puo
1 271452 1 SX Manopola Poigne Grip Handgriff Puo
2 582767 1 Trasmissione Transmission Transmiss. Bowdenzg Transmisin
3 582768 1 Trasmissione Transmission Transmiss. Bowdenzg Transmisin
4 271434 2 Vite Vis Screw Schraube Tornillo
5 582034 2 Terminale Embout Nipple Nippel Terminal
6 598351 1 Manicotto Manchon Sleeve Muffe Manguito
7 CM072602 1 DX Pompa freno Matre cylindre Master cil. Hauptbremszylinder Bomba freno
7 CM072601 1 SX Pompa freno Matre cylindre Master cil. Hauptbremszylinder Bomba freno
8 015330 1 Dado Ecrou Nut Mutter Tuerca
9 012543 1 Rondella Rondelle Washer U.Scheibe Arandela
10 178790 1 Rondella Rondelle Washer U.Scheibe Arandela
11 223605 1 Vite Vis Screw Schraube Tornillo
12 583575 2 Interruttore stop Interrupteur stop Stop switch Stopschalter Interruptor stop
13 5818804 1 Manubrio Guidon Handlebars Lenker Manillar
14 497031 2 Leva freno Levier du frein Brake lever Bremshebel Palanca de freno
15 497032 2 Tappo Bouchon Plug Verschlu Tapn
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
78
T. 39
TUBAZIONI FRENO - PINZE FRENO
CANALISATION D'HUILE - PINCES FREIN
BRAKE PIPES - BRAKE CALIPERS
BREMSLEITUNGEN - BREMSZANGEN
TUBERAS DEL FRENO - PINZAS DEL FRENO
1 CM072502 1 DX-ANTPinza freno Etrier de frein Caliper Bremszange Pinza del freno
1 CM072501 1 SX-ANTPinza freno Etrier de frein Caliper Bremszange Pinza del freno
2 56167R 1 POST Pinza freno Etrier de frein Caliper Bremszange Pinza del freno
3 497394 1 POST Kit pasticche freno Jeu plaquettes freins Brake pads kit Bremskltze Juego pastillas
freno
4 015792 4 Vite Vis Screw Schraube Tornillo
5 709047 4 Rondella Rondelle Washer U.Scheibe Arandela
6 497396 2 ANT Kit pasticche freno Jeu plaquettes freins Brake pads kit Bremskltze Juego pastillas
freno
7 709047 2 Rondella Rondelle Washer U.Scheibe Arandela
8 844483 2 Vite Vis Screw Schraube Tornillo
9 598919 2 Vite Vis Screw Schraube Tornillo
10 709047 2 Rondella Rondelle Washer U.Scheibe Arandela
11 598060 1 Piastra Plaque Plate Platte Chapa
12 265451 7 Vite Vis Screw Schraube Tornillo
13 006966 5 Rondella Rondelle Washer Federring Arandela
14 812592 2 Vite Vis Screw Schraube Tornillo
15 414838 2 Vite Vis Screw Schraube Tornillo
16 031086 1 Vite Vis Screw Schraube Tornillo
17 597395 1 Fascetta Collier Clamp Schelle Abrazadera
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
79
T. 39
TUBAZIONI FRENO - PINZE FRENO
CANALISATIOND'HUILE - PINCES FREIN
BRAKE PIPES - BRAKE CALIPERS
BREMSLEITUNGEN - BREMSZANGEN
TUBERAS DEL FRENO - PINZAS DEL FRENO
18 127927 15 Guarnizione (CU) Joint (CU) Packing (CU) Dichtung (CU) Junta (CU)
19 288245 2 Dado Ecrou Nut Mutter Tuerca
20 274350 2 Passacavo Passe-cble Grommet Kabeldurchgang Pasacables
21 122675 2 Vite Vis Screw Schraube Tornillo
22 600876 1 Tubazione freno Conduite frein Brake pipe Bremsleitung Tubera freno
23 599545 1 Tubazione freno Conduite frein Brake pipe Bremsleitung Tubera freno
24 599514 1 Tubazione freno Conduite frein Brake pipe Bremsleitung Tubera freno
25 564784 1 Tubazione freno Conduite frein Brake pipe Bremsleitung Tubera freno
26 599515 1 Tubazione freno Conduite frein Brake pipe Bremsleitung Tubera freno
27 482290 2 Fascetta Collier Clamp Schelle Abrazadera
28 56122R 1 Valvola Soupape Valve Ventil Vlvula
29 597033 1 Raccordo Raccord Joint.p. Stutzen Racor
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
83
T. 43
DISPOSITIVI ELETTRICI-BATTERIA
DISPOSITIFS ELECTRIQUES-BATTERIE
ELECTRICAL DEVICES-BATTERY
ELEKTRISCHE AUSRSTUNG-BATTERIE
DISPOSITIVOS ELCTRICOS-BATERA
1 015759 2 Vite Vis Screw Schraube Tornillo
2 013880 2 Rondella Rondelle Washer U.Scheibe Arandela
3 016406 2 Rondella Rondelle Washer U.Scheibe Arandela
4 829121 1 Decoder Dcodeur Decoder Decoder Decodificador
5 090854 1 Cinghietta Courroie Strip Riemen Correa
6 638733 1 Batteria Batterie Battery Batterie Bateria
7 496404 1 30A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
8 015759 1 Vite Vis Screw Schraube Tornillo
9 016405 2 Rondella Rondelle Washer U.Scheibe Arandela
10 577313 3 Tampone Silentbloc Buffer Puffer Silent-block
11 582690 1 12V-150A Teleruttore Relais Rem. control switch Fernschalter Telerruptor
12 583529 1 Dispositivo Dispositif Device Vorrichtung Dispositivo
13 583283 1 Guarnizione Joint Gasket Dichtung Empaque
14 638635 1 Centralina Centrale Electronic control Elektronisches Centralita
elettronica unit (ECU) Steuergert electrnica
15 581859 1 Staffa Support Bracket Halterung Soporte
16 080341 1 MT Cavo A.T. Cble H.T. H.T. cable Zundkabel Cable A.T.
17 293845 1 Cappuccio Anti - Parasite Screened cap Zndkerzenstecker Capuchon blindado
schermato
18 436919 1 Collare Collier Clamp Schelle Abrazadera
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
84
T. 43
DISPOSITIVI ELETTRICI-BATTERIA
DISPOSITIFS ELECTRIQUES-BATTERIE
ELECTRICAL DEVICES-BATTERY
ELEKTRISCHE AUSRSTUNG-BATTERIE
DISPOSITIVOS ELCTRICOS-BATERA
19 582906 1 Supporto Support Bracket Halter Soporte
20 828817 1 Bobina A.T. Bobine H.T. H.T. coil Zndspule Bobina A.T.
21 584646 1 Staffa Support Bracket Halterung Soporte
22 071671 1 Cappuccio Cache Cap Kappe Capuchn
23 020003 4 Dado Ecrou Nut Mutter Tuerca
24 583236 4 Vite Vis Screw Schraube Tornillo
25 012554 4 Rondella Rondelle Washer U.Scheibe Arandela
26 434541 1 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
85
T. 44
DISPOSITIVI ELETTRICI
DISPOSITIFS ELECTRIQUES-BATTERIE
ELECTRICAL DEVICES-BATTERY
ELEKTRISCHE AUSRSTUNG-BATTERIE
DISPOSITIVOS ELCTRICOS-BATERA
1 584533 1 Regolatore di Regulateur de tesion Voltage regualtor Spannungsregler Regulador de
tensione tension
2 828863 2 Vite Vis Screw Schraube Tornillo
3 584739 1 Centralina iniezione Dispositif lectron. Electronic injection Elektron. einspritzung Dispositivo electr.
elettr. dinjection device -vorrichtung de la inyeccin
4 582141 1 Staffa Support Bracket Halterung Soporte
5 58002R 4 12V-30A Teleruttore Relais Rem. control switch Fernschalter Telerruptor
6 015597 2 Vite Vis Screw Schraube Tornillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
86
T. 45
GRUPPO CAVETTI PRINCIPALE
GROUPE PRINCIPAL DES CBLES
MAIN CABLES UNIT
HAUPTLIZENAGGREGAT
GRUPO CABLES PRINCIPAL
1 584969 1 Gr. cavetti Faisceau de cbles Cable harness Kabelbaum Gr. de cables
2 583282 2 Protezione Protection Guard Schutz Proteccion
3 582930 1 3A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
3 293256 1 5A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
3 292507 1 10A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
3 290860 1 15A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
3 252945 4 7,5A Fusibile lamellare Fusible lamellaire Reed fuse Lamellensicherung Fusible de lminas
4 582650 1 Gr. cavetti Faisceau de cbles Cable harness Kabelbaum Gr. de cables
5 583282 2 Protezione Protection Guard Schutz Proteccion
6 581191 1 Coperchio Couvercle Cover Deckel Tapa
7 018644 1 Vite Vis Screw Schraube Tornillo
8 016404 1 Rondella Rondelle Washer U.Scheibe Arandela
9 581190 1 Portafusibile Porte fus. Fuse holder Sicherungshalter Porta fusible
10 580653 1 Portafusibile Porte fus. Fuse holder Sicherungshalter Porta fusible
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
87
T. 46
SERRATURE
SERRURES
LOCKS
SCHLIEVORRICHTUNG
CERRADURAS
1 582951 1 Commutatore a Commutateur clef Key operated switch Zndschalter Conmutador de
chiave llave
2 253937 1 Molletta arresto Ressort darrt Spring Drahtspannfeder Muelle parada
3 577816 1 Blocchetto Bloc Block Schloriegel Bloque
4 298581 1 Corpo serratura Corps serrure Lock body Schloaufnahme Cuerpo cerradura
5 575810 1 Sbozzato Clef blanch Key blank Schlsselrohling Llave semiacabada
6 576552 1 Cilindretto Cylindre Cylinder Bremszylinder Cilindro
7 298731 1 Anello di tenuta Joint spie Oil seal Dichtring Retn de aceite
8 298838 1 Molla Ressort Spring Feder Muelle
9 298594 1 Rondella Rondelle Washer U.Scheibe Arandela
10 828800 1 Antenna Antenne Antenna Antenne Antena
11 577194 1 Staffa Support Bracket Halterung Soporte
12 582990 1 Attuatore Actionneur Actuator Stellglied Accionador
13 620415 1 Molla Ressort Spring Feder Muelle
14 577131 1 Molla Ressort Spring Feder Muelle
15 299972 1 Vite Vis Screw Schraube Tornillo
16 584121 2 Vite Vis Screw Schraube Tornillo
17 577620 3 Dado Ecrou Nut Mutter Tuerca
18 577128 1 Giunto Joint Connecting joint Verbindung Racord
19 577129 1 Leva Levier Lever Hebel Palanca
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
88
T. 46
SERRATURE
SERRURES
LOCKS
SCHLIEVORRICHTUNG
CERRADURAS
20 CM012805 1 Trasmissione Transmission Transmiss. Bowdenzg Transmisin
21 CM012809 1 Trasmissione Transmission Transmiss. Bowdenzg Transmisin
22 CM023704 1 Serratura sella Serrure selle Saddle lock Sitzbankschlo Cerradura silln
23 259348 2 Vite Vis Screw Schraube Tornillo
24 145298 3 Fascetta Collier Clamp Schelle Abrazadera
25 638834 1 Centralina Centrale Electronic control Elektronisches Centralita
elettronica unit (ECU) Steuergert electrnica
26 638835 1 Telecomando Telecommande Remote control Ferbedienung Control remoto
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
89
T. 47
RUOTA ANTERIORE
ROUE AV.
FRONT WHEEL
VORDERRAD
RUEDA DELANTERA
1 271740 1 Dado Ecrou Nut Mutter Tuerca
2 564446 1 Asse ruota Axe roue Wheel axle Radachse Eje rueda
3 58014R 1 Ruota fonica Codeur Encoder Encoder Tonrad Encoder
4 145298 2 Fascetta Collier Clamp Schelle Abrazadera
5 271147 10 Vite Vis Screw Schraube Tornillo
6 560136 1 Passacavo Passe-cble Grommet Kabeldurchgang Pasacables
7 599315 2 Disco freno Disque frein Brake plate Bremscheibe Disco freno
8 327187 2 Cuscinetto Roulement Bearing Lager Cojinete
9 564447 1 Distanziale Entretoise Spacer Distanzstck Distanciador
10 564491 1 Cuscinetto Roulement Bearing Lager Cojinete
11 564448 1 Distanziale Entretoise Spacer Distanzstck Distanciador
12 597519T 1 Ruota Roue Wheel Rad Rueda
13 597679 1 Valvola Volet de gaz Valve Ventil Vlvula gas
14 597339 1 MIC Pneumatico Pneu Tyre Reifen Neumtico
14 597340 1 PIR Pneumatico Pneu Tyre Reifen Neumtico
15 564489 1 Scodellino Rondelle dar Stop washer Federaufnahme Platillo
Downloaded from www.Manualslib.com manuals search engine
ZAPM 270W
Pos.
Pos.
Loc.
Pos.
Pos.
Numero
Numro
Number
Nummer
Nmero
Q.t
Q.t
Q.ty
M.ge
Cant.
Nota
Note
Nota
Anm.
Nota
Denominazione Dsignation Description Beschreibung Descripcin
90
T. 48
RUOTA POSTERIORE
ROUE AR.
REAR WHEEL
HINTERRAD
RUEDA TRASERA
1 598022 1 Ruota Roue Wheel Rad Rueda
2 597565 5 Dado Ecrou Nut Mutter Tuerca
3 012789 1 Coppiglia Goupille Split pin Splint Grupilla
4 825758 5 Vite Vis Screw Schraube Tornillo
5 709047 5 Rondella Rondelle Washer U.Scheibe Arandela
6 246976 5 Rondella Rondelle Washer U.Scheibe Arandela
7 599582 1 MIC Pneumatico Pneu Tyre Reifen Neumtico
7 599065 1 PIR Pneumatico Pneu Tyre Reifen Neumtico
8 841030 1 Braccio sosp. Bras. de la susp. Suspension arm Schwingarm Brazo suspensin
9 597565 5 Dado Ecrou Nut Mutter Tuerca
10 597564 5 Vite Vis Screw Schraube Tornillo
11 597520 1 Disco freno Disque frein Brake plate Bremscheibe Disco freno
12 597528 1 Distanziale Entretoise Spacer Distanzstck Distanciador
13 597679 1 Valvola Volet de gaz Valve Ventil Vlvula gas
14 598070 1 Tamburo Tambour Drum Trommel Tambor
15 826974 1 Cuscinetto Roulement Bearing Lager Cojinete
16 597390 1 Distanziale Entretoise Spacer Distanzstck Distanciador
17 563728 1 Dado Ecrou Nut Mutter Tuerca
18 194423 1 Cappellotto Cache Cap Kappe Capuchn
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine