Scribd
Upload
94 views

Configurar Troncal

The document provides instructions for configuring trunking between a Cisco Catalyst switch and a 3Com SuperStack switch. It outlines creating two VLANs on each switch, VLAN 100 for workstations and VLAN 200 for servers. It then describes configuring port fastEthernet 0/1 on the Cisco switch and port GigabitEthernet 1/0/1 on the 3Com switch as 802.1q trunk ports. Finally, it assigns ports fastEthernet 0/5 on the Cisco switch to VLAN 100 and port fastEthernet 0/10 to VLAN 200 for connectivity.

Uploaded by

neza2610
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
94 views

Configurar Troncal

The document provides instructions for configuring trunking between a Cisco Catalyst switch and a 3Com SuperStack switch. It outlines creating two VLANs on each switch, VLAN 100 for workstations and VLAN 200 for servers. It then describes configuring port fastEthernet 0/1 on the Cisco switch and port GigabitEthernet 1/0/1 on the 3Com switch as 802.1q trunk ports. Finally, it assigns ports fastEthernet 0/5 on the Cisco switch to VLAN 100 and port fastEthernet 0/10 to VLAN 200 for connectivity.

Uploaded by

neza2610
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

How to configure Trunking between a

Cisco Catalyst and a 3Com


SuperStack?
Yasir IrfanProfile: Yasir Irfan

I am writing this article to answer the question for establishing the trunking between a
Cisco Catalyst Switch and a 3Com Super Stack Switch in ITKE community.

The goal of the article is show the user how to configure an inter operable trunk port in
both Cisco and 3 Com Switch. As far as trunking concepts are concerned I did posted an
article in ITKE blog comparing the HP Procurve and a Cisco Catalyst Switches which help to
understand the trunking methodologies applied in 3 Com and Cisco Switches.
In order understand the configuration process easily I present a scenario, based on this
scenario we will configure the Cisco and 3 Com Switches to meet the objectives.
In this example

A Cisco Catalyst Switch is connected to a 3-Com Super Stack 4200 Switch (3-

Com Super stack 3300 configuration is also available as the configuration process
defers in a 3300 Switch)) using a port fast /Giga Ethernet 1 in both the Switches.

Create two VLANS locally in both the Cisco Catalyst Switch and a 3-Com Super

Stack 4200.

1.

VLAN 100 For Workstations (named PCS).

2.

VLAN 200- For Servers and Management Devices (Named MANG).

Configure fast Ethernet 0/1 on both the Cisco Catalyst Switch and a 3-Com

Super Stack 4200 as 802.1 q trunking port.

Cisco Catalyst Switch Configuration Example

Task 1 Create VLANS


ITKE-Cisco#configure t
Enter configuration commands, one per line. End with CNTL/Z.
ITKE-Cisco(config)#vlan 100
ITKE-Cisco(config-vlan)#name PCS
ITKE-Cisco(config-vlan)#exit
ITKE-Cisco(config)#vlan 200
ITKE-Cisco(config-vlan)#name MANG

Task 2 Configure the port fastethernet 0/1 as 802.1 q trunk port.


ITKE-Cisco(config)#interface fastEthernet 0/1
ITKE-Cisco(config-if)#description Connected to 3-COM Switch
ITKE-Cisco(config-if)#switchport trunk encapsulation dot1q
ITKE-Cisco(config-if)#switchport mode trunk
ITKE-Cisco(config-if)#no shutdown
ITKE-Cisco(config-if)#

Task 3 Configure the ports fastethernet 0/5 for VLAN 100 and fastethernet
0/10 for VLAN 200.
ITKE-Cisco(config)#interface fastEthernet 0/5
ITKE-Cisco(config-if)#description Connected to PC
ITKE-Cisco(config-if)#switchport mode access
ITKE-Cisco(config-if)#switchport access vlan 100

ITKE-Cisco(config)#interface fastEthernet 0/10


ITKE-Cisco(config-if)#description Connected to SERVER
ITKE-Cisco(config-if)#switchport mode access
ITKE-Cisco(config-if)#switchport access vlan 200

3-Com Super Stack 4200 Switch Configuration Example


(Configuration steps are as per the 3-Com Advance configuration
manual not tested).
Task 1 Create VLANS and add ports Giga Ethernet 0/5 for VLAN 100 and
Giga Ethernet 0/10 for VLAN 200
<SwitchB> system-view
[SwitchB] vlan 100
[SwitchB-vlan100] description PCS
[SwitchB-vlan100] port GigabitEthernet 1/0/5
[SwitchB-vlan100] quit
Create VLAN 200, and add GigabitEthernet1/0/10 to VLAN 200.
[SwitchB] vlan 200
[SwitchB-vlan200] description MANG
[SwitchB-vlan200] port GigabitEthernet 1/0/10
[SwitchB-vlan200] quit

Task 2 Configure the port Gigaethernet 1/0/1 as a trunk port.


[SwitchB] interface GigabitEthernet 1/0/1
[SwitchB-GigabitEthernet1/0/1] port link-type trunk

3-Com Super Stack 3300 Switch Configuration Example.


Task 1 Create VLANS
Select menu option (bridge/vlan): create
Select VLAN ID (2-4094)[3]: 100
Enter VLAN Name [VLAN 10]: PCS
Select menu option (bridge/vlan): create
Select VLAN ID (2-4094)[3]: 200
Enter VLAN Name [VLAN 11]: MANG

Task 2 Configure the port fastethernet 0/1 as 802.1 q trunk port


Select VLAN ID (1-2,) [1]: 100 200
Select bridge ports (AL1-AL4,unit:port,?): 1:1
Enter tag type (untagged,tagged): tagged

Task 3 Configure the ports Giga Ethernet 0/5 for VLAN 100 and Giga
Ethernet 0/10 for VLAN 200
Select menu option (bridge/vlan/modify): add
Select VLAN ID (1-2,)[1]: 100
Select bridge ports (AL1-AL4,unit:port,?): 1:5
Enter tag type (untagged, tagged): untagged
Select menu option (bridge/vlan/modify): add
Select VLAN ID (1-2,)[1]: 200
Select bridge ports (AL1-AL4,unit:port,?): 1:10
Enter tag type (untagged, tagged): untagged

You might also like