RDA5802E
SINGLE-CHIP BROADCAST FM RADIO TUNER
1
Rev.1.7Jun.2009
General Description
The RDA5802E (RDA5802 Enhanced) is a
single-chip broadcast FM stereo radio tuner with
fully integrated synthesizer, IF selectivity and MPX
decoder. The tuner uses the CMOS process,
support multi-interface and require the least
external component. The package size is 4X4mm
and is completely adjustment-free. All these make
it very suitable for portable devices.
The RDA5802E has a powerful low-IF digital audio
processor, this make it have optimum sound quality
with varying reception conditions.
The RDA5802E can be tuned to the worldwide
frequency band.
Figure 1-1. RDA5802E Top View
1.1
Features
CMOS single-chip fully-integrated FM tuner
Low power consumption
Total current consumption lower than 22mA at 3.0V
Programmable de-emphasis (50/75 s)
Receive signal strength indicator (RSSI)
power supply
Bass boost
Support worldwide frequency band
Volume control
65 -108 MHz
I2S digital output interface
Digital low-IF tuner
Line-level analog output voltage
Image-reject down-converter
32.768 KHz 12M,24M,13M,26M,19.2M,38.4MHz
High performance A/D converter
IF selectivity performed internally
2-wire and 3-wire serial control bus interface
Fully integrated digital frequency synthesizer
Directly support 32 resistance loading
Fully integrated on-chip RF and IF VCO
Integrated LDO regulator
Fully integrated on-chip loop filter
Autonomous search tuning
Support 32.768KHz crystal oscillator
Digital auto gain control (AGC)
High cut
l
l
Digital adaptive noise cancellation
Mono/stereo switch
Soft mute
Reference clock
l
1.2
1.8 to 5.5 V operation voltage
4X4mm 24 pin QFN package
Applications
Cellular handsets
MP3, MP4 players
Portable radiosPDAs, Notebook
Copyright RDA Microelectronics Inc. 2006. All rights are reserved.
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Table of Contents
General Description.................................................................................................................................... 1
1.1
Features ......................................................................................................................................... 1
1.2
Applications .................................................................................................................................... 1
2
3
Table of Contents ........................................................................................................................................ 2
Functional Description ............................................................................................................................... 3
3.1
FM Receiver ................................................................................................................................. 3
3.2
Synthesizer.................................................................................................................................... 3
3.3
Power Supply................................................................................................................................ 3
3.4
RESET and Control Interface select ............................................................................................. 4
3.5
Control Interface ........................................................................................................................... 4
3.6
I2S Audio Data Interface ............................................................................................................... 4
3.7
GPIO Outputs ............................................................................................................................... 4
Electrical Characteristics ........................................................................................................................... 5
Receiver Characteristics............................................................................................................................. 6
Serial Interface............................................................................................................................................ 7
6.1
Three-wire Interface Timing ......................................................................................................... 7
6.2
I2C Interface Timing ..................................................................................................................... 8
Register Definition ...................................................................................................................................... 9
Pins Description ........................................................................................................................................ 13
Application Diagram ................................................................................................................................ 15
9.1
Audio Loading Resistance Larger than 32 & TCXO Application: .......................................... 15
9.1.1
Bill of Materials: ......................................................................................................................... 15
9.2
Audio Loading Resistance Lower than 32 & DCXO Application: .......................................... 16
9.2.1
Bill of Materials: ......................................................................................................................... 16
Package Physical Dimension.................................................................................................................... 17
PCB Land Pattern .................................................................................................................................... 18
Change List................................................................................................................................................ 21
Notes....................................................................................................................................................... 21
RDA5802E RDA5802 .................................................................................................................. 22
Contact Information ................................................................................................................................. 23
4
5
6
7
8
9
10
11
12
13
14
15
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 2 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Functional Description
Figure 3-1. RDA5802E FM Tuner Block Diagram
3.1
FM Receiver
The receiver uses a digital low-IF architecture that
avoids the difficulties associated with direct
conversion while delivering lower solution cost
and reduces complexity, and integrates a low
noise amplifier (LNA) supporting the FM
broadcast band (65 to 108MHz), a quadrature
image-reject mixer, a programmable gain control
(PGA), a high resolution analog-to-digital
converters (ADCs), an audio DSP and a highfidelity digital-to-analog converters (DACs).
The LNA has differential input ports (LNAP and
LNAN) and supports any input port by set
according registers bits (LNA_PORT_SEL[1:0]). It
default input common mode voltage is GND.
The limiter prevents overloading and limits the
amount of intermodulation products created by
strong adjacent channels.
The quadrature mixer down converts the LNA
output differential RF signal to low-IF, it also has
image-reject function.
The PGA amplifies the mixer output IF signal and
then digitized with ADCs.
The DSP core finishes the channel selection, FM
demodulation, stereo MPX decoder and output
audio signal. The MPX decoder can autonomous
switch from stereo to mono to limit the output
noise.
The DACs convert digital audio signal to analog
and change the volume at same time. The DACs
has low-pass feature and -3dB frequency is about
30 KHz.
3.2
Synthesizer
The frequency synthesizer generates the local
oscillator signal which divide to quadrature, then
be used to downconvert the RF input to a
constant low intermediate frequency (IF). The
synthesizer reference clock is 32.768 KHz.
The synthesizer frequency is defined by bits
CHAN[9:0] with the range from 65MHz to
108MHz.
3.3
Power Supply
The RDA5802E integrated one LDO which
supplies power to the chip. The external supply
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 3 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
voltage range is 1.8-5.5 V.
3.4
RESET and Control Interface select
The RDA5802E is RESET itself When VIO is
Power up. And also support soft reset by trigger
02H BIT1 from 0 to 1. The control interface is
select by MODE Pin. The MODE Pin is low ,I2C
Interface is select. The MODE Pin is set to VIO,
SPI Interface is select.
3.5
Control Interface
The RDA5802E supports three- wire and I2C
control interface. User could select either of them
to program the chip.
The three-wire interface is a standard SPI
interface. It includes three pins: SEN, SCLK and
SDIO. Each register write is 25-bit long, including
4-bit high register address, a r/w bit, 4-bit low
register address, and 16-bit data (MSB is the first
bit). RDA5802E samples command byte and data
at posedge of SCLK. Each register read is also
25-bit long, including 4-bit high register address, a
r/w bit, 4-bit low register address, and 16-bit data
(MSB is the first bit) from RDA5802E. The turn
around cycle between command byte from MCU
and data from RDA5802E is a half cycle.
RDA5802E samples command byte at posedge of
SCLK, and output data also at posedge of SCLK.
2
transfer, MCU programs registers from register
0x02h high byte, then register 0x02h low byte,
then register 0x03h high byte, till the last register.
RDA5802E always gives out ACK after every byte,
and MCU gives out STOP condition when register
programming is finished. For read transfer, after
command byte from MCU, RDA5802E sends out
register 0x0Ah high byte, then register 0x0Ah low
byte, then register 0x0Bh high byte, till receives
NACK from MCU. MCU gives out ACK for data
bytes besides last data byte. MCU gives out
NACK for last data byte, and then RDA5802E will
return the bus to MCU, and MCU will give out
STOP condition.
Details refer to RDA5802E Programming Guide.
3.6
I2S Audio Data Interface
The RDA5802E supports I2S (Inter_IC Sound Bus)
audio interface. The interface is fully compliant
with I2S bus specification. When setting I2SEN bit
high, RDA5802E will output SCK, WS, SD signals
from GPIO3, GPIO1, GPIO2 as I2S master and
transmitter, the sample rate is 48Kbps
44.1kbps,32kbps.. RDA5802E also support as
I2S slaver mode and transmitter, the sample rate
is less than 100kbps.
Details refer to RDA5802E Programming Guide.
3.7
GPIO Outputs
The I C interface is compliant to I C Bus
Specification 2.1. It includes two pins: SCLK and
SDIO. A I2C interface transfer begins with START
condition, a command byte and data bytes, each
byte has a followed ACK (or NACK) bit, and ends
with STOP condition. The command byte includes
a 7-bit chip address (0010000b) and a R/W bit.
The ACK (or NACK) is always sent out by receiver.
When in write transfer, data bytes is written out
from MCU, and when in read transfer, data bytes
is read out from RDA5802E. There is no visible
2
2
register address in I C interface transfers. The I C
interface has a fixed start register address (0x02h
for write transfer and 0x0Ah for read transfer), and
an internal incremental address counter. If register
address meets the end of register file, 0x3Ah,
register address will wrap back to 0x00h. For write
The RDA5802E has three GPIOs. The function of
GPIOs could programmed with bits GPIO1[1:0],
GPIO2[1:0], GPIO3[1:0] and I2SEN.
If I2SEN is set to low, GPIO pins could be
programmed to output low or high or high-Z, or be
programmed to output interrupt and stereo
indicator with bits GPIO1[1:0], GPIO2[1:0],
GPIO3[1:0]. GPIO2 could be programmed to
output a low interrupt (interrupt will be generated
only with interrupt enable bit STCIEN is set to high)
when seek/tune process completes. GPIO3 could
be programmed to output stereo indicator bit ST.
Constant low, high or high-Z functionality is
available regardless of the state of VA and VD
supplies or the ENABLE bit.
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 4 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
SCK
LEFT CHANNEL
WS
RIGHT CHANNEL
1 SCK
SD
1 SCK
MSB
LSB
MSB
LSB
Figure 3-2. I2S Digital Audio Format
Electrical Characteristics
Table 4-1
SYMBOL
DC Electrical Specification (Recommended Operation Conditions):
DESCRIPTION
MIN
TYP
MAX
UNIT
AVDD
Analog Supply Voltage
1.8
3.3
5.5
DVDD
Digital Supply Voltage
1.8
3.3
5.5
VIO
Interface Supply Voltage
1.5
3.6
Tamb
Ambient Temperature
-20
27
+70
VIL
CMOS Low Level Input Voltage
0.3*DVDD
VIH
CMOS High Level Input Voltage
0.7*VDD
DVDD
VTH
CMOS Threshold Voltage
Table 4-2
SYMBOL
0.5*VDD
DC Electrical Specification (Absolute Maximum Ratings):
DESCRIPTION
MIN
TYP
MAX
UNIT
VIO
Interface Supply Voltage
-0.5
+4
Tamb
Ambient Temperature
IIN
-40
+90
(1)
-10
+10
mA
(1)
-0.3
VIO+0.3
-20
dBm
Input Current
VIN
Input Voltage
Vlna
LNA FM Input Level
Notes:
1. For Pin: SCLK, SDIO, SEN, MODE
Table 4-3
Power Consumption Specification
(VDD = 1.8 to 5.5 V, TA = -25 to 85 , unless otherwise specified)
SYMBOL
DESCRIPTION
CONDITION
TYP
UNIT
IA
Analog Supply Current
ENABLE=1
18
mA
ID
Digital Supply Current
ENABLE=1
mA
IVIO
Interface Supply Current
SCLK and RCLK inactive
90
IAPD
Analog Powerdown Current
ENABLE=0
IDPD
Digital Powerdown Current
ENABLE=0
IVIO
Interface Powerdown Current
ENABLE=0
10
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 5 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Receiver Characteristics
Table 5-1
Receiver Characteristics
(VDD = 2.7 to 5.5 V, TA = -25 to 85 C, unless otherwise specified)
SYMBOL
PARAMETER
CONDITIONS
MIN
BAND=00
TYP
MAX
UNIT
87
108
MHz
BAND=01
76
91
MHz
BAND=10
76
108
MHz
BAND=11
65
76
MHz
1.5
V EMF
General specifications
Fin
Vrf
Rin
Cin
IP3in
am
S200
FM Input Frequency
Sensitivity
1,2,3
(S+N)/N=26dB
LNA Input Resistance
LNA Input Capacitance
150
Input IP3
1,2
AM Suppression
Adjacent Channel Selectivity
AGCD=1
80
m=0.3
40
200KHz
45
pF
dBV
dB
dB
Left and Right Audio
VAFL; VAFR
Frequency Output Voltage
Volume [3:0] =1111
200
mV
(Pins LOUT and ROUT)
(S+N)/N
SCS
THD
AOI
RL
Maximum Signal Plus Noise
1,2,3,5
to Noise Ratio
Stereo Channel Separation
55
60
dB
35
dB
0.03
0.05
0.1
dB
Audio Total Harmonic
1,3,6
Distortion
Audio Output L/R Imbalance
Audio Output Loading
Resistance
Single-ended
32
Pins LNAN, LNAP, LOUT, ROUT and NC(22,23)
Vcom_rfin
Vcom
Vcom_nc
Pins LNAN and LNAP Input
Common Mode Voltage
Audio Output Common
8
Mode Voltage
0.95
1.
Pins NC (22, 23) Common
Floating
Mode Voltage
1.05
! The NC(22, 23) pins SHOULD BE left floating.
Notes:
1. Fin=65 to 108MHz; Fmod=1KHz; de-emphasis=75s; MONO=1; L=R unless noted otherwise;
2. f=22.5KHz;
3. BAF = 300Hz to 15KHz, RBW <=10Hz;
4. |f2-f1|>1MHz, f0=2xf1-f2, AGC disable, Fin=76 to 108MHz;
5. PRF=60dB UV;
6. f=75KHz.
7. Measured at VEMF = 1 m V, f RF = 65 to 108MHz
8. At LOUT and ROUT pins
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 6 of 23
RDA Microelectronics, Inc.
6
6.1
RDA5802E FM Tuner V1.7
Serial Interface
Three-wire Interface Timing
Table 6-1
Three-wire Interface Timing Characteristics
(VDD = 2.7 to 5.5 V, TA = -25 to 85 C, unless otherwise specified)
PARAMETER
SYMBOL
TEST CONDITION
MIN
TYP
MAX
UNIT
SCLK Cycle Time
tCLK
SCLK Rise Time
tR
50
ns
SCLK Fall Time
tF
50
ns
SCLK High Time
tHI
10
ns
SCLK Low Time
tLO
10
ns
SDIO Input, SEN to SCLK Setup
ts
10
ns
SDIO Input, to SCLK Hold
th
10
ns
35
ns
SCLK to SDIO Output Valid
tcdv
Read
10
ns
SEN to SDIO Output High Z
tsdz
Read
10
ns
pF
Digital Input Pin Capacitance
Figure 6-1. Three-wire Interface Write Timing Diagram
Figure 6-2. Three-wire Interface Read Timing Diagram
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 7 of 23
RDA Microelectronics, Inc.
6.2
RDA5802E FM Tuner V1.7
I2C Interface Timing
Table 6-2
I2C Interface Timing Characteristics
(VDD = 2.7 to 5.5 V, TA = -25 to 85 C, unless otherwise specified)
PARAMETER
SYMBOL
TEST CONDITION
MIN
TYP
MAX
UNIT
SCLK Frequency
fscl
400
KHz
SCLK High Time
thigh
0.6
SCLK Low Time
tlow
1.3
Setup Time for START Condition
tsu:sta
0.6
Hold Time for START Condition
thd:sta
0.6
Setup Time for STOP Condition
tsu:sto
0.6
SDIO Input to SCLK Setup
tsu:dat
100
ns
SDIO Input to SCLK Hold
thd:dat
900
ns
STOP to START Time
tbuf
1.3
SDIO Output Fall Time
tf:out
20+0.1Cb
250
ns
tr:in / tf:in
20+0.1Cb
300
ns
Input Spike Suppression
tsp
50
ns
SCLK, SDIO Capacitive Loading
Cb
50
pF
pF
SDIO Input, SCLK Rise/Fall Time
Digital Input Pin Capacitance
Figure 6-3. I C Interface Write Timing Diagram
Figure 6-4. I C Interface Read Timing Diagram
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 8 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Register Definition
REG
BITS
00H
15:8
CHIPID[7:0]
NAME
Chip ID.
FUNCTION
0x58
DEFAULT
02H
15
DHIZ
Audio Output High-Z Disable.
14
DMUTE
Mute Disable.
0 = High impedance; 1 = Normal operation
0 = Mute; 1 = Normal operation
13
MONO
Mono Select.
0 = Stereo; 1 = Force mono
12
BASS
Bass Boost.
10
CLK_DIRECT_MODE
Reference clk (32.768K,12M,)
0 = Disabled; 1 = Bass boost enabled
direct
input
mode.
0=clk_buffer mode;
1=clk directly input mode
9
SEEKUP
Seek Up.
0 = Seek down; 1 = Seek up
8
SEEK
Seek.
0 = Disable stop seek; 1 = Enable
Seek begins in the direction specified by
SEEKUP and ends when a channel is found with
RSSI level above SEEKTH[5:0], or the entire
band has been searched.
The SEEK bit is set low and the STC bit is set
high when the seek operation completes.
7
SKMODE
Seek Mode
0 = wrap at the upper or lower band limit and
continue seeking
1 = stop seeking at the upper or lower band limit
6:4
CLK_MODE[2:0]
000=32.768kHz
000
001=12Mhz
101=24Mhz
010=13Mhz
110=26Mhz
011=19.2Mhz
111=38.4Mhz
1
SOFT_RESET
Soft reset.
If 0, not reset;
If 1, reset.
0
ENABLE
Power Up Enable.
0 = Disabled; 1 = Enabled
03H
15:6
CHAN[9:0]
Channel Select.
0x00
BAND = 0
Frequency =
Channel Spacing (kHz) x CHAN+ 87.0 MHz
BAND = 1or 2
Frequency =
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 9 of 23
RDA Microelectronics, Inc.
REG
BITS
RDA5802E FM Tuner V1.7
NAME
FUNCTION
DEFAULT
Channel Spacing (kHz) x CHAN + 76.0 MHz
BAND = 3
Frequency =
Channel Spacing (kHz) x CHAN + 65.0 MHz
CHAN is updated after a seek operation.
4
TUNE
Tune
0 = Disable
1 = Enable
The tune operation begins when the TUNE bit is
set high. The STC bit is set high when the tune
operation completes.
The tune bit is reset to low automatically when
the tune operation completes..
3:2
BAND[1:0]
Band Select.
00
00 = 87108 MHz (US/Europe)
01 = 7691 MHz (Japan)
10 = 76108 MHz (world wide)
11 = 65 76 MHz East Europe
1:0
SPACE[1:0]
Channel Spacing.
00
00 = 100 kHz
01 = 200 kHz
10 = 50kHz
04H
14
STCIEN
Seek/Tune Complete Interrupt Enable.
0 = Disable Interrupt
1 = Enable Interrupt
Setting STCIEN = 1 will generate a low pulse on
GPIO2 when the interrupt occurs.
11
DE
De-emphasis.
0 = 75 s; 1 = 50 s
9
SOFTMUTE_EN
If 1, softmute enable
AFCD
AFC disable.
If 0, afc work;
If 1, afc disabled.
6
I2S_ENABLED
I2S bus enable
If 0, disabled;
If 1, enabled.
5:4
GPIO3[1:0]
General Purpose I/O 3.
00
00 = High impedance
01 = Mono/Stereo indicator (ST)
10 = Low
11 = High
3:2
GPIO2[1:0]
General Purpose I/O 2.
00
00 = High impedance
01 = Interrupt (INT)
10 = Low
11 = High
1:0
GPIO1[1:0]
General Purpose I/O 1.
00
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 10 of 23
RDA Microelectronics, Inc.
REG
BITS
RDA5802E FM Tuner V1.7
NAME
FUNCTION
DEFAULT
00 = High impedance
01 = Reserved
10 = Low
11 = High
05H
15
INT _MODE
If 0, generate 5ms interrupt;
If 1, interrupt last until read reg0CH action
occurs.
14:8
SEEKTH[6:0]
Seek Threshold. RSSI scale is logarithmic.
7:6
LNA_PORT_SEL[1:0]
LNA input port selection bit:
0001000
0000000 = min RSSI
10
00: no input
01: LNAN
10: LNAP
11: dual port input
5:4
LNA_ICSEL_BIT[1:0]
10
Lna working current bit:
00=1.8mA
01=2.1mA
10=2.5mA
11=3.0mA
3:0
VOLUME[3:0]
1111
DAC Gain Control Bits (Volume).
0000=min; 1111=max
Volume scale is logarithmic
06H
12
I2s_mode_select
If 0, master mode;
If 1, slave mode.
7:4
I2s_ws_cnt[4:0]
Only valid
in master mode
4'b1000:
4'b0111:
4'b0110:
4'b0101:
4'b0100:
4'b0011:
4'b0010:
4'b0001:
WS_STEP_48;
WS_STEP=44.1kbps;
WS_STEP=32kbps;
WS_STEP=24kbps;
WS_STEP=22.05kbps;
WS_STEP=16kbps;
WS_STEP=12kbps;
WS_STEP=11.025kbps;
0000
4'b0000: WS_STEP=8kbps;
0AH
14
STC
Seek/Tune Complete.
0 = Not complete
1 = Complete
The seek/tune complete flag is set when the seek
or tune operation completes.
13
SF
Seek Fail.
0 = Seek successful; 1 = Seek failure
The seek fail flag is set when the seek operation
fails to find a channel with an RSSI level greater
than SEEKTH[5:0].
10
ST
Stereo Indicator.
0 = Mono; 1 = Stereo
Stereo indication is available on GPIO3 by
setting GPIO1[1:0] =01.
9:0
READCHAN[9:0]
8h00
Read Channel.
BAND = 0
Frequency
Channel
Spacing
(kHz)
READCHAN[9:0]+ 87.0 MHz
BAND = 1 or 2
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 11 of 23
RDA Microelectronics, Inc.
REG
BITS
RDA5802E FM Tuner V1.7
NAME
FUNCTION
Frequency
Channel
Spacing
DEFAULT
(kHz)
(kHz)
READCHAN[9:0]+ 76.0 MHz
BAND = 3
Frequency
Channel
Spacing
READCHAN[9:0]+ 65.0 MHz
READCHAN[9:0] is updated after a tune or seek
operation.
0BH
15:9
RSSI[6:0]
RSSI.
000000 = min
111111 = max
RSSI scale is logarithmic.
8
FM TRUE
1 = the current channel is a station
0 = the current channel is not a station
7
FM_READY
1=ready
0=not ready
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 12 of 23
RDA Microelectronics, Inc.
NC
NC
GPIO1
GPIO2
GPIO3
Pins Description
GND
24
23
22
21
20
19
GND
18
AVDD
LNAN
17
GND
RFGND
16
LOUT
LNAP
15
ROUT
GND
14
GND
GND
13
DVDD
GND
PAD
10
11
RCLK
12
VIO
SDIO
MODE
SCLK
RDA5802E
SEN
RDA5802E FM Tuner V1.7
Figure 8-1. RDA5802E Top View
Table 8-1
RDA5802E Pins Description
SYMBOL
GND
LNAN,LNAP
RFGND
MODE
SEN
SCLK
SDIO
RCLK
VIO
AVDD
ROUT,LOUT
DVDD
GPIO1,GPIO2,GPIO3
NC
PIN
DESCRIPTION
1,5,6,14,17,24 Ground. Connect to ground plane on PCB
LNA input port. For single-ended input, LNAN should
2,4
be connected to RFGND
3
LNA ground. Connect to ground plane on PCB
Control Interface select
The MODE Pin is low ,I2C Interface is select.
7
The MODE Pin is set to VIO, SPI Interface is select.
8
9
10
11
12
18
15,16
14
19,20,21
22,23
Latch enable (active low) input for serial control bus
Clock input for serial control bus
Data input/output for serial control bus
32.768KHz crystal oscillator and reference clock input
Power supply for I/O
Power supply for analog section
Right/Left audio output
Power supply for digital section
General purpose input/output
No Connect
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 13 of 23
RDA Microelectronics, Inc.
Table 8-2
RDA5802E FM Tuner V1.7
Internal Pin Configuration
SYMBOL
PIN
LNAN/LNAP
2/4
RCLK
11
DESCRIPTION
47K
Sin
SDIO\SCLK
SCLK/SDIO
9/10
Sout
MN1
GPIO1/GPIO2/GPIO3
19/20/21
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 14 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Application Diagram
9.1
Audio Loading Resistance Larger than 32 & TCXO Application:
Notes:
1. J1: Common 32 Resistance
Headphone;
2. U1: RDA5802E Chip;
19
3. V1: Analog and Digital Power
Supply (1.8~5.5V);
4. FM Choke (L3 and C3) for Audio
Common and LNA Input
Common;
5. Pins NC(22, 23), Should be
Leaved Floating;
6.Set MODE to select control
interface(GNDI2C,VIOSPI);
7
6. Place C6 Close to AVDD pin.
Figure 9-1. RDA5802E FM Tuner Application Diagram (TCXO Application)
9.1.1
Bill of Materials:
COMPONENT
U1
VALUE
RDA5802E
J1
DESCRIPTION
Broadcast FM Radio Tuner
SUPPLIER
RDA
Common 32 Resistance Headphone
C2
100pF
Couple CAP
Murata
L3/C3
100nH/24pF
LC Chock for LNA Input
Murata
C4,C5
125F
Audio AC Couple Capacitors
Murata
C6
24nF
Power Supply Bypass Capacitor
Murata
F1/F2
1.5K@100MHz
FM Band Ferrite
Murata
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 15 of 23
RDA Microelectronics, Inc.
9.2
RDA5802E FM Tuner V1.7
Audio Loading Resistance Lower than 32 & DCXO Application:
Notes:
F1 1.5K@100MHz C4 125uF
1. J1: Common 32 Resistance
J1
F2
1.5K@100MHz
C5 125uF
Headphone
2. U1: RDA5802E Chip
L3 100nH
3. V1: Analog and Digital Power
Supply (1.8~5.5V)
C3 24pF
5. Pins NC(22, 23),Should be
V1
Leaved Floating;
6.Set MODE to select control
C6
24nF
interface(GNDI2C,VIOSPI);
7. Place C6 Close to AVDD pin
13
SCLK
SDIO
VIO
Figure 9-2. RDA5802E FM Tuner Application Diagram (32.768K crystal,I2C bus mode)
9.2.1
Bill of Materials:
COMPONENT
U1
VALUE
RDA5802E
J1
DESCRIPTION
Broadcast FM Radio Tuner
SUPPLIER
RDA
Audio Amplifier
C4/C5
125uF
Audio AC Couple Capacitors
Murata
L3/C3
100nH/24pF
LC Chock for LNA Input
Murata
C6
24nF
Power Supply Bypass Capacitor
Murata
F1/F2
1.5K@100MHz
FM Band Ferrite
Murata
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 16 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
10 Package Physical Dimension
Figure 10-1 illustrates the package details for the RDA5802E. The package is lead-free and
RoHS-compliant.
MIN
D
NOM
MAX
4.00 BSC
4.00 BSC
D2
2.60
2.70
2.80
E2
2.60
2.70
2.80
0.50 BSC
0.30
0.40
0.50
0.18
0.25
0.30
0.80
0.90
1.00
A1
0.00
0.02
0.05
A3
0.20 ref
Figure 10-2. 24-Pin 4x4 Quad Flat No-Lead (QFN)
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 17 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
11 PCB Land Pattern
Figure 18.Classification Reflow Profile
Profile Feature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
Average Ramp-Up Rate
3 oC/second max.
3 oC/second max.
-Temperature Min (Tsmin)
100 oC
150 oC
-Temperature Max (Tsmax)
100 oC
200 oC
-Time (tsmin to tsmax)
60-120 seconds
60-180 seconds
-Temperature (TL)
183 oC
217oC
-Time (tL)
60-150seconds
60-150 seconds
Peak /Classification
Temperature(Tp)
See Table-II
See Table-III
Time within 5 oC of actual
Peak Temperature (tp)
10-30 seconds
20-40 seconds
Ramp-Down Rate
6 oC/second max.
6 oC/seconds max.
Time 25 oC to Peak
Temperature
6 minutes max.
8 minutes max.
(TSmax to Tp)
Preheat
Time maintained above:
Table-I Classification Reflow Profiles
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 18 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
Volume mm3
Volume mm3
<350
350
2.5mm
240 + 0/-5 o C
225 + 0/-5 o C
2.5mm
225 + 0/-5 o C
225 + 0/-5 o C
Package Thickness
Table II SnPb Eutectic Process Package Peak Reflow Temperatures
Package
Volume mm3
Volume mm3
Volume mm3
Thickness
350
350-2000
2000
1.6mm
260 + 0 o C *
260 + 0 o C *
260 + 0 o C *
1.6mm 2.5mm
260 + 0 o C *
250 + 0 o C *
245 + 0 o C *
2.5mm
250 + 0 o C *
245 + 0 o C *
245 + 0 o C *
*Tolerance : The device manufacturer/supplier shall assure process compatibility up to and
including the stated classification temperature(this mean Peak reflow temperature + 0 o C. For
example 260+ 0 o C ) at the rated MSL Level.
Table III Pb-free Process Package Classification Reflow Temperatures
Note 1: All temperature refer topside of the package. Measured on the package body surface.
Note 2: The profiling tolerance is + 0
capability)whatever
C, - X
C (based on machine variation
is required to control the profile process but at no time will it exceed - 5 o C. The
producer assures process compatibility at the peak reflow profile temperatures defined
in Table III.
Note 3: Package volume excludes external terminals(balls, bumps, lands, leads) and/or non
integral heat sinks.
Note 4: The maximum component temperature reached during reflow depends on package the
thickness and volume. The use of convection reflow processes reduces the thermal
gradients between packages. However, thermal gradients due to differences in
thermal mass of SMD package may sill exist.
Note 5: Components intended for use in a lead-free assembly process shall be evaluated
using the lead free classification temperatures and profiles defined in Table-I II III
whether or not lead free.
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 19 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
RoHS Compliant
The product does not contain lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB)
or polybrominated diphenyl ethers (PBDE), and are therefore considered RoHS compliant.
ESD Sensitivity
Integrated circuits are ESD sensitive and can be damaged by static electricity. Proper ESD
techniques should be used when handling these devices.
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 20 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
12 Change List
REV
V1.0
DATE
2009-03-03
AUTHER
ChunZhao
CHANGE DESCRIPTION
Original Draft.
13 Notes
1:
VIO
7
8
SCLK
SDIO
9
10
7
MODE
SEN
SEN
SCLK
SCLK
SDIO
SDIO
I2C
8
9
10
MODE
SEN
SCLK
SDIO
SPI
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 21 of 23
RDA Microelectronics, Inc.
14
RDA5802E FM Tuner V1.7
RDA5802E RDA5802
15802E 0x0Ch58030x0Dh5804 58005802
5802E;
2FM 4 LNAP
2 LNAN
5802E
3 5802E I2C 001000000100011100000
4RCLK 32.768K PCB
32.768K
5LNAN & LANP 0 0
MP3
100pF
ESD
I2C
SNR
SEN
RDS
I2C
32K
5802E
5000V
sclk
250mV
1.85.5V (1.8~2V )
57dB
-109dBm
21.5mA
5802
5802
32K
0x02h
bit<10> 1
5802
2000V
sclk
200mV
2.7~5.5V
54dB
-107dBm
20mA
32K
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 22 of 23
RDA Microelectronics, Inc.
RDA5802E FM Tuner V1.7
15 Contact Information
RDA Microelectronics (Shanghai), Inc.
Suite 1108 Block A, e-Wing Center, 113 Zhichun Road Haidian District, Beijing
Tel:
86-10-62635360
Fax:
86-10-82612663
Postal Code: 100086
Suite 302 Building 2, 690 Bibo Road Pudong District, Shanghai
Tel:
86-21-50271108
Fax:
86-21-50271099
Postal Code: 201203
Copyright RDA Microelectronics Inc. 2006. All rights are reserved.
Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information contained herein is the exclusive property of RDA and shall not be distributed, reproduced, or disclosed in whole or in
part without prior written permission of RDA.
Page 23 of 23
