ENVIROSHEET
SHEET MEMBRANE WATERPROOFING SYSTEM
Building Materials Group
ENVIROSHEET
COMPOSITION AND MATERIALS
Envirosheet is a composite membrane consisting of
specially formulated rubberized asphalt integrally
bonded to a cross laminated polyethylene liner
produced at a minimum 60 mil (1.5 mm) thickness.
The membrane is supplied in rolls 36 (91.4 cm) wide
by 66.7' (20.3 m) long; 200 square feet (18.6 sq m) per
roll.
Self-Adhering
Membrane
Waterproofing
System
NVIROSHEET is a rubberized-asphalt sheet membrane system designed to waterproof vertical and
horizontal structural concrete, masonry and wood
substrates. Envirosheet's quality construction and adhesion to the substrate provides long term performance and
ensures uniform, consistent waterproofing protection.
Envirosheet is excellent for waterproofing below grade
foundation walls, plaza decks, parking decks, tunnels,
interior slabs and earth covered structures.
Installation of Envirosheet is fast and easy. Simply
position the product into place over a properly
prepared and primed substrate. Envirosheet easily
contours to substrate transitions and can be cut on site
to form around penetrations. The result is always a
reliable uniform waterproofing system.
Envirosheet is designed for applications where ambient
and surface temperatures are 50F (10C) and above.
The membrane is also available in a low temperature
formulation Envirosheet LT designed for applications when temperatures are between 60F to 25F
(16C to -4C). Installation is not recommended when
the temperature is 25F (-4C) or lower.
Enviroprimer SB and Enviroprimer WB (water based)
are used to condition all surfaces where Envirosheet
membranes will be applied. The primers prepare the
substrate for the Envirosheet membrane and provide
excellent long-term adhesion.
Enviromastic trowel-grade, cold applied elastomeric
mastic is used in conjunction with Envirosheet membranes for detailing drains, surface transitions, penetrations, terminations, and other specified details.
Envirosheet should be protected with Aquadrain,
Protection Mat 10V or other approved protection board
immediately following installation.
ADVANTAGES OF ENVIROSHEET WATERPROOFING
Fully-Adhered Membrane
Factory Controlled Thickness
High Hydrostatic Resistance
High Chemical Resistance
Cold Applied
Easy To Apply
Excellent Elongation
Two-Component Membrane
Substrate Compatibility
Flexibility
Eliminates water migration between membrane and substrate
Insures consistent application rate
Tested to over 150 feet of hydrostatic head pressure
Resists attack from many chemicals
Eliminates need for heating equipment and danger from hot materials
Minimize application errors
Resilient to structural movement, bridging small cracks and joints
Combines high strength and chemical resistance of HDPE with
superior adhesion and self-sealing properties of modified asphalt
Can be applied to structural concrete, masonry and wood surfaces
Membrane easily conforms surface transitions and corners
APPLICATIONS
FOUNDATION WALLS INTERIOR SLABS
PLAZA DECKS
BRIDGE DECKS
PARKING DECKS
PLANTERS
TUNNELS
BALCONIES
EARTH COVERED STRUCTURES
Below-grade Concrete Wall Installation
APPLICATION INSTRUCTIONS
Aquadrain
Envirosheet
aa
Envirosheet membrane should be applied during
dry weather conditions at temperatures above 50F
(10C) - use Envirosheet LT Membrane when the
temperature is 60F to 25F (16C to -4C). The
substrate must be clean, dry and free of surface
irregularities. Concrete should be cured a minimum
of seven days prior to installation. Lightweight
structural concrete should be cured a minimum 14
days.
Compacted
Backfill
Aquadrian
Envirosheet
Prime all surfaces and allow primer to dry for a
minimum 30 minutes to a tacky finish. Areas
primed and not covered with membrane within 24
hours should be re-primed.
Waterstop-RX
Drain Tile
Prepare all drains, penetrations, and surface transitions with proper accessory detailing products.
Start membrane application by removing the release
paper. Apply the membrane, beginning at the low
point (around drains) and install toward the high
point. Lap membrane side edges and ends a minimum 2-1/2" (65 mm). Roll membrane immediately
after placement to ensure full adhesion. Install a 12"
(300 mm) wide membrane strip in all inside and
outside corners before applying full sheet. All membrane terminations should receive a trowel of
Enviromastic.
A protection course should be applied at the end of
each day's work to prevent damage caused by other
trades, construction materials or backfill.
To ensure maximum waterproofing protection, use
Aquadrain prefabricated drainage composite in
conjunction with Envirosheet waterproofing.
Waterstop-RX
Enviromastic
Typical Envirosheet Waterproofing Detail
Split-slab Plaza Deck Installation
ENVIROSHEET MEMBRANE PHYSICAL PROPERTIES
Property
Color
Thickness
Hydrostatic Head Resistance
Tensile Strength, Membrane
Tensile Strength, Film
Elongation
Permeance
Low Temperature Flexibility
Crack Cycling (100 Cycles)
Peel Strength
Lap Adhesion
Puncture Resistance, Membrane
Water Absorption, 72 Hours
Exposure to Fungi
Test Method
Typical Value (metric)
ASTM D 5385
ASTM D 412 (C) Mod.
ASTM D 412
ASTM D 412 (C) Mod.
ASTM E 96 (B)
ASTM D 1970
ASTM C 836
ASTM D 903
ASTM D 1876 Mod.
ASTM E 154
ASTM D 570
GSA-PBS-07115
Dark Gray-Black
60 Mils (1.5 mm)
231 ft. (70 m)
300 psi (2,068 kPa)
5,000 psi (34,475 kPa)
300% min.
0.05 perms
Unaffected at -20F (-29C)
Unaffected at -25F (-32C)
10 lbs./in. width (1.8 kN/m)
7.0 lbs./in. width (1.2 kN/m)
61 lbs. (0.275 kN)
0.09%
Unaffected
CODES, CERTIFICATIONS, STANDARDS
Federal Construction Guide Specification
FCGS 07111
General Services Administration
PBS 07115
Veteran's Administration
H-08-1 Section 07113
Department of the Navy
NFGS-07111
Corps of Engineers
CEGS 07111-3-82
International Conference of Building Officials
Section 1813.0
American Railway Engineering Association
WARRANTY
The information contained herein supersedes all previous versions printed prior
to February 2002 and is believed to be accurate and reliable. CETCO makes no
warranty of any kind and accepts no responsibility for the results obtained
through application of this information. CETCO reserves the right to update
information without notice.
CETCO warrants its Envirosheet products to be free of defects in material and
workmanship when delivered to CETCO's customers. CETCO further warrants
that its products conform to the specifications published in CETCO's current
sales literature. If a Envirosheet product is defective or does not meet published
specifications and our customer gives notice to CETCO before installing the
product, CETCO will replace the product without charge to our customer or
refund the purchase price at CETCO's election. Replacing the product or obtaining a refund are the buyer's sole remedy for a breach, and CETCO will not be
liable for any consequential damage attributed to a defective product. This
warranty is exclusive and in place of all other warranties expressed or implied
and CETCO makes no other warranty as to its products.
A wholly owned subsidiary of AMCOL International Corporation
Building Materials Group
1500 West Shure Drive
Arlington Heights, IL 60004 USA.
(847)392-5800 Fax (847)506-6195
http://www.cetco.com
(800) 527-9948
Quality from the ground up.
Form No. ENSHT-101
Printed in USA.
FEBRUARY 2002
2002 CETCO
