SERVICE BULLETIN
QUALITY INFORMATION ANALYSIS
OVERSEAS SERVICE DEPT. MITSUBISHI MOTORS CORPORATION
SERVICE BULLETIN
Subject:
No.: MSB-98E54-501
Date: 1998-05-15
CORRECTION OF BATTERY TYPE
CHASSIS
ELECTRICAL
OVERSEAS
CORRECTION
Group:
SERVICE
DEPT
<Model>
(EC,EXP)GALANT
(EA0)
<M/Y>
97-10
Draft No.: 98JY011015
R. USAMI - MANAGER
QUALITY INFORMATION ANALYSIS
1. Description:
This Service Bulletin informs you of correction of the type of battery installed on the car equipped
with the 4G63 or 6A13 engine.
2. Applicable Manuals:
Manual
97 GALANT/GALANT WAGON
Technical Information Manual
97 GALANT/GALANT WAGON
Workshop Manual Chassis
Pub. No.
PYDE9604
PYDE9611
PYDS9612
PYDF9613
PYDG9614
PYDD9615
PYDW9616
Language
(English) 7-4
(English) 54-6
(Spanish)
(French)
(German)
(Dutch)
(Swedish)
3. Details:
97 GALANT/GALANT WAGON Technical Information Manual, Page 2
97 GALANT/GALANT WAGON Workshop Manual Chassis, Page 3
Page(s)
7-4
EQUIPEMENT - Battery / Immobilizer System
BATTERY
The specification of the battery are as follows.
<Correct>
SPECIFICATIONS
75D23L
Items
Petrol-powered vehicles
Diesel-powered vehicles
Type
75D26L
95D31L
Capacity (5HR) ah.
52
70
Reserve capacity min.
118
159
Cold cranking current A [at-18C]
520
622
<Incorrect>
IMMOBILIZER SYSTEM
The immobilizer system consist of the ignition
key, the antenna, the immobilizer-ECU, and the
engine-ECU. The ignition key has a built-in
transponder as the oscillator. The antenna is
installed on the steering lock key cylinder. The
system prevents the engine from theft. The
operation is as follows.
1. When the ignition switch is turned on, the
immobilizer-ECU supplies power to the
transponder inside the ignition key via the
antenna.
2. The energized transponder outputs an ID
code to the immobilizer-ECU via the antenna.
3. The immobilizer-ECU compares the input ID.
code with the registered ID code. If they are
the same, the immobilizer-ECU sends a
starting permission signal to the engine-ECU If
they are not the same or if the ID code input
cannot be received, the immobilizer-ECU sends
a starting prohibition signal to the engine-ECU.
As mentioned above, only the ID code, which is
specific to each ignition key, permits the engine
to start. Therefore, the engine can never be
started by means of a forged key or by
connecting the ignition wiring directly. The
system is significantly safe and reliable against
theft. In addition, the driver has only to turn the
ignition switch to the ON position to activate the
immobilizer system. If the ignition key is lost or
another ignition key is added, the ID code can be
registered or erased by using the MUT-II.
Antenna
ID code
Antenna
ID code
Electromagnetic
wave receiver
and transmitter
ID code
Power
Ignition key
Steering lock key
cylinder
CPU
Starting
permission
code
Transmission
circuit
Engine-ECU
MUT-II
16M0192
NOTE
*1: Starting permission code
*2: Permission confirmation code
54-6
CHASSIS ELECTRICAL - Battery
54100120176
BATTERY TESTING PROCEDURE
TEST STEP
(1) Turn headlamps on for 15 seconds.
(2) Turn headlamp off for 2 minutes to allow
battery voltage to stabilise.
(3) Disconnect cables.
OK
Read open circuit voltage
OK: Open circuit voltage is more than 12.4V
OK
NG
(1) Connect a load tester to the battery
(2) Load the battery at the recommended
discharge rate (see LOAD TEST RATE
CHART) for 15 seconds.
(3) Read voltage after 15 seconds, then
remove load.
(4) Compare the measured value with the
minimum voltage (see LOAD TEST
RATE CHART).
OK: Higher than minimum voltage
NG
Charge battery at 5 amps. (see LOAD TEST RATE CHART)
Retest
Replace battery
OK
Normal
<Correct>
75D23L
LOAD TEST RATE CHART
Battery type
Charging time when fully discharged
h [5-amp rated current charging]
Load test (Amps)
75D26L
11
95D31L
14
260
310
LOAD TEST CHART
Temperature C
21 and
above
16
10
-1
-7
-12
-18
Minimum voltage V
9.6
9.5
9.4
9.3
9.1
8.9
8.7
8.5
