MGBDI-series
Three Phase Bidirectional Dual Mode Hybrid Inverter for Mini-grid System
MGBDI series is a Three phase bidirectional dual mode hybrid inverter for mini-grid system. It can operate with
diesel generator, batteries and external DC charge controller. It capable of functioning as a main supply power
source as well as providing automatic control and management of a generator and battery bank. The inverter
features very high efficiency in both charger and inverter modes with maximum efficiency of 95%. It is suitable
for hybrid power system with supplement diesel generator in off-grid areas.
Three phase bidirectional inverter with built-in output transformer
Low harmonic distortion (less than 4%)
High efficiency > 95%
High reliability design for remote area
Seperate DC Bus for multiple sourcen charging
Capable to use with multiple renewable energy sources in both DC
coupling and AC coupling such as solar panel, wind turbine generator
and micro hydro generator
DC external charge control
Monitor energy available from the renewable energy (DC) sources
and minimize the charging current from the diesel generator
Automatic / Manual generator control
Automatic battery equalization (option) to prevent battery capacity
loss and prolong battery life
Battery temperature compensation (option)
Preset time schedule by System Command Unit (SCU) for automatic
controlling the auxiliary power sources such as generators in mini-grid
system (option)
Operate with Hybrid System Control Command Unit (HCCU)
ISO 9001 and ISO 14001 certified factory
R S T
DC BUS
Wind Turbine
Grid Connected System
Generator
PV Array
VSC
MPPT Charge Controller
CCVSI
PV-Grid Connected System
PV Array
CCVSI
MPPT Charge Controller
PV Array
PV Array
MPPT Charge Controller
MGBDI-series
CCVSI
PV Array
Wind Turbine
Wind Turbine
Charge Controller
Battery Bank
AC Loads in Village
MGBDI-series
Three Phase Bidirectional Dual Mode Hybrid Inverter for Mini-grid System
MODEL
RATED POWER
BATTERY
MGBDI-150-480
MGBDI-200-480
MGBDI-250-480
MGBDI-300-480
150 kW
200 kW
250 kW
300 kW
200 A
280 A
350 A
418 A
400 A
500 A
Nominal Voltage
Max. charging current
EXTERNAL DC
Nominal voltage
CHARGER
Maximum current
480 Vdc
480 Vdc
300 A
DC charge control
AC INPUT
Recommended
400 A
Relay dry contact 10 A (for over external charge protection)
> 300 kW
> 400 kW
> 500 kW
> 600 kW
generator power
Voltage
380 / 400 / 415 Vac (L-L), 220 / 230 / 240 Vac (L-N) 10%
Phase
Three phase
Frequency
50 / 60 Hz 3 Hz
Automatic start / stop
AC OUTPUT
Relay dry contact 10 A (ACC and start pluse)
Voltage
380 / 400 / 415 Vac (L-L), 220 / 230 / 240 Vac (L-N)
Voltage regulation
3% (steady load), < 7% at 100% step load within 0.1 sec.
Phase
Three phase
Frequency
50 / 60 Hz 0.1% (auto sensing)
Wave form
Pure sine wave
THDi
Max. surge current
total < 4%
ISOLATION
Galvanic isolation
yes
EFFICIENCY
Inverter peak efficiency
PROTECTION
INDICATOR
200%
> 95%
Over current, Over load, Short circuit, Over temperature, Over voltage, Under voltage
LED
Stand by/Run, Inverter, Charging, Load on Inverter,
Overload, Low Battery, High temperature, Fault
LCD display
Inverter (voltage, current, frequency, power), Generator (voltage, current, frequency, power),
Battery (voltage, current, state of charge(%)), External DC charging current, Equalization date,
Battery temperature (option),Today Energy (Inverter, Battery), Accumulated energy (Inverter,
Battery), System status, Time, Date, Heat sink temperature, Data Log
AUDIABLE
Low battery, Inverter fault, High temperature
ALARM
COOLING
ENVIRONMENT
Automatic cooling fan
Temperature
0 - 45C
Relative humidity
DESIGN
0 - 95 % (Non - condensing)
Standard
AS/NZ 3100:2002
REGULATION
DIMENSION
Control Unit
80 x 205 x 105
W x H x D (cm)
Transformer Unit
120 x 205 x 105
WEIGHT
Control Unit
(approx. in kg)
Transformer Unit
D1*
D2**
110 x 205 x 105
110 x 205 x 105
110 x 205 x 105
110 x 205 x 105
550
550
775
775
775
1,200
1,320
1,220
1,300
1,500
D1* = 80 x 205 x 105 cm for control unit and 120 x 205 x 105 for transformer unit, D2** = 110 x 205 x 105 cm for control unit and transformer unit.
Continuous product development is our commitment. In that manner, the above specifications may be changed without prior notice.
SFG TECHNOLOGY (M) SDN BHD
313, 3rd Floor, Block B, Kelana Square,
No.17, Jalan SS7/26, Kelana Jaya,
47301 Petaling Jaya, Selangor, Malaysia
Tel: +6 03 7880 9360, Fax: +6 03 7805 1652
M.SFG.BRO.INV.1075 Rev.1.00/2014
Service in Malaysia: SFG TECHNOLOGY (M) SDN BHD. 313, 3rd Floor, Block B, Kelana Square,
No.17, Jalan SS7/26, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia
Tel: +6 03 7880 9360, Fax: +6 03 7805 1652
Service in Phillipines: Green-Tech Enterprise No. 31 Santan St.,Ynchausti Subd., Potrero,
Malabon, Metro Manila 1475 Philippines. Tel: +63 2 367 7824-25 ,28 Fax: +63 2 447 7567
Service in Thailand: Best Engineering Service Co.,Ltd. 24/79 Moo 5, Bangna-Trad Rd.,
Bangsaotong, Bangsaotong, Samutprakan Tel: +66 2 740 1033-4 Fax: +66 2 740 1034
