European
Automobile
Manufacturers
Association
ACEA EUROPEAN OIL SEQUENCES
2012
SERVICE FILL OILS FOR
GASOLINE ENGINES
LIGHT DUTY DIESEL ENGINES
ENGINES WITH AFTER TREATMENT DEVICES and
HEAVY DUTY DIESEL ENGINES
Laboratory tests for gasoline and light duty diesel engine oils,
Engine tests for gasoline and light duty diesel engine oils,
Laboratory tests for engine with after treatment devices,
Engine tests for engine with after treatment devices,
Laboratory tests for heavy duty diesel engine oils,
Engine tests for heavy duty diesel engine oils.
ACEA
Avenue des Nerviens 85
B-1040 Bruxelles
Tel (32) 2 732 55 50
Fax (32) 2 738 73 10
(32) 2 738 73 11
[email protected];
[email protected]
www.ACEA.be
TVA BE 444 072 631
SGB 210-0069404-04
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCES FOR SERVICE-FILL OILS
Dec. 2012
This document details the ACEA 2012 European Oil Sequences for Service-fill Oils for Gasoline engines, for Light Duty
Diesel engines, for Gasoline & Diesel engines with after treatment devices and for Heavy Duty Diesel engines. These
sequences define the minimum quality level of a product for presentation to ACEA members. Performance parameters
other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
These sequences will replace the ACEA 2010 sequences as a means of defining engine lubricant quality from
st
1 December 2012.
CONDITIONS FOR USE OF PERFORMANCE CLAIMS AGAINST THE ACEA OIL SEQUENCES
ACEA requires that any claims for Oil performance to meet these sequences must be based on credible data and
controlled tests in accredited test laboratories.
ACEA requires that engine performance testing used to support a claim of compliance with these ACEA sequences
should be generated according to the European Engine Lubricants Quality Management System (EELQMS), but ACEA
reserves the right to define alternatives in exceptional cases.
1
EELQMS which is described in the ATIEL Code of Practice , addresses product development testing and product
performance documentation, and involves the registration of all candidate and reference oil testing and defines the
compliance process. Compliance with the ATIEL Code of Practice is mandatory for any claim to meet the requirements of
the 2012 issue of the ACEA sequences. Therefore ACEA requires that claims against the ACEA oil sequences can only
be made by oil companies or oil distributors who have signed the EELQMS oil marketers Letter of Conformance (for
details: www.atiel.org).
The ACEA oil sequences are underlying a constant development. Replacement tests and other changes required by the
European automobile manufacturers are integrated and new issues are published on a regular basis. As new editions are
published older editions have to be withdrawn. Validities of new and old editions are overlapping for limited periods of time
as shown in the following table and the accompanying text below. When a new ACEA sequence is introduced, oils with
claims against the previous can be marketed only for another two years.
Sequence Issue
2004
2007
2008
2010
2012
First allowable use
Mandatory for new claims
Oils with this claim may be
marketed until
1st November 2004
1st February 2007
22nd December 2008
22nd December 2010
14th December 2012
1st November 2005
1st February 2008
22nd December 2009
22nd December 2011
14th December 2013
31st December 2009
23rd December 2010
22nd December 2012
22nd December 2014
...
Table: For the 2012 issue of the ACEA Oil Sequences: First claims can be made from 14th December 2012. For another
year (until 14th December 2013), oil marketers can still make new claims against ACEA 2010. Starting with 14th
December 2013 every new claim has to be made against the 2012 ACEA Oil Sequences. All engine oils using
nd
claims against the 2010 ACEA Sequences can be continued to be marketed until 22 December 2014.
- First allowable use means that claims cannot be made against the specification before the date indicated.
- Mandatory for new claims means that from this date onward all claims for new oil formulations must be made
according to the latest ACEA Sequence Issue. Up to that date new claims can also be made according to the
previous ACEA Sequence Issue. After the date indicated no new claims to the previous ACEA sequence can be
made. Then all oil formulations must be developed according to the latest ACEA release.
- Oils with this claim may be marketed until means that no further marketing of oils with claims to this issue is
allowed after the date indicated.
The marketer of an oil claiming ACEA performance requirements is responsible for all aspects of product liability.
Where limits are shown relative to a reference oil, then these must be compared to the last valid Reference Result on that
test stand prior to the candidate and using the same hardware. Further details will be in the ATIEL Code of Practice.
Where claims are made that Oil performance meets the requirements of the ACEA sequences (e.g. product literature,
packaging, labels) they must specify the ACEA Class and Category (see Nomenclature & ACEA Process for definitions).
The ATIEL Code of Practice is the sole property of ATIEL and is available from ATIEL (Association Technique de
lIndustrie Europenne des Lubrifiants), Boulevard du Souverain 165, B-1160 Brussels, Belgium.
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCES FOR SERVICE-FILL OILS
Dec. 2012
CERTIFICATION and REGISTRATION
Claims against the ACEA Oil Sequences can be made on a self-certification basis. ACEA asks oil marketers wishing to
use the ACEA claims to register their product with the registration system on the ACEA website.
All information needed for registration is requested on a form which is available in the appropriate section of the ACEA
website (www.acea.be).
Engine Oils claiming any of the ACEA oil sequences should be registered directly after their launch into the market. After
completing the form it will be saved on the ACEA server. If claims are no longer needed oil companies are asked to delete
their registration.
If claims are continued to be used after three years re-registration is needed.
REPLACEMENT of CCMC sequences
The chart below shows the evolution of the engine oil specifications commonly developed by the European Automobile
manufacturers. CCMC (Comit des Constructeurs du March Commun) was the forerunner organisation to ACEA.
In January 1996 the CCMC European Oil Sequences became obsolete and were replaced by the ACEA European Oil
Sequences. This is true for light duty engine oils as well as heavy duty engine oils. CCMC European Oil Sequences are
not supported any more by ACEA.
With the 2004 release of the ACEA European Oil Sequences the A and B categories have been combined to the
respective A/B categories. At the same time, a new set of categories has been introduced with the intention to create
specifications for engine oils being suitable for the latest and future aftertreatment systems for Gasoline and Diesel
engines. These categories are designated as Cx-categories.
For Heavy Duty Diesel engines, the CCMC Dx categories were replaced by the ACEA Ex categories as of 1 January 1996.
The CCMC Dx categories then became obsolete and are no longer supported by ACEA.
For Gasoline and Light Duty Diesel engines, see below:
Catalyst Compatible oils for
Gasoline and Diesel engines
with aftertreatment devices :
for Gasoline Engines
for Gasoline Engines:
CCMC GxCategories
ed
by
ACEA AxCategories
c
la
ep
for Gasoline and Diesel
Engines:
for Diesel Engines:
for Diesel Engines:
CCMC PDxCategories
ACEA Cx
Categories
ce
la
ep
by
ACEA BxCategories
obsolete
Specification
Replacement Date
01.1996
X= 1, 2, 3, 4 or 5 depending of categories
1996/2004
25.10.2004
ACEA Ax/Bx
Categories
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCES FOR SERVICE-FILL OILS
Dec. 2012
The ACEA 2012 European Oil Sequences for Service-fill Oils comprise 3 sets (classes) of sequences: one for Gasoline
and Light Duty Diesel engines; one specifically for Gasoline and Light Duty Diesel engines with after treatment devices
and one for Heavy Duty Diesel engines. Within each of these sets there are categories which reflect different performance
requirements - four (A1/B1, A3/B3, A3/B4 & A5/B5) for gasoline and light duty diesel engines; four (C1, C2, C3, C4)
specifically for engines with after treatment devices, and four (E4, E6, E7, E9) for heavy duty diesel engines. Typical
applications for each sequence are described below for guidance only. Specific applications of each sequence are the
responsibility of individual engine manufacturers for their own vehicles / engines.
The sequences define the minimum quality level of a product for self-certification to EELQMS and presentation to ACEA
members. Performance parameters other than those covered by the tests shown or more stringent limits may be indicated
by individual ACEA member companies.
NOMENCLATURE & ACEA PROCESS:
Each set of sequences is designated for consumer use by a 2 part code comprising a letter to define the CLASS (e.g. C),
and a number to define the CATEGORY (e.g. C1).
In addition, for industry use, each sequence has a two-digit number to identify the YEAR of implementation of that severity
level (e.g. A1 / B1-04).
The CLASS indicates oil intended for a general type of engine - currently A / B = gasoline and light duty diesel engines; C
= catalyst compatible oils for gasoline and diesel engines with after treatment devices. Other classes may be added in
future if, for example, Natural Gas engines prove to require oil characteristics which cannot readily be incorporated into
existing classes.
The CATEGORY indicates oils for different purposes or applications within that general class, related to some aspect or
aspects of the performance level of the oil. Typical applications for each sequence are described below for guidance only.
Specific applications of each sequence are the responsibility of the individual motor manufacturer for their own vehicles
and engines. Oils within a category may also meet the requirements of another category, but some engines may only be
satisfied by oils of one category within a class.
The YEAR numbers for ACEA Sequence is intended only for industry use and indicates the year of implementation of that
severity level for the particular category. A new year number will indicate, for example, that a new test, parameter or limit
has been incorporated in the category to meet new / upgraded performance requirements whilst remaining compatible
with existing applications. An update must always satisfy the applications of the previous issue. If this is not the case, then
a new category is required.
An administrative ISSUE Number is added for industry use where it is necessary to update the technical requirements of a
sequence without the intention to increase severity (e.g. when a CEC test engine is updated to the latest version whilst
maintaining equivalent severity; or where a severity shift in the test requires modification of the specified limits.).
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCES FOR SERVICE-FILL OILS
Dec. 2012
Where claims are made that Oil performance meets the requirements of the ACEA sequences (e.g. product literature,
packaging, labels) they must specify the ACEA Class and Category (see Nomenclature & ACEA Process for definitions).
Consumer Language:
A/B : gasoline and diesel engine oils
A1/B1 Stable, stay-in-grade oil intended for use at extended drain intervals in gasoline engines and car & light van diesel
engines specifically designed to be capable of using low friction low viscosity oils with a high temperature / high shear rate
viscosity of 2.6 mPa*s for xW/20 and 2.9 to 3.5 mPa.s for all other viscosity grades. These oils are unsuitable for use in
some engines. Consult owner manual or handbook if in doubt.
A3/B3 Stable, stay-in-grade oil intended for use in high performance gasoline engines and car & light van diesel engines
and/or for extended drain intervals where specified by the engine manufacturer, and/or for year-round use of low viscosity
oils, and/or for severe operating conditions as defined by the engine manufacturer.
A3/B4 Stable, stay-in-grade oil intended for use in high performance gasoline and direct injection diesel engines, but also
suitable for applications described under A3/B3.
A5/B5 Stable, stay-in-grade oil intended for use at extended drain intervals in high performance gasoline engines and car
& light van diesel engines designed to be capable of using low friction low viscosity oils with a High temperature / High
shear rate (HTHS) viscosity of 2.9 to 3.5 mPa.s. These oils are unsuitable for use in some engines. Consult owner manual
or handbook if in doubt.
C : Catalyst compatibility oils
Stable, stay-in-grade oil intended for use as catalyst compatible oil in vehicles with DPF and TWC in high
C1
performance car and light van diesel and gasoline engines requiring low friction, low viscosity, low SAPS oils with a
minimum HTHS viscosity of 2.9 mPa.s. These oils will increase the DPF and TWC life and maintain the vehicles fuel
economy.
Warning: these oils have the lowest SAPS limits and are unsuitable for use in some engines. Consult owner manual or
handbook if in doubt.
C2
Stable, stay-in-grade oil intended for use as catalyst compatible oil in vehicles with DPF and TWC in high
performance car and light van diesel and gasoline engines designed to be capable of using low friction, low viscosity oils
with a minimum HTHS viscosity of 2.9mPa.s. These oils will increase the DPF and TWC life and maintain the vehicles fuel
economy.
Warning: these oils are unsuitable for use in some engines. Consult owner manual or handbook if in doubt.
C3
Stable, stay-in-grade oil intended for use as catalyst compatible oil in vehicles with DPF and TWC in high
performance car and light van diesel and gasoline engines, with a minimum HTHS viscosity of 3.5mPa.s. These oils will
increase the DPF and TWC life.
Warning: these oils are unsuitable for use in some engines. Consult owner manual or handbook if in doubt.
Stable, stay-in-grade oil intended for use as catalyst compatible oil in vehicles with DPF and TWC in high
C4
performance car and light van diesel and gasoline engines requiring low SAPS oil with a minimum HTHS viscosity of
3.5mPa.s. These oils will increase the DPF and TWC life.
Warning: these oils are unsuitable for use in some engines. Consult owner manual or handbook if in doubt.
SAPS : Sulphated Ash, Phosphorus, Sulphur
DPF : Diesel Particulate Filter
TWC : Three way catalyst
HTHS : High temperature / High shear rate viscosity
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCES FOR SERVICE-FILL OILS
Dec. 2012
E : Heavy Duty Diesel engine oils
E4
Stable, stay-in-grade oil providing excellent control of piston cleanliness, wear, soot handling and lubricant stability.
It is recommended for highly rated diesel engines meeting Euro I, Euro II, Euro III, Euro IV and Euro V emission
requirements and running under very severe conditions, e.g. significantly extended oil drain intervals according to the
manufacturers recommendations. It is suitable for engines without particulate filters, and for some EGR engines and
some engines fitted with SCR NOx reduction systems. However, recommendations may differ between engine
manufacturers so Driver Manuals and/or Dealers shall be consulted if in doubt.
E6
Stable, stay-in-grade oil providing excellent control of piston cleanliness, wear, soot handling and lubricant stability.
It is recommended for highly rated diesel engines meeting Euro I, Euro II, Euro III, Euro IV, Euro V and Euro VI emission
requirements and running under very severe conditions, e.g. significantly extended oil drain intervals according to the
manufacturers recommendations. It is suitable for EGR engines, with or without particulate filters, and for engines fitted
with SCR NO x reduction systems. E6 quality is strongly recommended for engines fitted with particulate filters and is
designed for use in combination with low sulphur diesel fuel. However, recommendations may differ between engine
manufacturers so Driver Manuals and/or Dealers shall be consulted if in doubt.
E7
Stable, stay-in-grade oil providing effective control with respect to piston cleanliness and bore polishing. It further
provides excellent wear control, soot handling and lubricant stability. It is recommended for highly rated diesel engines
meeting Euro I, Euro II, Euro III, Euro IV and Euro V emission requirements and running under severe conditions, e.g.
extended oil drain intervals according to the manufacturers recommendations. It is suitable for engines without particulate
filters, and for most EGR engines and most engines fitted with SCR NOx reduction systems. However, recommendations
may differ between engine manufacturers so Driver Manuals and/or Dealers shall be consulted if in doubt.
E9
Stable, stay-in-grade oil providing effective control with respect to piston cleanliness and bore polishing. It further
provides excellent wear control, soot handling and lubricant stability. It is recommended for highly rated diesel engines
meeting Euro I, Euro II, Euro III, Euro IV, Euro V and Euro VI emission requirements and running under severe conditions,
e.g. extended oil drain intervals according to the manufacturers recommendations. It is suitable for engines with or without
particulate filters, and for most EGR engines and for most engines fitted with SCR NO x reduction systems. E9 is strongly
recommended for engines fitted with particulate filters and is designed for use in combination with low sulphur diesel fuel.
However, recommendations may differ between engine manufacturers so Drivers Manuals and/or Dealers should be
consulted if in doubt
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST METHOD
PROPERTIES
UNIT
LIMITS
A1 /
A3 /
A3 /
A5 /
B1-12
B3-12
B4-12
B5-12
1. LABORATORY TESTS
SAE J300
1.1
Viscosity
grades
CEC L -014-93
1.2 *
No restriction except as defined by shear stability and HT/HS
requirements. Manufacturers may indicate specific viscosity
requirements related to ambient temperature.
Latest active issue
100oC Viscosity after 30 cycles
mm2/s
xW-20 5.6
xW-30 9.3
xW-40 12.0
Viscosity at 150oC and
mPa.s
2.9
and 3.5;
xW-20:
2.6. min
or
Shear
stability
ASTM D6278
1.3
CEC L-036-90
Viscosity
at high temp. &
106 s-1 shear rate
high shear rate
Max. weight loss
after 1 h at 250oC
All grades to be stay in grade
3.5
and
3.5
1.4 Evaporative
loss
CEC L-040-93
(Noack)
1.5 TBN
ASTM D 2896
mgKOH/g
1.6 * Sulphur
ASTM D5185
% m/m
Report
1.7 * Phosphor
ASTM D5185
% m/m
Report
1.8 * Sulphated
ASTM D874
% m/m
%
13
8.0
1.3
8.0
1,0 and
1.5
1.6
1.10 *
ppm m/m
ASTM D6443
CEC L-039-96
after immersion for 7 days in fresh
compatibility
oil without pre-ageing
Hardness DIDC
Tensile strength
Elongation at rupture
Volume variation
1.11 Foaming
ASTM D892
tendency
without option A
1.12 High
temperature
foaming
tendency
1.13 * Oxidation
ASTM D6082
High
temperature
foam test
GFC-Lu-43A-11
in presence of
biodiesel
1.14 LowTemperature
Pumpability
CEC L-105
1.6
Elastomer type
RE1
RE2-99
RE3-04
RE4
DBL-AEM
-1/+5
-5/+8
-22/ +1
-5/+5
-5/+10
-40/+10
-15/+18
-30/+10
-20/+10
-35/ -
-50/+10
-35/+10
-20/+10
-50/+10
-50/ -
-1/+5
-7/+5
-1/+22
-5/+5
-5/+15
points
Tendency - stability
ml
Sequence I (24oC) 10 - nil
Sequence II (94oC) 50 - nil
Sequence III (24oC) 10 - nil
Tendency - stability
ml
Sequence IV (150oC) 100 nil
Catalysed ageing test until 144h
at 170C & with air bubbling:
1.
on pure oil
2.
with B10 added (B71 1892
GO B10 LUB)
PAI at 144h
Kin. viscosity @ 100C variation:
at 72h
at 96h
at 120h
at 144h
MRV
Yield stress
(MRV at SAE J300 temperatures
applicable for the fresh oil viscosity
grade)
8.0
Report
Max. variation of characteristics
Oil / elastomer
10.0
0,9 and
ash
1.9 Chlorine
2.9
Report
cSt & %
cSt & %
cSt & %
cSt & %
mPas
Pa
Acc to SAE
Acc to SAE
Report
Report
Report
Report and at
144h:
< +200% (no
solidification)
Acc to SAE
J300 for
J300 for
J300 for
fresh oil
fresh oil
fresh oil
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST METHOD
PROPERTIES
UNIT
LIMITS
A1 /
B1-12
A3 /
B3-12
A3 / B4-
A5 / B5-
12
12
2. ENGINE TESTS
2.1
High
CEC L-088-02
(TU5JP-L4)
Merit
9.0
Piston varnish
Merit
RL 216
(5 elements, average of 4 pistons)
temperature
deposits
Ring sticking (each part)
72 Hour test
mm2/s
0.8 x RL216
Oil consumption
kg/test
Report
Absolute viscosity increase at 40oC
Ring sticking
between min and max values during
Oil thickening
test
2.2 *
ASTM D6593-00
Average engine sludge
merit
7.8
Low
(Sequence VG)
Rocker cover sludge
merit
8.0
temperature
Under protocol
Average Piston skirt varnish
merit
7.5
sludge
& requirements
Average engine varnish
merit
8.9
for API
Comp. ring (hot stuck)
none
Oil screen clogging
20
Cam wear, average
10
Cam wear, max.
15
scuffing wear
Pad merit (Ave. of 8 pads)
merit
7.5
2.4 * Black
Engine sludge, average
merit
RL 140 + 4
CEC L-054-96
Fuel economy improvement vs.
(M111)
Reference oil RL191 (15W-40)
CEC L-093-04
(DV4TD)
To be replaced
by DV6C
Absolute viscosity increase at
2.3
Valve train
CEC L-038-94
(TU3M)
sludge
2.5 *
Fuel economy
2.6 Medium
temperature
dispersivity
2.7 * Oil
Dispersion at
Medium
Temperature
for Passenger
Car Direct
Injection Diesel
Engines
2.8 * Wear
CEC L-106
(DV6C)
CEC L099-08
(OM646LA)
2.5
2.5
--
0.60 x RL223 result
mm2/s
100oC and 6 % soot
(RL223 2,5pts )
merit
Piston merit
Absolute viscosity increase at
limits to defined
100oC and 6 % soot
mm2/s
Piston merit
merit
Cam wear outlet (avg. max. wear 8 cams)
120
140
120
Cam wear inlet (avg. max. wear 8 c.)
100
110
100
Cylinder wear (avg. 4 cyl.)
5.0
5.0
5.0
Bore polishing (13 mm) - max. value
3.0
3.5
3.0
report
report
report
report
report
report
merits
report
report
12
merits
report
report
8,8
of 4 cylinders
Tappet wear inlet (avg. max. wear 8 cams)
Tappet wear outlet (avg. max. wear 8cams)
Piston cleanliness (avg. 4 pistons)
Engine sludge avg.
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST METHOD
2. ENGINE TESTS CONTINUED
CEC L-078-99
2.9 *
DI diesel
PROPERTIES
Piston cleanliness
UNIT
merit
LIMITS
A1 /
B1-12
A3 /
B3-12
A3 /
B4-12
A5 /
B5-12
RL206
RL206
RL206
RL206
(VW TDI)
minus
4 points
Piston
Ring sticking (Rings 1 & 2)
cleanliness &
Ring sticking
Average of all 8 rings
ASF
1.0
1.2
1.0
1.0
Max. for any 1st ring
ASF
1.0
2.5
1.0
1.0
Max. for any 2nd ring
ASF
0.0
0.0
0.0
0.0
EOT TBN (ISO 3771)
EOT TAN (ASTM D 664)
mgKOH/g
4.0
4.0
6.0
4.0
Report
Report
Report
Report
Piston Cleanliness
Merits
Report
Effects of
Ring Sticking
ASF
Report
Biodiesel
Sludge
Merits
Report
2.10 *
CEC L-104
mgKOH/g
*: Additional information is given as footnotes underneath the table for the C-categories, page 12.
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES WITH AFTER TREATMENT DEVICES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST METHOD
PROPERTIES
UNIT
LIMITS
C1-12
C2-12
C3-12
C4-12
1. 1. LABORATORY TESTS
SAE J300
1.1
Viscosity
grades
1.2* Shear
stability
No restriction except as defined by shear stability and HT/HS
requirements. Manufacturers may indicate specific viscosity
requirements related to ambient temperature.
Latest active issue
CEC L-014-93
100oC Viscosity after 30 cycles
mm2/s
Viscosity at 150oC and
mPa.s
All grades to be stay in grade
or
ASTM D6278
1.3 Viscosity
at high temp. &
high shear rate
CEC L-036-90
1.4 Evaporative
CEC L-040-93
3.5
106 s-1 shear rate
(Noack)
loss
2.9
Max. weight loss
13
11
after 1 h at 250oC
6.0
1.5 TBN
ASTM D 2896
mg KOH / g
1.6 * Sulphur
ASTM D5185
% m/m
0.2
1.7 * Phosphorus
ASTM D5185
% m/m
0.05
1.8 * Sulphated
ASTM D874
% m/m
0.5
1.9 Chlorine
ASTM D6443
ppm m/m
1.10 *
CEC L-039-96
0.3
0.2
0.070
0.090
0.090
0.090
0.8
0.5
ash
Oil / elastomer
after immersion for 7 days in fresh
compatibility
oil without pre-ageing
Hardness DIDC
Tensile strength
Elongation at rupture
Volume variation
1.11
Foaming
ASTM D892
tendency
without option A
1.12
High
temperature
foaming
tendency
1.13 * Oxidation
Report
Max. variation of characteristics
Elastomer type
RE1
RE2-99
RE3-04
RE4
-1/+5
-5/+8
-22/ +1
-5/+5
-5/+10
-40/+10
-15/+18
-30/+10
-20/+10
-35/ -
-50/+10
-35/+10
-20/+10
-50/+10
-50/ -
-5/+5
-5/+15
points
-1/+5
-7/+5
-1/+22
Tendency - stability
ml
Sequence I (24oC) 10 - nil
Sequence II (94oC) 50 - nil
Sequence III (24oC) 10 - nil
ASTM D6082
High temperature
foam test
Tendency - stability
ml
Sequence IV (150oC) 100 nil
GFC-Lu-43A-11
Catalysed ageing test until 144h
at 170C & with air bubbling:
1.
on pure oil
2.
with B10 added (B71
1892 GO B10 LUB)
in presence of
biodiesel
DBL-AEM
Report
PAI at 144h
Kin. viscosity @ 100C variation:
at 72h
at 96h
at 120h
at 144h
MRV
Temperature
Yield stress
Pa
Pumpability
(MRV at SAE J300 temperatures
applicable for the fresh oil viscosity
grade)
1.14 Low-
CEC L-105
cSt & %
cSt & %
cSt & %
cSt & %
mPas
Report
Report
Report
Report and at 144h: < +200% (no solidification)
Acc to SAE
J300 for fresh oil
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES WITH AFTER TREATMENT DEVICES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST
METHOD
PROPERTIES
UNIT
LIMITS
C1-12
C2-12
C3-12
C4-12
2. ENGINE TESTS
2.1
High
temperature
CEC L-088-T02
(TU5JP-L4)
deposits
Ring sticking
72 Hour test
Oil thickening
Ring sticking (each part)
Merit
9.0
Piston varnish
(5 elements, average of 4 pistons)
Merit
RL 216
Absolute viscosity increase at 40oC
between min and max values
during test
Oil consumption
mm2/s
0.8 x RL216
Report
7.8
ASTM D659300
(Sequence
VG)
Under protocol
&
requirements
for API
Average engine sludge
kg/test
merit
Rocker cover sludge
merit
8.0
Average Piston skirt varnish
merit
7.5
Average engine varnish
merit
8.9
Oil screen clogging
20
CEC L-038-94
Cam wear, average
10
Cam wear, max.
15
scuffing wear
Pad merit (Ave. of 8 pads)
merit
7.5
2.4 *
Engine sludge, average
merit
RL 140 + 4
2.2 *
Low
temperature
sludge
2.3
Valve train
(TU3M)
Comp. ring (hot stuck)
none
Black sludge
2.5 * Fuel
CEC L-54-96
Fuel economy improvement vs.
economy
(M111)
Reference oil RL191 (15W-40)
CEC L-093-04
(DV4TD)
To be
replaced by
DV6
CEC L-106
Absolute viscosity increase at
2.6 Medium
temperature
dispersivity
2.7 * Oil
Dispersion at
Medium
Temperature
for Passenger
Car Direct
Injection
Diesel
Engines
(DV6C)
3.0
2.5
1.0 (for Xw30 grades)
mm/s
0.60 x RL223 result
merit
(RL223 2,5pts )
mm/s
limits to defined
100oC and 6 % soot
Piston merit
Absolute viscosity increase at
100oC and 6 % soot
Piston merit
merit
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
GASOLINE and DIESEL ENGINES WITH AFTER TREATMENT DEVICES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENT
TEST
METHOD
PROPERTIES
UNIT
LIMITS
C1-12
C2-12
C3-12
C4-12
2. ENGINE TESTS CONTINUED
2.8 * Wear
CEC L-099-08
(OM646LA)
Cam wear outlet (avg. max. wear 8 cams)
120
120
120
Cam wear inlet (avg. max. wear 8 c.)
100
report
100
Cylinder wear (avg. 4 cyl.)
5.0
5.0
5.0
Bore polishing (13 mm) - max. value
3.0
3.0
3.0
report
report
report
report
report
report
merits
report
report
12
merits
report
report
8,8
merit
RL206
RL206
RL206
ASF
1.0
1.2
1.0
ring
ASF
1.0
2.5
1.0
Max. for any 2nd ring
ASF
of 4 cylinders
Tappet wear inlet (avg. max. wear 8cams)
Tappet wear outlet (avg. max. wear 8cams)
Piston cleanliness (avg. 4 pistons)
Engine sludge avg.
CEC L-078-99
2.9 *
DI diesel
Piston cleanliness
(VW TDI)
Ring sticking (Rings 1 & 2)
Piston
Average of all 8 rings
cleanliness &
st
Max. for any 1
Ring sticking
EOT TBN (ISO 3771)
EOT TAN (ASTM D 664)
0.0
0.0
0.0
report
report
report
report
report
report
Piston Cleanliness
Merits
Report
Effects of
Ring Sticking
ASF
Report
Biodiesel
Sludge
Merits
Report
2.10 *
CEC L-104
mgKO
H/g
*: Footnotes referring to the following requirements in the A/B- and C-Classes:
No. 1.2
The minimum viscosity for xW-20 oils after shearing is 5,6 cSt.
No. 1.6;1.7;1.8 Maximum limits, Values take into account method and production tolerances
No. 1.6;1.7
Internal standard method has to be used.
No. 1.10
All reference materials and limits for RE1, RE2, RE3, RE4 and DBL-AEM can be used until acceptable new reference materials
(proposed from CEC L-039-96) are available and appropriate limits have been set. The Daimler requirements for DBL-AEM D
8948/200 are VDA 675301, 7 days 2h, 150C 2C, closed cup test.
RE-1, RE-2, RE-3, RE-4 based on CEC and DBL-AEM based on Daimler AG data may continue to be used grandfathered for the
lifetime of the ACEA 2012 sequences.
No. 1.13
Until a CEC Test Method is developed, the oxidation behavior of engine oil formulations must be proved by GFC-Lu-43A-11. Test
results obtained by this procedure will be accepted under the condition that they come from labs having participated to the official
round robin and comply with the quality criteria of GFC.
No. 2.2
The limits shown are based on those applied in U.S. market requirements. ACEA will continuously review the situation to ensure
that these limits are appropriate for European vehicles and lubricants.
No. 2.4
Until a new CEC Test Method is developed, the gasoline sludge protection performance of engine oil formulations must be proved
by the M 271 sludge test procedure as described by Daimler AG. Test results obtained by the M 271 procedure will be accepted
under the condition that they come from test rigs being referenced and quality controlled by Daimler AG. Limits are based on the
same reference oil as with the old M111 sludge test.
No. 2.5
ACEA considers the CEC L-54-T-96 test the only valid comparator against which claims of lubricant fuel economy improvement
should be made.
No. 2.7
May be performed as soon as it becomes available as an alternative to the DV4 test. ACEA will decide when the DV4 test will be
finally deleted from this specification. CEC-L-093-04 (DV4 Test) test results obtained in accordance with the ATIEL guidelines may
be used by a grandfathering process also after this test has become unavailable to run and is replaced by the CEC-L-106 (DV6
Test) procedure.
No. 2.8
Not all parameters are yet official CEC parameters. C2 limit for inlet cam wear under definition.
No. 2.9
Test report has to give measured values before & after the test, all measurements to be taken in the same lab. Note: TAN is
considered to become performance criteria in the future. Not all parameters are yet official CEC parameters.
No. 2.10
Test is still under development at the time of publishing of this specification. Test has to be performed for all qualifications against
2012 Oil Sequences from the time the test is officially released by CEC (running programs only). All test criteria is rate and report.
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
HEAVY DUTY DIESEL ENGINES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENTS
TEST METHOD
PROPERTIES
UNIT
LIMITS
E4-12
E6-12
E7-12
E9-12
1. LABORATORY TESTS
SAE J300
1.1 Viscosity
No restriction except as defined by shear stability and HT/HS
requirements. Manufacturers may indicate specific viscosity
Latest Active Issue
1.2 Shear stability
CEC L-014-93
or
ASTM D6278
ASTM D6278
Viscosity after 30 cycles
measured at 100oC.
Viscosity after 90 cycles
measured at 100oC
1.3 Viscosity
CEC L-036-90
High Temperature
requirements related to ambient temperature.
mm2/s
Stay in grade
mm2/s
Stay in grade
Viscosity at 150oC and
106 s-1 Shear rate
mPa.s
Max. weight loss
3.5
High Shear Rate
1.4 Evaporative
Loss
CEC L-040-93
(Noack)
13
after 1 h at 250oC
1.5 Sulphated Ash
ASTM D874
% m/m
1.6 * Phosphorus
ASTM D5185
% m/m
0.08
0.12
1.7 * Sulphur
ASTM D5185
% m/m
0.3
0.4
1.8 * Oil Elastomer
CEC L-039-96
Max. variation of
characteristics after
Compatibility
2.0
1.0
2.0
1.0
Elastomer
type
RE1
RE2-99
RE3-04
RE4
DBL-AEM
-1/+5
-5/+8
-25/+1
-5/+5
-5/+10
immersion for 7 days in
fresh oil without pre-ageing
1.9 Foaming
Tendency
ASTM D892
Hardness DIDC
points
Tensile strength
-50/+10
-15/+18
-45/+10
-20/+10
-35/ -
Elongation rupture
-60/+10
-35/+10
-20/+10
-50/+10
-50/ -
Volume variation
-1/+5
-7/+5
-1/+30
-5/+5
-5/+15
Tendency stability
ml
without option A
ml
ml
1.10 High temperature
Sequence I (24oC) 10 nil
Seq I 10/0
Sequence II (94oC) 50 nil
Seq II 20/0
Seq III 10/0
Sequence III (24oC) 10 nil
ASTM D6082
Tendency - stability
ml
Sequence IV (150oC) 200-50
CEC L-085-99
Oxidation induction time
min
R&R
Copper increase
ppm
R&R
R&R
20
Lead increase
ppm
R&R
100
100
Copper strip rating
max
R&R
R&R
foaming tendency
1.11 Oxidation
65
(PDSC)
1.12 Corrosion
1.13 * TBN
ASTM D 6594
ASTM D2896
mg
12
KOH/g
1.14 Low temperature
pumpability
CEC L-105
MRV
mPas
Yield stress
Pa
(MRV at SAE J300
temperatures applicable for
the fresh oil viscosity grade)
Acc to SAE
J300 for fresh oil
ACEA
ACEA 2012 EUROPEAN OIL SEQUENCE FOR SERVICE-FILL OILS FOR
HEAVY DUTY DIESEL ENGINES
Dec. 2012
This sequence defines the minimum quality level of a product for self-certification to EELQMS and for presentation to ACEA members.
Performance parameters other than those covered by the tests shown or more stringent limits may be indicated by individual member companies.
REQUIREMENTS
TEST METHOD
PROPERTIES
UNIT
LIMITS
E4-12
E6-12
E7-12
E9-12
140
140
155
155
2.1/2.2/2.3
2.1/2.2/2.3
2.1/2.2/2.3
2. ENGINE TESTS
2.1 * Wear
CEC L-099-08
(OM646LA)
2.2 * Soot in oil
ASTM D 5967
(Mack T-8E)
Cam wear outlet
(avg. max. wear 8 cams)
Test duration 300 h
Relative viscosity at 4.8% soot
and 50% shear loss
1 test/2 test/3 test average
2.3 Soot in oil
Mack T11
2.4 * Bore
CEC L-101-08
polishing
(OM501LA)
Piston Cleanliness
2.5 * Soot induced
Cummins ISM
Min TGA soot @ 4.0 cSt (100C)
3.5/3.4/3.3
Min TGA soot @ 12.0 cSt (100C)
6.0/5.9/5.9
Min TGA soot @ 15.0 cSt (100C)
6.7/6.6/6.5
Bore polishing, average
1.0
1.0
2.0
2.0
Piston Cleanliness, average
merit
26
26
17
17
Oil consumption
kg/test
Engine sludge, average
Merit
R&R
R&R
R&R
R&R
1000
Merit
Rocker pad average weight
wear
loss at 3.9 % soot
mg
7.5/7.8/7.9
7.1
kPa
55/67/74
19
merit
8.1/8.0/8.0
8.7
1 test/2 test/3 test average
Oil filter diff.press @ 150h
1 test/ 2 test/3 test average
Engine sludge
1 test/2 test/3 test average
Adj. screw weight loss
2.6 * Wear (linerring-bearings)
Mack T12
mg
49
1000
1000
1000
26
26
24
mg
117
117
105
End of test lead
ppm
42
42
35
Delta lead 250-300 hrs
ppm
18
18
15
Oil consumption (Phase II)
g/hr
95
95
85
Merit
Avg.liner wear
Average top ring weight loss
*: Footnotes referring to the following requirements in the E-Class:
No. 1.6;1.7
Internal standard method has to be used.
No. 1.8
All reference materials and limits for RE1, RE2, RE3, RE4 and DBL-AEM can be used until acceptable new reference materials
(proposed from CEC L-039-96) are available and appropriate limits have been set. The Daimler requirements for DBL-AEM D
8948/200 are VDA 675301, 7 days 2h, 150C 2C, closed cup test.
RE-1, RE-2, RE-3, RE-4 based on CEC and DBL-AEM based on Daimler AG data may continue to be used grandfathered for the
lifetime of the ACEA 2012 sequences.
No. 1.13
For E7, values < 9.00 are not accepted.
No. 2.1
OM602A data can be used instead of OM646LA data providing it meets the requirements as specified in the 2007 ACEA
sequences.
Additional parameters may be included once approved by CEC.
No. 2.2
Mack T11 results obtained as part of an API CI-4, CI-4 plus or API CJ-4 approval program, can be used in place of Mack T8E.
No. 2.4
Bore polish, oil consumption and engine sludge are non-approved CEC parameters.
OM441LA data can be used instead of OM501LA data providing it meets the requirements as specified in the 2007 ACEA
sequences.
No. 2.5
For E7 results from M11HST (ASTM D6838), at API CH-4, or M11EGR (ASTM D6975), at API CI-4 or CI-4 Plus, can be used in
place of Cummins ISM. Merit number shall be calculated according to the API CI-4 specification
No. 2.6
For E6 & E7 merit number shall be calculated according to the API CI-4 specification.
For E6 & E7 Mack T10 results obtained as part of an API CI-4 or CI-4 plus approval program, can be used in place of Mack T12.
