HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 1 of 19
D3
HENDIJAN OFFSHORE COMPLEX DEVELOPMENT PROJECT
Design and Engineering Subcontract
Subcontract No.: MKT49-OFF/JAMM-01-01/08
TELECOMMUNICATION PHILOSOPHY
Document Class: 1
D3
22-Jan-2009
Final Issue (For Construction)
ZKZ
RRG
MSG
D2
28-Dec-2008
Issued For Approval (IFA)
ZKZ
RRG
MSG
D1
13-Dec-2008
ISSUED FOR COMMENTS (IFC)
ZKZ
RRG
MSG
D0
2-Dec-2008
Interdisciplinary Check (IDC)
ZKZ
RRG
MSG
B3
07/10/08
APPROVED FOR DESIGN (AFD)
ILM
TB
PMM
B2
29/8/08
ISSUED FOR COMMENTS (IFC)
ILM
TB
PMM
B1
22/8/08
INTER-DISCIPLINE CHECK (IDC)
ILM
TB
PMM
B0
19/8/08
DISCPILINE INTERNAL CHECK
ILM
TB
PMM
Rev.
Date
Description
Prep.
Check.
Approv.
ENG. SUB-CONTRACTOR
Approv.
Approv.
CONT.
COMP.
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
Rev.
GOXX 2900
Page: 2 of 19
D3
TABULATION OF REVISED PAGES
Revisions
Revisions
Sheet
D0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Revisions
Sheet
D1
D2
D3
D4
D5
Sheet
D0
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
D1
D2
D3
D4
D5
D0
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
D1
D2
D3
D4
D5
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 3 of 19
D3
Table of content
APPENDIXES..........................................................................................................................................................4
APPENDIX 1: TYPICAL SCHEMATIC FOR TELECOM VENDOR'S SCOPE ......................................................4
1
INTRODUCTION ..............................................................................................................................................5
DEFINITIONS AND ABBREVIATIONS ...........................................................................................................6
SCOPE OF WORK...........................................................................................................................................7
3.1
Bahregansar ...............................................................................................................................................7
3.2
Satellite Platform Facilities .........................................................................................................................7
3.2.1
Central platform................................................................................................................................................7
3.2.2
Platform Facilities (WHP-7& WHP-8).............................................................................................................8
CODES, STANDARDS AND RECOMMENDED PRACTICES .......................................................................9
4.1
Mandatory Requirements ...........................................................................................................................9
4.2
Standards, Codes and Recommendations.................................................................................................9
4.3
Associated Project Reference documents ...............................................................................................10
ENVIRONMENTAL PROTECTION ...............................................................................................................10
5.1
Outdoor conditions....................................................................................................................................10
5.2
Indoor conditions ......................................................................................................................................11
PHILOSOPHY OVERVIEW ...........................................................................................................................11
6.1
Basic Objectives .......................................................................................................................................11
6.2
Operational Considerations ......................................................................................................................12
6.3
Communication Links ...............................................................................................................................12
6.4
Fiber Optic Network ..................................................................................................................................13
COMMUNICATION EQUIPMENT SPECIFICATIONS ..................................................................................14
7.1
Telephones ...............................................................................................................................................14
7.2
Telephone To Ethernet Extender .............................................................................................................15
7.3
CCTV Cameras and DVR/CODEC...........................................................................................................15
7.4
Self Healing Multi-Drop Multiplexer ..........................................................................................................16
COMMUNICATION POWER SUPPLY ..........................................................................................................17
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 4 of 19
D3
SYSTEM INTERFACE REQUIREMENTS .....................................................................................................17
9.1
PABX Interface .........................................................................................................................................17
9.2
Ethernet Interface .....................................................................................................................................17
10
EQUIPMENT PROTECTION....................................................................................................................17
11
JUNCTION BOX & CABLING .................................................................................................................17
12
EARTHING ...............................................................................................................................................18
APPENDIXES
APPENDIX 1: TYPICAL SCHEMATIC FOR TELECOM VENDOR'S SCOPE
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 5 of 19
D3
INTRODUCTION
The Hendijan Field is located in the North-west section of the Persian Gulf. It is about 10km
North-east of Bahregansar, 34km South-west of Tangu and 42km South-west of Rag-e-Sefid
fields.
Hendijan field is an anticlinal structure with a fault at the west flank and is separated from
close by Bahregansar field by a geophysically identified saddle. The dimension of Hendijan
field is about 11 km in length and 5 km in width. The field was discovered by drilling of well
HD-01 in 1968 by AGIP Oil Company. Following drilling of 4 more wells proved the presence
of oil in Ghar, Asmari, Sarvak and Nahr Umr reservoirs.
Iranian Offshore Oil Company (IOOC) has a program to develop the field which will allow the
increase in oil production. This program will include new installations of two unmanned
wellhead platforms (WHP7 and WHP8) and a Manifold Platform with all necessary equipment
and flow lines as follows:
i)
One platform with ten slots for drilling of one description well and six development
wells at X = 376526E, Y = 3324332 N in UTM (WGS-1984) system (WHP7 Wellhead
Platform).
ii)
One platform with ten slots for drilling of four development wells at X = 376140 E, Y =
3322200 N in UTM (WGS-1984) system (WHP8 Wellhead Platform).
iii)
One Manifold Platform (MP) to receive the two 12 pipelines from wellhead platforms.
Manifold Platform is a one-level receiving facility platform bridge-connected to the Central
Hendijan production platform.
iv)
Two 12" pipelines, one from each wellhead platform to transport the raw offshore
production to the Central Hendijan production platform via the new Manifold Platform (MP).
v)
Electrical power cables from Bahregansar to each wellhead platform and Central
Hendijan platform with fibre optic for communication. There will be a power network between
Central Hendijan platform, Bahregansar Complex, WHP7 and WHP8 platforms (Ring
Topology). This will allow power to be supplied from alternative links in case one of the links
has been disconnected.
Reservoir fluids from the Hendijan Field flows to the Central Hendijan production platform in
multiphase flow lines. On the Central Hendijan production platform, the reservoir fluids are
gathered and exported to the existing Bahregansar old production platform for further
processing through existing 12 and 10 pipelines. In the existing Bahregansar production
platform, a production separator is provided for the separation of oil, water and gas.
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 6 of 19
D3
IOOC has awarded an EPC Contract to Iran Shipbuilding and Offshore Industries Complex Co
(ISOICO) to execute the project. ISOICO has awarded Jamm Design and Development
Company (JDD) a Subcontract to carry out the Basic & Detailed Design of the project . JDD
entered into a contract with Aker Engineering Malaysia Sdn Bhd (AEM) for the latter to
execute the Basic Engineering and Detail Design Endorsement for project. After conclusion of
Basic Design, this document is part of Detailed Design being carried out by JDD.
2
DEFINITIONS AND ABBREVIATIONS
COMPANY
Iranian Offshore Oil Company (IOOC)
API
American Petroleum Institute
CCTV
losed Circuit Television
IEC
International Electro-technical Commission
PABX
Private Automatic Branch Exchange
PC
Personal Computer
PLC
Programmable Logic Controller
SDS
Shutdown System
SDV
Shutdown Valve
TV
TechnischerUberwachungsVerein (German Technical Inspectorate)
LAN
Local Area Network
LTR
Local Technical Room
UPS
Uninterruptible Power Supply
VDU
Video Display Unit
USB
Universal Serial Bus
VGA
Video Graphic Adaptor
NMS
Network Management System
PP
Process Platform
MP
Manifold Platform
LQ
Living Quarters
MWP
Multi Wellhead Platform
HVAC
Heating Ventilation and Air Conditioning
CH
Central Hendijan
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
3
3.1
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
FOC
Fiber Optic Cable
ICSS
Integrated Control and Safety System
ITU
International Telecommunication Union
TCP
Transmission Control Protocol
IP
Internet Protocol
Rev.
Page: 7 of 19
D3
SCOPE OF WORK
Bahregansar
Bahregansar is the processing platform for Bahregansar & Hendijan Oil Fields. The production
from all the wellhead platform facilities is sent via sub sea pipeline to this platform.
Bahregansar platform consist of a new production platform(New PP), an old production
platform (old PP), a manifold platform (MP) which is used as bridge support and located
between new and old PPs, two living quarter (LQ) and a multi well head platform (MWP).
A new power Substation/technical room shall be built in MP to handle 3KV power distribution
and transfer it from Bahregansar to central Hendijan, WHP-7 and WHP-8 platforms via sub sea
cables. All safety devices and their accessories in this substation shall be connected to existing
ESD/F&G system (consist of Hima H51 PLC, Sieger Gas detection system & AutroSafe model
of Autronuca for fire detection system) in new PP control room. All required hardware and
software modification in existing system shall be done by contractor of this project. These
modifications shall not have improper effect on performance of existing system.
Remote control and monitoring of Hendijan satellite platforms shall be possible by two new
operating stations which will be installed in new PP control room and communicated to
satellite platform control systems through fiber optic cables.
3.2
Satellite Platform Facilities
All the satellite platforms are design for unmanned basis and no living quarters will be
provided.
3.2.1
Central platform
The current safety and instrumentation devices of existing Hendijan platform are mainly in a
very poor state of repair, inhibited and obsolete so shall be replaced, further more there is a
new electronic local control panel which is used as control and safety system for new installed
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 8 of 19
D3
test separator and pig launcher. This panel shall be connected to the ICSS for monitoring all
signals on operating work station.
This satellite platform shall be completed with the following facilities:
3.2.2
(1)
Fire Water
(2)
Local Technical Room (LTR)
(3)
Transformer (11KV/400V)
(4)
Pig Receiver System
(5)
Integrated Control & safety System (ICSS) consisting of PCS, ESD & F&G systems
(6)
HVAC (At LTR)
(7)
Chemical Injection
Platform Facilities (WHP-7& WHP-8)
These satellite wellhead platforms shall be completed with the following facilities:
(1)
Production Wells
(2)
Production and test manifold
(3)
Fire Water / Sprinkler System
(4)
Local Technical Room (LTR)
(5)
Transformer (11KV/400V)
(6)
Test separator
(7)
Drain system
(8)
Pig Launcher System
(9)
Integrated Control & safety System (ICSS) consisting of PCS, ESD & F&G systems
(10)
Wellhead Safety Cabinet (WHSC)
(11)
HVAC (At LTR)
(12)
Chemical Injection
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
4
4.1
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 9 of 19
D3
CODES, STANDARDS AND RECOMMENDED PRACTICES
Mandatory Requirements
The Telecommunications facilities shall comply with all the applicable Iranian Statutory and
Mandatory requirements applicable to offshore installations is carried out. In addition to any
such statutory provisions, the Telecommunication design should comply with all other Iranian
and international standards and codes of practice.
4.2
Standards, Codes and Recommendations
The communication equipment and systems should conform to all the relevant requirements
stated in the following Standards, Codes and Recommendations. The latest edition of codes and
standards listed below shall be used:
API 14F
Design and Installation of Electrical System for Offshore Production
Platform
BS 4992
Guide for Protection Against Ignition and Deterioration Initiated By
Radio Frequencies
IEC 60331
Fire Resistant Characteristics of Electrical Cables
IEC 60332
Test On Electrical Cables under Fire Conditions
IEC 60079 (all parts)
Electrical Apparatus for Explosive Gas Atmospheres
IEC 60529
Degrees of Protection Provided by Enclosures (IP Code)
IEC 60801
Electromagnetic Compatibility for Industrial Process Measurement and
Control Equipment (Part 2, 3 and 4)
IEC 61508
Examples of Methods for the Determination Of Safety Integrity Level
(Part5)
EN 50081-2
Radio Frequency Immunity Requirements
EN 50083-2
Radio Frequency Immunity Requirements
IEC TR 61000
Electro Magnetic Compatibility (EMC)
EN 300 386
Electromagnetic Compatibility And Radio Spectrum Matters (ERM);
Telecommunication
Network
Equipment;
Electromagnetic
Compatibility (EMC) Requirements
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 10 of 19
D3
EN 300 338
VHF Radio Installation Capable Of Transmitting and Receiving DSC and
Radiotelephony
ISO 1000
SI Units And Recommendation For Use Of Their Multiples And Of Certain
Other Units
ISO 9001:2000
Quality Management Systems Requirements
ITU-R
Related Recommendations and Reports
TU-T
Related Manuals and Recommendations
Where these conflict with Iranian Statutory and Mandatory requirements then the Iranian
Statutory and Mandatory requirements shall have precedence.
4.3
Associated Project Reference documents
HN-EIN-DB-GOXX-2800
Instrument Design Basis
HN-EIN-BD-GOXX-2830
Overall Control & Safety Block Diagram
HN-ETE-SP-GOXX-2901
Telecommunication Equipment Specification
HN-ETE-BD-GOXX-2920
Overall Telecommunication System Block Diagram
ENVIRONMENTAL PROTECTION
The ingress protection according to IEC-60529 for instrumentation equipment shall be as
minimum:
IP42: Equipment installed indoors (in enclosed buildings) and equipment located inside
enclosure hoods
IP65: All Field Instrumentation
5.1
Outdoor conditions
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
-Max.
Ambient
Temperature.
5.2
Design
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 11 of 19
D3
43 C
- Expected Extreme Temperature
49 C
- Min.Ambient Temperature.
7 C
- Max. Relative Humidity
100 %
- Min. Relative Humidity
50 %
Indoor conditions
Local Technical Room (LTR) will be air-conditioned. However, the platforms are required to
continue to operate without failure, without error and without incurring in long or short-term
damage to the equipment when the HVAC is out of commission.
All electric/electronic equipment within LTR must operate satisfactorily in an air-conditioned
environment, which will be maintained at the following conditions: 23C +/-2 C and 50% +/10% Relative Humidity
The systems shall continue to operate in HVAC upset conditions, when the temperature can fall
to 7 C or rise to 49 C and the humidity is up to 100%.
6
6.1
PHILOSOPHY OVERVIEW
Basic Objectives
The primary objective in the design of the telecommunication systems to serve the additional
and expanded offshore facilities is to provide highly reliable systems, which will meet all
functional and safety requirements. The design principles, which follow, are intended to
consolidate and standardize telecommunication system supply, including contractor and vendor
services, to achieve minimum capital and operating costs. The implementation of
telecommunication systems with high availability shall ensure safety objectives are met and
will contribute to the continuous uninterrupted production of oil and gas from offshore to
onshore facilities.
From a control and field management perspective, the new wellhead platforms will be
independent from Bahregansar platform. There will however, be important operational and
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 12 of 19
D3
control interaction between the platforms and therefore special emphasis will be placed on the
integrity of the interconnecting links between the platforms.
6.2
Operational Considerations
The new facilities on the wellhead platforms shall be equipped with the same level of service
provision as currently provided for the Bahregansar central platform. For the new facilities, all
telecommunication shall be of a modern, proven and reliable design.
The new facilities will be controlled and managed from Bahregansar control room and at this
location telecommunication access and control positions will be provided to serve the new
facility.
The means of communication between Bahregansar and new wellhead platforms shall be, by
sub-sea combined fiber optics and power cable, which will act as the medium to interconnect
the existing PABX from Bahregansar to each wellhead platform and also support the control
systems LAN network.
The communication between Bahregansar Central Control Room and its wellhead platforms
(including WHP-7, WHP-8 and existing Central Hendijan) will employ an integrated power
and communication submarine cable.
Optical fibers will be provided for both general communication and control and safety system
specific communication.
The sub-sea cable will be terminated at the Fiber Optic Patch Panel located in the Local
Technical Room (LTR) on each platform via a splitter box located at cellar deck. The supply,
installation and termination of the sub-sea cable shall be by the Contractor.
6.3
Communication Links
All platforms of the Hendijan Field shall be integrated to one ring network through several
communication links, with Bahregansar Central platform as the main platform. All
communication to shore will be linked to the existing VSAT satellite communication system
located on Bahregansar central platform. Communication between the unmanned wellhead
platforms and the Bahregansar Control Room shall be via telemetry systems (fiber optic
communication). These links shall be used to carry instrument signals, control signals and
alarms.
The following communication links are envisaged:
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
Rev.
GOXX 2900
D3
Location
Link to
Bahregansar
Central MP
Hendijan WHP-7 Sub-sea F.O
Approximately 15 km
Hendijan WHP-7
Hendijan Central Sub-sea F.O
CH-MP
Approximately 4 km
Hendijan
CH-MP
Hendijan WHP-8 Sub-sea F.O
Approximately 3 km
Bahregansar
Central MP
Approximately 13 km
Central
Hendijan WHP-8
Type
Page: 13 of 19
Sub-sea F.O
Distance (Note:1)
Note: 1: The distances indicated here are preliminary and as per preliminary report of
Geophysical Site and Route Survey GP-ISO-0279 Vol. 1 to 3 Rev. A.
The link equipment racks will be installed in the Local Technical Rooms (LTR) of the different
locations. A Fiber Optic Cable (FOC) as part of a sub-sea power/optic cable will be installed
between all above platforms. The links will be used for data, voice and video communication
and for process control / Safety data of the ICSS systems between the platforms.
6.4
Fiber Optic Network
The fiber optic network shall have the ring topology with the ability to heal itself in case of any
failure in each part of the network. As it has been shown in the overall control & safety
diagram, HN-EIN-BD-GOXX-2830, this network will carry all control and safety information
to the Bahregansar Control room, and also shall facilitate voice and video communication
between new remote wellhead platforms and Bahrgansar Central control room.
As part of the telecommunication system and control system in the Hendijan field a fiber optic
link, comprising a sub-sea power and optic cable, fiber junction boxes, fiber patch panels, and
media converters, shall be installed.
The fiber optic link will facilitate voice, video and data communication between platforms. The
fiber optic system will be connected to Drop/Insert Multiplexer and all platforms will be
equipped with:
Fiber optic patch panel (1 ea.) including fiber optic patch cables
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 14 of 19
D3
Media converter (1 ea.) for fiber to Ethernet conversion
System cabinet (1 ea.) for mounting of media converter and patch panel
Drop/Insert Multiplexers
Fiber Patch Panel:
24 fiber optic patch panel, complete with single mode fiber patch cables
Standard: ISO 11801
19 inch rack mount
COMMUNICATION EQUIPMENT SPECIFICATIONS
Vendor shall supply all telecommunication equipment required to enable a fully operational
telecommunication system. The telecommunication equipment should as far as practical be
supplied complete, having the telecommunication cabinets pre-wired, wit the equipment preinstalled and tested. The Communication equipment specification is further enhanced in the
separate document HN-ETE-SP-GOXX-2901, Telecommunication Equipment Specification.
7.1
Telephones
Three (3) telephone sets shall be provided for each Wellhead platforms WHP-7 and WHP-8 ie,
one in Local Technical Room (LTR) and others in the field (Strategic process area).
Four (4) telephone sets shall be provided for Central Hendijan platform ie, one in Local
Technical Room (LTR) and others in the field (strategic process area).
Various types of telephones shall be provided in different areas on platforms:
Outdoor intrinsically safe telephones shall be provided in strategic locations on
platforms. The outdoor telephones shall be zone 1 certified according the area
classification, complete with acoustic hood.
In plant areas, exposed locations and in high noise areas, where the levels exceed 88
dBA, telephones shall be mounted inside acoustic hoods and provided with external
visual and audible alarms. All visual and audible alarms shall be Zone 1 certified.
Standard digital office type Telephones with all facilities of a modern digital telephone
shall be provided in Technical rooms.
These telephones shall be connected to the existing PABX of Bahregansar platform via fiber
optic and LAN network, providing required interface.
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
7.2
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 15 of 19
D3
Telephone To Ethernet Extender
As it has been decided to send the voice traffic on fibre optic network, each telephone set shall
interface the control system LAN via a telephone to Ethernet extender and also PABX. All of
these interfaces shall have the following specifications:
Extends telephone link via 10 Base-T Ethernet connection
Web-based configuration Interface
PABX & key system (POTS) compatible
Voice bandwidth from 300Hz to 3.4 KHz for Toll Quality Sound
Hardened temperature compatible
Two wire FXS on the telephone side and FXO on the PABX side
The LAN system uses the conventional CAT5 cables, and a self healing multi-drop fiber optic
multiplexer will send the traffic over fiber optic network.
7.3
CCTV Cameras and DVR/CODEC
Three (3) CCTV Cameras shall be provided for each platform ie., one in Top deck, one in Boat
landing level and the third one in Process area.
The outdoor CCTV cameras shall have the following features and the components as a
minimum:
i)
Colour camera modules equipped with night vision capability, 18X optical zoom lenses
and 4X digital zoom installed in EExd enclosure
ii)
Heater and Wiper
iii)
Internal telemetry receiver for camera and wash controls
iv)
Sun-hood / sun-shade
v)
Camera mounting accessories
vi)
Pan/Tilt /Zoom drive units
vii)
Junction Boxes shall be EXe rated and shall be provided to extend the
connectivity of the Camera to DVR/CODEC
viii)
Composite field cables for Power, signals and controls
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
ix)
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 16 of 19
D3
Outdoor mounted equipment such as CCTV cameras and junction boxes shall have
ingress protection of IP 65 as a minimum.
DVR/Codec:
The DVR/Codec shall have the following features or components as minimum:
i)
Manage a minimum of six (6) nos. of field cameras with BNC inputs and convertInto
MPEG-2 minimum, preferably MPEG-4 and ITU-H261/H264 video data streams
formats. Proprietary formats are discouraged.
ii)
Communications and Networking interfaces
iii)
Min. one (1) no. RS 232 and one (1) RS 485 port
iv)
Min. one (1) no. of USB port
v)
Min. one (1) no. of VGA output
vi)
Min. Six (6) no. of BNC 75 ohms for camera inputs
vii)
Simultaneous record, back-up and almost live view
viii)
Search criteria include date, time, camera, event, motion
ix)
Support Video standard PAL
x)
Pan/tilt/Zoom controls capability via RS-485 interface
xi)
Calender and timer function
xii)
Hard disk capacity of 80 GB as minimum, with multi-track recording where required.
xiii) Other features-network /Device Management (optional). Vendor shall propose suitable
management tools for devices/facility management which may include trouble shooting.
The NMS tool shall employ TCP/IP protocol and architecture for seamless integration
to the Ethernet network.
xiv)
Suitable for 19 rack mount.
It has been decided that the video stream data is sent on fiber optic network, the DVR shall be
suitable for interface with the control system LAN via Ethernet extender.
7.4
Self Healing Multi-Drop Multiplexer
As the topology of the optical network is ring, and it is crucial to have always been connected
through this network, a sound modern multiplexer shall be used to send and receive the traffic
intelligently by means of detecting any failure in the network and route the traffic through
another safe link. These MUXs shall be used in each remote wellhead platforms and also
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 17 of 19
D3
Bahregansar central control room. Details regarding drop/insert multiplexers will be developed
by the vendor.
8
COMMUNICATION POWER SUPPLY
All telecom equipment shall be powered by a 230V AC, +/- 10%, 50Hz, Telecom/Control
system UPS. The autonomy of the UPS will be 240 minutes.
All voltage conversion required will be done within each system rack.
The AC UPS system shall be floating and shall be provided with a central earth fault
monitoring system.
9
9.1
SYSTEM INTERFACE REQUIREMENTS
PABX Interface
All users of PABX in Bahregansar Platform shall be enabled to dial an extension number of
each satellite platform, directly with the specified extension.
9.2
Ethernet Interface
In each satellite platform and also in Bahregansar platform there shall be an interface between
fibre optic cable and Ethernet network to facilitate transmission of control and safety
information between these platforms.
10
EQUIPMENT PROTECTION
All equipment located in the Local Technical Room (LTR) shall be suitable for operation in an
air conditioned environment. The ingress protection of communication equipment shall be
selected as described in Instrument Design Basis, equipment located in the Local Technical
Room shall have protection of IP 42.
Equipment installed in process and utilities areas will be zone 1 certified irrespective of area
classification. Wellheads have a zone 2 haven available for locating some equipment.
Equipment will, as a minimum, be certified for gas group IIA & IIB with a temperature class
T3, as minimum.
11
JUNCTION BOX & CABLING
Intrinsically safe circuits shall be segregated from non-I.S. circuits, i.e. non-IS circuits shall not
be introduced into a junction box, multicore cable or termination rails being used for IS
circuits.
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Telecommunication Philosophy
Document Number
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
Page: 18 of 19
D3
Digital and analog signals shall also be segregated into separate junction boxes.
Separate junction boxes will be supplied for Telecommunication circuits Telecommunication
signal shall be adequately separated from power cables and electrical power equipment to
minimise noise interference. A minimum separation distance shall be maintained between
Telecom and power cables in accordance to installation procedures.
12
EARTHING
Field devices will be earthed and the cable armour will be earthed at each cable gland. The
cable screen will be isolated from earth at the field device. The screen shall only be earthed at
one point, which will normally be at the control/ termination panel end of the cable. All unused
cores in intrinsically safe cables shall be connected to IS earth at the termination cabinet. For
typical earthing details, refer HN-EIN-DI-GOXX-2865.
HENDIJAN OFFSHORE COMPLEX
DEVELOPMENT PROJECT
ISOICO
Document Title
Document Number
Telecommunication Philosophy
Area.
Disc.
HN
ETE
Doc. Scope. Seq.
PH
GOXX 2900
Rev.
D3
APPENDIX-01 TYPICAL SCHEMATIC FOR TELECOM
VENDOR'S SCOPE
Page: 19 of 19
H
HE
EN
ND
DIIJJA
AN
NO
OFFFFSSH
HO
OR
RE
EC
CO
OM
MPPL
LE
EX
XD
EN
NT
T
DE
EV
VE
EL
LO
OPPM
ME
PPR
RO
OJJE
EC
CT
T
DESIGN CLARIFICATION /RESPONSE CONTROL SHEET
Doc. No.: HN-ETE-PH-GOXX-2900
Doc.Titel: TELECOMMUNICATION PHILOSOPHY
Rev. Statuse: D2
Response to Transmittal No: letter 87082-219 date:13 Jan 2009
No.
REFERENCE
IOOC COMMENTS
JDD REPLY
COMMENT
STATUS
1-
in section 6.4
Second paragraph shall include multiplexers.
Noted. Included in Rev D3.
2-
In section 7.1,
No IP is specified in tender. For all field devices,
IP65 as already stated in clause 5 of document.
3-
In section 7.1,
Outdoor telephones shall have protection of at least IP
65.
Minimum level of noise shall be reduced to 85 dBA.
As per tender the limitation of acoustic hood is 88
dbA and it is considered in document.
Comments Status
C- Close and implemented
O- Open need to action
N- Noted no action required
Page : 1 of 1
