Worldwide
www.tyco-fire.com
Contacts
Type MV
Directional Spray Nozzles, Open
Medium Velocity
General
Description
The Tyco Type MV Nozzles are open
(non-automatic) directional spray nozzles designed for use in water spray
fixed systems for fire protection applications. They are external deflectortype nozzles that discharge a uniformly filled cone of medium velocity water
droplets.
The MV Nozzles are effective in covering exposed vertical, horizontal,
curved, and irregular shaped surfaces
in a cooling spray to prevent excessive
absorption of heat from an external
fire and possible structural damage or
spread of fire to the protected equipment. In some applications, depending
on water design density requirements,
the Type MV Nozzles may also be used
for fire control or extinguishment.
The Type MV Nozzles are available in a
wide variety of orifice sizes and spray
angles (included angle of discharge) to
provide versatility in system design.
Type MV Nozzles having orifice diameters smaller than 9,5 mm (0.37 in.)
are factory assembled with an orifice
insert and strainer. Strainers have 3,2
mm (1/8 in.) diameter holes. Nozzles
equipped with strainers range in size
from MV10 to MV30 (refer to Table A).
It is recommended that the end user
be consulted with respect to the suitability of the materials of construction
and finish for any given corrosive environment. The effects of ambient temperature, concentration of chemicals,
and gas/chemical velocity, should be
considered, at a minimum, along with
the corrosive nature to which the Type
MV Nozzles may be exposed.
NOTICE
The Tyco Type MV Nozzles described
herein must be installed and maintained in compliance with this document and with the applicable standards of the National Fire Protection
Association, in addition to the standards of any authorities having jurisdiction. Failure to do so may impair the
performance of these devices.
The design of individual water spray
fixed systems can vary considerably,
depending on the characteristics and
nature of the hazard, the basic purpose
of the spraying system, the configuration of the hazard, and wind/draft conditions. Because of these variations, as
well as the wide range of available nozzle spray characteristics, the design of
water spray fixed systems for fire protection must only be performed by experienced designers who thoroughly
understand the limitations as well as
capabilities of such systems.
The owner is responsible for maintaining their fire protection system and devices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Approvals
Refer to Table A
Maximum Working Pressure
12,1 bar (175 psi)
(Refer to Figure 2, Note 2)
Discharge Coefficient
Refer to Table A
Spray Angles
Refer to Table B
Thread Connection
1/2 in. NPT
Physical Characteristics
MV Nozzles are comprised of components constructed from: Stainless
Steel, Brass & Leaded Gunmetal LG2,
Titanium, Aluminum Bronze, SMO254,
or Zeron 100.
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the INSTALLER
WARNING that provides cautions
with respect to handling and installation of sprinkler systems and components. Improper handling and installation can permanently damage
a sprinkler system or its components and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Page 1 of 14
Technical
Data
JULY 2014
TFP807
TFP807
Page 2 of 14
11,1 mm (7/16")
NOMINAL MAKE-IN
1/2" NPT
STRAINER *
WITH NOMINAL
3,2 mm (1/8") DIA.
HOLES
17,5 mm *
(11/16")
WRENCHING
AREA
K-FACTOR
INDICATED ON
FRAME ARM
ORIFICE *
INSERT
65,1 mm
(2-9/16")
ORIFICE SIZE
AND SPRAY ANGLE
(INCLUDED ANGLE
OF DISCHARGE)
INDICATED ON
FRAME ARM
FRAME
55,6 mm
(2-3/16")
SPLITTER
* NOZZLES HAVING
ORIFICES SMALLER
THAN 9,5 mm (0.37")
DIAMETER INCLUDE
ORIFICE INSERT AND
STRAINER
DEFLECTOR
47,6 mm
(1-7/8")
FIGURE 1
TYPE MV NOZZLE ASSEMBLY
AND NOMINAL DIMENSIONS
Orifice
Size
Minimum
Diameter
mm
(Inches)
MV10
5,15 (0.20)
K-factor
Material
LPM/bar1/2
GPM/psi1/2
Stainless
Steel
Brass &
Leaded
Gunmetal
LG2
17,3
1.2
1, 2
1, 2
1, 2
1, 2
Titanium
Aluminum
Bronze
SMO254
Zeron 100
MV12
5,40 (0.21)
18,7
1.3
1, 2
1, 2
1, 2
1, 2
MV15
6,35 (0.25)
25,9
1.8
1, 2
1, 2
1, 2
1, 2
MV18
6,80 (0.27)
28,8
2.0
1, 2
1, 2
1, 2
1, 2
MV19
7,15 (0.28)
31,7
2.2
1, 2
1, 2
1, 2
1, 2
MV21
7,70 (0.30)
36,0
2.5
1, 2
1, 2
1, 2
1, 2
MV25
8,35 (0.33)
41,8
2.9
1, 2
1, 2
1, 2
1, 2
MV26
8,80 (0.34)
44,6
3.1
1, 2
1, 2
1, 2
1, 2
MV30
9,00 (0.35)
49,0
3.4
1, 2
1, 2
1, 2
1, 2
MV34
9,60 (0.38)
59,0
4.1
1, 2
1, 2
1, 2
1, 2
MV47
11,20 (0.44)
79,2
5.5
1, 2
1, 2
1, 2
1, 2
MV57
12,60 (0.50)
100,8
7.0
1, 2
1, 2
1, 2
1, 2
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL)
2. Approved by Factory Mutual Research Corporation (FM)
TABLE A
TYPE MV NOZZLE ORIFICE SIZES, DISCHARGE COEFFICIENTS, MATERIALS OF CONSTRUCTION,
AND LABORATORY LISTINGS AND APPROVALS
90
95
110
125
140
160
TABLE B
TYPE MV NOZZLE SPRAY ANGLES
(INCLUDED ANGLE OF DISCHARGE)
TFP807
Page 3 of 14
AXIAL DISTANCE
NOZZLE
PLANE OF
PROTECTION
SPRAY
PROFILE
RADIAL
DISTANCE
FIXED ANGLE
(ORIENTATION)
NOTES:
GRAVITY
1. Design data obtained from tests in still air.
2. Design data applies to a residual (flowing) pressure range at the nozzle inlet
of 1,4 to 4,1 bar (20 to 60 psi). For pressures up to 12,1 bar (175 psi) consult
Tyco Fire Protection Products Technical Services.
Refer to the authority having jurisdiction for their minimum required residual
pressures.
3. The shapes of the Design Spray Profiles remain essentially unchanged over
the maximum Axial Distances shown in Tables E and F.
4. For axial distances of 0,6 meters (2 feet) and less and for nozzle spray angles
of 90 to 140, the Design SprayFIGURE
Profile is2the same as the nominal spray angle.
WATER
DISTRIBUTION
DESIGN
5. The maximum Axial Distances shown in Tables
E andDATA
F are based on exposure
protection.
Spray Patterns
The Design Spray Profiles for MV nozzle spray angles of 90 to 160 degrees
The Tyco Type MV Nozzles must be inare shown in Graphs A through M and
stalled in accordance with the followapply to discharge pressures of 1,4 to
ing instructions.
Nozzle Placement
4,1 bar (20 to 60 psi). Discharge presWhere direct impingement of water
sures in excess of 4,1 bar (60 psi) will
General Instructions
spray onto all of the protected surresult in a decrease in coverage area
A leak-tight 1/2 in. NPT sprinkler joint
face is required by the authority havsince the spray patterns tend to draw
should be obtained by applying a mining jurisdiction, Type MV Nozzles are
inwards at higher pressures. Refer inimum-to-maximum torque of 9,5 to
to be spaced and directed so that their
quiries on higher discharge pressures
19,0 Nm (7 to 14 ft.-lbs.). Higher levspray patterns will completely cover
to the Technical Services Department.
els of torque can distort the nozzle Inthe plane-of-protection with the miniThe maximum axial distances belet with consequent impairment of the
mum required average density. Howtween the nozzle tip and plane-of-pronozzle.
ever, it is recommended that indoor
tection, for exposure protection, are
Step 1. With pipe-thread sealant apnozzle spacing be 3,7 m (12 ft.) or less
given in Table C and D.
plied to the pipe threads, hand-tighten
and that outdoor nozzle spacing be 3,0
When the axial distance from the nozthe nozzle into the nozzle fitting.
m (10 ft.) or less. Where rundown or
zle tip to the plane-of-protection is 0,6
slippage is planned, for example, exStep 2. With reference to Figure 1,
m (3 ft.) or less, the Design Spray Proposure protection of vessels per NFPA
apply an appropriate size adjustable
file is the same as the nominal spray
15, the above recommended indoor
Crescent wrench to the wrenching
angles
of
90
thru
140
degrees.
and outdoor spacings also apply.
area and tighten the nozzle into the
Design
Criteria
When used for protecting the surfaces
of a vessel, for example, MV nozzles
are positioned normal to and approximately 0,6 m (2 ft.) from the surface.
This approach, in conjunction with
a properly selected spray angle, will
tend to make more effective use of the
spray as well as help minimize the disturbance effects of wind/draft conditions on the water spray patterns.
Installation
Main Pipeline Strainers
Main pipeline strainers per NFPA 15
are required for systems utilizing nozzles with a flow path less than 9,5 mm
(0.37 in.) diameter, that is, MV10 thru
MV30 (Table A), and for any system
where the water is likely to contain obstructive material.
nozzle fitting.
TFP807
Page 4 of 14
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
160
1,0
140
110
95
2,0
4
125
6
90
3,0
10
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH A
TYPE MV10 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
160
1,0
140
110
95
90
2,0
4
125
6
8
3,0
10
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH B
TYPE MV12 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
160
1,0
4
6
2,0
8
3,0
140
110
4,0
125
10
12
90
14
GRAPH C
TYPE MV15 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
TFP807
Page 5 of 14
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
160
1,0
140
4
6
2,0
110
8
3,0
10
90
95
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH D
TYPE MV18 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
160
140
125
1,0
2,0
110
3,0
8
95
90
10
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH E
TYPE MV19 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
2,0
160
140
125
110
4
6
8
3,0
95
90
10
12
4,0
14
GRAPH F
TYPE MV21 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
TFP807
Page 6 of 14
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
160
1,0
2,0
4
140
125
110
3,0
10
90
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH G
TYPE MV25 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
160
140
2,0
125
110
3,0
10
90
12
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH H
TYPE MV26 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
160
2,0
140
125
6
8
3,0
4,0
10
110
12
90
14
GRAPH J
TYPE MV30 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
TFP807
Page 7 of 14
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
160
140
2,0
125
8
3,0
10
110
95
12
90
4,0
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH K
TYPE MV34 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
2,0
160
4
6
140
3,0
4,0
10
125
110
90
12
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
14
GRAPH L
TYPE MV47 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
6
8
10 12
4
2
0
2
1,0
2,0
160
4
6
140
8
3,0
125
10
110
4,0
90
12
95
14
GRAPH M
TYPE MV57 DESIGN SPRAY PROFILES
0 FIXED ANGLE, 4,1 BAR (60 PSI)
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, FEET
AXIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
RADIAL DISTANCE FROM
NOZZLE CENTERLINE, METERS
4,0
3,0
2,0
1,0
0
0
TFP807
Page 8 of 14
MAXIMUM AXIAL DISTANCE FOR 90 SPRAY ANGLE IN METERS
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
2,4
2,1
3,8
3,7
3,0
3,5
3,4
3,5
3,9
3,8
3,9
4,1
45
1,9
1,6
1,7
2,0
1,8
2,1
2,1
2,1
2,4
1,9
2,1
2,5
90
1,0
1,1
1,3
1,5
1,7
1,7
1,5
1,4
1,7
1,7
1,8
2,3
135
0,8
0,8
0,8
0,8
0,8
0,9
1,2
1,3
1,1
1,1
1,2
1,6
180
0,5
0,5
0,5
0,8
0,8
0,8
0,8
0,8
1,0
0,9
1,1
1,4
MAXIMUM AXIAL DISTANCE FOR 95 SPRAY ANGLE IN METERS
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
1,9
1,9
3,6
3,5
2,9
3,0
2,7
2,7
3,5
3,7
3,7
3,8
45
1,5
1,5
1,5
1,9
1,7
1,8
1,8
2,1
2,0
1,8
2,0
2,2
90
0,9
1,0
1,2
1,4
1,5
1,2
1,4
1,4
1,6
1,6
1,7
2,1
135
0,8
0,7
0,7
0,8
0,8
0,8
0,9
1,0
0,9
1,1
1,1
1,4
180
0,5
0,5
0,5
0,6
0,7
0,5
0,7
0,7
0,8
0,8
1,0
1,2
MAXIMUM AXIAL DISTANCE FOR 110 SPRAY ANGLE IN METERS
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
1,8
1,8
45
1,1
1,4
3,4
2,1
2,4
2,0
2,4
2,3
3,2
3,0
3,7
3,7
1,4
1,5
1,8
1,6
1,7
2,0
1,6
1,7
1,8
2,1
90
0,8
0,9
1,1
1,2
1,2
1,2
1,3
1,3
1,5
1,5
1,6
1,8
135
0,5
0,6
0,6
0,7
0,6
0,7
0,8
0,7
0,8
0,9
0,9
1,0
180
0,4
0,3
0,4
0,5
0,5
0,5
0,6
0,6
0,7
0,8
0,8
0,8
TABLE C, PART 1 OF 2
MAXIMUM AXIAL DISTANCE BETWEEN NOZZLE TIP
AND PLANE-OF-PROTECTION FOR EXPOSURE PROTECTION
(METRIC)
TFP807
Page 9 of 14
MAXIMUM AXIAL DISTANCE FOR 125 SPRAY ANGLE IN METERS
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
1,7
1,5
3,0
1,7
1,6
1,7
1,9
2,1
2,1
2,1
3,4
2,9
45
1,1
1,3
1,4
1,2
1,4
1,4
1,4
1,4
1,3
1,5
1,3
1,8
90
0,6
0,7
0,9
1,0
1,1
1,1
1,1
1,2
1,2
1,4
1,2
1,4
135
0,5
0,5
0,5
0,5
0,5
0,5
0,6
0,6
0,7
0,8
0,8
0,8
180
0,3
0,2
0,3
0,4
0,4
0,4
0,5
0,4
0,5
0,6
0,7
0,6
MAXIMUM AXIAL DISTANCE FOR 140 SPRAY ANGLE IN METERS
Fixed
Angle
0
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
1,1
1,4
2,7
1,2
1,3
1,4
1,7
1,5
1,8
1,7
2,2
1,9
45
0,8
1,0
1,3
0,9
1,1
1,1
1,3
1,1
1,2
1,3
1,2
1,7
90
0,5
0,5
0,8
0,8
0,9
1,0
1,0
1,0
1,0
1,1
1,1
1,2
135
0,4
0,4
0,4
0,4
0,4
0,4
0,5
0,5
0,5
0,8
0,6
0,7
180
0,2
0,2
0,2
0,3
0,2
0,3
0,4
0,3
0,4
0,5
0,6
0,5
MAXIMUM AXIAL DISTANCE FOR 160 SPRAY ANGLE IN METERS
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
0,5
1,0
0,9
0,8
0,7
0,9
0,9
1,0
1,1
1,1
1,2
1,4
45
0,5
0,5
0,7
0,8
0,5
0,6
0,8
0,9
1,1
1,1
1,1
1,1
90
0,2
0,4
0,4
0,7
0,7
0,7
0,7
0,8
0,8
0,8
0,8
1,1
135
0,2
0,3
0,2
0,2
0,3
0,2
0,2
0,2
0,3
0,5
0,5
0,5
180
0,2
0,1
0,2
0,2
0,2
0,2
0,2
0,2
0,2
0,4
0,5
0,4
TABLE C, PART 2 OF 2
MAXIMUM AXIAL DISTANCE BETWEEN NOZZLE TIP
AND PLANE-OF-PROTECTION FOR EXPOSURE PROTECTION
(METRIC)
TFP807
Page 10 of 14
MAXIMUM AXIAL DISTANCE FOR 90 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
7-9
7-0
12-6
12-0
10-0
11-6
11-0
11-6
12-9
12-6
12-9
13-6
45
6-3
5-3
5-6
6-6
5-9
6-9
7-0
7-0
7-9
6-3
7-0
8-3
90
3-3
3-6
4-3
5-0
5-6
5-6
5-0
4-9
5-6
5-6
6-0
7-6
135
2-9
2-6
2-6
2-9
2-9
3-0
4-0
4-3
3-6
3-9
4-0
5-3
180
1-9
1-9
1-9
2-6
2-9
2-9
2-6
2-9
3-3
3-0
3-9
4-6
MAXIMUM AXIAL DISTANCE FOR 95 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
6-3
6-3
11-9
11-6
9-6
10-0
9-0
9-0
11-6
12-0
12-3
12-6
45
5-0
5-0
5-0
6-3
5-6
6-0
6-0
6-9
6-6
6-0
6-6
7-3
90
3-0
3-3
4-0
4-6
5-0
4-0
4-6
4-6
5-3
5-3
5-6
6-9
135
2-6
2-3
2-3
2-6
2-6
2-6
3-0
3-3
3-0
3-6
3-6
4-9
180
1-6
1-6
1-6
2-0
2-3
1-9
2-3
2-3
2-6
2-9
3-3
4-0
MAXIMUM AXIAL DISTANCE FOR 110 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
6-0
6-0
11-0
7-0
8-0
6-6
8-0
7-6
10-6
10-0
12-0
12-0
45
3-9
4-6
4-9
5-0
5-9
5-3
5-6
6-6
5-3
5-6
6-0
7-0
90
2-9
3-0
3-9
4-0
4-0
4-0
4-3
4-3
5-0
5-0
5-3
5-9
135
1-9
2-0
2-0
2-3
2-0
2-3
2-6
2-3
2-6
3-0
3-0
3-3
180
1-3
1-0
1-3
1-6
1-9
1-6
2-0
2-0
2-3
2-6
2-9
2-9
TABLE D, PART 1 OF 2
MAXIMUM AXIAL DISTANCE BETWEEN NOZZLE TIP
AND PLANE-OF-PROTECTION FOR EXPOSURE PROTECTION
(IMPERIAL)
TFP807
Page 11 of 14
MAXIMUM AXIAL DISTANCE FOR 125 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
9-6
5-6
5-0
10-0
5-6
5-3
5-6
6-3
6-9
7-0
6-9
11-0
45
3-6
4-3
4-6
4-0
4-6
4-6
4-9
4-6
4-3
5-0
4-3
5-9
90
2-0
2-3
3-0
3-3
3-6
3-6
3-9
4-0
4-0
4-9
4-0
4-6
135
1-6
1-6
1-6
1-9
1-6
1-6
2-0
2-0
2-3
2-9
2-9
2-6
180
1-0
0-9
1-0
1-3
1-3
1-3
1-6
1-3
1-9
2-0
2-3
2-0
MAXIMUM AXIAL DISTANCE FOR 140 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
MV47
MV57
3-6
4-9
9-0
4-0
4-3
4-9
5-6
5-0
6-0
5-6
7-3
6-3
45
2-9
3-3
4-3
3-0
3-9
3-9
4-3
3-6
4-0
4-3
4-0
5-6
90
1-6
1-9
2-6
2-6
3-0
3-3
3-3
3-3
3-3
3-6
3-9
4-0
135
1-3
1-3
1-3
1-3
1-3
1-3
1-6
1-9
1-6
2-6
2-0
2-3
180
0-9
0-6
0-9
1-0
0-9
1-0
1-3
1-0
1-3
1-6
2-0
1-9
MV47
MV57
MAXIMUM AXIAL DISTANCE FOR 160 SPRAY ANGLE IN FEET AND INCHES
Fixed
Angle
Orifice Size
MV10
MV12
MV15
MV18
MV19
MV21
MV25
MV26
MV30
MV34
1-6
3-3
3-0
2-6
2-3
3-0
45
1-6
1-6
2-3
2-6
1-9
2-0
3-0
3-3
3-6
3-6
4-0
4-6
2-9
3-0
3-6
3-9
3-6
3-9
90
0-9
1-3
1-3
2-3
2-3
2-3
2-3
2-6
2-6
2-6
2-9
3-6
135
0-6
1-0
0-9
0-9
1-0
0-9
0-9
0-9
1-0
1-6
1-6
1-6
180
0-6
0-3
0-6
0-9
0-6
0-6
0-6
0-6
0-6
1-3
1-6
1-3
TABLE D, PART 2 OF 2
MAXIMUM AXIAL DISTANCE BETWEEN NOZZLE TIP
AND PLANE-OF-PROTECTION FOR EXPOSURE PROTECTION
(IMPERIAL)
TFP807
Page 12 of 14
Stainless Steel
Spray Angle
Orifice
Size
90
95
110
125
140
160
MV10
AED07603
AED00024
AED00033
AED00042
AED00051
AED02560
MV12
AED07612
AED07621
AED07630
AED07649
AED07658
AED07667
MV15
AED07676
AED00088
AED00097
AED00109
AED00118
AED00127
MV18
AED07685
AED07694
AED07706
AED07715
AED07724
AED07733
MV19
AED07742
AED00145
AED00154
AED00163
AED00172
AED00181
MV21
AED07760
AED07779
AED07788
AED07797
AED07809
AED07818
MV25
AED07751
AEA00202
AEA00211
AED00220
AEA00239
AEA00248
MV26
AED07827
AED07836
AED07845
AED07854
AED07863
AED07872
MV30
AED07881
AED07890
AED07902
AED07911
AED07920
AED07939
MV34
AED07948
AED01218
AED01227
AED01236
AED01245
AED01254
MV47
AED07957
AED01272
AED01281
AED01290
AED01302
AED01311
MV57
AED07966
AED01339
AED01348
AED01357
AED01366
AED01375
Brass & Leaded Gunmetal LG2
Spray Angle
Orifice
Size
90
95
110
125
140
160
MV10
AED03829
AED02524
AED02533
AED02542
AED02551
AED02560
AED03883
MV12
AED03838
AED03847
AED03856
AED03865
AED03874
MV15
AED03892
AED02588
AED02597
AED02609
AED02618
AED02627
MV18
AED03904
AED03913
AED03922
AED03931
AED03940
AED03959
MV19
AED03968
AED02645
AED02654
AEA02663
AED02672
AED02681
MV21
AED03977
AED03986
AED03995
AED04004
AED04013
AED04022
MV25
AED04031
AEA02702
AEA02711
AEA02720
AEA02739
AEA02748
MV26
AED04040
AED04059
AED04068
AED04077
AED04086
AED04095
MV30
AED04107
AED04116
AED04125
AED04134
AED04143
AED04152
MV34
AED04161
AED00949
AED00958
AED00967
AED00976
AED00985
MV47
AED04170
AED01003
AED01012
AED01021
AED01030
AED01049
MV57
AED04189
AED01067
AED01076
AED01085
AED01094
AED01106
140
160
Titanium
Spray Angle
Orifice
Size
90
95
110
125
MV10
AED07603T
AED00024T
AED00033T
AED00042T
AED00051T
AED02560T
MV12
AED07612T
AED07621T
AED07630T
AED07649T
AED07658T
AED07667T
MV15
AED07676T
AED00088T
AED00097T
AED00109T
AED00118T
AED00127T
MV18
AED07685T
AED07694T
AED07706T
AED07715T
AED07724T
AED07733T
MV19
AED07742T
AED00145T
AED00154T
AED00163T
AED00172T
AED00181T
MV21
AED07760T
AED07779T
AED07788T
AED07797T
AED07809T
AED07818T
MV25
AED07751T
AEA00202T
AEA00211T
AED00220T
AEA00239T
AEA00248T
MV26
AED07827T
AED07836T
AED07845T
AED07854T
AED07863T
AED07872T
MV30
AED07881T
AED07890T
AED07902T
AED07911T
AED07920T
AED07939T
MV34
AED07948T
AED01218T
AED01227T
AED01236T
AED01245T
AED01254T
MV47
AED07957T
AED01272T
AED01281T
AED01290T
AED01302T
AED01311T
MV57
AED07966T
AED01339T
AED01348T
AED01357T
AED01366T
AED01375T
TABLE E PART 1 OF 2
TYPE MV NOZZLE
PART NUMBERS
TFP807
Page 13 of 14
Aluminum Bronze
Spray Angle
Orifice
Size
90
95
110
125
140
160
MV10
AED03829AB
AED02524AB
AED02533AB
AED02542AB
AED02551AB
AED02560AB
MV12
AED03838AB
AED03847AB
AED03856AB
AED03865AB
AED03874AB
AED03883AB
MV15
AED03892AB
AED02588AB
AED02597AB
AED02609AB
AED02618AB
AED02627AB
MV18
AED03904AB
AED03913AB
AED03922AB
AED03931AB
AED03940AB
AED03959AB
MV19
AED03968AB
AED02645AB
AED02654AB
AED02663AB
AED02672AB
AED02681AB
AED04022AB
MV21
AED03977AB
AED03986AB
AED03995AB
AED04004AB
AED04013AB
MV25
AED04031AB
AEA02702AB
AEA02711AB
AEA02720AB
AEA02739AB
AEA02748AB
MV26
AED04040AB
AED04059AB
AED04068AB
AED04077AB
AED04086AB
AED04095AB
MV30
AED04107AB
AED04116AB
AED04125AB
AED04134AB
AED04143AB
AED04152AB
MV34
AED04161AB
AED00949AB
AED00958AB
AED00967AB
AED00976AB
AED00985AB
MV47
AED04170AB
AED01003AB
AED01012AB
AED01021AB
AED01030AB
AED01049AB
MV57
AED04189AB
AED01067AB
AED01076AB
AED01085AB
AED01094AB
AED01106AB
SMO254
Spray Angle
Orifice
Size
90
95
110
125
140
160
MV10
AED07603SMO
AED00024SMO
AED00033SMO
AED00042SMO
AED00051SMO
AED02560SMO
AED07667SMO
MV12
AED07612SMO
AED07621SMO
AED07630SMO
AED07649SMO
AED07658SMO
MV15
AED07676SMO
AED00088SMO
AED00097SMO
AED00109SMO
AED00118SMO
AED00127SMO
MV18
AED07685SMO
AED07694SMO
AED07706SMO
AED07715SMO
AED07724SMO
AED07733SMO
MV19
AED07742SMO
AED00145SMO
AED00154SMO
AED00163SMO
AED00172SMO
AED00181SMO
MV21
AED07760SMO
AED07779SMO
AED07788SMO
AED07797SMO
AED07809SMO
AED07818SMO
MV25
AED07751SMO
AEA00202SMO
AEA00211SMO
AED00220SMO
AEA00239SMO
AEA00248SMO
MV26
AED07827SMO
AED07836SMO
AED07845SMO
AED07854SMO
AED07863SMO
AED07872SMO
MV30
AED07881SMO
AED07890SMO
AED07902SMO
AED07911SMO
AED07920SMO
AED07939SMO
MV34
AED07948SMO
AED01218SMO
AED01227SMO
AED01236SMO
AED01245SMO
AED01254SMO
MV47
AED07957SMO
AED01272SMO
AED01281SMO
AED01290SMO
AED01302SMO
AED01311SMO
MV57
AED07966SMO
AED01339SMO
AED01348SMO
AED01357SMO
AED01366SMO
AED01375SMO
140
160
Zeron 100
Spray Angle
Orifice
Size
90
95
110
125
MV10
AED07603Z
AED00024Z
AED00033Z
AED00042Z
AED00051Z
AED02560Z
MV12
AED07612Z
AED07621Z
AED07630Z
AED07649Z
AED07658Z
AED07667Z
MV15
AED07676Z
AED00088Z
AED00097Z
AED00109Z
AED00118Z
AED00127Z
MV18
AED07685Z
AED07694Z
AED07706Z
AED07715Z
AED07724Z
AED07733Z
MV19
AED07742Z
AED00145Z
AED00154Z
AED00163Z
AED00172Z
AED00181Z
MV21
AED07760Z
AED07779Z
AED07788Z
AED07797Z
AED07809Z
AED07818Z
MV25
AED07751Z
AEA00202Z
AEA00211Z
AED00220Z
AEA00239Z
AEA00248Z
MV26
AED07827Z
AED07836Z
AED07845Z
AED07854Z
AED07863Z
AED07872Z
MV30
AED07881Z
AED07890Z
AED07902Z
AED07911Z
AED07920Z
AED07939Z
MV34
AED07948Z
AED01218Z
AED01227Z
AED01236Z
AED01245Z
AED01254Z
MV47
AED07957Z
AED01272Z
AED01281Z
AED01290Z
AED01302Z
AED01311Z
MV57
AED07966Z
AED01339Z
AED01348Z
AED01357Z
AED01366Z
AED01375Z
TABLE E PART 2 OF 2
TYPE MV NOZZLE
PART NUMBERS
TFP807
Page 14 of 14
Care and
Maintenance
The TYCO Type MV Nozzles must
be maintained and serviced in
accordance
with
the
following
instructions.
NOTICE
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, obtain permission to shut
down the affected fire protection system from the proper authorities and
notify all personnel who may be affected by this action.
Type MV Nozzles must never be painted, plated, coated or altered in any
way after leaving the factory; otherwise, the spray performance may be
impaired.
Exercise care to avoid damage to the
nozzles, before, during, and after installation. Replace nozzles damaged
by dropping, striking, wrench twist/
slippage, or the like.
Frequent visual inspections are recommended to be initially performed
for nozzles installed in potentially corrosive atmospheres to verify the integrity of the materials of construction
and finish as they may be affected by
the corrosive conditions present for a
given installation. Thereafter, annual
inspections per NFPA 25 are required.
Water spray fixed systems to fire
protection service require regularly
scheduled care and maintenance by
trained personnel.
In addition to inspecting nozzles for
proper spray performance during water flow trip tests of the system, it is
recommended that nozzles be periodically inspected for broken or missing parts, loading/obstructions, or other evidence of impaired protection.
The inspections should be scheduled
weekly or as frequently as may be
necessary, and corrective action must
be taken to ensure that the nozzles will
perform as intended in the event of a
fire.
The owner is responsible for the inspection, testing, and maintenance of
their fire protection system and devices in compliance with this document, as well as with the applicable
standards of the National Fire Protection Association (for example, NFPA
25), in addition to the standards of any
authorities having jurisdiction. The installing contractor or sprinkler manufacturer should be contacted relative
to any questions.
Limited
Warranty
For warranty terms and conditions,
visit www.tyco-fire.com.
Ordering
Procedure
When placing an order, indicate the
full product name and part number
(P/N). Contact your local distributor for
availability.
Type MV Nozzles
Specify: Type MV Directional Spray
Nozzle, Open, Medium Velocity, orifice
size (specify), material (specify), spray
angle (specify degrees), P/N (specify
from Table E).
Water spray fixed systems are recommended to be inspected, tested, and
maintained by a qualified Inspection
Service in accordance with local requirements and/or national codes.
GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700
Copyright 2014 Tyco Fire Products, LP. All rights reserved.
