Desmopan 453 DPS 041

400 grade series, ester / Shore hardness D 50 - 54

injection molding grade; grease and oil-resistant; hydrolysis-stabilised; low compression set; good
wear resistance; Application; Injection molded engineering parts; Automotive engineering; Coupling
elements

ISO Shortname
Property

Test Condition

Unit

Standard

typical
Value
drying

annealed

according to specifications

Mechanical properties (23 C/50 % r. h.)

ISO 868

C shore hardness, method D

ISO 868

97
51

Ultimate tensile strength

200 mm/min

MPa

DIN 53504

37,9

Strain at break

200 mm/min

DIN 53504

472

Stress at 10 % strain

200 mm/min

MPa

DIN 53504

8,2

Stress at 50 % strain

200 mm/min

MPa

DIN 53504

15,1

Stress at 100 % strain

200 mm/min

MPa

DIN 53504

18,3

Stress at 300 % strain

200 mm/min

MPa

DIN 53504

30,6

C Compression set

24 h; 70 C

ISO 815

27

C Compression set

72 h; 23 C

ISO 815

15

mm

ISO 4649 method A

32

ISO 4662

30

500 mm/min

kN/m

ISO 34-1

180

Tensile storage modulus

-20 C

MPa

ISO 6721-1,-4

1780

Tensile storage modulus

20 C

MPa

ISO 6721-1,-4

240

Tensile storage modulus

60 C

MPa

ISO 6721-1,-4

110

kg/m

ISO 1183-1

Injection molding-Melt temperature

Injection molding-Mold temperature

20 - 40

Maximum drying temperature

110

C Abrasion resistance
Impact resilience
Tear propagation resistance
Thermal properties

Other properties (23 C)

1230

Molding conditions
220 - 240

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for
plastics according to ISO 10350.
Impact properties: N = non-break, P = partial break, C = complete break

Page 1 of 2 pages

Edition 23.01.2015

ISO Datasheet

Desmopan 453 DPS 041

Disclaimer
Desmopan Disclaimer for Sales products
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties
are involved. Our advice does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and
processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in
accordance with the current version of our General Conditions of Sale and Delivery.
Desmopan Typical value
The shown values are typical values only. Unless explicitly agreed in written form, they do not constitute a binding material specification or warranted values. Values may be affected by the design of
the mold/die, the processing conditions and coloring/pigmentation of the product. Unless specified to the contrary, the property values given have been established on standardized test specimens at
room temperature.
Desmopan Processing note
Under the recommended processing conditions small quantities of decomposition product may be given off during processing. To preclude any risk to the health and well-being of the machine
operatives, tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at the workplace in accordance with the Safety Data Sheet. In
order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products, the prescribed processing temperatures should not be substantially exceeded.
Desmopan No Medical-, Food Contact- and Cosmetic Applications
This product is not designated as "Medical Grade"[i] and therefore shall not be considered a candidate for the manufacture of a medical device or of intermediate products for medical devices, which
are intended under normal use to be brought into direct contact with the patient's body (e.g., skin, body fluids or tissues, including indirect contact to blood)*. This product is also not designated for
Food Contact[ii], including drinking water, or Cosmetic Applications. If the intended use of the product is for the manufacture of a medical device or of intermediate products for medical devices,
for Food Contact products or Cosmetic Applications, Bayer MaterialScience Aktiengesellschaft (BMS-PUR-CO-TPU EMEA/LA) must be contacted in advance to provide its agreement to sell such
product for such purpose. Nonetheless, any determination as to whether a product is appropriate for use in a medical device or intermediate products for medical devices, for Food Contact products
or Cosmetic Applications must be made solely by the purchaser of the product without relying upon any representations by Bayer MaterialScience Aktiengesellschaft (BMS-PUR-CO-TPU EMEA/LA).
[i] Please see the "Guidance on Use of Bayer MaterialScience Products in a Medical Application" document. [ii] As defined in Commission Regulation VO (EU) 1935/2004.
Desmopan General disclaimer
The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written or by way of production evaluations), including
any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products, technical assistance and information to determine to your own
satisfaction whether our products, technical assistance and information are suitable for your intended uses and applications. This application-specific analysis must at least include testing to
determine suitability from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us. Unless we otherwise agree in writing, all products
are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request. All information and technical assistance is given without warranty or guarantee and is
subject to change without notice. It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in connection with
the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a
recommendation to use any product in conflict with any claim of any patent relative to any material or its use. No license is implied or in fact granted under the claims of any patent.

Bayer MaterialScience AG
Business Unit Polyurethanes
51368 Leverkusen
Germany
www.TPU.bayer.com
www.bayermaterialscience.com

Page 2 of 2 pages

Edition 23.01.2015

ISO Datasheet