Industrial cabling technology

for Industrial Ethernet/PROFINET and PROFIBUS

Brochure November 2008

SIMATIC NET
Introduction

Introduction
networks the backbone of industrial communication

PROFINET

Control
(e.g. SIMATIC S7-300)

Motion Control
(e.g. SIMOTION)

Intelligent field devices

(e.g. ET 200S/CPU)

According to the standards ISO/IEC 11801 and EN 50173

for structured building cabling, corresponding standards
were created:

Simple field devices

(e.g. ET 200)

ISO/IEC 24702 for structured cabling of

industrial buildings
IEC 61918 for specific cabling in industrial plants

Sensors/actuators

Enterprise Resource
Planning (ERP)
(e.g. PC)

Drives
(e.g. SINAMICS)

SIRIUS
motor starters

SINUMERIK

Safety-oriented
communication

not suitable

PROFIBUS
DP

Use of the communication systems

Industrial
Ethernet

Powerful, open and rugged bus systems that ensure

efficient communication in automation solutions,
regardless of whether they are intended for data
communication, or for process or field communication:
Networks must be the reliable medium of data transmission in industrial communication.
Openness and flexibility of the individual bus systems
in different topologies enable systems and their expansions to be linked. By using standardized bus systems,
it is possible to connect standardized components from
different suppliers without any problems. This provides
maximum protection of investment, as existing networks can be extended without any adverse effects.
Siemens provides all of the components for an integrated overall solution beyond the network's limits.
This not only includes active network components but
also industry-standard connection systems.

Introduction

suitable

ideally suitable

Components for the network

Both passive network components (e.g. cables, connectors, bus terminals) and active network components
(e.g. switches) are used in constructing an electrical or
optical network. Network cabling in the industrial sector is a significantly greater challenge than in the office
world.
Cables for data and energy
Data lines
Unlike cables in the office, industrial cables must be able
to withstand an aggressive environment and high temperatures or have excellent resistance to lateral force. This is
achieved by means of the special cable construction (star
quad). The cables are silicon-free, which also makes them
suitable for use in paintshops. Thanks to the low bending
radius they withstand the high tensile loads that occur particularly when the cables are pulled into cable ducts.
The capacity to bear mechanical and chemical loads is an
important criterion for industrial cables.
The shielded cable construction permits secure data transmission even in industrial areas subject to electromagnetic
interference.
Power lines
Various rugged power cables are available for the construction of PROFINET/PROFIBUS networks. They are also
silicon-free and can therefore also be used in paintshops.
The cable jacket is resistant to mineral oil and grease and
protects the power line in harsh industrial environments.

Contents

Introduction

Networks The backbone of industrial

communication ..................................................
Components for the network ..............................
Passive and active components in the network .....
A fault-free connection on-site in 60 seconds
with FastConnect ..............................................
FastConnect for Industrial Ethernet ....................
FastConnect for PROFIBUS ...................................

6
7
8

Industrial Ethernet

2
3
4

Network selection criteria .................................... 9

Electrical Industrial Ethernet network ................. 10
Overview of electrical Industrial Ethernet cables . 11
Plug-in connector for Industrial Ethernet ............. 12
Patch technology for Industrial Ethernet ............. 14
Electrical Industrial Ethernet network
Which connector fits which cable? ..................... 16
Optical Industrial Ethernet network
Overview of optical cables ................................. 17
Optical Industrial Ethernet network
Which connector fits which cable? ..................... 20
PROFIBUS

21

Network selection criteria ..................................

Electrical PROFIBUS network ..............................
Electrical PROFIBUS network
Overview of PROFIBUS bus cables ......................
Optical PROFIBUS network
Overview of optical cables .................................
Optical PROFIBUS network
Overview of optical PROFIBUS bus cables ............
Connection components for PROFIBUS ...............
Electrical and optical PROFIBUS network
Which connector fits which cable? .....................

21
23
24
26
28
29
30

Introduction

Passive and active components in the network

The active network components connect individual network segments to form a network structure. On removal or
failure of a network component, the topology is forced to
divide into separate partial segments. As a consequence,
communication between the nodes in the two different
sub-networks is no longer possible.

Communication or sub-network failures can be prevented

by configuring ring or star topologies. These structures can
be implemented with the aid of the SCALANCE X family of
products.

Switching cabinet
FC FO
Standard
Cable GP

Switching cabinet

SIMATIC
TP277B
SIMATIC S7-300
with CP 343-1

IE TP Cord

Switch
SCALANCE
X204-2

IE FC RJ45
Modular
Outlet

,()&6WDQGDUG&DEOH

,(&RQQHFWLQJ&DEOH0
(7SUR
ZLWK&0,0
310

Industrial Ethernet/PROFINET connection options for any application (ring and star topology)

Ring topology

Star topology

The ring topology is created by connecting the two ends

of the lines of an active linear topology into a physical ring.
A special redundancy mechanism ensures that the ring
structure remains a logical line in normal circumstances
and therefore prevents any message frames from circulating. On failure of a ring section or by means of active
network components, the mechanism ensures that an
alternative route is quickly available in the ring. The network does not break up into two segments. The effects of
a network component fault are therefore confined to the
failed component and any terminal equipment connected
to it. If a ring section is interrupted, e.g. due to a broken
cable, communication continues to function without any
disturbance. The reconfiguration time in this case is less
than in the office environment and thus meets the
demands of the automation world.

The star topology uses a central hub (switch). The individual nodes in the network are connected to the active
network components via individual point-to-point connections.
The tree structure is created by the hierarchical arrangement in series of several star structures to form a single
network.

Introduction

In practice, depending on the requirements for the individual transmission routes, it may be a matter of combining
fiber-optic cables and twisted-pair cables. Typical application examples include the Ethernet office networking or
the networking of production cells in a production plant
using Industrial Ethernet. In comparison with the ring or
linear structure, the amount of cabling is considerably
greater due to the long paths back to the star point.

Switching cabinet
6&$/$1&(;
IE TP Cord 2x2

IE FC RJ45
Modular
Outlet
Insert 1GE

IE FC RJ45
Modular
Outlet
Insert 2FE

IE FC RJ45
Modular
Outlet
Insert 2FE

S7-300

ET 200S

IE TP Cord 4x2

PC

,()&6WDQGDUG&DEOH[
[0ELWVFRQQHFWLRQ

IE FC RJ45
Modular
Outlet
Insert 1GE

Connection for Fast and Gigabit Ethernet (linear topology)

Linear topology
In a linear network topology, the network component
typically only has one or just a few connection points for
network stations.
Furthermore, linear structures can also be constructed
using devices with two integrated network interfaces.

Introduction

A fault-free connection on-site in 60 seconds

with FastConnect

Problems often occur on-site when laying the cabling for

industrial plants: When stripping the cable, assembling the
plug-in connector, or if cables are connected incorrectly.

With optimally matched components, SIMATIC NET

cables enable the installation of high-performance industrial network structures.

If you want:
perfectly matched components
the installation of industry-standard network structures
within the shortest possible time without specialist
knowledge
minimal time spent connecting terminals
to avoid installation errors
even easy assembly on-site
and the resulting reduced overall costs during the
lifespan of the system
then the quick-assembly system
FastConnect from SIMATIC NET is the right system for you.
It consists of a cable, connector and tool and can be used
for Industrial Ethernet/PROFINET and PROFIBUS.

Minimal installation time

Easy stripping of outer sheath and braided shield in one
step
Simple connection method for Industrial Ethernet
FastConnect cables
Easy assembly thanks to preset FastConnect stripping
tool
Reliable shield contacting and strain relief
M12 and RJ45 connection method for Industrial Ethernet/PROFINET and PROFIBUS

The advantages add up with FastConnect

With the FastConnect (FC) system for Industrial
Ethernet, structured cabling from the office environment becomes industry-standard for installation in
production halls:
7

7
7
7

An integrated system of FC plug-in connectors and

an extensive range of FC cables with appropriate
UL approvals for Industrial Ethernet/PROFINET and
PROFIBUS
Error avoidance through the use of color coding,
preset tools, and clearly specified materials
Dependable screen contacts and strain relief as
well as good EMC shielding for copper cabling
The use of standard-compliant connection
technology for Industrial Ethernet/PROFINET
and PROFIBUS

Introduction

FastConnect for Industrial Ethernet

Industrial Ethernet/
PROFINET
Fast connection of:
RJ45 plug-in connectors
2 x 2 and 4 x 2
applying the insulation
displacement method
using a stripping tool
to stripped 4 and 8-core
IE FC bus cables
M12 plug-in connectors
by means of stripping
tool to stripped 4-core
IE FC bus cables

Stripping

Assembly with RJ45 plug-in connector

Assembly with M12 plug-in connector

Introduction

FastConnect for PROFIBUS

PROFIBUS
Fast connection of:
Bus connector
by means of insulation
displacement method
using stripping tool
to bared PB FC bus cables
M12 plug
using stripping tool
to bared PB FC bus cables

PROFIBUS PA
(hazardous area)
Fast setup of:
Fieldbus segments
According to IEC 61158-2;
terminals can be connected with FC process cable
or SpliTConnect M12 outlet/M12 jack

Stripping and assembly by means of insulation displacement

Stripping and assembly with M12 plug-in connector

SpliTConnect

Introduction

Industrial Ethernet
network selection criteria
The type of network (electrical or optical, copper or
fiber-optic cables) is determined by the environmental conditions in which it is
to be constructed.

Twisted pair network

Fiber-optic network

Flexibility of the network

topology

n n n n

n n n n

Suitability for high transmission

rates

n n n ,

Inter-building networking

, , , ,

n n n n

EMC

n n n ,

n n n n

Simple cable laying

n n n ,

n n n ,

Range of cables for special

applications

Cables for indoors;

trailing cables; ship wiring cables;
FastConnect cables

Cables for indoors and

outdoors; trailing cables;
halogen-free cables

Effect of voltage failure

Failure of a subnetwork 2)

Failure of a subnetwork 2)

Effect of path failure

Network splits into two separately

functioning subnetworks 3)

Network splits into two separately

functioning subnetworks 3)

Max. network expansion

5000 m

Max. distance between two

network nodes/access points

100 m

50 m POF
100 m PCF
3000 m multi-mode
70000 m single mode

Max. length of connecting cable

100 m

50 m POF
100 m PCF
3000 m multi-mode
70000 m single mode

Pre-assembled cables

Yes

Yes

Assembly on site

without special tool;

FastConnect technology

with special tool

Integrated diagnostics support

LED indicators; signaling contact;

SNMP network management;
Web-based management,
PROFINET diagnostics

LED indicators; signaling contact;

SNMP network management;
Web-based management,
PROFINET diagnostics

Redundant network structures

Electrical ring or doubling of the

infrastructure (linear, star, tree)

Optical ring or doubling of the infrastructure (linear, star, tree)

1) Suitable for 10 Mbit/s, 100 Mbit/s and

1000 Mbit/s
2) Safeguard against subnetwork failure
by means of redundant power supply
3) No effect with ring structure
4) With 50 switches in the ring

n
n
n
n
,

1)

4)

n n n n

1)

Up to 150 km:
over 150 km, consider signal
propagation delay

n
n
n
,
,

n
n
,
,
,

n
,
,
,
,

suitable
partially suitable
not applicable

Introduction

Electrical Industrial Ethernet network

Installation cables

Standard cable for universal applications

Trailing cable for moving machine parts
Cable approved for laying in ships and offshore units
Flexible cable for occasional movement
Torsion-resistant cable for robotic applications
(TP torsion cable)

IE FC stripping tool
The Industrial Ethernet FC stripping tool saves time when
stripping the FC cables.
Due to the accurately preset cutting depths and spacing of
the blades it is possible to remove the outer sheath and the
braided shield of the FC cables to the precise measurement
in a single operation. This rules out possible faults due to
inaccurate stripping of the cable for assembly in the various components.
The 4 and 8-core FastConnect (FC) Industrial Ethernet
cables have a radially symmetric design, which allows the
use of a stripping tool FC stripping tool.
This allows plug-in connectors and patch outlets to be
quickly and easily connected on-site.
IE FC TP cable 2 x 2
The double shield makes it especially suitable for routing
through industrial areas with strong electro-magnetic
fields
Simple connection without special tools to the insulation
displacement contacts of the FC plugs
Integrated grounding concept can be achieved via the
outer shielding of the bus cable
Printed meter marks
Versatile application due to special bus cables
Network is immune to interference thanks to doubleshielded cables
Silicone-free and therefore suitable for use in the automotive industry (e.g. in paint shops)

10

Industrial Ethernet

outer sheath

foil shield
inner sheath

single core sheath

&DEOH

6WDQGDUG

copper core

,()&73

braided shield

G_IK10_XX_10033

Various cable designs are available for the construction of

structured Industrial Ethernet cabling in the harsh industrial environment.
The UL and Cat5 Plus-certified 4 and 8-core FastConnect
cables are available as:

Industrial Ethernet FC TP standard cable

IE FC TP cable 4 x 2
8-core FastConnect installation cable for cabling system
with Gigabit capability
User-friendly stripping technique with IE FC stripping
tool
Simple connection to IE FC RJ45 modular outlet by
means of insulation displacement technology
Time is saved thanks to easy and quick installation
Due to the 8-core cabling, it is possible today to implement 2 Fast Ethernet connections, but it will also be
possible to upgrade to a Gigabit Ethernet connection in
future
Noise-immune network due to a consistent grounding
concept
Possibilities of device networking with patch cables
and outlets
When using the outlets in the control cabinet or in a control room, pre-assembled RJ45 patch cables are available in
different versions (TP cord 4x2, TP cord 2x2 RJ45/sub D) for
connecting network components or terminals
For flexibly connecting devices with different data
rates, there is the Industrial Ethernet FC outlet RJ45
(10/100 Mbit/s) to 4-core Industrial Ethernet FC
cables, or the Industrial Ethernet FC modular outlet
(10/100/1000 Mbit/s) to 8-core Industrial Ethernet FC
cables for connecting to terminals or data and power
supply of remote stations (e.g. Access Point SCALANCE W).

Overview of electrical Industrial Ethernet cables

The following cables are offered for the various topologies,

requirements or application areas:
Cable type

Designation

Characteristics

Area of application

Twisted pair

TP cord

Patch cables, with RJ45,

15 or 9-pin sub D connectors, pre-assembled

For connection of stations to network components

within a control cabinet, up to 10 m cable length

Installation cables, insulation displacement

technology, sold by the
meter

For direct connection between network station and

component, used for structured cabling, fast and easy
connection of cables to the FC contacts

FastConnect

IE FC TP cable
2 x 2, 4-core for
Fast Ethernet
networks

- Standard bus cable with rigid cores and special

design for quick assembly; 4 rigid cores form a star
quad
- Flexible bus cable for the special application of
occasional motion control; four cores (stranded)
form a star quad
- Flexible, halogen-free cable for use in buildings
(FRNC= Flame Retardant Non Corrosive);
4 cores (stranded) form a star quad for occasional
movement
- Highly flexible bus cable for the special application
of constant motion control in a tow chain, e.g.
for continuously moving machine parts; 4 cores
(stranded) form a star quad
- Flexible cable for special continuous motion
applications in a trailing cable/festoon, e.g. in
crane systems; 4 cores (stranded) form a star quad
- Flexible cable for special applications in the food,
beverages and tobacco industries; 4 cores (stranded) form a star quad
- Bus cable for special marine applications; 4 cores
(stranded) form a star quad, halogen-free, certified
for marine applications
- Highly flexible bus cable for the special application
of continuous motion control, e.g. for use with
robots; stranded core
- For setting up Industrial Ethernet networks up to
100 m in combination with the IE FC modular
outlet and the TP cords
- For direct connection up to 60 m without patch
technology with IE FC RJ45 plug 4x2 and IE FC TP
cable 4x2 (AWG24)

IE FC TP standard cable GP 2x2

IE FC TP flexible cable GP 2x2

IE FC TP FRNC cable GP 2 x 2

IE FC TP trailing cable GP/

IE FC TP trailing cable 2x2

IE FC festoon cable GP 2 x 2

IE FC TP food cable 2 x 2

IE FC TP marine cable 2x2

IE TP torsion cable 2x2

IE FC TP cable
4 x 2, 8-core for
Gigabit Ethernet
networks

IE FC TP standard cable 4x2

(AWG 22)
IE FC TP cable 4x2 (AWG 24)

Connecting cable
M12-180/M12-180

Pre-assembled with two

4-pin M12 connectors
(IP65)

- 4-core connecting cable for IP65/IP67 components

Hybrid

IE hybrid cable

Hybrid cable for simultaneous transmission of

data (10/100 Mbit/s) and
energy (24 V/400 mA);
insulation displacement
technology, sold by the
meter

Industrial and office sector; for IE FC RJ45 modular

outlet and access point SCALANCE W with hybrid
connector

Power

Energy cable

Power line,
sold by the meter

For connection of signaling contact or 24 V DC

power supply

Industrial Ethernet

11

Plug-in connector for Industrial Ethernet

IE FC RJ45 plug 90/145/180

The compact and rugged design of the plug-in connectors
permits their use in the industrial environment and on all
devices from the office world.
The Industrial Ethernet FastConnect RJ45 plugs allow easy
and fast assembly of the 4-core Industrial Ethernet FC
twisted pair installation cables in the field (PROFINET-compatible).
They are available for
90
145 and
180 cable outlets
The rugged, industry-standard metal enclosure provides
optimum protection against interference for data communication.
The integrated 4 insulation displacement contacts make
the contacting of the FC cable versions easy and prevent
faults.
As the plug-in connector has no small parts that can be
lost, assembly is also possible under difficult conditions.
The FC RJ45 plugs allow point-to-point connections
(100 Mbit/s) to be implemented for Industrial Ethernet
between two terminals/network components up to 100 m
without patch cables.
By latching the connector to the device casing (e.g. with
SCALANCE X, CSM 377, SCALANCE S, S7-300 CPUs, CPs, or
ET 200S), the plug-in connection is relieved of tension and
bending strain.

Insert the cores according to the color-coding as far as the end stop
and press down on the contact lid

Perfect assembly of a cable with FastConnect takes less than 60 seconds

SCALANCE X multi-port switch with RJ45 connection technology

Industrial Ethernet FC RJ45 plug

Degree of protection IP20
Easy on-site assembly for implementing
direct device connections up to 100 m with
IE installation cables, 4 and 8-core without patch
systems

CP 443-1 Advanced with RJ45

connection technology

12

Industrial Ethernet

Plug-in connector for Industrial Ethernet

SCALANCE X208 with M12 connection technology

ET 200eco with M12 connection technology

ET 200pro with M12 connection technology

SCALANCE X with push-pull connection technology

Industrial Ethernet FC M12 plug PRO

Industrial Ethernet push-pull plug PRO

IP65/67 degree of protection

Easy assembly on-site for application-specific M12 plugin cables by means of FastConnect M12 plug-in connectors that can be assembled in the field (IE FC M12 plug
PRO, D-coded)

IP65/67 degree of protection

Data plug-in connector that can be assembled in the
field for IE FC TP and POF/PCF cables for transmitting
data up to 100 Mbit/s
PROFINET-compatible
Power plug-in connector suitable for on-site assembly
for transmitting 2x24 V between Industrial Ethernet
stations
The plug-in connectors make contact with the device
using a push-pull mechanism.

Industrial Ethernet

13

Patch technology for Industrial Ethernet

IE FC outlet RJ45

For time-saving and trouble-free connection of network

components or terminal equipment, various RJ45 patch
cables are available.

6

,(73&RUG

,()&
2XWOHW
5-

,()&5-
0RGXODU
2XWOHW
,QVHUW*(

,()&6WDQGDUG&DEOH[
0ELWVFRQQHFWLRQ

,()&6WDQGDUG&DEOH[

,()&
2XWOHW
5-

0ELWVFRQQHFWLRQ
,(73&RUG

Cabling example with IE FC outlet RJ45

IE FC RJ45 modular outlet

6

6&$/$1&(;

Due to the continuous rise in transmission rates for

Ethernet (10/100/1000 Mbit/s) and the service-neutral
cabling from the office sector, an 8-core cabling system is
also implemented by SIMATIC NET.
The Gigabit cabling system facilitates the transition from
the 4-core Industrial Ethernet FastConnect cabling system
to the 8-core, Gigabit cabling system.
The FC modular outlet can optionally be equipped with a
replaceable insert with:
2x RJ45 sockets for 100 Mbit/s systems
1x RJ45 socket for 1000 Mbit/s systems
1x 24 V, 1x RJ45 socket for 100 Mbit/s systems

,(73&RUG

(76

,()&5-
0RGXODU
2XWOHW
,QVHUW*(

,()&5-
0RGXODU
2XWOHW
,QVHUW)(
[0ELWV
FRQQHFWLRQ

,()&6WDQGDUG&DEOH[

In this way it is possible not only to implement individual

device connections, but also 100 Mbit/s double connections.
Just like the 4-core cabling system, this system also takes
into account the conditions in the field of industrial automation.
Assembly is particularly easy, as no special tools are
necessary (e.g. same FC stripping tool as for the 4-core
cabling system).

14

Industrial Ethernet

3&ZLWK&3

,()&5-
0RGXODU
2XWOHW
,QVHUW*(

*B,.B;;B

Rugged metal enclosure

Insulation displacement contacts for fastest connection
to Industrial Ethernet FC cables
By arranging several FC outlets RJ45 in a row, it is
possible to construct a patch panel with any density of
connections (e.g. 16 outlets on 19" width is possible)
DIN rail mounting and direct screw connection is
possible

6&$/$1&(;

[0ELWV
FRQQHFWLRQ

,()&5-
0RGXODU
2XWOHW
,QVHUW)(

,()&5-
0RGXODU
2XWOHW
,QVHUW*(

,(73&RUG

Cabling example with IE FC RJ45 modular outlet

3&PLW&3
*B,.B;;B

The FC outlet RJ45 is used for the transition from Industrial

Ethernet FC cables to pre-assembled TP cords by means of
a RJ45 socket.
It provides the following benefits:

Patch technology for Industrial Ethernet

Industrial Ethernet FC outlet RJ45

7
7
7
7
7
7

Simple connection method for 4-core installation

cables
10/100 Mbit/s transfer rates
Degree of protection IP20
Transition from rugged Industrial Ethernet FC
cables (2 x 2) to pre-assembled TP cords
Integrated insulation displacement contacts and
RJ45 socket
Patch fields are implemented with several RJ45 FC
outlets

Industrial Ethernet FC RJ45 modular outlet

7
7
7
7

Simple connection method for 8-core installation

cables
10/100/1000 Mbit/s transfer rates
Can be mounted inside or outside of control
cabinets due to IP40 degree of protection
Without swapping the cabling, it is possible to
upgrade from 100 to 1000 Mbit/s with a replaceable
insert
Basis for implementing structured cabling according
to ISO/IEC 24702

Industrial Ethernet

15

SOXJLQFRQQHFWRU

,(5-3OXJ352

16

Industrial Ethernet

*B,.B;;B

0
SRZHU
FRQQHFWRU
(QHUJ\&DEOH[

(QHUJ\&DEOH[

+\EULGFDEOH[[

,736WDQGDUG&DEOH
,73;36WDQGDUG&DEOH
,73;36WDQGDUG&DEOH
,73)51&&DEOH

,736WDQGDUG&DEOH
,73)51&&DEOH

,(73&RUG5-5-
,(73;3&RUG5-5-

,(73&RUG5-
,(73;3&RUG5-
,(73&RUG5-
,(73;3&RUG5-
,(73&RUG5-
,(73;3&RUG5-
,(73;3&RUG

,()&6WDQGDUG&DEOH*3[
,()&)OH[LEOH&DEOH*3[
,()&7UDLOLQJ&DEOH*3[
,()&7RUVLRQ&DEOH*3[
,()&7UDLOLQJ&DEOH[
,()&0DULQH&DEOH[

,()&6WDQGDUG&DEOH*3[$:*
,()&)OH[LEOH&DEOH*3[$:*

,()&6WDQGDUG&DEOH*3[$:*

3RZHUFDEOH

+\EULGFDEOH

,73FRQQHFWRU
FDEOH

,73FDEOHV

,(73&RUG[

,(73&RUG[

,()&&DEOH[

,()&&DEOH[

Electrical Industrial Ethernet network

Which connector fits which cable?

2SWLRQVIRUFRQQHFWLQJ,QGXVWULDO(WKHUQHWFDEOHVZLWKSOXJVWHUPLQDOVRU
GHYLFHV,(
HOHFWULFDO

,()&5-
0RGXODU2XWOHW

,()&2XWOHW5-

,()&5-3OXJ[

,()&5-3OXJ[

$FRGHG

'FRGHG

,3
K\EULGFRQQHFWRU

,73SOXJ
SLQSLQ

,(GHYLFHV
ZLWK6XE'FRQQHFWLRQ

'HYLFHV
ZLWK5-FRQQHFWLRQ

3RZHU3OXJ352

Optical Industrial Ethernet network

Overview of optical cables

Fiber-optic cables
The fiber-optic cable (FOC) is used for the transmission of
signals with the aid of electromagnetic waves within the
range of optical frequencies.
The light beam is guided by total reflection at the transition from the core to the fiber cladding, which has a lower
refractive index than the core.
The fiber-optic cable is provided with a coating. The term
fiber is often also used for fiber-optic cables.

7
7
7
7
7
7
7

Optical signal transmission

Tap-proof, as fiber-optic cables do not emit radiation
Unaffected by external noise fields
No grounding problems
Electrical isolation
Low weight
Simple cable laying due to rugged cable structure

Glass FOC with SC connector

For Industrial Ethernet, fiber-optic cables are offered with

fibers made of glass, PCF or POF:
Glass FOC:
Duplex cable for fiber-optic networks both indoors and
outdoors and for use on ships or offshore installations
for medium to long distances (3 km with multi-mode
and up to 26 km with single mode)
PCF-FOC:
Duplex cable for PCF networks both indoors and outdoors for smaller automation networks (50 m with POF,
100 m with PCF) with simple on-site assembly
POF-FOC:
Duplex cable for POF networks indoors for smaller automation networks (50 m with POF, 100 m with PCF) with
simple on-site assembly

PCF FOC with SC RJ connector

Industrial Ethernet

17

Optical Industrial Ethernet network

Overview of optical cables

Glass fiber-optic cables

Outer sheath
Single core
sheath
Hollow core

DUG&DEOH

Optical
fiber

G_IK10_XX_10030

)26WDQG

Strain relief using

aramide yarn

Plastic/PCF fiber-optic cable

PCF fiber-optic cables

Duplex cable for PCF networks in indoor and outdoor
applications
Electrical isolation of PROFINET/Ethernet devices
Protection of the transmission route against electromagnetic interference
Cable lengths up to 100 m possible
Rugged standard cables, designed for industrial use

Glass fiber-optic standard cable

Support
element
Single core sheath

QJ&DEOH

3&)7UDLOL

PCF fiber

Strain relief using

aramide yarn

PCF fiber-optic trailing cable

Strain relief using

aramide yarn

Industrial Ethernet

Outer sheath

OH

GDUG&DE

32)6WDQ

POF fiber

Single core sheath

POF fiber-optic standard cable

18

Fleece wrapping
with strain relief
elements

Hollow core

POF fiber-optic cables

Duplex cable for POF networks in indoor and outdoor
applications
Electrical isolation of PROFINET/Ethernet devices
Protection of the transmission route against electromagnetic interference
Cable lengths up to 50 m possible
Rugged standard cables, designed for industrial use

Outer sheath

G_IK10_XX_10031

SIMATIC NET plastic and PCF fiber-optic cables are used

for the construction of optical PROFINET and Industrial
Ethernet networks indoors. Devices with integral optical
interface (SC RJ connection system) are, for example,
SCALANCE X200-4P IRT, SCALANCE X201-3P IRT,
SCALANCE X202-2P IRT, SCALANCE X101-1POF, ET 200S.
Plastic and PCF-FOCs are easy to assemble on site using
SC RJ connectors. The maximum cable length between
two devices is 50 m for POF and 100 m for PCF fiber-optic
cables. PCF cables are also available pre-assembled with
2 SC RJ plugs.

G_IK10_XX_10179

Used for the optical Industrial Ethernet and PROFIBUS

network
Rugged construction for industrial applications both
indoors and outdoors
Halogen-free design for use in buildings
Trailing cable for special applications with forced motion
control
High interference immunity, as they are not sensitive to
electromagnetic interference
Available pre-assembled

Optical Industrial Ethernet network

Overview of optical cables

This overview shows which Industrial Ethernet

connector can be assembled with which cable.
Cable type

Designation

FastConnect

Characteristics

Area of application

Glass fiber, sold by the

meter or pre-assembled
with 4 BFOC or SC connectors

Laying in indoor and outdoor

areas

Plastic fiber-optic cable,

sold by the meter or
pre-assembled (PCF-FOC)
with 4 SC RJ connectors

Laying in indoor and outdoor

areas

FO standard cable GP (50/125)

FO ground cable (50/125)

FO trailing cable GP (50/125)

FO trailing cable (50/125)
SIENOPYR marine duplex
fiber-optic cable (62.5/125)

Fiber-optic
Plastic

POF standard cable GP 980/1000

POF trailing cable 980/1000

PCF standard cable GP 200/230

PCF trailing cable 200/230

PCF trailing cable GP 200/230

Cable versions:
- Rugged standard cable for universal applications
- Watertight cable in lateral and
longitudinal direction for use
outdoors; with non-metallic
rodent protection; laying in
the ground is possible
- Cable for use in tow chains
- Halogen-free, tread-resistant,
flame-retardant cable with
marine approval for laying in
ships and offshore installations

Cable versions:
- POF-FOC standard cable for
permanent cabling indoors up
to 50 m with PVC sheath
- POF-FOC trailing cable for
moving applications (e.g. trailing cable) up to 50 m with
rugged PUR sheath
- POF-FOC standard cable for
permanent cabling indoors
and outdoors up to 100 m
with rugged PVC sheath
- POF-FOC trailing cable for
high mechanical loads indoors
and outdoors up to 100 m
with rugged PUR sheath
- POF-FOC trailing cable for
lower mechanical loads indoors and outdoors up to
100 m with PVC sheath

Industrial Ethernet

19

,(6&5-3&)3OXJ352

20

Industrial Ethernet

*B,.B;;B

,(6&5-32)3OXJ352
3&)ILEHURSWLF
FDEOH

3&)6WDQGDUG&DEOH*3
3&)7UDLOLQJ&DEOH*3
3&)7UDLOLQJ&DEOH

)LEHURSWLFFDEOH
ZLWK
6&5-SOXJ

32))2&
wP
32)6WDQGDUG&DEOH*3
32)7UDLOLQJ&DEOH

3UHDVVHPEOHG)2&ZLWK6&5-
FRQQHFWRU

)LEHURSWLFFDEOH
ZLWK
6&SOXJ
3UHDVVHPEOHG)2&ZLWK6&FRQQHFWRU

)LEHURSWLFFDEOH
ZLWK
%)2&FRQQHFWRU

)LEHURSWLFFDEOH
wP

),%(5237,&VWDQGDUGFDEOH
,1'225)LEHU2SWLFLQGRRUFDEOH
)OH[LEOH)LEHU2SWLFWUDLOLQJFDEOH
6,(123<5PDULQHGXSOH[ILEHURSWLF
FDEOH

3UHDVVHPEOHG)2&ZLWK%)2&
FRQQHFWRU

)LEHURSWLFFDEOH
wP

)26WDQGDUG&DEOH*3
)27UDLOLQJ&DEOH
)27UDLOLQJ&DEOH*3
)2*URXQG&DEOH

Optical Industrial Ethernet network

Which connector fits which cable?

2SWLRQVIRUFRQQHFWLQJ,QGXVWULDO(WKHUQHWFDEOHVZLWKSOXJVWHUPLQDOVRUGHYLFHV
2SWLFDO

%)2&FRQQHFWRU

,(GHYLFHV
ZLWK%)2&FRQQHFWLRQ

6&SOXJ

,(GHYLFHV
ZLWK6&FRQQHFWLRQ

6&5-SOXJ

,(GHYLFHV
ZLWK6&5-FRQQHFWLRQ

PROFIBUS
network selection criteria

Criteria

Electrical network

Optical network

RS 485
according to
IEC 61158/
61784

IEC 61158-2
(PA)

Plastic

PCF

Glass

n n n n

EMC

n n n ,

1)

n n n ,

n n n n

n n n n

Inter-building networking

n n , ,

1)

n n , ,

n n n n

n n n ,

Range

n n , ,

2)

n n , ,

n n n n

n n , ,

n n n n

Suitability for high

transmission rates

n n n ,

4)

n n n ,

n n n n

n n n n

Simple connector
assembly

n n n n

n n n n

n n n ,

n n , ,

Simple cable laying

n n n ,

n n n ,

n n , ,

n n , ,

n n , ,

Equipotential bonding
measures required

Yes

Yes

No

No

No

Cables for special

applications

n n n n

n , , ,

n , , ,

n , , ,

n n , ,

Use with moving

stations

n n , ,

, , , ,

, , , ,

n n , ,

Use in intrinsically safe

environment

n n n n

1) Lightning protection measures

required
2) Depending on the transmission
rate
3) Trained personnel and special tool
required
4) Careful laying required
5) Outer conductor required
(on request)

n
n
n
n
,

n
n
n
,
,

n
n
,
,
,

n
,
,
,
,

suitable
partially suitable

not applicable

5)

3)

n n n n

n , , , 3)

G_IK10_XX_50010

The type of network (electrical or optical, copper or

fiber-optic cables) is determined by the environmental conditions in which it is
to be constructed.

PROFIBUS

21

Network selection criteria

Criteria

Transition media

Electrical network

Optical network

Electrical PROFIBUS

with OLM

with integr. interface/

OBT

9.6 km 5)

90 km

9.6 km

up to 1 km 3)

up to 15 km 2)

up to 300 m 2)

all

all

DP

Plastic 1)
PCF
Glass
Shielded two-core cable

Distances

max. network size

between two nodes

Topology

Bus
Line
Tree
Ring

Transmission protocols
Connection of
nodes via

OLM
4)

Integrated interfaces
Bus terminal
Bus connector

1)
2)
3)
4)
5)

22

PROFIBUS

Plastic optical fiber is also referred to as polymer optical

fiber (POF)
Depending on type of cable used
Depending on data rate used and performance
Integrated interfaces (ET 200M, ET 200X)
for PROFIBUS PA 1.9 km

suitable
Irrelevant to this application

G_IK10_XX_50133

Electr. network segments

connectable

Electrical PROFIBUS network

There are different networking options for PROFIBUS networks, depending on the respective application:
Electrical data transmission by means of shielded
twisted-pair cables with circular cross-section available
as standard type, with PE or PUR sheath, halogen-free
design, cables for use underground, in tow chains or
specially for hazardous areas. With the PROFIBUS
FastConnect system, the PROFIBUS copper cables can
be quickly and easily assembled on-site.

Foil shield

Outer sheath

Inner sheath
DUG&DEOH
6)&6WDQG
352),%8

Copper core

Optical data transmission via fiber-optic cable with glass

or plastic fibers for indoor or outdoor applications, as
trailing cable or as halogen-free version.

Single core sheath

Braided shield

PROFIBUS FC standard cable

PROFIBUS bus cables

The design of the FastConnect (FC) bus cables is radially
symmetric and allows the use of a stripping tool. This
means that the bus connectors can be assembled quickly
and easily.

PB FC plug 180
7
7

7
7

A wide variety of possible applications thanks to

special bus cables (e.g. underground cable, trailing
cable, use in hazardous areas)
Network is immune to interference thanks to
double shielded cables and a uniform grounding
concept
Time saving due to simple and fast connector
assembly with FastConnect cables
Silicon-free, therefore particularly suitable for use
in the automotive industry (e.g. on paint shop
conveyors)
Flame-retardant bus cable (halogen-free)
Easy length measurement thanks to printed meter

PROFIBUS

23

Electrical PROFIBUS network

Overview of PROFIBUS bus cables

The following applies for all PROFIBUS bus cables:

Due to the double shielding, they are particularly suitable for laying in industrial environments subject to
electromagnetic interference.
Cable type

Designation

A consistent grounding concept can be implemented via

the outer sheath and the ground terminals of the bus
terminal.
The printed meter marks simplify assembly.
Characteristics

Area of application
For the construction of PROFIBUS
networks, the following
different types of silicon-free
cables are offered for the
different applications:

Bus cables
with
FastConnect
technology

Quick and easy connector assembly with the

aid of the stripping tool.
Shielded and twisted
2-core cables constructed
with radial symmetry.
PROFIBUS
FC standard cable GP
FC robust cable

- Standard cable for universal

applications
- Special cable for chemically
and mechanically demanding
environments
- Special cable for the food,
beverages and tobacco industries
- Special cable for routing underground
- Special cable for use in tow
chains
- Trailing cable for moving machine parts (stranded wire)
- Halogen-free and flame-retardant cable
- Bus cable for fieldbus systems
compliant with IEC 61158-2
(hazardous and non-hazardous

FC food cable

FC ground cable
FC flexible cable
FC trailing cable
FC FRNC cable GP
FC process cable GP

Bus cables
without
FastConnect
technology

Shielded, twisted-pair
cable with circular crosssection; sold by the meter
PROFIBUS
Festoon cable GP
Torsion cable

ECOFAST hybrid cable GP

SIENOPYR marine cable

24

PROFIBUS

- Special cable for festoon suspension

- Special cable for use on
machine parts where the cable
is subject to torsion (stranded)
- Hybrid cable for data transmission and voltage supply to
ECOFAST stations (stranded)
- Halogen-free, tread-resistant,
flame-retardant cable with
marine approval for permanent
laying in ships and offshore
installations

Cable type

Designation

Characteristics

Area of application

Plug-in
cables

PROFIBUS
Connecting cable 830-1T

Twisted-pair conductors (cores of stranded

copper) with a braided
shield and a 9-pin sub D
connector at both ends.
Both ends of the cable are
terminated with a resistor
combination (cannot be
switched off).

Via the PROFIBUS 830-1T

connecting cable, the connection
between an electrical PROFIBUS
interface and a PROFIBUS
station (OLM, OBT and end
station) can be established with
up to 12 Mbit/s.

PROFIBUS
Connecting cable 830-2

PROFIBUS standard bus

cable with two
9-pin connectors (90
angled), pre-assembled.
One connector of the preassembled connecting
cable is equipped with
a programming device
interface.

The connecting cable 830-2 is

used for connecting PROFIBUS
stations (e.g. HMI) to PLCs at
transmission rates of up to
12 Mbit/s.

PROFIBUS
M12 connecting cable

Pre-assembled connecting cable (PROFIBUS FC

trailing cable) with two
5-pin M12 plugs/sockets

The PROFIBUS M12 connecting

cable is used to connect
PROFIBUS nodes (e.g. SIMATIC
ET 200) with degree of protection
IP65

7/8" connecting cable

Pre-assembled connecting cable with two 5-pin

7/8" plugs/sockets

The 7/8" connecting cable is used

for supplying power to PROFIBUS
stations (e.g. SIMATIC ET 200)
with degree of protection IP65

Hybrid cable with two

energy cores
(1.5 mm), sold by the
meter

The hybrid cable is used for

supplying data and energy to the
ET 200pro

Hybrid

PROFIBUS hybrid standard

cable GP

Cable versions:
- Standard cable for universal
applications
- rugged, trailing-type and weld
spatter-proof hybrid cable, e.g.
for use in welding cells

PROFIBUS

25

Optical PROFIBUS network

Overview of optical cables

Fiber-optic cable (FOC)

Advantages
Optical signal transmission
Tap-proof, as fiber-optic cables do not emit radiation
Unaffected by external noise fields
No grounding problems
Electrical isolation
Low weight
Easy to lay
For PROFIBUS, fiber-optic cables with glass and plastic
fibers are offered for indoor and outdoor applications as
well as for use on ships and offshore installations:
Glass fiber-optic cables
Used for the optical Industrial Ethernet and PROFIBUS
network
Rugged construction for industrial applications both
indoors and outdoors
Halogen-free design for use in buildings
Trailing cable for special applications with forced motion
control
High interference immunity, as they are not sensitive to
electromagnetic interference
Available pre-assembled

Outer sheath
Single core
sheath
Hollow core

DUG&DEOH

)26WDQG

Optical
fiber

G_IK10_XX_10030

The fiber-optic cable (FOC) is used for the transmission of

signals with the aid of electromagnetic waves within the
range of optical frequencies.
The light beam is guided by total reflection at the transition from core to fiber cladding, which has a lower refractive index than the core.
The fiber-optic cable is provided with a coating. The term
fiber is often also used for fiber-optic cables.

Strain relief using

aramide yarn

Glass fiber-optic standard cable

Strain relief using

aramide yarn

Outer sheath

Single core sheath

QJ&DEOH

32)7UDLOL

Fleece wrapping
with strain relief
elements

POF fiber

POF fiber-optic trailing cable

Support
element

Outer sheath

Single core sheath

QJ&DEOH

PCF fiber

Strain relief using

aramide yarn
Hollow core

PCF fiber-optic trailing cable

26

PROFIBUS

Fleece wrapping
with strain relief
elements

G_IK10_XX_10031

3&)7UDLOL

Plastic/PCF fiber-optic cable

Assembly made easy

SIMATIC NET plastic and PCF fiber-optic cables are used for
the construction of optical PROFIBUS networks or for optical linking of segments using RS485 technology in indoor
and outdoor applications. They can be assembled on site
using 2x2 simplex or 2x2 BFOC connectors. The maximum
cable length between two DP devices is 300 m. Longer
cable lengths up to 400 m can be implemented with
PCF-FOC.

PCF fiber-optic cables are easily assembled on site with

2 x 2 simplex connectors or 2 x 2 BFOC connectors using
the PCF fiber-optic cable termination kit.
Two versions of the assembly case are available for PCF
fiber-optic cables:
Assembly case for HP simplex connectors;
for local assembly of HP simplex connectors;
comprising a stripping tool, buffer stripping tool,
Kevlar cutters, crimping tool, fiber breaking tool and
microscope
Assembly case for BFOC connectors;
for local assembly of BFOC connectors;
comprising a stripping tool, buffer stripping tool,
Kevlar cutters, fiber breaking tool, and microscope.

POF fiber-optic cables

Electrical isolation of PROFIBUS devices and PROFIBUS
segments
Protection of the transmission route against electromagnetic interference
Cable lengths up to 80 m using plastic fiber-optic cables
Rugged standard fiber-optic cables, designed for industrial use
PCF fiber-optic cables
Electrical isolation of PROFIBUS devices and PROFIBUS
segments
Protection of the transmission route against electromagnetic interference
Up to 400 m using PCF fiber-optic cables
Rugged standard fiber-optic cables, designed for industrial use
SIMATIC NET PCF fiber-optic cables are used to construct
optical indoor and outdoor PROFIBUS DP networks. Their
special construction facilitates connector assembly on
site. PCF fiber-optic cables can readily be assembled on
site using 2 x 2 simplex connectors or 2 x 2 BFOC connectors (bayonet fiber-optic connectors). The maximum cable
length between two DP devices is 300 m and between two
OLMs 400 m. Two assembly cases are offered for this:
Assembly case for BFOC connectors
Assembly case for simplex connectors

The termination kits provide the following benefits

Simple installation of the unassembled cable in industrial
plants
Flexible connector assembly on PCF FOCs possible on site
(HP simplex, BFOC connector)
Prevention of faults by simply checking the assembled
connectors on site using a microscope
Simple repair of PCF FOC in the field by laying new
PCF cable

Simplex connector

BFOC connector

PROFIBUS DP devices with integrated optical interface (simplex connection technology) are e.g. OBT, CP 342-5 FO,
CP 5613 FO, IM 153-2 FO, IM 467 FO.

PROFIBUS

27

Optical PROFIBUS network

Overview of optical PROFIBUS bus cables

Cable type

Designation

Fiber-optic

Characteristics

Area of application

Glass fiber, sold by the

meter or pre-assembled
with 4 BFOC or SC connectors

Laying in indoor and outdoor

areas

Cable versions:
- Rugged standard cable for
universal applications
- Watertight cable in lateral and
longitudinal direction for use
outdoors; with non-metallic
rodent protection; laying in
the ground is possible
- Cable for use in tow chains
- Halogen-free, tread-resistant,
flame-retardant cable with
marine approval for laying in
ships and offshore installations

FO standard cable GP (50/125)

FO ground cable (50/125)

FO trailing cable GP (50/125)

FO trailing cable (50/125)
SIENOPYR marine duplex
fiber-optic cable (62.5/125)

PROFIBUS plastic
fiber-optic

Duplex core

Standard cable
PROFIBUS PCF plastic fiber-optic
standard cable

28

PROFIBUS

Plastic/PCF fiber-optic
cable; sold by the meter
or pre-assembled.

Plastic and PCF fiber-optic cables

are used for the construction of
optical PROFIBUS DP networks in
indoor applications.
- Up to 80 m with low mechanical loads, e.g. laboratory structures
- Up to 50 m, with Kevlar tension
elements
- Up to 400 m, with Kevlar tension elements

Connection components for PROFIBUS

Electrical network

Optical network

IEC 61158-2
(PA)

with OLM

with integral
interface/OBT

Network topology

Bus, tree

Bus, tree

Linear, star, ring

Linear

Transmission media

Shielded
two-wire line

Shielded two-wire line

for intrinsically safe and
non-intrinsically safe
areas

Plastic FOC
PCF FOC
Glass FOC

Plastic FOC
PCF FOC

Tools
and accessories

FastConnect
stripping tool

FastConnect
stripping tool

Tools for assembling

BFOC connectors for
plastic FOC

Tools for assembling

simplex connectors for
plastic FOC

Connection method

Bus connector

SpliTConnect system

BFOC connector

Simplex connector

Connection
components

Bus terminal

SpliTConnect system

OLM

OBT

Pre-assembled
cables

Connecting cable 830-1T

Connecting cable 830-2

---

INDOOR cable
with BFOC
Standard glass cable
with BFOC
Trailing cable
with BFOC
Standard PCF cable
with BFOC
Standard plastic cable
with BFOC

Standard PFC cable with

simplex connectors and
insertion tool

Lightning protection

Basic protection
Low-voltage protection

To be implemented
by means of
structural measures

Not required

Not required

Electrical
network segment
can be connected via

repeater

---

Optical link module

(OLM)

Optical bus terminal

(OBT)

Diagnostics tool

Hardware test unit

BT 200

Not available

Signaling contact and

internal measuring
sockets;
Level measuring unit
upon request

Level measuring unit

upon request

Documentation

Manual for
PROFIBUS networks

Manual for
PROFIBUS networks

Manual for
PROFIBUS networks

Manual for
PROFIBUS networks

G_IK10_XX_50016

RS 485 according to
IEC 61158/EN 50170

PROFIBUS

29

2SWLFDO

30

PROFIBUS

6LPSOH[
FRQQHFWRU

3%GHYLFHV
ZLWKVLPSOH[
LQWHUIDFH
&RQQHFWLQJ
FDEOHV
(&2)$67
FDEOH

+\EULGFDEOH

3RZHUFDEOH
352),%86)&
%XVFDEOH
352),%863$
%XVWHUPLQDO

)LEHURSWLFFDEOH
wP

)LEHURSWLFFDEOH
wP
3&)ILEHURSWLF
FDEOH
wP
32))2&
wP

&RQQHFWLQJFDEOH
&RQQHFWLQJFDEOH7
352),%860SOXJLQFDEOH

(&2)$67+\EULG&DEOH
(&2)$67+\EULG&DEOH*3

352),%86+\EULG6WDQGDUG&DEOH*3
352),%86+\EULG5REXVW&DEOH

3RZHU&DEOHb[bb

3%)&3URFHVV&DEOH

0EXVWHUPLQDO

)26WDQGDUG&DEOH*3
)27UDLOLQJ&DEOH
)27UDLOLQJ&DEOH*3
)2*URXQG&DEOH
),%(5237,&VWDQGDUGFDEOH
,1'225)LEHU2SWLFLQGRRUFDEOH
)OH[LEOH)LEHU2SWLFWUDLOLQJFDEOH
6,(123<5PDULQHGXSOH[ILEHURSWLF
FDEOH
3&)6WDQGDUG&DEOH*3
3&)7UDLOLQJ&DEOH
3&)7UDLOLQJ&DEOH*3

3ODVWLFILEHURSWLFVWDQGDUGFDEOH

3UHDVVHPEOHG)2&ZLWKVLPSOH[FRQQHFWRU

)LEHURSWLFFDEOH
ZLWK
6LPSOH[FRQQHFWRU

)LEHURSWLFFDEOH
ZLWK
%)2&FRQQHFWRU

352),%86
EXVFDEOHV

352),%86)HVWRRQ&DEOH
352),%86)OH[LEOH&DEOH

3UHDVVHPEOHG)2&ZLWK%)2&FRQQHFWRU

352),%86)&
EXVFDEOHV

352),%86)&6WDQGDUG&DEOH
352),%86)&6WDQGDUG&DEOH,6*3
352),%86)&5REXVW&DEOH
352),%86)&)RRG&DEOH
352),%86)&*URXQG&DEOH
352),%86)&)51&&DEOH
352),%86)&7UDLOLQJ&DEOH

(OHFWULFDO

*B,.B;;B

(OHFWULFDO

Electrical and optical PROFIBUS network

Which connector fits which cable?

2SWLRQVIRUFRQQHFWLQJ352),%86FDEOHVZLWKSOXJVWHUPLQDOVRUGHYLFHV
2SWLFDO

3%
)DVW&RQQHFW
FRQQHFWRU

3%EXV
FRQQHFWRU

(&2)$67
FRQQHFWRU

3%0SOXJ
VRFNHW
%FRGHG

3RZHU
FRQQHFWRU

3%GHYLFHV
ZLWK6XE'
0
LQWHUIDFH

(7SUR

%XVWHUPLQDO
0

6SOL7&RQQHFW
V\VWHP

%)2&
FRQQHFWRU

3%GHYLFHV
ZLWK%)2&
FRQQHFWLRQ

The right cable for every application

In order to maintain fault-free, long-term operation of
the industrial data networks, every user must precisely
analyze the type of environment where the cable will be
used prior to installation. This influences the selection of
the correct type of cable. Depending on whether the cable
should be used in fixed or moving applications (e.g. use in
tow chains), you can select between cables with rigid or
flexible cores. In addition the outer sheath of a cable must
protect the internal construction against environmental
influences. By adding UV stabilizers to the material for the
sheaths, the cables can also be laid in outdoor applications
(e.g. on cable racks).
Special approvals
SIMATIC NET cables are also certified for special applications, e.g. for ships and offshore facilities, or for the
American and Canadian markets (UL listing such as OFN/
OFNG for FOC or CM/CMG for copper cables).
Current information on certifications can be found in the
technical data for the corresponding products under:
www.siemens.de/automation/mall
Note
You can order components supplementary to the
SIMATIC NET cabling system from your local contact.
Technical advice on this subject is available from:
J. Hertlein, IA SE PS
Tel.: + 49 911/750 44 65
Fax: + 49 911/750 99 91
E-mail: [email protected]

Sheath material

Application

PVC (polyvinyl chloride):

Material with good mechanical properties and
resistance to chemicals

Standard for industrial applications for indoor and outdoor areas

(e.g. in cable racks)

PUR (polyurethane):
Halogen-free material
with excellent mechanical strength and resistance to chemicals
(abrasion-resistant)

Cables subject to considerable

movement (tow chains), with
high mechanical or chemical
stresses, for harsh industrial
environments

PE (polyethylene):
Particularly resistant to
moisture affecting the
cable continuously

Use in damp or humid environments both indoors (e.g. in food

and beverage industry) and outdoors and for laying directly into
the ground

FRNC (Flame Retardant

Non Corrosive):
Material which behaves
well in a fire, mostly
self-extinguishing, which
does not produce any
harmful gases in the
event of a fire; serious
secondary damage is
avoided.

Standard applications with high

fire safety requirements

The elasticity of polyurethane is retained over a wide

temperature range (-20 C to +80 C).
In special applications such as welding robots in the
automotive industry, the resistance to welding sparks
can be further increased by a radial meshing of the
material.

PROFIBUS

31

Further information
More on SIMATIC NET:
www.siemens.com/simatic-net
Information and ordering platform:
www.siemens.com/automation/mall
All about FastConnect:
www.siemens.com/fastconnect

Siemens AG
Industry Sector
Postfach 48 48
90026 NRNBERG
GERMANY

www.siemens.com/automation

32

Introduction

Subject to change without prior notice

Order No.: 6ZB5530-1AW02-0BA1
3P.8101.49.02 / Dispo 26000
BR 1208 4. WE 32 En
Printed in Germany
Siemens AG 2008

The information provided in this brochure contains descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective
characteristics shall only exist if expressly agreed in the terms of contract. Availability and technical specifications are subject to change
without prior notice.
All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their
own purposes could violate the rights of the owners.