CT 222/E
UNEQUALLED HIGH
TURNDOWN (1:500)
LOW-NOISE TRIM
REFLUX 919 CONTROL
ABSOLUTE TIGHT SHUT OFF
UNEQUALLED HIGH TURNDOWN
(1:500)
LONG TRIM LIFE
EASY MAINTENANCE
STANDARDIZED PARTS
LOW-NOISE TRIM
HIGH CAPACITY
HIGH ACCURACY
HIGH STABILITY
PRESSURE CLASSES: S150,
S300, S600
The Reflux 919 Control is a pneumatic control valve,
specifically designed for use of natural gas, commonly operated by a direct acting type diaphragm
actuator (mod. 200) or reverse acting type diaphragm actuator (mod. 300).
- The control loop is 6-30 psig: other signals available on application
- The absolute tight shut off is obtained by the soft
seated patented Fiorentini design
- Very high rangeability due to special plug guiding
(1:500)
- The actuator design has a special balanced valve
plug for minimum actuator requirement
- Maximum inlet pressure 85 bar
- Maximum pressure drop 83 bar
- Nace MR 01/75 version available on request
- Retrofitting capability by built-in special silencer
and Fiorentini patented channel flow trim.
Table 1 - Capacity information
Size
10
Kg
605
2.335
5.194
8.416
17.471
27.282
38.425
Cg
575
2.200
4.937
8.000
16.607
25.933
36.525
Cv
18
69
154
250
519
810
1141
CHOOSING THE SIZE OF THE VALVE
Choise of the valve is usually on the basis of Cg valve
and KG flow rate coefficients. Cg coefficient corresponds numerically to the value of air flow in SCF/H in
critical conditions with full open valve operating with
an upstream pressure of 1 psia at a temperature of
15C. KG coefficient corresponds numerically to the
value of natural gas flow rate in Stm/h in critical conditions with full open valve operating with an upstream
pressure of 2 bar abs at a temperature of 15C.
Flow rates at full open position and various working
conditions, are bound by the following formule where:
(valid for Pe < 2 Pa)
1.2 in critical conditions:
(valid for Pe 2 Pa)
Pe = inlet pressure in bar (abs)
Pa = outlet pressure in bar (abs)
Q = flow rate in Stm/h
KG, Cg = valve coefficients
Q = 0.525 Cg Pe (valid for Pe 2 Pa)
2 Viceversa, when values of Pe, Pa and Q are known
calculate the values of Cg or KG with:
1. When valves Cg and KG and values of Pe and Pa
are known
2.1 in non critical-conditions:
1.1 in non critical conditions:
(valid for Pe < 2 Pa)
(valid for Pe < 2 Pa)
(valid for Pe < 2 Pa)
As already mentioned Cg and KG values are related
to a fully-open valve.
Diagram of fig. 1 gives the values of Cg and KG
coefficients in function of plug lift. Both coefficient
values and plug lift are expressed in percentage of
the maximum value.
2.2 in critical conditions:
VALVE CHARACTERISTICS Cg and KG
Cg, Kg%
100
90
80
(valid for Pe 2 Pa)
70
A oversizing of 20% on calculated values is raccomanded.
60
Cg formulae give flow rate values more correct
while KG formulae give values 5% higher than real
ones only in noncritical conditions.
In the case of noise limitation level a speed at the
outlet flange of 130 m/sec. it is also raccomanded.
Above formulae are valid for natural gas with a relative specific gravity of 0,61 compared to air and
temperature of 15C at inlet.
For gases with different relative specific gravity (S)
and temperature t (in C), value of flow rate calculated as above, must be adjusted multiplying by:
40
50
30
20
10
0
0
10
20
30
40
50
Fig. 1
60
70
80
90
100
Opening
VALVE CHARACTERISTICS
Modified equal percent, inherent linear (easily) characterizable with positioner CAM)
Table 2- STD MATERIAL INFORMATION
PART
MATERIAL
SEAT RING
Vulcanized nitril TN040
BODY
VALVE STEM
ASTM A216 WCB
AISI 416
PISTON
Carbon steel
DIAPHRAGM PLATES
Carbon stell
SEALS
Viton
G
A
H
P
DN
DN
Direct action version
OVERALL DIMENSIONS in mm. WEIGHTS
25
50
80
100
150
200
250
10
ANSI 150
183
254
298
352
451
543
673
ANSI 300
197
267
317
368
473
568
708
ANSI 600
Size
210
286
336
394
508
609
752
550
580
615
645
670
720
830
A*
503
533
568
598
657
707
817
100
130
150
190
225
265
340
375
375
375
375
495
495
630
130
160
200
250
275
320
440
640
660
715
755
755
820
930
G*
593
613
668
708
742
807
917
650
710
765
835
895
985
1170
H*
603
663
718
788
882
972
1157
170
200
235
265
300
350
460
* dimensions only for direct action
Weights - Kgf
ANSI 150
35
53
75
117
210
330
ANSI 300
40
58
85
140
280
390
600
ANSI 600
41
60
90
145
300
420
700
G
A
H
P
DN
DN
Direct action version
OVERALL DIMENSIONS in mm. WEIGHTS
25
50
80
100
150
200
250
10
ANSI 150
183
254
298
352
451
543
673
ANSI 300
197
267
317
368
473
568
708
ANSI 600
Size
210
286
336
394
508
609
752
750
805
885
955
955
1055
1330
A*
703
758
838
908
942
1042
1317
100
130
150
190
225
265
340
375
375
375
375
495
495
630
130
160
200
250
275
320
440
840
885
985
1065
1040
1155
1430
G*
793
838
938
1018
1027
1142
1417
850
935
1035
1145
1180
1320
1670
H*
803
888
988
1098
1167
1307
1657
370
425
505
575
585
685
960
* dimensions only for direct action
Weights - Kgf
ANSI 150
58
93
135
207
405
620
ANSI 300
63
108
167
240
480
665
1000
ANSI 600
64
112
175
263
500
705
1130
CT 222/E
I dati sono indicativi e non impegnativi. Ci riserviamo di apportare eventuali modifiche senza preavviso.
The data are not binding. We reserve the right to make modification without prior notice.
Pietro Fiorentini S.p.A.
I-20124 MILANO
I-36057 ARCUGNANO (VI)
I-80142 NAPOLI
Italy - Via Rosellini, 1 - Phone +39.02.6961421 (10 linee a.r.) - Telefax +39.02.6880457
E-mail: [email protected]
Italy - Via E. Fermi, 8/10 - Phone +39.0444.968511 (10 linee a.r.) - Telefax +39.0444.960468
E-mail: [email protected]
Italy - Via B. Brin, 69 - Phone +39.081.5544308 - +39.081.5537201 - Telefax +39.081.5544568
ASSISTENZA POST-VENDITA E SERVIZIO RICAMBI: - SPARE PARTS AND AFTER-SALES SERVICE:
I-36057 ARCUGNANO (VI) - Italy - Via E. Fermi, 8/10 - Phone +39.0444.968511 (10 linee a.r.) - Telefax +39.0444.968513 - E-mail: [email protected]
Edigraf srl 03/2000
UFFICI COMMERCIALI: - OFFICES:
