Scribd
Upload
404 views

Front End Loader PDF

Only persons who hold the appropriate National Certificate of Competency are to operate a tractor. Restriction does not apply to a person who is authorised to carry out maintenance or repairs to a tractor or an attachment. Check fuel, hydraulic oil, engine oil, transmission oil, coolant and battery. Check condition and tension of tracks (sag between 2.5mm and 3.8mm) remove any mud lumps from treads. Check rams, hoses and connections for splits, leaks or fractures

Uploaded by

cityofdarwingis
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
404 views

Front End Loader PDF

Only persons who hold the appropriate National Certificate of Competency are to operate a tractor. Restriction does not apply to a person who is authorised to carry out maintenance or repairs to a tractor or an attachment. Check fuel, hydraulic oil, engine oil, transmission oil, coolant and battery. Check condition and tension of tracks (sag between 2.5mm and 3.8mm) remove any mud lumps from treads. Check rams, hoses and connections for splits, leaks or fractures

Uploaded by

cityofdarwingis
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SAFE WORK PROCEDURES

FRONT END LOADER


SPECIAL INSTRUCTIONS:
1.
Only persons who hold the appropriate National Certificate of Competency and who have been authorised to do so are to operate a tractor.
2.
This restriction does not apply to a person who is authorised to carry out maintenance or repairs to a tractor or an attachment.
Task sequence
1. Pre-start checks

Identified hazards in task


Roll-over protection
Fuel and fluids
Tyres (rubber tyred units)
Tracks (tracked units)
Bucket

2. Entry and exit

Hydraulics
Slipping and falls

3. Operator position

Seating
Seat belt
Controls
Cabin (if fitted)

4. Controls

Mirrors
Lights and alarms
Steering and brakes

5. Travel

Hydraulic controls
Passengers
Loss of control
Overturning

SWP99 Version 1.3

Key processes to be followed


Tractors must be fitted with an approved roll-over protective structure
(ROPS) unless specifically exempted by the appropriate statutory authority.
Check fuel, hydraulic oil, engine oil, transmission oil, coolant and battery.
Check tyre condition and pressures; remove any mud lumps from treads.
Check condition and tension of tracks (sag between 2.5mm and 3.8mm).
Inspect for worn or missing teeth or worn cutting edges.
Check arms and connections for excessive wear.
Check rams, hoses and connections for splits, leaks or fractures.
Steps and ladders should be of a non-slip type.
Hand holds must be provided to assist operator to maintain 3 points of
contact at all times while mounting or dismounting tractor.
Seat should be well-sprung and adjustable to allow operator to maintain a
comfortable operating position.
Seat belt must be fitted, correctly adjusted and worn when machine is used.
All levers and gauges must be clearly identified, within easy reach and be
easily read. Preferred orientation should be such that all needles are in
vertical position during correct operating conditions.
Adequate ventilation must be provided.
Exhaust must be placed so as to not allow fumes to enter cabin.
Clean and adjust mirrors before commencing work, and if bumped.
Test all lights, indicators, horn and reversing alarm.
Test steering both ways. Check braking and park brake operation.
Lock separated brake pedals together if travelling.
Test all hydraulic operations before loading bucket.
Passengers must not be carried unless proper seat with seat belt fitted.
Do not travel at speeds which may cause control to be lost over bumps, etc.
Carry bucket as close to ground as possible and racked back for visibility.
Avoid driving over obstacles, ditches, drains, etc which could affect control.
Avoid travel across slope on a steep incline.
Avoid sharp turns or turning at speed.

ASSA Pty Ltd

ThisSafeWorkProcedurewasgeneratedon29/11/2013byASSAPtyLtdforuseonlybyCityofDarwin.

Precautions / PPE required

Wear eye and hand protection.


Wear gloves.

Adjust seat to suit personal need.


Seat belt must be worn when
driving and operating.

Do not drive machine if faulty.

Do not carry passenger unless


dedicated seat is provided.

Slow down to turn.

www.assaohs.com.au

Page 1 of 2

SAFE WORK PROCEDURES


FRONT END LOADER
Task sequence
6. Operation

Identified hazards in task


Overturning

Moving parts, crush injury


Dust, falling objects, noise

7. Parking

Stability

Security
8. Maintenance

Burns
Over-exertion/strain injury
Crush injury from falling
object

Key processes to be followed


Reduce speed when travelling with load in bucket.
Carry bucket close to ground and racked back for stability and visibility.
Approach unit to be loaded at right angles, do not raise bucket until ready to
empty.
Avoid travelling and turning with bucket in raised position.
Do not load bucket in excess of working load limit of loader.
Nip and pinch points on articulated rollers must be highlighted and signed.
Appropriate protective equipment should be used where hazards may be
encountered during operation.
Foot protection must be worn on sites where a hazard to feet may exist.
Park on level ground if possible.
Position machine up and down the slope if parking on sloping ground.
Apply handbrake, place transmission in neutral or park position.
Lower bucket fully with front cutting edge flat on ground.
Switch off engine, remove keys and lock cabin before leaving machine
unattended.
Allow engine to cool before removing radiator cap.
Rear tyres may be water-filled as ballast always have valve stem at top
position to check pressure or inflate tyre. Place valve at bottom position to
drain water from tyre. Use mechanical aids to remove or replace assembly.
Use mechanical aid to remove or replace counterweights.

Precautions / PPE required

NOTE: Wet materials will weigh


more per unit than dry material.
Keep clear of nip and pinch points
on articulated loaders.
Head, eye and hearing and foot
protection may be required.

Never leave keys in ignition if


machine is unattended.
Hand protection should be worn.

Wear type 1 footwear.

PRECAUTIONS:
The following precautions are to be observed, and suitable
safety signs as indicated should be displayed in areas where
these procedures are carried out.

SWP99 Version 1.3

ASSA Pty Ltd

ThisSafeWorkProcedurewasgeneratedon29/11/2013byASSAPtyLtdforuseonlybyCityofDarwin.

www.assaohs.com.au

Page 2 of 2

You might also like