Wood Group
Surface Pumps
API 610 (ISO 13709-2003) Specification - Clarifications
The following is a summary of the Wood Group Surface Pump design as it relates to the requirements of
API 610, 10th Edition (ISO 13709-2003) Centrifugal Pumps for General Refinery Services.
5.0
BASIC DESIGN
5.1 General
5.1.6 Wood Group Surface Pumps are assembled with maximum diameter impellers.
A 5% head increase is possible with either a variable speed drive or selecting a
pump with blank stages.
5.1.27 Wood Group Surface Pumps can be provided with an optional discharge drop out
spool allowing the pump housing section to be removed without removing the
suction piping. Neither driver movement nor breaking discharge piping is
required to remove the pump housing.
5.1.31 Fasteners may have UNF threads and may be smaller than 12mm (0.5) diameter.
5.3 Pressure Casings
5.3.7 Pressure casings are designed per paragraph 5.3.1. Pump housings can be
provided with thicker wall dimensions where required.
5.4
Nozzles and pressure casing connections
5.4.3 Auxiliary connections
5.4.3.10
Wood Group Surface Pumps do not have standard vent or drain
connections. These connections can be provided at customer
request.
5.6
Rotors
5.6.8 Wood Group Surface Pumps standard design is 0.004 TIR or less at shaft ends
and 0.003 TIR along the shaft length.
5.6.9 Wood Group Surface Pumps have a design limit of 0.004 TIR at seal or shaft
end.
5.7
Wear rings and running clearances
5.7.1 Wood Group Surface Pumps do not include wear rings.
5.7.4 Wood Group Surface Pumps standard clearances are proven to provide
dependable service life. Clearance data is available upon request.
5.9
Dynamics
5.9.1 through 5.9.2.6
5.9.3
5.9.4
Vibration
5.9.3.6
Balancing
5.9.4.1
Wood Group and purchaser will mutually agree to the extent,
method, and acceptance criteria for these analysis. These types
of analysis are not included in our standard scope of supply but
can be offered at customer request.
Wood Group Surface Pumps limits for a fully assembled system
running on the test stand are: 0.156 in/sec RMS, unfiltered.
Impellers only are dynamically balanced to ISO 1940-1:2003
G6.3 as our standard.
API 610 Spec_Review Clarification 01-12-10
Wood Group
Surface Pumps
5.10
Bearings and Bearing Housings
5.10.2 Bearing Housings
5.10.2.10
Wood Group Surface Pumps uses a vibration map to locate and
record vibration values.
5.11
Lubrication
5.11.1 through 5.11.4. Pump inner-stage bearings are product lubricated.
5.12
Materials
5.12.1.1
Wood Group Surface Pumps standard materials of construction
are listed in the table below. Additional materials and coatings
are available when requested or specified.
COMPONENT
MATERIAL
ASTM
AISI
AMIS
Heads, Bases, etc.
Stainless Steel
316(L) Stainless
Steel
A276
Housing or Casing
Carbon Steel
C1026
A513
Optional Housing
Material
9cr-1moly
A387, A691
Pump shaft-Nitronic 50
Nitronic 50
A484
4676
Pump shaft-Inconel
Inconel 625
B446
5666
Stages-Ni-Resist
Impellers & Diffusers
Ni-Resist Type 1
A436
5392
Fasteners-Steel
Steel
Fasteners-Monel
K500
3140, 4037
4140, 5137
4677
6.0 ACCESSORIES
6.1
Drivers
6.1.10 Wood Group Surface Pumps use shimming under the skid clamps, which are
used for alignment of the pump to skid and driver.
6.3
Base plates
Wood Group Surface Pumps standard skid design does not meet all requirements set
forth in this section. All skid design modifications/requirements to be mutually agreed
upon between Wood Group and purchaser.
6.6
Special Tools
Wood Group Surface Pumps provides a list of standard mechanics tools needed to
perform maintenance work. The only special tool required is a rolling hydraulic jack
used for pump replacement.
API 610 Spec_Review Clarification 01-12-10
Wood Group
Surface Pumps
7.0 INSPECTION, TESTING, AND PREPARATION FOR SHIPMENT
7.3
Testing
7.3.1 General
7.3.1.1 Wood Group Surface Pumps conducts a performance test on each pump.
Testing is based upon API RP 11S2. Wood Group also conducts a
complete unit mechanical string test after assembly.
7.3.2 Hydrostatic Test
7.3.2.1 through 7.3.2.6 Each pump assembly is hydrostatically tested to 1.5
times MAWP.
7.3.4 Optional tests
7.3.4.1 through 7.3.4.7 Optional tests can be developed jointly by Wood Group
and the purchaser at time of order placement.
7.4
Preparation for Shipment
7.4.3.5 Wood Group Surface Pumps uses plastic or wood covers on major flange
connections as a standard.
VENDOR DATA
5.1 Proposals
5.2 Contract Data
API 610 Spec_Review Clarification 01-12-10
