Circuit Symbols
Wires and connections
Component
Circuit Symbol
Function of Component
Wire
To pass current very easily from one
part of a circuit to another.
Wires joined
A 'blob' should be drawn where wires
are connected (joined), but it is
sometimes omitted. Wires connected
at 'crossroads' should be staggered
slightly to form two T-junctions, as
shown on the right.
In complex diagrams it is often
necessary to draw wires crossing even
though they are not connected. I prefer
the 'hump' symbol shown on the right
because the simple crossing on the left
may be misread as a join where you
have forgotten to add a 'blob'!
Wires not joined
Power Supplies
Component
Circuit Symbol
Function of Component
Supplies electrical energy.
Cell
A single cell is often wrongly called a battery,
but strictly a battery is two or more cells joined
together.
Battery
Supplies electrical energy. A battery is
more than one cell.
DC supply
Supplies electrical energy.
DC = Direct Current, always flowing in
one direction.
AC supply
Supplies electrical energy.
AC = Alternating Current, continually
changing direction.
Fuse
A safety device which will 'blow' (melt) if
the current flowing through it exceeds a
specified value.
Transformer
Two coils of wire linked by an iron core.
Transformers are used to step up
(increase) and step down (decrease)
AC voltages. Energy is transferred
between the coils by the magnetic field
in the core. There is no electrical
connection between the coils.
Earth
(Ground)
A connection to earth. For many
electronic circuits this is the 0V (zero
volts) of the power supply, but for mains
electricity and some radio circuits it
really means the earth. It is also known
as ground.
Output Devices: Lamps, Heater, Motor, etc.
Component
Circuit Symbol
Function of Component
Lamp (lighting)
A transducer which converts electrical
energy to light. This symbol is used for
a lamp providing illumination, for
example a car headlamp or torch bulb.
Lamp (indicator)
A transducer which converts electrical
energy to light. This symbol is used for
a lamp which is an indicator, for
example a warning light on a car
dashboard.
Heater
A transducer which converts electrical
energy to heat.
Motor
A transducer which converts electrical
energy to kinetic energy (motion).
Bell
A transducer which converts electrical
energy to sound.
Buzzer
A transducer which converts electrical
energy to sound.
Inductor
(Coil, Solenoid)
A coil of wire which creates a magnetic
field when current passes through it. It
may have an iron core inside the coil. It
can be used as a transducer
converting electrical energy to
mechanical energy by pulling on
something.
2
Switches
Component
Circuit Symbol
Function of Component
Push Switch
(push-tomake)
A push switch allows current to flow
only when the button is pressed.
This is the switch used to operate a
doorbell.
Push-to-Break
Switch
This type of push switch is normally
closed (on), it is open (off) only when
the button is pressed.
On-Off Switch
(SPST)
SPST = Single Pole, Single Throw.
An on-off switch allows current to
flow only when it is in the closed (on)
position.
2-way Switch
(SPDT)
SPDT = Single Pole, Double Throw.
A 2-way changeover switch directs
the flow of current to one of two
routes according to its position.
Some SPDT switches have a central
off position and are described as 'onoff-on'.
Dual On-Off
Switch
(DPST)
DPST = Double Pole, Single Throw.
A dual on-off switch which is often
used to switch mains electricity
because it can isolate both the live
and neutral connections.
Reversing
Switch
(DPDT)
DPDT = Double Pole, Double Throw.
This switch can be wired up as a
reversing switch for a motor. Some
DPDT switches have a central off
position.
Relay
An electrically operated switch, for
example a 9V battery circuit
connected to the coil can switch a
230V AC mains circuit.
NO = Normally Open, COM = Common,
NC = Normally Closed.
Resistors
Component
Circuit Symbol
Function of Component
Resistor
A resistor restricts the flow of current,
for example to limit the current
passing through an LED. A resistor is
used with a capacitor in a timing
circuit.
Variable Resistor
(Rheostat)
This type of variable resistor with 2
contacts (a rheostat) is usually used
to control current. Examples include:
adjusting lamp brightness, adjusting
motor speed, and adjusting the rate of
flow of charge into a capacitor in a
timing circuit.
Variable Resistor
(Potentiometer)
This type of variable resistor with 3
contacts (a potentiometer) is usually
used to control voltage. It can be used
like this as a transducer converting
position (angle of the control spindle)
to an electrical signal.
Variable Resistor
(Preset)
This type of variable resistor (a
preset) is operated with a small
screwdriver or similar tool. It is
designed to be set when the circuit is
made and then left without further
adjustment. Presets are cheaper than
normal variable resistors so they are
often used in projects to reduce the
cost.
Capacitors
Component
Circuit Symbol
Function of Component
Capacitor
A capacitor stores electric charge. A
capacitor is used with a resistor in a
timing circuit. It can also be used as
a filter, to block DC signals but pass
AC signals.
Capacitor,
polarised
A capacitor stores electric charge.
This type must be connected the
correct way round. A capacitor is
used with a resistor in a timing
circuit. It can also be used as a filter,
to block DC signals but pass AC
signals.
Variable Capacitor
A variable capacitor is used in a
radio tuner.
Trimmer Capacitor
This type of variable capacitor (a
trimmer) is operated with a small
screwdriver or similar tool. It is
designed to be set when the circuit
is made and then left without further
adjustment.
Diodes
Component
Circuit Symbol
Function of Component
A device which only allows current
to flow in one direction.
Diode
LED
Light Emitting Diode
A transducer which converts
electrical energy to light.
Zener Diode
A special diode which is used to
maintain a fixed voltage across its
terminals.
Photodiode
A light-sensitive diode.
Transistors
Component
Circuit Symbol
Function of Component
Transistor NPN
A transistor amplifies current. It can be used
with other components to make an amplifier or
switching circuit.
Transistor PNP
A transistor amplifies current. It can be used
with other components to make an amplifier or
switching circuit.
Phototransistor
A light-sensitive transistor.
Audio and Radio Devices
Component
Circuit Symbol
Function of Component
A transducer which converts sound
to electrical energy.
Microphone
Earphone
A transducer which converts
electrical energy to sound.
Loudspeaker
A transducer which converts
electrical energy to sound.
An amplifier circuit with one input.
Really it is a block diagram symbol
because it represents a circuit rather
than just one component.
Amplifier
(general symbol)
A device which is designed to
receive or transmit radio signals. It is
also known as an antenna.
Aerial
(Antenna)
Meters and Oscilloscope
Component
Circuit Symbol
Function of Component
A voltmeter is used to measure voltage.
Voltmeter
Ammeter
Galvanometer
Ohmmeter
The proper name for voltage is 'potential
difference', but most people prefer to say
voltage!
An ammeter is used to measure
current.
A galvanometer is a very sensitive
meter which is used to measure tiny
currents, usually 1mA or less.
An ohmmeter is used to measure
resistance. Most multimeters have an
ohmmeter setting.
An oscilloscope is used to display the
shape of electrical signals and it can be
used to measure their voltage and time
period.
Oscilloscope
Sensors (input devices)
Component
Circuit Symbol
Function of Component
A transducer which converts brightness
(light) to resistance (an electrical
property).
LDR = Light Dependent Resistor
LDR
Thermistor
A transducer which converts
temperature (heat) to resistance (an
electrical property).
Logic Gates
Logic gates process signals which represent true (1, high, +Vs, on) or false (0, low,
0V, off).
There are two sets of symbols: traditional and IEC (International Electrotechnical
Commission).
Gate
Type
Traditional
Symbol
IEC Symbol
Function of Gate
NOT
A NOT gate can only have one
input. The 'o' on the output means
'not'. The output of a NOT gate is
the inverse (opposite) of its input,
so the output is true when the
input is false. A NOT gate is also
called an inverter.
AND
An AND gate can have two or
more inputs. The output of an
AND gate is true when all its
inputs are true.
NAND
A NAND gate can have two or
more inputs. The 'o' on the output
means 'not' showing that it is a
Not AND gate. The output of a
NAND gate is true unless all its
inputs are true.
OR
An OR gate can have two or more
inputs. The output of an OR gate
is true when at least one of its
inputs is true.
7
NOR
A NOR gate can have two or more
inputs. The 'o' on the output
means 'not' showing that it is a
Not OR gate. The output of a NOR
gate is true when none of its
inputs are true.
EXOR
An EX-OR gate can only have two
inputs. The output of an EX-OR
gate is true when its inputs are
different (one true, one false).
EXNOR
An EX-NOR gate can only have
two inputs. The 'o' on the output
means 'not' showing that it is a
Not EX-OR gate. The output of an
EX-NOR gate is true when its
inputs are the same (both true or
both false).
