5-Year Limited Warranty

What Does This Warranty Cover? This warranty covers any defects in workmanship or
materials in any circuit board in the PowerPulse product under normal use and service.

INSTALLATION MANUAL

PowerPulse Precautions
Make sure the correct terminal lugs are connected to the correct terminals (red on positive
and black on negative). Reversing connections could damage the PowerPulse unit.
Any solvents that may be harmful to plastic should not be used on or near the unit.

What Will PulseTech Do? PulseTech will, at its option, replace or repair any defective
circuit board with a new or rebuilt circuit board at no charge.
What Does This Warranty Not Cover? This warranty does not cover any parts other
than the circuit board. In addition, PulseTech will not be responsible under this warranty if
PulseTech determines that (1) upon examination that the circuit board failure was (A) caused
by misuse, neglect, accident, alteration, or abnormal condition of operating or handling
(including the failure to install the product in accordance with PulseTechs instructions and
observe the warnings on the product and the instruction manual), or other conditions beyond
the control of PulseTech or (B) damaged in transit to PulseTech, or (2) the owner is not the
original purchaser that purchased the product through an authorized PulseTech dealer or
distributor. IN NO EVENT SHALL PULSETECH BE LIABLE FOR ANY DIRECT, SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR EXEMPLARY DAMAGES, EXPENSES, LOST
SAVINGS OR LOST PROFITS OR ANY OTHER DAMAGES OF ANY KIND FROM ANY BREACH
OF THIS WARRANTY OR OTHERWISE. Some states, provinces or countries do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation may
not apply to you.

Secure ALL PowerPulse wires and verify they are a safe distance from moving parts before
starting the vehicle.

Warning
This product is designed for use with regularly driven vehicles or regularly charged batteries
or battery packs.
Because PowerPulse uses a minimal amount of the batterys energy in its conditioning process, external recharging may be required to replace the drain caused by internal discharge.
If used continuously on a stored vehicle over long periods of time, PowerPulse could eventually drain the power within the battery. If this occurs, the battery can still be recharged or
jumped easily and quickly. Operating the vehicle or recharging the battery can extend the
rundown time.
The pulsating current produced by the product may interfere with the correct operations of
some electronic devices when the unit is placed near the antenna. In order to insure no interference, the circuit box should be placed away from the antenna.

How Long Does the Coverage Last? This warranty runs for five (5) years from the date
of purchase.

How To Get Service? Send the product postage prepaid with proof of purchase (sales
receipt) within the warranty period to the authorized reseller where the product was purchased or contact PulseTech directly by calling 800-580-7554.
How Does State, Province or Country Law Apply? This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state, province to province
or country to country.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESSED OR IMPLIED, INCLUDING BUT NO LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

WARNING: Because of the possibility of

personal injury, always use extreme
caution when working with batteries.

PowerPulse is protected by the following

U.S. Patent Numbers: 7,834,592B2,
8,269,466B2, 8,269,465B2, 5,592,068,
5,491,399. Other U.S. and international
patents are pending.

This is just one of many battery charging

and maintenance systems manufactured by

The World Leader in Battery

Performance Technology

Congratulations, youve just purchased one of the most effective products available for ensuring lead-acid battery performance.
PowerPulse is NOT a charger. It is a proven electronic device
that helps make batteries work harder and last longer by preventing the main cause of battery problems and failure: sulfation buildup on the battery plates.
By conditioning the plates PowerPulse helps your lead-acid
batteries work harder and last longer than ever before.
Installing PowerPulse is very easy, just follow the simple
instructions inside.

1100 South Kimball Avenue

Southlake, Texas 76092
Phone 800-580-7554 FAX 817-329-5914
Email [email protected]

www.pulsetech.net
2010 PulseTech Products Corporation. All rights reserved. No portion may be reproduced
without written permission.
998XM011 1/13

The World Leader in Battery

Performance Technology

Mount The Circuit Box

1

For 12-volt batteries we suggest you mount the circuit box near

etc. The circuit box can be mounted in one of two ways:

in the set (see Fig. 2 for an example of how a 12-Volt PowerPulse is

plates. (see Fig. 1.)

installed on two (2) 6-volt batteries and Fig. 4 for a 36-volt PowerPulse

Repeat steps 1 & 2 for the negative wire.

on six (6) 6-volt batteries).

LED

Two 6-Volt Batteries In Series

head screws to attach the circuit box to the surface of the

Each PowerPulse unit has an LED on top of the circuit box. When

connected in series (creating

vehicle or equipment in an area away from moving engine

properly installed the LED will blink when the wires are attached to the

12-volts), follow steps 1 above.

parts.

On step 2 connect the positive

2nd Method: Apply an industrial adhesive to the back of the

wire to the positive terminal on Battery 1 and the negative wire to the

circuit box and affix it to the surface of the vehicle or equip-

negative terminal on Battery 2 (see Fig. 2).

1. The PowerPulse has been installed incorrectly (reversed polarity).

Batteries In Parallel

2. There is a bad connection.

Once the circuit box has been mounted, use plastic cable ties to
This will keep the wires from tangling with moving engine parts.

Connect Lugs To Battery Terminals

IMPORTANT: The positive (+) PowerPulse wire (red) must be connected to the positive (+) battery terminal and the negative ()
PowerPulse wire (black) to the negative () battery terminal in order
for PowerPulse to work.
12-Volt PowerPulse:
Single 12-volt batteries

tery and the negative wire to the negative terminal on the last battery

For two (2) 6-volt batteries

secure the wires to a cable or other secure area near the battery.

Fig. 1

1st Method: For a semi-permanent installation, use two round

ment.

2 connect the positive wire to the positive terminal on the first bat-

the buildup of sulfates on the lead

batteries for forklifts, pallet jacks, etc., mounting the unit on the
protected and will not accidentally be disturbed by mechanics,

To install, follow step 1 under the 12-Volt PowerPulse section. On step

current through the terminal and

into the battery which will eliminate

the battery and not on the battery itself. However, on large motive
battery is fine. Make sure it is situated in a location where it is

PowerPulse to send a pulsating

Fig. 2

For 12-volt batteries

PowerPulse on the bat-

the LED does not light it may be due to one of the following reasons:

3. The battery voltage is too low to operate the PowerPulse, charge the

connected in parallel
install one (1) 12-Volt

battery terminals and the unit is activated. Once the unit is installed, if

battery then re-check.

Fig. 3

Basic Care and Cleaning

tery pack. Connect either to the positive and negative of one battery

The PowerPulse system is completely weatherproof so normal mois-

or the positive of the first battery and the negative of the last battery.

ture will not damage it. If the circuit box gets dusty or dirty, simply

12V PowerPulse is most efficient in parallel connected battery packs

clean it with a damp cloth. DO NOT use cleaning solvents.

using a maximum of 3 batteries (see Fig. 3).

Call For More Information

24, 36 and 48-Volt

For more information on installing and using PowerPulse or our other

Installations:

PulseTech battery maintenance products, contact your local PulseTech

For 6- or 12-volt bat-

dealer. For technical assistance or the name of the dealer nearest you

Slip the round metal lug at the end of the positive (red)

teries connected in

PowerPulse terminal wire onto the bolt securing the battery

series to equal 24, 36

clamp to the positive terminal until it sits next to the nut tighten-

or 48 volts, use the PowerPulse unit designed

ing the clamp.

for each specific voltage; 12,-, 24-, 36- or 48-volt products.

Screw a hex nut onto the bolt and tighten it until it secures the

Installation of multiple 12V PowerPulse units on each 12V battery seg-

lug and washer between it and the clamp nut. This will allow

ment in 24V, 36V or 48V packs will yield 30% better results.

call us at 800-580-7554. Or visit our site at www.pulsetech.net.

Fig. 4

998XM011 1/13