Chapter 13, Solution 1.

For coil 1, L1 – M12 + M13 = 6 – 4 + 2 = 4

For coil 2, L2 – M21 – M23 = 8 – 4 – 5 = – 1

For coil 3, L3 + M31 – M32 = 10 + 2 – 5 = 7

LT = 4 – 1 + 7 = 10H

or LT = L1 + L2 + L3 – 2M12 – 2M23 + 2M12

LT = 6 + 8 + 10 = 10H

Chapter 13, Solution 2.

L = L1 + L2 + L3 + 2M12 – 2M23 2M31

= 10 + 12 +8 + 2x6 – 2x6 –2x4

= 22H

Chapter 13, Solution 3.

L1 + L2 + 2M = 250 mH (1)

L1 + L2 – 2M = 150 mH (2)

Adding (1) and (2),

2L1 + 2L2 = 400 mH

But, L1 = 3L2,, or 8L2 + 400, and L2 = 50 mH

L1 = 3L2 = 150 mH

From (2), 150 + 50 – 2M = 150 leads to M = 25 mH

k = M/ L1 L 2 = 2.5 / 50x150 = 0.2887

Chapter 13, Solution 4.

(a) For the series connection shown in Figure (a), the current I enters each coil from
its dotted terminal. Therefore, the mutually induced voltages have the same sign as the
self-induced voltages. Thus,
Leq = L1 + L2 + 2M

Is
L1
I1 I2
+
Vs –
L2
L1 L2

Leq
(a)
(b)
(b) For the parallel coil, consider Figure (b).

Is = I 1 + I2 and Zeq = Vs/Is

Applying KVL to each branch gives,

Vs = jωL1I1 + jωMI2 (1)

Vs = jωMI1 + jω L2I2 (2)

 Vs   jωL1 jωM   I1 
or  V  =  jωM jωL 2  I 2 
 s 

∆ = –ω2L1L2 + ω2M2, ∆1 = jωVs(L2 – M), ∆2 = jωVs(L1 – M)

I1 = ∆1/∆, and I2 = ∆2/∆

Is = I1 + I2 = (∆1 + ∆2)/∆ = jω(L1 + L2 – 2M)Vs/( –ω2(L1L2 – M))

Zeq = Vs/Is = jω(L1L2 – M)/[jω(L1 + L2 – 2M)] = jωLeq

i.e., Leq = (L1L2 – M)/(L1 + L2 – 2M)

Chapter 13, Solution 5.

(a) If the coils are connected in series,

L = L1 + L 2 + 2M = 25 + 60 + 2(0.5) 25x 60 = 123.7 mH

(b) If they are connected in parallel,

L1 L 2 − M 2 25x 60 − 19.36 2
L= = mH = 24.31 mH
L1 + L 2 − 2M 25 + 60 − 2x19.36

Chapter 13, Solution 6.

V1 = (R1 + jωL1)I1 – jωMI2

V2 = –jωMI1 + (R2 + jωL2)I2

Chapter 13, Solution 7.

Applying KVL to the loop,

20∠30° = I(–j6 + j8 + j12 + 10 – j4x2) = I(10 + j6)

where I is the loop current.

I = 20∠30°/(10 + j6)

Vo = I(j12 + 10 – j4) = I(10 + j8)

= 20∠30°(10 + j8)/(10 + j6) = 22∠37.66° V

Chapter 13, Solution 8.

Consider the current as shown below.

j2
1Ω 4Ω

+ +
10 –
I1 j6 j4 I2 -j3 Vo
–
 For mesh 1,

10 = (1 + j6)I1 + j2I2 (1)

For mesh 2, 0 = (4 + j4 – j3)I2 + j2I1

0 = j2I1 +(4 + j)I2 (2)

In matrix form,

10 1 + j6 j2   I1 
 0  =  j2 4+ j  I 2 
  

∆ = 2 + j25, and ∆2 = –j20

I2 = ∆2/∆ = –j20/(2 + j25)

Vo = –j3I2 = –60/(2 + j25) = 2.392∠94.57°

Chapter 13, Solution 9.

Consider the circuit below.

2Ω 2Ω -j1

+
8∠30o – j4
+
I1 j4 I2 -j2V –

For loop 1,

8∠30° = (2 + j4)I1 – jI2 (1)

For loop 2, ((j4 + 2 – j)I2 – jI1 + (–j2) = 0

or I1 = (3 – j2)i2 – 2 (2)

Substituting (2) into (1), 8∠30° + (2 + j4)2 = (14 + j7)I2

I2 = (10.928 + j12)/(14 + j7) = 1.037∠21.12°

Vx = 2I2 = 2.074∠21.12°
Chapter 13, Solution 10.

Consider the circuit below.

jωM

jωL jωL

Io

I1 I2
Iin∠0o
1/jωC

M = k L1 L 2 = L2 = L, I1 = Iin∠0°, I2 = Io
Io(jωL + R + 1/(jωC)) – jωLIin – (1/(jωC))Iin = 0
Io = j Iin(ωL – 1/(ωC)) /(R + jωL + 1/(jωC))

Chapter 13, Solution 11.

Consider the circuit below.

R2 V2
+–

I3
R1 jωL1

jωM
1/jωC
V1
+ I1 jωL2
–
I2

For mesh 1, V1 = I1(R1 + 1/(jωC)) – I2(1/jωC)) –R1I3

For mesh 2,
0 = –I1(1/(jωC)) + (jωL1 + jωL2 + (1/(jωC)) – j2ωM)I2 – jωL1I3 + jωMI3

For mesh 3, –V2 = –R1I1 – jω(L1 – M)I2 + (R1 + R2 + jωL1)I3

or V2 = R1I1 + jω(L1 – M)I2 – (R1 + R2 + jωL1)I3

Chapter 13, Solution 12.

Let ω = 1. j4
j2

•
+ j6 j8 j10
1V
- I1 I2
•

Applying KVL to the loops,

1 = j8 I 1 + j 4 I 2 (1)
0 = j 4 I 1 + j18 I 2 (2)
Solving (1) and (2) gives I1 = -j0.1406. Thus

1 1
Z= = jLeq 
→ Leq = = 7.111 H
I1 jI 1

We can also use the equivalent T-section for the transform to find the equivalent
inductance.

Chapter 13, Solution 13.

We replace the coupled inductance with an equivalent T-section and use series and
parallel combinations to calculate Z. Assuming that ω = 1,

La = L1 − M = 18 − 10 = 8, Lb = L2 − M = 20 − 10 = 10, Lc = M = 10
The equivalent circuit is shown below:
 12 Ω j8 Ω j10 Ω 2Ω

j10 Ω

-j6 Ω
Z

j4 Ω

Z=12 +j8 + j14//(2 + j4) = 13.195 + j11.244Ω

Chapter 13, Solution 14.

To obtain VTh, convert the current source to a voltage source as shown below.

j2

5Ω j6 Ω j8 Ω -j3 Ω 2Ω

a
+ I +
+ 8V –
j10 V – VTh
–
b

Note that the two coils are connected series aiding.

ωL = ωL1 + ωL2 – 2ωM

jωL = j6 + j8 – j4 = j10

Thus, –j10 + (5 + j10 – j3 + 2)I + 8 = 0

I = (– 8 + j10)/ (7 + j7)

But, –j10 + (5 + j6)I – j2I + VTh = 0

 VTh = j10 – (5 + j4)I = j10 – (5 + j4)(–8 + j10)/(7 + j7)

VTh = 5.349∠34.11°

To obtain ZTh, we set all the sources to zero and insert a 1-A current source at the terminals
a–b as shown below.

j2

5Ω j6 Ω j8 Ω -j3 Ω 2Ω
a

+
I1 1A Vo I2
–

Clearly, we now have only a super mesh to analyze.

(5 + j6)I1 – j2I2 + (2 + j8 – j3)I2 – j2I1 = 0

(5 + j4)I1 + (2 + j3)I2 = 0 (1)

But, I2 – I1 = 1 or I2 = I1 – 1 (2)

Substituting (2) into (1), (5 + j4)I1 +(2 + j3)(1 + I1) = 0

I1 = –(2 + j3)/(7 + j7)

Now, ((5 + j6)I1 – j2I1 + Vo = 0

Vo = –(5 + j4)I1 = (5 + j4)(2 + j3)/(7 + j7) = (–2 + j23)/(7 + j7) = 2.332∠50°

ZTh = Vo/1 = 2.332∠50° ohms

Chapter 13, Solution 15.

To obtain IN, short-circuit a–b as shown in Figure (a).

20 Ω j20 Ω 20 Ω j20 Ω
a a

j5 j5
I1 j10 Ω 1
+ j10 Ω +
– IN –
60∠30o I1 I2
I2

b b
(a) (b)
For mesh 1,
60∠30° = (20 + j10)I1 + j5I2 – j10I2

or 12∠30° = (4 + j2)I1 – jI2 (1)

For mesh 2,
0 = (j20 + j10)I2 – j5I1 – j10I1

or I1 = 2I2 (2)

Substituting (2) into (1), 12∠30° = (8 + j3)I2

IN = I2 = 12∠30°/(8 + j3) = 1.404∠9.44° A

To find ZN, we set all the sources to zero and insert a 1-volt voltage source at terminals a–
b as shown in Figure (b).

For mesh 1, 1 = I1(j10 + j20 – j5x2) + j5I2

1 = j20I1 + j5I2 (3)

For mesh 2, 0 = (20 + j10)I2 + j5I1 – j10I1 = (4 + j2)I2 – jI1

or I2 = jI1/(4 + j2) (4)

Substituting (4) into (3), 1 = j20I1 + j(j5)I1/(4 + j2) = (–1 + j20.5)I1

I1 = 1/(–1 + j20.5)

ZN = 1/I1 = (–1 + j20.5) ohms

Chapter 13, Solution 16.

To find IN, we short-circuit a-b.

jΩ
8Ω -j2 Ω

a
• •

+ j4 Ω j6 Ω I2 IN
80∠0 V o
I1
-
b

− 80 + (8 − j 2 + j 4) I 1 − jI 2 = 0 → (8 + j 2) I 1 − jI 2 = 80 (1)
j 6 I 2 − jI 1 = 0 
→ I1 = 6I 2 (2)

Solving (1) and (2) leads to

80
IN = I2 = = 1.584 − j 0.362 = 1.6246∠ − 12.91o A
48 + j11

To find ZN, insert a 1-A current source at terminals a-b. Transforming the current source
to voltage source gives the circuit below.

jΩ
8Ω -j2 Ω 2Ω
a

• • +

j4 Ω j6 Ω I2 2V
I1
-
b

jI 2
0 = (8 + j 2) I 1 − jI 2 
→ I1 = (3)
8 + j2

2 + (2 + j 6) I 2 − jI 1 = 0 (4)
Solving (3) and (4) leads to I2 = -0.1055 +j0.2975, Vab=-j6I2 = 1.7853 +0.6332

Vab
ZN = = 1.894∠19.53o Ω
1
Chapter 13, Solution 17.

Z = -j6 // Zo
where
144
Z o = j20 + = 0.5213 + j15.7
j30 − j2 + j5 + 4

− j6 xZ o
Z= = 0.1989 − j9.7Ω
− j6 + Z o

Chapter 13, Solution 18.

Let ω = 1. L1 = 5, L2 = 20, M = k L1 L2 = 0.5 x10 = 5

We replace the transformer by its equivalent T-section.

La = L1 − (− M ) = 5 + 5 = 10, Lb = L1 + M = 20 + 5 = 25, Lc = − M = −5

We find ZTh using the circuit below.

-j4 j10 j25 j2

-j5

ZTh

4+j6

j 6(4 + j )
Z Th = j 27 + (4 + j ) //( j 6) = j 27 + = 2.215 + j 29.12Ω
4 + j7

We find VTh by looking at the circuit below.

 -j4 j10 j25 j2

+
-j5
+
VTh
o
120<0
4+j6 -
-

4+ j
VTh = (120) = 61.37∠ − 46.22 o V
4 + j + j6

Chapter 13, Solution 19.

Let ω = 1. La = L1 − (− M ) = 40 + 25 = 65 H

Lb = L2 + M = 30 + 25 = 55 H, L C = − M = −25

Thus, the T-section is as shown below.

j65 Ω j55 Ω

-j25 Ω
Chapter 13, Solution 20.

Transform the current source to a voltage source as shown below.

k=0.5

4Ω j10 j10 8Ω

I3
+
– j12 I1 -j5 I2 +
20∠0o –

k = M/ L1 L 2 or M = k L1 L 2

ωM = k ωL1ωL 2 = 0.5(10) = 5

For mesh 1, j12 = (4 + j10 – j5)I1 + j5I2 + j5I2 = (4 + j5)I1 + j10I2 (1)

For mesh 2, 0 = 20 + (8 + j10 – j5)I2 + j5I1 + j5I1

–20 = +j10I1 + (8 + j5)I2 (2)

 j12 4 + j5 + j10   I1 
From (1) and (2),  20  =  + j10 8 + j5 I 
    2 

∆ = 107 + j60, ∆1 = –60 –j296, ∆2 = 40 – j100

I1 = ∆1/∆ = 2.462∠72.18° A

I2 = ∆2/∆ = 0.878∠–97.48° A

I3 = I1 – I2 = 3.329∠74.89° A

i1 = 2.462 cos(1000t + 72.18°) A

i2 = 0.878 cos(1000t – 97.48°) A

At t = 2 ms, 1000t = 2 rad = 114.6°

i1 = 0.9736cos(114.6° + 143.09°) = –2.445

i2 = 2.53cos(114.6° + 153.61°) = –0.8391

The total energy stored in the coupled coils is

w = 0.5L1i12 + 0.5L2i22 – Mi1i2

Since ωL1 = 10 and ω = 1000, L1 = L2 = 10 mH, M = 0.5L1 = 5mH

w = 0.5(10)(–2.445)2 + 0.5(10)(–0.8391)2 – 5(–2.445)(–0.8391)

w = 43.67 mJ

Chapter 13, Solution 21.

For mesh 1, 36∠30° = (7 + j6)I1 – (2 + j)I2 (1)

For mesh 2, 0 = (6 + j3 – j4)I2 – 2I1 jI1 = –(2 + j)I1 + (6 – j)I2 (2)

36∠30°  7 + j6 − 2 − j  I1 
Placing (1) and (2) into matrix form,  0  = − 2 − j 6 − j  I 
    2 

∆ = 48 + j35 = 59.41∠36.1°, ∆1 = (6 – j)36∠30° = 219∠20.54°

∆2 = (2 + j)36∠30° = 80.5∠56.56°, I1 = ∆1/∆ = 3.69∠–15.56°, I2 = ∆2/∆ = 1.355∠20.46°

Power absorbed fy the 4-ohm resistor, = 0.5(I2)24 = 2(1.355)2 = 3.672 watts

Chapter 13, Solution 22.

With more complex mutually coupled circuits, it may be easier to show the effects of the
coupling as sources in terms of currents that enter or leave the dot side of the coil. Figure
13.85 then becomes,
-j50
Io
I3
j20Ic j10Ib j60
j40
+ − + − − + − +
Ia Ix
− j30Ib j20Ia
j30Ic +
50∠0° V
+ j80 100 Ω
− I1 I2
Ib
−
+ j10Ia

Note the following,

Ia = I 1 – I3
Ib = I2 – I1
Ic = I 3 – I2

and Io = I 3

Now all we need to do is to write the mesh equations and to solve for Io.

Loop # 1,

-50 + j20(I3 – I2) j 40(I1 – I3) + j10(I2 – I1) – j30(I3 – I2) + j80(I1 – I2) – j10(I1 – I3) = 0

j100I1 – j60I2 – j40I3 = 50

Multiplying everything by (1/j10) yields 10I1 – 6I2 – 4I3 = - j5 (1)

Loop # 2,

j10(I1 – I3) + j80(I2–I1) + j30(I3–I2) – j30(I2 – I1) + j60(I2 – I3) – j20(I1 – I3) + 100I2 = 0

-j60I1 + (100 + j80)I2 – j20I3 = 0 (2)

Loop # 3,

-j50I3 +j20(I1 –I3) +j60(I3 –I2) +j30(I2 –I1) –j10(I2 –I1) +j40(I3 –I1) –j20(I3 –I2) = 0

-j40I1 – j20I2 + j10I3 = 0

Multiplying by (1/j10) yields, -4I1 – 2I2 + I3 = 0 (3)

Multiplying (2) by (1/j20) yields -3I1 + (4 – j5)I2 – I3 = 0 (4)

Multiplying (3) by (1/4) yields -I1 – 0.5I2 – 0.25I3 = 0 (5)

Multiplying (4) by (-1/3) yields I1 – ((4/3) – j(5/3))I2 + (1/3)I3 = -j0.5 (7)

Multiplying [(6)+(5)] by 12 yields (-22 + j20)I2 + 7I3 = 0 (8)

Multiplying [(5)+(7)] by 20 yields -22I2 – 3I3 = -j10 (9)

(8) leads to I2 = -7I3/(-22 + j20) = 0.2355∠42.3o = (0.17418+j0.15849)I3 (10)

(9) leads to I3 = (j10 – 22I2)/3, substituting (1) into this equation produces,

I3 = j3.333 + (-1.2273 – j1.1623)I3

or I3 = Io = 1.3040∠63o amp.

Chapter 13, Solution 23.

ω = 10

0.5 H converts to jωL1 = j5 ohms

1 H converts to jωL2 = j10 ohms

0.2 H converts to jωM = j2 ohms

25 mF converts to 1/(jωC) = 1/(10x25x10-3) = –j4 ohms

The frequency-domain equivalent circuit is shown below.

j2
j5 j10

+ I1 –j4 I2
12∠0° −
5Ω
For mesh 1, 12 = (j5 – j4)I1 + j2I2 – (–j4)I2

–j2 = I1 + 6I2 (1)

For mesh 2, 0 = (5 + j10)I2 + j2I1 –(–j4)I1

0 = (5 + j10)I2 + j6I1 (2)

From (1), I1 = –j12 – 6I2

Substituting this into (2) produces,

I2 = 72/(–5 + j26) = 2.7194∠–100.89°

I1 = –j12 – 6 I2 = –j12 – 163.17∠–100.89 = 5.068∠52.54°

Hence, i1 = 5.068cos(10t + 52.54°) A, i2 = 2.719cos(10t – 100.89°) A.

At t = 15 ms, 10t = 10x15x10-3 0.15 rad = 8.59°

i1 = 5.068cos(61.13°) = 2.446

i2 = 2.719cos(–92.3°) = –0.1089

w = 0.5(5)(2.446)2 + 0.5(1)(–0.1089)2 – (0.2)(2.446)(–0.1089) = 15.02 J

Chapter 13, Solution 24.

(a) k = M/ L1 L 2 = 1/ 4 x 2 = 0.3535

(b) ω = 4

1/4 F leads to 1/(jωC) = –j/(4x0.25) = –j

1||(–j) = –j/(1 – j) = 0.5(1 – j)

1 H produces jωM = j4

4 H produces j16

2 H becomes j8
 j4
2Ω

j8
+ I1 I2 0.5(1–j)
12∠0° −
j16

12 = (2 + j16)I1 + j4I2

or 6 = (1 + j8)I1 + j2I2 (1)

0 = (j8 + 0.5 – j0.5)I2 + j4I1 or I1 = (0.5 + j7.5)I2/(–j4) (2)

Substituting (2) into (1),

24 = (–11.5 – j51.5)I2 or I2 = –24/(11.5 + j51.5) = –0.455∠–77.41°

Vo = I2(0.5)(1 – j) = 0.3217∠57.59°

vo = 321.7cos(4t + 57.6°) mV

(c) From (2), I1 = (0.5 + j7.5)I2/(–j4) = 0.855∠–81.21°

i1 = 0.885cos(4t – 81.21°) A, i2 = –0.455cos(4t – 77.41°) A

At t = 2s,
4t = 8 rad = 98.37°

i1 = 0.885cos(98.37° – 81.21°) = 0.8169

i2 = –0.455cos(98.37° – 77.41°) = –0.4249

w = 0.5L1i12 + 0.5L2i22 + Mi1i2

= 0.5(4)(0.8169)2 + 0.5(2)(–.4249)2 + (1)(0.1869)(–0.4249) = 1.168 J

Chapter 13, Solution 25.

m = k L1 L 2 = 0.5 H

We transform the circuit to frequency domain as shown below.

12sin2t converts to 12∠0°, ω = 2

0.5 F converts to 1/(jωC) = –j

2 H becomes jωL = j4
j1
Io 4 Ω a 1Ω 2Ω

–j1

+ j2 j2
12∠0° − j4

10 Ω

b
Applying the concept of reflected impedance,

Zab = (2 – j)||(1 + j2 + (1)2/(j2 + 3 + j4))

= (2 – j)||(1 + j2 + (3/45) – j6/45)

= (2 – j)||(1 + j2 + (3/45) – j6/45)

= (2 – j)||(1.0667 + j1.8667)

=(2 – j)(1.0667 + j1.8667)/(3.0667 + j0.8667) = 1.5085∠17.9° ohms

Io = 12∠0°/(Zab + 4) = 12/(5.4355 + j0.4636) = 2.2∠–4.88°

io = 2.2sin(2t – 4.88°) A
Chapter 13, Solution 26.

M = k L1L 2

ωM = k ωL1ωL 2 = 0.6 20x 40 = 17

The frequency-domain equivalent circuit is shown below.

j17
50 Ω –j30
Io

+ I1 j20 j40
200∠60° I2 10 Ω
−

For mesh 1,
200∠60° = (50 – j30 + j20)I1 + j17I2 = (50 – j10)I1 + j17I2 (1)

For mesh 2,
0 = (10 + j40)I2 + j17I1 (2)

200∠60° 50 − j10 j17   I1 

In matrix form, =

 0 
  j17 10 + j40 I 2 

∆ = 900 + j100, ∆1 = 2000∠60°(1 + j4) = 8246.2∠136°, ∆2 = 3400∠–30°

I2 = ∆2/∆ = 3.755∠–36.34°

Io = I2 = 3.755∠–36.34° A

Switching the dot on the winding on the right only reverses the direction of Io.
This can be seen by looking at the resulting value of ∆2 which now becomes
3400∠150°. Thus,

Io = 3.755∠143.66° A
Chapter 13, Solution 27.

Zin = –j4 + j5 + 9/(12 + j6) = 0.6 + j.07 = 0.922∠49.4°

I1 = 12∠0°/0.922∠49.4° = 13∠–49.4° A

Chapter 13, Solution 28.

We find ZTh by replacing the 20-ohm load with a unit source as shown below.

j10 Ω
8Ω -jX

• •
+
j12 Ω j15 Ω I2 1V
-
I1

For mesh 1, 0 = (8 − jX + j12) I 1 − j10 I 2 (1)

For mesh 2, 1 + j15I 2 − j10 I 1 = 0 

→ I 1 = 1.5I 2 − 0.1 j (2)

Substituting (2) into (1) leads to

− 1.2 + j 0.8 + 0.1X
I2 =
12 + j8 − j1.5 X

1 12 + j8 − j1.5 X
Z Th = =
− I 2 1.2 − j 0.8 − 0.1X

12 2 + (8 − 1.5 X ) 2
| Z Th |= 20 = 
→ 0 = 1.75 X 2 + 72 X − 624
(1.2 − 0.1X ) + 0.8
2 2

Solving the quadratic equation yields X = 6.425

Chapter 13, Solution 29.

30 mH becomes jωL = j30x10-3x103 = j30

50 mH becomes j50

Let X = ωM

Using the concept of reflected impedance,

Zin = 10 + j30 + X2/(20 + j50)

I1 = V/Zin = 165/(10 + j30 + X2/(20 + j50))

p = 0.5|I1|2(10) = 320 leads to |I1|2 = 64 or |I1| = 8

8 = |165(20 + j50)/(X2 + (10 + j30)(20 + j50))|

= |165(20 + j50)/(X2 – 1300 + j1100)|

or 64 = 27225(400 + 2500)/((X2 – 1300)2 + 1,210,000)

(X2 – 1300)2 + 1,210,000 = 1,233,633

X = 33.86 or 38.13

If X = 38.127 = ωM

M = 38.127 mH

k = M/ L1 L 2 = 38.127/ 30x50 = 0.984

j38.127
10 Ω

+ I1 j30 j50
165∠0° I2 20 Ω
−
 165 = (10 + j30)I1 – j38.127I2 (1)

0 = (20 + j50)I2 – j38.127I1 (2)

165  10 + j30 − j38.127  I1 
In matrix form,  0  =  − j38.127 20 + j50   I 
    2 

∆ = 154 + j1100 = 1110.73∠82.03°, ∆1 = 888.5∠68.2°, ∆2 = j6291

I1 = ∆1/∆ = 8∠–13.81°, I2 = ∆2/∆ = 5.664∠7.97°

i1 = 8cos(1000t – 13.83°), i2 = 5.664cos(1000t + 7.97°)

At t = 1.5 ms, 1000t = 1.5 rad = 85.94°

i1 = 8cos(85.94° – 13.83°) = 2.457

i2 = 5.664cos(85.94° + 7.97°) = –0.3862

w = 0.5L1i12 + 0.5L2i22 + Mi1i2

= 0.5(30)(2.547)2 + 0.5(50)(–0.3862)2 – 38.127(2.547)(–0.3862)

= 130.51 mJ

Chapter 13, Solution 30.

(a) Zin = j40 + 25 + j30 + (10)2/(8 + j20 – j6)

= 25 + j70 + 100/(8 + j14) = (28.08 + j64.62) ohms

(b) jωLa = j30 – j10 = j20, jωLb = j20 – j10 = j10, jωLc = j10

Thus the Thevenin Equivalent of the linear transformer is shown below.

j40 25 Ω j20 j10 8Ω

–j6
j10

Zin
Zin = j40 + 25 + j20 + j10||(8 + j4) = 25 + j60 + j10(8 + j4)/(8 + j14)

= (28.08 + j64.62) ohms

Chapter 13, Solution 31.

(a) La = L1 – M = 10 H

Lb = L2 – M = 15 H

Lc = M = 5 H

(b) L1L2 – M2 = 300 – 25 = 275

LA = (L1L2 – M2)/(L1 – M) = 275/15 = 18.33 H

LB = (L1L2 – M2)/(L1 – M) = 275/10 = 27.5 H

LC = (L1L2 – M2)/M = 275/5 = 55 H

Chapter 13, Solution 32.

We first find Zin for the second stage using the concept of reflected impedance.

Lb LB R

Zin’
Zin’ = jωLb + ω2Mb2/(R + jωLb) = (jωLbR - ω2Lb2 + ω2Mb2)/(R + jωLb) (1)

For the first stage, we have the circuit below.

La LA Zin’

Zin

Zin = jωLa + ω2Ma2/(jωLa + Zin)

= (–ω2La2 + ω2Ma2 + jωLaZin)/( jωLa + Zin) (2)

Substituting (1) into (2) gives,

( jωL b R − ω 2 L2b + ω 2 M 2b )
− ω L + ω M + jωL a
2 2
a
2 2
a
R + jω L b
=
jωL b R − ω L b + ω 2 M 2b
2 2
jωL a +
R + jω L b

–Rω2La2 + ω2Ma2R – jω3LbLa + jω3LbMa2 + jωLa(jωLbR – ω2Lb2 + ω2Mb2)

=
jωRLa –ω2LaLb + jωLbR – ω2La2 + ω2Mb2

ω2R(La2 + LaLb – Ma2) + jω3(La2Lb + LaLb2 – LaMb2 – LbMa2)

Zin =
ω2(LaLb +Lb2 – Mb2) – jωR(La +Lb)

Chapter 13, Solution 33.

Zin = 10 + j12 + (15)2/(20 + j 40 – j5) = 10 + j12 + 225/(20 + j35)

= 10 + j12 + 225(20 – j35)/(400 + 1225)

= (12.769 + j7.154) ohms

Chapter 13, Solution 34.

Insert a 1-V voltage source at the input as shown below.

j6 Ω
1Ω 8Ω

• •
+
j12 Ω j10 Ω j4 Ω
o
1<0 V I1 I2
-

-j2 Ω
For loop 1,
1 = (1 + j10) I 1 − j 4 I 2 (1)
For loop 2,

0 = (8 + j 4 + j10 − j 2) I 2 + j 2 I 1 − j 6 I 1 
→ 0 = − jI 1 + (2 + j 3) I 2 (2)

Solving (1) and (2) leads to I1=0.019 –j0.1068

1
Z= = 1.6154 + j 9.077 = 9.219∠79.91o Ω
I1

Alternatively, an easier way to obtain Z is to replace the transformer with its equivalent
T circuit and use series/parallel impedance combinations. This leads to exactly the same
result.

Chapter 13, Solution 35.

For mesh 1, 16 = (10 + j 4) I 1 + j 2 I 2 (1)

For mesh 2, 0 = j 2 I 1 + (30 + j 26) I 2 − j12 I 3 (2)

For mesh 3, 0 = − j12 I 2 + (5 + j11) I 3 (3)

We may use MATLAB to solve (1) to (3) and obtain

I 1 = 1.3736 − j 0.5385 = 1.4754∠ − 21.41o A

I 2 = −0.0547 − j 0.0549 = 0.0775∠ − 134.85 o A
I 3 = −0.0268 − j 0.0721 = 0.077∠ − 110.41o A

Chapter 13, Solution 36.

Following the two rules in section 13.5, we obtain the following:

(a) V2/V1 = –n, I2/I1 = –1/n (n = V2/V1)

(b) V2/V1 = –n, I2/I1 = –1/n

(c) V2/V1 = n, I2/I1 = 1/n

(d) V2/V1 = n, I2/I1 = –1/n

Chapter 13, Solution 37.

V2 2400
(a) n = = =5
V1 480

50,000
(b) S1 = I 1V1 = S 2 = I 2V2 = 50,000 
→ I1 = = 104.17 A
480

50,000
(c ) I 2 = = 20.83 A
2400

Chapter 13, Solution 38.

Zin = Zp + ZL/n2, n = v2/v1 = 230/2300 = 0.1

v2 = 230 V, s2 = v2I2*

I2* = s2/v2 = 17.391∠–53.13° or I2 = 17.391∠53.13° A

ZL = v2/I2 = 230∠0°/17.391∠53.13° = 13.235∠–53.13°

Zin = 2∠10° + 1323.5∠–53.13°

= 1.97 + j0.3473 + 794.1 – j1058.8

Zin = 1.324∠–53.05° kohms

Chapter 13, Solution 39.

Referred to the high-voltage side,

ZL = (1200/240)2(0.8∠10°) = 20∠10°

Zin = 60∠–30° + 20∠10° = 76.4122∠–20.31°

I1 = 1200/Zin = 1200/76.4122∠–20.31° = 15.7∠20.31° A

Since S = I1v1 = I2v2, I2 = I1v1/v2

= (1200/240)( 15.7∠20.31°) = 78.5∠20.31° A

Chapter 13, Solution 40.

N2 500 1 V2 1
n= = = , n= → V2 = nV1 = (240) = 60 V
N1 2000 4 V1 4

V 2 60 2
P= = = 300 W
R 12

Chapter 13, Solution 41.

We reflect the 2-ohm resistor to the primary side.

Zin = 10 + 2/n2, n = –1/3

Since both I1 and I2 enter the dotted terminals, Zin = 10 + 18 = 28 ohms

I1 = 14∠0°/28 = 0.5 A and I2 = I1/n = 0.5/(–1/3) = –1.5 A

Chapter 13, Solution 42.

10 Ω 1:4 -j50 Ω

+ • • + +
+ V1 V2
20 Ω Vo
120<0o V I1 - -
- -
I2

Applying mesh analysis,

120 = 10I1 + V1 (1)

0 = (20 − j50)I 2 + V2 (2)

 At the terminals of the transformer,

V2
=n=4 → V2 = 4V1 (3)
V1

I2 1 1
=− =− 
→ I1 = −4I 2 (4)
I1 n 4

Substituting (3) and (4) into (1) gives 120 = −40I 2 + 0.25V2 (5)

Solving (2) and (5) yields I 2 = −2.4756 − j0.6877

Vo = −20I 2 = 51.39∠15.52 o V

Chapter 13, Solution 43.

Transform the two current sources to voltage sources, as shown below.

10 Ω 12 Ω
1:4
+ +
+
20 V – v1 v2 +
I1 I2 12V –
− −

Using mesh analysis, –20 + 10I1 + v1 = 0

20 = v1 + 10I1 (1)

12 + 12I2 – v2 = 0 or 12 = v2 – 12I2 (2)

At the transformer terminal, v2 = nv1 = 4v1 (3)

I1 = nI2 = 4I2 (4)

Substituting (3) and (4) into (1) and (2), we get,

20 = v1 + 40I2 (5)

12 = 4v1 – 12I2 (6)

Solving (5) and (6) gives v1 = 4.186 V and v2 = 4v = 16.744 V

Chapter 13, Solution 44.

We can apply the superposition theorem. Let i1 = i1’ + i1” and i2 = i2’ + i2”
where the single prime is due to the DC source and the double prime is due to the
AC source. Since we are looking for the steady-state values of i1 and i2,

i1’ = i2’ = 0.

For the AC source, consider the circuit below.

R
1:n
+ +
v1 v2 +
i1” i2” – Vn∠0°
− −

v2/v1 = –n, I2”/I1” = –1/n

But v2 = vm, v1 = –vm/n or I1” = vm/(Rn)

I2” = –I1”/n = –vm/(Rn2)

Hence, i1(t) = (vm/Rn)cosωt A, and i2(t) = (–vm/(n2R))cosωt A

Chapter 13, Solution 45.

48 Ω

+
4∠–90˚ − Z

j
ZL = 8 − = 8 − j4 , n = 1/3
ωC
 ZL
Z= = 9 Z L = 72 − j36
n2
4∠ − 90° 4∠ − 90°
I= = = 0.03193∠ − 73.3°
48 + 72 − j36 125.28∠ − 16.7°

We now have some choices, we can go ahead and calculate the current in the second loop
and calculate the power delivered to the 8-ohm resistor directly or we can merely say that
the power delivered to the equivalent resistor in the primary side must be the same as the
power delivered to the 8-ohm resistor. Therefore,

I2
P8Ω = 72 = 0.5098x10 − 3 72 = 36.71 mW
2

The student is encouraged to calculate the current in the secondary and calculate the
power delivered to the 8-ohm resistor to verify that the above is correct.

Chapter 13, Solution 46.

(a) Reflecting the secondary circuit to the primary, we have the circuit shown below.

Zin

+ I1 +
16∠60° 10∠30°/(–n) = –5∠30°
− −

Zin = 10 + j16 + (1/4)(12 – j8) = 13 + j14

–16∠60° + ZinI1 – 5∠30° = 0 or I1 = (16∠60° + 5∠30°)/(13 + j14)

Hence, I1 = 1.072∠5.88° A, and I2 = –0.5I1 = 0.536∠185.88° A

(b) Switching a dot will not effect Zin but will effect I1 and I2.

I1 = (16∠60° – 5∠30°)/(13 + j14) = 0.625 ∠25 A

and I2 = 0.5I1 = 0.3125∠25° A

Chapter 13, Solution 47.

0.02 F becomes 1/(jωC) = 1/(j5x0.02) = –j10

We apply mesh analysis to the circuit shown below.

–j10

I3

10 Ω
3:1
+ +
+ +
10∠0° – v1 v2
I1 I2 vo 2Ω
− −
−

For mesh 1, 10 = 10I1 – 10I3 + v1 (1)

For mesh 2, v2 = 2I2 = vo (2)

For mesh 3, 0 = (10 – j10)I3 – 10I1 + v2 – v1 (3)

At the terminals, v2 = nv1 = v1/3 (4)

I1 = nI2 = I2/3 (5)

From (2) and (4), v1 = 6I2 (6)

Substituting this into (1), 10 = 10I1 – 10I3 (7)

Substituting (4) and (6) into (3) yields

0 = –10I1 – 4I2 + 10(1 – j)I3 (8)

From (5), (7), and (8)
 1 − 0.333 0   I1   0 
 10 6 − 10  I 2  = 10

− 10 −4 10 − j10  I 3   0 
 ∆2 100 − j100
I2 = = = 1.482∠32.9°
∆ − 20 − j93.33

vo = 2I2 = 2.963∠32.9° V

(a) Switching the dot on the secondary side effects only equations (4) and (5).

v2 = –v1/3 (9)

I1 = –I2/3 (10)

From (2) and (9), v1 = –6I2

Substituting this into (1),

10 = 10I1 – 10I3 – 6I2 = (23 – j5)I1 (11)

Substituting (9) and (10) into (3),

0 = –10I1 + 4I2 + 10(1 – j)I3 (12)

From (10) to (12), we get
 1 0.333 0   I1   0 
 10 −6 − 10  I 2  = 10

− 10 4 10 − j10  I 3   0 

∆2 100 − j100
I2 = = = 1.482∠–147.1°
∆ − 20 + j93.33

vo = 2I2 = 2.963∠–147.1° V

Chapter 13, Solution 48.

We apply mesh analysis.

8Ω 2:1 10 Ω

+ +
• •
+ V1 V2
I1 - j6 Ω
o
100∠0 V - I2
-
Ix
-j4 Ω
 100 = (8 − j 4) I 1 − j 4 I 2 + V1 (1)

0 = (10 + j 2) I 2 − j 4 I 1 + V 2 (2)
But
V2 1
=n= 
→ V1 = 2V2 (3)
V1 2

I2 1
= − = −2 
→ I 1 = −0.5 I 2 (4)
I1 n

Substituting (3) and (4) into (1) and (2), we obtain

100 = (−4 − j 2) I 2 + 2V2 (1)a

0 = (10 + j 4) I 2 +V2 (2)a

Solving (1)a and (2)a leads to I2 = -3.5503 +j1.4793

I x = I 1 + I 2 = 0.5 I 2 = 1.923∠157.4 o A

Chapter 13, Solution 49.

1 1
ω = 2, F 
→ = − j10
20 jω C

Ix -j10

2Ω I1 1:3 I2

1 2
+ • +
+ V1 V2
6Ω
12<0o V - -
- •
At node 1,

12 − V1 V1 − V2
= + I1 
→ 12 = 2 I 1 + V1 (1 + j 0.2) − j 0.2V2 (1)
2 − j10
At node 2,
V − V2 V2
I2 + 1 = 
→ 0 = 6 I 2 + j 0.6V1 − (1 + j 0.6)V2 (2)
− j10 6

1
At the terminals of the transformer, V2 = −3V1 , I 2 = − I1
3
Substituting these in (1) and (2),

12 = −6 I 2 + V1 (1 + j 0.8), 0 = 6 I 2 + V1 (3 + j 2.4)

Adding these gives V1=1.829 –j1.463 and

V1 − V2 4V1
Ix = = = 0.937∠51.34 o
− j10 − j10

i x = 0.937 cos(2t + 51.34 o ) A

Chapter 13, Solution 50.

The value of Zin is not effected by the location of the dots since n2 is involved.

Zin’ = (6 – j10)/(n’)2, n’ = 1/4

Zin’ = 16(6 – j10) = 96 – j160

Zin = 8 + j12 + (Zin’ + 24)/n2, n = 5

Zin = 8 + j12 + (120 – j160)/25 = 8 + j12 + 4.8 – j6.4

Zin = (12.8 + j5.6) ohms

Chapter 13, Solution 51.

Let Z3 = 36 +j18, where Z3 is reflected to the middle circuit.

ZR’ = ZL/n2 = (12 + j2)/4 = 3 + j0.5

Zin = 5 – j2 + ZR’ = (8 – j1.5) ohms

I1 = 24∠0°/ZTh = 24∠0°/(8 – j1.5) = 24∠0°/8.14∠–10.62° = 8.95∠10.62° A

Chapter 13, Solution 52.

For maximum power transfer,

40 = ZL/n2 = 10/n2 or n2 = 10/40 which yields n = 1/2 = 0.5

I = 120/(40 + 40) = 3/2

p = I2R = (9/4)x40 = 90 watts.

Chapter 13, Solution 53.

(a) The Thevenin equivalent to the left of the transformer is shown below.
8Ω

+
20 V
−

The reflected load impedance is ZL’ = ZL/n2 = 200/n2.

For maximum power transfer, 8 = 200/n2 produces n = 5.

(b) If n = 10, ZL’ = 200/10 = 2 and I = 20/(8 + 2) = 2

p = I2ZL’ = (2)2(2) = 8 watts.

Chapter 13, Solution 54.

(a) ZTh
I1

+
VS −
ZL/n2
For maximum power transfer,

ZTh = ZL/n2, or n2 = ZL/ZTh = 8/128

n = 0.25

(b) I1 = VTh/(ZTh + ZL/n2) = 10/(128 + 128) = 39.06 mA

(c) v2 = I2ZL = 156.24x8 mV = 1.25 V

But v2 = nv1 therefore v1 = v2/n = 4(1.25) = 5 V

Chapter 13, Solution 55.

We reflect Zs to the primary side.

ZR = (500 – j200)/n2 = 5 – j2, Zin = Zp + ZR = 3 + j4 + 5 – j2 = 8 + j2

I1 = 120∠0°/(8 + j2) = 14.552∠–14.04°

Zp
1:n

+ I2
Vp − I1 Zs

Since both currents enter the dotted terminals as shown above,

I2 = –(1/n)I1 = –1.4552∠–14.04° = 1.4552∠166°

S2 = |I2|2Zs = (1.4552)(500 – j200)

P2 = Re(S2) = (1.4552)2(500) = 1054 watts

Chapter 13, Solution 56.

We apply mesh analysis to the circuit as shown below.

2Ω 1:2
+ +
v1 v2

+
− −
46V I1 I2 10 Ω
−

5Ω

For mesh 1, 46 = 7I1 – 5I2 + v1 (1)

For mesh 2, v2 = 15I2 – 5I1 (2)

At the terminals of the transformer,

v2 = nv1 = 2v1 (3)

I1 = nI2 = 2I2 (4)

Substituting (3) and (4) into (1) and (2),

46 = 9I2 + v1 (5)

v1 = 2.5I2 (6)

Combining (5) and (6), 46 = 11.5I2 or I2 = 4

P10 = 0.5I22(10) = 80 watts.

Chapter 13, Solution 57.

(a) ZL = j3||(12 – j6) = j3(12 – j6)/(12 – j3) = (12 + j54)/17

Reflecting this to the primary side gives

Zin = 2 + ZL/n2 = 2 + (3 + j13.5)/17 = 2.3168∠20.04°

I1 = vs/Zin = 60∠90°/2.3168∠20.04° = 25.9∠69.96° A(rms)

I2 = I1/n = 12.95∠69.96° A(rms)

(b) 60∠90° = 2I1 + v1 or v1 = j60 –2I1 = j60 – 51.8∠69.96°

v1 = 21.06∠147.44° V(rms)

v2 = nv1 = 42.12∠147.44° V(rms)

vo = v2 = 42.12∠147.44° V(rms)

(c) S = vsI1* = (60∠90°)(25.9∠–69.96°) = 1554∠20.04° VA

Chapter 13, Solution 58.

Consider the circuit below.

20 Ω

I3

20 Ω
1:5
+ +
+ +
80∠0° – v1 v2
I1 I2 vo 100 Ω
− −
−

For mesh1, 80 = 20I1 – 20I3 + v1 (1)

For mesh 2, v2 = 100I2 (2)

 For mesh 3, 0 = 40I3 – 20I1 which leads to I1 = 2I3 (3)

At the transformer terminals, v2 = –nv1 = –5v1 (4)

I1 = –nI2 = –5I2 (5)

From (2) and (4), –5v1 = 100I2 or v1 = –20I2 (6)

Substituting (3), (5), and (6) into (1),

4 = I1 – I2 – I 3 = I1 – (I1/(–5)) – I1/2 = (7/10)I1

I1 = 40/7, I2 = –8/7, I3 = 20/7

p20(the one between 1 and 3) = 0.5(20)(I1 – I3)2 = 10(20/7)2 = 81.63 watts

p20(at the top of the circuit) = 0.5(20)I32 = 81.63 watts

p100 = 0.5(100)I22 = 65.31 watts

Chapter 13, Solution 59.

We apply nodal analysis to the circuit below.

2Ω

I3

8Ω
v1 I1 2 : 1 I2
v2
+ +
+
20∠0° – v1 v2
4Ω
− −
 20 = 8I1 + V1 (1)

V1 = 2I3 + V2 (2)

V2 = 4I2 (3)

At the transformer terminals, v2 = 0.5v1 (4)

I1 = 0.5I2 (5)

Solving (1) to (5) gives I1 = 0.833 A, I2 = 1.667 A, I3 = 3.333 A

V1 = 13.33 V, V2 = 6.667 V.

P8Ω = 0.5(8)|(20 – V1)/8|2 = 2.778 W

P2Ω = 0.5(2)I32 = 11.11 W, P4Ω = 0.5V22/4 = 5.556 W

Chapter 13, Solution 60.

(a) Transferring the 40-ohm load to the middle circuit,

ZL’ = 40/(n’)2 = 10 ohms where n’ = 2

10||(5 + 10) = 6 ohms

We transfer this to the primary side.

Zin = 4 + 6/n2 = 4 + 96 = 100 ohms, where n = 0.25

I1 = 120/100 = 1.2 A and I2 = I1/n = 4.8 A

4Ω 5Ω
I1 1:4 I2 I2 ’
+ +
+ v1 v2 10 Ω 10 Ω
120∠0° –
− −

Using current division, I2’ = (10/25)I2 = 1.92 and I3 = I2’/n’ = 0.96 A

(b) p = 0.5(I3)2(40) = 18.432 watts

Chapter 13, Solution 61.

We reflect the 160-ohm load to the middle circuit.

ZR = ZL/n2 = 160/(4/3)2 = 90 ohms, where n = 4/3

2Ω 14 Ω
I1 1:5 Io Io ’
+ +
+ v1 vo 60 Ω 90 Ω
24∠0° –
− −

14 + 60||90 = 14 + 36 = 50 ohms

We reflect this to the primary side.

ZR’ = ZL’/(n’)2 = 50/52 = 2 ohms when n’ = 5

I1 = 24/(2 + 2) = 6A

24 = 2I1 + v1 or v1 = 24 – 2I1 = 12 V

vo = –nv1 = –60 V, Io = –I1 /n1 = –6/5 = –1.2

Io‘ = [60/(60 + 90)]Io = –0.48A

I2 = –Io’/n = 0.48/(4/3) = 0.36 A

Chapter 13, Solution 62.

(a) Reflect the load to the middle circuit.

ZL’ = 8 – j20 + (18 + j45)/32 = 10 – j15

We now reflect this to the primary circuit so that

Zin = 6 + j4 + (10 – j15)/n2 = 7.6 + j1.6 = 7.767∠11.89°, where n =

5/2 = 2.5

I1 = 40/Zin = 40/7.767∠11.89° = 5.15∠–11.89°

S = 0.5vsI1* = (20∠0°)(5.15∠11.89°) = 103∠11.89° VA

 (b) I2 = –I1/n, n = 2.5

I3 = –I2/n’, n = 3

I3 = I1/(nn’) = 5.15∠–11.89°/(2.5x3) = 0.6867∠–11.89°

p = 0.5|I2|2(18) = 9(0.6867)2 = 4.244 watts

Chapter 13, Solution 63.

Reflecting the (9 + j18)-ohm load to the middle circuit gives,

Zin’ = 7 – j6 + (9 + j18)/(n’)2 = 7 – j6 + 1 + j12 = 8 + j4 when n’ = 3

Reflecting this to the primary side,

Zin = 1 + Zin’/n2 = 1 + 2 – j = 3 – j, where n = 2

I1 = 12∠0°/(3 – j) = 12/3.162∠–18.43° = 3.795∠18.43A

I2 = I1/n = 1.8975∠18.43° A

I3 = –I2/n2 = 632.5∠161.57° mA

Chapter 13, Solution 64.

We find ZTh at the terminals of Z by considering the circuit below.

10 Ω 1:n

+• • +
V1 V2
+
– –
I1 I2 1V
–
20 Ω
For mesh 1, 30 I 1 + 20 I 2 + V1 = 0 (1)

For mesh 2, 20 I 1 + 20 I 2 + V2 = 1 (2)

I1
At the terminals, V2 = nV1 , I2 = −
n

Substituting these in (1) and (2) leads to

(20 − 30n) I 2 + V1 = 0, 20(1 − n) I 2 + nV1 = 1

Solving these gives

1 1
I2 = 
→ Z Th = = 30n 2 − 40n + 20 = 7.5
30n − 40n + 20
2
I2

Solving the quadratic equation yields n=0.5 or 0.8333

Chapter 13, Solution 65.

40 Ω

10 Ω I1 1:2 I2 50 Ω I2 1:3 I3

1 • +• • 2
+ + + +
200 V V3 V4
(rms) V1 V2 - - 20 Ω
- - -
•

At node 1,

200 − V1 V1 − V4
= + I1 
→ 200 = 1.25V1 − 0.25V4 + 10 I 1 (1)
10 40
At node 2,

V1 − V4 V4
= + I3 
→ V1 = 3V4 + 40 I 3 (2)
40 20

At the terminals of the first transformer,

V2
= −2 
→ V2 = −2V1 (3)
V1

I2
= −1 / 2 
→ I 1 = −2 I 2 (4)
I1

For the middle loop,

− V2 + 50 I 2 + V3 = 0 
→ V3 = V2 − 50 I 2 (5)

At the terminals of the second transformer,

V4
=3 
→ V4 = 3V3 (6)
V3

I3
= −1 / 3 
→ I 2 = −3 I 3 (7)
I2

We have seven equations and seven unknowns. Combining (1) and (2) leads to

200 = 3.5V4 + 10 I 1 + 50 I 3

But from (4) and (7), I 1 = −2 I 2 = −2(−3I 3 ) = 6 I 3 . Hence

200 = 3.5V4 + 110 I 3 (8)

From (5), (6), (3), and (7),

V4 = 3(V2 − 50 I 2 ) = 3V2 − 150 I 2 = −6V1 + 450 I 3

Substituting for V1 in (2) gives

19
V4 = −6(3V4 + 40 I 3 ) + 450 I 3 
→ I3 = V4 (9)
210
Substituting (9) into (8) yields

200 = 13.452V4 
→ V4 = 14.87

V 24
P= = 11.05 W
20

Chapter 13, Solution 66.

v1 = 420 V (1)

v2 = 120I2 (2)

v1/v2 = 1/4 or v2 = 4v1 (3)

I1/I2 = 4 or I1 = 4 I2 (4)

Combining (2) and (4),

v2 = 120[(1/4)I1] = 30 I1

4v1 = 30I1

4(420) = 1680 = 30I1 or I1 = 56 A

Chapter 13, Solution 67.

V1 N 1 + N 2 1
(a) = = 
→ V2 = 0.4V1 = 0.4 x 400 = 160 V
V2 N2 0 .4

5000
(b) S 2 = I 2V2 = 5,000 
→ I2 = = 31.25 A
160

5000
(c ) S 2 = S1 = I 1V1 = 5,000 
→ I2 = = 12.5 A
400
Chapter 13, Solution 68.

This is a step-up transformer. I2

N1 v2
2 – j6
I1 10 + j40
+
N2
+
v1 −
20∠30° −
−

For the primary circuit, 20∠30° = (2 – j6)I1 + v1 (1)

For the secondary circuit, v2 = (10 + j40)I2 (2)

At the autotransformer terminals,

v1/v2 = N1/(N1 + N2) = 200/280 = 5/7,

thus v2 = 7v1/5 (3)

Also, I1/I2 = 7/5 or I2 = 5I1/7 (4)

Substituting (3) and (4) into (2), v1 = (10 + j40)25I1/49

Substituting that into (1) gives 20∠30° = (7.102 + j14.408)I1

I1 = 20∠30°/16.063∠63.76° = 1.245∠–33.76° A

I2 = 5I1/7 = 0.8893∠–33.76° A

Io = I1 – I2 = [(5/7) – 1]I1 = –2I1/7 = 0.3557∠146.2° A

p = |I2|2R = (0.8893)2(10) = 7.51 watts

Chapter 13, Solution 69.

We can find the Thevenin equivalent.

+ I2 +

N2
75 Ω j125 Ω v2
VTh
I1 +
N1
+
v1
120∠0° −
−
−
−

I1 = I2 = 0

As a step up transformer, v1/v2 = N1/(N1 + N2) = 600/800 = 3/4

v2 = 4v1/3 = 4(120)/3 = 160∠0° rms = VTh.

To find ZTh, connect a 1-V source at the secondary terminals. We now have a
step-down transformer.

+ I1

75 Ω j125 Ω v1
+
I2 1∠0° V −
+
v2
−
−

v1 = 1V, v2 =I2(75 + j125)

But v1/v2 = (N1 + N2)/N1 = 800/200 which leads to v1 = 4v2 = 1

and v2 = 0.25

I1/I2 = 200/800 = 1/4 which leads to I2 = 4I1

 Hence 0.25 = 4I1(75 + j125) or I1 = 1/[16(75 + j125)

ZTh = 1/I1 = 16(75 + j125)

Therefore, ZL = ZTh* = (1.2 – j2) kΩ

Since VTh is rms, p = (|VTh|/2)2/RL = (80)2/1200 = 5.333 watts

Chapter 13, Solution 70.

This is a step-down transformer.

30 + j12
I1
+

v1 I2
+ +
120∠0° −
v2
20 – j40
− −

I1/I2 = N2/(N1 + N2) = 200/1200 = 1/6, or I1 = I2/6 (1)

v1/v2 = (N2 + N2)/N2 = 6, or v1 = 6v2 (2)

For the primary loop, 120 = (30 + j12)I1 + v1 (3)

For the secondary loop, v2 = (20 – j40)I2 (4)

Substituting (1) and (2) into (3),

120 = (30 + j12)( I2/6) + 6v2

and substituting (4) into this yields

120 = (49 – j38)I2 or I2 = 1.935∠37.79°

p = |I2|2(20) = 74.9 watts.

Chapter 13, Solution 71.

Zin = V1/I1

But V1I1 = V2I2, or V2 = I2ZL and I1/I2 = N2/(N1 + N2)

Hence V1 = V2I2/I1 = ZL(I2/I1)I2 = ZL(I2/I1)2I1

V1/I1 = ZL[(N1 + N2)/N2] 2

Zin = [1 + (N1/N2)] 2ZL

Chapter 13, Solution 72.

(a) Consider just one phase at a time.

1:n
A
a

B 20MVA
Load
b

C
c

n = VL/ 3VLp = 7200 /(12470 3 ) = 1/3

(b) The load carried by each transformer is 60/3 = 20 MVA.

Hence ILp = 20 MVA/12.47 k = 1604 A

ILs = 20 MVA/7.2 k = 2778 A

(c) The current in incoming line a, b, c is

3I Lp = 3x1603.85 = 2778 A

Current in each outgoing line A, B, C is

2778/(n 3 ) = 4812 A
Chapter 13, Solution 73.

(a) This is a three-phase ∆-Y transformer.

(b) VLs = nvLp/ 3 = 450/(3 3 ) = 86.6 V, where n = 1/3

As a Y-Y system, we can use per phase equivalent circuit.

Ia = Van/ZY = 86.6∠0°/(8 – j6) = 8.66∠36.87°

Ic = Ia∠120° = 8.66∠156.87° A

ILp = n 3 ILs

I1 = (1/3) 3 (8.66∠36.87°) = 5∠36.87°

I2 = I1∠–120° = 5∠–83.13° A

(c) p = 3|Ia|2(8) = 3(8.66)2(8) = 1.8 kw.

Chapter 13, Solution 74.

(a) This is a ∆-∆ connection.

(b) The easy way is to consider just one phase.

1:n = 4:1 or n = 1/4

n = V2/V1 which leads to V2 = nV1 = 0.25(2400) = 600

i.e. VLp = 2400 V and VLs = 600 V

S = p/cosθ = 120/0.8 kVA = 150 kVA

pL = p/3 = 120/3 = 40 kw

4:1
IL ILs

VLp VLs
Ips
Ipp
 But pLs = VpsIps

For the ∆-load, IL = 3 Ip and VL = Vp

Hence, Ips = 40,000/600 = 66.67 A

ILs = 3 Ips = 3 x66.67 = 115.48 A

(c) Similarly, for the primary side

ppp = VppIpp = pps or Ipp = 40,000/2400 = 16.667 A

and ILp = 3 Ip = 28.87 A

(d) Since S = 150 kVA therefore Sp = S/3 = 50 kVA

Chapter 13, Solution 75.

(a) n = VLs/( 3 VLp) 4500/(900 3 ) = 2.887

(b) S = 3 VLsILs or ILs = 120,000/(900 3 ) = 76.98 A

ILs = ILp/(n 3 ) = 76.98/(2.887 3 ) = 15.395 A

Chapter 13, Solution 76.

(a) At the load, VL = 240 V = VAB

VAN = VL/ 3 = 138.56 V

Since S = 3 VLIL then IL = 60,000/(240 3 ) = 144.34 A

 1:n
0.05 Ω j0.1 Ω
A

240V
2640V 0.05 Ω j0.1 Ω Balanced
Load
B 60kVA
0.85pf
0.05 Ω j0.1 Ω leading
C

(b) Let VAN = |VAN|∠0° = 138.56∠0°

cosθ = pf = 0.85 or θ = 31.79°

IAA’ = IL∠θ = 144.34∠31.79°

VA’N’ = ZIAA’ + VAN

= 138.56∠0° + (0.05 + j0.1)(144.34∠31.79°)

= 138.03∠6.69°

VLs = VA’N’ 3 = 137.8 3 = 238.7 V

(c) For Y-∆ connections,

n = 3 VLs/Vps = 3 x238.7/2640 = 0.1569

fLp = nILs/ 3 = 0.1569x144.34/ 3 = 13.05 A

Chapter 13, Solution 77.

(a) This is a single phase transformer. V1 = 13.2 kV, V2 = 120 V

n = V2/V1 = 120/13,200 = 1/110, therefore n = 110

(b) P = VI or I = P/V = 100/120 = 0.8333 A

I1 = nI2 = 0.8333/110 = 7.576 mA

Chapter 13, Solution 78.

The schematic is shown below.

k = M / L1 L 2 = 1 / 6 x 3 = 0.2357

In the AC Sweep box, set Total Pts = 1, Start Freq = 0.1592 and End Freq = 0.1592.
After simulation, the output file includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 4.253 E+00 –8.526 E+00

FREQ IM(V_PRINT2) IP(V_PRINT2)

1.592 E–01 1.564 E+00 2.749 E+01

From this, I1 = 4.253∠–8.53° A, I2 = 1.564∠27.49° A

The power absorbed by the 4-ohm resistor = 0.5|I|2R = 0.5(1.564)2x4

= 4.892 watts
Chapter 13, Solution 79.

The schematic is shown below.

k1 = 15 / 5000 = 0.2121, k2 = 10 / 8000 = 0.1118

In the AC Sweep box, we type Total Pts = 1, Start Freq = 0.1592, and End Freq =
0.1592. After the circuit is saved and simulated, the output includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 4.068 E–01 –7.786 E+01

FREQ IM(V_PRINT2) IP(V_PRINT2)

1.592 E–01 1.306 E+00 –6.801 E+01

FREQ IM(V_PRINT3) IP(V_PRINT3)

1.592 E–01 1.336 E+00 –5.492 E+01

Thus, I1 = 1.306∠–68.01° A, I2 = 406.8∠–77.86° mA, I3 = 1.336∠–54.92° A

Chapter 13, Solution 80.

The schematic is shown below.

k1 = 10 / 40 x80 = 0.1768, k2 = 20 / 40 x 60 = 0.482

k3 = 30 / 80x 60 = 0.433

In the AC Sweep box, we set Total Pts = 1, Start Freq = 0.1592, and End Freq =
0.1592. After the simulation, we obtain the output file which includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 1.304 E+00 6.292 E+01

i.e. Io = 1.304∠62.92° A
Chapter 13, Solution 81.

The schematic is shown below.

k1 = 2 / 4x8 = 0.3535, k2 = 1 / 2 x8 = 0.25

In the AC Sweep box, we let Total Pts = 1, Start Freq = 100, and End Freq = 100.
After simulation, the output file includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.000 E+02 1.0448 E–01 1.396 E+01

FREQ IM(V_PRINT2) IP(V_PRINT2)

1.000 E+02 2.954 E–02 –1.438 E+02

FREQ IM(V_PRINT3) IP(V_PRINT3)

1.000 E+02 2.088 E–01 2.440 E+01

i.e. I1 = 104.5∠13.96° mA, I2 = 29.54∠–143.8° mA,

I3 = 208.8∠24.4° mA.
Chapter 13, Solution 82.

The schematic is shown below. In the AC Sweep box, we type Total Pts = 1, Start Freq
= 0.1592, and End Freq = 0.1592. After simulation, we obtain the output file which
includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 1.955 E+01 8.332 E+01

FREQ IM(V_PRINT2) IP(V_PRINT2)

1.592 E–01 6.847 E+01 4.640 E+01

FREQ IM(V_PRINT3) IP(V_PRINT3)

1.592 E–01 4.434 E–01 –9.260 E+01

i.e. V1 = 19.55∠83.32° V, V2 = 68.47∠46.4° V,

Io = 443.4∠–92.6° mA.

Chapter 13, Solution 83.

The schematic is shown below. In the AC Sweep box, we set Total Pts = 1, Start Freq
= 0.1592, and End Freq = 0.1592. After simulation, the output file includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 1.080 E+00 3.391 E+01

FREQ VM($N_0001) VP($N_0001)

1.592 E–01 1.514 E+01 –3.421 E+01

i.e. iX = 1.08∠33.91° A, Vx = 15.14∠–34.21° V.

Chapter 13, Solution 84.

The schematic is shown below. We set Total Pts = 1, Start Freq = 0.1592, and End
Freq = 0.1592. After simulation, the output file includes

FREQ IM(V_PRINT1) IP(V_PRINT1)

1.592 E–01 4.028 E+00 –5.238 E+01

FREQ IM(V_PRINT2) IP(V_PRINT2)

1.592 E–01 2.019 E+00 –5.211 E+01

FREQ IM(V_PRINT3) IP(V_PRINT3)

1.592 E–01 1.338 E+00 –5.220 E+01

i.e. I1 = 4.028∠–52.38° A, I2 = 2.019∠–52.11° A,

I3 = 1.338∠–52.2° A.
Chapter 13, Solution 85.

Z1

+
VS −
ZL/n2

For maximum power transfer,

Z1 = ZL/n2 or n2 = ZL/Z1 = 8/7200 = 1/900

n = 1/30 = N2/N1. Thus N2 = N1/30 = 3000/30 = 100 turns.

Chapter 13, Solution 86.

n = N2/N1 = 48/2400 = 1/50

ZTh = ZL/n2 = 3/(1/50)2 = 7.5 kΩ

Chapter 13, Solution 87.

ZTh = ZL/n2 or n = Z L / Z Th = 75 / 300 = 0.5

Chapter 13, Solution 88.

n = V2/V1 = I1/I2 or I2 = I1/n = 2.5/0.1 = 25 A

p = IV = 25x12.6 = 315 watts

Chapter 13, Solution 89.

n = V2/V1 = 120/240 = 0.5

S = I1V1 or I1 = S/V1 = 10x103/240 = 41.67 A

S = I2V2 or I2 = S/V2 = 104/120 = 83.33 A

Chapter 13, Solution 90.

(a) n = V2/V1 = 240/2400 = 0.1

(b) n = N2/N1 or N2 = nN1 = 0.1(250) = 25 turns

(c) S = I1V1 or I1 = S/V1 = 4x103/2400 = 1.6667 A

S = I2V2 or I2 = S/V2 = 4x104/240 = 16.667 A

Chapter 13, Solution 91.

(a) The kVA rating is S = VI = 25,000x75 = 1875 kVA

(b) Since S1 = S2 = V2I2 and I2 = 1875x103/240 = 7812 A

Chapter 13, Solution 92.

(a) V2/V1 = N2/N1 = n, V2 = (N2/N1)V1 = (28/1200)4800 = 112 V

(b) I2 = V2/R = 112/10 = 11.2 A and I1 = nI2, n = 28/1200

I1 = (28/1200)11.2 = 261.3 mA

(c) p = |I2|2R = (11.2)2(10) = 1254 watts.

Chapter 13, Solution 93.

(a) For an input of 110 V, the primary winding must be connected in parallel, with
series-aiding on the secondary. The coils must be series-opposing to give 12 V. Thus the
connections are shown below.

110 V
12 V

(b) To get 220 V on the primary side, the coils are connected in series, with series-
aiding on the secondary side. The coils must be connected series-aiding to give 50 V.
Thus, the connections are shown below.

220 V

50 V
Chapter 13, Solution 94.

V2/V1 = 110/440 = 1/4 = I1/I2

There are four ways of hooking up the transformer as an auto-transformer. However it is

clear that there are only two outcomes.

V1 V1 V1 V1

V2 V2 V2 V2

(1) (2) (3) (4)

(1) and (2) produce the same results and (3) and (4) also produce the same results.
Therefore, we will only consider Figure (1) and (3).

(a) For Figure (3), V1/V2 = 550/V2 = (440 – 110)/440 = 330/440

Thus, V2 = 550x440/330 = 733.4 V (not the desired result)

(b) For Figure (1), V1/V2 = 550/V2 = (440 + 110)/440 = 550/440

Thus, V2 = 550x440/550 = 440 V (the desired result)

Chapter 13, Solution 95.

(a) n = Vs/Vp = 120/7200 = 1/60

(b) Is = 10x120/144 = 1200/144

S = VpIp = VsIs

Ip = VsIs/Vp = (1/60)x1200/144 = 139 mA