CS4700/2700 Controllers

Technical Reference
for use with
46 and 66 Series Electric Fastening Tools
and SD25 Electric Screwdrivers
Rev 0.7 November 30, 2005
CP P/N :
Techmotive P/N : 39-30-43083

CP Techmotive
22705 Heslip Drive
Novi, Michigan 48375 USA

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

24-Hour
Technical Support
Toll Free in the U.S. and Canada:
1-877-224-7377
All other countries:
(001) 248-348-6280
between 8 a.m. and 5 p.m.
Eastern Standard Time (EST)

NOTE: Chicago Pneumatic Tool Company (CP) in 2005

acquired and changed the name of GSE tech-motive tool
to CP Techmotive. Product Information may be found on
www.cp.com.

NOTE: The part number for the Visual Supervisor (VS) software
program is 464000-03330 (CP part number 6150040915)

NOTE: A variety of related technical manuals in .pdf format

may be downloaded from www.cp.com. Click on the
Technical Info link on the left column. Select Technical
Documentation. Scroll through the list to find the title of
the product you require, and click!

CP Techmotive manufactures products under the CP, CP Techmotive, and tech-motive tool brand names
Information and technical diagrams in this manual are subject to change without notice. techmotive tool is a
registered trademark. Products and services referred to in this book may be either trademarks and/or registered
trademarks of their respective owners.

____________________________________________________________________________________________
Page 2
39-30-43083

Safety:
Working with fastening tools can be dangerous if safe and proper procedures are not followed. As
with all machinery, certain hazards can be involved with the operation of the product. Using these
tools with respect and caution will considerably lessen the possibility of personal injury. If, however,
safety precautions are overlooked or ignored personal injury to the operator can result.
Always use common sense and exercise caution when using these tools. They can produce high
torque that, unless properly compensated for, could cause personal injury. Remember, your personal
safety is your responsibility.
If you are an operator or CP Techmotive qualified service technician, you should become familiar
with the contents of this manual before operating, servicing, or maintaining any part of the 4700/2700
Controller. Familiarization with all components of the system can minimize the possibility that an
accident or injury might occur.
CP Techmotive assumes no responsibility for personal injury or damage to equipment resulting from
misuse of these tools. After reviewing this manual you should also review all safety procedures
provided by your company and the equipment installer.
WARNING!

Failure to follow these steps can result in serious personal

injury.

General Machine Safety

FOR YOUR OWN SAFETY READ THE INSTRUCTION MANUAL THOROUGHLY

PRIOR TO OPERATING THE TOOL.

DO NOT WORK IN A DANGEROUS ENVIRONMENT. Do not use power tools in a damp

or wet location or explosive atmosphere, or expose them to rain, oils, or corrosive fluids.

KNOW THE LOCATION OF POWER DISCONNECTS AND EMERGENCY STOP

BUTTONS PRIOR TO OPERATING THIS EQUIPMENT.

KEEP ALL ELECTRICAL PANELS CLOSED DURING OPERATION. High voltage

present inside enclosure panels can result in personal injury. Do NOT bypass or defeat
electrical safety devices. Turn the power actuator to the OFF position prior to any servicing
or maintenance of the controller.

Observe all government and/or company power lockout standards.

NEVER OPERATE SOLENOID VALVES, LIMIT SWITCHES OR RELAYS

MANUALLY as this practice can create dangerous, unexpected machine movements.

SECURE THE TOOL. Tools that develop torque can produce hazardous torque reactions.
Always be sure that the tool is properly fixtured to absorb reaction as a fastener is tightened.
Never operate a tool capable of high torque without proper fixturing.

SECURE WORK. Avoid situations where the part being fastened breaks loose and can cause
damage.

NEVER TOUCH OR ATTEMPT TO STOP MOVING MACHINERY OR PARTS WITH

YOUR HANDS, OTHER PARTS OF YOUR BODY, OR MAKESHIFT DEVICES.

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

DO NOT OPERATE THE TOOL WHILE UNDER THE INFLUENCE OF

ALCOHOL, DRUGS OR MEDICATION THAT CAN IMPAIR YOUR
JUDGMENT.

REPORT ALL UNSAFE WORKING CONDITIONS OR PRACTICES TO YOUR

SUPERVISOR AND / OR SAFETY DEPARTMENT FOR CORRECTION.

WEAR APPROVED SAFETY GLASSES AT ALL TIMES.

DO NOT WEAR JEWELRY, especially bracelets and rings, while operating the
fastening tools. Keep hands and fingers away from all rotating parts and avoid
situations where clothing can become tangled in the tool. Secure loose fitting
clothing, neckties, and long hair. Wear medical alert identification cautiously.

DO NOT OVERREACH. Keep proper footing and balance at all times.

KEEP YOUR WORK AREA CLEAN. Do not work on or near slippery floors or
surfaces. Avoid situations where the tool reacts against unexpected obstacles. Do not
operate electrical equipment while standing on a wet floor.

MAINTAIN TOOLS IN TOP CONDITION. Keep tools properly lubricated and

clean. If any wires become frayed or exposed, replace them immediately. Prevent
dirt, grease or contaminants from getting into the tool.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Be careful how the tool

is left unattended. Avoid resting it on its throttle lever to prevent false starts.

CONTROL THE DIRECTION OF ROTATION. The reaction torque changes

direction when going from forward to reverse. Always be aware in which direction
the tool will rotate prior to using it. If the tool is not fixtured this will allow you to
brace for the proper direction of torque reaction.

CHECK DAMAGED PARTS. Before further use of a tool, any part of the tool that
is damaged should be carefully checked to ensure that it will operate properly and
perform its intended function. Check for alignment of moving parts, breakage of
parts, mounting, and any other conditions that may affect its operation. Never
operate a tool that has damaged or exposed wires. Never operate a tool that has any
part of the powertrain, other than the output spindle, exposed.

Electrical Safety
Only qualified and properly trained personnel should perform electrical/electronic
troubleshooting and repair. Consider the following electrical system safety
guidelines:

Before you troubleshoot or service a fastening system station, be sure you have an
up-to-date and appropriate set of electrical drawings for that station.

Remove metal items, such as rings, metal necklaces, wristwatches and jewelry, as
these can create electrical hazards. Wear medical alert identification cautiously.

Wear safety glasses, but avoid wearing those that have metal rims or metal side
shields.

It may be necessary to troubleshoot equipment while the power is ON. ONLY

qualified, trained personnel should do this. During these instances, open only the

____________________________________________________________________________________________
Page 2
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

panels, doors, or covers, which need to be opened. Know the voltage present at all
points before you begin troubleshooting.

Use properly insulated tools when working on electrical equipment to reduce the
possibility of shock. Make sure the insulation is adequate to safeguard against the
high voltages present.

If you must work on the electrical system, be sure the main disconnect switch on the
power panel is in the OFF position and locked out with locks from each trade
involved in the repair.

Do not attempt to modify or repair the machine without the approval of the proper
authorities.

Uses approved fuse pullers when changing fuses.

Never use jumper wires or fuse substitutes to replace specified fuses.

Always use fuses of a capacity smaller than or equal to the safe capacity of the line
or the equipment it serves.

Before you work on any circuit, check it with an appropriate testing device to be
sure voltage is not present.

Install temporary wiring as safely as possible and replace it with permanent wiring
as soon as possible. Install grounding wherever it is needed in the final installation.
If modifications are made to the system wiring, drawings must be revised to
illustrate this change.

Know how to deal with electrical fires properly. Keep carbon dioxide and powder
extinguishers handy.

Earth Connection
Make sure that the controller is properly grounded via a protective conductor. The tool is connected to
earth by means off a ground wire internal to the cable via the controller. This protects the operator
from any electric shock.

Differential circuit breaker

The controller is fitted with a differential circuit breaker for user protection. This device detects any
insulation defect in the cable or in the tool. The tool will stop when a leakage current is 30 mA or
more; is detected by the device. The device will protect the operator from any electric shock and
protects the servo drive from deterioration of the power stages. The device can be reset manual by
resetting the trip switch to the ON position. See Exterior Component Section for location.

Software Features
Their are several feature build into the software to protect the operator from being injured because of
joint, servo and tool problems; Lock rotor, high limit torque shutoff, high limit angle shutdown,
temperature shutdown, tool communication failures, 120 % of the tools capacity. Any of these failures
will be displayed on the tool control module.
Locked rotor Power being supplied to tools motor but no rotation on the output spindle
Temperature shutdown Motor temp sensor open because of excessive heat build in motor
High Limit Shutdown Tool shutdown because high limit torque was exceeded
High Angle Limit Shutdown Tool shutdown because high limit angle was exceeded
Tool Communication Cable bad, Intelligence tool interface printed circuit board failed
____________________________________________________________________________________________
September 2005
Page 3

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Preface
The CS4700/2700 controllers are functionally equivalent to the CS4100/2100. In fact, most of the
internal electronics and software is identical. The CS4700/2700 packaging has been improved to be
smaller and lighter.
The CS4700/2700 Controller manufactured by CP techmotive tool is a component of one of the most
powerful DC electric nutrunner fastening control systems available. The system uses 100% digital
technology from the tool to ensure accurate and reliable fastening and data acquisition.
Microprocessors in both the fastening tool and the controllers tool control module (TCM) enable the
system to perform to levels of accuracy while providing easy set-up and operation previously
unattainable. With Intelligent tool technology you no longer need to enter tool identification,
calibration, angle counts, speed and other information. You simply plug in the tool, power on the
system, program the desired tightening specifications and begin production.
A complete nutrunner fastening control system is made up of one of the following:
* A CS4700 Controller with a CP techmotive tool 56, 66 or 116 Series nutrunner, 27 A tool control
module (TCM) and cable
* A CS4746 Controller with a 46 Series nutrunner, 8 A TCM and cable
* A CS2700 Controller with a SD25 electric screwdriver, 6 A TCM and cable
The CP techmotive tool Visual Supervisor software program is used for system setup, fastening, data
collection, and diagnostics although basic programming can be done by a local keypad and display on
some models.

Who Should Use This Manual

This manual is written for the engineers, technicians and users who will set-up and/or operate the
CS4700/4746/2700 Controller with their respective nutrunner or screwdriver models listed above.

How to Use This Manual

This manual provides installation, maintenance and technical information about the CS4700/2700
Controllers.
This Preface provides conventions and abbreviations used throughout this manual.
It is recommended that you read this manual entirely before you use a CS47XX/2700 Controller.
This manual may have some illustrations and text that applies to the latest firmware:
CCM 1.13
DCM 6.16
VS 3.33

____________________________________________________________________________________________
Page 4
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Conventions
The following conventions are used throughout CP techmotive tool manuals for the safety of
personnel, equipment, software, and data. (Not all of these conventions are used in every manual or
guide.) The conventions include warnings, cautions and notes, as follows:
WARNING!

!
CAUTION!

i
NOTE:

It can be dangerous to personnel and/or machine systems,

if operating instructions are not followed. The information
appears in a box in italicized boldface type.

There may be damage to equipment, and loss of software

and data, if operating instructions are not followed. The
information is indented and in italicized boldface type.

Information that adds to your knowledge of the equipment

and/or software. The information is indented and italicized.

Abbreviations
Some of the most common abbreviations used throughout this manual include the following:
AIM
API
CCM
E2PROM
I/O
IEEE
EPR
IP
LED
PLC
TCM
TCP/IP
TDM
SDLC
V
VS

Anybus Interface Module (a PC board) used whenever a Field-bus option is added

application program interface (Usually a PC based program generic interface)
Communications control module (a PC board) used to add Ethernet and other options
electrically-erasable programmable read-only memory (holds the program on the DCM,
CCM, TDM and AIM)
input/output
Institute of Electrical and Electronic Engineers
error-proofing ready
internet protocol
light emitting diode
programmable logic controller
tool control module (the central box which contains tool controller CPU & Servo)
transmission control protocol/internet protocol
techmotive display module (a PC board)
synchronous data link control (CP techmotive tools RS-485 protocol)
volts
Visual Supervisor - the setup, fastening, data collection, and diagnostics software
program developed by CP techmotive tool

____________________________________________________________________________________________
September 2005
Page 5

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Table of Contents
Product Dimensions, Weights and Power requirements .............................. 7
Product Compatibility Information ................................................................. 8
CS4700 Part Number Codes ............................................................................ 9
CS4700 General Information.......................................................................... 10
Location of Major Components .................................................................... 13
Keypad & Display operation .......................................................................... 14
Console/Diagnostic Port ............................................................................... 17
Printer/Barcode Port ...................................................................................... 18
Communications Methods (Ethernet/SDLC/RS232) ..................................... 20
Fieldbus .......................................................................................................... 23
Default mapping
Std (Standard mapping)
GM8/GM4
Bcin (Barcode special)
SEQ (Sequences special)
Determining INPUT sources .......................................................................... 29
DeviceNet ........................................................................................................ 31
Profibus .......................................................................................................... 33
Ethernet/IP & Modbus-TCP ............................................................................ 37
Optional CCM PC boards and Layouts ......................................................... 40
CCM+
AIM
TDM
Special Applications ...................................................................................... 44
PFCS
GM
FORD
Screwdriver and Specialty tool applications
General TROUBLESHOOTING ....................................................................... 53
CS4700 Data flow block diagram (Focus on Barcodes) .............................. 54

____________________________________________________________________________________________
Page 6
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Product Dimensions and Weight

F1

F2

F3

2
ABC

F4

3
DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

+/-

CLR

ENTER

DIMENSIONS in INCHES

Weight:
Approximate Weight = 30 LBS. (Weight will vary slightly depending on configuration)

Input Voltage Requirements:

CS2700 (115v) - 115vac +15%,-10%; 50/60 Hz (.5 to .75 kva recommended)
CS2700 (230v) - 230vac +15%,-10%; 50/60 Hz (.5 to .75 kva recommended)

(If supplied with 230v only TCMs)

CS4746 - 230vac +15%, -10%; 50/60 HZ
CS4700 - 230vac +15%, -10%; 50/60 HZ

(.75 to 1 kva recommended)

(.75 to 1 kva recommended)

(If supplied with 115/230v Dual voltage TCMs)

CS4746 - 115vac or 230vac +15%, -10%; 50/60 HZ
CS4700 - 115vac or 230vac +15%, -10%; 50/60 HZ

(.75 to 1 kva recommended)

(.75 to 1 kva recommended)

Note: Voltage levels can effect the maximum speed capability. The supply (kva) can
effect the ability of the tool to achieve rated torque especially on soft joints.

____________________________________________________________________________________________
September 2005
Page 7

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Product Compatibility Information

TCM compatibility

230v (or) 115/230v (Dual voltage capable)

230v (or) 115v (Screwdrivers)

Revision & Part#

It is generally recommended that 230vac (versus 115vac) be used in most industrial

applications since periodic power loading can result in supply-line drops that could limit torque
capability on soft-joint (demanding) torque applications
The 4700 and 4746 (66 and 46 series tools) can be equipped with TCMs which are dual
voltage capable (115v or 230vac nominal). Please consult factory if 115v (or dual voltage
capability is required). (See table below)
The TCM models (dual voltage capable) are backward compatible which means they
will work in any current or older controller. Please notice that some CS4700 models require a
revision K or higher TCM to operate properly.
Generally, plugging in an incompatible TCM will not cause any damage but will result
in the following:
1. It will work fine (but it may only run at 230vac)
2. It wont power-up at all (If TCM older than rev. K and that model required rev. K)

CONTROLLER

TCM requirements

115v CS2700 (Screwdriver)

230v CS2700 (Screwdriver)

49-4100-01C2
49-4100-01C3

All revisions
Revision K or higher

CS4700 plastic-connector (230v)

(115/230v)
CS4746 plastic-connector (230v)
(115/230v)
CS4700 SMC metal conn. (230v)
(115/230v)
CS4746 SMC metal conn. (230v)
(115/230v)

49-4100-03C5
49-4100-03C5D
49-4100-01C5L
49-4100-01C5LD
49-4100-03C5
49-4100-03C5D
49-4100-01C5L
49-4100-01C5LD

All revisions (But 230v operation only)

Dual Voltage capable
All revisions (But 230v operation only)
Dual Voltage capable
Rev. K or higher (But 230v operation only)
Dual Voltage capable
Rev. K or higher (But 230v operation only)
Dual Voltage capable

____________________________________________________________________________________________
Page 8
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Product Part Number Codes

Product part# C4700 A 0 1 K 2 1 6 054
2 Screwdriver
4 46/56/66
Codes for special options
(See Below)

00 66/56 Series
(or SD25 Screwdriver)

46 46 Series
Pset Select Switch
P Present
0 Not Present

K Keypad
V VS reqd

1 115V
(C2100 only)
2 230V **

2 Standard Screwdriver conn.

6 Plastic tool connector
7 Metal (SMC) tool connector

Notes: ** - The 4700 & 4746 models are capable of DUAL voltage (115/230v) if supplied with Dual-voltage
capable TCMs.

Special SUFFIX Codes

ASSIGNMENTS: (Subject to change)
1-PFCS (Ethernet)
2-Reserved
3-Reserved
4-DeviceNet
5-Ethernet (10 Base-T)

6-Interbus-S
7-Modbus-Plus
8-Profibus-DP/DPV1
9-Reserved
A-Ethernet-IP /Modbus TCP
B- PFCS (RS232 Terminal Server)

Other Letters: Future use

NOTE:

When Ethernet is present, DaimlerChrysler PFCS Ethernet is

always available. Likewise GM and Ford interfaces are
available on Ethernet-capable units.

____________________________________________________________________________________________
September 2005
Page 9

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

CS4700 General Information

Units with Keypad/Display
If the controller has a Keypad/Display, you may simply connect the tool, go into the Menu and select
Defaults (pick TOOL I/O). This provides a quick way to get up and running immediately. On these
units, you may prefer to use the Visual Supervisor (VS) program initially for even easier setup
especially if the process is complex.
NOTE:

When setting up these defaults it is also possible to select the

source of the TOOL commands (fieldbus or the tool switches)
and the source of the parameter selections (fieldbus, physical
I/O or the keypad menu). If you require I/O mapping that is not
among the default selections, VS will be required to customize
these input sources.

Use +/- key on RUN screen to adjust contrast

Use Decimal-pt. on RUN screen to REVERSE blue/white

Units without Keypad/Display

Controllers without the Keypad/Display must be configured using the VS software. If the unit is
Ethernet capable, some of the configuration (like setting up IP addresses, etc.) must be done via the
RS-232 console port. The default selections can also be done via the RS-232 console if necessary.
VS should be used to fine-tune selections/parameters.

Units with Ethernet/Fieldbus Capability

Many models are supplied with Ethernet capability. This Ethernet link can go to CP techmotive tools
VS-embedded system software or to an API interface or to a number of selectable custom software
interfaces for Ford, GM and DaimlerChrysler. The controller can also be upgraded with one of a
number of standard fieldbus interfaces. These will enable interfacing to PLCs via a standard bus to
provide data and I/O exchange.

All Units with CCMs

A Communications Control Module (CCM) is added whenever Ethernet, a keypad/display or a
fieldbus is required. Whenever the CS4700 has a CCM, you may need to connect to the CCM via the
DIAGNOSTICS RS-232 port on the bottom panel of the controller. By running HyperterminalCONSOLE (at 9,600 baud), a text-based dialog will allow you to set the TCP/IP address and other
parameters as well as to perform extended diagnostics. Examples of this dialog are found later in this
document. Remember: when making critical changes be sure to initiate the COMMIT command to
store all of the requested changes permanently into E2PROM. Note that newer revisions of software
permit editing of various Ethernet parameters via the keypad/display.

____________________________________________________________________________________________
Page 10
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

CCM+ Based Block Diagram

FIELD Upgrade Considerations

CS4700/4746/2700 Controllers are considered BASIC models if they have only a TCM. Adding a
CCM makes the unit Ethernet capable. With the CCM in place, it is possible to add the Fieldbus
capability and/or the Keypad/Display option. Keep in mind that E2PROMs exist on the TCM, CCM,
Anybus Interface Module (AIM) and techmotive device module (TDM), which may be updated
periodically. Beginning with CCM version 1.07 and with WinFlash 1.12 or higher, it is possible to
flash upgrade the TDM, AIM or even the TCM via the CCM Flash port connection.

____________________________________________________________________________________________
September 2005
Page 11

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Units with CCM+ (Ethernet capable)

All Flash updates can be done simply from the CS4700 Controller RS-232 computer port without
going inside the box or moving any cables (as required of the original CCM units).
CP Techmotive Winflash
Utility - the primary
connection to the CCM
Downstream devices
and software revisions

NOTE:

WinFlash is CP techmotive tools software update utility

applicable to the CCM, CCM+, or direct TCM connection.

Save/Restore with VS3.33 & CCM1.11 (or higher rev.)

Upgrading to VS3.33 and CCM1.11 provides the ability to save and restore the complete CS4700
setup. Previous versions of software would not save the settings associated with the CCM and
Fieldbus entities. Within VS files such as .vsc and .dev can save the CS4700 configuration and
restore it. These files contain this additional information as extended data. If trying to restore a
CS4700 from a file and it didnt have the hardware for this extended data, the CCM will still
restore but it will just throw away the extended setup data that it cannot use.

____________________________________________________________________________________________
Page 12
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Location of Major Components

CS2700 with Door open

TCM

Internal Frame of CS2700

AIM
(Fieldbus Module)

TDM

CCM
(Communications
Module
)

(Display Module)

Internal ITI board

Bottom Connector bd

Backplane

(CS2700 only)

24vdc power supplies

Digital I/O power
CCM & add-on option power

Line Filter

GFCI

Circuit Breaker / On-Off switch

____________________________________________________________________________________________
September 2005
Page 13

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Keypad/Display Operation
Entering SETPOINTS Via the Keypad
The detachable version of VS (VS loaded onto a laptop PC that is connected to the controller) can be
used as an enhanced local programming facility, as not all setpoint functions are available via the
keypad. Connecting detachable VS will disable the ability to change setpoints via the controller
keypad until the computer running detachable VS is disconnected.

VS Embedded Connections
Embedded VS (available when a controller has a built-in industrial computer and monitor) can be
used via the Ethernet port or SDLC (RS-485 port).
NOTE:

If the unit is Ethernet-capable, SDLC (RS-485) is available only

on CCM+ based units. Changes made by the controller keypad
or detachable VS will be immediately reflected on the
embedded VS screen. The VS Embedded PC can also be used
to change the settings. In these environments, it may be
desirable to implement security (refer to the next paragraph).

SECURITY: Visual Supervisor and the Keypad

The CS4700 with Keypad/Display can be set up with passwords and multiple access levels. Security
is set up using the VS program VsUserMgt (VS3.28 or higher is required). VS allows an almost
infinite number of users with individual levels of security to use the system. However, only five
special passwords can be sent to the controller for security at the keypad and VS-Detachable level.
These special passwords are called Plant Floor Security Passwords, and they must be numeric. You
must use the VsUserMgt utility and a USB key to set these up.
NOTE:

The embedded version of VS will load the Plant Floor Security

passwords into the CS4700 Controller when VsMain starts.
Make sure the VS Icon
is removed from the tool tray and restart VsStart to have the Plant Floor Security settings transferred.
The detachable version of VS can also load the CS4700 with the
passwords, but the mechanism is different. You must enter into
VsSetup and click setup, and then select Load Plant Floor
SecuritySettngs. The lock icon indicates that the Plant Floor
Security Password is resident in the controller.

____________________________________________________________________________________________
Page 14
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

LIMITATIONS of the Keypad

The optional Keypad/Display provides continuous information about torque, angle, parameter sets
(psets) and cycle counts. It also allows you to select psets and change many setpoints from the
keypad. Special programming configurations and many of the less frequently used parameters are not
available via the keypad, so if these must be changed then VS must be connected to the controller.
Additionally, some very application-specific functions (and TCP/IP setup) must be done via Hyperterminal on the RS-232 setup/diagnostics port.

STATISTICS Available on Controller with Keypad/Display

A statistics function has been provided to show torque and angle statistics based on a selected sample
size. The top of the screen shows the active parameter set and the number of samples that have been
collected in the current sample data group. The rest of the screen shows the statistics from the
previously completed data group.

HISTORY Available on Controller with Keypad/Display

In the history mode, the user can view the results of the last 10 cycles. Note that the TCM maintains a
much larger history buffer which can be extracted via Visual Supervisor software. Also note that the
size of the TCM history depends on the History mode setting.

____________________________________________________________________________________________
September 2005
Page 15

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Keypad Display Characteristics

If a setpoint falls outside of the tools capability or internally contradicts the operation of the tool, the
setpoint change will be rejected. You may still need to connect the VS program to address some setup
issues.
Current Status

Last Cycle Declaration

Last Cycle Count#

Peak/Final Torque
Final Angle
(if applicable)
Time of Last Cycle

CS4700 TCP/IP address

Applicable Ethernet
Connection programs
armed (shows API, PFCS.
VS and others possible)

Last Cycle
Parameter Set #

VS is set up to talk via

RS-485 (address #5
Fieldbus and
miscellaneous information

tech-motive Display
Module & S/W Verson

All software resident

within the
CS4700/4746/2700
Controller

____________________________________________________________________________________________
Page 16
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Comm/Diag (Comm. RS232 Setup & Diagnostics )

A null-modem cable that provides an RS-232 connection (typically 9 pin-d female on both ends) is
required for setup of the CCM module. This cable plugs into the CS4700 Mini Controller
Comm/Diag port.
Digital I/O connector

Tool Connector
SDLC Network (RS485)
(In and Out Connectors)
VS (RS-232) DETACHABLE
(and Flash upgrade port for CCM+)

Ethernet connection
(RS232)
Printer output
(Barcode input)

For the Debug/Setup port, use 9600 baud, 8 data, no parity and one stop bit. (Typically COM1 will be
used for the RS-232 serial connection.) When you press the ENTER key, a > should appear. Press
? to display a list of available commands. (In the captured text on the next page, the user entered the
larger-bold text, and the rest was the response from the CCM.) Future CCM revisions may may add
or modify the commands.

CAUTION!

DO NOT TURN OFF POWER to the CS4700 controller while

making setup changes on the Console (Debug/Setup) port, as
the setting changes may be lost. You must issue one of the
COMMIT commands to enact/save most of configuration
settings. Any of the COMMIT commands will preserve all of
the setting change categories.

____________________________________________________________________________________________
September 2005
Page 17

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Printer/Barcode (RS232 Printer output & barcode input)

PRINTER PORT Characteristics: OUTPUT ONLY 9600 baud (8 data, no parity, 1 stop bit).
Data stream is sent without handshaking following each cycle.
----------------SAMPLE PRINTER OUTPUT FORMAT (TCM backplane DIP Sw # 8 OFF)----------#0110 Sp:01-01 H 15.1 Nm L 3 Deg
#0110
Sp:
01
01
H
XX15.1
NmXXX
L
XXXXX3
Deg

Cycle count
Space
Spindle header
Spindle number
Dash
Parameter number
Space
Torque Pass/Fail*
Peak torque
Space
Torque Units
Spaces
Angle Pass/Fail
Angle result
Space
Angle Units
Carriage return
Line feed

(5 bytes)
(1 byte)
(3 bytes)
(2 bytes)
(1 byte)
(2 bytes)
(1 byte)
(1 byte)
(6 bytes)
(1 byte)
(6 bytes)
(1 bytes)
(1 byte)
(6 bytes)
(1 byte)
(3 bytes)
(1 byte)
(1 byte)

------------------SAMPLE PRINTER OUTPUT FORMAT (TCM backplane DIP Sw # 8 ON)---------#0095 Sp:01-01PP 13.0 4.0 10.1P 9999 40 36
#0095
Sp:
01
01
P
P
X13.0
XX4.0
X10.1
P
X9999
XXX40
XXX36

Cycle count
Spindle name*
Spindle header
Spindle number
Dash
Parameter number
Overall Pass/Fail
Torque Pass/Fail
High Limit
Low Limit
Torque Peak
Angle Pass/Fail
Angle High Limit
Angle Low Limit
Angle Result
Carriage return
Line feed

(5 bytes)
(5 bytes)
(3 bytes)
(2 bytes)
(1 byte)
(2 bytes)
(1 byte)
(1 byte)
(5 bytes)
(5 bytes)
(5 bytes)
(1 byte)
(5 bytes)
(5 bytes)
(5 bytes)
(1 byte)
(1 byte)

*If Spindle Name > 6 then the Spindle name field will increase to that length (up to 32 characters).

____________________________________________________________________________________________
Page 18
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

BARCODE PORT Characteristics: INPUT ONLY 9600 baud (8 data, no parity, 1 stop bit).
Note that this RS232 INPUT port will watch for specially formatted input strings for the purpose of AutoCal. from an instrument such as the M290 Torque Audit device.
Refer to Visual Supervisor Manual for Barcode setup and capability details. Some of the selectable
modes and options are as follows:
1.
2.
3.
4.
5.
6.

Attaching an identifier (Part ID, Model# or both) to each cycle

Forcing a barcode read before allowing the tool to run
Using a barcode to select a parameter set
Discriminate barcodes with Masking and Min/Max Length options
Use a barcode to attach to data continuously or one-barcode per cycle
Assignable I/O for clearing, bypassing and monitoring the barcode statuses

Note: In addition to this RS232 port, barcodes can also enter into the TCM for marrying to cycle data
via Fieldbus and from VS (PC software).

Date, Time and Time Zone Settings

When the controller is connected to a PC running Visual-Supervisor, the controller will synchronize to the
computers date, time and Time-zone settings automatically.
If the controller is setup up totally independent of Visual-Supervisor (Like the unit with Keypad/Display) the user
should either link to Visual-Supervisor momentarily (to synchronize to the local time settings of the PC) or go into
the console settings and set the Date, Time and Time-zone settings. These settings can be found under the
DATE section of the console.

____________________________________________________________________________________________
September 2005
Page 19

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Connecting to Visual Supervisor (Ethernet)

.

Setting Up and Configuring the Single-Channel Controller

1.
2.

3.
4.

Determine the TCP/IP address information that will be designated for CS47XX/2700 Controller.
On the console session above, use the ipconfig command to enter in this information.
Typically; the mask may be something like 255.255.255.0; the Gateway 0.0.0.0
Keypad/Display units allow entering in this information via the keypad.
Verify that the VS bridge is enabled. The command ipconfig +vseth might be needed if not.
Be sure to use the commit command to save the settings permanently if using the console.

Linking VS to the Single-Channel Controller on Ethernet

1.
2.

At the VS Host Computer run VsSystemSettings.

Set up the controller as an Ethernet connection and enter in the IP address (from above)
VS should now link to this controller. Some computer software FIREWALLS may
try to block this connection depending on how they are configured.
3. If you have problems, use the PING command to debug, and observe the CCMs LEDs.)
NOTE
:

Once a CCM has linked to a VS-embedded host on

Ethernet, the CCM will ignore any other attempted VS
connections (other than IP addresses) over the Ethernet.
Powering the controller down and then up is required to
clear the CCM of the expected IP address for its VS host
connection.

Connecting to Visual Supervisor (SDLC RS-485)

Use the console command ipconfig +vssdlc to enable VS on SDLC (RS-485).
UNITS WITHOUT CCM+
CS2700

TCM backplane DIP switches set SDLC address

CS4700/4746

TCM backplane DIP switches set SDLC address

UNITS WITH CCM+

CS2700

NOT SDLC capable

CS4700/4746

CCM+ Dip switches set SDLC address

Connecting to Visual Supervisor (RS-232)

The RS-232 computer port on the bottom of the CS4700 Controller provides an RS-232 (laptop PC
Detachable VS) connection. Typically the baud rate is set for 57.6 kbaud, provided that TCM
backplane DIP switch #7 is on; otherwise, the baud rate is 9,600 baud. On units with the CCM+, the
baud rate will be 57.6 kbaud regardless of the TCM backplane DIP switch.

____________________________________________________________________________________________
Page 20
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Sample Console Session

____________________________________________________________________________________________
September 2005
Page 21

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Examples of Network Topologies (CS4100 = CS4700)

____________________________________________________________________________________________
Page 22
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Fieldbus Capabilities
The CS4700 Contoller can interface to one field bus: DeviceNet, Profibus, Ethernet-IP and others are
available in order to exchange I/O and data with PLCs and other devices.
Only certain hard-coded data mapping configurations are available over fieldbus. Presently, enabling
the fieldbus I/O and selecting the data type can be done via the Console/Debug port. And some
functions can be enabled (by default) via the Keypad/Display if the controller is so equipped.
Most of the specific setup for the fieldbus is done via the console AIM category.
Under this category there is a BYTE-ORDER setting also known as Little Endian and Big
Endian. This is done as some PLCs and computers expect the high byte/low byte to be sent in
different order. This setting will effect the 4- byte FLOAT values as well as the 2-byte INTEGER
values. The sample below shows an example of a system running Little Endian which is the
DEFAULT mode.
Sample DeviceNet Host program
Showing CS4700 output bytes (Default data config.)
(See next page)

CS4700 shows torque = 36.1 (Ntm)

42104211 converted to FLOAT = 36.0645 (Ntm)

CS4700 Console (Comm/Diag) AIM Diagnostics

1st byte=Output bits, 2nd-5th bytes=Torque, 6th&7th byte=Angle
60
11 42 10 42
A8 00

____________________________________________________________________________________________
September 2005
Page 23

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

FieldBus Data Mapping Types:

Default - ..Small General purpose data mapping
Std (Standard) . Expanded output data and setpoints
GM8 & GM4 - .. Special purpose for specific customer
Bcin (Barcode in) Expanded I/O with 2 barcode inputs
SEQ (Sequences) Expanded I/O with Full Sequence bits

TYPE: Default:
Outputs
Byte

Bit

Description

0
1
2
3
4
5
6
7
0-7
0-7

Parameter Set Selected Bit 0

Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Parameter Set Selected Bit 3
System Fault
Cycle Finished
Cycle Good
Cycle Bad
Peak Torque (IEEE Floating Point)
Final Angle (16 bit integer, 0 to 65535)

Byte

Bit

Description

0
1
2
3
4
5
6
7

Parameter/Sequence Select Bit 0

Parameter/Sequence Select Bit 1
Parameter/Sequence Select Bit 2
Parameter Set Select Bit 3
Cycle Enable
Cycle On
Forward
Clear Outputs

1-4
5-6

Inputs

____________________________________________________________________________________________
Page 24
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

TYPE: Std (standard)

Outputs
Byte

Bit

Description

0
1
2
3
4
5
6
7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7

Parameter Set Selected Bit 0

Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Parameter Set Selected Bit 3
System Fault
Cycle Finished
Cycle Good
Cycle Bad
Peak Torque (IEEE Floating Point)
Final Angle (16 bit integer, 0 to 65535)
Torque HighLimit (IEEE Floating Point)
Torque Target (IEEE Floating Point)
Torque LowLimit (IEEE Floating Point)
Torque Fastening Threshold (IEEE Floating Point)
Torque Control Reference (IEEE Floating Point)
Angle HighLimit (16 bit integer, 0 to 65535)
Angle Target (16 bit integer, 0 to 65535)
Angle LowLimit(16 bit integer, 0 to 65535)
Speed Rundown (16 bit integer, 0 to 65535)
Speed Downshift (16 bit integer, 0 to 65535)
Tool Serial Number (Hex value) * see Note 1
VIN# (7 characters)
* see Note 2

1-4
5-6
7-10
11-14
15-18
19-22
23-26
27-28
29-30
31-32
33-34
35-36
37-40
41-47

NOTE 1:

Most CP techmotive tool serial numbers are 4 characters (1234),

however, some are represented in 8 characters (2C03 1234) which
includes year and month information.

History Mode (in VsSystemSettings ) must be set to a setting other

than Standard:
If a VIN is received that is greater than 20 characters, and
Reduced Rundown with PartId-Barcode is configured, the lower
7 characters of the right-most 20 will be selected.
If Reduced Rundown with Model # Barcode is configured, the
lower 7 characters of the left-most 20 will be selected.
If History mode is set to Standard, the VIN# will NOT be sent over
fieldbus.
If History mode is set to Standard with Both barcodes the
MODEL# barcode will be sent.

NOTE 2:

Inputs
Byte

Bit

Description

0
1
2
3
4
5
6
7

Parameter/Sequence Select Bit 0

Parameter/Sequence Select Bit 1
Parameter/Sequence Select Bit 2
Parameter Set Select Bit 3
Cycle Enable
Cycle On
Forward
Clear Outputs

____________________________________________________________________________________________
September 2005
Page 25

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

TYPE: GM8/GM4
Outputs
NOTE:

The difference between GM4 & GM8 is that GM8 mode adds
the PVI on the inputs

?
Byte

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3
4
5-7
0
1
2
3-7
0-7

Bypass
Release 1 Job
Unused
Unused
Parameter Set Selected Bit 0
Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Global Accept
InCycle
Unused
System Fault
Cycle Finished
EPR
Unused
Good
GM Red
GM Yellow
Unused
Unused

Byte

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3
4-7
0-7
0-7
0-7

Stack Light Green

Stack Light Yellow
Stack Light Red
Stack Light Alarm
Parameter Set Select Bit 0
Parameter Set Select Bit 1
Parameter Set Select Bit 2
unused
Cycle On
Reverse
EPR
Stop/Disable
Unused
Unused
Unused
PVI
*GM8 mode only

Inputs

2
3
4-7

For any INPUTS entering the controller via fieldbus, make sure that these functions are not mapped to
physical inputs into the controller (via VS). Currently, if the CCM recognizes a fieldbus connection
with inputs it will not allow inputs via OPC.

____________________________________________________________________________________________
Page 26
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

TYPE: Bcin (Barcode input)

st

NOTE:

This option is 1 available in CCM version 1.10.

?
Outputs
Byte

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7

Parameter Set Selected Bit 0

Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Parameter Set Selected Bit 3
System Fault
Cycle Finished
Cycle GOOD
Cycle BAD
Ready
Bypassed
Sequence GOOD
Sequence BAD
Part-ID barcode received ok
Model# barcode received ok
Spare
Output#4 (Mappable via VS)
Peak Torque (IEEE Floating Point)
Final Angle (16 bit integer, 0 to 65535)

Byte

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3-7

Parameter Set Selected Bit 0

Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Parameter Set Selected Bit 3
Cycle Enable
Cycle On
Forward
Clear Outputs
Clear Barcode
Clear Barcode Requirement
Batch/Sequence Abort
Spare
MODEL# Barcode (20 Characters)
PART-ID Barcode (20 Characters)

2-5
6-7

Inputs

2-21
22-41

____________________________________________________________________________________________
September 2005
Page 27

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

TYPE: SEQ (Sequence Support)

Outputs
Byte
0

3
4-7
8-9
10-13
14-17
18-21
22-23
24-25
26-27
28-31

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7
0-7

Sequence Set Selected Bit 0

Sequence Set Selected Bit 1
Sequence Set Selected Bit 2
Sequence Set Selected Bit 3 (Gen2 only..otherwise zero)
System Fault
Cycle Finished
Cycle GOOD
Cycle BAD
Ready
Sequence Finished
Sequence GOOD
Sequence BAD
Sequence Declared (In process)
Batch Finished
Batch Good
Batch Bad
Parameter Set Selected Bit 0
Parameter Set Selected Bit 1
Parameter Set Selected Bit 2
Parameter Set Selected Bit 3
Parameter Set Selected Bit 4
Bypassed
Spare
Yield Fault Detected
Spare
Peak Torque Result
Final Angle Result
Torque High Limit
Torque Target Limit
Torque Low Limit
Angle High Limit
Angle Target Limit
Angle Low Limit
Spare

Bit

Description

0
1
2
3
4
5
6
7
0
1
2
3-7
0-7

Parameter/Sequence Select Bit 0

Parameter/Sequence Select Bit 1
Parameter/Sequence Select Bit 2
Parameter/Sequence(Gen2 only) Select Bit 3
Cycle Enable
Cycle On
Forward
Clear Outputs
Parameter Select bit 4 (When using psets 17-32)
Reject Lockout Clear
Batch/Sequence Abort
Spare
Spare

Inputs
Byte
0

2-5

____________________________________________________________________________________________
Page 28
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Determining INPUT Sources

It is possible that INPUTS can enter into the single-channel CS4700 Controller from several sources.
Below is a list of some potential sources and their relative priority.
1.

2.
3.
4.
5.

VsSetup assignments
a. Tool switches
b. Digital inputs (via a 19-pin connector etc.)
c. Auto-increment or barcode-based pset selections
Ford specific I/O (but only if the Ford interface is enabled via the console port)
Keypad pset selection (if a keypad is resident and enabled by default or via the console)
Fieldbus (which must be enabled by defaults via keypad or console)
Note that if no keypad is present (Defaults should be set via the console)
OPC inputs via Visual Supervisor/Applicaton programs
NOTE:

Enabling Fieldbus will block all INPUTS from OPC.

?
Examples:
You want to start the tool via Fieldbus. Set Default#1 below.
NOTE:

If VsSetup is run and Cycle-On is mapped to a tool trigger or

an input, it will then override the Fieldbus input.

You want to start the tool via OPC. Set Default#3 below. You must run VsSetup and unmap the
cycle-On input from the tool switch.
DEFAULTS INPUT Mapping from the Keypad (or RS-232 Console)
In order to initiate a CS47XX/2700 Controller to operate without using VS, several Default modes
have been provided. These can be selected via the Main Menu screen or by invoking the console
Default command. The Default selections allow the user to select the source of the pset-selects and
the location from which the tool will be controlled. The 4 selections are:
DEFAULT#
1
2
3
4

Parameter Set select

Tool Running control

Fieldbus
Fieldbus
DCM physical I/O (or OPC)
Keypad

Fieldbus
Operator switches on tool
Operator switches on tool (or OPC)
Operator switches on tool

IMPORTANT
NOTE:

Selecting Default 1 or 2 (Fieldbus) will block any OPC changes. This

is important if VS is connected to a system running any Fieldbus I/O.
Also, Default #1 is SUGGESTED for any variations of Fieldbus
control, such as Cycle-enable from the PLC but the operator
wants to run the tool from the tool switches etc.

____________________________________________________________________________________________
September 2005
Page 29

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

For reference, the table below shows the input mapping for the DCM when one of the above defaults
(in the prior table) is selected. (For GM- or FORD-specific default input mapping, see the GM/Ford
special applications section).
DCM Input

DEFAULT#1

Input#1
Input#2
Input#3
Input#4
Input#5
Input#6
Input#7
Input#8
Tool Cycle trig.

Sync.
Calibrate

Tool Direction Sw
Tool Aux. Sw.

DEFAULT#2

DEFAULT#3

DEFAULT#4

Cycle-on,Enable,
Clear outputs
Forward

Cycle-on,Enable,
Clear outputs
Forward

Sync.
Calibrate

Cycle-on,Enable,
Clear outputs
Forward
Pset select 0
Pset select 1
Pset select 2
Sync.
Calibrate

Sync.
Calibrate

Cycle-on,Enable,
Clear outputs
Forward

Cycle-on,Enable,
Clear outputs
Forward

Cycle-on,Enable,
Clear outputs
Forward

OPC INPUTS for the CS4700 Controller

The OPC inputs (Cycle-On, Pset Select, etc.) via the computer through VsMain, although seldom
used, are available and have been used in some applications. A CS4700 Controller without a CCM
will work as it always has. However, a CS4700 with a CCM and either a Keypad/Display or Fieldbus
connection may or may not allow OPC inputs. In order for specific OPC inputs to operate the CS4700
Controller, Default #3 above must be selected via defaults (and those specific inputs unmapped
accordingly by VS).

Fieldbus INPUTS for the CS4700 Controller

In order for inputs to be sourced from a fieldbus, the controller must be equipped with the appropriate
AIM and fieldbus hardware. It is important to select DEFAULT (via keypad or console) for the
source of the inputs. For example, DEFAULT 1 or DEFAULT 2 would be necessary selections for
achieving reliable fieldbus inputs, especially if DEFAULT 3 or DEFAULT 4 can later override the
selected inputs and basically take away the fieldbus input via OPC.

Input Ownership
The Console command Status will report the owner of the most popular inputs. The CCM will
own the input if the keypad, fieldbus or the Ford-function has control. The DCM will own the
input if the input is sourced from the tool, physical inputs, OPC, or (barcode or auto-increment).

OUTPUTS (When Defaults are Selected on Keypad/Console)

(For GM specific default-output mapping see later section).
DCM Output

DEFAULT#1,2,3 or 4

Output#1
Output#2
Output#3
Output#4
Output#5
Output#6
Output#7
Output#8
Tool YELLOW
Tool GREEN
Tool RED

Finished
Good
Bad
In-Cycle
Direction
Sync.
U.S. Standard Yellow
U.S. Standard Green
U.S. Standard Red

____________________________________________________________________________________________
Page 30
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

DeviceNet (Slave) Setup and Configuration

Anybus
DeviceNet card

AIM board

(see AIM section)

.
5-pos DeviceNet connector
(see below for pinout)
8 Position Dip switch settings on DeviceNet card
DeviceNet
Baud Rate
125k
250k
500k
(Reserved)

SW.1
OFF
OFF
ON
ON

SW.
2
OFF
ON
OFF
ON

MAC
0
1
2

Internal X-bus
(CAN connections)

Sw3
Off
Off

Sw4
Off
Off

Sw5
Off
Off

Sw6
Off
Off

Sw7
Off
Off

Sw8
Off
On

Off

Off

Off

Off

On

Off

1
(Internal) DeviceNet Card (Side View)

5-pin Mini (male)

(Bulkhead)

LED #1
LED #2
LED #3

Mating cable for Mini conn:

Turck# B4151-0113.5
CP Techmotive#26-20-6740
PIN
1
2
3
4
5

LED#4
Pin #1 of 5 position connector on PC board

SIGNAL

PIN

SIGNAL

Shield
V+ (+24vdc)
V- (0 volt)
CAN_H
CAN_L

1
2
3
4
5

VCAN_L
Shield
CAN_H
V+

5 pin Mini-style
Bulkhead connector

5 pin Phoenix style

connector on pc
board

STATE
LED1-Reserved
LED2- Network
Status

LED3- Module
Status

LED4- Reserved

Description

--Off
Green steady
Green flash
Red steady
Red flash
Off
Green steady
Green flash
Red steady
Red flash

Off or Not online

Line OK, online, connected
On-line, not connected
Critical link failure
Connection timeout
No power to device
Device Operational
Data size bigger than config.
Unrecoverable fault
Minor Fault

---

By Default, 24vdc is expected to be supplied from

the DEVICENET network (See pin-2 above).

Status Indicators
Once the controller is powered up and the Devicenet module is initialized, LED #3 will be green, and
all others will be off (#2 may be flashing green, this is OK). Once communications is established with
the master, LED#2 will be steady green and LED#3 will remain on (as shown, above).

EDS file
An EDS file is available upon request which is applicable to this DeviceNet ANYBUS card.

____________________________________________________________________________________________
September 2005
Page 31

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Fieldbus Diagnostics Example for DeviceNet

(Debug Console)
>aim
Anybus Interface Module is active.
HW Config: 00, SW Version: 1.01
I/O mode: gm4 (4 bytes in, 4 bytes out)
Anybus Module is attached.
Vendor ID:
1
Serial Number:
A0017B83
Module SW Version: 1.09
Boot Loader Version: 1.34
Fieldbus Type:
25 - DeviceNet
Dip Switches:
0xBC
Address:
60
Baudrate:
500
AppInt SW Version: 2.16
Fieldbus SW Version: 1.06
Anybus Module is initialized.
Anybus Module is online.
Inputs from fieldbus = 00 00 00 00
Inputs to DCM
= 00 00 00 00
Outputs
= 00 00 00 00

>aim ?
'aim'
- Displays AIM status.
'aim io'
- Display the current state of the AIM I/O.
'aim +diag'
- Output AIM diagnostic data to the console.
'aim -diag'
- Turn off AIM diagnostic output.
'aim setmode <mode>' - Sets fieldbus mode.
modes:
default (1 byte in, 7 bytes out)
std
(1 byte in, 48 bytes out)
gm4 (4 bytes in, 4 bytes out)
gm8 (8 bytes in, 4 bytes out)
'aim config'
- Display DeviceNet node configuration.
'aim config addr<0 to 63> baud< 125,250,or 500 >'\n"
- Modifiy DeviceNet address/baud rate.
'aim config setmode <mode>'
modes:
ccm
(get addr/baud from the ccm)
switches1 (get addr/baud from switches)
switches2 (switches reverse ordered)
'aim byteorder big' - Configure for big endian (Motorola style) byte order
'aim byteorder little' - Configure for little endian (Intel style) byte order
'aim commit'
- Commit AIM settings to EEPROM storage.

>aim config
address
baud
mode

: 60
: 500
: switches1

____________________________________________________________________________________________
Page 32
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Profibus (Slave) Setup and Configuration

Profibus Module Status Indicators:

Once the controller is powered up and the profibus module is initialized, LED #3 will be red, and all
others will be off. Once communications is established with the master, LED#2 will be green, and all
others will be off. (as shown)

____________________________________________________________________________________________
September 2005
Page 33

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

____________________________________________________________________________________________
Page 34
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Profibus Network Configuration

Before the module can be used on a Profibus-DP network some basic settings must be configured.

Baud Rate
The baud rate on a Profibus-DP network is set during configuration from the master. The module
features auto baud rate detection and the user does not have to configure the baudrate.
Supported baud rates:
1. 9.6 kbit/s
2. 19.2 kbit/s
3. 45.45 kbit/s
4. 93.75 kbit/s
5. 187.5 kbit/s
6. 500 kbit/s
7. 1.5 Mbit/s
8. 3 Mbit/s
9. 6 Mbit/s
10. 12 Mbit/s

Node Address
The switches can be used when selecting a node address in the range 00-99.

Termination
Each bus segment in a Profibus network must be terminated properly to ensure error-free operation.
If the module is used as the first or last node in a network, the termination switch has to be in ON
position. Otherwise the switch has to be in OFF position.
NOTE:

If an external termination connector is used, the switch must be

in the OFF position.

GSD Configuration file

A GSD file is available upon request which is applicable to this Profibus-DPV1 ANYBUS card.

____________________________________________________________________________________________
September 2005
Page 35

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Fieldbus Diagnostics Example for Profibus

(Debug Console)
=======================================================================
Profibus
=======================================================================

aim

>
Anybus Interface Module is active.
HW Config: 00, SW Version: 1.02E
I/O mode: default (1 byte in, 7 bytes out)
Anybus Module is attached.
Vendor ID:
1
Serial Number:
A001B143
Module SW Version: 1.00
Boot Loader Version: 1.34
Fieldbus Type:
5 - Profibus-DPV1
Switches
25
Node Address
25
AppInt SW Version: 3.00
Fieldbus SW Version: 1.35
Anybus Module is initialized.
Anybus Module is not online.
>aim ?
'aim'
- Displays AIM status.
'aim io'
- Display the current state of the AIM I/O.
'aim +diag'
- Output AIM diagnostic data to the console.
'aim -diag'
- Turn off AIM diagnostic output.
'aim setmode <mode>' - Sets fieldbus mode.
modes:
default (1 byte in, 7 bytes out)
std
(1 byte in, 48 bytes out)
gm4 (4 bytes in, 4 bytes out)
gm8 (8 bytes in, 4 bytes out)
'aim config'
- Display Profibus node address
'aim config addr<0 to 126>' - Modify Profibus node address
'aim config setmode <mode>'
modes:
ccm
(get addr from the ccm)
switches (get addr from switches)
'aim byteorder big' - Configure for big endian (Motorola style) byte order
'aim byteorder little' - Configure for little endian (Intel style) byte order
'aim commit'
- Commit AIM settings to EEPROM storage.

>aim config
address
: 25
mode
: switches

____________________________________________________________________________________________
Page 36
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Ethernet/IP or Modbus/TCP (Slave)

Setup and Configuration

____________________________________________________________________________________________
September 2005
Page 37

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

NOTE:

Ethernet-IP/Modbus-TCP are considered fieldbus entities. Look

for the settings to be AIM commands rather than ipconfig
commands.

How to change between Ethernet IP and Modbus TCP Server Modes

To set to Modbus mode using the diags console, at the console prompt type aim config +modbus, then
press enter. This will disable the EthernetIP server on the anybus module.
>aim config +modbus
To set to EthernetIP mode using the diags console, type aim config +ethip, then press enter. This will
disable the Modbus-TCP server on the anybus module.
>aim config +ethip

LED functionality
For EthernetIP mode:
LED#3 will be solid green when the Master is connected (online).
LED#3 will flash green (at 1hz) when the Master is not connected (offline).
For ModbusTCP mode:
LED#3 will flash green when the Master is connected (online).
LED#3 will be off when the Master is not connected (offline).

DIP switch functionality

These switches are generally not used. It is possible to select the ARP setting (instead of CCM)
in the Console setup (AIM CONFIG SETMODE command). However the settings will be
forced to 192.168.0.n with a Mask of 255.255.255.0. Typically, the CCM mode is selected and
the user can have full control of setting the IP, Mask and Gateway settings.
>aim config setmode ccm

EDS configuration file

An EDS file is available upon request which is applicable to this Ethernet-IP capable card.

Modbus-TCP Special Information

Reading Outputs
The start address (byte zero) for reading outputs begins at address 0hex.

Writing Inputs
The start address (byte zero) for writing inputs begins at address 400hex (1024 decimal).

____________________________________________________________________________________________
Page 38
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Fieldbus Diagnostics Example for Ethernet-IP Setup

(Debug Console)
=======================================================================
EthernetIP (or Modbus-TCP)
=======================================================================

aim

>
Anybus Interface Module is active.
HW Config: 00, SW Version: 1.01
I/O mode: gm4 (4 bytes in, 4 bytes out)
Anybus Module is attached.
Vendor ID:
1
Serial Number:
A001B126
Module SW Version: 1.23
Boot Loader Version: 1.18
Fieldbus Type:
83 - Ethernet IP+IT
Dip Switches: 0x0
AppInt SW Version: 3.01
Fieldbus SW Version: 1.23
Anybus Module is initialized.
Anybus Module is online.
>

aim ?
'aim'
- Displays AIM status.
'aim io'
- Display the current state of the AIM I/O.
'aim +diag'
- Output AIM diagnostic data to the console.
'aim -diag'
- Turn off AIM diagnostic output.
'aim setmode <mode>' - Sets fieldbus mode.
modes:
default (1 byte in, 7 bytes out)
std (1 byte in, 48 bytes out)
gm4 (4 bytes in, 4 bytes out)
gm8 (8 bytes in, 4 bytes out)
'aim config' - Displays anybus module TCP/IP configuration.
'aim config addr <ip addr> mask <subnet mask> gateway <gateway>'
- Modifies anybus module TCP/IP configuration.
'aim config setmode <mode>' - Determines where to get the IP settings
modes:
ccm - IP settings from the ccm
arp - IP settings from External source
See module document
'aim byteorder big' - Configure for big endian (Motorola style) byte order
'aim byteorder little' - Configure for little endian (Intel style) byte order
'aim config +EthIP'
- connection type is EthernetIP
'aim config +Modbus'
- connection type is Modbus
'aim commit' - Commit AIM settings to EEPROM storage.

>

aim config
Physical Address : 00-30-11-02-15-56
IP Address
: 10.120.18.31
Subnet Mask : 255.255.252.0
Default Gateway : 10.120.16.1
mode
: ccm
connection
: EthIP

or Modbus if setup for Modbus-TCP

____________________________________________________________________________________________
September 2005
Page 39

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Optional PC-boards (Technical Details)

.

Communications Control Module (+) (CCM - CP p/n 420981-40311)

JP1 Battery connect
to non-volatile memory
RS-232 Diag

RS-232
Flash/VS

Remote
LEDs

Ethernet
10-base-T

Battery
#DL2430
(JP3) X-bus (CAN)
Termination jumper

SDLC to external
network

24 VDC in/out
CCM PLUS
MAC address etc.

SDLC to TCM

JP3

Diagnostic
LEDS

Options
SW2

CAN In & Out

SDLC Address
SW1

LED5 Green - Flashes when software is running

LED6 Yellow - Comm. to TCM via RS485/SDLC
LED7 Red Future
LED8 Red - VS Comm. on Ethernet activity
LED9 Red - Specialty interface activity (PFCS, GM or FORD)
LED10 Red - Techmotive API activity
LED11 Red - (Internal) X-bus activity
LED12 Red - Future

Options SW2
Switch #1 - Force CCM into FLASH mode
Switch #2,3,4
Sw #2
Sw #3
Sw #4
0
0
0
1
0
0
0
1
0
1
1
0
0
0
1
1
0
1
0
1
1
1
1
1

Special Forced Comm. protocol

No Forced protocol (Console can change protocol)
Enable Chrysler PFCS Protocol
Enable GM Ethernet Protocol
Enable FORD Ethernet Protocol
Reserved
Reserved
Reserved
No Forced protocol (Console cannot change protocol)

Switch #7 & 8 - Sets internal CAN bus baud rate (Set for 500k default.see table)
Sw #7
0
1
0
1

Sw #8
0
0
1
1

CAN baud rate

125k
250k
500k *
20k

____________________________________________________________________________________________
Page 40
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

CCM FIELD UPDATES

The CCM may require software updates in the field. CP Techmotives Winflash utility should work as
it does normally with the existing TCM product.
When the CCM PLUS is used, the RS-232 port that is used for VS-detachable now also becomes
the FLASH port for DCM,CCM and all internal boards downstream from the CCM. Therefore, it is
not necessary to go inside the CS47XX/2700 and move cables to FLASH upgrade.
Bottom Connector board connector layout
(This version is required for CCM+ with SDLC capability.)
External SDLC (connects to CCM+ SDLC-B
CCM to TCM SDLC Connection
(connects to CCM+ SDLC-A
(RS-232) COM2: connects to CCM+ Com0
Note that COM2: might be the upper or lower connector,
depending on the assembly.

Thes jumpers must be open so that the External RS-232

does not go to the TCM when a CCM+ is present, etc.

EXTERNAL SDLC Networking on CS4700s Equipped

with a CCM+
CS4700s can be networked with RS485/SDLC multi-drop communications. This is true even for
units that are equipped with CCM+ for ethernet capability. (However the CS2700 equipped with the
CCM+ is NOT capable of SDLC communications.
Additionally, when the CCM+ is used in conjunction with VS3.30 or higher, the CCMs real time
clock will get time-synchronized automatically with the computer that is connected to it that is
running VS (either embedded or a detachable).
Make sure to set the proper SDLC (RS-485) address on the CCM. This is different than on CS4700s
that are not supplied with a CCM, as the SDLC (RS-485) address on these units is set on the TCMs
backplane. On CS4700s equipped with a CCM, the address of the tool control module (TCM), which
is on its own backplane, must be set to 1.

Internal (CAN-BUS) Operation

The CCM communicates to downstream devices the AIM for Fieldbus and TDM for the
keypad/display via an internal CAN bus. The Communication is based on CANBUS. When
upgrading or debugging, it is important to understand some of the characteristics of this bus.
Make sure that the CCM and all downstream devices are talking at the same baud rate. The
recommended setting is 500 kbaud (see the DIP switches on the PC boards etc.). Also be sure that a
Termination Resistor is turned-on at opposite ends of the CAN-Bus network. If the CCM has no
____________________________________________________________________________________________
September 2005
Page 41

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

downstream devices, the baud rate and the termination resistor do not matter. Typically, these will be
set properly at the factory, but this could become an issue on a field-upgrade. If the baud rates are
wrong, the devices will not communicate at all. If the baud rate is correct, but the termination is
wrong, communication may be intermittent; for example, it may appear to operate properly but
flashing downstream will not work, etc.

AIM Module (CP part# 421003-41375)

(Used in Fieldbus options)
ANYBUS card connection

(Future)

(Flash program port (Direct to PIC)

(Typically not needed)

(RED) 5Volts

(Future) 24v fuse

(24vdc in/out)
( 24vdc)

Green Flashing
AIM running

RS-232
CAN in/out
(Not used) 5vdc input

Sw.2
Sw.3
Baud
0
0
125k
1
0
250k
0
1
500k*
1
1
20k
Sw.1 = CAN Termination

____________________________________________________________________________________________
Page 42
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

TDM Module (CP part# 421000-41298)

(Used in Keypad/Display option)
24vdc LED

To LED Display backlight

(Flash port (Direct to PIC)

24vdc in/out

5v LED2
To Display
New REV. TDMs
J17 LED Y
J16 - LED G
J15 - LED R

CAN in/out

R,G,Y connector

Sw.2
Sw.3
0
0
1
0
0
1
1
1
Sw.1 = CAN

Baud
125k
250k
500k*
20k

RS-232
(Not used)

To Keypad
Blinks
if running

Key-press
CCM comm. problem

____________________________________________________________________________________________
September 2005
Page 43

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

SPECIAL APPLICATION: PFCS (Ethernet or Terminal Server)

Important note: CCM1.12 adds the ability to configure PFCS without the need to enter
nd

into the console for units with a keypad/display. The CCMs SW2 (2 dip switch) can
force PFCS to be enabled. A special menu will then be available which will permit all of the
PFCS configurations.

Setting up to Link to a PFCS Host on Ethernet

1.
2.
3.
4.
5.
6.

Type ipconfig +pfcs to enable the PFCS client in the CS47XX/2700 Controller.
Type pfcs mode ethernet to configure PFCS for Ethernet operation
Use the pfcs addr <ip addr> and pfcs port <port> to enter the PFCS server info.
See below for details in using the Barcode/Buffer or Custom Machine-ID options.
When complete be sure to use the pfcs commit command
Use the pfcs +diag command to assist in debugging

Setting up to Link to a PFCS Host on Terminal Server (RS232)

Asynch Daughter
(Attached to CCM)

Location of 25Pin-D
PFCS Terminal Server connector
1.
2.
3.
4.
5.
6.
7.

Verify the controller has the add-on Asynch Daughter board & DB25 connector on the enclosure
Connect the DB25 cable from the PFCS Terminal Server to the controller
Type ipconfig +pfcs to enable the PFCS client in the controller
Type pfcs mode terminalserver to configure the PFCS client for (RS232)
See pfcs ? for details to set one of several options (ACK timeouts, Retries & other options)
When settings are complete type commit to save the settings
You can use the pfcs start or pfcs stop command although on power up PFCS will start auto.

Using Barcodes, Buffering and Machine IDs with PFCS

In order for the avi or vin data to be included in the packets to PFCS, the Model-Number or PartID functions must be enabled with VS system settings.
NOTE:

PFCS buffering will not work unless either the avi or vin is
enabled. Also, the TCM may need to be set up for VIN history
mode with the VS system settings program (for model number
applications).

When using the +psetid, the Machine ID will be derived from the first four characters of the TCMs parameter set
name that ran the cycle. VS must be used to establish parameter set names etc.
____________________________________________________________________________________________
Page 44
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

If controller is equipped with a Keypad Display

The DIAG screen on the display will show the condition of the PFCS connection as either OK or Err.
Whether the unit has a Keypad Display or not, the console can provide more extensive diagnostics information.

PFCS Ethernet Setup example: <Debug Console>

==================================================================
>ipconfig ?
'ipconfig'
- Displays TCP/IP configuration.
'ipconfig addr <ip addr> mask <subnet mask> gateway <gateway>'
- Modifies TCP/IP configuration.
'ipconfig +api' - Enables the Techmotive API Server.
'ipconfig -api' - Disables the Techmotive API Server.
'ipconfig +ford' - Enables the Ford interface.
'ipconfig -ford' - Disables the Ford interface.
'ipconfig +gm' - Enables the GM interface.
'ipconfig -gm' - Disables the GM interface.
'ipconfig +pfcs' - Enables the PFCS interface.
'ipconfig -pfcs' - Disables the PFCS interface.
'ipconfig +vseth' - Enables the Visual Supervisor Ethernet bridge.
'ipconfig -vseth' - Disables the Visual Supervisor Ethernet bridge.
'ipconfig +vssdlc' - Enables the Visual Supervisor SDLC bridge.
'ipconfig -vssdlc' - Disables the Visual Supervisor SDLC bridge.
'ipconfig commit' - Commits IP configuration to EEPROM.

>ipconfig +pfcs
Starting PFCS Client.
Ethernet Adapter CS8900A
Physical Address : 00-05-6B-07-01-00
DHCP Enabled : No
IP Address
: 10.120.17.27
Subnet Mask : 255.255.252.0
Default Gateway : 0.0.0.0
External Interfaces Enabled:
Visual Supervisor Bridge
PFCS Client

>pfcs ?
'pfcs'
- Displays PFCS client configuration.
pfcs mode <mode> -Sets mode to Ethernet or Terminal Server
'pfcs start'
- Connect to the PFCS server.
'pfcs stop'
- Disconnect from the PFCS server.
pfcs stats'
- Display PFCS communication statistics.
'pfcs stats clear'
- Clear PFCS communication statistics.
'pfcs +diag'
- Output PFCS diagnostic data to the console.
'pfcs -diag'
- Turn off PFCS diagnostic output.
'pfcs addr <ip addr>' - Sets PFCS server IP address.
'pfcs port <port>'
- Sets PFCS server port.
'pfcs retries <n>'
- Sets Max Retries to <n> (1<=n<=10).
'pfcs ack <n>'
- Sets Ack Timeout to <n> seconds (1<=n<=10).
'pfcs keepalive <n>' - Sets Keep Alive Interval to <n> seconds (30<=n<=240)
'pfcs reconnect <n>' - Sets Reconnect Interval to <n> seconds.
'pfcs +psetid'
- Machine ID for rundowns will use PSet Name.
'pfcs -psetid'
- Machine ID for rundowns will be assigned by PFCS.
'pfcs avi'
- PFD will send AVI barcode with results.
'pfcs vin'
- PFD will send VIN barcode with results.
'pfcs nobarcode'
- PFD will not send barcode with results.
'pfcs +buffer'
- Enables buffering of rundowns.
'pfcs -buffer'
- Disables buffering of rundowns.
'commit'
- Commit PFCS settings to EEPROM storage.

>pfcs addr 10.120.16.116

[Note: This is the IP address of the PFCS host]

PFCS is enabled.
PFCS Server Address : 10.120.16.116
PFCS Server Port : 16101

____________________________________________________________________________________________
September 2005
Page 45

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

Max Retries
:3
Ack Timeout
: 5 seconds
Keep Alive Interval : 120 seconds
Reconnect Interval : 10 seconds
Machine ID assigned by PFCS.
Barcode disabled.
Result buffering disabled.

>pfcs port 16101

PFCS is enabled.
PFCS Server Address : 10.120.16.116
PFCS Server Port : 16101
Max Retries
:3
Ack Timeout
: 5 seconds
Keep Alive Interval : 120 seconds
Reconnect Interval : 10 seconds
Machine ID assigned by PFCS.
Barcode disabled.
Result buffering disabled.

[Enter any other applicable pfcs commands (MachID,Buffer options etc.]

>pfcs commit
Writing changes to EEPROM...
*** WARNING! DON'T POWER DOWN UNTIL EEPROM WRITE IS DONE!
>EE
Initalizing CCM
Loading FPGA...
Initalizing EEPROM Data...
Initializing System Time: Wed Aug 20 13:43:22 2003
Starting TCP/IP.
IP Address 10.120.17.27
Starting VS Bridge on port 5000.
Initializing RS-232 Communication.
Initializing SDLC Communicaton.
System is coming up...
*********************************************************
Communication Control Module CCM Debugging Console V1.01
Copyright 2003 CP-GSE Techmotive Tool
*********************************************************
Hello.

>pfcs +diag

[Use this command to view PFCS running diagnostics]

____________________________________________________________________________________________
Page 46
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

SPECIAL APPLICATION: GM

(General Assembly Engineering)

The CS47XX/2700 Controller has an Ethernet interface that complies with the latest specification for
sending data to the GM server. It also has a DeviceNet interface that complies with the GM
specification.
Note that it with Keypad/Display units that much of the below configurations can be done by setting
the CCM SW2 DipSwitch #3 to force the GM Driver to be enabled and using the keypad to make the
appropriate setups.
Here are the general setup instructions (If using the console):
1. Enable the GM Ethernet interface via the RS-232 console {ipconfig +gm}
2. Enter the GM Server IP address via the RS-232 console

NOTE:

?
3.
4.
5.

The CS4700 Controller is considered the slave in this

configuration.

Set up the appropriate GM I/O fieldbus mapping via the RS-232 console. Refer to the Fieldbus
Section (GM4 or GM8 I/O) {aim setmode gm4}
Set defaults using either the RS-232 console or the keypad. You should select one of the
fieldbus defaults to block OPC.
Set up the fastening strategy and parameter limits using the keypad or VS.
a. If GM (PVIs) are being used, the Model# Barcode must be enabled and the minimum length
must be set to 1 in the VsSetup-barcode setup tab-mask.
b. In order for the GM host to be able to see the PVI, make sure the VIN-History mode for
Model# barcodes is enabled. This is done in VsSystemSettings.

IMPORTANT GM Information
The GM specification requires that certain algorithms and setpoints be used for compliance.
In general, when setting the defaults through the keypad, these are appropriately set except for
application customization of specific setpoints.
GM has adopted a general standard which gives special meanings to the lights presented to the
operator.
LIGHT

GENERAL PROCEDURE
(Conditions applicable to torque control)

Yellow

The fastener can be rerun

TORQUE-LOW (unless ANGLE-HIGH)
The fastener must be backed out and replaced.
ANGLE-HIGH failure (or)
REMOVE-TORQUE-LIMIT exceeded
The fastener must be backed but can be re-run
Failure conditions that do not show above.

Red

Red & Yellow

____________________________________________________________________________________________
September 2005
Page 47

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

In order to meet this specification and the required light patterns for all of the various conditions (not
shown here) here are some rules to setting up the controller:
1.

The GM Red/Yellow/Green lights must be mapped instead of the standard R/Y/G lights
(This should already be done if Defaults were loaded after the box was set to GM mode)

2.

The REHIT algorithm can be enabled if it is desired for the application. This is a special
monitor function to detect if an operator is trying to tighten an already tight fastener.
NOTE:

The REHIT Stop Torque parameter should be above the

Threshold (ZDR) limit and if you are using Torque Control, it
should be below the Target Torque.

3.

The REMOVE-TORQUE-LIMIT (on the pset Torque Monitor tab) must be set higher
than the Torque-High limit.

4.

In order to guarantee the I/O timing over DeviceNet, a Minimum Time between cycles of a half
second should be entered (keypad defaults should set this already etc.).

5.

Slip Detect (on the pset Torque/Angle Control tab) can be enabled, if desired. This algorithm
is intended to stop the tool if the torque drops off significantly (for example, due to a broken bolt
or because a socket has slipped off, etc.)
For this Slip-Detect to function per the GM Specification, the controllers Control Ref Torque
must be equal to ZDR (or Threshold torque).

In most instances, VS should not be needed for the GM-required setup on units with a keypad/display;
Rather, select the GM Mode and use the set defaults as instructed above. If a VS-embedded
controller/PC is connected, be sure to select VIN History (Model#) mode as the GM host requires it.
The CS47XX controller for GM is special in that it must also be fitted with the appropriate GM
specified I/O connectors. Additionally, special provisions within the enclosure provide an isolated
24vdc supply for the DeviceNet function.

____________________________________________________________________________________________
Page 48
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

Console/keypad based Default selections: 3* - Typical

Selection
DEFAULT#
1
2
3*
4

Parameter Set Select

Tool Running control

Fieldbus
Fieldbus
DCM physical I/O
Keypad

Fieldbus
Operator switches on tool
Operator switches on tool
Operator switches on tool

Default Selection (DCM inputs) table (GM MODE):

DCM Input
Input#1
Input#2
Input#3
Input#4
Input#5
Input#6
Input#7
Input#8
Tool Cycle trig.
Tool Direction Sw
Tool Aux. Sw.

DEFAULT#1

Release One Job

Bypass

DEFAULT#2

DEFAULT#3

DEFAULT#4

Cycle-on
Release One Job
Forward
Cycle Enable
Bypass
Cycle Enable
Forward

Pset select 0
Pset select 1
Pset select 2
Cycle-on
Release One Job
Forward
Cycle Enable
Bypass
Cycle Enable
Forward

Cycle-on
Release One Job
Forward
Cycle Enable
Bypass
Cycle Enable
Forward

Default Selection (DCM outputs) Table (GM MODE):

DCM Output

DEFAULT#1,2,3 or 4

Output#1
Output#2
Output#3
Output#4
Output#5
Output#6
Output#7
Output#8
Tool YELLOW
Tool GREEN
Tool RED

Light GM Green
Pass-thru STACK Light - Yellow
Light GM Red
Light GM Yellow
Pass-thru STACK Light - Green
Pass-thru STACK Light - Red
In-cycle
Pass-thru
GM STACK Alarm
Light GM Yellow
Light GM Green
Light GM Red

____________________________________________________________________________________________
September 2005
Page 49

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

CONNECTOR PIN DEFINITIONS

5 Pin-DIN male Device-Net Connector
Turck #RSF 571-2M/S630
PIN
1
2
3
4
5

Description
Shield
No connection within CS4100 (24v field)
Isolated Common (Device-Net Ground )
CAN_H
CAN_L

Optional Bypass/Release
Pendant Connector

Optional Stack-Light
Connector

4-pin Micro Female Connector

Crouse-Hinds #5000118-4

5-pin Micro Female Connector

Crouse-Hinds #5000129-332

Field mate: Turck # FKFD4.4-X

Field mate: Turck#FKB5-X

PIN

1
2
3
4

Description
+24vdc
Bypass
(DI8)
N/C
Release One Job (DI5)

PIN
1
2
3
4
5

Description
Pass-thru GM Green
Pass-thru GM Yellow
0 volt - Common
Pass-thru GM Red
Pass-thru GM Stack Alarm

(DO5)
(DO2)
(DO6)
(DO8)

Optional Remote-Handle

Optional Remote-Light Box

10-pin Bendix#PT02A-12-105
Field mate: PT06A-12-10P (SR)

Bendix#PT02A-14-19S
Field mate: PT06A-14-19P (SR)

PIN
A
B
C
D
E
F
G
H
J
K

Description
24vdc from CS4100
Cycle-on
(DI4)
Cycle enable
(DI7)
In-Cycle
(DO7)
Pset select 0
(DI1)
Pset select 1
(DI2)
Pset select 2
(DI3)
Forward
(DI6)
Common
Shield

PIN
A
B
C
U
D
V

Description
Good (remapped stack alarm**)
(DO8)
GM Red
(DO3)
GM Yellow
(DO4)
+24vdc
Common
GM Green (Flash EPR) (DO1)

Note: On the single channel CS4100,

the remaining pins are unused.
**DO8 must be remapped with VS to be GOOD
(non-flashing).
EPR Error Proofing Ready functionflashes
when READY.

____________________________________________________________________________________________
Page 50
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

SPECIAL APPLICATION: FORD

The CS47XX has an Ethernet interface compliant with Ford specification PF3000.The basic steps to
setup a CS47XX controller for Ford follows:
Note that the CCM DipSwitch SW2 Swtich# 2 & 3 can force the FORD drivers without the console.
Also, units with the keypad/display can be used to setup most/all of the required settings.
1.
2.

Enable the FORD Ethernet interface via the RS-232 console.

Determine what IP address this controller must have, and enter it via the RS-232 console.
NOTE:

?
3

The CS4700 Controller is considered the Ethernet server in

this configuration.

Either set defaults from the RS-232 console or via the keypad, or use the VS program to set up
the appropriate I/O sources. This must be done to provide proper functionality (Tool runs from
switches on tool, where are the psets selected etc.)
Set up the fastening strategy and setpoints either from the keypad or Visual Supervisor.
NOTE:

It may be necessary to assign a batch count that corresponds

with the pset number. (Example: Pset#1 has a batch of 1,
Pset#2 has a batch of 2, etc.)

Example of a Ford based Network:

Operator HMI (change psets/batch count etc.)

CEC box

CS4700

Ford Server

____________________________________________________________________________________________
September 2005
Page 51

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

SPECIAL APPLICATION: Screwdrivers

When setting up the CS2700 Controller for use with an SD25 Series screwdriver the VS Default
settings are used to map the I/O to fit typical screwdriver applications. A typical function times the
operation of the headlights to the Cycle Start mode of operation.
However, when it is set up for typical operation, the CS2700 Controller does not comply with GM
specifications. The I/O configuration mandated by GM Assembly does not match those that are
typically mapped for convenient screwdriver operation.
Here are the general setup instructions:
1. Enable the specific Ethernet interface via the RS-232 console (if applicable).
2. Set up the appropriate I/O fieldbus mapping via the RS-232 console.
Set defaults from the RS-232 console or via the keypad, OR VS to set up the appropriate I/O
sources. This must be done to provide the proper functionality (The tool runs from the switches
on tool, where are the psets selected etc.)
3. Set up the fastening strategy and setpoints either from the keypad or VS.
At the present time, CS2700 Screwdriver Controllers that have Ethernet capability do NOT support
SDLC networking (via the RS-485 port).

SPECIAL APPLICATION: Tubenut and Offset Tools

With the current revision of software, these applications may require VS to modify the I/O to operate
the Tool in the manner desired. Setting Defaults from the Keypad/Display or CCM console may
not provide the Final desired configuration for these tool types.

Tubenut and Offset Nutrunners

You may need to uncheck the left-hand tightening option from keypad-based default settings

____________________________________________________________________________________________
Page 52
39-30-43083

_____________________________________________________CS4100/2100 Controllers Technical Reference

General Troubleshooting (Basic)

CONTROLLER TYPE

Symptom

Possible Solution

CS4700/2700 Controller
(Any configuration)

Tool Wont run

1. No tool detected scrolling message

* Suspect tool/ITI board
* Suspect TCM
2. Invalid Parameters scrolling message
* Hook up VS (run VsSetup & Correct)
3. No LIGHTS on TCM
* Verify circuit breaker/GFCI
* If TCM is Rev.K or higher, the fuse
on the TCM servo may be blown.
(Note: Prior to Rev. K, the display
might still light even if the Servo
fuse is blown).
4. TCM looks OK with READY light
* Suspect INPUTs mapping (Use VsSetup)
* If external cycle-on, suspect 24vdc source
* If unit has Ethernet capability, improper
Defaults may have been selected blocking
INPUT source.

CS2700 with Ethernet capability

(Screwdriver controller)

Wont communicate to VS on SDLC port

If CS2700 is configured for Ethernet capability,

the SDLC port WILL NOT work. See the
section Connecting to Visual Supervisor in this
manual.

Any controller with Fieldbus

(DeviceNet, Profibus etc.)

Controller wont respond to INPUT

commands via Fieldbus (Cycle Enable,
Cycle Start etc.)

It is critical to have selected the correct default

which will allow INPUTS to enter in via Fieldbus.
See this manual Determining Input Sources
and selecting Default#1 (Via Keypad or
Console) should then allow inputs from Filedbus
Possibly need to change the ENDIAN (Byte
Order) setting.

Data is ok except for FLOAT and

INTEGER values

____________________________________________________________________________________________
September 2005
Page 53

xxxxxxxxxx

CS2700/4700 Controllers Technical Reference_________________________________________

General Block Diagram (Data/History/Barcodes)

____________________________________________________________________________________________
Page 54
39-30-43083

www.cp.com

Please find your local contact at: www.cp.com

U.S. English
Printed in USA
Copyright 2005
CP techmotive, Novi, MI, USA