Scribd
Upload
72 views1 page

PG 0009

The document describes the LED display on an option component. It has four LEDs that indicate power status, errors, communication status, and PROFIBUS errors. The LED states after startup are described in a table, including normal operation and possible issues. Another table shows the expected LED patterns for different situations, such as no power, connection errors, waiting for communication, and communication errors. The document provides troubleshooting tips for resolving potential issues indicated by the LED patterns.

Uploaded by

Munteanu Simona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
72 views1 page

PG 0009

The document describes the LED display on an option component. It has four LEDs that indicate power status, errors, communication status, and PROFIBUS errors. The LED states after startup are described in a table, including normal operation and possible issues. Another table shows the expected LED patterns for different situations, such as no power, connection errors, waiting for communication, and communication errors. The document provides troubleshooting tips for resolving potential issues indicated by the LED patterns.

Uploaded by

Munteanu Simona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

4 Option Components

Option LED Display


The option has four bicolor, red/green LEDs to relay information about power, communication status, and errors. The
operational states of the LEDs after completion of the power-up diagnostic process are described in Table 5. Wait at least
2 seconds for the power-up diagnostic process to complete before verifying the states of the LEDs.
Table 4 Option LED States
Display
Color
Status

LED

RUN
(Power)

Operating Status

ON

Power supply ON

OFF

Power supply OFF

ON

Option error
Drive connection
error
Normal operation
Communication
connected

Green

ERR
(Option Error)

Red

Flashing
OFF

COMM
(Communication
Status)

ON
Green
OFF

No data exchange

ON
BF
(PROFIBUS-DP
Error)

Red

Flashing
OFF

Waiting for
communication
procedure setting
Communication
setting error
Normal operation

Remarks
Power is supplied to the option, and the option hardware self-diagnostics check
is complete.
The drive has no power supply.
Option and drive are not connected properly and/or no power is supplied to
the option.
An internal, self-diagnostic error occurred in the option.
Self-diagnostic error occurred in the option.
Connection error between option and drive. This includes node address setting
errors to parameter F6-30 on the drive side.
Drive and option are properly connected.
Normal send/receive between the option and the PROFIBUS-DP master.
There is a problem establishing communication between the option and the
PROFIBUS-DP master.
Communication-related parameters are in the process of being set or initialized
by the PROFIBUS-DP master.
Communication parameter error from PROFIBUS-DP master.
LED shuts off when the PROFIBUS-DP master is finished setting
communication-related parameters.

Table 5 LED Operation After Power-up Diagnostic


LED
Communication
Status
RUN ERR COMM BF

No power

Possible Cause

Solution

Drive has no power.

Check all wiring to the drive, then turn on the power.

Option is not properly connected to the


drive or is not receiving enough power.

Shut off the drive and make sure the option is


connected properly. Turn the power back on.

Checking
connection with

the drive
Waiting for data
from the master

Option selfdiagnostics error

The option is damaged.

Problem connecting
to the drive

Problem initializing the drive and the


option.
Incorrect node address.

Waiting for data


from the master
device

Incorrect data or
option time out
waiting for data

Sending or
receiving data

Option is reading the node address or


parameter configuration.
Waiting for initial input data from
master device.

Cycle power to the drive. If the LED status does not


change, replace the option.

Cycle power to the drive. If the LED status does


not change, replace the option.
Check the node address setting in the drive (F6-10)
Check master network settings.
Make sure the master device is operating normally.
Waiting for data from the master device. Check terminal resistance settings on the data line.
Check for problems with the data line and
(Set_Parm_Message or
Chk_Cfg_Message)
connector.
Check if the data line is connected properly to
communication connector CN5.
The communication settings in the
master are set incorrectly.

Check the communication settings in the master.

{: On / : Flashing / : Off
YASKAWA ELECTRIC SIEP C730600 42B 1000-Series Option SI-P3 Technical Manual

You might also like