McCarthy P L, Internal AMC Paper

Pit Optimisation
By P L McCarthy 1

Introduction
For any deposit which can be fully or partially mined using
open pit methods, there is one pit design which will maximise
the NPV of the project at the designed mining rate. Several
methods are available to optimise the design of the open pit to
approach this ideal. It should be noted that all optimisation
techniques produce a theoretical pit limit design which then
must be subject to detailed design. The incorporation of catch
benches, working face angles and/or roads leads to a practical
mining design which may not provide the idealised NPV
produced by the optimisation method. However, with careful
planning, the variation from optimum will not be substantial.

Manual Methods
To perform a manual design it is important to understand the
difference between the overall stripping ratio for the pit and the
incremental stripping ratio for the last bench or block of ore. In
optimising the pit, the overall stripping ratio is irrelevant and is
simply a property of the final pit design. The incremental
stripping ratio is the ratio of the volume or tonnage of waste
which must be moved to access the next increment of ore to the
mass of ore that will be accessed.
Expected costs and revenues are then used to calculate a
minimum acceptable stripping ratio for the last increment. The
pit design is then produced by drawing increasingly large pit
shells on cross section such that the last increment has a strip
ratio equal to the design minimum. This is a very labour
intensive approach and can only ever approximate the optimal
pit. The design must be done on a large number of cross
sections and is still inaccurate because it treats the problems in
only two dimensions. In cases of highly variable grade the
problem becomes extremely complex.

The Floating Cone Method

The floating cone method was developed at Kennecott Copper
Corporation during the early 1960s. The method requires a
three dimensional computerised block model of the mineral
deposit
Figure 1. The projected ultimate pit limits are developed by
using the moving cone technique. The technique generates a
series of interlocking frustum shaped removal increments.
Figures 2 and 3 show a typical removal increment, as well as a
series of interlocking increments.

1.

MAusIMM, CPMin, Managing Director, Australian Mining

Consultants Pty Ltd, 19/114 William Street, Melbourne Vic 3000.
E-mail: [email protected]

The economic model is generated by determining the projected

value of each block in the mineralisation model. The
relationships between grades, metallurgy, stripping ratio, costs,
etc., involved in the pit limit analysis are dynamic throughout
the pit design. Geotechnical studies are required to design the
final pit wall slope angles. The pit is usually divided into a
number of zones in plan. The slab zones are defined by vertical
planes extending radially from the projected centre of the pit
design bottom. A horizontal plane may be placed within the
sectors to modify the slopes due to the water table or other
elevation controlled characteristics.

The optimisation process consists of:

Data input and conversion
Economic block evaluation
Removal increment selection
Mining simulation (which generates pit limit designs)
Data output including level by level summaries and plots.
The floating cone technique is generally considered to be
inferior to the Lerchs Grossmann method. Floating cone
methods were developed first and are easier to program at a
machine level but can give erratic results. It is necessary to do a
number of runs with variable input parameters in order to test
the model.

The Lerchs Grossmann Method

This was a mathematical technique which was unusable in
practice until a practical optimisation programme called Whittle
Three-D was developed by Jeff Whittle of Whittle
Programming Pty Ltd in the mid 1980s. The Whittle
programme and a more recent development called Four-D are
now in worldwide use and are the best available pit
optimisation programmes.

The following discussion is based on notes prepared

by Jeff Whittle.
Consider the idealised situation shown in the east-west section
in Figure 4 where there is a flat topography and a rectangular
orebody of constant grade. We will assume that the orebody has
a long north-south strike so that the effects of the ends of the pit
are small and we can design on a sectional basis. The horizontal
lines represent bench levels and there are eight possible pit
outlines.

Pit Optimisation

Figure 1 Three dimensional representation of an ore body.

Figure 2 Typical Removal Increment

AMC Reference Library www.ausmin.com.au

Pit Optimisation

Figure 3 - Defining pit limits of a hypothetical ore body with a series of removal increments

Figure 4

AMC Reference Library www.ausmin.com.au

Pit Optimisation

If each bench contains 500 tonnes of ore and each diamond

shaped block of waste represents 100 tonnes, the totals in Table
1 apply.

Table 1 Tonnages and values for the possible pit

outlines
7

Ore

500 1,000 1,500 2,000 2,500 3,000 3,500

4,000

Waste

100

6,400

Total

600 1,400 2,400 3,600 5,000 6,600 8,400 10,400

Value

900 1,600 2,100 2,400 2,500 2,400 2,100

Pit

400

900 1,600 2,500 3,600 4,900

1,600

Table 2 Discounted cash flows for the pits using flat

or incremental mining, and with milling and mining
capacity limited
Pit
Flat Mill
500
Incr. Mill
Flat Mine
1,000
Incr. Mine
1,000

900 1,530 1,917 2,085 2,057 1,851 1,486 978

900 1,530 1,935 2,154 2,220 2,161 2,002 1,763
900 1,520 1,868 2,011 1,956 1,552 1,049 499
900 1,520 1,898 2,068 2,105 1,993 1,790 1,540

For each mining sequence two cases are considered:

If ore is worth $2.00 per tonne after all ore mining and
processing costs have been paid, and if waste costs $1.00 per
tonne to remove, then we have the total values shown in Table
1 in today's dollars. If we plot pit value against pit tonnage we
get the graph shown in Figure 5. Whether pit 5 is in fact the
optimum pit depends on the mining sequence and on the mining
and processing capacities.

Where processing is limited to 500 tonnes per year,

the total mining capacity is unlimited.

Where processing capacity is unlimited, but the

mining capacity is set at 1,000 tonnes per year, based
on the cashflows and a discount rate of 10% per
annum.

Figure 5

The value of the optimal pit is underlined in each case

and two things are clear.

Unless incremental mining costs are very much

higher than flat mining costs, incremental mining will
make more money for us than flat mining. From the
cashflow point of view, incremental mining is
optimal.

If we mine a pit in a sub-optimal sequence (i.e. by flat

mining) the optimal pit gets smaller.

If the mining and processing capacities are such that we can

mine the whole pit out within a few months, then the sequence
in which we mine has little effect on the total cashflow, and pit
5 is still the optimum pit.
On the other hand, if the mining and ore processing capacity are
limited and the mine is going to take five years to complete,
then the mining sequence can not only affect the total cashflow,
it can affect the size of the optimal pit. If we mine the pit in
strict bench order, (i.e. we complete the mining of each bench
before starting the next), then in the early years we will be
mining waste at the edge of the pit and paying the cost in
today's dollars. However, the ore that this eventually releases
will not be reached until four or five years later, and because of
discounting, its value will be much less than is required to pay
for the earlier waste removal. In short we would have been
better off not mining the edge waste in the first place, so the
optimal pit is no longer correct. On the other hand, if we first
mine pit 1 and then incrementally mine out pits 2, 3, 4, etc. the
effect is much smaller.
To illustrate this, Table 2 shows the results of two idealised
mining sequences with each of two different tonnage limits for
each of the eight pits. These use flat mining, where each bench
is completed before the next is started and also incremental
mining, where pit 1 is mined out before pushing back to pit 2
etc.

AMC Reference Library www.ausmin.com.au

Note that any practical mining sequence for a particular pit

outline will produce a value, which is between the two
extremes. Unless you mine waste and leave exposed ore
untouched, it is not possible to produce a worse value than that
produced by flat mining, and it is not possible to produce a
higher value than that produced by incremental mining.
Optimisation works from a block value model and true threedimensional optimisation finds the optimum list of blocks to
mine. Thus block size may be thought to be important. Four
different block sizes are relevant in pit design.
1.

There is the block size used for orebody modelling. It

has to be small enough to outline the orebody clearly.
This can lead to block models consisting of millions
of blocks. Some systems reduce this number by
allowing subdivision of blocks as required. Some
systems use outlines directly rather than blocks.

2.

There is a block size which represents the minimum

volume which can be selectively mined. This is the
size at which block values should be worked out.

3.

There is a block size which is suitable for pit

optimisation for design. This is a compromise
between the full detail of the orebody model and the
production of a realistic computation time for the
optimisation process. The shape of the curve given in
Figure 5 suggests that providing you get reasonably
close to the optimal pit volume, you will get very
4

Pit Optimisation

close to the optimum value. Thus larger blocks can be

used in the optimisation process. Typically, 100,000
blocks is sufficient for design work. More blocks may
be used for larger pits with more complex geology or
when computing power and speed is not a limitation.
4.

There is a block size which is suitable for doing

sensitivity studies using optimisation. That is, a
coarser block model may be appropriate if the speed
of optimisation is limited by the processing power.
For example, it may be necessary to run several
optimisation runs during the working day rather than
run one final optimisation overnight. However, with
modern computers and particularly using 4D, the
optimisation process is very fast or is carried out as
part of the primary optimisation. Thus it is less
common these days to produce a separate
optimisation model.

It should be noted that apart from any obvious incremental

costs, any overhead expense, which would stop if the mining
was stopped, must be included in the cost calculations.
This is because, when an optimisation programme is deciding
whether to mine a block it is, in effect, deciding to extend the
life of the mine, and must therefore take account of the costs
involved in that.
If overheads are not included in the costs, the programme will
probably design a pit, which will not support the overheads in
its final years.
Overheads should be divided between mining and processing. It
can distort the pit if all overheads are added entirely to
processing costs or entirely to mining costs.

The Steps Involved in Designing a Pit

To design a pit you should carry out the following steps:

evaluate each pit subject to your mining sequence and

select the one with the highest value.

Do the detailed design using the highest valued pit as

your guide. Note that only one detailed design will be
done and that that is easy because the shape and size
of the pit has been established.

Detailed Design
Pit optimisation produces a jagged outline from the block
model. This outline must be smooth and all roads and safety
beams must be put in. To smooth the outline by hand, you
merely draw a smooth curve approximately through the mid
points of the block edges. If you are using computer aided
design, you contour the surface defined by the centre of the
base of the lowest block in each column.
By doing this, tonnage is added and subtracted alternately along
the outline in almost identical quantities. If a particular part of
the outline is entirely in ore, or entirely in waste, then these
balanced additions and subtractions have no effect whatever on
the value of the pit. Losses in one part of the pit are likely to be
gained in another.
Provided the optimal blockout line has been generate with
average required slopes, then similar balanced additions and
subtractions occur when all roads and safety berms are
incorporated into the pitwalls.
It should be noted that optimal pit outlines are very robust in
the face of dimensional change. Refer to the curve linking pit
values and tonnage in Figure 6. If detailed design starts from
point A, which is not optimal, then small changes to the design
can make significant changes to the value of the pit.
Historically this was the case and pit designers spent days or
weeks assessing the effects of detailed changes to designs.
With an optimal outline, the curve is approximately horizontal
at point B and small changes have almost no effect on the value
of the pit.

Develop a model of the orebody, the waste and the

air.

Produce a block model with blocks no smaller than

the selective mining unit.

Carry out the sensitivity work for a range of

economic conditions. This work will sort out the
general scale of mining and hence the costing details.
Also decide approximately where the roads are to go
and adjust the slopes in those places to reflect the
average slope required.

Having fixed the economic parameters, generate a

value model.

If necessary, reblock the model to optimise the

number of blocks.

Carry out the optimisation using the required slopes.

Calculation of Revenue

If you think that the mining sequence you propose

will significantly effect the size of the optimal pit,
then repeat steps 4, 5 and 6 with progressive
reductions in product price so as to produce a set of
nested pits. Two or three should be sufficient. Then

In a simple single product case the revenue can easily be

calculated from the metal price and the metallurgical recovery.

AMC Reference Library www.ausmin.com.au

Provided you follow the spirit of the optimal outline without

tidying it up too much, the resulting design will remain very
close to optimal.

Figure 6

E.g.: Gold Price $370/oz Metallurgical Recovery 95%

Pit Optimisation

For a 100 t block with a grade of 2.5 g/t Au the revenue is given
by:
Grade x Metal Price x Recovery
2.5 x 370/31.1035 (grams per ounce) x 0.95 x 100 = $2,825
In a more complex case where there may be several products
with different treatment routes the revenue calculation becomes
more complex. In these cases it is often easier to work in
equivalent grades, that is calculate the grade of one element
which would yield the same revenue.

Revenue = Equivalent Cu grade x Cu recovery x Net

commodity price
= 0.43457 x 0.766 x 1338.39
= $445.524
We could of course have calculated the revenue for each
product separately and totalled them, however where there are
many calculations to be performed the use of equivalent grades
simplifies calculation. However, it is essential to thoroughly
check and frequently recheck the formulae, because relativities
change and are very often overlooked.

Take the example of a deposit with four products, Cu, Au, Ag

and S. For each commodity we know the market price we will
receive and the costs incurred in extracting that product
measured in $/unit of product. We can therefore calculate a net
commodity price:

Summary

From the standardised net commodity price and the

metallurgical recovery we can calculate any equivalence factor
to convert the grade of any product to an equivalent copper
grade.

Pit optimisation provides us with a tool to calculate the ultimate

pit which will generate the greatest operating surplus. It also
allows us to conduct "what if" investigations quickly and
efficiently.

Equivalence Factor = Product Price x Product Recovery

However these are complicated tools and must be treated with

caution, the old adage "Garbage in, Garbage out" was never
truer. When conducting optimisations it is important to
maintain a practical footing and not lose sight of what can be
achieved.

Using these equivalence factors the Copper Equivalent grade of

a block can be calculated.

The concept of equivalent grades is also useful in considering

cut-off grades in a polymetallic deposit.

The commodities in this block have a combined value

equivalent to a block only containing copper but at a grade of
0.43457%.

Having determined an optimal pit outline a design should

always be prepared to ensure that that shell can be mined.

We can now calculate a revenue from this equivalent copper

grade.

Optimisers also tend to be "computer resource hungry" They

can be run on 486's upwards but tend to create very large arrays
and so large amounts of disk space are required.

AMC Reference Library www.ausmin.com.au