B9000FXS
60 to 300 kVA
Three-phase UPS
Industrial Power Solutions
Performance and reliability for any kind of critical applications
FleXible and Smart
B9000FXS combines management
of THD and power factor, low cost of ownership
and power protection in a highly reliable solution
guaranteed by the most advanced technology.
INFORMATION AND
COMMUNICATION TECHNOLOGY
Data centers
Server farms
Communication rooms
Broadcast
Networking
CRITICAL ELECTRICAL ENGINEERING
Industrial controls
Manufacturing machinery
Process equipment
Transportation
Building automation
LOW THDi and POWER FACTOR PERFORMANCE ENHANCE
COMPATIBILITY with INPUT MAINS and GENERATORS
The BORRI B9000FXS model UPS uses a completely new
IGBT input rectifier design, encompassing an advanced PFC (Power Factor Control) which is capable
of keeping input current THDi (Total Harmonic
Distortion) at a level of less than 3% and the input
power factor within 1% of unity, even when only
small loads are applied.
The key benefits are that the UPS is therefore compatible with the upstream source, the mains or any kind
of generator and the transfer of power between source
and load is more efficient. This results in a saving in terms of scale of
sources, cables and protective devices.
HIGH EFFICIENCY REDUCES OVERALL COST
of OWNERSHIP
The B9000FXS has a new SOL (Smart On-Line) function which enables
a total operating efficiency of between 95% and 98%. This mode
referred to as Intelligent ECO mode significantly reduces the utility costs associated with operating a device of this type. Moreover,
this increase in efficiency results in the production of less waste heat,
minimising cooling/airconditioning costs. This
represents a double saving to the energy conscious user.
The SOL function uses
continual monitoring
techniques to review the
input characteristics of
the supply. This means
that if the supply line
drops or fluctuates outside of acceptable conditions the UPS uses the internal inverter to support
the load. This is achieved
through a fast, fully static
transition from VFD to VFI
mode.
DOUBLE CONVERSION TOPOLOGY OFFERS DOUBLE
PROTECTION for EVERY APPLICATION
The VFI Online double conversion topology implemented in this equipment offers built in inverter galvanic protection completely isolating
the output power from all the input power anomalies, delivering fully
conditioned pure sine-wave output.
Because of the technology and topology used, no additional losses
are generated to get low input harmonics or input/output galvanic
isolation.
The B9000FXS unit is designed to provide excellent output voltages
suited to very demanding applications with either 100% step load,
unbalanced, non-linear or modern IT loads.
It also provides exceptional performance: with a power factor of up to
0.9 (lagging or leading), there is no requirement to de-rate the unit.
TRIPLE INTELLIGENCE: FleXible and Smart
If the application requires extremely flexible and reliable UPS protection, the B9000FXS is ideal. It delivers advanced features based on
state-of-the- art total digital control. This control incorporates dual
DSP (Digital Signal Processing) and C (Micro controller) technologies.
The system design ensures that auxiliary power supplies and processors are no longer single points of failure which could compromise
the availability of clean power to the load.
The B9000FXS is designed to overcome the limitations imposed by
other, older, designs. With its distributed control architecture, the
B9000FXS will always have a UPS circuit protecting the load; furthermore, the status of most critical components is constantly monitored,
allowing predictive maintenance and avoiding unexpected breakdowns.
B9000FXS working state can be easily monitored by any Building Management System and via LAN/WAN.
ACCURATE BATTERY MANAGEMENT
Batteries are electro-chemical devices, which store charge chemically; as such their performance degrades with time. The B9000FXS
performs ABM (Accurate Battery Management) according to battery
manufacturer requirements.
Following a UI characteristic curve, the charger charges at a constant
current appropriate for the battery type used, preventing detrimental
excess charging. In addition to the float voltage level, boost charge
can be set, optimising the recharge time when there is the possibility
of consecutive power outages within a short period.
ABM also reduces the residual ripple current (one of the causes of premature battery wear), as well as protecting the battery from damaging deep discharges.
Automatic battery temperature compensation charge voltage may be
implemented, charging the battery more appropriately and increasing battery life.
By means of the DCM (Dynamic Charging Mode) very long battery autonomies can be achieved without increasing total charge time. This
is achieved through the implementation of an intelligent increase in
maximum battery charge current when the maximum inverter power
is not being drawn by the load.
An integrated periodical battery testing function tests and monitors
battery health, providing advanced warning to guide the application
of preventive maintenance.
PARALLEL SYSTEMS for REDUNDANCY or
CAPACITY INCREASING with HOT SWAP MODULARITY
The B9000FXS UPS solution offers parallel options in both redundancy
and capacity modes, providing the possibility for both extra system
resilience and increased capacity.
The parallel control circuitry associated with these units is fully digital
and acts on both active and reactive power on each of the three output phases. This allows accurate load current sharing among the UPS
units even during transient conditions.
Parallel control is distributed between all units and communication
is achieved through the use of a CAN BUS connection loop. This has
the effect of producing a highly reliable system with no single points
of failure.
Intelligent design of the system connections allow for easy installation
and easy future upgrades, this allows for upgrading the field without
difficulty.
In the modular arrangement, units can be added or removed hot
without load disturbances or the need to switch to bypass.
Smart Parallel functions facilitate the automatic switching off of units
where the total power requirements of the load is provided by fewer than the total number of UPS units attached. . This is commonly
known as load based shutdown and maximises the efficiency of the
complete system by keeping the load on each module at an optimum
level.
Two independent paralleled systems can be synchronized (Sync Control) in order to feed downstream STS for seamless transfers.
Bypass
Mains
Parallel ...n
Load
EASY INSTALLATION, OPERATION and MAINTENANCE
The B9000FXS can be installed up close to walls or other cabinets as
cooling air is expelled through vents on the top of the unit.
This new design gives the user a significant saving in floor utilisation. This
makes the B9000FXS an ideal solution where space is at a premium.
Despite this modern compact design, all critical components are accessible from the front of the unit; this improves accessibility to allow
regular maintenance and reducing Mean Time to Repair (MTTR).
Removable blowers
USER INTERFACE and ACCESSORIES
User-friendly Interface
COMUNICATION
RS232 serial port
USB port
Remore EPO
External Manual
Bypass status
Battery Switch
status
Diesel Mode
Front access
OPTIONAL
Web/SNMP
ModBus
Relays
Modem
Remote panel
OPTIONS
Parallel capacity/redundancy
Sync control for dual feed systems
Isolation transformer
External bypass
External battery cabinets
Battery switch box
Battery thermal probe
Transformers/ autotransformers
for voltage adaption
Top cable entry
Monitoring, managing
and shutdown software
B9000FXS
60 to 300 kVA
Three-phase UPS
Performance and reliability for any kind of critical applications
RATING
Capacity (kVA)
60KVA
80KVA
100 KVA
125 KVA
160 KVA
200 KVA
250 KVA
300 KVA
60
80
100
125
160
200
250
300
580
600
662
720
1020
1200
Dimensions WxHxD (mm)
Weight (kg)
815x825x1670
1200x860x1900
630
Input/output
connection
Hardwired (dual input)
Battery
External, 300-312 cells
870
INPUT
Nominal voltage
220/380, 230/400, 240/415 Vac three phase
Voltage range
-20%, +15% from nominal
50/60 Hz (4565 Hz)
Power factor
0,99
Current distortion
(THDi)
<3%
OUTPUT
Nominal voltage
220/380, 230/400, 240/415 Vac three phase
Frequency
50/60 Hz
Voltage regulation
1% static; 5% dynamic 100% load change, <20 ms recovery time
PF acceptable
without de-rating
Lagging to leading 0,9
Overload capacity
101125% for 10 min (on-line), 126150% for 1 min (on-line),
1000% for 1 cycle (bypass)
Efficiency (SOL)
Efficiency (Eco-mode)
OPTIONS
95%-98%
>98%
Parallel capacity/redundancy, sync control, isolation transformer, external bypass, external battery cabinets,
battery switch box, battery thermal probe, transformers/autotransformers for voltage adaption, top cable entry
USER INTERFACE
Front panel
Standard
communication ports
Optional
Graphical LCD display, mimic with LEDs and keyboard
RS232 serial port, USB, Remote Emergency Power Off input, Battery Switch status monitoring,
External Manual Bypass status monitoring, Diesel Mode
Web/SNMP, ModBus, relay, modem cards; remote panel; monitoring, managing and shutdown software
ENVIRONMENTAl
Operating temperature
Storage temperature
Altitude
Audible noise
at 1 meter (dBA)
0C +40C
-10C +70C
<1000 m
<60
STANDARDS AND CERTIFICATION
Marking
CE, GOST, ECA, ETL
Safety
IEC EN 62040 -1
EMC
IEC EN 62040 -2
Test and Performance
IEC EN 62040 -3
Quality
and Environment
ISO 9001: 2008, ISO 14001: 2004
BORRI S.p.A.
Industrial Power Solutions
Via 8 Marzo, 2 52010 Soci - Bibbiena (Arezzo) Italy
tel. +39.0575.5351 fax +39.0575.561438
www.borri.it [email protected]
Printed in Italy 11 2011
Frequency
