MAN B&W Diesel A/S
SL95-328/UM
August 1995
Service Letter
K/L/S-MC/MC-C
Cylinder Condition Report
New Measuring Points for Cylinder Liner Wear
Dear Sirs,
When introducing the L-MC/MCE type engines in the beginning of
the eighties, we transferred the definitions for measuring
points for cylinder wear from the L-GB engines.
The definitions of the eight levels were:
Pos.
Pos.
Pos.
Pos.
Pos.
1-4 coincide with the piston rings in TDC.
5
coincides with the level of the lubricating oil
quills.
6
the position at which the top piston ring reaches
the highest piston speed.
7
just above the scavenge ports.
8
below the 4th ring in BDC.
On the L-MC engines, the above levels give a reasonably even
distribution of the measuring points, and thus a good picture
of the wear profile along the running surface.
However, on the K-MC engines and, in particular, on the
S-MC engines, the above positions are not optimal, and we have
therefore decided to adjust the measuring points accordingly.
In order to cover the long stroke of the S-engines, we have
found it beneficial to introduce three additional measuring
points. At the same time, we have omitted the position that
corresponds to the highest piston speed as, in some engine
sizes, this position is very close to the level of the
lubricating oil quills.
HEAD OFFICE (& Postal address)
Teglholmsgade 41
DK-2450 Copenhagen SV
Telephone: +45 33 85 11 00
Telex: 16592 manbw dk
Telefax: +45 33 85 10 30
E-mail:
[email protected]http://www.manbw.dk
DIESEL SERVICE
Teglholmsgade 41
DK-2450 Copenhagen SV
Telephone: +45 33 85 11 00
Telex: 31197 manbw dk
Telefax: +45 33 85 10 49
E-mail: [email protected]
PRODUCTION
Teglholmsgade 35
DK-2450 Copenhagen SV
Telephone: +45 33 85 11 00
Telex: 19023 manfw dk
Telex: 19042 manfw dk
Telefax: +45 33 85 10 17
E-mail: manufacturing/[email protected]
FORWARDING
Teglholmsgade 35
DK-2450 Copenhagen SV
Telephone: +45 33 85 11 00
Telex: 19023 manfw dk
Telex: 19042 manfw dk
Telefax: +45 33 85 10 16
MAN B&W Diesel A/S
Denmark
Reg.No.: 24 231
The new definitions of measuring points are as follows:
Pos.
Pos.
Pos.
Pos.
Pos.
Pos.
1-4 coincide with the piston rings in TDC.
5-6 are evenly spaced between positions 4 and 7.
7
coincides with the level of the lubricating oil
quills, i.e. the same position as the previous
pos. 5.
8-9 are evenly spaced between positions 7 and 10.
10 just above the scavenge ports, i.e. the same
position as the previous pos. 7.
11 placed below the 4th ring in BDC.
We enclose our sheet "Measuring points for cylinder liner
wear", which specifies the measuring points for each engine
type. We recommend that you introduce the new measuring points
and that you correct the templates for cylinder liner measuring
accordingly.
We should further like to introduce our modified version of the
sheet "Cylinder Condition Report". We propose that you use this
sheet in connection with every piston overhaul so as to ensure
the recording of the most relevant parameters.
You are most welcome to send copies of these cylinder condition
reports to our office, where the reports will be used in the
statistical follow-up on the engines.
Our address is:
MAN B&W Diesel A/S
Engineering Operation Dept.
Teglholmsgade 41
DK-2450 Copenhagen SV, Denmark
Fax No.: +45 33 85 10 30
Yours faithfully,
MAN B&W Diesel A/S
