f

Chunghwa Picture Tubes, Ltd.

Technical Specification
To
:
Date : 2007.08.23
CPT TFT-LCD

CLAA320WF01

ACCEPTED BY

APPROVED BY

CHECKED BY

PREPARED BY

Product Planning
Management
General Division

Product Planning Management General Division

CHUNGHWA PICTURE TUBES, LTD.

1127 Hopin Rd., Padeh, Taoyuan, Taiwan 334, R.O.C.
TEL: +886-3-3675151 FAX: +886-3-377-3054

Doc.No: CLAA320WF01 D-SPEC-NEW-20070823

T- 3650002- 000- A NEW

Issue Date:

2007/08/23

CPT

CHUNGHWA PICTURES TUBES, LTD.,

RECORD OF REVISIONS
Revision No.

Date

new

2007/08/21

CPT Confidential

Page

Description
The first edition issued.

1/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

CONTENTS
No

Item

Page

OVERVIEW

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

INTERFACE PIN CONNECTION

10

INTERFACE TIMING

13

DATA MAPPING

18

MECHANICAL SPECIFICATION

19

OPTICAL CHARACTERISTICS

21

RELIABILITY TEST CONDITIONS

25

10

HANDLING PRECAUTIONS FOR TFT-LCD MODULE

26

11

VISUAL INSPECTION SPECIFICATION

28

CPT Confidential

2/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

1. OVERVIEW
CLAA320WF01 is 32 color (80.04 cm) TFT-LCD (Thin Film Transistor Liquid Crystal Display)
module composed of LCD panel, LVDS driver ICs, control circuit and backlight. By applying 8 bit
digital data, 1366*768, 16.7 million-color images are displayed on the 32 diagonal screen. Interface of
data and control signals is Typ. inverter for backlight is included in this module. General specification
are summarized in the following table:
ITEM
Display Area (mm)
Number of Pixels
Pixel Pitch (mm)
Color Pixel Arrangement
Display Mode
Number of Colors
Color Gamut
Color Temperature
Brightness
Viewing Angle
CR20
Wide View Tech.
Electrical Interface
Response Time (GTG)
Power Consumption
Module Size (mm)
Module Weight (g)
Backlight Unit
Surface Treatment

SPECIFICATION
697.6845(H)x392.256(V)
(31.51-inch diagonal)
1366 3(H) 768(V)
0.51075(H) 0.51075(V)
RGB vertical stripe
Normally black
16.7M
NTSC 75%
10000K
500 cd/m2
-85~85(H) , --85~85(V)
MVA
LVDS
8ms
(115W)
760.01(W) 450.01 (H) 45.01 (D)
(including inverter)
7500(Typ.)
CCFL, 14 tables
Hard coating, Anti-glare ,
Surface-hardness : 3H
< Reflection 4 % >

The LCD products listed on this document are not suitable for use of aerospace equipment, submarine
cables, and nuclear reactor control system and life support systems. If customers intend to use these
LCD products for above application or not listed in "Standard" as follows, please contact our sales
people in advance.
Standard : Computer, Office equipment, Communication equipment, Test and Measurement
equipment, Machine tool, Industrial robot, Audio and Visual equipment, Other consumer
products.

CPT Confidential

3/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

2. ABSOLUTE MAXIMUM RATINGS

The following are maximun values which, if exceeded, may cause faulty operation or damage to the
unit.
ITEM
Power Supply Voltage For LCD
Input Voltage of Inverter
Invert Dimming
BL on/off
ESD for Connector
ESD for Module
Operation Temperature (Surrounding)
Storage Temperature

SYMBOL
VCC
VBL
PDIM
ON/OFF
VESD
VESD
Top
Tstg

MIN.
-0.3
-0.3
-0.3
-0.3
-250
-15
0
-20

MAX.
12.6
27.0
3.5
5.5
250
15
50
60

UNIT
REMARK
V
V
Vdc
Vdc
V
KV

*1) *2) *3) *4)

*1) *2) *3) *4)

[Note]
*1) The relative temperature and humidity range are as below sketch, 90%RHMax. (Ta40)
*2) The maximum wet bulb temperature 39(Ta40) and without dewing.
*3) If you use the product in a environment which over the definition of temperature and humidity
too long to effect the result of eye-atching.
*4) If you operate the product in normal temperature range, the center surface of panel should be
under 60.

Humidity
Humidity85%RH without condensation.
Relative Humidity 90% (Ta 40)
Wet Bulb Temperature 39(Ta40)
90%

60
60%%
Wet Bulb
Temperature [C]

Storage

40

40%

30
20
10

10%

-20

10

Humidity [(%)RH]

50

20

30

40

50

60

70

80

Dry Bulb Temperature [C]

CPT Confidential

4/30

CLAA320WF01D-SPEC-20070823

Operation

CPT

CHUNGHWA PICTURES TUBES, LTD.,

3. ELECTRICAL CHARACTERISTICS
(a). TFT-LCD
ITEM
SYMBOL
LCD Power Supply Voltage
VCC
Ripple Voltage
Vrpd
Rush Current
Irush
White
LCD Power
ICC
Black
Supply Current
RGB stripe
LCD Power Consumption
Pc
High Input Voltage of LVDS
VIN+
Low Input Voltage of LVDS
VINInput Common Voltage of LVDS
VCM
Input Terminal Resist of LVDS
RT

MIN
11.4
-------100
---

TYP
12.0
--350
300
320
(7)
--1.25
100

MAX
12.6
100
4
900
600
700
12
100
---

Ta=25
UNIT
REMARK
V
[Note 1]
mVp-p VCC=+12.0V
A
[Note 2]
mA
W
mV
mV
V
ohm

[Note 3]

[Note 4]

[Note 1] The module should be always operated within above ranges.

[Note 2] Measure conditions
VCC
Q1
2SK1475

DC
+12V

FUSE
C3
1uF

LCD Module
Input

R1
47k

Q2
2SK1470
SW
(High to low)
(control signal)

R2
1k

C2
0.01uF

VR1
47k

+12V

DC
+15V

0.9Vcc

C1
1uF

0.1Vcc

1ms

GND

Vcc rising time is 1 ms

CPT Confidential

5/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

[Note 3] The sppecified power supply current is under condition at VCC=12VTa=252

fv=60Hzwhereas a power disspation check pattern is displayed.
a. White pattern

b. Black pattern

c. RGB Stripe pattern

[Note 4]LVDS signal definition

VID = VIN+ VIN-

VCM = VCM+VCM-
VID = VID+VID-
VID+ = VIH+VIH-
VID- = VIL+VIL-
VCM = ( VIN++VIN- ) / 2
VCM+ = ( VIH++VIH- ) / 2,
VCM- =( VIL++VIL- ) / 2

CPT Confidential

6/30

VINPositive Polarity differential DATA CLK input

VINNegative Polarity differential DATA CLK input

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(b).Power and signal sequence

VCC12V
90%

90%

Power Supply
(VCC12V)

10%

10%

T1

T4
T2

T3

Interface Signal
(LVDS Data with H,Vsync
and DENA)
DE)

T5
T6

BL on
Power Supply for
Backlight

Table 1. Power Sequence

Value

Parameter

Unit

Min

Typ

Max

T1

---

30

ms

T2

---

50

ms

T3

---

50

ms

T4

2000

---

ms

T5

110

---

ms

T6

100

---

ms

Notes1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid , be sure to pull down the power supply for LCD to 0V.
3. Lamp power must be turned on after the interface signal of the LCD panel are valid.

VCC-dip state
1) When 9VVCC11.4 Vtd10 ms.
2) VCC 11.4VVCC-dip condition should also follow the VCC-turn-off condition.

9V

CPT Confidential

7/30

11.4V

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(c). Inverter and Lamp Specification for Back Lighting

Ta = 25C, VCC=12V ,Turn on for 30 minutes
SYMBOL MIN
ITEM
TYP
MAX
UNIT
REMARK
Lamp Life Time

LT

50000

--

--

hr

*1)

Input Voltage

VIN

21.6

24

26.4

*2)

Input Current

IIN

--

4.5

(5.5)

*3)

External PWM Frequency

FDIM

100

--

350

Hz

External PWM Dimming

Control Voltage

PDIM

2.0

--

3.3

High *4)

PDIM

--

0.8

Low *4)

Vsel

2.0

--

3.3

High

Vsel

--

0.8

Low

Internal PWM Dimming

Control Voltage

PDIM

--

3.3

*5)

OSC Frequency

FOSC

61.5

63.5

65.5

kHz

In-Rush Current

IBRS

--

PWM Dimming control

Duty

PDIM

20

--

100

PWM select Voltage

ON/OFF
Control Voltage

ON
OFF

Power Consumption
(Backlight )

ON/OFF
BLW

--

0.8

--

108

(132)

V
W

*3)

Definition of the ( . ) : The value is variation

CPT Confidential

8/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

[Note1] Definition of the lamp life time
When lamp luminance reduce to 50% or lower than its initial value.
[Note2] Ripple voltage that occur at the instant of power-on cant exceed 27V.
[Note3] 25; after power on for 30 Minutes; Max value of the power consumption and input
current is measured at initial turn on of the backlight.
[Note 4] Duty Signal Input with 3.3V TTL specification.
[Note 5] Internal PWM control with Analog input voltage.
Brightness is the darkest when VDIM = 0V ;
Brightness is the brightest when VDIM = 3.3V .

CPT Confidential

9/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

4. INTERFACE PIN CONNECTION

(a).Connector Part No.20389-030E(I-PEX) or FI-X30SSL-HF(JAE) or compatible
Pin NO
Symbol
Description
Note
+12VDCRegulated
1
VCC
+12VDCRegulated
2
VCC
+12VDCRegulated
3
VCC
+12VDCRegulated
4
VCC
5
GND
Ground
6
Frame Rate Select
OD LUT Selection(Ground / NC)
(1)(2)
7
DE/Sync
DE/Sync Option
(1)(3)
8
GND
Ground
9
DMS
LVDS DATA MAPPING
(1)(4)
10
NC
NC
(1)
11
GND
Ground
12
RxIN0Data13
RxIN0+
Data+
14
GND
Ground
15
RxIN1Data16
RxIN1+
Data+
17
GND
Ground
18
RxIN2Data19
RxIN2+
Data+
20
GND
Ground
21
RxCLKINClock22
RxCLKIN+
Clock+
23
GND
Ground
24
RxIN3Data25
RxIN3+
Data+
26
GND
Ground
27
NC
Reserved
(1)
28
NC
Reserved
(1)
29
GND
Ground
30
GND
Ground
[Note 1] NC : Must let it open
[Note 2] PAL/NTSC option
Frame Rate Select (Pin 6)
Frame Rate
GND
PAL (50Hz)
NC
NTSC(60Hz)
OD EEPROM need two if support both PAL and NTSC(option)
[Note 3] DE / Sync option
DE/Syns(Pin 7)
GND
NC

mode
DE
Sync

[Note 4] LVDS OPTION PIN (DMS)

DMS(Pin 9)
LVDS format
LOW/OPEN
Non-JEIDA
3.3V
JEIDA
CPT Confidential

10/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(b) LVDS InterfaceLVDS ReceiverTcon (LVDS Rx merged)

TxOUT/RxIN0

TxOUT/RxIN1

TxOUT/RxIN2

TxOUT/RxIN3

CPT Confidential

LVDS pin
TxIN/RxOUT0
TxIN/RxOUT1
TxIN/RxOUT2
TxIN/RxOUT3
TxIN/RxOUT4
TxIN/RxOUT6
TxIN/RxOUT7
TxIN/RxOUT8
TxIN/RxOUT9
TxIN/RxOUT12
TxIN/RxOUT13
TxIN/RxOUT14
TxIN/RxOUT15
TxIN/RxOUT18
TxIN/RxOUT19
TxIN/RxOUT20
TxIN/RxOUT21
TxIN/RxOUT22
TxIN/RxOUT24
TxIN/RxOUT25
TxIN/RxOUT26
TxIN/RxOUT27
TxIN/RxOUT5
TxIN/RxOUT10
TxIN/RxOUT11
TxIN/RxOUT16
TxIN/RxOUT17
TxIN/RxOUT23

11/30

JEIDA-DATA
R2
R3
R4
R5
R6
R7
G2
G3
G4
G5
G6
G7
B2
B3
B4
B5
B6
B7

Non-JEIDA-DATA

Hsync
Vsync

R0
R1
R2
R3
R4
R5
G0
G1
G2
G3
G4
G5
B0
B1
B2
B3
B4
B5
Hsync
Vsync

DENA
R0
R1
G0
G1
B0
B1
Reserved

DENA
R6
R7
G6
G7
B6
B7
Reserved

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(c) Inverter Connector
1.) Connector(Receptacle) S14B-PH-SM3-TB(JST) or compatible.
2.) Mating connector(Plug) PRH-14(JST) or compatible.
Pin
No

Symbol

Description

Default

VIN

Operating Voltage Supply, +24V DC regulated

24V

VIN

Operating Voltage Supply, +24V DC regulated

24V

VIN

Operating Voltage Supply, +24V DC regulated

24V

VIN

Operating Voltage Supply, +24V DC regulated

24V

VIN

Operating Voltage Supply, +24V DC regulated

24V

BLGND

Ground and Current Return

GND

BLGND

Ground and Current Return

GND

BLGND

Ground and Current Return

GND

BLGND

Ground and Current Return

GND

10

BLGND

Ground and Current Return

GND

11

NC

NC

NC

12

ON/OFF

BL On : High (2.0~5.0)V
BL Off : NC/GND (0~0.8)V

On

13

PDIM(1)
PWM
-SEL

External PWM Dimming or Internal PWM Dimming

GND: External PWM Dimming (Pin 13)
NC /High : Internal PWM with Analog input(Pin 13)

14

100%
High*2)

[Note]
(1) PDIM is PWM duty control Input for +3.3V TTL Level Signal. This Input Signal is Continuous
Pulse Signal with +3.3V, TTL Level Signal Spec. If this is NC or +3.3V, 100% Duty (i.e.
+3.3V, DC level), Back Light should perform 100% Luminance. Duty Ratio of this Input
signal should be proportional relationship in certain range of control without any kind of
inherent side effect like Waterfall effect on Screen. Guaranteed Duty Range and Dimming Ratio
should be specified with supplementary measurement result.
(2) 14th Pin is selection pin for PWM control method; if this pin is connected to GND, VDIM
th

input of 13 Pin should have Logic Level Duty Signal for PWM control. If this is set to High or
th

Open, 13 Pin should have DC level signal.

CPT Confidential

12/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

5. INTERFACE TIMING
(1) Timing Specification
ITEM

SYMBOL

MIN.

TYP.

MAX.

UNIT

Freq.

fCLK

62

80

84

MHz

Cycle

tCLK

14.7

12.5

11.9

ns

Line Rate

fH

37.1

48.6

56

kHz

Horizontal
Total Time

tH

1575

1648

1936

tCLK

Horiaontal
Effective Time

tHA

1366

1366

1366

tCLK

Horizontal
Blank Time

tHB

209

282

570

tCLK

Frame Rate

Fr

47

60

63

Hz

Vertical
Total Time

tV

(796)

810

(870)

tH

Vertical
Effective Time

tVA

768

768

768

tH

Vertical
Blank Time

tVB

22

42

120

tH

Horizontal
Sync Time

tHsync

---

136

---

tCLK

Horizontal
Back Porch

tHBP

---

108

---

tCLK

Vertical
Sync Time

tVsync

---

---

tH

Vertical
Back Porch

tVBP

---

22

---

tH

Note

DCLK

Horizontal

DENA
Mode
LCD
Timing
Vertical

Horizontal
Sync
Mode
Vertical

CPT Confidential

13/30

CLAA320WF01D-SPEC-20070823

PAL:47~53Hz
NTSC:57~63Hz

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(2) Timing Chart

a. Horizontal Timing
DCLK

First Data

DATA
(R,G,B)

Invalid Data

1365

1366

Invalid Data

Last Data
t HBP

t HFP

tHA

DENA

tH=1/fH
Hsync

thsync

thsync

b. Vertical Timing Chart

HD

LINE DATA

Invalid Data

t VBP

767

t VA

768

Invalid Data

tVFP

DENA

tV=1/fV
Vsync

tvsync

CPT Confidential

tvsync

14/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(3) LVDS DATA MAPPING

a.Non-JEIDA normal specification

1CLK
RXCLKIN

R1

R0

G0

R5

R4

R3

R2

RXIN1

G2

G1

B1

B0

G5

G4

G3

G2

G1

RXIN2

B3

B2

DENA

Vsync

Hsync

B5

B4

B3

B2

RXIN3

R7

R6

Reserved

B7

B6

G7

G6

R7

R6

PREVIOUS

R1

R0

RXIN0

DATA for current CLK cycle

b.JEIDA specification

8bit LSB:R0,G0,B0
Parallel TTL Data Inputs Mapped to LVDS Outputs

CPT Confidential

15/30

CLAA320WF01D-SPEC-20070823

NEXT

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(4) LVDS INTERFACE

8bit LSBR0,G0,B0
JEIDA :Parallel TTL Data Inputs Mapped to LVDS Outputs
TRANSMITTER(THC63LVD823) INTERFACE CONNECTOR
INPUT DATA

51

TA0

R2

52

TA1

R3

54

TA2

R4

55

TA3

56

TA4

TA5

R7 (MSB)

TA6

G2

TB0

G3

TB1

G4

11

TB2

G5

12

TB3

14

TB4

15

TB5

B2

19

TB6

B3

20

TC0

B4

22

TC1

B5

23

TC2

B6

24

TC3

27

TC4

28

TC5

Vsync

30

TC6

DENA

50

TD0

R0 (LSB)

TD1

R1

TD2

G0 (LSB)

10

TD3

16

TD4

18

TD5

B1

25

TD6

Reserved

CPT Confidential

HOST

TxOUT0+
TxOUT0-

TxOUT1+
TxOUT1-

TxOUT2+
TxOUT2-

TxOUT3+
TxOUT3-

16/30

TFT_LCD

TIMING CONTROLLER INPUT

PIN NO

RxIN0+
RxIN0-

RxIN1+
RxIN1-

RxIN2+
RxIN2-

RxIN3+
RxIN3-

R5
R6

G6
G7 (MSB)

B7 (MSB)
Hsync

G1
B0 (LSB)

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(5) Color data assignment

[Note]
(1) Definition of gray scale
Color (n)n indicates gray scale levelhigher n means brighter level.
(2)Data1-High0-Low

CPT Confidential

17/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

6. BLOCK DIAGRAM

TFT-LCD Module
Timing
Controller
Source Driver

RxIN2 +/RxIN3 +/RxCLKIN +/-

Vcc=12V

INPUT CONNECTOR

RxIN1 +/-

Voltage Supply
for Gray Levels

Gate Driver

RxIN0 +/-

LCD Panel

1366 X 3 X 768

DC/DC

GND

Backlight

Converter

BACKLIGHT UNIT
Lamp connector
HV CP0404S0000(CVILUX)*7 or compatible
Mating connectorCP042CP1MT0 (CVILUX) or compatible

HV

CPT Confidential

18/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

7. MECHANICAL SPECIFICATION
(1) Front side ( include inverterif the sizes of a panel dont show the differential valueplease
follow the values show as differential range table. )
[Unit: mm]

CPT Confidential

19/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

(2) Rear side ( include inverterif the sizes of a panel dont show the differential valueplease follow
the values show as differential range table. )
[Unit: mm]

CPT Confidential

20/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

8.OPTICAL CHARACTERISTICS
Ta = 25C, VCC=12V
ITEM
Contrast (CEN)
Central
Luminance
Luminance 9P Luminance
(CEN)
(AVG)
Uniformity
Dimming 100%
esponse Time
( Gray to Gray Average )
Image Sticking
Horizontal
View Angle
Vertical
Crosstalk Ratio

SYMBO
CONDITION
L
= 0
CR
Point-5
= 0

= 0

= 0

= 0

= 0

= 0

trg , tfg
tis

CMR

MIN.

TYP.

MAX.

800

1000

--

380

500

--

*1)*2)*3)

cd/m2

*9)

500

--

cd/m2

*2)*3)

75

--

--

*2)*3)

= 0

--

(15)

ms

*4)

4h
CR 20
Point-5
= 0

--80~80
-80~80
--

--85~85
-85~85
--

(3)
--(1)

*5)
*2)*3)
*2)*3)
*3)*6)

--

*2)*3)

Red

Rx
Ry

(0.628)
(0.283)

(0.658)
(0.313)

(0.688)
(0.343)

Green

Gx
Gy

(0.255)
(0.575)

(0.285)
(0.605)

(0.315)
(0.635)

Blue

Bx
By

(0.113)
(0.050)

(0.143)
(0.080)

(0.173)
(0.110)

White

Wx
Wy

0.253
0.267

0.28
0.29

0.313
0.327

Color Temperature
Color Gamut

Tc
CG

Color
Temperature
Coordinate

UNIT Remarks

= 0
Point-5

-10000
-K
*3)
-75
-%
*7)
Definition of the ( . ) : The value is variation

[Note]
These items are measured usingBM-5A (TOPCON)
View AngleEZ contrast XL-88Response TimeWestar TRD-100
[ under the dark room condition (no ambient light). ]
Definition of these measurement items is as follows
*1) Definition of Contrast Ratio
CR=ON (White) Luminance/OFF (Black) Luminance
*2) Definition of Luminance and Luminance uniformity and Contrast and the Deviation of Color
Coordinate

CPT Confidential

21/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

Luminance and ContrastTo measure at the center position 5 on the screen (NO.5)see Fig.81 below.
Luminance UniformityLw (MAX) and Lw(MIN) are the maximum and minimum luminance
value measure at the position 1~5 on the screen (NO.1~5)see Fig.81 and below show equation
Lw[Lw(MIN)) / Lw(MAX) ] 100%
he Deviation of Color CoordinateTo measure at the position 1~9 on the screen (NO.1~9)
see Fig.8-1 below.

683

228

1138

(1, 1)
128

384

640
(1366, 768)

Figure 8-1. Measurement positions

*3) Definition of Viewing Angle ( )

Figure 8-2. Definition of Viewing Angle

CPT Confidential

22/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

*4) Definition of Response Time ( Gray to Gray Average )

(0~255 th )
90%

90%

L u m in a n ce
(G ray S cale L evel)
(0~255 th )
trg

10%

10%

tfg

Figure 8-4. Definition of Response Time ( Gray Scale Level )

The driving signal time means the signal of gray level 0316395127159191223
255.
Gray to Gray Average means the average switching time of gray level 0316395127
159191223255 to each other.
The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature
change during measuring. In order to stabilize the luminancethe measurement should be
executed after lighting backlight for 1 hour in a windless room.
*5) Image sticking test method:
Continuously display the test pattern shown in the figure below for specified time. To change the
module frame to gray pattern ( gray 120 pattern ) , and its displaying grade still under
specfication.
W h ite B lo c k
(2 5 6 G L )
3 0 -P ix e l

B la c k B a c k g r o u n d
30(0 G L )

3 0 -P ix e l

Figure 8-5. The pattern of image sticking test

CPT Confidential

23/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

*6) Definition of Cross Talk RatioCMR = MAX ( ( | ( LB1-LA ) / LA | ) 100 ( | (LB2 LA ) /

LA| ) 100 )
LA Pattern A(Half-Tone pattern) Measure point Luminance
LB1LB2 Pattern B1Pattern B2 Measure point Luminance
Pattern B1
Gray 128

(683,96)

(341,192)
(171,384)

Black

Pattern A

(1195,384)
(1024,576)

(683,672)
GRAY
Gray128
127

Pattern B2

(0,0)
Gray128

White

measurement point

(1366,768)
Figure 8-6. The pattern of cross talk test
*7) Definition of Color Gamut:
To measure RGB three sub-pixels color gamut coordinate at CIE coordinate chart from the center
of module , to form a triangle area = ARGB.
RGB three sub-pixels of NTSC at CIE coordinate chart to form a triangle area = NRGB.
CG =

ARGB
NRGB

100

*8) Definition of Central Luminance:

After lighting on the panel 30 mins, you can proceed the Central Luminance testing.
The definiton of TYP value is under status of Inverter Dimming Voltage=3.3V.

CPT Confidential

24/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

9.RELIABILITY TEST CONDITIONS

(1) Temperature and Humidity
TEST ITEMS
High Temperature Operation
High Temperature Storage
High Temperature
High Humidity Operation
Low Temperature Operation
Low Temperature Storage
Thermal Shock

CONDITIONS
50240hrs
60240hrs
5090% RH240 hrs
(No condensation)
0240 hrs
-20240 hrs
Between -20(1hr) and 60(1hr)
50 Cycles

(2) Shock & Vibration

ITEMS

CONDITIONS
Shock level980m/s (100G)
Waveformhalf sinusoidal wave, 2ms
Number of shocksone shock input in each direction of three
mutually perpendicular axes for a total of six shock inputs.
Vibration level14.7m/s2(1.5G) zero to peak
Waveformsinusoidal
Frequency range10 to 300 Hz
Frequency sweep rate0.5 octave/min
Durationeach xyz axis10 mintotal 30 mins
2

Shock
(Non-Operation)

Vibration
(Non-Operation)

(3) ESD test

Test Item
Connector

Module

Test statements
200 pF0 250 V
By using contact-mode to discharge each pin one time and then check the
module frame.
150pF33015KV
1.Under test conditions, by using air-mode to discharge each test point 25
times continuously and then check the module frame.
2. Under test conditions, by using contact-mode to discharge each test point
of panel frame 25 times continuously and then check the module frame.

(4) Judgment standard

The judgment of the above test should be made as follow:
Pass: Normal display image with no obvious non-uniformity and no line defect.
Partial transformation of the module parts should be ignored.
Fail: No display image, obvious non-uniformity, or line defects.

10. HANDLING PRECAUTIONS FOR TFT-LCD MODULE

CPT Confidential

25/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

Please pay attention to the followings in handling TFT-LCD products

10.1 ASSEMBLY PRECAUTION
(1) Please use the mounting hole on the module side in installing and do not beading or wrenching
LCD in assembling. And please do not drop, bend or twist LCD module in handling.
(2) Please design display housing in accordance with the following guidelines.
Housing case must be destined carefully so as not to put stresses on LCD all sides and not to
wrench module. The stresses may cause non-uniformity even if there is no non-uniformity
statically.
Keep sufficient clearance between LCD module back surface and housing when the LCD
module is mounted. Approximately 1.0 mm of the clearance in the design is recommended
taking into account the tolerance of LCD module thickness and mounting structure height
on the housing.
When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD
module, still sufficient clearance is required, such as 0.5mm. This clearance is, especially, to
be reconsidered when the additional parts are implemented for EMI countermeasure.
Design the inverter location and connector position carefully so as not to give stress to lamp
cable, or not to interface the LCD module by the lamp cable.
Keep sufficient clearance between LCD module and the others parts, such as inverter and
speaker so as not to interface the LCD module. Approximately 1.0mm of the clearance in
the design is recommended.
(3) Please do not push or scratch LCD panel surface with any-thing hard. And do not soil LCD
panel surface by touching with bare hands. (Polarizer film, surface of LCD panel is easy to be
flawed.)
(4) Please do not press any parts on the rear side such as source TCP, gate TCP, control circuit board
and FPCs during handling LCD module. If pressing rear part is unavoidable, handle the LCD
module with care not to damage them.
(5) Please wipe out LCD panel surface with absorbent cotton or soft clothe in case of it being soiled.
(6) Please wipe out drops of adhesives like saliva and water on LCD panel surface immediately.
They might damage to cause panel surface variation and color change.
(7) Please do not take a LCD module to pieces and reconstruct it. Resolving and reconstructing
modules may cause them not to work well.
(8) Please do not touch metal frames with bare hands and soiled gloves. A color change of the metal
frames can happen during a long preservation of soiled LCD modules.
(9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with
inverter.
10.2 OPERATING PRECAUTIONS
(1) Please be sure to turn off the power supply before connecting and disconnecting signal input
cable.
(2) Please do not change variable resistance settings in LCD module. They are adjusted to the most
suitable value. If they are changed, it might happen LCD does not satisfy the characteristics
specification.
(3) Please consider that LCD backlight takes longer time to become stable of radiation
characteristics in low temperature than in room temperature.
(4) A condensation might happen on the surface and inside of LCD module in case of sudden change
of ambient temperature.
(5) Please pay attention to displaying the same pattern for very long time. Image might stick on
LCD. If then, time going on can make LCD work well.
(6) Please obey the same caution descriptions as ones that need to pay attention to ordinary
electronic parts.
CPT Confidential

26/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

10.3 PRECAUTIONS WITH ELECTROSTATICS

(1) This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be
affected by electrostatics. Please be careful with electrostatics by the way of your body
connecting to the ground and so on.
(2) Please remove protection film very slowly on the surface of LCD module to prevent from
electrostatics occurrence.
10.4 STORAGE PRECAUTIONS
(1) When you store LCDs for a long time, it is recommended to keep the temperature between 0
~40 without the exposure of sunlight and to keep the humidity less than 90%RH.
(2) Please do not leave the LCDs in the environment of high humidity and high temperature such as
60 90%RH.
(3) Please do not leave the LCDs in the environment of low temperature; below -20.
10.5 SAFETY PRECAUTIONS
(1) When you waste LCDs, it is recommended to crush damaged or unnecessary LCDs into pieces
and wash them off with solvents such as acetone and ethanol, which should later be burned.
(2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off
throughly with soap and water.
10.6 OTHERS
(1) A strong incident light into LCD panel might cause display characteristics' changing inferior
because of polarizer film, color filter, and other materials becoming inferior. Please do not
expose LCD module direct sunlight Land strong UV rays.
(2) Please pay attention to a panel side of LCD module not to contact with other materials in
preserving it alone.
(3) For the packaging box, please pay attention to the followings:
Packaging box and inner case for LCD are designed to protect the LCDs from the damage or
scratching during transportation. Please do not open except picking LCDs up from the box.
Please do not pile them up more than 3 boxes. (They are not designed so.) And please do not
turn over.
Please handle packaging box with care not to give them sudden shock and vibrations. And
also please do not throw them up.
Packing box and inner case for LCDs are made of cardboard. So please pay attention not to
get them wet. (Such like keeping them in high humidity or wet place can occur getting them
wet.)

CPT Confidential

27/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

11. VISUAL INSPECTION SPECIFICATION

11.1 Inspection condition:
(1) Viewing distance is approximately 35 ~ 40 cm.
(2) Viewing angle is normal to the LCD panel as figure below(10).
(3) Ambient temperature is approximately 25 5.
(4) Ambient humidity is 60 5% RH.
(5) Ambient illumination is from 300 ~ 500 lux.
(6) Input signal timing should be typical value.

11.2 Special condition

(1) Viewing distance is close for inspection of adjacent dots and distance between defect dots.
(2) Viewing condition of Shot block non-uniformity from oblique angle is as figure below.
(3) Exceptional case: View angle 40 while inspected image-sticking.

CPT Confidential

28/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

11.3 Inspection Criteria

DEFECT TYPE

0.3mmW0.6mm
L30mm

N6

SPOT

3.0mm5.0mm

N9

Note1

FIBER
POLARIZER
BUBBLE
TOTAL

W6.0mm, L10mm

N9

Note1

0.3mm0.6mm

N9

Note1

SCRATCH

VISUAL DEFECT

INTERNAL

ELECTRICAL
DEFECT

Note

LIMIT

N12

BRIGHT DOT

N4

Note2

DARK DOT

N12

TOTAL DOT

N12

Note2

TWO ADJACENT DOT

6PAIRS

Note3

THREE ADJACENT DOT

4PAIRS

Note3

FOUR ADJACENT DOT

FIVE OR MORE
ADJACENT DOT
LINE DEFECT

3PAIRS

Note3

NOT ALLOWED

NOT ALLOWED

One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot)

[Note]
*1) W : Width[mm], L : Length[mm], N : Number, : Average Diameter

*2) Bright dot is defined through 5% transmission ND Filter as following.

CPT Confidential

29/30

CLAA320WF01D-SPEC-20070823

CPT

CHUNGHWA PICTURES TUBES, LTD.,

*3) Judge defect dot and adjacent dot as following. Allow below (A and B status) adjacent dot, including
bright and dart adjacent dot. And they will be counted 2 defect dots in Allow above (as E, F and G
status) three adjacent defect dots, including bright and dart dot. And they will be counted 3 defect
dots in total quantity. Allow above (as H, I, J, K, L, M and N status) four adjacent defect dots,
including bright and dart dot. And they will be counted 4 defect dots in total quantity.

*4) Mura is defined through transmission 1% ND Filter under 50% gray scale pattern as following.
*5)Other
(1) The defects that are not defined above and considered to be problem shall be refered to CPT limited sample first. It will be
reviewed and discussed by both parties secondly.
(2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.

CPT Confidential

30/30

CLAA320WF01D-SPEC-20070823

CPT

CPT Confidential

CHUNGHWA PICTURES TUBES, LTD.,

31/30

CLAA320WF01D-SPEC-20070823