APPENDIX A
Troubleshooting the Router
This appendix contains information about how to isolate problems with the router and
includes the following sections:
• Isolating Problems
• Reading the LEDs
Isolating Problems
The key to problem solving in this system is to try to isolate the problem to a specific
subsystem. By comparing what the system is doing to what it should be doing, the task of
isolating the problem is greatly simplified.
When problem solving, consider the following subsystems:
• Power and cooling systems—The power supply, power cable, and fan
• Ports and cables—The ports on the rear panel of the router and the cables that connect
to them
Troubleshooting the Router A-1
Isolating Problems
Troubleshooting the Power and Cooling Systems
Check the following items to help isolate the problem:
• When the power switch is in the ON position (|) and the System OK LED is on, are the
fans operating? If not, check the fans.
• Does the router shutdown after being ON a short time? Check the environmental
conditions. The router might be overheating, resulting in a thermal-induced shutdown.
Ensure that the chassis intake and exhaust vents are clear. Review the section “General
Site Requirements” in the chapter “Preparing to Install the Router.” The operating
temperature for the router is 32 to 104° F (0 to 40°C).
• Does the router fail to boot, but the System OK LED is on? Check the power supply.
• Does the router constantly or intermittently reboot? There might be a problem with
either the processor or the software, or a DRAM SIMM might be installed incorrectly.
For information about obtaining technical support, refer to the section “Obtaining Service
and Support” in the “Overview of the Router” chapter.
Troubleshooting the Ports, Cables, and Connections
Check the following items to help isolate the problem:
• Does the router fail to recognize a port? Check the cable connection.
• When the power switch is in the ON position (|), is the System OK LED on? If not,
check the power source and power cable.
• Does the system boot, but the console screen is frozen? Verify that the console is
configured for 9600 baud, 8 data bits, no parity, and 2 stop bits.
For information about obtaining technical support, refer to the section “Obtaining Service
and Support” in the “Overview of the Router” chapter.
A-2 Router Installation and Configuration Guide
Reading the LEDs
Reading the LEDs
The LEDs indicate the current operating condition of the router. You can observe the LEDs,
note any fault condition that the router is encountering, and then contact your system
administrator or customer service, if necessary. For information about how to contact
customer service, refer to the section “Obtaining Service and Support” in the “Overview of
the Router” chapter.
Figure A-1 to Figure A-7 show the location of the LEDs on the rear panel of the routers.
The power LED, at the right of the auxiliary port, lights up when the system is working
properly. All of the other LEDs indicate activity by flickering. When there is heavy activity
on a port, the LED might be ON constantly. If an LED is not ON when the port is active
and the cable is connected correctly, there might be a problem with the port.
Figure A-1 Model 2501 LEDs
Ethernet Synchronous System
AUI LED serial LEDs OK LED
Figure A-2 Model 2502 LEDs H4262
Token Ring Synchronous System
LED serial LEDs OK LED
H7578
Troubleshooting the Router A-3
Reading the LEDs
Figure A-3 Model 2503 LEDs
Ethernet Synchronous ISDN System
AUI LED serial LEDs BRI LED OK LED
H7579
Figure A-4 Model 2504 LEDs
Token Ring Synchronous ISDN System
LED serial LEDs BRI LED OK LED
H7580
Figure A-5 Model 2513 LEDs
Token Ring Ethernet Synchronous System
LED AUI LED serial LEDs OK LED
TOKEN RING
H7581
A-4 Router Installation and Configuration Guide
Reading the LEDs
Figure A-6 Model 2514 LEDs
Ethernet Synchronous System
AUI LEDs serial LEDs OK LED
H7582
Figure A-7 Model 2515 LEDs
Token Ring Synchronous System
LEDs serial LEDs OK LED
H7583
Troubleshooting the Router A-5
Reading the LEDs
A-6 Router Installation and Configuration Guide
