Computer-controlled, Cycle Machine

With Input Function

AMS-210E Series
ENGINEERS MANUAL

40034836
No.E369-02

PREFACE
This Engineers Manual is written for the technical personnel who are responsible for the service and maintenance
of the machine.
The Instruction Manual for these machines intended for the maintenance personnel and operators at an apparel
factory contains operating instruction in derail. And this manual describes Standard Adjustment, Adjustment
Procedures, Results of Improper Adjustment, and other important information which are not covered in the
Instruction Manual.
It is advisable to use the Input Instruction Manual, relevant Instruction Manual and Parts List together with this
Engineers Manual when carrying out the maintenance of these machines.
In addition, for the motor for the sewing machine with thread trimmer, refer to the separate Instruction Manual or
This manual gives the Standard Adjustment on the former page under which the most basic adjustment value is
described, and on the latter page Results if Improper Adjustment under which stitching errors and troubles
arising from mechanical failures and Hoe to adjust are described.

CONTENTS
1. Specifications ........................................................................................................ 1
2. Configuration ........................................................................................................... 2
(1) Names of main unit .................................................................................................................. 2
(2) IP-400 operation panel ............................................................................................................. 3
(3) CP-20 operation panel ............................................................................................................. 4

3. Standard adjustment .............................................................................................. 5

(1) Main shaft connection/disconnection .................................................................................. 5
(2) Removal of main shaft motor and coupling ......................................................................... 7
(3) Crank rod connection/disconnection ................................................................................... 9
(4) Crank balancer positioning ................................................................................................. 11
(5) Adjustment of intermediate presser cam ........................................................................... 13
(6) Adjustment of intermediate presser bar............................................................................. 13
(7) Intermediate presser variable connection /disconnection ............................................... 15
(8) Intermediate presser variable adjustments........................................................................ 17
(9) Intermediate presser drivie arm .......................................................................................... 19
(10) Lower shaft backlash adjustment and connection/disconnection .................................. 21
(11) Oscillator gear positioning .................................................................................................. 21
(12) Adjustment of hook oil amount ........................................................................................... 23
(13) Shuttle connection / disconnection and oil wick piping ................................................... 23
(14) Adjusting the height of the needle bar ............................................................................... 25
(15) Hook adjustment................................................................................................................... 27
(16) Thread trimmer presser lifter cam connection/disconnection ........................................ 29
(17) Thread trimmer and presser origin sensor adjustment ................................................... 29
(18) Adjusting the thread trimmer sensor ................................................................................. 31
(19) Adjustment of the moving knife and counter knife position ............................................ 33
(20) Floating amount of the thread tension disk ...................................................................... 33
(21) Second thread tension connection / disconnection ......................................................... 35
(22) AT unit connection / disconnection .................................................................................... 37
(23) Wiper adjustment ................................................................................................................. 39
(24) Adjusting the pre-load of the X-Y table .............................................................................. 41
(25) Adjustment of the tension of the X timing belt .................................................................. 43
(26) Adjustment to positions of X-motor and Y-motor (Backlash adjustment to gear) ......... 43
(27) Adjusting of the presser lower arm (Motor type only) ...................................................... 45
(28) Adjustment when the presser plate sheet is replaced (Motor type only) ....................... 45
(29) Height of the slider and pasting of the presser plate sheet
(Pneumatic type only) .......................................................................................................... 47
(30) Adjusting the speed of the work clamp feet (Pneumatic type only) ................................ 49
(31) Making the origin setting gauge ......................................................................................... 51
(32) Adjusting the X origin sensor ............................................................................................. 51
(33) Adjusting the Y origin sensor ............................................................................................. 53
(34) Adjustment of the bobbin winder driving wheel position ................................................ 55
(35) Adjusting the bobbin winder amount ................................................................................. 55
(36) Adjustment of the shuttle upper spring and lower thread holder position .................... 57
(37) Shuttle felt ............................................................................................................................. 57
(38) Shape of the shuttle race ring ............................................................................................. 59
(39) Adjustment of thread take-up spring ................................................................................. 59
(40) Needle thread clamp device connection/disconnection .................................................. 61
(41) Adjusting the needle thread clamp sensor ........................................................................ 63
(42) Adjusting the needle thread clamp notch .......................................................................... 65

4. Memory switch ...................................................................................................... 67

(1) Start and change .................................................................................................................... 67
(2) Function list ............................................................................................................................ 69

5. Supplemental remarks of each function number and

explanation of each function ............................................................................... 92
(1) Feeding frame operational sequence setup ........................................................................ 92
(2) Fixed refuge position setup .................................................................................................. 96
(3) Bank function setup ............................................................................................................... 97
(4) Port I/O setup ........................................................................................................................ 101
(5) Simplified program setup .................................................................................................... 112
(6) Version display ..................................................................................................................... 126
(7) Keylock setup ....................................................................................................................... 127
(8) Communication screens of the maintenance personnel level (Program rewrite) ......... 128
(9) Information screen at the maintenance personnel level .................................................. 134
(10) Test sewing function ......................................................................................................... 136

6. Test mode ........................................................................................................... 139

(1) Start (CP-20) ......................................................................................................................... 139
(2) Display output test (CP-20) ................................................................................................. 141
(3) Method of confirmation according to each test program No. (CP-20) ............................ 142
(4) For IP-400 .............................................................................................................................. 149

7. Printed wiring board and dip switch ................................................................ 165

(1) Various printed wiring boards ............................................................................................ 165
(2) Dipswitch setup .................................................................................................................... 173

8. Table of exchanging gauge parts according to sewing specifications and

needle size used ................................................................................................ 174
9. Option list ........................................................................................................... 175
(1) Method of pedal switch cable set connections ................................................................. 182
(2) Method of mechanical valve unit connections .................................................................. 184

10. Maintenance ....................................................................................................... 185

(1) Replacing the fuse ............................................................................................................... 185
(2) Changing the voltage specification .................................................................................... 186
(3) Greasing lock-tight parts .................................................................................................. 187
(4) Parts to which grease lock-tight is applied ..................................................................... 188
(5) Replenishing the designated places with grease ............................................................. 196

11. Error code list .................................................................................................... 198

12. Message list ....................................................................................................... 205
13. Troubles and corrective measures .................................................................. 208
(1) Mechanical parts .................................................................................................................. 208
(2) Sewing conditions ............................................................................................................... 212
(3) Electrical components ......................................................................................................... 220

14. Circuit diagrams ................................................................................................ 228

(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)

Block diagram A ................................................................................................................. 228

Power supply circuit diagram A ........................................................................................ 229
Power supply circuit diagram B ........................................................................................ 230
Power supply circuit diagram C ........................................................................................ 231
Servo motor circuit diagram .............................................................................................. 232
Sensor-pedal circuit diagram ............................................................................................ 233
MAINPANEL board circuit diagram ................................................................................. 234
Motorsolenoid circuit diagram ......................................................................................... 235
Air system circuit diagram................................................................................................. 236

15.Drawing of the table ........................................................................................... 237

1. Specifications
Model name

No.
Item

Application
AMS-210EHS

AMS-210ESS

Sub-class
1

Sewing area

Max. sewing speed

Stitch length

Feed motion of feeding frame

Needle bar stroke

AMS-210EHL

AMS-210ESL

AMS-210EHL

1306

AMS-210ESL

AMS-210EHL

1510

X-Direction (right, left) 130mm; Y-Direction (forward, backward) 60mm

AMS-210ESL

AMS-210EHL

2206

AMS-210ESL
2210

X-Direction (right, left) 150mm; Y-Direction (forward, backward) 100mm X-Direction (right, left) 220mm; Y-Direction (forward, backward) 60mm

X-Direction (right, left) 220mm; Y-Direction (forward, backward) 100mm

2700rpm (when sewing pitch is 3mm or less)

0.1 to 12.7mm (Min. resolution : 0.05mm)
intermittent feed (2-shaft drive by stepping motor)
41.2mm

Needle

Method to lift feeding frame

S type: DP x 5 # 14, H type: DP x 17 # 18

Feeding frame shape

Lift of feeding frame

10

Intermediate presser stroke

Standard 4mm (0 to 10mm)

11

Lift of intermediate presser

20mm

12

Intermediate presser
DOWN position variable

Standard 0 to 3.5mm (Max. 0 to 7.0mm)

13

Needle thread clamp device

14

Needle thread tension

15

Hook

16

Lubrication

Plane part: grease, hook part: minute volume lubrication (tank type)

17

Lubricating oil

JUKI NEW Defrix oil (equivalent to ISO VG32) (Lubrication system)

18

Grease

Pulse motor

Air

Right and left united

Right and left separated

Right and left united

Standard 25mm, Max. 30mm

H type

S type

Max. 30mm

H type

S type

H type

S type

H type

S type

H type

S type

Active tension (electronic thread tension control mechanism)

2-fold semi-rotary hook

1. Penetration No. 2 lithium grease, 2. Templex N2, 3. Juki Grease A, 4. Juki Grease B (Caution)1.

19

EEP-ROM, Smart media

EEP-ROM : Max. 200 patterns (Max. 20,000 stitches/pattern)
Smart media : Max. 999 patterns (Max. 50,000 stitches/pattern)

Memory of pattern data

20

Temporary stop facility

Used to stop machine operation during a stitching cycle.

21

Enlarging/Reducing
function

Allows a pattern to be enlarged or reduced on the X axis Y axis independently when sewing a pattern.
Scale : 1% to 400% times (0.1% steps)

22

Enlarging/Reducing
method

Pattern enlargement / reduction can be done by increasing / decreasing either stitch length or the number of stitches.
(Only increase/decrease of stitch length when pattern button is selected and CP-20 is used)

23

Sewing speed limitations

24

Pattern selector facility

Pattern No. selection method

(EEP-ROM : 1 to 200, Smart media : 1 to 999)
(CP-20 is the scroll type.)

25

No. of sheets counter

Up/Down method (0 to 9,999) (IP-400 only)

26

Sewing counter
(Bobbin thread counter)

27

Memory back-up

28

2nd origin setting facility

29

Sewing machine motor

30

External dimensions

1,200mm (W) x710mm (L) x 1,200mm (H)

(Excluding thread stand)

1,200mm (W) x770mm (L) x 1,200mm (H)

(Excluding thread stand)

1,200mm (W) x710mm (L) x 1,200mm (H)

(Excluding thread stand)

1,200mm (W) x770mm (L) x 1,200mm (H)

(Excluding thread stand)

31

Weight (gross weight)

Machine head : 69kg, Control box : 16.5kg

Machine head : 73kg, Control box : 16.5kg

Machine head : 75kg, Control box : 16.5kg

Machine head : 77kg, Control box : 16.5kg

200 to 2,700 rpm (Scale : 100 rpm steps)

Up/Down method (0 to 9,999)

In case of a power interruption, the pattern being used will automatically be stored in memory.
Using jog keys, a 2nd origin (needle position after asewing cycle) can be set in the desired position within the sewing area.
The set 2nd origin is also stored in memory. (IP-400 only)
Servomotor 550W

32

Power consumption

33

Working temperature/humidity

500VA

34

Supply voltage/frequency

35

Air pressure used

Standard: 0.35 to 0.4MPa, Max. 0.55MPa

36

Air consumption

1.8dm3 /min (ANR)

37

Needle highest position

stop facility

Temperature: 5-35C, Humidity: 35-85% (no condensation)

Rated voltage 10% 50 / 60Hz

(Caution) Grease type, refer to (3) Greasing lock-tite parts of [10] Maintenance

After the completion if sewing, the needle can be brought up to its highest position.

MEMO

2. Configuration
(1) Names of main unit

Air regulator
(for pneumatic type only)

Machine head
Wiper switch
Temporary stop switch
Feeding frame
Intermediate presser
Thread stand
Operation panel (IP-400 or CP-20)
Power switch
Control box
Foot pedal
Manual pedal (Excluding pneumatic type)

(2) IP-400 operation panel

(Front view)

(Right side view)

Touch panel LCD display section

READY key

Changeover of the data input screen and the sewing screen can be
performed.

INFORMATION key

Changeover of the data input screen and the information screen can
be performed.

COMMUNICATION key

Changeover of the data input screen and the communication screen

can be performed.

MODE key

Changeover of the data input screen and the mode changeover screen
which performs various detail settings can be performed.

Smart media card slot (Close the cover for use.)

Connector for RS-232C communication
Variable resistor for color LCD Screen contrast can be adjusted. Adjust it as you desire.
Connector for external input

(3) CP-20 operation panel

CP-20

Ready key
This key changes over the setting state from the panel
to the sewing state where the sewing machine actually operates.

Item selection LED

LEDs of the selected items light up.

Sewing LED
This LED goes off at the time of setting state and
lights up at the time of sewing state. Changeover
can be performed with Ready key.

Pattern No.

X scale

Y scale

Reset key
This key is used for canceling error or returning the
set value to the initial value.

Max. speed
limitation

Sewing
counter

Bobbin
winder

Intermediate
presser height

Thread tension

Mode key
This key makes the setting mode of the memory
switch.
+ / Feed forward key and - / Feed backward
key
This key is used for changing pattern No. and X/Y
scale, and feed forward/feed backward.
Selection key
This key selects the item to be set. Item selection
LED of the selected item and the set value are displayed.
Data indication LED
This LED indicates the set values of the selected
items such as pattern No., X/Y scale, etc.

Needle thread clamp ON/OFF key

This key selects effective/ineffective of needle thread
clamp. When it is effective, needle thread clamp
disply LED lights up.
Needle thread clamp display LED
When this LED lights up, needle threas clamp
operaters.
Pattern registration key
This key registers the pattern. When this key is
pressed, the pattern registered here can sew immediately.
X/Y scale, sewing position. etc. can be changed and
registered.

3. Standard adjustment
(1) Main shaft connection/disconnection
Procedures of disassembling
1. Loosen the set screw
securing the main shaft counterbalance , and remove the taper screw .
2. Loosen 2 set screws
(through the screwdriver hole A), 2 set screws , and 2 set screws .
On this occasion, loosen No. 2 set screw first, and completely remove No. 1 set screw from the flat part of the
main shaft .
3. Remove the main shaft motor .
Refer to 3.-(2) Removal of the main shaft motor and coupling.
4. Loosen 2 set screws .
On this occasion, be aware that the balancer
may rotate due to loosened set screws .
5. Loosen 2 set screws .
6. Loosen 2 set screws .
On this occasion, completely remove No. 1 set screw of the set screws
from the flat part of the main shaft
.
7. Loosen 2 set screws
and 2 set screws .
8. Pull out the main shaft
in the direction of Arrow C.

Main shaft taper hole

Screwdriver hole A
No. 2 set
screw

No. 2 set screw

No. 2 set screw
E
D

No. 1 set screw

No. 1 set screw

F
No. 1 set screw

Procedures of assembling
1. Insert the main shaft
into the crank rod , balancer , hand pulley gear A , bobbin winding drive
wheel , and main shaft counterbalance
in this order, and mount this assembly on the frame.
2. Tighten the taper screw
into the taper hole of the main shaft , and tighten the set screw
to secure
the main shaft counterbalance .
3. Lightly press the main shaft counterbalance
in the direction of Arrow D and the middle metal
in the
direction of Arrow E, and tighten 2 set screws .
(Tighten No. 1 set screw so that it touches the flat part of the main shaft . Then, tighten No. 2 set screw.
Same procedure hereafter)
4. Tighten 2 set screws
and 2 set screws . (Make sure that No. 1 set screw touches the flat part of the
main shaft .)
5. Press the hand pulley
in the direction of Arrow F to engage the hand pulley gear A with the hand pulley
gear B , and secure them with 2 set screws .
6. Mount the main shaft motor
and coupling .
Refer to 3.-(2) Removal of main shaft motor and coupling.
7. Secure the eccentric cam of the intermediate presser
with 2 set screws . Refer to 3.-(5) Adjustment
of intermediate presser cam.
8. Secure the crank rod
with 2 set screws . Refer to 3.-(3) Crank rod connection/disconnection.
9. Secure the balancer
with 2 set screws . Refer to 3.-(4) Crank balancer positioning.
10. Secure the bobbin winding drive wheel
with 2 set screws . Refer to 3.-(34) Adjustment of the bobbin
winder driveing wheel poition.
* Make sure that no torque is applied by rotating the main shaft .

(2) Removal of main shaft motor and coupling

Procedures of disassembling
1. For removal of the main shaft with the coupling,
Loosen 2 set screws
on the main shaft side of the coupling , and remove 4 set screws
securing the
motor.
2. For removal of the coupling
from the main shaft motor , loosen 2 set screws
on the main shaft motor
side.
(Caution) The screw (hole) that can be seen first is No. 1 set screw
when the main shaft
is turned
in the forward direction A . For loosening, loosen No. 2 set screw first, and for tightening,
tighten No. 1 set screw
first.

No. 2 set screw

No. 1 set screw

A

No. 1 set screw

0.7mm

Procedures of assembling
1. For mounting the main shaft motor with the coupling,
(1) Tighten 4 set screws
that securing the motor, and tighten 2 set screws
on the main shaft side of the
coupling .
(2) The cords
of the main shaft motor
should be positioned in the lateral direction.
2. For connecting the coupling to the main shaft motor,
(1) Provide a clearance of 0.7 mm between the coupling
and main shaft motor .
(2) Apply No. 1 set screw
of the coupling
to the flat section
of the main shaft motor , the main
shaft
and secure it.
3. For engaging the coupling,
(1) Position the set screw
(No. 1 set screw) on the main shaft motor side between 2 set screws
on the
main shaft side, and engage the coupling.

(3) Crank rod connection/disconnection

Procedures of disassembling
1. Loosen 3 set screws
and 2 set screws . On this occasion, loosen No. 2 set screws first, and completely
disengage No. 1 set screws from the flat section of the oscillator shaft .
2. Pull out the oscillator shaft
in the direction of Arrow A.
3. Remove the main shaft
according to 3.-(1) Main shaft connection/disconnection, and remove the crank
rod unit .

22.1 to 22.6mm
Face B

No. 2 set screw

No. 1 set screw

No. 2 set screw

E

No. 1 set screw

Procedures of assembling
1. Mount the main shaft
according to 3.-(1) Main shaft connection/disconnection, and mount the crank rod
unit .
2. Adjust the clearance to 22.1 to 22.6 mm between the under cam
of the crank rod unit
and Face B
(middle metal bearing mounting face) of the frame, and secure the cam with the set screw .
(Apply No. 1 set screw to the flat section of the main shaft
and tighten it first, then tighten No. 2 set screw.
Same procedure hereafter)
3. Pass the oscillator
through the oscillator shaft , and mount them on the frame.
4. Pass the thrust collar
through the oscillator shaft . Lightly press the oscillator shaft
in the direction of
arrow C and the thrust collar
in the direction of Arrow D, and tighten 2 set screws . Make sure that No.
1 set screw touches the flat section of the oscillator shaft .)
5. Secure the oscillator
according to 3.-(11) Oscillator gear positioning.
(Caution) 1. Make sure that no torque is applied by rotating the main shaft .
2. When the crank rod unit
is connected, disconnected, or positioned, or the oscillator
is positioned, be sure to grease two specified positions and the gear section (E) of the
oscillator .
3. After positioning the crank rod unit
(under cam ), be sure to perform 3.-(11) Oscillator gear positioning. Wrong positioning of the under cam
or oscillator
may cause
frictional wear or lock-up.

10

(4) Crank balancer positioning

Standard Adjustment
[Rotating direction]
When the needle bar
lowers and the clearance between the needle bar connecting
and needle bar lower
bushing
is 4.6 mm, 2 set screws
of the crank balancer
becomes horizontal position.
[Axial direction]
Bring the main shaft eccentric cam

into contact with the crank balancer

4.6mm

11

Adjustment Procedures

Results of Improper Adjustment

If the main shaft eccentric cam is not secured, the main shaft eccentric
cam
should be positioned first.
1. Loosen 2 set screws
securing the crank balancer .
2. Remove 4 set screws , then remove the crank rod cover .
3. Turn the main shaft in the forward direction A so that the needle bar
lowers and the clearance between the needle bar connecting
and needle bar lower bushing
is 4.6 mm.
4. Secure the crank balancer
with 2 set screws
under the conditions that 2 set screws
securing the balancer
are horizontally
positioned and the balancer
is moved in the direction of Arrow B
to make it into contact with the main shaft eccentric cam . For
tightening 2 set screws , tighten them alternately.

o If the mounting angle of the crank

balancer
is wrong, vibration
during sewing will be intensified.
o If the sewing machine is used for
a long time under the condition of
wrong securing position, the life
of main shaft bearing may be
shortened.
o If the crank balancer
is not
moved in the direction of Arrow
B , it may interfere with the sewing machine frame.

12

(5) Adjustment of intermediate presser cam

Standard Adjustment

Align

Align

(6) Adjustment of intermediate presser bar

13.5mm

Standard Adjustment

13

Adjustment Procedures

Results of Improper Adjustment

1. Align the edge of the intermediate presser cam

with the center of
the engraved point on the main shaft , align the engraved line on
the intermediate presser cam
with the engraved point on the main
shaft , and tighten the set screw .

o Stitch skipping and poor tense

stitch may occur.

Adjustment Procedures

Results of Improper Adjustment

1. Adjust the thrusting distance of the intermediate presser bar

to
13.5 mm, and tighten the set screw
after ensuring that the needle
passes through the center of the intermediate pressure.
(Caution) Be aware that the tightening pressure of the set screw
should be from 2.16 to 2.75 Nm (22 to 28 kgfcm).

o An excessive thrusting distance of

the intermediate presser bar
may damage the intermediate
presser spring or cause poor
presser lifting.
o Excessive tightening pressure
may deform the intermediate
pressure bar
or intermediate
presser bar connecting
resulting in malfunction.

14

(7) Intermediate presser variable connection/disconnection

Procedures of disassembling
1.
2.
3.
4.
5.
6.
7.
8.

9.
10.

27.0mm

11.

Remove the presser adjusting screw . Then, remove the intermediate presser spring
and the guide shaft.
Remove the intermediate presser auxiliary spring .
Remove the step screws , , and .
Remove the step screw .
and the variable plate
Remove the step screw , and then the intermediate presser variable plate
spacer .
Remove the step screw , and then the intermediate presser variable link .
as a
(At that time, insert a hexagonal wrench through the arm screw hole A and apply it to the setscrew
means of turn stop for the intermediate presser variable arm .)
Loosen two each of the setscrews , , and .
At that time, the second screw should be loosened first. The first screw of the setscrew should be removed,
completely separate from the flat part of the intermediate presser variable shaft .
After the intermediate presser variable arm
and the intermediate presser variable shaft
have been
and pull out the intermediate presser
pulled out in the direction of the Arrow B, loosen the setscrew
variable shaft
from the intermediate presser variable arm .
At that time, both of the setscrews
should be separated completely from the flat parts (2 positions) of the
intermediate presser variable shaft .
Loosen the two setscrews
and remove the intermediate presser coupling , the intermediate presser
motor mounting plate , and the intermediate presser motor .
and .
Loosen two each of the setscrews , ,
At that time, the second screws of the setscrews
and
should be loosened first. The first screw of the
setscrew should be removed, completely separate from the flat part of the intermediate presser lifting shaft
.
Remove the E ring
and pull out the intermediate presser lifting shaft
in the direction of the Arrow C.
193.8mm

Fig J

Right above
45

4.4mm

D
B
No. 1 set screw

0.5mm

No. 1 set
screw
No. 1 set
screw

H
C

15

Procedures of assembling
1. Fix the intermediate presser variable shaft
to the intermediate presser variable arm
by means of the
two setscrews
so that the length of the shaft section becomes 193.8mm.
(Both setscrews
should be adjusted level to the intermediate presser variable shaft .)
2. Insert the washer , thrust bearing , thrust collar , and the drive bevel gear
in the intermediate
presser variable shaft
in this order, and mount this assembly on the frame.
3. Pressing the intermediate presser variable arm
in the direction of the Arrow E, secure a proper thrust by
pressing the thrust collar
in the direction of the Arrow D and tighten the two setscrews . (Tighten the
first screw first so that it is fixed level to the intermediate presser variable shaft . Then, tighten the second
screw. To be done in the same manner hereafter.)
(Caution) If there is rattle in the variable shaft of the intermediate presser
in the forward and backward directions, this can be a cause of intermediate presser step-out. Be careful when you try
to fix the thrust collar .
4. Adjust the distance to 4.4mm between the thrust collar
and the drive bevel gear . Tighten the first
screw of the setscrew .
(Tentatively tightened till the completion of intermediate presser sensor adjustments)
5. Fix the intermediate presser motor
to the intermediate presser motor mounting plate
and mount the
intermediate presser coupling
on the motor shaft. Since then, press the intermediate presser motor
assembly in the direction of the Arrow F and tentatively fix it to the frame by means of the two setscrews .
Adjust the positioning of the intermediate presser motor assembly where the intermediate presser coupling
) can be turned without any resistance, and tighten the two setscrews .
6. Insert the sensor slit , intermediate presser lifting cam , thrust collar , and the wave washer
in the
intermediate presser lifting shaft
in this order, and pass this assembly through the frame. Mount the E
ring
on the intermediate presser lifting shaft .
7. Pressing the intermediate presser lifting shaft
in the direction of the Arrow C, press the thrust collar
in
the direction of the Arrow G and tighten the two setscrews .
8. Fix the intermediate presser lifting cam
by means of the two setscrews
so that the clearance becomes
0.5mm between both end planes of the intermediate presser lifting cam
and the intermediate presser
lifting link .
9. Turn the intermediate presser variable shaft
and the intermediate presser lifting shaft
so that the
trailing bevel gear
and the drive bevel gear
are positioned as shown in Fig. J. Since then, fix them by
means of the two setscrews
while the trailing bevel gear
is pressed in the direction of the Arrow G (in
order to reduce the backlash to zero).
10. Press the sensor slit
in the direction of the Arrow C and turn the setscrew
so that its H comes in the
section toward the setscrew
of the intermediate presser lifting cam . Then, fix H of the setscrew
tentatively.
11. According to adjustments of intermediate presser variable as described in 3-(8), make adjustments of intermediate presser variable and fasten the setscrews of the drive bevel gear
and the sensor slit .
12. Using the step screw , mount the intermediate presser variable link
on the intermediate presser variable arm .
and the variable plate spacer .
13. Using the step screw , mount the intermediate presser variable plate
14. Mount the step screws , , and .
15. Using the step screw , mount the intermediate presser variable link
on the intermediate presser variable plate .
16. Mount the intermediate presser auxiliary spring .
17. Mount the intermediate presser spring
and the guide shaft from above the frame. Then, mount the
presser adjusting screw .
(27.0mm from the upper plane of the arm to that of the presser adjusting screw )

16

(8) Intermediate presser variable adjustments

Standard Adjustment
Start the Test Mode I10 (IP-400) or CP-8 (CP-20) and press
twice after the completion of origin retrieval.
At that time, there shall be coincidence between the center of the arms left-side hole C and the second screw
of the intermediate presser variable arm .

17

Adjustment Procedures

Results of Improper Adjustment

1. Start the Test Mode I10 (IP-400) or CP-8 (CP-20).

2. Tread on the start pedal for origin retrieval, and make adjustments by
turning the sensor slit
so that the lines combining the center of the
intermediate presser lifting shaft , the standard hole of the intermediate presser lifting cam , and the center of the cam follower
become almost a straight line.
3. Press
of the panel three times. Loosen the first screw
of the
drive bevel gear
of the intermediate presser variable shaft .
Take out the drive bevel gear
from the flat part of the intermediate
presser variable shaft
and move it in the direction of the Arrow A.
4. Using the [+] key or the [] key, turn the intermediate presser variable
shaft
until the second screw
of the intermediate presser variable arm
settles in the center of the arms left-side hole C. (Insert
a hexagonal wrench to adjust positioning so that the arm comes in
the center of backlash deflection.)
5. Turn the intermediate presser lifting shaft
so that the second screw
of the intermediate presser lifting cam
comes just above. Press
the drive bevel gear
of the intermediate presser variable shaft
in the direction of the Arrow B to fix it.
6. After the completion of second origin retrieval, press
of the
panel twice to secure the [timing adjustment position]. In this case,
confirm that the second screw
of the intermediate presser variable arm
is positioned in the center of the arms left-side hole C or
below it. (If the screw seems to have been positioned above the center, return to Step 4 and repeat the above-mentioned adjustments.)
7. If the second screw
of the intermediate presser variable arm
is
not positioned in the center (or lower), loosen the setscrew
of the
and turn this sensor slit
in the direction of the Arrow
sensor slit
A for fine adjustments.
8. Make origin retrieval and confirm that the the cam follower
is located in the parallel section of the intermediate presser lifting cam
. When the condition has been found normal, fasten the setscrew
of the drive bevel gear
and the setscrew
of the sensor slit
regularly.
(Caution) For the prevention of the sensor
from destruction,
make origin retrieval after confirming that the slit of the
sensor slit
is positioned in the center of the sensor
.

o There will be a displacement

between the variable value of the
intermediate presser lower
position and the panel setup
value.
in
o If there is no cam follower
the parallel section of the intermediate presser lifting cam
at the
time of origin retrieval, stepping
out may occur in the intermediate
presser motor, thus causing defective stitches, generation of
sound from the face plate section,
and destruction of parts.
o If adjustments of backlash are insufficient for the drive bevel gear
, stepping out may occur in the
intermediate presser motor, thus
causing defective stitches, generation of sound from the face
plate section, and destruction of
parts. .

18

(9) Intermediate presser drive arm

Standard Adjustment
* Refer to Instruction Manual, 4-7. Intermediate presser height.

Approx 3.6mm

Close contact

Intermediate presser bar

19

Adjustment Procedures

Results of Improper Adjustment

1. Turn ON the power supply and set the height of the intermediate
presser
to 0mm. Turn OFF the power supply in the state that the
intermediate presser
has been lowered.
2. Loosen the intermediate presser stroke adjusting screw .
3. Turn the pulley and move the needle bar to the lower dead point.
When the intermediate presser is lifted and the intermediate presser
stroke adjusting screw
is moved to the right or left, confirm that
the intermediate presser adjusting arm
is positioned not to move
vertically and that the intermediate presser positioning link
keeps
a close contact with the arm. In this state, tighten the setscrew
of
the intermediate presser drive arm.
(The clearance is approximately 3.6mm between the intermediate
presser needle bar connection and the intermediate presser bar metal
.)
4. After the setscrew
has been tightened, confirm that there is no
backlash in the intermediate presser adjusting arm
in the forward
and backward directions.
5. Finally, make adjustments of the intermediate presser stroke.
(Refer to Instruction Manual III. MAINTENANCE OF SAWING MACHINE, 1-4. Adjusting the vertical stroke of the intermediate presser.)

o If there is no clearance, there will

be interference between the
intermediate presser bar metal
and the intermediate presser
needle bar connection during
sewing machine operation, and
this will generate abnormal sound
as a result.
o If there is too much clearance,
there will be interference between
the intermediate presser adjusting arm
and the arm during
sewing machine operation, thus
generating abnormal sound as a
result.
o If there is too much or too less
clearance, the lower dead-point
height of the intermediate presser
may be changed as a result of
intermediate presser stroke adjustments.

20

(10) Lower shaft backlash adjustment and connection/disconnection

Standard Adjustment
1. Size of lower shaft backlash is 0.1mm at the tip of the driver . The shaft is required to rotate smoothly.
2. Define the stop position of the lower shaft
so that the set screw
settles almost in the center of the flat
section
of the lower shaft .

0.1mm or less

Face A

(11) Oscillator gear positioning

Standard Adjustment
1. When the oscillator is lightly swung by a finger in the direction of the arrow, the oscillator
center position of swinging.
No. 2 screw

No. 1 screw

No. 1 screw

21

is fixed in the

Adjustment Procedures

Results of Improper Adjustment

1. Lower shaft backlash

1) Loosen the two set screws .
2) Turn the lower shaft rear metal in the direction of the arrow and adjust
the backlash, keeping the metal to contact closely with Face A.
Size of backlash is 0.1mm at the tip of the driver . The shaft is
required to rotate smoothly.
3) Tighten the two set screws .

o If the backlash is excessive, the

hook noise will be increased.
o If backlash is too small, the lower
shaft gear
or the oscillator
will give rise to frictional wear. In
addition, this can be a cause of
crank rod lock-up.
o If the front or rear position of the
lower shaft rear metal
is displaced at the time of backlash
adjustment, this can also be a
cause of the lock-up of oscillator
or the crank rod.

(Caution) When eliminate the backlash, the direction of rotation

should always be kept in the direction of the arrow.
2. Lower shaft connection/disconnection
1) Loosen the two set screws .
2) The lower shaft
can be taken out if it is pulled in the direction C
of the arrow.
3) When mounting the lower shaft , insert it in the lower shaft rear
metal
and the lower shaft gear . Apply one of the set screws
to the flat section
of the lower shaft
and tighten it approximately in the center. Tighten the remaining set screw .
* Connection and disconnection of the lower shaft
become easy if
the above-mentioned backlash has been relieved in advance. In this
case, backlash adjustment must be done after the lower shaft
has
been installed.

Adjustment Procedures

Results of Improper Adjustment

1. Loosen the two set screws

and increase the backlash of the lower
shaft gear .
(Caution) 1. If the lower shaft gear
has insufficient backlash,
the oscillator
does not swing correctly. In such a
case, refer to [(10) Lower shaft backlash adjustment
and connection/disconnection] and provide a sufficient backlash.
2. The three set screws
should have been loosened in advance. In
this case, the second screw of the set screws
should be loosened
first. Then, the first one can be loosened.
3. Lightly swing the whole body of the oscillator
with a finger in the
direction of the arrow. Decide the positioning of the oscillator
so
that it stays in the center of swinging.
4. Loosen the three set screws
and then fix them so that the oscillator
is not displaced from the center of swinging.
(Tighten the first screw first so that it comes in contact flatly with the
oscillator shaft . Then, tighten the second one.)
5. Make backlash adjustment for the lower shaft gear , according to
[(10) Lower shaft backlash adjustment and connection/ disconnection].
(Cautions) 1. In the case of disassembly and adjustment, greaseup treatment is always needed for the specified
places (2 positions) and the gear area A of the oscillator .
2. When the crank rod (under-cam) is removed, actions
for under-cam positioning must be taken, without fail.
Refer to [(3) Crank rod connection/ disconnection].

o If the position for fixing the

oscillator
is inadequate, this
can also be a cause of the
frictional wear or lock-up of the
oscillator pin, crank rod lid, undercam, and the crank rod.

22

(12) Adjustment of hook oil amount

Standard Adjustment

(13) Shuttle connection / disconnection and oil wick piping

Procedures of disassembling
1.
2.
3.
4.
5.
6.
7.
8.

Loosen the three set screws .

Cut the harness bands .
Remove the set screw
and pull the oil tank
in the direction of the arrow A.
Pull Part B upwards of the two lubrication pipes
and . Take them out of the oil tank
Release the clamp
of the oil drain pipe .
Loosen the set screw
and take out the driver .
Loosen the set screw .
Remove the set screw
and pull out the shuttle race adjust shaft
.
9. Pull the shuttle
in the direction of the arrow C and take it out.

D
E
A

23

Adjustment Procedures
1. Loosen the set screw

Results of Improper Adjustment

and remove it.

2. When the adjusting screw

is tightened, the quantity of oil can be
regulated for the lubrication pipe left .
3. After adjustments, tighten the set screw

o If the amount of hook lubricant is

reduced too much, this can be a
cause of frictional wear of the
hook race plane or lock-up.

to fix it.

(Cautions) 1. In the state of standard shipping, the hook lubricais positioned so that it is lightly tighttion reducer
ened and then return-loosened by 4 turns.
2. When reducing the oil amount, the screw should not
be tightened up fully. Tighten the hook lubrication
reducer
and then return it by two turns. In this
position, wait for half a day to see how it goes. Too
much reduction can be a cause of hook wear.

Procedures of assembling
1. Pass the two lubrication pipes
.

and

and the oil drain pipe

through the frame, and mount the shuttle

2. Pass the lubrication pipe

along the upper side of the oil drain pipe . Hold the lubrication pipe
with the
pipe holder
and fix it with the set screw .
At that time, make sure not to let the lubrication pipe
and the oil drain pipe
come in contact with the
thread cutter connector rod and the lower shaft.
3. Fix the lubrication pipe
to the bed by means of the harness band .
4. Fix the two lubrication pipes
and
with the cord clamps
and the set screws .
At that time, make sure not to permit the lubrication pipes
and
to come in contact with the needle thread
clamp connector link.
5. Insert the two lubrication pipes
and
in the oil tank
and fix this oil tank
to the frame with the set
screws .
6. Fix the needle thread clamp sensor cord and the oil drain pipe
with the cord clamp .
At that time, pass the oil drain pipe through the head holes in two positions D and E.
7. Insert the oil drain pipe
in the oil reservoir .
8. Fix the shuttle
and mount the driver
with the set screw . Refer to [(15) Hook adjustment].
* Harness bands

: Part No. EA9500B0100

24

(14) Adjusting the height of the needle bar

Standard Adjustment

: Marker line for DP x 5

: Marker line for DP x 17
(with needle count higher than #22)

: Marker line for DP x 17

(with needle count lower than #22)

25

Adjustment Procedures

Results of Improper Adjustment

* Turn ON the power once, and turn OFF the power again after
making the intermediate presser in the lowered state.
1. Bring the needle bar
down to the lowest position, loosen the needle
bar connection screw
and align the upper engraved line
on the
needle bar with the bottom end of the needle bar lower bushing .
2. Change the adjusting position according to needle sizes.
(Caution) Be sure that torque is even after adjustment.

26

(15) Hook adjustment

Standard Adjustment

: Marker line for DP x 5 needle

: Marker line for DP x 17 needle
(with needle count higher than #22)
: Marker line for DP x 17 needle
(with needle count lower than #22)
DP x 17 needle
When a DP x 5 DP x 17 needle
needle is used (of which needle (of which needle
count is higher
count is lower
than #22) is used. than #22) is used.

0mm

0mm

0.5mm

0.05 to 0.1mm

7.5mm

27

Adjustment Procedures

Results of Improper Adjustment

* Turn ON the power once, and turn OFF the power again after
making the intermediate presser in the lowered state.
1. Turn hand wheel by hand to ascend the needle bar .
Adjust so that lower marker line
on the ascending needle bar aligns
with the bottom end of the needle bar bushing lower .
2. Loosen setscrew
in the driver. Drawing bobbin case opening lover
hook
toward you, open it to the right and left until bobbin case
opening lover
comes off.
come off
(Caution) At this time be careful not to let inner hook
and fall.
3. Refer to 5. below and make tentative adjustments of timing for the
inner hook .
4. Turn the pulley by hand and make adjustments for the needle location block of the driver
by bending it in the direction of Arrow A so
that the clearance b attains 0mm to 0.5mm between the needle tip
and the lowest end of the needle location block of the driver
when
the needle tip of the inner hook
is protruded by 0.5mm from the
right end of the needle .
5. Make an adjustment so that the blade point of the inner hook
is
aligned with the center of the needle , and that the clearance between the front end of the driver
and the needle
is 0 mm because the front end of the driver
receives the needle to prevent
needle bending. Then, tighten the set screw
securing the driver.
6. Make adjustments so that the clearance (C) in the revolving direction
attains 0.3mm to 0.6mm between the inner hook
and the driver
by bending the inner hook holder block (reverse side of the needle
location block) of the driver
in the direction of the arrow (D).
(Caution) Make sure not to damage the shuttle
race plane while
making adjustment of the driver .
7. Loosen the set screw
securing the shuttle , and adjust the frontrear position of the shuttle by rotating the shuttle adjusting shaft
so that the clearance between the needle
and the blade point of
the inner hook
becomes 0.05 to 0.1 mm.
8. After adjusting the front-rear position of the shuttle , set the clearance between the needle
and the shuttle
to 7.5 mm by adjusting the rotating direction, and tighten the set screw
securing the
shuttle.

28

(16) Thread trimmer presser lifter cam connection/disconnection

Procedures of disassembling
1. Loosen 2 set screws

securing the presser lifter and thread trimmer cam (hereafter called cam)

2. Loosen the two set screws

and remove the sensor slit

3. Remove the four set screws

and take out the presser lifting motor
in the direction of the arrow. In some
cases, the bearing
and the motor shaft seem to be tightly coupled. Pull out the motor shaft in the direction
of the arrow straightforward in order not to hurt the bearing .
At that time, the cam
may come down. Handle it with care, not to damage it.

Flat section

(17) Thread trimmer and presser origin sensor adjustment

Standard Adjustment
When origin retrieval (at start switch on) is conducted in the test mode I07 (IP-400) or CP-6 (CP-20), the
standard holes of the sewing machine frame ( A and B ) are aligned with the standard hole C of the thread
trimmer and presser lifter cam .

D
B
C
A

29

Procedures of assembling
1. Apply a proper amount of grease (Juki Grease A) to the grooved cam block of the cam , the peripheral cam
block, and the rollers of the presser bar lifter link
and the thread trimmer link . Refer to 10.-(4) Parts to
which grease lock-tight is applied o TENSION RELEASE & THREAD TRIMMER MECHANISM
COMPONENTS.
2. While the cam
is being inserted in the shaft of the presser lifting motor , mount the assembly on the
sewing machine frame and tighten the four set screws . The insertion of the cam should be done gently in
order not to hurt the bearing .
and Clearance A toward the thread trimmer link
should be
3. Clearance B toward the presser bar lifter link
equally distributed. For this purpose, adjust the position of the cam
and fix it with the use of the two set
screws . (Apply the screws to the flat section at both ends of the shaft.)
* If it is difficult to examine Clearance B, Clearance A should be adjusted to 0.5mm ~ 0.7mm during assembly.
4. Mount the sensor slit
with the two set screws
so that the end plane of the motor shaft can approximately coincide with that of the sensor slit . (Join the flat section for installation.)
* Confirm that the slit plate of the sensor slit
does not interfere with the presser bar lifter sensor.
5. Refer to 3.-(17) Thread trimmer and presser origin sensor adjustment and make sensor adjustments.

Adjustment Procedures

Results of Improper Adjustment

1. Start the test mode I07 (IP-400) or CP-6 (CP-20).

2. Tread on the pedal for the retrieval of the thread trimmer and presser
bar lifter (cam) origin.
3. Make sure that the standard holes ( A and B ) of the thread trimming
motor stand are aligned with the standard hole C of the thread trimusing a bar .
mer and presser lifter cam
4. If the standard hole C of the thread trimmer and presser lifter cam
is too high ( E direction), loosen the set screw
and move the sensor mounting plate
upward ( E direction) and secure it.
If the standard hole C of the thread trimmer and presser lifter cam
is too low ( D direction), loosen the set screw
and move the
sensor mounting plate
downward ( D direction) and secure it.
After securing the sensor mounting plate , conduct origin retrieval
by pressing the pedal to make sure that the standard holes are aligned.
5. Repeat the above steps 2 to 4 until the coincidence is confirmed.
(Caution) Tighten the set screw
after confirming that there is no
interference between the sensor slit plate and the sensor.

o If the standard holes are not

aligned, the thread trimming
timing error occurs and defective
thread trimming and unthreading
at the beginning of sewing may
be caused.

30

(18) Adjusting the thread trimmer sensor

Standard Adjustment
After completion of origin retrieval (at start switch on) in the test mode I07 (IP-400) or CP-6 (CP-20), press the
+ key
6 to 8 times, and the thread trimmer sensor is turned off (IP-400: The contents
on the operation
panel change from
to
, CP-20: The display
of 10th digit on the operation panel changes from
1 to 0.)

CP-20

31

Adjustment Procedures

Results of Improper Adjustment

1. Start the test mode I07 (IP-400) or CP-6 (CP-20).

2. Tread on the pedal to perform origin retrieval for the thread trimmer
cam.
(Confirm that the origin is in the correct position. Then, proceed to
the procedures shown below. Refer to (17) Thread trimmer and
presser origin sensor adjustment.)
(IP-400) or
(CP-20). Make sure that the con3. Press the + key
tents
(IP-400) on the operation panel change from
to

or that the value

(CP-20) on the operation panel changes from
11 to 01 after pressing the + key 6 to 8 times.
4. If the change occurs by pressing the + key other than 6-8 times, or
the change does not occur, loosen the set screw
and adjust the
sensor slit
finely in the arrow direction.
5. After the sensor slit
has been fixed, tread on the pedal and make
origin retrieval for the thread trimmer cam. Examine the sensor
changeover position in the steps 3. and 4. above.
6. Repeat the steps 2. ~ 5. above until the coincidence is secured.
(Caution) During adjustments, check the clearances A, B, and C of
and the sensor . If the clearances
the sensor slit
seem to be insufficient, use the set screws
and
to
correct the gradient. While taking this action, continue
to work on the steps above.

32

o If the thread trimmer sensor

changeover takes place outside
the range, the moving knife may
interfere with the needle. This will
be a cause of injury or the
breakage of parts.
o If the thread trimmer sensor
changeover does not take place,
Error 305 occurs and the sewing
machine fails to start operating.
o If the sensor slit
has no clearance against the sensor , this
can be a cause of destruction in
the sensor slit
or the sensor
.

(19) Adjustment of the moving knife and counter knife position

Standard Adjustment
Counter knife position : The clearance between the counter knife
and the needle hole guide
is 1.0mm.
Moving knife position : Before thread trimmer operation (standby state), the distance from the throat plate
front end to the tip of the thread cutter lever (small)
is 18.5mm.
However, there shall be a proper clearance toward the moving knife tip during needle
thread clamp and feed forward.
There shall be a
clearance
18.5mm
1.0mm
18.5mm

(20) Floating amount of the thread tension disk

Standard Adjustment
When the sewing machine power supply is turned off (AT solenoid
tension disk
is 0.6 ~ 1mm.

is OFF), the gap between AT thread

Close contact

0.6 to 1mm
4 mm or less

33

Adjustment Procedures
1. Counter knife position
Loosen the counter knife set screw

Results of Improper Adjustment

o If the clearance is less than
1.0mm, thread may be cut by the
counter knife
blade when the
thread is pulled with the moving
knife . In this case, upper and
lower threads are cut into short
pieces.
o If the clearance is more than
1.0mm, the residual thread length
after thread cutting operation becomes longer beneath the work.

to adjust the position.

2. Moving knife position

Loosen the screw
to adjust the position.

Adjustment Procedures

Results of Improper Adjustment

1. Turn off the power supply and look for any close contact between the
AT solenoid
and the thrust collar .

o If the amount of disc floating is too

less, the residual thread length
can be changed or shortened
when the thread is thick.

2. Loosen the three set screws

.

and remove the thread tension cap

3. Hold the tension releasing pin adjust collar

loosen the nut .

not to let it rotate, and

4. Turn the tension releasing pin adjust collar

and adjust the gap
between the thread tension disk . (Adjustment of thread tension
disc floating)
5. Hold the tension releasing pin adjust collar
and tighten the nut
Mount the thread tension cap
by means of the set screw .

6. Turn on the power supply and set up the thread tension. Confirm that
the thread tension disk
are closed.
is
(Caution) When the tension releasing pin adjusting collar
rotated, the thread section should not be engaged with
the incomplete thread section of the thread tension releasing pin . (The thrusting distance of the thread tension releasing pin
should be 4 mm or less from the
tension releasing pin adjusting collar .)
* If the amount of disc floating cannot be adjusted properly under the condition that the thrusting distance is
4 mm or less, loosen the set screw
and adjust the
AT link unit (front) in the right-left direction.
Refer to (22) AT unit connection/disconnection.

34

o If the amount of disc floating is too

much, the thread tension discs
cannot close completely and normal thread tension may fail to be
chosen. This can be a cause of
imperfect sewing.
o If the thread section of the tension
releasing pin adjusting collar
is engaged with the incomplete
thread section of the thread tension releasing pin
, the thread
tension releasing pin
may be
damaged.

(21) Second thread tension connection / disconnection

Procedures of disassembling
1. Loosen the set screw

2. Remove three setscrews

and take out the thread tension cap

3. Remove the nut

and the tension releasing pin adjusting collar . Then take out the thread tension disc
pressing plate
and three thread tension disc return springs .
4. Pull out the second thread tension

to remove it. (Arrow

5. For reassembly, follow the steps of 4. to 1. above.

35

Procedures of assembling
1. When mounting the second thread tension , confirm in advance that the pin block
of the AT link unit
(front)
is exactly settling in the hole of the thread tension pressing pin . If you try to mount the second
thread tension
forcedly with the pin area left disengaged, this may result in breakage in the thread tension
pressing pin
or malfunction.
2. After the completion of mounting, make adjustments of (20) Floating amount of the thread tension disk and
(39) Adjustment of thread take-up spring; 1) Stroke adjustments.

36

(22) AT unit connection / disconnection

Procedures of disassembling
1. Remove the set screw
of the AT link unit (front)
and take out the second thread tension
to Second thread tension connection / disconnection.)
2. Draw out the cotter pin
not to drop the washer

from the pin block

at that time.

(H type) or

(S type) of the AT link unit (rear)

3. Lift the AT joint block

of the AT unit upward to remove the block from the pin block
type) of the AT link unit (rear) .
4. Draw out the AT link unit (front)
5. Remove the two set screws

from the plane side (in the direction of the arrow

and take out the AT solenoid unit

6. For reassembly, follow the steps of 5. to 1. above.

Close contact

37

. ((21) Refer
. Be careful

(H type ) or
) and remove it.

(S

Procedures of assembling
1. For incorporating the AT solenoid unit
into the system, run the solenoid cable
from the rear of the AT
solenoid unit to the rear end of the machine arm.
2. The center-to-center distance between the AT joints
of the AT connector rod
is 299 mm for S type and
301 mm for H type.
When the AT joints
are disassembled or assembled, make sure that the center-to-center distance is
correct, and that the front and rear of the AT joints
are parallel. Failure to observe this may cause AT
malfunction resulting in incorrect thread tension.
(When the AT joint
is turned 4 times, the feed move amount comes to attain 2mm.)
3. For the pin block of the AT link unit (rear) , use the pin block
for H type and the pin block
for S type.
The wrong pin position may cause AT malfunction resulting in incorrect thread tension.
4. After completion of all assembly work, make sure that the thrust collar
closely contacts with the AT solenoid unit . If there is a clearance between them, loosen 2 set screws
and move the AT solenoid unit
to the rear (Arrow F ) and secure it again.
* If the above-mentioned center-to-center distance is great between the AT joints , the clearance will be
opened wider.

Close contact

S type: 299mm, H type: 301mm

Secure parallelism between plane and plane.

38

(23) Wiper adjustment

Standard Adjustment
1. When lowering the intermediate presser at the stop position after thread trimming (needle
height from
the top surface of throat plate is 17.7 mm.) and pressing wiper link section A , adjust the clearance
between the center of needle
and the inside of V letter of the wiper
to 10 mm.
2. Press wiper link section A on the way and when the wiper
has come to the underside of needle, adjust
the clearance to 1 mm.
3. The opening angle of the top end of the wiper
is 15 to 20.
A

1mm

Wiper shaft cap

Throat plate top surface

15 to 20

Height of
Intermediate
Presser

10mm

Center of needle

V letter

(Caution) The intermediate presser supplied as standard accessory is available up to 5 mm

material thickness.
However, the intermediate presser can not be used for the 3 mm material thickness
or more since the wiper can not pass the space between the tip of needle and the
intermediate presser.
Turn OFF the wiper switch in case of 3 mm material thickness or more.

39

Adjustment Procedures

Results of Improper Adjustment

1. Turn OFF the power after stopping the thread trimming, or turn ON
the threading switch and lower the intermediate presser .
(Caution) As for the height of needle
when adjusting the wiper
, set the height when the sewing machine stopped after trimming the thread actually.
2. Push wiper link section A and move the top end of the wiper
to
the under side of the needle.
3. In the state of the above item 2. , loosen setscrew
and adjust the
clearance between the wiper and the tip of the needle should be (1
mm) and the opening angle should be (15 To 20). Then tighten
setscrew
.
4. Push wiper link section A to the last and loosen setscrew
.
5. In the state of the above item 4. , adjust the longitudinal (10 mm) and
lateral positions of the wiper . Then tighten setscrew
.

o If the clearance between the wiper

and needle
is too small, the
wiper comes in contact with the
needle
due to uneven stop
position of the main shaft, causing
needle breakage.
o If the clearance between the wiper
and needle
is excessive,
the wiper comes in contact with
the intermediate presser
and
the wiper will damage the intermediate presser . Also, the intermediate presser
can not go
up.
o If a clearance of 10 mm between
the inside of V letter of the wiper
and the center of needle
is
mistakenly set, the wiper fails to
spread the thread.
o Similarly, If the center of needle
does not align with the V letter of
, the wiper fails to
the wiper
spread the thread.
o If the opening angle of the wiper
is excessive, thread sweeping
failure will occur.

40

(24) Adjusting the pre-load of the X-Y table

Standard Adjustment
When removing the X-Y table assy
the X axis only.

from the sewing machine, re-adjustment of the pre-load is necessary for

Bed

9.8 to 39.2N

41

Adjustment Procedures

Results of Improper Adjustment

1. Hold down the X fixed race (rear)

in the direction of the arrow to
tighten 4 set screws .
2. Loosen 4 set screws .
3. Hold down the X fixed race (front)
in the direction of the arrow to
tighten 4 set screws . * Then, adjust the retainer compensating
torque between 9.8 to 39.2 N (1 to 4 kgf) on both right and left sides.
4. Tighten 4 set screws .
* Retainer compensating torque: This is a load necessary to move the
race table
after the retainer
has come in contact with the X
stopper .
This torque should be measured when the belt is slack before pulse
motor installation.

42

(25) Adjustment of the tension of the X timing belt

Standard Adjustment

4mm

er
nt
Ce

7.84N

(26) Adjustment to positions of X-motor and Y-motor (Backlash adjustment to gear)

Standard Adjustment
1. Hold down the X motor
2. Hold down the Y motor

in the direction of Arrow A and secure it.

in the direction of Arrow B and secure it.

A
B

43

Adjustment Procedures

Results of Improper Adjustment

1. Move the race table

to the left end (in the direction of the arrow).
2. Tighten the adjusting screw
and fix the nut
so that the load
point makes a warp of 4mm when a load of 7.84N (800gf) measured
by a spring balance is applied to the timing belt .
3. Tighten the set screw
and check the amount of deflection again.

o If the tension is excessive, it will

cause timing belt
breakage.
o If the tension is too low, it will
cause failure of the feed.

Adjustment Procedures

Results of Improper Adjustment

1. Loosen 4 set screws

securing the X motor .
2. Hold down the X motor
in the direction of Arrow A and tighten 4 set
screws
to secure the X motor .
3. Loosen 2 set screws , 2 set screws , all of which secure the Y
motor , and 2 set screws
securing the Y motor mounting plate
.
4. Hold down the Y motor
in the direction of Arrow B and tighten 2 set
screws
that are positioned upper. Then, tighten 2 set screws
that are positioned lower and 2 set screws
securing the Y motor
mounting plate .

o If the X motor or Y motor is held

down inadequately, feeding gear
backlash is increased and needle
location accuracy may be
reduced. In addition, feeding error
may be caused resulting in needle
breakage, and other problems.
o If the pushing is excessive, the
load of the feed will become large,
causing the failure of the feed.

44

(27) Adjusting of the presser lower arm (Motor type only)

0.3mm

Standard Adjustment

Close contact

Close contact

(28) Adjustment when the presser plate sheet is replaced (Motor type only)
Standard Adjustment

Unevenness: No good

Apply grease

45

Adjustment Procedures

Results of Improper Adjustment

1. Secure the presser lower arm A so that the clearance between the
holding arm and machine arm becomes 0.3 mm with 2 set screws
.
2. Use the adjusting screw
to make sure that the presser lower arm
A
closely contacts with the holding pin
under the condition of
the presser lifted.
3. Make the angle between the presser lower arm B
and pressing
pin
the same as the angle between the presser lower arm A
and pressing pin , and keep the machine arm to contact closely
with the presser lower arm B , and tighten the two set screws .

o If the angle of the presser lower

arm A
and B
is not equal, it
will cause loosening the arm asm.
screws or the breakage.
o If the clearance is too small between the presser lower arm A
and the arm, this can be a cause
of maloperation during pushing
down.

Adjustment Procedures

Results of Improper Adjustment

1. Put an appropriate number of the spacers

into the presser plate
to make the presser plate sheet
even.
2. In regard to the application of grease, refer to PRESSER PLATE &
MANUAL PRESSER MECHANISM COMPONENTS described in
10.-(4) Parts to which greaselock-tight is applied.

o The step difference will cause

malfunction of the feed.

46

(29) Height of the slider and pasting of the presser plate sheet (Pneumatic type only)
Standard Adjustment
1. Follow the dimensions in the drawing below for pasting the presser plate sheet
Apply grease after pasting the sheet.
2. Bring the upper end of the slider
into close contact with the presser plate .

1306, 2206

on the presser plate

Rear side of the sewing machine

2mm

21mm

2mm

1510, 2210

Rear side of the sewing machine

2mm

14mm

2mm

Presser height
adjusting screw

47

Adjustment Procedures

Results of Improper Adjustment

1. Remove 4 set screws

to remove the presser plate , and replace
the old presser plate sheet
with new one.
2. After mounting the presser plate , adjust the height of the slider
with 4 set screws . To position the height, lightly press the slider
to the presser plate
when the presser goes up.

o If the position where the presser

plate sheet
was pasted is
wrong, abrasion of related
components or peeling of the
presser plate sheet
may occur
resulting in a feed error due to
direct contact between the slider
and presser plate .
o Wrong slider height may cause
a feed error.

48

(30) Adjusting the speed of the work clamp feet (Pneumatic type only)
Standard Adjustment
1. Adjust the knob 1
and the knob 2
of the speed controller
mounted on the solenoid valve and make
adjustments as described below.
Presser lifting (tube label: 1-A, 2-A) and presser lowering (tube label: 1-B, 2-B).
Loosen the knob 2
and turn the knob 1
once fully to the right in order to make 3 turns to the left.
Since then, tighten the knob 2 .

49

Adjustment Procedures

Results of Improper Adjustment

1. Adjust the speed referring to Standard Adjustment.

2. To increase the speed of lowering/raising the work clamp foot, turn
the knob 1
counterclockwise.
3. To decrease the speed, turn the knob 1
clockwise.

o When the work clamp foot comes

down, the noise is big.
o The work clamp foot fails to rise.

50

(31) Making the origin setting gauge

16 mm
36 mm

Tap M4 for setscrew

63.5 mm

Hole 4 for
positioning pin

43.5 mm

87.5 mm

107.5 mm

Standard Adjustment

Origin marking for 1316 , 2206

Origin marking for 1510 , 2210

(32) Adjusting the X origin sensor

Standard Adjustment
When the feed is in the mechanical origin, align the tip of the needle with the lateral position of the engraved dot
of the origin.

D
A
C

51

Adjustment Procedures
1. Make an origin setting gauge
to the work clamp foot .

Results of Improper Adjustment

as shown in the figure, and attach it

Adjustment Procedures

Results of Improper Adjustment

1. Start the test mode I06 (IP-400), or CP-2 (CP-20).

2. When the star pedal is depressed, the feed moves to the mechanical
origin and stops.
3. Lower the needle and check the right and left displacement based on
the engraved marking of the origin.
4. When the engraved marking of the origin is found to be displaced in
Direction A from the needle tip, loosen the two set screws
and
adjust the sensor mounting plate
in Direction C. After adjustments,
tighten the two set screws .
5. When the engraved marking of the origin is found to be displaced in
Direction B from the needle tip, loosen the two set screws
and
adjust the sensor mounting plate
in Direction D. After adjustments,
tighten the two set screws .
(Caution) After the adjustment, make sure that the slit plate does
not interfere with the sensor .

52

(33) Adjusting the Y origin sensor

Standard Adjustment
When the feed is in the mechanical origin, align the tip of the needle with the longitudinal position of the
engraved dot of the origin.

B Main motor side (rear)

A
Operator side (front)

C
D

53

Adjustment Procedures

Results of Improper Adjustment

1. Start the test mode I06 (IP-400) or CP-2 (CP-20).

2. When the pedal is trodden on, the feed moves to the mechanical
origin and then stops.
3. Lower the needle and check the front-rear displacement from the
engraved marking of the origin.
4. When the engraved marking of the origin is found to be displaced in
Direction A from the needle tip, adjust the sensor mounting plate
in Direction C. (Loosen the set screws
and fix the set screws
after adjustments.)
5. When the engraved marking of the origin is found to be displaced in
Direction B from the needle tip, adjust the sensor mounting plate
in Direction D. (Loosen the set screws
and fix the set screws
after adjustments.)

54

(34) Adjustment of the bobbin winder driving wheel position

Standard Adjustment
The distance is 139.5 mm between the measuring plane B of the bobbin winder driving wheel
cover mounting plane A of the sewing machine frame
.

and the

139.5mm
A

(35) Adjusting the bobbin winder amount

Standard Adjustment
The position of the bobbin winder lover
is based on the standard that it is 14 mm apart from the bobbin
winder shaft
. Try to perform bobbin winding actually and make fine adjustments of the bobbin lever set
screw
in the directions of the arrows A and B so that the amount of thread winding becomes adequate
(recommended value: 80 to 90% of the bobbin.)

14mm

B
A

55

Adjustment Procedures

Results of Improper Adjustment

1. Loosen the two set screws

to adjust the position (139.5mm) of the
bobbin winder driving wheel
and fix it with the two set screws .

o If the distance of 139.5mm is

insufficient, rubber ring wear may
occur in the bobbin winder unit.
In addition, the bearing life may
be reduced in the bobbin winder
unit.
o If the distance of 139.5mm is excessive, normal thread winding
may fail. In addition, this will also
cause rubber ring slippage in the
bobbin winder unit and give rise
to wear.

Adjustment Procedures

Results of Improper Adjustment

1. Loosen the set screw

of the bobbin winder lever and adjust the
distance to 14mm between the bobbin winder lever
and the bobbin winder shaft . After that, tighten the set screw
of the bobbin
winder lever.

o If too much thread is wound

(thread protruded from the bobbin
winder
), the thread
will
come in contact with the inside of
the bobbin case and this can be
a cause of sewing deficiency.

2. Start the sewing machine and wind the thread at the bobbin winder.
Confirm the amount of winding.
1) If the amount of winding seems to be too much, adjust the bobbin
in the direction of the arrow B .
winder lever
2) If the amount of winding seems to be too less, adjust the bobbin
winder lever
in the direction of the arrow A .
3. If the winding state of the thread
around the bobbin winder
seems to be uneven, loosen the nut
and adjust the height of the
thread tension control .
(Example) If the amount of the wound thread is less on the upper
side of the bobbin winder
as illustrated, adjust the
thread tension control
upwards.

56

o If the amount of thread winding is

uneven at top and bottom of the
bobbin winder , stitch perforation may become irregular.

(36) Adjustment of the shuttle upper spring and lower thread holder position
Standard Adjustment
1. Shuttle upper spring

2. Lower thread holder

: In regard to the right and left positioning, secure coincidence between the
center of the needle
and that of the groove width C. For the front-rear
positioning, join the needle rear end and the corner A block.
: The amount of overlapping with the shuttle upper spring
should be adjusted so that the thread of Vinylon #8 can pass smoothly when it is pulled
in the direction of the arrow E. After the best positioning has been secured, fasten the two set screws .

(Caution) If Part B and F is damaged, this is the cause of thread breakage, hangnail of thread, stain
on thread, etc. Therefore, this part should be polished by the use of a buff or the like. In
particular, the rear side should be handled with care.

(37) Shuttle felt

Standard Adjustment
Two pieces of the shuttle felt
are inserted in the holes of the shuttle race . Confirm that the shuttle felts
are not overloaded when the inner hook is set and turned along the shuttle race .
Shuttle packing
has been inserted in the hole of the shuttle race .

Shuttle

57

Adjustment Procedures

Results of Improper Adjustment

1. Remove the work feed bar, feed plate, and the throat plate. Adjust
the positioning of shuttle upper spring
with the set screws
(2
pcs.).
2. Using the set screw , adjust the amount of overlapping D for the
and the shuttle upper spring .
lower thread holder

o If there is a front and rear

displacement or a right and left
displacement, needle thread
biting may occur into the hook.
Too much motion to the rear side
will cause the moving knife to fail
to hook the needle thread.
o Too much motion to the rear side
will cause the moving knife to fail
to hook the needle thread.
o Too much motion to the left side
will cause the moving knife to fail
to hook the bobbin thread.

(Caution) The right and left positions can also change during (15)
hook adjustments. Position adjustment for the shuttle
upper spring
should be done after the completion of
standard hook adjustment, without fail.

Adjustment Procedures

Results of Improper Adjustment

1. If the shuttle felt

seems to be protruded or it has been replaced
with a new one, push it in by means of tweezers or the like.

o If the shuttle felt

is protruded,
this will be turned into a rotary load
of the inner hook, causing a
sewing error.
o If the shuttle felt
is missing or
pushed in too much, this will result in hook lubrication deficiency,
causing hook overheating and
wear.
o If the shuttle packing
has been
missing, the shuttle felt
and
others may be lost, and this can
be a cause of shuttle heating and
wear.

(Caution) Do not push it in excessively. Align the height and the

plane of the shuttle race .
2. Confirm that the shuttle packing

has been mounted assuredly.

58

(38) Shape of the shuttle race ring

Standard Adjustment

0.3mm

m
8m

and

Dimension A

If wear seems to be too much around the pointed tip of the inner hook, release the shuttle race ring
confirm that the dimensions of the hatched area on the rear side are 0.3 x 8mm.

(39) Adjustment of thread take-up spring

Standard Adjustment

12 to 15mm

Stroke : The movable distance of the needle thread when the needle thread is pulled in the direction A until
the thread take-up spring
stops. 12 to 15 mm for S type, 12 to 18 mm for H type.
Tension : Adjust the thread take-up spring tension in accordance with the thread tension. (Actually sew a
material and adjust the thread take-up spring tension to an appropriate value.)

When thread knots

are made.
C

Increase
Decrease

59

Adjustment Procedures

Results of Improper Adjustment

1. If the dimensions of 0.3 x 8mm are not secured, retouching is required with the aid of an oil stone.

Dimension A
(mm)

Part No.

Name of part

Remarks

0.8

14103253

Shuttle race ring A

Optional

1.3

14103352

Shuttle race ring B

Standard

1.7

14103659

Shuttle race ring C

Optional

1.9

B1817210DAD

Shuttle race ring D

Optional

Adjustment Procedures

Results of Improper Adjustment

1) Stroke adjustment
Loosen the set screw , and turn the thread tension assembly .
Turning it clockwise increases the movable distance and thread drawing amount.
2) Adjustment of thread take-up spring tension
Turn the thread tension post
using a thin driver with the set screw
tightened to adjust the thread take-up spring
tension. Turning
it clockwise increases the thread take-up spring
tension, and turn
it counterclockwise decreases the tension.
(Caution) Set the stroke of the thread take-up spring
shorter
for thin threads with thread number #50 or higher.

o If the stroke of the thread take-up

spring is larger than the specified
value:
Length of remaining needle
thread is shortened, causing the
needle thread to slip off the needle
at the sewing start.
o If the stroke of the thread take-up
spring is smaller than the specified value:
Needle thread breakage will occur at the time of thread trimming
when using a thin thread.
(Caution)
If the thread take-up spring
interferes with the L-shaped
thread guide , the thread takeup spring
may fail to return to
the initial position before thread
trimming, and the length of remaining needle thread may be
short. If such a trouble occurs,
bend the section C of the thread
take-up spring
to widen the
clearance B .

60

(40) Needle thread clamp device connection/disconnection

Procedures of disassembling
1. Remove the hinge screw .
* If the hinge screw
cannot be seen from the open part of the needle thread clamp device
move the needle thread clamp connector link
by hand in the direction of A or B.
2. Remove the four set screws
device .

, try to

of the needle thread clamp base and take out the needle thread clamp

Open part

61

Procedures of assembling
1. Push the needle thread clamp device
hinge screw .

in the direction of A and fix it with the four set screws

. Tighten the

2. Turn on the power supply and press the

key twice so that the needle thread clamp support plate
complete
is positioned at the far advanced end.
Confirm that the distance between the needle thread clamp support plate complete
and the needle
is
3.3 to 3.7mm and 1.7 to 2.3mm, respectively.
3. If the distance seems to be inadequate, loosen the four set screws
for adjustment.
device

and move the needle thread clamp

(Caution) For the prevention of injury, the distance should be checked only if the sewing LED is unlit.
(Press the
key twice after the power supply has been turned on.)

1.7 to 2.3mm

4. After the completion of the above-mentioned reassembly, make adjustments according to (41) Adjusting the
needle thread clamp sensor.

3.3 to 3.7mm

62

(41) Adjusting the needle thread clamp sensor

Standard Adjustment
When the needle thread clamp support plate complete
is withdrawn by 3 to 4 pulses from the needle thread
clamp position (Caution 1., 2.) the clearance A toward the needle thread clamp
becomes 0.
(Caution) 1. The needle thread clamp position is known as the position returned by one step from the
most advanced position when the
key is pressed after the origin retrieval by the Test
Mode I08 (IP-400) or CP-7 (CP-20).
2. According to the thread clamp specifications, the memory switch U69 may change.
S Type 0
H Type 1

1.7 to 2.3mm

3 to 4mm

63

Adjustment Procedures

Results of Improper Adjustment

In the first place, confirm that the setting value of the memory switch
U69 is [0] for S Type and [1] for H Type. Since then, make the
adjustments as specified below.

o If there are too many pulses used

until the clearance A becomes 0,
this can be a cause of unthreading
at the beginning of sewing.

1. Start the Test Mode I08 (IP-400) or CP-7 (CP-20).

2. Tread on the pedal for needle thread clamp
3. Press the
plate complete

origin retrieval.

key twice and set the needle thread clamp support

in the needle thread clamp position.

4. Confirm that the clearance A becomes 0 between the needle thread

clamp
and the needle thread clamp support plate complete
when the [] key is pressed 3 to 4 times (for 3 to 4 pulses), and that
both the needle thread clamp
and the needle thread clamp support plate complete
move together when the [] key is pressed
again.
5. If the clearance A becomes 0 with 5 or more pulses, loosen the set
screw
and fix the sensor mounting plate
after moving it in the
direction B.
If the clearance A becomes 0 with less than 3 pulses, loosen the set
screw
and fix the sensor mounting plate
after moving it in the
direction C.
After the sensor mounting plate
has been fixed, check the abovementioned steps 2. to 4.
6. Using 3 to 4 pulses, repeat the steps 2. to 5. above until the clearance A becomes 0.
origin retrieval and
7. Tread on the pedal for needle thread clamp
define the most advanced position by pressing the
key once.
8. Confirm that the distances between the needle thread clamp support
plate complete
and the needle
are kept at 3 to 4mm and 1.7 to
2.3mm, respectively.
9. If the distance is found to be inadequate, adjust the position toward
the needle
according to (40) Needle thread clamp device connection/disconnection. Since then, make the above-mentioned sensor
adjustments again.

64

o If the number of pulses is too small

until the clearance A becomes 0,
the resistance toward the needle
thread becomes large and this
can be a cause of thread breakage at the beginning of sewing.
o If the distance is improper between the needle thread clamp
support plate complete and the
needle , this will give rise to interference between the needle
thread clamp
and the needle
.

(42) Adjusting the needle thread clamp notch

Standard Adjustment
1. Needle thread clamp notch R position
When the needle thread clamp link complete
is pressed in Direction A, and Part B of the needle thread
clamp support plate complete
and the needle thread clamp
begins to open, the distance between
the needle thread clamp
and the needle thread clamp base
becomes 21mm for S Type and 16.5mm
for H type.
H Type

S Type

D
Contact

Contact

16.5mm

21mm
A

2. Needle thread clamp notch F position

When the needle thread clamp link complete
is pressed in Direction C, and Part B of the needle thread
clamp support plate complete
and the needle thread clamp
begins to open, the distance between
the needle thread clamp
and the needle thread clamp base
becomes 23mm for S Type and 21mm
for H Type.
H Type

S Type

23mm
21mm

Contact

65

Contact

Adjustment Procedures

Results of Improper Adjustment

1. Needle thread clamp notch R adjustment

1) Loosen the two set screws .
2) Press the needle thread clamp link complete
in Direction A so that
the distance between the needle thread clamp
and the needle
thread clamp base
becomes 21mm for S Type and 16.5mm for H
Type.
Move the needle thread clamp notch R
(S Type) or the needle
thread clamp notch RH
(H Type) in Direction D, lightly press it
toward the needle thread clamp cam plate , and tighten the two
setscrews .

2. Needle thread clamp notch F adjustment

1) Loosen the two set screws .
2) Press the needle thread clamp link complete
in Direction C so that
the distance between the needle thread clamp
and the needle
thread clamp base
becomes 23mm for S Type and 21mm for H
Type. Move the needle thread clamp notch F
(S Type) or the
needle thread clamp notch FH
(H Type) in Direction E, lightly press
it toward the needle thread clamp cam plate , and tighten the two
setscrews .

o If the distance is too long between

the needle thread clamp
and
the needle thread clamp base ,
the needle thread release timing
becomes earlier and this can be
a cause of unthreading at the
beginning of sewing.
o If the distance is too short between the needle thread clamp
and the needle thread clamp base
, the needle thread release timing is delayed and this can be a
cause of needle thread end remaining on the rear side of the
material.

o If the distance is too long between

and
the needle thread clamp
the needle thread clamp base ,
the needle thread release timing
becomes earlier and this can be
a cause of needle thread end remaining on the rear side of the
material or jamming of needle
thread into the needle thread
clamp .
o If the distance is too short between the needle thread clamp
and the needle thread clamp base
, the needle thread clamp timing is delayed and this can be a
cause of failure in needle thread
clamping.
o Adjustments should conform to
the adjustment values according
to the needle thread clamp specifications (S Type or H Type). Otherwise, this can be a cause of failure in needle thread clamping operation.

66

4. Memory switch
(1) Start and change
To change the memory switch (level 2):
The sewing machine operation can be changed by
changing the setting of the memory switch.

1. For IP-400:
(1) To call up the screen showing the memory switch
data (level 2) list:
Hold down the
switch for approx. 6 seconds,
and the page change button
(A) appears at the
top of the screen. Press the page change button to
call up the next page, and the memory switch (level
2) button
(B) appears. Press the memory switch
(level 2) button to call up the screen that shows the
list of memory switch data (level 2).
B

(2) To select the memory switch button to be

changed:
Select the data item (D) to be changed using the up
and down scroll buttons
(C).

(3) To change memory switch data (level 2):

Memory switch data (level 2) has 2 types of data
items: one is where a value is changed, and the other
is where a pictograph is selected. The data items
where a value is changed are colored pink and numbered such as
and the value can be changed
with + and buttons shown on the screen. The
data items where a pictograph is selected are colored blue and numbered such as
and pictographs shown on the screen where data items are
changed are selectable.
Refer to 4.-(2) Function list for further information
about memory switch data (level 2).

67

Upper 3 figures indicate a

memory switch number.

Lower 2 figures indicate

setting contents.

2. For CP-20:
1. Press the
key when the sewing LED is off to
activate the user setting mode (Level 1)of the memory
switch.
Hold down the
key for 6 seconds to activate the
service setting mode (Level 2) of the memory switch.
(Caution) A 3-second and a 6-second buzzers
sound when the key is held down. The
3-second buzzer informs users of activation of the test mode.
2. Change the memory switch number with the
keys.

and

3. Press the
key when the memory switch number
to be changed appears. On this occasion, the sewing LED is turned on.
4. Change the contents of the memory switch with the
and
keys.
5. The factory settings can be restored with the

key.

6. Press the
key to register the changes. The
sewing LED is turned off and the screen returns to
the one where the memory switch number is selected.
7. Press the
key to end the memory switch setting
mode and to return to the regular mode.

68

(2) Function list

Level 1 (Refer to the instruction manual for changing procedure.)
No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
1306
able unit

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

69

Maximum sewing speed

200 to 2700rpm

100rpm

2700

Sewing speed of 1st stitch

In case of with thread clamp

200 to 1500rpm

100rpm

1500

Sewing speed of 2nd stitch

In case of with thread clamp

200 to 2700rpm

100rpm

2700

Sewing speed of 3rd stitch

In case of with thread clamp

200 to 2700rpm

100rpm

2700

Sewing speed of 4th stitch

In case of with thread clamp

200 to 2700rpm

100rpm

2700

Sewing speed of 5th stitch

In case of with thread clamp

200 to 2700rpm

100rpm

2700

Thread tension of 1st stitch

In case of with thread clamp

0 to 200

200

Thread tension setting at the time

of thread trimming

0 to 200

Thread tension changeover timing

at the time of thread trimming

6 to 4

1 (4)

10

Sewing speed of 1st stitch

In case of without thread clamp

200 to 1500rpm

100rpm

200

11

Sewing speed of 2nd stitch

In case of without thread clamp

200 to 2700rpm

100rpm

600

12

Sewing speed of 3rd stitch

In case of without thread clamp

200 to 2700rpm

100rpm

1000

13

Sewing speed of 4th stitch

In case of without thread clamp

200 too2700rpm

100rpm

1500

14

Sewing speed of 5th stitch

In case of without thread clamp

200 to 2700rpm

100rpm

2000

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
able unit 1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

15

Thread tension of 1st stitch

In case of without thread clamp

0 to 200

16

Thread tension changeover timing

at the sewing start
In case of without thread clamp

5 to 2

70

1 (4)

0: Normal
17

Operation panel key lock mode

(CP-20 only)

18

Counter motion selection

70

19

1: X enlarging/
Y enlarging/speedItem skip
0: Sewing up
counter

(CP-20 only)

1: Bobbin thread
Down counter

Height of presser at the time of

2-step stroke

50 to 90
0: Without buzzer
sound
1: Panel operating
sound
2: Panel operating
sound + error

20

Buzzer sound can be prohibited

21

Number of stitches of thread clamp

release is set

1 to 7 (stitches)

22

Clamping timing of thread clamp can

be delayed

10 to 0

23

Thread clamp control can be

prohibited

0: Normal

1: Prohibition

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

24

Item

Feed motion timing is selected

Set the timing in direction when
stitch is not well-tightened.

Setting range

-8 to 16 (4o in steps
of, 140 to 44)

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

1 (4)

0: Presser goes up
after moving at start
of sewing
25

State of the presser after end of

sewing is selected

1: Presser goes up
immediately afterend
of sewing
2: Presser goes up by
pedal operation after
moving at start of sewing

26

71

Presser lifting motion at the end

of sewing can be set

0: With presser up
1: Wuthout presser up

27

Origin retrieval can be performed

every time after end of sewing
(other than cycle sewing)

0: Without origin
retrieval
1: With origin retrieval

28

Origin retrieval in cycle sewing can

be set

0: Without origin
retrieval
1: Every time 1
pattern is finished
2: Every time 1
cycle is finished

29

Start of presser when sewing

machine stops by temporary stop
command can be selected

0: Presser rise
1: Presser rise with
presser switch

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
changeable unit

Initial value
SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

0: Up position
30

Needle stop position is set

1: Upper dead
point
31

Thread trimming can be prohibited

0: Normal
1: Thread trimming
prohibited

32

Route of return to origin by return to

origin button can be selected

0: Disabled

1: Pattern data
reverse tracing

72

2: Origin retrieval
sewing start position
33

Bobbin winding speed can be set

800 to 2000rpm

34

Motion method of wiper can be

selected

0: Disabled

100rpm

1600

1sec

S type: 0/H type: 1

1: Enabled
35

Unit of sewing shape size change

can be selected
Function for IP-400 only

0: % input

36

Thread tension output time when

needle thread tension setting can
be set

0 to 20 (1sec)
(0: No thread
tension output)

37

Bend position of thread clamp is

selected

0: S type
1: H type thin thread
(#50 to #8)
2: H type intermediate
3: H type thick threas
(#5 to #2)

1: Actual size input

Initial value
No.

38

Item

Thread clamp and thread clamp

position selection

Setting range

Smallest
change- SS/HS SL/HL
1306
1306
able unit

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

0: Standard (front)

1: Rear
0: Disabled
39

Thread breakage detection selection

1: Enabled

40

Number of invalid stitches at the start

of sewing of thread breakage detection

0 to 15 stitches

41

Number of invalid stitches during

sewing of thread breakage detection

0 to 15stitches

73
42

Feeding frame control/pedal

open-close

(For motor-driven frame)

0: 1 step
1: 2-step stroke
(move downward to the
owest point with presser SW)
2: 2-step stroke
(start to move downward to the lowest
point with start SW)
3: 2-step stroke (With
presser SW1: mid-point,
lowermost position, rise)
4-99: 1 step
(For pneumatic frame)
0: Integrated type frame
1: Right-left separate
type frame, no preference
between right and left
2: Right-left separate
type frame, order: right left
3: Right-left separate
type frame, order: left right
4: Integrated type stroke
5: Right-left separate
type left stroke, no preference
between right and left
6: Right-left separate
type left stroke,
order: right left
7: Right-left separate
type left stroke,
order: left right
8-99: Integrated
type frame

No.

Item

Feeding frame control:

midway stop time open/close

44

Pedal SW 1 with/without latch

74

43

Setting range

(For motor-driven frame)

0: 1 step
1: 2-step stroke
(move downward
to the lowest point
with presser SW)
2: 2-step stroke
(start to move downward to the lowest
point with start SW)
3-99: 1 step
(For pneumatic frame)
0: Integrated type frame
1: Right-left separate type
frame, no preference
between right and left
2: Right-left separate
type frame, order: right left
3: Right-left separate
type frame, order: left right
4: Integrated type
frame stroke
5: Right-left separate
type left stroke, no
preference between
right and left
6: Right-left separate
type left stroke, order: right left
7: Right-left separate
type left stroke,
order: left right
8-99: Integrated type frame

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: Without

1: With
0: Without
45

Pedal SW 2 with/without latch

1: With
0: Without

46

Pedal SW 3 with/without latch

1: With

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
1306
able unit

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

0: Without
47

Pedal SW 4 with/without latch

1: With
0: Prohibition
48

Enlarging/reducing function mode

(Pattern button, CP-20:increasing/
decreasing of pitch only)

1: Stitch count
enlargement/
reduction (pitch fixed)
2: Pitch enlargement
/reduction
(stitch count fixed)
0: Prohibition

75

49

Jog move function mode

1: Parallel move
2: Second origin
specified later
0: Without motion

50

51

Retainer compensation motion:

selection of motion
Selection of needle upper dead point
at the time of origin retrievaly/ return
to origin

1: With motion
0: Without

1: With
0: Automatic
thread trimmer

52

Temporary stop, thread trimming

operation

1: Manual thread
trimmer
(by pressing
stop SW again)

No.

Item

Setting range

Smallest
changeable unit

Initial value
SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: 2700rpm/3.0mm
53

Main motor X/Y feed synchronized

control, speed/pitch

1: 2200rpm/3.0mm

2: 1800rpm/3.0mm
3: 1400rpm/3.0mm
0: Disabled
(lowering fixed)
54

Intermediate presser with/without

control

1: Enabled
(lowering with sewing
data during operation)

76

2: Enabled
(lowering during feeding
front and feeding back)

55

Intermediate presser lowering

timing

0: Immediately
before sewing
machine head
activation
1: Synchronization
with last feeding frame

56

Intermedia presser : wiper sweeping

position
(side-sweeping wiper wearing)

0: Above intermediate
presser
1: Above intermediate
presser (intermediate
presser lowest position)
2: Below intermediate
presser
0: without

57

With/without air pressure detection

1: with

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

58

Item

Intermediate presser down position

setting
Refer to Instruction Manual,
I-4-7. Intermediate presser height.

Setting range

0 to 7.0mm

Smallest
changeable unit

SS/HS SL/HL
1306
1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

0.1

3.5

0: Without
59

With/without needle cooler control

1: With

60

Greas-up error
Clearing of number of stitches of
grease-up is performed

Counted by 1 stitch
Only clear is
available.
1: Japanese

77

61

Language selection

2: English
3: Chinese

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

 Level 2
No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
able unit 1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

Motor presser presser lowering drive speed

100 to 1500pps

10pps

1500

Motor presser presser rising drive speed

100 to 3000pps

10pps

3000

Thread trimming drive speed (+ presser rising)

100 to 1500pps

10pps

1000

0: Ineffective
1: Effective
Temporary stop input selection

Thread trimming speed

78

2: Thread trimming
with temporary stop
switch or start with
start pedal after
temporary stop
0: 400rpm
1: 800rpm
0: Ineffective

Selection of thread trimming jump

feed control

1: Effective

Needle hole guide diameter at

controlling thread trimming jump feed

1.6 to 4.0mm

Thread trimmer control prohibition

selection

0: Normal operation

0.2mm

S tyoe: 1.6/H type: 2.0

1: Prohibited to use
9

Output time of magnet wiper on

10 to 500ms

10ms

50

10

Delayed time of magnet wiper off

10 to 500ms

10ms

80

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

11

Item

Wiper output timing select at upper

dead point stop

Setting range

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

SL/HL
1510

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

0: Up position

1: Upper dead point

Moving limit range in +X direction

0 to 819mm

+66

+76

+111

+111

+66

+76

+111

+111

13

Moving limit range in X direction

-819 to 0mm

66

76

111

111

66

76

111

111

14

Moving limit range in +Y direction

0 to 819mm

+31

+51

+31

+51

+31

+51

+31

+51

15

Moving limit range in Y direction

819 to 0mm

31

51

31

51

31

51

31

51

16

Selection of automatic
preparation at power on

0: Ineffective

79

12

1: Effective
17

Selection of needle bar stop

holding mode

0: Ineffective
1: Effective

18

Thread tension output while

wiper output is active

0: No output (with
thread trimming
tension kept)
1: Maximum output

19

Selection between motor presser

and pneumatic presser

0: Motor presser

1: Pneumatic presser
20

Pneumatic presser lowering delayed time

(Disabled with motor presser selected)

0 to 1000ms

21

Control of feeding frame/

automatic opening and closing

0-99: Full open,

full holding

10ms

100

No.

22

Item

Feeding frame control and

closure at sewing end
(enabled only if
lift of work
clamp foot is selected at sewing
end (=1))

Setting range

Smallest
changeable unit

Initial value
SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
1306
2206
2210
FU05 FU05

0: Full open
1: Stroke position

2 to 99: Full open

0: Nonuse

23

Selection of the fixed refuge position

1: Use

24

Origin retrieval under normal

conditions/origin reset route
selection

0: Standard
1: Inversion

80

2: Y-axis X-axis
3: X-axis Y-axis
0: Standard
1: Inversion
25

Origin retrieval at mealing/

origin reset route selection

2: Y-axis X-axis
3: X-axis Y-axis

26

Thread trimming timing

-2 to 2

27

Constant reading of pattern in

Smart Media

0: Disabled (backup
data enabled)

1: Enabled

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
able unit 1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

28

Jump command/top position rest time

0 to 100ms

10ms

20

29

Input command/timeout period

0 to 10000ms
(0: No timeout)

100ms

0: Ineffective
30

End command/stop control

1: Effective

31

Main motor XY feed synchronizing

0: Standard

control/extension
1: Extension unit

81

32

Intermediate presser lowering speed

100 to 3000pps

10pps

3000

33

Intermediate presser rising speed

100 to 3000pps

10pps

3000

0.1mm

17.0

0: Without
34

Material end detection control Y/N

1: With
0: Without

35

Inversion device control Y/N

1: With

36

Automatic inversion device Y-axis

0 to 100.0mm

37

XY inching control/first step time

100 to10000ms

10ms

400

38

XY inching control/second step time

100 to 10000ms

10ms

1200

39

XY inching control/max. speed

100 to 2000pps

10pps

1000

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
changeable unit

Initial value
SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

82

40

Fixed move-aside position, X-axis

-800.0 to 800.0mm

0.1mm

41

Fixed move-aside position, Y-axis

-800.0 to 800.0mm

0.1mm

42

XY feed move speed/origin. origin sewing start

100 to 10000pps

10pps

10000

43

XY feed speed/sewing end point sewing

start point/at work clamp foot closed

100 to 10000pps

10pps

10000

44

100 to 10000pps

10pps

2000

45

XY feed speed/sewing end point sewing

start point/at work clamp foot opened
XY feed moving speed/forward/backward

100 to 10000pps

10pps

2000

46

XY feed moving speed/return-to-origin

100 to 10000pps

10pps

2000

47

XY feed speed/retainer compensation

100 to 10000pps

10pps

2000

48

XY feed moving speed/at origin retrieval

100 to 10000pps

10pps

2000

49

XY feed moving speed/direction dependence,

first region (X-axis neighborhood)

100 to 10000pps

10pps

10000

50

XY feed moving speed/direction dependence,

second region (Y-axis neighborhood)

100 to 10000pps

10pps

10000

51

XY feed moving speed/direction dependence,

third region (45 neighborhood)

100 to 10000pps

10pps

10000

0: None
1: 2 patterns recognition
52

Bank connection selected terminal count

2: 4 patterns recognition
3: 8 patterns recognition
4: 16 patterns recognition

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

Setting range

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

0: Without
53

Presser lifting at temporary stop error Y/N

1: With
54

Prohibition selection of machine head

safety switch

0: Normal

1: Prohibition
55

Model classification

0 to 19

0/1

2/3

4/5

6/7

8/9

10/11 12/13

No. 300 to 401 items are applicable only to the simplified panel. For IP-400, the port setting screen is available for input.

83

56

300

Input terminal 1 assignment

57

301

Input terminal 1 active

0 to 199

0: LOW
1: HIGH
58

302

Input terminal 2 assignment

0 to 199
0: LOW

59

303

Input terminal 2 active

1: HIGH

60

304

Input terminal 3 assignment

61

305

Input terminal 3 active

0 to 199
0: LOW
1: HIGH

62

306

Input terminal 4 assignment

63

307

Input terminal 4 active

0 to 199
0: LOW
1: HIGH

14/15

16/17 18/19

No.

Item

64

308

Input terminal 5 assignment

65

309

Input terminal 5 active

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: LOW
1: HIGH
66

310

Input terminal 6 assignment

67

311

Input terminal 6 active

0 to 199
0: LOW
1: HIGH

68

312

Input terminal 7 assignment

69

313

Input terminal 7 active

0 to 199
0: LOW

84

1: HIGH
70

314

Input terminal 8 assignment

71

315

Input terminal 8 active

0 to 199
0: LOW
1: HIGH

72

316

Input terminal 9 assignment

73

317

Input terminal 9 active

0 to 199
0: LOW
1: HIGH

74

318

Input terminal 10 assignment

75

319

Input terminal 10 active

0 to 199
0: LOW
1: HIGH

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

76

320

Input terminal 11 assignment

77

321

Input terminal 11 active

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: LOW
1: HIGH
78

322

Input terminal 12 assignment

79

323

Input terminal 12 active

0 to 199
0: LOW
1: HIGH

80

324

Input terminal 13 assignment

81

325

Input terminal 13 active

0 to 199
0: LOW

85

1: HIGH
82

326

Input terminal 14 assignment

83

327

Input terminal 14 active

0 to 199
0: LOW
1: HIGH

84

328

Input terminal 15 assignment

85

329

Input terminal 15 active

0 to 199
0: LOW
1: HIGH

86

330

Input terminal 16 assignment

87

331

Input terminal 16 active

0 to 199
0: LOW
1: HIGH

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

88

332

Output terminal 1 assignment

89

333

Output terminal 1 active

Setting range

0 to 199

Smallest
changeable unit

Initial value
SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: LOW
1: HIGH
90

334

Output terminal 2 assignment

91

335

Output terminal 2 active

0 to 199
0: LOW
1: HIGH

92

336

Output terminal 3 assignment

93

337

Output terminal 3 active

0 to 199
0: LOW

86

1: HIGH
94

338

Output terminal 4 assignment

95

339

Output terminal 4 active

0 to 199
0: LOW
1: HIGH

96

340

Output terminal 5 assignment

97

341

Output terminal 5 active

0 to 199
0: LOW
1: HIGH

98

342

Output terminal 6 assignment

99

343

Output terminal 6 active

0 to 199
0: LOW
1: HIGH

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

100

344

Output terminal 7 assignment

101

345

Output terminal 7 active

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
1306
able unit

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: LOW
1: HIGH
102

346

Output terminal 8 assignment

103

347

Output terminal 8 active

0 to 199
0: LOW
1: HIGH

104

348

Output terminal 9 assignment

105

349

Output terminal 9 active

0 to 199
0: LOW

87

1: HIGH
106

350

Output terminal 10 assignment

107

351

Output terminal 10 active

0 to 199
0: LOW
1: HIGH

108

352

Output terminal 11 assignment

109

353

Output terminal 11 active

0 to 199
0: LOW
1: HIGH

110

354

Output terminal 12 assignment

111

355

Output terminal 12 active

0 to 199
0: LOW
1: HIGH

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

112

356

Output terminal 13 assignment

113

357

Output terminal 13 active

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
able unit 1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

0: LOW
1: HIGH
114

358

Output terminal 14 assignment

115

359

Output terminal 14 active

0 to 199
0: LOW
1: HIGH

116

360

Output terminal 15 assignment

117

361

Output terminal 15 active

0 to 199
0: LOW

88

1: HIGH
118

362

Output terminal 16 assignment

119

363

Output terminal 16 active

0 to 199
0: LOW
1: HIGH

120

364

Virtual I/O terminal 1 assignment

121

365

Virtual I/O terminal 1 I/O selection

0 to 199
0: Input
1: Output

122

366

Virtual I/O terminal 2 assignment

123

367

Virtual I/O terminal 2 I/O selection

0 to 199
0: Input
1: Output

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

Initial value
No.

Item

124

368

Virtual I/O terminal 3 assignment

125

369

Virtual I/O terminal 3 I/O selection

Setting range

0 to 199

Smallest
changeable unit

SS/HS SL/HL
1306
1306

SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: Input
1: Output
126

370

Virtual I/O terminal 4 assignment

127

371

Virtual I/O terminal 4 I/O selection

0 to 199
0: Input
1: Output

128

372

Virtual I/O terminal 5 assignment

129

373

Virtual I/O terminal 5 I/O selection

0 to 199
0: Input

89

1: Output
130

374

Virtual I/O terminal 6 assignment

131

375

Virtual I/O terminal 6 I/O selection

0 to 199
0: Input
1: Output

132

376

Virtual I/O terminal 7 assignment

133

377

Virtual I/O terminal 7 I/O selection

0 to 199
0: Input
1: Output

134

378

Virtual I/O terminal 8 assignment

135

379

Virtual I/O terminal 8 I/O selection

0 to 199
0: Input
1: Output

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

136

380

Virtual I/O terminal 9 assignment

137

381

Virtual I/O terminal 9 I/O selection

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
able unit 1306

SL/HL
1510

Initial value
SL/HL SL/HL SS/HS SL/HL
1306
2206
2210 1306
FU05 FU05

0: Input
1: Output
138

382

Virtual I/O terminal 10 assignment

139

383

Virtual I/O terminal 10 I/O selection

0 to 199
0: Input
1: Output

140

384

Virtual I/O terminal 11 assignment

141

385

Virtual I/O terminal 11 I/O selection

0 to 199
0: Input

90

1: Output
142

386

Virtual I/O terminal 12 assignment

143

387

Virtual I/O terminal 12 I/O selection

0 to 199
0: Input
1: Output

144

388

Virtual I/O terminal 13 assignment

145

389

Virtual I/O terminal 13 I/O selection

0 to 199
0: Input
1: Output

146

390

Virtual I/O terminal 14 assignment

147

391

Virtual I/O terminal 14 I/O selection

0 to 199
0: Input
1: Output

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

No.

Item

148

392

Virtual I/O terminal 15 assignment

149

393

Virtual I/O terminal 15 I/O selection

Setting range

0 to 199

Smallest
change- SS/HS SL/HL
1306
able unit 1306

Initial value
SL/HL
1510

SL/HL SL/HL SS/HS SL/HL

1306
2206
2210 1306
FU05 FU05

0: Input
1: Output
150

394

Virtual I/O terminal 16 assignment

151

395

Virtual I/O terminal 16 I/O selection

0 to 199
0: Input
1: Output
0: LOW

152

396

Pedal SW1 active

1: HIGH

91

0: LOW
153

397

Pedal SW2 active

1: HIGH
0: LOW

154

398

Pedal SW3 active

1: HIGH
0: LOW

155

399

Pedal SW4 active

1: HIGH
0: LOW

156

400

Start SW active
1: HIGH
0: LOW

157

401

Temporary stop SW active

1: HIGH

SL/HL SL/HL SL/HL

1510 2206 2210
FU05 FU05 FU05

5. Supplemental remarks of each function number and explanation of

each function
(1) Feeding frame operational sequence setup
For the AMS-210E, it is possible to change the method of feeding frame and pedal operation by means of a memory
switch.
1. Presser driving type setup
Using the memory switch K74, it is possible to set up the feeding frame of the pulse
motor driving type and the air driving type.
Setup

Contents

Explanation

Pulse motor driving

AMS210ESS/EHS-1306

Air driving

AMS210ESL/EHL-1306/1510/2206/2210

CP20: 0

CP20: 1
2. Feeding frame driving way setup
By changing the memory switches K80 and K83, it is possible to set up feeding frame and pedal operation.
(1) Automatic lowering or lifting
The memory switch K80 is used to set up the operational sequence of the feeding
frame, irrespective of pedal operation at the time of READY key ON, feeding frame
lifting with a temporary stop command in the pattern data, presser lowering key ON,
and so on.
Setup
0 to 99

Contents
All lowering, all lifting

Explanation
All lowering, all lifting only

(2) Feeding frame ON/OFF operational sequence by ordinary pedal operation

Using the memory switch U81, it is possible to set up the operational sequence of the
feeding frame by ordinary pedal operation.
In regard to the setup items, refer to the [(5) List of feeding frame and pedal setup].

(3) Feeding frame ON/OFF operational sequence by a temporary stop command

Using the memory switch U82, it is possible to set up the operational sequence of the
feeding frame by pedal operation while the feeding frame is lifted by a temporary stop
command in the pattern data.
In regard to the setup items, refer to the [(5) List of feeding frame and pedal setup].

(4) Feeding frame lifting at the end of sewing

Using the memory switch K83, it is possible to set up the feeding frame lifting position
in the returning phase from the end of sewing position (end of pattern data) to the start
of sewing position.
Setup
0
1
2 to 99

Contents
Lifting position
2-step stroke position
Lifting position

Explanation
The feeding frame is lifted to the top.
The feeding frame is lifted to the intermediate position
The feeding frame is lifted to the top.

(Caution) This function is enabled with the memory switch U37 when feeding frame
lifting has been set up at the end of sewing.

92

[(5) List of feeding frame and pedal setup]

For pulse motor driving
Setup

Contents

Preference

Explanation

United clamp

Lowered to the bottom by Pedal 1.

United clamp,
2-step stroke

Lowered to the intermediate position by Pedal 1 (right).

Lowered to the bottom by Pedal 2 (left).

United clamp,
2-step stroke

Lowered to the intermediate position by Pedal 1.

Lowered to the bottom by the start pedal to start sewing.

United clamp
2-step stroke

Lowered to the mid-point position by the first action of

the presser pedal 1.
Lowered to the bottom position by the second action.
Raised by the third action.

4 to 99

United clamp

Lowered to the bottom by Pedal 1.

For air driving

Setup

Contents

Preference

Explanation

United clamp

Lowered to the bottom by Pedal 1.

Right/left separation
clamp

Lowering enabled
from the right or left

The right feeding frame is lowered to the bottom by

Pedal 1 (right).The left feeding frame is lowered to the
bottom by Pedal 2 (left).

Right/left separation
clamp

Lowered from the

right.

The right feeding frame is lowered to the bottom by

Pedal 1 (right), then the left feeding frame is lowered
to the bottom by Pedal 2 (left). The left feeding frame
is not lowered unless the right feeding frame has been
lowered.

Right/left separation
clamp

Lowered from the

left.

The left feeding frame is lowered to the bottom by

Pedal 2 (left), then the right feeding frame is lowered
to the bottom by Pedal 1 (right). The right feeding frame
is not lowered unless the left feeding frame has been
lowered.

United clamp,
2-step stroke

Lowering enabled
from the right or left

Right/left separation
clamp,
left 2-step stroke

The right feeding frame is lowered to the bottom by

Pedal 1 (right), then the left feeding frame is lowered
to the intermediate position by Pedal 2 (left intermediate). The left feeding frame is lowered to the bottom by
Pedal 3 (left treading-on).

Lowered from the

right.

Right/left separation
clamp, left 2-step
stroke

The right feeding frame is lowered to the bottom by

Pedal 1 (right), then the left feeding frame is lowered
to the intermediate position by Pedal 2 (left intermedi
ate). The left feeding frame is lowered to the bottom by
Pedal 3 (left treading-on). The left feeding frame is not
lowered unless the right feeding frame has been lowered.

Lowered from the

left.

Right/left separation
clamp, left 2-step
stroke

The left feeding frame is lowered to the intermediate

position by Pedal 2 (left intermediate), then lowered
to the bottom by Pedal 3 (left treading-on). Since then,
the right feeding frame is lowered to the bottom by
Pedal 1 (right). The right feeding frame is not lowered
unless the left feeding frame has been lowered.

United clamp

Lowered to the bottom by Pedal 1.

8 to 99

The feeding frame is lowered to the intermediate

position by Pedal 2 (left), then lowered to the bottom
by Pedal 3 (left treading-on).

93

3. Feeding frame lifting setup at the end of sewing

Using the memory switch U37, it is possible to set up the timing for feeding frame lifting
at the end of sewing.
Setup

Contents

Explanation

After the start of

sewing reset

The feeding frame is lifted after the movement

from the end of sewing to the start of sewing.

Before the start of

sewing reset

The feeding frame is lifted at the end of sewing.

The movement is forwarded from the end of
sewing to the start of sewing with the feeding
frame left lifted.

Pedal operation after the

start of sewing reset

The feeding frame is lifted by the pedal

after the movement from the end of sewing
to the start of sewing.

CP20: 0

CP20: 1

CP20: 2
4. Feeding frame lifting setup at the time of temporary stop
Using the memory switch U41, it is possible to set up the timing for feeding frame lifting
when it has been set up with a temporary stop command in the pattern data.
Setup

Contents
Lifting

Explanation
The feeding frame is lifted immediately
with the temporary stop command.

CP20: 0
Pedal operation

Lifted by pedal operation with the temporary

stop command. Sewing is started by the start
pedal with the feeding frame left lowered.

CP20: 1
5. Feeding frame lifting prohibition setup
Using the memory switch U38, it is possible to make setting up with the feeding frame
kept lowered at all times.
Setup

Contents
Pedal operation

Explanation
It is possible to lift or lower the feeding
frame by pedal operation.

CP20: 0
Always lowered
CP20: 1

The feeding frame is kept lowered even

after origin retrieval and moving at the
sewing start. Lifting and lowering of the feeding
frame by pedal operation are also disabled.

94

6. Presser pedal setup

Using the memory switches U84 ~ U87 below, it is possible to set up the method of
pedal operation.
U84 : Used to set up the method of pedal operation for Pedal 1.
(Standard pedal, PK47 right)
U85 : Used to set up the method of pedal operation for Pedal 2.
(PK47 left intermediate)
U86 : Used to set up the method of pedal operation for Pedal 3.
(PK47 left treading-on)
U87 : Used to set up the method of pedal operation for Pedal 4.
(Not used)

Setup

Contents

Explanation

Non-latch

The feeding frame is lowered only if the

pedal is trodden on. It is lifted when the
pedal is released.

Latch

The feeding frame is lowered when the

pedal is trodden on once. It is left lowered
ven when the pedal is released. It is lifted
when the pedal is trodden on secondly.

CP20: 0

CP20: 1

95

(2) Fixed refuge position setup

Irrespective of the second origin in the pattern data, a memory switch is available to set up the second origin
(fixed refuge position) that is common to each pattern.
When the use of the fixed refuge position has been set up with the memory switch K90, the fixed refuge position
becomes enabled, which has been set up with the fixed refuge position Coordinate X of Memory Switch K117
and the fixed refuge position Coordinate Y of Memory Switch K118. In this state, the feeding frame can be ready
in the same position even though any pattern is used for sewing.
1. Selection of the fixed refuge position
Using the memory switch K90, it is possible to set up the fixed refuge position.
Setup

Contents

Explanation

Fixed refuge position

disabled

The fixed refuge position is not used.

Fixed refuge position

enabled

The fixed refuge position is used.

CP20: 0

CP20: 1
2. Fixed refuge position coordinates setup
Using the memory switch K117, it is possible to set up the fixed refuge position Coordinate X.
Setup

Contents

Coordinate X Coordinate X of the

fixed refuge position

Explanation
Coordinate X of the fixed refuge position is
set up within the feeding frame in the unit of
0.1mm.

Using the memory switch K118, it is possible to set up the fixed refuge position Coordinate Y.
Setup

Contents

Coordinate Y Coordinate Y of the

fixed refuge position

Explanation
Coordinate Y of the fixed refuge position is
set up within the feeding frame in the unit of
0.1mm.

(Caution) Coordinate X is (+) when the needle position is right of the origin.
It is (-) when the needle position is left of the origin.
Coordinate Y is (+) when the needle position is behind the origin.
It is (-) when the needle position is in front of the origin.

Needle
position

96

(3) Bank function setup

The bank function means a function of sewing effected through changeover to a pattern by an external signal,
which is registered in multiple pattern buttons in cases of cassette discrimination and others.
For sewing by the bank function, an external signal input is entered before the feeding frame is lowered at the
time of pedal treading-on. According to the input condition, a maximum of 16 patterns can be used for changeover.
When the bank function is used, the fixed refuge position preset in regard to 5.-(2) Fixed escape position
setting is automatically enabled.
The reason is that the feeding frame in ordinary operation is made ready at the start of sewing (or the second
origin). This function is always possible if there is only one sewing pattern. In the case of the bank function,
however, the next sewing pattern is not always coinciding with the previous sewing pattern (or the second
origin) at the start of sewing. Therefore, it is necessary to use this refuge position function to secure the same
standby position for the feeding frame.
1. It is not always necessary to set up the memory switch K90 because the fixed refuge position mode is automatically secured for the bank function.
2. The fixed refuge position, defined by the fixed refuge position Coordinate X of Memory Switch K117 and the fixed
refuge position Coordinate Y of Memory Switch K118, is regarded as the standby position of the feeding frame
for the bank function.
In standard setting, the feeding frame stops at the origin because the conditions are set at X:0 and Y:0. An
arbitrary position can be set up with the memory switches K117 and K118.
The bank functions and the input terminals can be set up with the following memory switches:
(1) Bank function setup
The memory switch K130 is used to set up the number of banks (quantity of input terminals).
Setup

Contents

Explanation

Bank disabled

The bank function is not used.

No. of banks 2

Two patterns are set for the number of banks.

One Input Terminal 0 is used.

No. of banks 4

Four patterns are set for the number of banks.

Two Input Terminal 0 to 1 are used.

No. of banks 8

Eight patterns are set for the number of banks.

Three Input Terminal 0 to 2 are used.

No. of banks 16

Sixteen patterns are set for the number of banks.

Four Input Terminal 0 to 3 are used.

CP20: 0

CP20: 1

CP20: 2

CP20: 3

CP20: 4

97

(2) External input terminal setup

The input terminal numbers to be used for the bank function are set up.
1. IP-400

1) Bank function setup screen display

When the number of K130 bank connection select
terminals is preset for the memory switch data (Level
2), the bank function button
(A) is displayed on
the mode changeover screen. When this button is
pressed, the bank function setup screen is displayed.
2) Registration of the direct pattern number
When the direct pattern number registration button
(C) is pressed for a setting input terminal number (B), the direct pattern number selection screen is
displayed. However, the selectable direct pattern numbers are limited only for the individual sewing. The
direct pattern number to be registered for the input
terminal is selected as indicated by (D).

E
B
C

3) Bank function setup

The bank function can be set up through changeover
operation of the bank function setup button
(E).
: Bank function turned ON
: Bank function turned OFF

98

When the bank function setup screen is closed and

the data input screen is displayed, a pictograph (F)
for indicating the ON status is displayed if the bank
function is turned ON.
F

When the
key is pressed, the bank mode
screen is displayed.

When the presser is lowered, the direct pattern sewing screen is displayed and sewing can be carried
out.
For the direct patterns to be displayed on the sewing screen, the pattern numbers are automatically
changed over if there is coincidence of an input with
the relevant input terminal.

99

2. CP-20
The bank input terminals 0 to 3 (input Nos. 3 to 6) are assigned to arbitrary input terminals of the memory
switches Nos. 300 ~ 331.
1) When the
key is continuously pressed for 6 seconds in the state that the
sewing LED is unlit, the service setup mode is assumed for the memory switches
and the bank mode is set up.
In regard to the method of memory switch setup, refer to the section of memory
switch data change of the Instraction Manual.
2) Using the
and
keys, select the bank mode and press the
The sewing Led is then lit up.

key.

3) Make

key.

and

key setting for bank mode ON or OFF. Press the

4) Register the direct pattern number for the input terminal. Input terminal changeover
is possible with the
key. The direct pattern number can be selected with the
and
keys.
5) Press the
key to register the contents of setup. The sewing LED is unlit and
the status of memory number selection is recovered.
The upper 2 The lower 3 digdigits denote its denote the
the input ter- pattern number.
minal number.

6) Press the
key to close the memory switch setup mode. The normal status is
then recovered.
Relationship between bank input terminals and bank numbers
Input terminal

Input terminal
Bank number

Input terminal
Bank number

Bank No. 1

Bank No. 2

Bank No. 3

Bank No. 4

Input terminal
Bank number

Bank No. 5

Bank No. 6

Bank No. 7

Bank No. 8

H: High, L: Low (when bank input active = Low)

100

Bank number
3

Bank No. 9

Bank No. 13

Bank No. 10

Bank No. 14

Bank No. 11

Bank No. 15

Bank No. 12

Bank No. 16

(4) Port I/O setup

This sewing machine is provided with the machine control functions that are enabled only by the machine main body
through the generation of signal outputs to the outside and the reception of signal inputs from the outside, without
the intervention by any appropriative I/O unit and other devices.
By making connections with proper external sequencers (programmable controllers) or using the simplified sequencer functions that are available at the main body, the machine is possible to be modified into a mechanical
system of various annex units.
1. Input terminal setup
Input No.
Contents
0
Nil
For the actuator
1
Void
2
Detection of material end
sensor
3
Bank input 0
4
Bank input 1
5
Bank input 2
6
Bank input 3
For pattern data inputs
33
External input 0
34

External input 1

35

External input 2

36

External input 3

37

External input 4

38

External input 5

39

External input 6

40

External input 7

41

External input 8

42

External input 9

43

External input 10

44

External input 11

45

External input 12

46

External input 13

47

External input 14

48

External input 15

Explanation
No input

Detection of material end is enabled with the first Mark 1 command of the pattern data.
When the input terminal becomes active, the section to the second Mark 1 command is skipped.
Input terminal 0 when the bank function is selected
Input terminal 1 when the bank function is selected
Input terminal 2 when the bank function is selected
Input terminal 3 when the bank function is selected
Sewing is suspended until the input terminal becomes active with the External Input 0 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 1 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 2 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 3 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 4 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 5 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 6 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 7 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 8 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 9 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 10 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 11 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 12 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 13 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 14 command of the pattern data.
Sewing is suspended until the input terminal becomes active with the External Input 15 command of the pattern data.

Operation prohibit / weight request

49
Presser SW input prohibited
50
Start SW input prohibited
51
Sewing start wait
52
53

54

55

Entry of presser switch 1 to 4 inputs is prohibited in active phase.

Entry of start switch inputs is prohibited in active phase.
Start of sewing start switch operation is waited in active phase. Sewing is started in nonactive phase. This signal is disregarded in the middle of sewing.
XY motor start wait
Start of XY motor driving is waited in active phase. The XY motor driving is started in nonactive phase. This signal is disregarded in the middle of XY motor driving.
Sewing machine start wait
Start of sewing machine head rotation is waited in active phase. Intermediate presser lowering and sewing machine head rotation are started in non-active phase. Upper position reset
is not included. This signal is disregarded in the middle of sewing machine head driving.
Sewing machine stop wait
Operation is suspended after the stoppage of sewing machine head rotation and wiper and
intermediate presser lifting operation in active phase. Subsequent operation is started in
non-active phase. Upper position reset is not included. This signal is disregarded in the middle
of sewing machine head driving.
Feeding frame vertical motion Total lifting and lowering of the feeding frame is suspended in active phase. Total lifting and
wait
lowering of the feeding frame is performed in non-active phase. Feeding frame lifting and
lowering are not included at the time of presser pedal operation.

101

2. Output terminal setup

Output No.
Contents
0
Nil
For the actuator
1
Feeding frame 1
2
Feeding frame 2
3
Feeding frame 3
4
Feeding frame 4
5
(Intermediate presser)
6
Void
7
Reverse shaft
8
Third thread tension
9
Needle cooler
For pattern data outputs
33
External output 0
34
External output 1
35
External output 2
36
External output 3
37
External output 4
38
External output 5
39
External output 6
40
External output 7
41
External output 8
42
External output 9
43
External output 10
44
External output 11
45
External output 12
46
External output 13
47
External output 14
48
External output 15
Status of sewing machine head
49
Needle upper position
50
Needle lower position
51
Needle upper dead point position
52
Needle lower dead point position
53
Thread trimming signal
54

During rotation

55

Sewing machine brake signal

56
Void
Status of sewing machine unit
57
Status of setup
58
Status of READY operation
59
READY status
60
Sewing status
61
62

During sewing
Sewing machine in driving

63
64
65
66

Resetting to the sewing start point

Sewing being stopped on the way
Stop with sewing error display
Temporary stop of sewing

67
68
69

XY feeding operation
Origin reset
Presser lowering status

Explanation
No output
Feeding frame right lifting
Feeding frame left lifting
(Feeding frame right 2-stage stroke)
Feeding frame left 2-stage stroke
(Signal output)
Reverse shaft setting side
Third thread tension closed
Needle cooler air output
Reverse signal output with the External Output 0 command of the pattern data
Reverse signal output with the External Output 1 command of the pattern data
Reverse signal output with the External Output 2 command of the pattern data
Reverse signal output with the External Output 3 command of the pattern data
Reverse signal output with the External Output 4 command of the pattern data
Reverse signal output with the External Output 5 command of the pattern data
Reverse signal output with the External Output 6 command of the pattern data
Reverse signal output with the External Output 7 command of the pattern data
Reverse signal output with the External Output 8 command of the pattern data
Reverse signal output with the External Output 9 command of the pattern data
Reverse signal output with the External Output 10 command of the pattern data
Reverse signal output with the External Output 11 command of the pattern data
Reverse signal output with the External Output 12 command of the pattern data
Reverse signal output with the External Output 13 command of the pattern data
Reverse signal output with the External Output 14 command of the pattern data
Reverse signal output with the External Output 15 command of the pattern data
Upper stop position
40 to 62 (Always ON shortly after Power ON)
(Internal signal)
80 to 123 (Always OFF shortly after Power ON)
Reverse rotation needle lifting position 5 to 30
(Always OFF shortly after Power ON)
Lower stop position
209 to 239 (Always OFF shortly after Power ON)
During thread trimming stop (not used) ON beneath the needle shortly before stoppage
OFF at +70ms above the needle
In the middle of sewing machine driving ON at the start of rotation OFF at +120ms above
the needle
During sewing machine stop
ON beneath the needle shortly before stoppage
OFF at +120ms above the needle

In the setup condition

Ready key Origin retrieval Moving to the sewing start point and thereafter
In the ready condition
From the start of sewing to the feeding frame lifting after moving to the sewing start point.
Feed forward included.
From the start of sewing to the end of pattern data. Jump feed included.
In the middle of sewing machine head driving during sewing. Bobbin and needle lifting reset
not included.
From the end of pattern data to the reset of the sewing start point.
Stopped with a midway stop command of the pattern data.
Error display being presented because of error stop during sewing.
Error stop during sewing or temporary stop after the promotion of stitching due to pattern
check, etc.
Jump feed during sewing, pattern check, feed forward/return motion, and others.
Origin reset key Reset to the sewing start point
Presser lowering key Presser lowering status

102

Output No.
70
71
72
73
74
75
76
77
78
79
80
81
For the trigger
97
98
99
100

Contents
Bobbin status
Main unit input status
Pattern check status
Last mode status

Explanation
Bobbin key Bobbin status
Main unit input key Main unit input status
Pattern check, thread tension / intermediate presser height command setup
Last mode status (Sewing machine revolutions / output / XY / presser thread cutter / thread

Presser SW input effective

Start SW input effective
Temporary stop SW turned OFF
Thread breakage error OFF
Air pressure being lowered
Other errors being present
Sewing counter carryover
Sheet counter carryover

clamp / intermediate presser test mode)

When the presser switch input is effective
When the start switch input is effective
Temporary stop switch error (E050) being displayed (E050). OFF by reset.
Thread breakage error (E052) being displayed. OFF by reset.
Air pressure low error (E031) being displayed. OFF by reset.
Errors other than 76 to 78 being displayed. OFF by reset.
Sewing counter carryover being displayed. OFF by counter reset.
Sheet counter carryover being displayed. OFF by counter reset.

READY operation start

READY operation end
Sewing start
Before sewing start point reset

101

After sewing start point reset

102
103
104
105
106
107

Before sewing machine start

After sewing machine stop
Before jump feed start
Before origin reset start
Before total presser lowering
Before total presser lifting

When the READY key is accepted. ON for 100ms.

After moving to (READY key ) sewing start point. ON for 100ms.
When the Start switch is accepted. (Normal / Midway stop / Temporary stop). ON for 100ms.
Before sewing start point reset (after pattern data end). ON for 100ms. Origin reset not
included.
After sewing start point reset (before feeding frame lifting). ON for 100ms. Origin reset included.
Before sewing machine head driving (before feeding frame lowering). ON for 100ms.
After sewing machine head stop (after wiper and before feeding lifting). ON for 100ms.
Jump feed operation / Feed forward / Return operation. ON for 100ms.
When the origin reset key is accepted. ON for 100ms.
At the time of total presser lowering (Ready, threading, bobbin, etc.). ON for 100ms.
At the time of total presser lifting (Ready, threading, bobbin, etc.). ON for 100ms.

103

[Normal Status Diagram of the Port I/O]

G: Second origin
A

C: Midway stop

B
O: Origin

57: Setting condition

READY SW ON

58: Ready operation state

59: Ready state
60: Sewing state
61: Sewing forwarded
62: Sewing machine driving
63: Sewing start point reset
64: Midway stop
65: Sewing error display stop
66: Sewing temporary stop
67: Jump feed
68: Origin reset
69: Presser lowering state
70: Bobbin state
71: Main unit input state
72: Shape check state
73: Check program state
74: Presser SW input effective
75: Start SW input effective

Presser
SW ON

Start SW ON

Presser SW ON

76: Temporary stop SW stopped

77: Thread breakage error stop
78: Air pressure lowering stop
79: Stop on account of another error
80: Sewing counter carryover
81: Sheet counter carryover
97: Ready operation start
98: Ready operation end
99: Sewing start
100: Before sewing start point reset
101: After sewing start point reset
102: Sewing machine start
103: Sewing machine stop
104: XY feed start
105: Origin reset start
106: Total presser lowering
107: Total presser lifting

49: Presser SW input prohibited

50: Start SW input prohibited
51: Sewing start wait
52: XY driving wait
53: Sewing machine start wait
54: Sewing machine stop wait
55: Feeding frame lift/lower wait

104

Start SW ON

[Error Status Diagram of the Port I/O]

57: Setting condition

58: Ready operation state
59: Ready state
60: Sewing state
61: Sewing forwarded
62: Sewing machine driving
63: Sewing start point reset
64: Midway stop

Reset SW ON

Reset SW ON

Reset SW ON

Reset SW ON

65: Sewing error display stop

66: Sewing temporary stop
Feed return SW ON
67: Jump feed
Origin reset SW ON
68: Origin reset
69: Presser lowering state
70: Bobbin state
71: Main unit input state
72: Shape check state
73: Check program state
74: Presser SW input effective
Start SW ON

Start SW ON

Start SW ON

Start SW ON

Start SW ON

75: Start SW input effective

Temporary stop SW ON

Presser SW ON
76: Temporary stop SW stopped
77: Thread breakage error stop

Temporary stop
SW ON

Presser SW ON

Thread breakage error

Air pressure lowering error

78: Air pressure lowering stop

79: Stop on account of another error

Sewing counter clear

Sewing counter carryover

80: Sewing counter carryover

Sheet counter carryover

Sheet counter clear

81: Sheet counter carryover

97: Ready operation start
98: Ready operation end
99: Sewing start
100: Before sewing start point reset
101: After sewing start point reset

Thread breakage SW ON

102: Sewing machine start

103: Sewing machine stop
104: XY feed start
105: Origin reset start
106: Total presser lowering
107: Total presser lifting

49: Presser SW input prohibited

50: Start SW input prohibited
52: Sewing start wait
52: XY driving wait
53: Sewing machine start wait
54: Sewing machine stop wait
55: Feeding frame lift/lower wait

105

[Miscellaneous Status Diagram of the Port I/O]

57: Setting condition

Ready SW ON

Ready SW ON

Test sewing SW Test sewing Ready SW ON

Test sewing SW OFF

58: Ready operation state

59: Ready state
60: Sewing state
61: Sewing forwarded
62: Sewing machine driving
63: Sewing start point reset
64: Midway stop
65: Sewing error display stop
66: Sewing temporary stop

Feed forward SW ON

67: Jump feed

Origin reset SW ON
68: Origin reset

Presser lowering SW ON

Presser lowering SW OFF

9: Presser lowering state

Bobbin SW ON

Bobbin SW OFF

70: Bobbin state

Main unit input SW OFF

Main unit input SW ON

71: Main unit input state

Shape check SW ON

Shape check SW OFF

72: Shape check state

73: Check program state
74: Presser SW input effective
Presser SW ON

Presser SW ON

75: Start SW input effective

76: Temporary stop SW stopped
77: Thread breakage error stop
78: Air pressure lowering stop
79: Stop on account of another error
80: Sewing counter carryover
81: Sheet counter carryover
97: Ready operation start
98: Ready operation end
99: Sewing start
100: Before sewing start point reset
101: After sewing start point reset
Start SW ON
102: Sewing machine start
Start SW ON
103: Sewing machine stop
104: XY feed start
105: Origin reset start
106: Total presser lowering
Presser SW ON
107: Total presser lifting
Presser SW ON
49: Presser SW input prohibited
50: Start SW input prohibited
51: Sewing start wait
52: XY driving wait
53: Sewing machine start wait
54: Sewing machine stop wait
55: Feeding frame lift/lower wait

106

Start SW ON

[Sewing Machine Driving Status Diagram of the Port I/O]

49: Needle upper position

50: Needle lower position
51: Needle upper dead point position
52: Needle lower dead point position
53: Thread trimming signal

50ms

54: During rotation

120ms

55: Sewing machine brake

120ms

102: Sewing machine start

103: Sewing machine stop
20ms
Intermediate presser lowering

Wiper driving

Intermediate presser lifting

[Check Program Status Diagram of the Port I/O]

57: Setting condition

Sewing machine check

program SW ON

Presser thread trimming check program SW ON

Intermediate presser check
Needle thread clamp check program SW ON
program SW
XY check program SW ON

73: Check program state

74: Presser SW input effective
75: Start SW input effective
102: Sewing machine start

Ready SW ON
Reset SW ON

103: Sewing machine stop

Start SW ON

Start SW ON

104: Jump feed start

106: Total presser lowering
107: Total presser lifting

49: Presser SW input prohibited

50: Start SW input prohibited
51: Sewing start wait
52: XY driving wait
53: Sewing machine start wait
54: Sewing machine stop wait
55: Feeding frame lift/lower wait

107

Start SW ON

Output check program SW ON

3. Setup procedures
A

(1) IP-400
1) Display of the port I/O screen
When the
switch is continuously pressed for
about 6 seconds and the page changeover button
is pressed, the port I/O setup button
(A) is
displayed. When this button is pressed, the port I/O
setup screen is displayed.

2) Selection of the port I/O screen

For port I/O setup, four I/O setup screens are available. A required function number can be set on a
relevant screen.
B : Output number setting
C : Input number setting
D : Virtual I/O number setting
E : Switch operation prohibition setting
Setup screen changeover is possible with the right
and left scroll buttons
(F) located on the

B
F
G

top of each screen.

108

F
G
L

H
K

3) Port I/O setup

To make output number setting, input number setting, and virtual I/O number setting, the setup button
(G) is pressed to enter an input of the setting
function number (H) in the selected terminal through
the ten key (I). The signal type is selected from High
(J) and Low (K). In the case of virtual I/O number
setting, it is selected from output
and input
.
To make switch operation setting, the setup button
(L) is pressed to select the signal type from High
(M) and Low (N).

(2) CP-20
It is possible to make setting with the memory switches (Level 2) No. 300 to 401.
In regard to the method of input entry, refer to 4. Memory Switches, (2) Function list , Level 2 (Simplified panel).

109

4. Input for sequence

CN82
CN79
I 01 1

GND

3.3K

+5V

CN80
+5V

I 09 1

I 06 2
GND 3

3.3K

I 02 3

GND

I 03 5

GND

I 04 7

110

GND

I 05 9

CN81

+5V
GND

I 10 3

4
+5V
I 07 5
GND 6
+5V

7
I 08 8
GND 9

GND 10

CN80, CN81, and CN82 are not integrated at shipment.

To use those connectors, mount those first.
CN80: HK01650009B (ELCO: 00 8263 0912 00 002)
CN81: HK01650008B (ELCO: 00 8263 0812 00 002)
CN82: HK01650012B (ELCO: 00 8263 1212 00 002)
Cord side
Pin: HK016540000 (ELCO: 60 8263 0513 00 808)
8P housing: HK01651008B (ELCO: 60 8263 3088 15 002)
9P housing: HK01651009B (ELCO: 60 8263 3098 15 002)
12P housing: HK01651012B (ELCO: 60 8263 3128 15 002)
Use CN79 and CN81 for switch input.
Use CN80 and CN82 for sensor or switch input.

GND

I 11 5
GND 6
I 12 7

GND

3.3K

+5V

+5V

+5V

1
2
I 13
GND 3

+5V

I 14 5
GND 6

+5V

I 15 8
GND 9

+5V

10

I 16 11
GND 12

3.3K

5. Output for sequence

+24V

Ic=0.8A

CN84

+24V

111

1
2

+24V

3
4

+24V

5
6

+24V

7
8

+24V

9
10

+24V

O 01

Ic=0.8A

O 02

O 03

O 04

O 05

CN83

+24V

1
2

+24V

3
4

+24V

5
6

+24V

O 06

CN78
1
2

+24V

3
4

+24V

5
6

+24V

7
8

+24V

+24V

Ic=0.8A

O 07

O 08

7
8

+24V

O 09

10

10
11

+24V
O 10

CN83 and CN78 are not integrated at shipment.

To use those connectors, mount those first.
CN83: HK01650011A (ELCO: 00 8263 1112 00 001)
CN78: HK01650012A (ELCO: 00 8263 1212 00 001)
Cord side
Pin: HK016540000 (ELCO: 60 8263 0513 00 808)
11P housing: HK01651011A (ELCO: 60 8263 3118 15 001)
12P housing: HK01651012A (ELCO: 60 8263 3128 15 001)
It is recommended to use the drive transistor with 0.5 A or less even though the rated current is 0.8 A.
Make sure that the total current is equal or less than 1 A.

O 11

O 12

O 13

O 14

O 15

11 +24V
12 O 16

(5) Simplified program setup

This machine is provided with the simplified program functions, which can make the programming of various additional devices (stacker, unit, etc.) according to sewing machine operation. In conjunction with the port I/O output
functions, modification into such additional devices can be carried out in the main unit of the sewing machine.
1. Specifications
(1) Operation by a maximum of five programs is possible.
(2) Inputs of a maximum of 99 steps can be entered per program.
(3) Interactive operation is possible among the five programs.
2. Setting items
The simplified program specifies the following five items per step.
No.

Setting item

Contents

Command

Output information Contents of multiple outputs are set up for High and Low of the respective 16 output
terminals and 16 virtual I/O ports.

Input information

Parameter

1
Parameter 2

The method of step execution is displayed.

Multiple input conditions are set up for High and Low of the respective 16 output terminals, 16 input terminals, 16 virtual I/O ports, and 6 operation switches.
Skip destination step No. or program No. is set up.
The input conditions of delay time, No. of stitches, No. of repetition times, etc. are set
up.

The virtual I/O port is provided for an interface to be used for sewing machine control and simplified program control.
In the case of port I/O setup, either an input or output is set up as seen from the sewing machine control side.
(Caution) The virtual I/O port is an internal signal of the sewing machine. It cannot be brought out directly
to the outside.

3. Control operation
At the start of simplified program execution, operation is sequentially carried out starting from Step No. = 1, at the
intervals of 1ms for each step.
At the beginning of step execution, the conOutput terminal
Sewing machine control
Simplified program
tents of output information setup are gencontrol
o01
erated. Operation is suspended (with the
o02
execution step No.) until the setup condiActuator driving
Output information
tions for the input information or Param- External pattern output
o15
Status output
eter
have been established. When these
o16
conditions are established, operation is forwarded to the next step No. or the skip
Virtual I/O port
destination step No. defined by Parameter
v01
. Such a sequential operation is repeated
v02
till the completion command.

v15
v16

Actuator sensor
External pattern input
Operation wait input

Input terminal
i01
i02

i15
i16
Presser SW, etc.
psw1

(Caution)
In the simplified program control, the I/
O terminals and others are directly controlled based on the output and input
information, irrespective of the result of
port I/O setup.
In particular, the output data are immediately generated at the beginning of
step execution for the output terminals
and virtual I/O ports. In regard to I/O
mismatching and synchronization for
sewing machine control, therefore, programs have to be established carefully
on the side of simplified program.

Switch input

112

psw4
ssw
esw

Input information

4. Operational Procedures
(1) Simplified program selection screen display
When the
key is continuously pressed for 3
seconds, the simplified program button
(A) is
displayed on the mode changeover screen. When
this button is pressed, the simplified program selection screen is displayed.

(2) Simplified program effective / ineffective

The simplified program comes in five patterns. In the
initial state, all the patterns are set at OFF. When the
simplified program setup button (B) is used, each
program can be made effective or ineffective.
: Simplified program effective
: Simplified program ineffective

(3) Simplified program editing

Simplified program No.
and the registered number of steps
are displayed on the program
editing button
(C). When this button is pressed,
the simplified program editing screen is displayed,
which corresponds to the simplified program editing
button.

113

In the simplified program editing screen, the editing step

is selected with the use of the step forwarding button
(D) and the step return button
(E). For each
selected step, it is possible to carry out command port I/
O setting and parameter setting.
A maximum of 99 steps can be entered.

1) Command selection
When the command selection button
(F) is
pressed on the simplified program editing screen,
the command selection screen is displayed.
The command that is being selected is displayed on
the button.

On the command selection screen, the command

button (G) is displayed. Press the selecting command
button and then press the Enter button
(H).
In regard to command descriptions, refer to (4) list of
simplified program commands.

I
J
K
L

2) Port I/O information setup

The port status can be set up for the four items as
specified below.
(I) Output information (High) setup button
(J) Output information (Low) setup button
(K) Input information (High) setup button
(L) Input information (Low) setup button
When the setting button is pressed, the I/O data selection screen is displayed.

114

On the port setup screen, current setting items are displayed at the top left of the screen.
: Output information (High) setup screen
: Output information (Low) setup screen
: Input information (High) setup screen
O

: Input information (Low) setup screen

Using the page turning buttons

(M, L), the
displayed port type can be changed.
The port comes in the four types as specified below.
: Output port No.
: Input port No.
: Virtual I/O port No.
etc.: Presser SW 1 to 4, Start SW, Temporary stop
SW
The port No. button is displayed on the screen. Press
the button that corresponds to current setting.
The selection status button is displayed in gray.
After selection, press the Enter button
(O).

For output setting, press the output button

(P) to
obtain the item for which the displayed step has been
set up. Therefore, this item can be examined.

115

3) Parameter input
Corresponding to the selected command, the parameter input button is displayed.
When the parameter input button (Q) is pressed, the
parameter input screen is displayed.
Enter a numerical input through the ten key (R) and
press the Enter button
(S).
In regard to the parameters that correspond to the
commands, refer to (4) list of simplified program commands.

4) Step insertion
It is possible to insert a step before the displayed
step.
When the step insertion button
(T) is pressed,
the command selection screen is displayed.
Select the command that is required to be inserted,
and press the Enter button
(U). Then, the
required step is inserted.

116

5) Step deletion
It is possible to delete the step that has been displayed.
When the step deletion button
(V) is pressed,
the deletion check screen is displayed. When the
Enter button
(W) is pressed, the displayed step
is deleted and the step standing behind is shifted
forward.

6) Checking the status of the simplified program in

the sewing screen
The simplified program button
(A) is displayed
in the sewing screen if this simplified program is available. The simplified program select screen is presented and the effective simplified program button
(B) is displayed.
Select the simplified program number the status of
which is being checked, and press the ENTER button
(C).
The simplified program confirmation screen is presented and the present step number and the status
of I/O are displayed.
The port number without I/O confirmation is displayed
in gray (D).
B

117

5. To use the simplified program with CP-20

(1) Simplified program ON/OFF
1) When the power supply is turned on with the
mode.

2) When the

key is pressed, the simplified program number and the ON/OFF status are displayed.

P1

Using the

key kept pressed, the unit is started in simplified program

key, it is possible to select the simplified program number.

Using the

key, ON/OFF changeover is possible.

Upon the completion of modification, turn off the power supply.

(2) Write/read of the simplified program data with the smart media
1) When the power supply is turned on with the
mode.

2) When the
media.

P2

key kept pressed, the unit is started in simplified program

key is pressed, write/read of the simplified program data becomes possible with the smart

118

3) Select data Write or Read with the

: Reading

key.
: Writing

4) Using the
,
key, it is possible to select the file number.
1. For data reading
It is possible to select only the file number registered in the smart media.

2. For data writing

It is possible to select only the file number that is not registered in the smart media.

5) When the
key is pressed, reading or writing is started. During data reading or writing, the File No. is
indicated in blinking mode. When the Power OFF is indicated, data writing is finished. Ordinary operation is
recovered when the power supply is turned on again.

119

(4) List of Simplified Program Commands

No.

Function code

Command

Output information Input information

Parameter

Complete

Effective

Ineffective

Ineffective

Ineffective

Program execution is finished.

Delay

Effective

Ineffective

Ineffective

Delay time

0 to 9999ms

Moving to the next step after the lapse of a delay time.

Setting range

Parameter

Setting range

Remarks

120

End

DELy

And

Branch with AND condition

Effective

Effective

Skip destination 1 to 99 steps

No.

Delay time

0: Input waiting till the Moving to the next step when all conditions specified
condition established by input setting are satisfactory (AND input).
1 to 9999ms
Jumping to the step preset by skip destination No.
after the lapse of a delay time as a result of failure
in establishing the input conditions.

or

Branch with OR condition

Effective

Effective

Skip destination 1 to 99 steps

No.

Delay time

0: Input waiting till the Moving to the next step when either condition specified
condition established by input setting is satisfactory (OR input).
1 to 9999ms
umping to the step preset by skip destination No.
after the lapse of a delay time as a result of failure
in establishing the input conditions.

STiA

Branch with AND condition Effective

for No. of stitches

Effective

Skip destination 1 to 99 steps

No.

Number of
stitches

0 to 9999 stitches

Moving to the next step after the lapse of the preset number of stitches. Jumping to the step specified
by the skip destination No. within the range of the
preset number of stitches when all conditions specified
by input setting are satisfactory (AND input).

STio

Branch with OR condition

for No. of stitches

Effective

Skip destination 1 to 99 steps

No.

Number of
stitches

0 to 9999 stitches

Moving to the next step after the lapse of the preset

number of stitches. Jumping to the step specified
by the skip destination No. within the range of the
preset number of stitches when either condition
specified by input setting is satisfactory (OR input).

JUMP

Jump repetition counter Effective

Ineffective

Skip destination 1 to 99 steps

No.

Repetition
counting
value

0: Infinite
1 to 9999 times

Repeated in the range of skip destination steps specified

by Jump till repetition counter carryover.
Infinite loop is performed when setting is made at 0.
Moving to the next step after repetition counter carryover.
(Caution) Do not perform nest input of this command.

rEST

Program reset

Ineffective

Program No.

Ineffective

In the case of the step initialization of the specified

program number, the specified program steps are
forcedly returned to the initial steps.

Input information setup range

Effective

Effective

Contents

o01H to o16H

High output of external output terminals 01 to 16

v01H to v16H

High output of virtual I/O ports 01 to 16

o01L to o16L

Low output of external output terminals 01 to 16

v01L to v16L

Low output of virtual I/O ports 01 to 16

1 to 5 programs

Input information setup range

o01H to o16H
i01H to i16H
v01H to v16H
p1H to p4H,sH,eH
o01L to o16L

Contents
High status input of external output terminals 01 to 16
High status input of external input terminals 01 to 16
High status input of virtual I/O ports 01 to 16
High status input of presser SW1 to 4 (p), Start SW (s), Temporary stop SW (e)
Low status input of external output terminals 01 to 16

i01L to i16L

Low status input of external input terminals 01 to 16

v01L to v16L

Low status input of virtual I/O ports 01 to 16

p1L to p4L,sL,eL

Low status input of presser SW1 to 4 (p), Start SW (s), Temporary stop SW (e)

(5) Program sample

1) Simplified stacker program 1

After sewing start

point reset
Stacker material open

his is an example of program establishment intended to make material stacking, to be

done simultaneously with feeding frame lifting after the completion of sewing.

Stacker material clamp

Stacker material payout

200ms

400ms

300ms

[Port I/O Setup]

Terminal
output

Contents

Remarks

121

o01
o02
o03

1: Feeding frame right

2: Feeding frame left
4: Feeding frame

o04
o05
o06
o07

2-step stroke
7: Inverting shaft
9: Needle cooler
(Stacker material open)
(Stacker material clamp)

o08

(Stacker material payout) Simplified program output

Standard
Standard
Standard
Standard
Standard
Simplified program output
Simplified program output

Terminal
output

Contents

Remarks

Virtual I/O
v01
v02
v03
v04
v05
v06
v07

i01
i02
i03
i04
i05
i06
i07

I/O

Contents

Remarks

Output 101: After sewing start point reset

v08

i08

(Caution) For the descriptions in the parentheses ( ) of o06 ~ o08 above, the terminals directly generate outputs with the aid of the simplified program. Port I/O setting is
disabled.
[Simplified Program Setup]
End,DELy,
And,or,
STiA,Stio,
JUMP,Rest

Step

No.

Command

o01H to o16H
v01H to v16H

o01L to o16L
v01L to v16L

o01H to o16H
o01L to o16L
Delay time: Unit of 1ms
d. Delay time
i01H to i16H
i01L to i16L
Pn. Program No. c. Number of stitches Number of stitches: Unit of 1 stitch
v01H to v16H
v01L to v16L
Sn, Step No
r. Repetition counter
p1H to p4H,sH,eH p1L to p4L,sL,eL

Output information High Output information Low Input information High Input information Low

And

DELy

DELy

DELy

o06H,o08H

JUMP

o07H

End

Parameter

v01L

Parameter

Remarks

d.0

Waiting till sewing start point reset

o06L,o07L

d.200

Stacker material open / material clamp ON. 200ms delay.

o08L

d.400

Stacker material payout ON. 400ms delay.

d.300

Stacker material open / material payout OFF. 300ms delay.

r.0

Stacker material clamp OFF. To Step 1.

Sn.1

2) Stacker program 2
This is an example of program establishment intended to make material stacking, to be done after the material cloth has been clamped before feeding frame lifting
at the time of the completion of sewing.

Sewing forwarded
Sewing machine started
Before sewing start point reset
After sewing start point reset
Before origin reset
Feeding frame lift/lower wait

100ms

Stacker movement

500ms

Stacker material clamp

122

Stacker material stacking

300ms
Stacker movement sensor
Stacker material clamp sensor
Normal operation

When sewing interrupted

[Port I/O Setup]

Terminal output

Contents

Remarks

Terminal input

Contents

Remarks

Virtual I/O

I/O

Contents

o01

1: Feeding frame right

Standard

i01

v01

Output 61: Sewing forwarded

o02

2: Feeding frame left

Standard

i02

v02

Output 102: Sewing machine started

o03

4: Feeding frame 2-stage stroke Standard

i03

v03

Output 100: Before sewing start point reset

o04

7: Reverse shaft

Standard

i04

v04

Output 101: After sewing start point reset

o05

9: Needle cooler

Standard

i05

v05

Output 105: Before origin reset

o06

(Stacker move)

Simplified program output

i06

(Stacker movement sensor) Simplified program input

(Stacker material clamp sensor) Simplified program input

o07

(Stacker material clamp)

Simplified program output

i07

o08

(Stacker material stack)

Simplified program output

i08

v06

Input

Remarks

55: Feeding frame lift/lower wait

v07
v08

(Caution) For the descriptions in the parentheses ( ) of o06 ~ o08 and i06 ~ i07 above, the terminals directly generate outputs with the aid of the simplified program. Port I/O
setting is disabled.

[Simplified Program Setup]

Step

End,DELy,
And,or,
STiA,Stio,
JUMP,Rest

No.

Command

And

or

o01H to o16H
v01H to v16H

o01L to o16L
v01L to v16L

o01H to o16H
o01L to o16L
Delay time: Unit of 1ms
d. Delay time
i01H to i16H
i01L to i16L
Pn. Program No. c. Number of stitches Number of stitches: Unit of 1 stitch
v01H to v16H
v01L to v16L
Sn, Step No
r. Repetition counter
p1H to p4H,sH,eH p1L to p4L,sL,eL

Output information High Output information Low Input information High Input information Low

o06L,

Parameter

Parameter

Remarks

v01L , v02L

d.0

Waiting till sewing machine start.

v03L, v05L

d.0

Stacker movement ON. Waiting till sewing start point

reset or origin reset.

And

And

v03L
v06L

Sn.11

v04L

d.1

To Step 11 if there is no sewing start point reset.

d.0

Feeding frame lifting wait ON. Waiting till sewing start

point reset.

And

And

o07L

i06

d.0

Waiting till stacker movement sensor ON.

i07

d.0

Stacker material clamp ON. Waiting till stacker material clamp sensor ON.

123

DELy

v06H

d.100

Feeding frame lifting wait ON. 100ms delay.

DELy

o06H

d.500

Stacker movement OFF. 500ms delay.

DELy

d.300

Stacker material stacking ON. 300ms delay.

10

JUMP

o07H, o08H

Sn.1

r.0

Stacker material clamp / material stacking OFF.

11

JUMP

o06H

Sn.1

r.0

Stacker movement OFF. To Step 1.

12

End

o08L

(6) Port I/O setup sheet

Terminal
output

Contents

Remarks

Terminal

Contents

Remarks

Virtual I/O

input

124

o01

i01

v01

o02

i02

v02

o03

i03

v03

o04

i04

v04

o05

i05

v05

o06

i06

v06

o07

i07

v07

o08

i08

v08

o09

i09

v09

o10

i10

v10

o11

i11

v11

o12

i12

v12

o13

i13

v13

o14

i14

v14

o15

i15

v15

o16

i16

v16

I/O

Contents

Remarks

(7) Simplified program setup sheet

Step

No.
1
2
3
4
5
6
7
8
9

125

0
1
2
3
4
5
6
7
8
9
0

End,DELy,
And,or,
STiA,Stio,
JUMP,Rest

o01H to o16H
v01H to v16H

o01L to o16L
v01L to v16L

o01H to o16H
o01L to o16L
Delay time: Unit of 1ms
d. Delay time
i01H to i16H
i01L to i16L
Pn. Program No. c. Number of stitches Number of stitches: Unit of 1 stitch
v01H to v16H
v01L to v16L
Sn, Step No
r. Repetition counter
p1H to p4H,sH,eH p1L to p4L,sL,eL

Co. Command Output information High Output information Low Input information High Input information Low

Parameter

Parameter

Remarks

(6) Version display

1. To display the version information screen:
Hold down the
key for 3 seconds to call up the
version information button,
(A) on the screen.
Press this button to display the version information
screen.

The version information screen shows the version

information of your sewing machine.
E

B: Panel program version

C: Main program version
D: Main shaft program version

Pressing the cancel button,

(E) closes the version information screen and calls up the mode screen.

C
D

2. To display the detail screen:

Press the detail screen button,
panel program detail screen.

(F) to call up the

G: Module
H: RVL
I: Checksum
Pressing the cancel button,
(J) closes the detail
screen and calls up the version information screen.
Pressing the
key closes the detail screen and
calls up the data input screen which you have selected.

* The check program allows you to see version information on the simplified panel.

126

(7) Keylock setup

1. To call up the keylock screen:
Hold down the
key for 3 seconds to call up the
keylock button,
(A) on the screen. Press this
button to display the keylock setting screen.
The current status appears on the keylock button.
A

: Keylock is inactivated.

: Keylock is activated.

2. To select keylock and activate it:

Select the keylock activation button,
(B) on the
keylock setting screen and press
. Then, the
keylock setting screen closes and keylock becomes
activated.

3. After closing the mode screen and calling up the

data input screen:
After closing the mode screen and calling up the data
input screen, PICT C indicating that keylock is activated appears on the right of the pattern number.
Only available buttons appear when keylock is activated.

* Memory switch No. 17 allows you to activate keylock

on the simplified panel.

127

(8) Communication screens of the maintenance personnel level (Program rewrite)

The data types allowed to be handled in the communication screens can differ according to the ordinarily used
levels and the specific levels that are used by the maintenance personnel.
1. Types of data that can be handled
In addition to the four ordinary data types, the five more data types can be used for the maintenance personnel
level. Each data type is as specified below.

Data name

Pict

Extension

Contents of data

Adjustment data

Model name +00XXX.MSW

Example) AMS00001.MSW

Data of the memory switches 1 and 2

All sewing machine data

Model name +00XXX.MSP

Example) AMS00001.MSP

All data maintained by the sewing machine

Panel program data

IP + RVL (6 digits).HED Program data and display data of the panel

IP + RVL (6 digits).PXX
IM + RVL (6 digits).IXX

Main program data

MA + RVL (6 digits).PRG

Main program data

Servo program data

MT + RVL (6 digits).PRG

Servo program data

XXX: File No.

128

2. Reading/Writing of adjustment data and all sewing machine data (For the IP-400)

B
C

(1) Display of the communication screen of the maintenance personnel level

When the
key (A) is continuously pressed for 3
seconds, the top left image is turned into the orange
color (B) and a communication screen of the maintenance personnel level is displayed.
(C) is pressed in a communication screen of
the maintenance personnel level, the data selection
screen is displayed.
In this state, it becomes possible to select the adjusting data and all sewing machine data.
3. Program rewriting (For the IP-400)
(1) Selection of the data type
When the data classification button
(C) is
pressed in a communication screen of the maintenance personnel level, the data selection screen is
displayed.
In this state, select the panel program data
(D).

(2) Selection of a file

When the file selection button
(E) is pressed in
a communication screen, the file selection screen is
displayed.
Press the file retrieval button
(F) to select the
download program (G), and press the
button.

129

(3) Program rewrite start

When the start of communication button
pressed, program rewriting is started.

(H) is

(Caution) Never turn off the power or open/shut the

smart media cover during the work. Otherwise, the main body can be destroyed.

Data deleting screen

Data writing screen

Ending screen

When the ending screen is displayed, the replacement

work for the application software has been completed.

If any data writing error screen should be displayed, immediately turn off the power supply and check the [checking items] specified below. Then, take the setup actions
again.
Data writing error screen
[Checking items]
1) Did you open the smart media cover in the middle of
data communication from the smart media card.
2) Data of the smart media card are incorrect, or there
is no data file.
3) The contact point of the smart media card is contaminated, or suffering from poor contact.

130

4. Reading/Writing of the adjustment data and all sewing machine data in the smart media (For the CP-20)
(1) When the power is turned on with the
key kept pressed, the adjustment data mode is started. When the
adjustment data mode is started, the pattern number LED is lit up.
When the power is turned on with the
key kept pressed, the all sewing machine data mode is started. When
the all sewing machine data mode is started, the X scale LED is lit up.
: Adjustment data mode

(2) Select data reading or writing with the

key

: Reading

: Writing

(3) Select the fine number with the

1)

: All sewing machine data mode

and

keys.

For reading
Selection is made possible only for the file number that is registered in the smart media.
to

2)

For writing
Selection is made possible only for the file number that is not registered in the smart media.

to

(4) When the

key is pressed, reading or writing of each data block is started. In the middle of data reading or
writing, the file number is displayed in the blinking mode. When Power OFF is displayed, reading or writing has
been completed.
(5) When the power supply is turned on again, normal operation is recovered.

131

5. Program rewriting (For the CP-20)

(1) When the power is turned on with the
key kept pressed, the rewriting mode of the simplified panel program
is started. When the rewriting mode of the simplified panel program is started, the Y scale LED is lit up.
When the power is turned on with the
key kept pressed, the rewriting mode of the main program is started.
When the rewriting mode of the main program is started, the max. number of rotation LED is lit up.
When the power is turned on with the
key kept pressed, the rewriting mode of the servo program is started.
When the rewriting mode of the servo program is started, the tension LED is lit up.
: Panel program

(2) Using the

display, the

: Main program

: Servo program

key, select the program file for the panel, which is kept in the smart media. In regard to the file
key can be used for changeover between the RVL display and the model code display.
: RVL display

: Model code display

For RVL display, five digits of R (1 digit), V (2 digits), and L (2 digits) are displayed.
The non-display portion (RVL + ) can be displayed with the use of the
and

keys.

Example) RVL 01-03-02

For model code display, the five continued characters from the head are displayed.
The model code of the non-display portion can be displayed with the use of the

and

keys.

Example) AMS-210E
(3) When the
key is pressed, writing of the simplified panel program is started. When Power OFF is displayed,
writing has been completed.

When the power supply is turned on again, normal operation is recovered.

132

6. Use of smart media other than those packed together

When the contents of the smart media card packed together are going to be copied on another smart media card,
the smart media card of the copying destination should be formatted with IP400. Since then, the following directory
configuration should be established with a personal computer.
Information about the method of smart media card formatting is obtainable from the Instruction Manual, [2-25. How
to Use the Communication Functions].

Route directory

[PROG]

[AMS210E]

MTxxxxxx.prg (Servo program)

MAxxxxxx.prg (Main program)
[IPxxxxxx] (IP-400 program)
IPxxxxxx.hed
IPxxxxxx.p01
IMxxxxxx.i01
IMxxxxxx.i10
IMxxxxxx.i11
IMxxxxxx.i12
IMxxxxxx.i13
IMxxxxxx.i21

[
] = Folder
xxxxxx = RVL code (6 digits)

IMxxxxxx.i22
IMxxxxxx.i23
NPxxxxxx.prg (CP-20 program)

133

(9) Information screen at the maintenance personnel level

1. Error history
(1) To display the information screen at the maintenance personnel level:
Hold down the information key,
(A) for approx. 3
seconds in the switch sheet section on the data input screen to call up the information screen at the
maintenance personnel level. On the information
screen at the maintenance personnel level, the color
of PICT at the upper left changes from blue to orange, and there are 5 buttons.

D
C

(2) To call up the error history screen:

Press the error history button,
(B) on the information screen to call up the error history screen.
The error history screen shows the error history of
your sewing machine.

C: Chronological recording number

D: Error code
E: Cumulative energizing time during error (hour)

Pressing the cancel button,

(G) closes the error
history screen and calls up the information screen.

(3) To display details:

For detailed information about errors, press the error button,
(F) that you would like to
see to call up the error detail screen.
PICT (H) in response to error codes appears on the
error detail screen.
Refer to the 11. ERROR CODE LIST.

134

2. Cumulative operating information

B
D

(1) To call up the information screen at the maintenance personnel level:

Hold down the information key
, i for approx. 3
seconds in the switch sheet section on the data input screen to call up the information screen at the
maintenance personnel level. On the information
screen at the maintenance personnel level, the color
of PICT at the upper left changes from blue to orange, and there are 5 buttons.

(2) To display cumulative operating information:

Press the cumulative operating information button,
(A) on the information screen to call up the cumulative operating information screen.

The following 4 items are indicated on the cumulative operating information screen.

B: Cumulative operating time (hour)

C: Cumulative thread trimming count
D: Cumulative energizing time (hour)
E: Cumulative stitch count (x1000 stitches)
Pressing the cancel button,
(F) closes the cumulative operating information screen and calls up the
information screen.

135

(10) Test sewing function

Connecting your PC to the sewing machine allows you to perform test sewing based on data created with PM-1
(sewing data creating and editing software).

Data transmission

IP400

PM-1

Connect your PC and transmit data to the sewing machine after creating it with PM-1, and IP-400 automatically
shows the test sewing screen when the data input screen is called up. Refer to the help screen or the like for how
to operate PM-1.

1. To perform test sewing:

(1) Reception of data for test sewing from PM-1
When data (vector type) for test sewing is transmitted from PM-1, the screen shown at right appears,
and a needle positioning drawing of transmitted data
appears in the center of the screen.
The color of the needle positioning drawing changes
depending on thread tension. If the stitch count of
transmitted data is too large, a needle positioning
drawing does not appear.
A

(2) Edit of vector parameter

The following 3 items are configurable on data transmitted from PM-1.
B

A: Thread tension
B: X-axial enlargement/reduction ratio or actual value
C: Y-axial enlargement/reduction ratio or actual value
* The memory switch, U64, provides selection between
an enlargement/reduction ratio and an actual value.

136

(3) Modification to data

Press the button, A, B, or C to be changed to call up
the numeric keypad. Enter a new value and press
the enter button
(D).

A
D

(4) Test sewing

Press the ready-to-go switch
(E) to call up the
test sewing screen. Test sewing is ready.

(5) Data registration to user pattern

To register test sewing data to the sewing machine,
press the registration button
(F) shown on the
test sewing screen to call up the registration screen.
Enter the user pattern number to which the test sewing data is registered with the numeric keypad (G).

(6) Confirmation of data registration

Press the enter button
(H) to close the registration screen, and registration is completed.

(7) data entry screen

After data registration, the data entry screen automatically appears.

137

2. Color chart indicating thread tension values

An indicated needle positioning drawing varies with thread tensions adjusted for needle entry positions. The following chart shows the colors of lines for thread tensions.

Thread tension

Color

0 to 20

: Gray

21 to 40

: Purple

41 to 60

: Blue

61 to 80

: Light blue

81 to 100

: Green

101 to 120

: Yellowish green

121 to 140

: Orange

141 to 160

: Red

161 to 180

: Pink

181 to 200

: Black

138

6. Test mode
(1) Start (CP-20)
When the check program is started, maintenance and inspection can be carried out.
1) Check program start
1. When the
key is continuously pressed for 3 seconds in the state that the
sewing LED is unlit, a buzzer sound is heard and the user setup mode is assumed
for the memory switch. In this state, check program start can be selected.
(Caution) The check program cannot be selected unless this key is continuously pressed for 3 seconds.
2. Change the memory switch number with the
check program.

and

keys to select the

3. Press the
key to move to the check program. Start the display output test.
Refer to the next page in regard to the contents of the display output test.
4. Press the
key to complete the display output test. Move to the selection of
another test function.
5. Select the check program number with the

Check program number

and

keys.

Check program

Contents

Input signal check

The status of the switch and sensor inputs is displayed

at LED.

XY motor / origin sensor

check

The status of inching operation of the X/Y motor,

operation of origin retrieval, and the X/Y origin sensors
is displayed.

Continuous operation

After the conditions of continuous operation have been

et up, the operational mode moves to the continuous
operation mode.

Main motor rpm check

The sewing machine is started at the preset rpm level

nd the measured rpm number is displayed.

139

Check program number

Check program

Contents

Output check

The wiper and air outputs are generated.

Presser, thread cutter motor/

origin sensor check

The status of inching operation of the presser and

thread trimmer motor, operation of origin retrieval, and
he presser origin / presser sensors is displayed.

Needle thread clamp motor/ The status of inching operation of the needle thread
origin sensor check
clamp motor, operation of origin retrieval, and the needle
thread clamp origin and needle thread clamp sensors is
displayed.

6. Press the

Intermediate presser
adjustment

The status of inching operation of the intermediate

presser motor, operation of origin retrieval, and the
intermediate presser origin sensors is displayed.

Software version display

The software versions of the MAIN and SDC boards

are displayed.

key to define the check program number.

7. When the
key is pressed for each check program, the current check program is completed and the status
of 5. is recovered.
Once the continuous operation mode is started, it cannot be canceled. To complete it, however, it is necessary to
turn the power supply OFF.

140

(2) Display output test (CP-20)

After the movement to a check program, the display output test is started.
The following LEDs are lit at the intervals of one second.

141

(3) Method of confirmation according to each test program No. (CP-20)

1) CP-1 (Input signal check)
It is possible to check the input status of the operation panel keys, pedal switches, and various sensors.
Display of input No.
The input number is updated by +1 each time the
and
keys are pressed simultaneously.
Display of the input status with the item selection LED
ON/OFF
Refer to the table below in regard to the contents of display.

P1

P2

P3

P4

P5

Contents of Display for each Input No.

Pattern
LED

X enlarge Y enlarge
LED
LED

Speed
LED

Counter
LED

Bobbin
LED

Threading Thread tension

LED
LED

Key

Key

Key

Key

Key

Key

Key

Key

Key

Presser
1SW

Presser
2SW

PDET
Sensor

SDET
Sensor

Ready
LED

Thread clamp
LED

1
Key

P5

2
Key

Key

DIPSW2 DIPSW2
-1
-2

AUDET
Sensor

Y motor Presser motor Thread clamp Intermediate

origin
origin
motor presser motor
sensor
sensor origin sensor origin sensor

External
input 5

External
input 6

External
input 15

External
input 16

ADDET
Sensor

DIPSW2 DIPSW2 Start SW

-3
-4
DDET
Sensor

External
input 7

UDET
Sensor

External
input 8

Temporary
stop
SW
Head fall Air pressure X motor origin
SW
SW
Sensor
Presser
3SW

Presser
4SW

Presser Thread External External

motor clamp motor input 1
input 2
sensor
sensor

External
input 3

External
input 4

External
input 13

External
input 14

TG
Sensor

External
input 9

External
input 10

DIPSW2 is a dip switch located on the MAIN board.

142

External External
input 11 input 12

2) CP-2 (XY motor / origin sensor check)

The status of inching operation of the X/Y motor, operation of origin retrieval, and the X/Y origin sensors is
displayed.
1. In the first place, press the
key to carry out needle thread clamping and origin retrieval for the presser and
thread trimmer motor. The presser assumes the lowering condition.
After the completion of preparation, the sewing LED is lit.
2. Operation

According to the status of the selected X/Y origin sensor, 0 or 1 is displayed. The
key is pressed to
make changeover.
Using the
and
keys, drive the selected X/Y
motor in the direction of +/ by 0.1mm each time.
(Caution) Since the circular interpolation system is
used, any motor not selected is also driven.

P1

P2

P3

P4

P5

The selection status of the X motor (X origin sensor) or

the Y motor (Y origin sensor) is displayed. The
key
is pressed to make changeover.
X enlargement/reduction scale rate LED lit: X motor (X
origin sensor)
Using the
key, the selection status of the X motor
(X origin sensor) or the Y motor (Y origin sensor) is
changed over.

Using the Start SW, origin retrieval of the X/Y motors is effected for both shafts.

3) CP-3 (Continuous operation)

After the conditions of continuous operation have been set, the operational mode moves to the continuous operation mode.
To cancel the continuous operation mode, it is necessary to turn the
power supply OFF.
1. Rest time setting
Press the

and

keys to set up the rest time.

Setting is possible within the range of 0 to 9900ms in the unit of 100ms.

(Initial value 2000ms)
After the completion of setting, press the
key.
2. Setting for the presence of origin retrieval at the end of sewing
Press the
and
keys to set up the presence of origin retrieval
at the end of sewing.
A0: Ineffective (Initial value)
A1: Every 100 sewing cycles
A2: Every sewing cycle

143

3. Presser lifting, Lowering frequency vertical times setup

Press the
and
keys to set up the presser vertical times.
B0: Ineffective (Initial value)
B1 ~ B10: 1 to 10 times
After setting, press the

key. The ordinary display is recovered.

4. Continuous operation
After the completion of setting, regular operation like pattern number setup and others should be carried out.
At the end of sewing, origin retrieval of each motor is carried out for the X/Y / presser and thread trimmer /
needle thread clamp if origin retrieval effective has been selected as per 2. Then, automatic sewing is
restarted after the lapse of the rest time preset as per 1. above.
To stop continuous operation, the start switch should be turned ON during the rest time. [E 50] is displayed
and the machine is stopped.

144

4) CP-4 (Main motor rpm check)

Set up the rpm number of the sewing machine, drive only the main motor of the sewing machine at the preset
rpm level, and display the measured rpm number.
1. READY operation
In the first place, press the
key for the origin retrieval of the needle thread clamp and the presser and thread
trimmer motor. After operation for preparation, the sewing LED is lit.
2. Operation
When the
key is pressed, the sewing machine is
actuated at the preset rpm level.
If the rpm number is changed in the middle of sewing
machine operation, the speed can be changed by pressing the
key.
When the
stops.

key is pressed, the sewing machine

The preset rpm number or the actually measured rpm

number is displayed. Changeover is possible by pressing the
key.
Using the
and
keys, the rpm number can be
preset within the range of 400 to 2700 rpm. This setting
is possible even in the middle of sewing machine operation.

P1

P2

P3

P4

P5

The speed LED is unlit while the preset rpm number is

displayed, and is lit while the measured number is displayed. Changeover can be made by pressing the
key.
With the
key, the speed display can be changed
over between the preset and the measured rpm number.

145

5) CP-5 (Output check)

1. Operation

An output is generated while the

key is pressed.

The checking items can be changed with the

and
keys.
In regard to the items, refer to the section of IP-400 output
check.

P1

P2

P3

P4

P5

6) CP-6 (Presser and thread trimmer motor / origin sensor check)

The status of inching operation of the presser and thread trimmer motor, operation of origin retrieval, and the
presser origin and thread trimmer sensors is displayed.
1. READY operation
In the first place, press the
key for the origin retrieval of the needle thread clamp.
After operation for preparation, the sewing LED is lit.
2. Operation
According to the status of the thread trimmer sensor, 0 or 1 is displayed.
According to the status of the presser origin sensor, 0 or 1 is displayed.
Using the
and
keys, the presser and thread
trimmer motor can be driven by one pulse in the +/ direction.

P1

P2

P3

P4

P5

The
key is used to drive the presser and thread
trimmer motor to each preset position.
Presser lifting position
Presser lowering position (lowering position during
pedal operation)
Thread trimmer position
Presser lowering position (lowering position after
thread trimming)
When the
key is pressed while the P 5 key is
kept pressed, the motor is driven reversely.

1
2
3
4

The START Switch is used for the origin retrieval of the presser and thread trimmer motor.

146

7) CP-7 (Needle thread clamp motor / origin sensor check)

The status of inching operation of the needle thread clamp motor, operation of origin retrieval, and the thread
clamp origin and needle thread clamp sensors is displayed.
1. Operation
According to the status of the needle thread clamp sensor, 0 or 1 is displayed.
According to the status of the thread clamp origin sensor, 0 or 1 is displayed.
Using the
and
keys, the needle thread clamp
motor can be driven by one pulse in the +/ direction.
The

key is used to drive the needle thread clamp

motor to each preset position.

P1

P2

P3

P4

P5

1Standby position (front side)

2Needle thread bending position
3Needle thread clamp position
4Refuge position (rear side)

The START Switch is used for the origin retrieval of the needle thread clamp motor.

8) CP-8 (Intermediate presser adjustment)

The status of inching operation of the intermediate presser motor, operation of origin retrieval, and the thread
clamp origin and intermediate presser origin sensor is displayed.
1. Operation
According to the status of the intermediate presser origin sensor, 0 or 1 is
displayed.
Using the
and
keys, the needle thread clamp
motor can be driven by one pulse in the +/ direction.
The

key is used to drive the needle thread clamp

motor to each preset position.

P1

P2

P3

P4

P5

1Lower position at the height of 7mm during lowering

2Timing adjustment position
3Lower position at the height of 0mm during lowering
4Intermediate presser bar adjustment position

The START Switch is used for the origin retrieval of the intermediate presser motor.

147

9) CP-9 (Software version display)

The software versions of the PANEL Board, the MAIN Board, and the SDC Board are displayed.
Each version is expressed in a format of RR, VV, LL-xx. xx is used to indicate the specifications for special
orders, etc. Therefore, it is not indicated usually.
1. Operation

According to the item selection LED, the RVL display

(RR, VV, LL-xx) for the PANEL Board, the MAIN Board,
and the SDC Board, and also the model code display is
presented. The
and
keys can be used for the
scroll display.
Example) RVL 01.03.02
Example) AMS-210E

P1

P2

P3

P4

P5

The
key is used for the cyclic display of the PANEL
Board, the MAIN Board, and the SDC Board.
: Panel program
: Main program
: Servo program

The
key is used for the cyclic display of the RVL
display and the model code display.
When the LED is unlit: RVL display
When the LED is lit: Model code display

148

(4) For IP-400

1) Display of the check program screen
When the
key is continuously pressed for 3
seconds, the check program
(A) is displayed on
the screen. When this button is depressed, the check
program screen is displayed.

The check program comes in the ten items as specified

below.
Touch panel correction screen
The touch panel and button display positions are
corrected.
LCD check
Presence of any dot missing is checked for the liquid crystal display.
Input signal check
The status of switches and sensor inputs is displayed.

Main motor rpm check

When the sewing machine is started at the preset
rpm level, the measured rpm value is displayed.
Output check
Wiper and air output check is carried out.

XY motor / origin sensor check

The status of inching operation of the X/Y motor,
operation of origin retrieval, and the X/Y origin sensor is displayed.

149

Presser and thread trimmer motor / origin sensor check

The status of inching operation of the presser and
thread trimmer motor, operation of origin retrieval,
and the presser origin and presser sensor is displayed.
Needle thread clamp motor / origin sensor
check
The status of inching operation of the needle thread
clamp motor, operation of origin retrieval, and the
needle thread clamp origin and needle thread clamp
sensor is displayed.

Continuous operation
When the conditions of continuous operation have
been set up, the continuous operation mode is assumed.

Intermediate presser adjustment

The status of inching operation of the intermediate
presser motor, operation of origin retrieval, and the
intermediate presser origin sensor is displayed.

150

2) Touch panel correction

1. Display of the touch panel correction screen
When the touch panel correction button
(A) of
the check program screen is pressed, the touch panel
correction screen is displayed.

2. Pressing the bottom left position

Press the red circle
(C) located at the bottom left
of the screen. To complete correction, press the cancel button
(B).
B

3. Pressing the bottom right position

Press the red circle
(D) located at the bottom
right of the screen. To complete correction, press the
cancel button
(B).
B

151

4. Pressing the top left position

Press the red circle
(E) located at the top left of
the screen. To complete correction, press the cancel
button
(B).

5. Pressing the top right position

Press the red circle
(F) located at the top left of
the screen. To complete correction, press the cancel
button
(B).

6. Data saving
When all the four points have been pressed, the correction data are saved. At that time, the Power OFF
Prohibition screen is displayed.
The power supply must not be turned off while the
above-mentioned screen is displayed.
If the power supply is carelessly turned off, no correction data are saved.
After data saving, the check program screen is automatically displayed.

152

3) LCD check

1. Display of the LCD check screen

When the LCD check button
(A) is pressed on
the check program screen, the LCD check screen is
displayed.

2. Confirmation of LCD dot missing

The LCD check screen is displayed only in one color.
In this state, the LCD should be checked to freedom
from dot missing.
After this confirmation, press a proper position on
the screen. The LCD check screen is closed and the
check program screen is displayed.

153

4) Method of input signal check

1. Display of the input signal check screen
When the input signal check button
(A) is
pressed on the check program screen, the sensor
check screen is displayed.

2.

Input signal check

In the input signal check screen, the input conditions of various sensors can be confirmed.
For each sensor, the input status is displayed as
indicated by B.
The ON/OFF conditions are displayed as shown
below.

: ON condition
: OFF condition

Using the UP-DOWN buttons

the sensor that has been confirmed.

154

(C), display

The sensors provide the following 43 types of conditions:

No.

Pictograph

Contents of sensor

No.

Pictograph

Contents of sensor

DIPSW2-1

SDET sensor

DIPSW2-2

Head fall SW

DIPSW2-3

Air pressure SW

DIPSW2-4

Thread breakage sensor SW

Start SW (Pedal)

X motor origin sensor

Presser 1 SW (Pedal)

Y motor origin sensor

Presser 2 SW (Pedal)

Presser motor origin sensor

Presser 3 SW (Pedal)

Needle thread clamp motor

origin sensor

Presser 4 SW (Pedal)

Intermediate presser motor

origin sensor

Temporary stop SW

Presser motor sensor

AUDET sensor

Needle thread clamp motor

sensor

ADDET sensor

External input 1

DDET sensor

External input 2

UDET sensor

External input 3

TG sensor

External input 4

PDET sensor

External input 5

The DIPSW2 is the DIPSW located on the MAIN Board.

155

No.

Pictograph

Contents of sensor

No.

Pictograph

Contents of sensor

External input 6

External input 12

External input 7

External input 13

External input 8

External input 14

External input 9

External input 15

External input 10

External input 16

External input 11

156

5) Main motor rpm check

1. Display of the main motor rpm check screen
When the main motor rpm check button
(A) is
pressed on the check program screen, the main
motor rpm check screen is displayed.
A

2. Main motor operation and measured rpm value

check
Using the /+ buttons
(B, C), the rpm
number can be set up. When the button
(D) is
pressed, the sewing machine is operated at the preset speed. At that time, the measured rpm value is
displayed at
(E). When the SET button
(F)
is pressed, the sewing machine is stopped.

157

6) Method of output check

1. Display of the output check screen
When the output check button
(A) is pressed on
the check program screen, the output check screen
is displayed.

2. Output check
The output check screen can be used for the output
check of each position. Try to press the output check
button (B). While this button is pressed, the ON-status output is kept generated.

158

The output check display provides the following 17 types of positions:

No.

Pictograph

Contents

No.

Pictograph

Contents

Wiper

Air output 9

Air output 1

Air output 10

Air output 2

Air output 11

Air output 3

Air output 12

Air output 4

Air output 13

Air output 5

Air output 14

Air output 6

Air output 15

Air output 7

Air output 16

Air output 8

159

7) Method of XY motor / origin sensor check

1. Display of the XY motor / origin sensor check
screen
When the XY motor / origin sensor check button
(A) is pressed on the check program screen,
the XY motor / origin sensor check screen is displayed.

2. XY motor / origin sensor check

According to the status of the X/Y origin sensor, the
ON/OFF condition of the sensor is displayed in the
position of B.
When the Arrow-Mark button
(C) is pressed,
the X/Y motor can be driven by 0.05mm in the +/

direction.
C

(Caution) 1. Using the Start SW, origin retrieval of

the X/Y motors is effected for both
shafts.

160

8) Method of presser and thread trimmer motor /

origin sensor check
1.

Display of the presser and thread trimmer motor / origin sensor check screen
When the presser and thread trimmer motor / origin
sensor check button
(A) is pressed on the
check program screen, the presser and thread trimmer motor / origin sensor check screen is displayed.

B
C
G
H

J
K

2. Presser and thread trimmer motor / origin sensor check

According to the status of the thread trimmer sensor,
the ON/OFF condition of the thread trimmer sensor
is displayed in the position of B.
According to the status of the presser origin sensor,
the ON/OFF condition of the presser origin sensor is
displayed in the position of C.
Using the [+] and [] keys
(D, E), the
presser / thread trimmer motor can be driven by one
pulse.
When the fixed position moving button
(F) is
pressed, the presser / thread trimmer motor is driven
to any of the following fixed positions. A pictograph
indicating this position is displayed in gray.

G : Presser lifting position

H : Presser lowering position (lowering position
during pedal operation)
I : Thread trimmer position
J : Presser lowering position (lowering position
after thread trimming)
When the reverse rotation button
(K) is pressed,
driving is conducted in reverse direction. Using the
Start SW, origin retrieval of the presser / thread trimmer motor is effected.
(Caution) The Start Switch becomes effective after
the completion of origin retrieval for the
presser / thread trimmer motor.

161

9) Method of needle thread clamp motor / origin sensor check

B
C

H
J
I
F

1. Display of the needle thread clamp motor / origin

sensor check screen is displayed.
When the needle thread clamp motor / origin sensor
check button
(A) is pressed on the check
program screen, the needle thread clamp motor /
origin sensor check screen is displayed.

2. Needle thread clamp motor / origin sensor check

According to the status of the needle thread clamp
sensor, the ON/OFF condition of the needle thread
clamp origin sensor is displayed in the position of C.
According to the status of the needle thread clamp
origin sensor, the ON/OFF condition of the needle
thread clamp sensor is displayed in the position of
B.
Using the [+] and [] buttons
(D, E), the
needle thread clamp motor can be driven by one
pulse.
When the fixed position moving button
(F) is
pressed, the needle thread clamp motor is driven to
any of the following fixed positions. A pictograph indicating this position is reversed and displayed.

G
H
I
J

:
:
:
:

Standby position (front side)

Needle thread bending position
Needle thread clamp position
Refuge position (rear side)

Using the Start SW, origin retrieval of the needle

thread clamp motor is effected.
(Caution) The Start Switch becomes effective after
the completion of origin retrieval for the
needle thread clamp motor.

162

10) Method of continuous operation

1. Display of the continuous operation screen
When the continuous operation button
(A) is
pressed on the check program screen, the continuous operation screen is displayed.

2. Continuous operation
In the continuous operation screen, the continuous
operation mode is set up.
B : Intervals of operation (rest time)
C : Origin retrieval at the end of sewing
0 : No
1 : Every 100 runs
2 : Every time
D : Presser lifting, lowering (frequency)

When the READY key

is turned ON, continuous
operation is started.
If the READY key is turned ON again in the middle of
continuous operation, continuous operation is
stopped.

163

11) Method of intermediate presser motor / origin

sensor check

1. Display of the intermediate presser motor / origin sensor check screen

When the intermediate presser motor / origin sensor
check button
(A) is pressed on the check
program screen, the intermediate presser motor /
origin sensor check screen is displayed.

2. Intermediate presser motor / origin sensor check

According to the status of the intermediate presser
origin sensor, the ON/OFF condition of the intermediate presser origin sensor is displayed in the position of B.
Using the [+] and [] buttons
(C, D), the
intermediate presser motor can be driven by one
pulse.
When the fixed position moving button
(E) is
pressed, the intermediate presser motor is driven to
any of the following fixed positions. A pictograph indicating this position is reversed and displayed.

B
G
H
I

F : Lower position at the height of 7mm during

lowering
G : Timing adjustment position
H : Lower position at the height of 0mm during
lowering
I : Intermediate presser bar adjustment position

The START Switch is used for the origin retrieval of

the intermediate presser motor.

164

7. Printed wiring board and dip switch

(1) Various printed wiring boards
1) FLT-T board

Single-phase 100V~120V
3-phase 200V~240V

Pulse generation is carried out for the

purposes of power supply rectification,
noise reduction, and the detection of a
momentary interruption

CN1 : Power input Power switch

In the signal-phase mode, the
power supply is connected to
Pins 4-5. In the 3-phase mode,
the power supply is connected
to Pins 4-5-6.

Voltage changeover
Connected to 100V side
for 100V~120V or to
200V side for 200V~240V.

1
CN2 : Power output MAIN board
CN3: Momentary interruption
detection signal MAIN board

165

2) FLT-S board

Single-phase 200V~240V

Pulse generation is carried out for the purposes of power supply rectification, noise reduction, and the detection
of a momentary interruption

CN1: Power input Power switch

Since single-phase specifications are
adopted, the power supply is connected to
Pins 4-5.

4
C10

C9

CN2 : Power output MAIN board

CN3: Momentary interruption
detection signal MAIN board

166

3) SDC board
The power supply is generated and error check is carried out. Main shaft control is effected, receiving the commands from the MAIN board.
F4: 4A
Fuse fixed to the
board
For +48V source
primary

F1: 15A
Time lag fuse
For +48V

F2: 3.15A
Time lag fuse
For +33V

F5: 4A
Fuse fixed to the
board
For +33V source
primary

F3: 2A
Fast-blow type fuse
For +24V
CN10: 24V for the FAN
CN11: Power connector MAIN board
+5V, +12V, +24V, +33V, +48V

167

CN18: For IPM temperature sensor

LED3: For operation and error check
LED4: For power
supply check

DIPSW
2-1: For writing-off
2-2: For mode setting-off
2-3: For mode setting-off
2-4: For mode setting-off
CN13: For momentary interruption
detection FLT board
DIPSW
1-1: For testing-off
1-2: For testing-off
1-3: For testing-off
1-4: Penetration force-off

CN17: For power supply

FLT board

CN16: For Main shaft motor

power Main shaft motor

CN14: For Main shaft encoder

Main shaft motor
CN15: For MAIN communication
MAIN board

4) LED3 for SDC board error check

No. of LED3 flashes

Error description

Display of operation panel

Remarks

Turn on

Nil

Dimly turn on in ordinary state

Main shaft motor lock

E007

Failure in revolving for 2 seconds

Error in phase Z

E303

Failure in phase Z detection

About 1.5 turns

Error in phases A and B

E730

Failure in phases A and B detection

About 0.5 turns

Motor position sensor error

E731

Logical error in U, V, W

IPM error

E901

Error output generation from IPM

Undervoltage

E813

Source voltage -20% or more

Motor reverse rotation

E733

Irregular motor revolutions

Overvoltage

E811

Source voltage +20% or more

Power interruption

Display disabled

Power interruption of 40ms or more

10

Not used

11

+85V power system error E903

SDC board fuse F1 blow-off

12

+33V power system error E904

SDC board fuse F2 blow-off

13

Overheasting

E905

Radiator panel of SDC boaed heated

at 85C or higher

14

Not used

15

Communication erroe

E916

Failure in comminication with the

MAIN board

168

5) MAIN board
The board controls pulse motors, active tension, wipers, etc. for 5-axis separately and memory switch and other functions totally.

CN32: For the SDC circuit board

CN71: X feed pulse motor
(Red)
CN40: For analog pedal
(not integrated)
CN75: Thread clamp pulse motor
(White)
CN39: Active tension
(Yellow)

169

CN47: Wiper
(White)
CN31: Power SDC circuit board
+5V, +12V, +24V, +33V, +48V
CN51: Foot switch
(White)
CN52: For pneumatic switch
(White)

CN74: Feeding frame/thread

trimmer pulse motor (White)

CN34: Operation panel

IP-400/CP-20
CN38: For INT circuit board (machine head)
DIPSW 3-1: For writing-off
3-2: For writing-off
3-3: For writing-off
3-4: Not connected-off
DIPSW 2-1: Not used-off
2-2: Not used-off
2-3: Not used-off
2-4: For EE-PROM clearing-off
LD1: For operation display ON to
Model communication : lights up
CN80, CN81, CN82: Switch input (option) (not integrated)

CN78, CN83: Pneumatic output (option)

(not integrated)

CN84: Pneumatic output

(Black)
CN72: Intermediate presser pulse motor
(Blue)

CN79: Optional switch input

(Red)
CN73: Y-axis pulse motor
(White)

6) INT board
The board relays head sensor signals and transmits head model information to the MAIN board.

CN70: Intermediate presser origin (White)

CN65: Thread clamp origin, thread

clamp position (Yellow)

CN64: Presser lifter origin sensor (Black)

CN63: Y feed origin sensor (Yellow)

CN69: Temporary stop (Black)
CN71: For FAN (not integrated)

170
CN62: X feed origin sensor (Red)
CN68: Thread trimming detection (White)
CN66: Thread trimmer position (Red)

CN67: Safety switch (Red)

7) CP-20 Panel Board

The Panel board accommodates the display LEDs, switch buzzer, etc. together with the Smart Media sockets.

7-segment LED

SW13: Switch for the Smart Media

The Smart Media is not identified unless this switch is turned ON.

Buzzer

171

CN100: Connector for main unit connection

LED

Switch

Smart Media slot

DIPSW
1-1: For program writing-off
1-2: For program writing-off

8) IP-400 Panel Board

The Panel board is provided with the color LCD driver circuit, backlight power supply, CPU memories, etc., intended to support input and production control.

CN105: Connector for LCD panel connection

Socket for the Smart Media

Switch for the Smart Media (Rear SW2)
The Smart Media is not identified unless
this switch is turned ON.

DIPSW
1-1: For program writing-off
1-2: For program writing-off
1-3: For program writing-off
1-4: Not connected-off

CN101: Switch connector for production control

172

CN100: Connector for main unit connection

LD1: Status display LED

Kept blinking during CPU operation.

Backup batteries

CN109: Connector for touch panel connection

CN102: Connector for personal computer connection

The D-sub 9P cross-cable is used.

Buzzer
Backlight power supply
CN108: Connector for backlight connection

(2) Dipswitch setup

1. The penetration force is increased when 4 of
Dipswitch SW1
is turned ON on the SDC board
.
2. If the penetration force is insufficient for thick materials, this switch should be turned ON.
3. All other dipswitches should be turned OFF.

SDC board

SW1

(Caution) Dipswitch changeover should be done after the power supply has been turned off.

4. All dipswitches on the MAIN board are turned OFF.

MAIN board

SW3
1
2
3
4

O
N

SW2
1
2
3
4

O
N

173

8. Table of exchanging gauge parts according to sewing specifications

and needle size used
In accordance with the sewing condition, exchange the gauges referring to the following table.
Sewing spec.
and needle
size used

Gauge

S type when
delivered.
#11 to #14

Knit.
foundation
garment

H type when
delivered
#16 to #20

#21 to #22

#23 to #26

When thick
needle like MR
type is used.

Needle hole guide

B242621000F
B242621000A
1.6

B242621000C
1.6
(For knit)

B242621000B
2.0

3.0
B242621000G
3.0
(With counter bore)

B242621000D
2.4

Shuttle race ring

14103352
Needle guard 1.3 mm

14103659
Needle guard
1.7 mm

B1817210DAD
Needle guard
1.9 mm

Shuttle
40014964

40014965

Intermediate
presser
40023632
2.2

B1601210D0B
2.7

Tension controller
No.2 asm.
40010508

40029411

Thread trimmer
lever (small) asm.
B24152800A0

Needle bar
thread guide
40026883
2-hole

40026884
One hole

174

B1601210D0C
3.5

9. Option list
Name of parts

Type

1. needle hole guide

Part No

Needle hole guide (A) for lightweight material

Needle hole guide (B) for mediumweight material
Needle hole guide (C) for knitwear
Needle hole guide (D) for heavyweight material
Needle hole guide (F) for heavyweight material
Needle hole guide (G) for heavyweight material
Needle hole guide (H) for heavyweight material
Needle hole guide (H) (Countermeasures against stitch skipping)
Move the needle hole to have an
eccentricity of 0.5mm behind the
center in order to make the clearance
narrower in front of the needle and
wider behind it so that a loop can be
established easily.

2. Work clamp blank for

preventing slipping

B242621000A

A=1.6

B242621000B

A=2.0

B242621000C
B242621000D

A=1.6
A=2.4

B242621000F

A=3.0

B242621000G

A=3.0
(With counter bore)
A=3.0 (Eccentric)

B242621000H

Rubber sheet for work clamp

B2591220000

Sponge sheet for work clamp

B2564215000

Work clamp material (A)

B2587220000

Work clamp material (B)

B2588220000

Feed plate blank with knurl

B2556210D0A

r1 xr2 x t
168 x 131 x 1.2

Feed plate blank without knurl

B2556210D0B

r1 xr2 x t

B
3. Feed plate blank for
processing

Size (mm)

Ax Bxt
250 x 200 x1.5
AxBxt
300 x 200 x 1.5
AxBxt
380 x 240 x 1
AxBxt
380 x 240 x 1.5

r1
r2
168 x 131 x 1.2
t

r1
r2
4. Intermediate presser
A

Intermediate presser (A)

40023632

Intermediate presser (B)

B1601210D0BA

Intermediate presser (C)

B1601210D0CA

Intermediate presser (E)

B1601210D0E

Intermediate presser (F)

B1601210D0FA

175

A x B x rx L
2.2 x 3.6 x 6 x 29.5
A x B x rx L
2.7 x 4.1 x 6 x 29.5
A x B x rx L
3.5 x 5.5 x 6 x 29.5
A x B x rx L
1.6 x 2.6 x 6 x 29.5
A x B x rx L
2.2 x 3.6 x 9 x 29.5

Name of parts

Type

5. Feed plate blank

Part No

Size (mm)

Sheet A for work clamp (Velboren)

(Velboren)

B259522000A

AxBxt
1,000 x 675 x 1

Sheet B for work clamp

(Velboren)

B259522000B

AxBxt
1,000 x 675 x 3

Sheet C for work clamp

(Velboren)

B259522000C

AxBxt
1,000 x 675 x 2

Plastic feed plate inner plate

GMU12038000

AxBxt
140.8 x 72.5 x1

Aluminum feed plate inner plate

GMU12037000

AxBxt
140.6 x 72.5 x 1

Cassette holder installing base

B2593210DA0

Cassette holder assy

B2594210DA0

Plastic blank

B2557210DA0

Aluminum blank

GMU120350A0

6. Cassette holder

7. Feeding frame blank

176

Name of parts

Type

8. Blank for processing

Part No

Size (mm)

Separated type right blank of outer

frame with knurl

40035609

AxBxt
97 x 81.5 x 4

Separated type outer frame blank

without knurl
(Left and right are common.)

40035608

AxBxt
97 x 81.5 x 4

Separated type left blank of outer

frame with knurl

40035610

AxBxt
97 x 81.5 x 4

Presser blank of outer frame with

knurl

40035606

AxBxt
97 x 164 x 4

Presser blank of outer frame without

knurl

40035607

AxBxt
97 x 164 x 4

14103253
14103352
14103659
B1817210DAD

A=0.8
A=1.3
A=1.7
A=1.9

A
B

t
B

t
A
B

9. Shuttle race ring compl.

A
B (Standard)
C
D

177

Name of parts

Type

Part No

10. Compressor unit

CU-01

11. Economy type presser milling

unit

MU-12

12. Inverting clamp unit

(Caution) For the head of S type, it FU-05

is necessary to provide 40036596
for the AMS-210E air set
separately.

13. One-touch clamp device

For S type

B2585210DB0

For L type

B2586210DB0

14. Inverting intermediate presser Metal

blank
B

Plastic

178

Size (mm)

B43172100X0

AxBxt
135 x 58 x 3.2

162371T3

AxBxt
100 x 50 x4

Name of parts

Type

Part No

15. Inverting intermediate presser Without bearing

installing base

B
A

D431421WJ0B

AxB
5 x 24

D430121XB00

AxB
7 x 20

D431421WZ00

Ax B
7 x 24

D431421WK00

AxB
8 x 24

D431421YF00

AxB
10 x 20

D4314210000

AxB
10 x 24

Installing base
B4314210A00
Bearing
SB304000200
Washer
B4328210000

16. Wiper

Side-sweeping wiper assy

40035867

Side-sweeping wiper repeater cable

assy

40036668

179

Size (mm)

Name of parts

Type

Part No

17. Pedal switch

3-step pedal (PK47)

GPK470010AB

Relay cable for 3-step pedal

40033875

2-step pedal (PK78)

40033831

18. Needle cooler

(Caution) For the head of S type, it 40035692

is necessary to provide
for the AMS-210E air set
separately.

19. AMS-210E air set

To be exclusively used for Type S

180

40035693

Size (mm)

Name of parts
20. Pedal SW cable set

21. Mechanical valve unit

Type

Part No

Size (mm)

This is a kit intended to change

(40040138)
the tandem pedal (PK78) into the
3-switch pedal.

(Set Item No.)

Switch assembly

40040130

For further details,

refer to [(1) Method
of pedal switch cable
set connections].

Micro switch plate

11102308

Micro switch setscrew

SL4031691SC

2 pcs.

This unit is not applicable to the

machine head of Specification S.

(40042352)

(Unit Item No.)

For further details,
refer to [(2) Method of
mechanical valve unit
connections] and
[23. Pedal system]
of the parts list

181

(1) Method of pedal switch cable set connections

1. Parts
Pedal switch cable set (Item No.: 40040138)
No.

Item name
Presser micro switch plate
Micro switch setscrew
Switch assembly
Limit switch
Heat contraction tube 5 (15mm)
Heat contraction tube 5 (30mm)
Cable clip band
Cord bushing
Cabtyre cable 2-core (1830mm)
Pin terminal female

Item No.
11102308
SL4031691SC

HA001900000
E8760452G00
E8760452G00
EA9500B0200
M1013110000
HW500140000
HK03464000A

Quantity
1
2
1
(1)
(2)
(1)
(4)
(1)
(1)
(2)

o The item number of the switch assembly in the above table is 40040130.
o For more details of the pedal switch cable set in the above table, refer to [3. Switch assembly] and [6. Switch
mounting position diagram].

2. Switch mounting position

For more details, refer to [6. Switch mounting position diagram].

3. Switch assembly (Item No.: 40040130)

Connector pin No.

30mm
Black

CN88-7(Black)
CN88-2(White)
(White)

4. Memory switch modification

Level 1 change
No.
U81
U82
U85

Before change
0
0
1

After change
1
1
0

182

SW D

5. Operation control items

o The moving switch does not function unless the right pedal is trodden first.
o For more details, refer to [6. Switch mounting position diagram].

6. Switch mounting position diagram.

(Caution) The micro switch shall be mounted in parallel to the upper plane
of the pedal.
(The switch is fixed in the ON state.)
Connector pin
Connector pin
No. 7
No. 2
CN88
Connector

Black : No. 7

White : No. 2

183

(2) Method of mechanical valve unit connections

1. Remove once two setscrews , two washers (small)
, two spring washers
and two washers (large)
attached to mechanical valve unit . Refer to the
figure, and install 2-pedal (PK78) type
into hole A
of mechanical valve unit .

2. Connect the air tubes

,
which come from the
machine head, to the Y-type joint ,
respectively.
o Air tube
with label of 1A, 2A
Y-type joint
connected with the label of 3
of mechanical valve unit
with label of 1B, 2B
o Air tube
Y-type joint
connected with the label of 4
of mechanical valve unit

Stop plug

Stop plug

Connector
CN2

3. Install the air tube coming from mechanical valve unit

7 to A , and that from 8 to B respectively.
Attach two accessory stop plugs and the cords coming from the control box to the connectors CN1, CN2,
respectively.

Connector
CN1

and the regulator

4. Connect solenoid valve asm.
using long air tube supplied
as accessories.
(Caution) When the cable sage, fix it to the table using the staple supplied with the machine
as accessories.

184

10. Maintenance
(1) Replacing the fuse
The machine uses the following three fuses: (SDC
Board)
For pulse motor power supply protection
15A(time-lag fuse)
For solenoid and pulse motor power supply protection
3.15A (time-lag fuse)
For control power supply protection
2A (fast-blow type fuse)

185

(2) Changing the voltage specification

It is adaptable to the voltage of single phase 100V to 120V/3-phase 200V to 240V by changing the voltage changeover
connector mounted on FLT-T p.c.b.
(Caution) When the changing procedure is wrong, the control box will be broken. So, be very careful.
Changing procedure of the changeover connector
1. Turn OFF the power source with the power switch
after confirming that the sewing machine has stopped.
2. Draw out the power cord from the power plug socket
after confirming that the power switch is turned OFF.
Then wait for five minutes or more.
3. Remove the front cover.
4. Remove four screws fixing the rear cover of the control box and slowly open the rear cover.
A. In case of using with 3-phase 200V to 240V
Changing the changeover connector
Connect to 200V the 100/200V changeover connector of FLT-T p.c.b.
located on the side of the Box
Side of the control box.
Connect the crimp style terminal of AC input cord to
the power plug as shown in the figure.

(Plug side)
WHITE
BLACK
RED
GREEN/
YELLOW

WHITE
BLACK
RED
GREEN/
YELLOW

B. In case of using with single phase 100V to 120V

Changing the changeover connector
Connect to 100V the 100/200V changeover conneclocated on the side of the Box
tor of FLT-T p.c.b.
Side of the control box.
Connect the crimp style terminal of AC input cord to
the power plug as shown in the figure.
(Caution) Securely perform the insulation treatment
to the red terminal which is not used with
insulation tape or the like. (When the insulation is insufficient, there is a danger
of electric shock or leakage current.)

(Plug side)
WHITE
BLACK
RED
GREEN/
YELLOW

WHITE
BLACK
RED
GREEN/
YELLOW

C. In case of using with single phase 200V to 240V

Changing the changeover connector
Connect to 200V the 100/200V changeover connector of FLT-T p.c.b.
located on the side of the Box
Side of the control box.
Connect the crimp style terminal of AC input cord to
the power plug as shown in the figure.
(Caution) Securely perform the insulation treatment
to the red terminal which is not used with
insulation tape or the like. (When the insulation is insufficient, there is a danger
of electric shock or leakage current.)
5. Check that the change has been performed without
fail before closing the rear cover.
6. Be careful that the cord is not pinched between the
rear cover and the control box main unit.
Close the rear cover while pressing the lower side of
rear cover, and tighten four screws.

(Plug side)
WHITE
BLACK
RED
GREEN/
YELLOW

WHITE
BLACK
RED
GREEN/
YELLOW

186

(3) Greasing lock-tight parts

1. When the parts for greasing and grease sealing-in are disassembled and the operational frequency seems to be
higher than usual around these parts, grease should be replenished once every two years.
2. Recommendable grease
This sewing machine uses four types of grease as specified below. The recommendable brands of grease are
listed in (4) Parts to which greaselock-tight is applied. According to this information, replenish the most applicable grease to these parts.
* Use
Lithium Type consistency No. 2 for the parts where Grease is simply specified in (4) Parts to
which greaselock-tight is applied.
Penetration No. 2 lithium grease
This type of grease is used in general sliding parts.

Maker name

Brand name

Esso:

Listan 2, Beacon 2

Shell:

Albania

Nippon Oil Co., Ltd.:

Multinok 2, Epinok 2

Kyodo Oil Co., Ltd.:

Lisonix 2

Idemitsu Petrochemical Co., Ltd.:

Coronex 2

2 Templex N2 (Grease D) Used for the feeding gear block.

10g tube JUKI Part No.: 13525506

3 JUKI Grease A Used for high-speed sliding parts and their peripheral parts.
10g tube JUKI Part No.: 40006323
500g (IE-22) JUKI Part No.: 23640204

4 JUKI Grease B Used, in particular, for the specific areas with highly loaded parts. Important: this
grease must be replenished at the specified intervals of period, according to (5) Grease-up procedures
for the specified position.
10g tube JUKI Part No.: 40013640

3. Method of greasing
If no grease pump is available, fill a plastic oilcan with grease. Otherwise, an injector without a needle can be
conveniently used.
4. Miscellaneous
An injector to be used exclusively for coating / JUKI Part No. : GDS01007000
5. Application of Lock Tight
Apply Lock Tight 241 to section with the asterisk

187

(4) Parts to which grease lock-tight is applied

o MAIN SHAFT & NEEDLE BAR COMPONENTS

A
A
A

A
B

C
C

A : JUKI Grease A
B : JUKI Grease B
C : Grease

188

o PRESSER MECHANISM & PRESSER VARIABLE COMPONENTS (1)

B
B

B
B

B
B

A
B

B
B
B

B
B

A
B : JUKI Grease B
: Lock-tight 241

189

o PRESSER MECHANISM & PRESSER VARIABLE COMPONENTS (2)

B
B

B
B

B
B
B
B
C

B
B

B
C
B

B : JUKI Grease B
C : Grease

o WIPER MECHANISM COMPONENTS

C
C

C : Grease

190

o PRESSER PLATE & MANUAL PRESSER MECHANISM COMPONENTS

B
C
C

B
B
B

C
B

B
C

A : JUKI Grease A
B : JUKI Grease B
C : Grease

o TENSION RELESASE & THREAD TENSION COMPONENTS

C
C

C : Grease

191

o SHUTTLE DRIVER SHAFT COMPONENTS

A
A

A : JUKI Grease A

o FRAME & MISCELLANEOUS COVER COMPONENTS (2)

A : JUKI Grease A

192

o TENSION RELEASE & THREAD TRIMMER MECHANISM COMPONENTS

A
A

A
A

A : JUKI Grease A
C : Grease
o THREAD CLAMP COMPONENTS

C
C

C
C

C : Grease

193

o X-Y COMPONENTS

D
B

C
C
C

B : JUKI Grease B
C : Grease
D : Grease D

194

o CLOTH FEED MECHANISM COMPONENTS (FOR AMS-210EHS, ESS)

C
C

C
B
C

C
C

C
C

B : JUKI Grease B
C : Grease
o CLOTH FEED MECHANISM COMPONENTS (FOR AMS-210EHL, ESL)

C
C

C
C
C
C

195

B : JUKI Grease B
C : Grease

(5) Replenishing the designated places with grease

*

Perform grease supplement when the errors below are displayed or once a year (either one which is
earlier). After performing grease supplement, call memory switch No. 245 and set the value to 0
with the reset key.
When the sewing machine has been used for a certain number or times of sewing, error code No. E220 is
displayed on the operation panel at the time of turning ON the power. This display informs the operator of the
time of replenishing the designated places with grease. Be sure to replenish the places with the grease below.
Then call the memory switch No. 245 and set it to 0 with the RESET key.
Even after the display of the error No. E220, when the RESET key is pressed, the error is released, and the
sewing machine can be continuously used. Afterwards, however, the error No. E220 is displayed every time
the power is turned ON.
In addition, when the sewing machine is used further for a certain period of time after the display of error No.
E220, the error No. E221 is displayed and the sewing machine fails to operate since the error cannot be
released even when the RESET key is pressed.
When the error No. E221 is displayed, be sure to replenish the designated places below with grease.
Then start up the memory switch and set No. 245 to 0 with the RESET key.
(Caution) 1. After replenishing the places with grease, the error No. E220 or No. E221 is displayed
again unless the memory switch No. 245 is changed to 0.
2. Use grease tube (JUKI grease B Part No. : 40013640) supplied as accessories to replenish the designated places below with grease. If grease other than the designated one is
replenished, damage of components will be caused.

WARNING:
Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start
of the sewing machine.
1) Replenishing the eccentric cam section with grease
1. Open the upside cover
and remove the JUKI
grease B .
2. Remove rubber cap
located on the side of eccentric cam
. Then replenish there with JUKI grease
B .

196

2) Replenishing the oscillator pin section with grease

1. Tilt the machine head and remove the grease cover
.
2. Fill joint
supplied as an accessory with JUKI
Grease B.
3. Remove setscrew
in oscillator gear
and screw
in joint
into the screw hole.
4. Screw in screw
supplied as accessories to the
joint
and replenish there with JUKI grease B.
5. Securely tighten setscrew
which has been removed after replenishing with the grease.

3) Grease supplement to the face plate section

1. Open the face plate cover.
2. Supplement JUKI grease B to the felt section (3
places) and the hinge screws around them.

4) Grease supplement to X guide shaft bearing

1. At the same time, apply JUKI grease B to the rear
faces of X guide shaft
and presser plate .

197

11. Error code list

Error code

Pict

Description of error

How to recover Place of recovery

E001

Data is initializes
(EEPROM of MAIN CPU)

Turn OFF
the power

E007

Main shaft motor-lock

When large needle resistance sewing product is sewn

Turn OFF
the power

E008

Head connector abnormality

Memory of machine head cannot be read.

Turn OFF
the power

E010

Pattern No. error

Pattern No. which is backed up is not registered to
data ROM,or setting of reading inoperative is
performed.

Possible to
Previous
re-enter after screen
reset.

E011

External media not inserted

External media is not inserted.

Possible to
Previous
re-enter after screen
reset.

E012

Read error
Data read from external media cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E013

Write error
Data write from external media cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E014

Write protect
External media is in the write prohibition state

Possible to
re-start after
reset.

Previous
screen

E015

Format error
Format cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E016

External media capacity over

Capacity of external media is short.

Possible to
re-start after
reset.

Previous
screen

198

Error code

Pict

Description of error

How to recover Place of recovery

E017

EEP-ROM capacity over

When the mounted EEP-ROM is different in type.

E018

Type of EEP-ROM is different.

When the mounted EEP-ROM is different in type.

E019

File size over

Pattern data size over

Possible to
re-start after
reset.

Previous
screen

E022

File No. error

There is no designated file in the server or external
media.

Possible to
re-start after
reset.

Previous
screen

E024

Pattern data size over

When sewing cannot be performed since the size
of downloaded sewing data is too large.

Possible to
re-start after
reset.

Data input
screen

E027

Read error
Data read from server cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E028

Write error
Data write to the server cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E029

Smart media slot release error

Lid of smart media slot is open.

Possible to
re-start after
reset.

Previous
screen

E030

Needle bar upper position failure

Turn hand pulley to bring needle bar to its UP
position

Turn hand
pulley to
bring needle
bar to its UP
position.

Data input
screen

E031

Air pressure drop

When the air pressure is lowered.

Possible to
re-start after
reset.

Data input
screen

199

Possible to
re-start after
reset.

Previous
screen

Previous
screen

Error code

Pict

Description of error

How to recover Place of recovery

E032

File interchanging error

File cannot be read.

Possible to
re-start after
reset.

Data input
screen

E040

Sewing area over

When the sewing area is exceeded

Possible to
re-start after
reset.

Sewing
screen

E042

Operation cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E043

Enlarging error
Sewing pitch exceeds Max. pitch.

Possible to
re-start after
reset.

Data input
screen

E045

Pattern data error

These pattern data are not applicable.

Possible to
re-start after
reset.

Data input
screen

E050

Stop switch
When stop switch is pressed during machine
running.

Possible to
re-start after
reset.

Step
screen

E052

Thread breakage detection error

When thread breakage is detected.

Possible to
re-start after
reset.

Step
screen

E061

Memory switch data error

Memory switch data is broken or revision is old.

Turn OFF
the power.

E063

Head discrimination error

Head discrimination and the kind of control box
are different.

Turn OFF
the power.

E220

Grease-up warning
At the time of operation of 100 million stitches
Refer to 10.-(5) Replenishing the designated
places with grease.

Possible to
re-start after
reset.

Data input
screen

E221

Grease-up error
At he time of operation of 120 million stitches
The sewing machine is put in the sewing-impossible status.
It is possible to clear with memory switch
.
Refer to 10.-(5) Replenishing the designated
places with grease.

Possible to
re-start after
reset.

Data input
screen

200

Error code

Pict

Description of error

How to recover Place of recovery

E302

Confirmation of tilt of machine head

When tilt of machine head sensor is OFF.

Possible to
re-start after
reset.

E303

Phase Z detection error

Detection of the upper dead point is impossible for
the sewing machine.

Turn OFF
the power.

E305

Thread trimmer knife position error

The thread trimmer knife is not in the regular position.

Turn OFF
the power.

E306

Thread clamp position error

Thread clamp unit is not in the regular position.

Turn OFF
the power

E307

External input command time out error

Input is not performed for a fixed period of time with
the external input command of vector data.

Possible to
re-start after
reset.

E308

Time-out error of wait terminal

There is no input to wait terminal for a certain period
of time.

Turn OFF
the power

E431

Outer presser is rising.

Possible to
re-start after
reset.

Previous
screen

E432

Proper operation has not been performed.

Possible to
re-start after
reset.

Previous
screen

E433

Number of stitches has exceeded the limit.

Possible to
re-start after
reset.

Previous
screen

E434

Hadware error has occurred.

Possible to
re-start after
reset.

Previous
screen

E437

Function cannot be selected.

Possible to
re-start after
reset.

Previous
screen

201

Previous
screen

Data input
screen

Data input
screen

Error code

Pict

Description of error

How to recover Place of recovery

E438

Execution cannot be performed.

Possible to
re-start after
reset.

Previous
screen

E441

Back-up data does not exist.

Possible to
re-start after
reset.

Previous
screen

E703

Panel is connected to the machine other than

supposed. (Machine type error)
When machine type code of system is improper in
case of initial communication.

Possible to
Commnunication
rewrite program screen
after pressing
down
communication
switch.

E704

Inconsistency of system version

When version of system software is improper in
case of initial communication.

Commnunication
Possible to
rewrite program screen
down
communication
switch.

E730

Main shaft motor encoder defectiveness or

phase-out
When encoder of sewing machine motor is
abnormal.

Turn OFF
the power

E731

Main motor hole sensor defectiveness or

position sensor defectiveness
When hole sensor or position sensor of sewing
machine is defective.

Turn OFF
the power.

E733

Reverse rotation of main shaft motor

When sewing machine motor rotates in reverse
direction.

Turn OFF
the power.

E802

Power instantaneous cut detection

When input power is instantaneously OFF.

Turn OFF
the power.

E811

Over voltage
When input power is more than the specified value.

Turn OFF
the power.

E813

Low voltage
When input voltage is 150V or less.

Turn OFF
the power.

E901

Abnormality of main shaft motor IPM

When IPM of servo control p.c.b. is abnormal.

Turn OFF
the power.

202

Error code

Pict

Description of error

How to recover Place of recovery

E903

Abnormality of stepping motor power

When stepping motor power of servo control p.c.b.
fluctuates 15% or more.

Turn OFF
the power.

E904

Abnormality of solenoid power

When solenoid power of servo control p.c.b.
fluctuates 15% or more.

Turn OFF
the power.

E905

Heat sink temperature for SERVO CONTROL p.c.b. Turn OFF

fabnormality
the power.
Turn ON the power again after taking overheat time
of SERVO CONTROL p.c.b.

E907

X feed motor origin retrieval error

When origin sensor signal is not inputted at the time
of origin retrieval motion.

Turn OFF
the power.

E908

Y-feed motor origin retrieval error

When origin sensor signal is not inputted at the
time of origin retrieval motion.

Turn OFF
the power.

E910

Presser motor origin retrieval error

When origin sensor signal is not inputted at the
time of origin retrieval motion.

Turn OFF
the power.

E913

Thread clamp origin retrieval error

When origin sensor signal is not inputted at the time
of origin retrieval motion.

Turn OFF
the power.

E914

Feed defective error

Timing lag between feed and main shaft occurs.

Turn OFF
the power.

E915

Abnormality of communication between

operation panel and main CPU
When abnormality occurs in data communication.

Turn OFF
the power.

E916

Abnormality of communication between main

CPU and main shaft CPU
When abnormality occurs in data communication.

Turn OFF
the power.

E917

Failure of communication between operation

panel and personal computer
When abnormality occurs in data communication.

Possible to
re-start after
reset.

203

Error code

Pict

Description of error

How to recover Place of recovery

E918

MAIN board overheat

Overheat of MAIN board
Turn ON the power again after taking time.

Turn OFF
the power.

E925

Intermediate presser motor origin retrieval error

Origin sensor of intermediate presser motor does not
change at the time of origin retrieval.

Turn OFF
the power.

E943

MAIN EEP-ROM trouble

When data writing to EEP-ROM cannot be
performed.

Turn OFF
the power.

E946

Defective EEP-ROM writing of HEAD RELAY board

When data writing to EEP-ROM cannot be performed.

Turn OFF
the power.

E948

F-ROM abnormality
When erase or writing of program cannot be
performed at the time of downloading program.

Turn OFF
the power.

204

12. Message list

Message No.

Display

Display message

Description

M520

Erase confirmation of Users pattern

Erase is performed. OK?

M521

Erase confirmation of pattern button

Erase is performed. OK?

M522

Erase confirmation cycle pattern

Erase is performed. OK?

M523

Erase confirmation of backup data

Pattern data is not stored in memory.
Erase is OK?

M528

Overwriting confirmation of users

pattern
Overwriting is performed. OK?

M529

Overwriting confirmation of smart

media
Overwriting is performed. OK?

M530

Overwriting confirmation of vector

data of panel/M3 data/sewing
standard format data/simplified
program data
Overwriting is performed. OK?

M531

Overwriting confirmation of vector

data of smart media/M3 data/
sewingstandard format data/
simplified program data
Overwriting is performed. OK?

205

Message No.

Display

Display message

Description

M532

Overwriting confirmation of vector

data on personal computer/M3
data/sewingstandard format data/
simplified program data
Overwriting is performed. OK?

M534

Overwriting confirmation of
adjustment data of smart media
and all machine data
Overwriting is performed. OK?

M535

Overwriting confirmation of
adjustment data on personal
computer and all machine data
Overwriting is performed. OK?

M537

Delection confirmation of thread

tension command
Delecting is performed. OK?

M538

Delection confirmation of
intermediate presser increase/
decrease value
Delecting is performed. OK?

M542

Format confirmation
Formatting is performed. OK?

M544

Data corresponding to panel does

not exist.
Data does not exist.

M545

Data corresponding to smart

media does not exist.
Data does not exist.

206

Message No.

Display

Display message

Description

M546

Data corresponding to personal

computer does not exist.
Data does not exist.

M547

Overwriting prohibition on pattern

data
Overwriting cannot be performed
since data exists.

M548

Overwriting prohibition on smart

media data
Overwriting cannot be performed
since data exists.

M549

Overwriting prohibition on data on

personal computer
Overwriting cannot be performed
since data exists.

M550

Backup data information on main

body input
There is back-up data of body input.

M653

During formatting
Formatting is performed.

M669

During data reading

Data is being read.

M670

During data writing

Data is being written.

M671

During data converting

Data is being converted.

207

13. Troubles and corrective measures

(1) Mechanical parts
Trouble

Cause (1)

Cause (2)

Check and corrective measures

1. Sewing machine locked

1-1) Large needle compared with

the hole diameter of the needle
hole guide

Replace the needle hole guide.

2. Deformation in sewn patterns

2-1) X timing belt tension is

maladjusted.

Adjust the X timing belt tension.

2-2) Backlash of the X feed motor

gear is maladjusted.

Adjust the position of X feed motor.

2-3) Backlash of the Y feed motor

gear is maladjusted.

Adjust the position of Y feed motor.

2-4) Traveling torque in X direction

or Y direction is excessive.

208
2-5) Pressing pressure is too low.
(Air specification)

3. There is no coincidence between

the input origin and the sewing origin.

4 Feeding action does not stop even

after exceeding the sewing range.

5. The amount of lifting is small for the

outer frame of the cloth presser.

4-A) Pressure of the X-Y table is

too high.

Adjust the pressure of the X-Y table.

4-B) Height or horizontality is

inadequate for the needle bar
auxiliary cover.

Adjust the height or the horizontality of the needle

bar auxiliary cover.

5-A)Regulator is maladjusted.

Adjust the regulator.

5-B) Supply air pressure is too low.

Adjust the supply air pressure.

3-1) Inadequate adjustment of the

X origin sensor

Adjust the position of X origin sensor.

3-2) Inadequate adjustment of the

Y origin sensor

Adjust the position of Y origin sensor.

4-1) Inadequate adjustment of the

X origin sensor

Adjust the position of X origin sensor.

4-2) Inadequate adjustment of the

Y origin sensor

Adjust the position of Y origin sensor.

5-1) Inadequate adjustment of the

height of the presser

Adjust the height of the presser.

Trouble
6. The outer frame of the cloth presser
cannot be lifted or lowered.

Cause (1)

Cause (2)

6-1) The thread trimmer cam

screw is loose.
(Motor specification only)
6-2) Presser pulse motor malfunction
(motor specifications only)

6-3) Defective board

Decide the position of the thread trimmer cam screw

and fix it.
2-A) The presser pulse motor is
out of order.

Replace the presser pulse motor.

2-B) Connection of presser pulse

motor is improper.

Check the connector connections.

3-A) The board is out of order.

Replace the board.

3-B) Connector connections are

improper.

Check the connector connections.

6-4) There are inadequate fitting

conditions among the work feed
bar, the link, and the face plate.

209
7. The intermediate presser does not
rise after sewing.

Check and corrective measures

Examine the positions for greasing.

The sewing material is not pressed completely by the
outer frame as a whole.

6-5) Supply air pressure is too low.

(Air specification only)

Adjust the supply air pressure.

6-6) Inadequate adjustment of the

regulator (air specifications only)

Adjust the regulator.

6-7) Solenoid valve malfunction

(air specifications only

Reolace the solenoid valve.

6-8) Inadequate adjustment of the

speed controller
(air specifications only)

Adjust the speed controller.

7-1) There are some inadequate

fitting conditions in the intermedi
ate presser link mechanism.

Check for the inadequate fitting and rattling conditions

in the link mechanism.
Examine the positions for greasing.

7-2) Intermediate presser variable

is maladjusted.

Adjust the intermediate presser variable.

7-3) Intermediate presser pulse

motor malfunction

7-4) Defective board

3-A) Intermediate presser pulse

motor is out of order.

Replace the intermediate presser pulse motor.

3-B) Connection of intermediate

presser pulse motor is
improper.

Check the connector connections.

4-A) The board is out of order.

Replace the board.

4-B) Connector connections are

improper.

Check the connector connections.

Trouble
8. The intermediate presser does not
work during sewing.

Cause (1)

Check and corrective measures

8-1) There are some inadequate

fitting conditions in the intermediate presser link mechanism.

Check for the inadequate fitting and rattling conditions

in the link mechanism.
Examine the positions for greasing.

8-2) Intermediate presser variable

is maladjusted.

Intermediate presser variable adjustments.

8-3) Intermediate presser pulse

motor malfunction

8-4) Defective board

210

9. Unusual sound is generated from

the face section.

Cause (2)

3-A) Intermediate presser pulse

motor is out of order.

Replace the intermediate presser pulse motor.

3-B) Connection of intermediate

presser pulse motor is improper.

Check the connector connections.

4-A) The board is out of order.

Replace the board.

4-B) Connector connections are

improper.

Check the connector connections.

8-5) The intermediate presser

stroke has decreased to 0mm.

Adjust the intermediate presser variable stroke.

9-1) The clearance is too much

between the inner hook and
the driver.

Adjust the clearance between the inner hook and the

driver.

9-2) The intermediate presser bar

connection comes in contact
with the lower metal of the
intermediate presser needle bar.

Adjust the intermediate presser adjusting arm.

9-3) The intermediate presser comes

in contact with the throat plate.

3-A) Inadequate adjustment of the

height of the intermediate presser

Adjust the height of the intermediate presser.

9-4) The intermediate presser comes

in contact with the cloth presser.

Adjust the presser.

9-5) Intermediate presser variable

is maladjusted.

Intermediate presser variable adjustments.

9-6) Intermediate presser pulse

motor malfunction

9-7) Defective board

6-A) Intermediate presser pulse

motor is out of order.

Replace the intermediate presser pulse motor.

6-B) Connection of intermediate

presser pulse motor is improper.

Check the connector connections.

7-A) The board is out of order.

Replace the board.

7-B) Connector connections are

improper.

Check the connector connections.

Trouble
10. Even when the sewing machine is
started, it goes to stop soon.

Cause (1)

Cause (2)

Check and corrective measures

Pass the needle thread.

10-2) Position of the thread breakage

detecting plate is wrong.

Adjust the position of the thread breakage detecting

plate.

11. Even though the needle thread is

broken, the sewing machine does
not stop.

11-1) Position of the thread

breakage detecting plate is
wrong.

Adjust the position of the thread breakage detecting

plate.

12. Wiper cannot spread a thread

12-1) Interference between wiper

and needle

1-A) Wiper mounting position is

inadequate.

Adjust the wiper position.

12-2) Interference between wiper

and intermediate presser

2-A) Inadequate adjustment of the

height of the intermediate
presser

Adjust the height of the intermediate presser.

2-B) Wiper mounting position is

inadequate.

Adjust the wiper position.

12-3) There is no clearance between

the needle and intermediate
presser to pass the wiper.

3-A) The cloth thickness permitting

the use of a wiper is exceeded.

Use the lower wipe-out sequence.

12-4) The wiper does not move

after thread trimming.

4-A) The wiper switch is turned

OFF.

Turn the wiper switch ON.

211

10-1) The needle thread is not

hooked.

13. Severe vibration

13-1) Position of the crank balancer

is wrong.

Define the correct crank balancer position.

(2) Sewing conditions

Trouble
1. Thread comes off at the start of
sewing

Cause (1)
1-1) Stitch skipping at the start of
sewing

Cause (2)
1-A) Too much clearance between
needle and hook.

Check and corrective measures

Set the clearance at 0.05 to 0.1mm between the needle and the hook.
Set up soft start at the beginning of sewing.

1-2) Length of thread remaining

at the needle is not sufficient.

212
1-3) Length of bobbin thread remaining is not sufficient.

To the next page

1-B) Penetration registance of the

thread against the cloth is small.

Use a thinner needle. (Lower the needle count to be

used.)

2-A) Tension controller No. 1 provides

an excessive tension.

Properly adjust the tension controller No. 1.

2-B) Floating of the AT thread

tension disc is insufficient.

Adjust the amount of AT thread tension floating.

2-C) Stroke of the thread take-up

spring is excessive.

Adjust the stroke of the thread take-up spring.

2-D) The thread take-up spring

tension is insufficient.

Adjust the thread take-up spring tension.

2-E) Level difference between the

needle hole guide and the
counter knife is excessively high.

Adjust the height of the counter knife.

2-F) Needle thread tension is high

and the thread is excessively
stretched.

Adjust the needle thread tension.

2-G)Thread spreading section of

the moving knife has scratches.

Polish the thread spreading section of the moving

knife with buff or replace the knife.

3-A) Level difference between the

needle hole guide and the
counter knife is excessively high.

Adjust the height of the counter knife.

(Otherwise, widen the gap.)

3-B) Lower face of the needle hole

guide has scratches.

Polish the needle hole guide with a buff or replace it.

3-C) Thread spreading section of the

moving knife has scratches.

Polish the thread spreading section of the moving

knife with buff or replace the knife.

3-D) Shuttle upper spring has

scratches.

Polish the shuttle upper race with a buff or replace

it.

3-E) The bobbin thread tension is

excessive.

Adjust the bobbin thread tension.

3-F) The bobbin or bobbin case

has scratches.

Polish it with a buff or replace it.

Trouble

Cause (1)

Cause (2)

Check and corrective measures

From the previous page

1-4) Material to be sewn is not
properly stretched.
1-5) Unstable needle thread clamp

Remove the slack of the material to be sewn.

5-A) Thread tends to be extended
or sliding efficiency is worse.

Increase the needle thread clamp needle number to

3~4 stitches.
Lower the speed of the first stitch. (600 ~ 1000rpm)

5-B) Pitch of the first stitch is too small.

Lower the needle thread tension of the first stitch.

Increase the pitch of the first stitch.

1-6) Threading the needle bar

thread guide is wrong.

Refer to the item Threading the needle bar thread

Guide.

1-7) Bobbin runs idle and the bobbin

thread is drawn out.

Use a stronger idling prevention spring.

7-A) Initial positioning of the moving knife is inadequate.

213

2. Needle breakage

Adjust the initial position of the moving knife.

2-1) Inadequate clearance between

the shuttle driver and the
needle

Adjust the clearance between needle and shuttle driver.

2-2) Inadequate clearance between

the needle and the inner hook.

Adjust the clearance between the needle and the

inner hook.

2-3) Feed timing is defective

3-A) Too late feed timing for cloth

thickness

Change the feed timing by the use of the memory switch.

2-4) Needle coming in contact

with the moving knife

Adjust the moving knife position.

2-5) Needle coming in contact

with the wiper

Adjust the wiper position.

2-6) Needle is bent

6-A) The needle thread tension is

too high.

Adjust the tension to a proper level.

2-7) Needle is too thin.

Change the needle No. to the suitable one to the material.

2-8) Interference between work

clamp foot and needle

Adjust the work clamp foot (feed bracket) position.

Trouble
3. Stitch Skipping

Cause (1)

Cause (2)

3-1) Too much clearance between

the needle and the inner hook.

Adjust the clearance between needle and inner hook.

3-2) Inadequate timing adjustment

for the needle and the inner hook.

Adjust timing for the needle and the inner hook.

3-3) Inadequate clearance between

the shuttle driver and the needle

Adjust the clearance between needle and shuttle driver.

3-4) Material to be sewn is not

properly stretched.

4. Needle thread breakage

Check and corrective measures

4-A) Too much clearance between

the work clamp foot and
sewing object

Adjust the work clamp foot height.

Remove the slackness of the sewing object.

3-5) Needle is bent or blunt.

Replace the needle.

3-6) Loop of the needle thread

falls down.

Attach the needle with the long groove orienting slightly

to the right. (Approximately 20)

4-1) Stratches on the inner hook

214

A
B

4-2) Thread enters into the shuttle.

6-A) Feed timing is too fast.

Change the feed timing by the use of the memory switch.

1-A) Scratches on section A

(Contact of the inner hook with
the needle)

After polishing the blade point of the inner hook with

oilstone, polish it with polishing powder. Properly adjust
the clearance between the needle and the inner hook.

1-B) Scratches on section B

(Scratches occur when the
needle is bent or broken.)

After polishing the blade point of the inner hook, polish it

with polishing powder.

1-C) Scratches on section C

(Needle scratches the inner hook
when removing the inner hook.)

After polishing the blade point of the inner hook, polish it

with polishing powder.

1-D) Scratches on section

After polishing the blade point of the inner hook, polish it

with polishing powder.

2-A) Position of the shuttle upper

spring is wrong.

Properly adjust the position of the shuttle upper

spring.

2-B) Blade point section

shuttle is round.

Replace the inner hook.

of the

To the next page

2-C) Position of the shuttle is wrong.

Properly adjust the position od the shuttle.

2-D) Needle thread tension is too low.

Properly adjust the needle thread tension.

To the next page

Trouble

Cause (1)
From the previous page

Cause (2)

Check and corrective measures

From the previous page

2-E) Thread take-up spring tension

is too low.

Adjust the thread take-up spring.

2-F) Length of the remaining

needle thread is too long.

Properly adjust the tension controller No. 1.

2-G)The specified inner hook and

shuttle driver are not used.

Use the specified parts.

215

4-3) Scratches on the shuttle driver.

Remove the scratches and polish with buff, or replace

the shuttle driver.

4-4) Clearance between the shuttle

driver and the inner hook is too small.

Properly adjust the clearance between the shuttle

driver and the inner hook.

4-5) Scratches on the needle hole

guide.

Remove the scratches and polish with buff, or replace

the needle hole guide.

4-6) Finish of the needle hole is rough.

Replace the needle.

4-7) Thread take-up spring is

maladjusted.

4-8) Rotation of the inner hook is

defective.

4-9) Needle thread clamp device

OFF
4-10) Chemical fiber thread is
melted with heat from the
needle.

7-A) Stroke of the thread take-up

spring is too large.

Properly adjust the thread take-up spring.

7-B) Thread take-up spring tension

is too high.

Properly adjust the thread take-up spring.

8-A) Race face of the shuttle is

clogged with thread waste.

Remove the inner hook and remove the thread waste.

8-B) Oil amount is insufficient.

Supply oil to the shuttle components.

9-A) Needle thread length is

inadequate.

Adjust the needle thread length and turn the needle

thread clamp device ON.
Use of silicone oil
Use of needle coated with fluoro carbon resin

Trouble
5. Thread breakage at the time of
thread trimming.

Cause (1)
5-1) Thread release timing is
defective.

Cause (2)
1-A) Floating of the AT thread tension
disk is insufficient.

Check and corrective measures

Adjust the amount of AT thread tension floating.

5-2) Thread spreading section of the

moving knife has scratches.

Paying attention to the blade section, polish with

polishing powder.

5-3) Shuttle upper spring has

scratches.

Remove the scratches.

5-4) Level difference between the

needle hole guide and the
counter knife is too high.

4-A) Thread is cut before trimming

with the blade section of the
moving knife.

Properly adjust the position of counter knife.

5-5) Clearance between the needle

hole guide and the counter
knife is too small.

5-A) Thread is cut before trimming

with the blade section of the
moving knife.

Properly adjust the position of counter knife.

5-6) Lower face of the needle hole

guide has scratches.

6-A) Thread is cut with the needle

hole guide.

Remove the scratches and polish with buff, or replace

the needle hole guide.

216

5-7) Thread spreading timing of

the moving knife is defective.

Adjust initial positions of the presser origin sensor,

thread trimmer, and the moving knife.

5-8) Thread take-up spring tension

is too low.

Adjust the thread take-up spring.

5-9) Scratched bobbin thread

holder

Eliminate the scratch.

Trouble
6. Defective thread trimming

Cause (1)
6-1) Sharpness of the knife is
difective

6-2) Double cutting for the needle

thread. (Thread waste remains
inside the cylinder arm cap.)

Cause (2)

Check and corrective measures

1-A) Abrasion of moving and

counter knives.

Replace the moving and counter knives.

1-B) Engagement of the moving

and counter knives is defective.

Properly adjust the heigh and position of the moving

and counter knives.

1-C) Parallel of the blade section

of counter knife is defective.

Properly adjust the parallel of the blade section of

counter knife.

1-D) Attaching position of the

counter knife is defective.

Properly adjust the attaching position of counter knife.

2-A) There is a burr on thread spreading

section A of the moving knife.
The shape of the thread
trimmed becomes
and
thread waste remains.

Paying attention to the blade section, polish with

polishing power, or replace the moving knife.

217
6-3) Moving knife does not spread
threads.

6-4) Stitch skipping at the final stitch

6-5) Bobbin thread cannot be cut.

2-B) Shuttle upper spring has scratches.

(The shape of the thread trimmed
becomes
and thread waste
remains.)

Remove the scratches.

3-A) Initial position of the moving

knife is maladjusted.

Adjust the initial position of the moving knife.

3-B) Thread trimmer cam position

is inadequate.

Adjust the thread trimmer cam position.

3-C) Position of the shuttle upper

spring is defective.

Adjust the position of shuttle upper spring .

4-A) Timing of the needle to the

inner hook and the clearance
between them are defective.

Adjust the timing and the clearance.

4-B) Work clamp foot big.

Let the biginning of stitch come closer to the presser

by moving the pattern.

4-C) Loop of the needle thread

falls down.

Attach the needle with the long groove orienting

slightly to the right (approximately 20)

5-A) Bobbin thread tension is low.

Streng then the bobbin thread tension.

5-B) Needle hole size of the needle

hole guide is large.

Replace the needle hole guide with a new one having

a smaller hole diameter.

Trouble
7. Poorly tense stitches

Cause (1)
7-1) Tension controller AT is
maladjusted.

Cause (2)
1-A) Tension of the tension controller
AT is low.

Check and corrective measures

Properly adjust the tension of tension controller AT.

7-2) Tension controller AT is

floating.

Adjust the thread tension releasing mechanism.

7-3) Thread take-up spring is

maladjusted.

Adjust thread take-up spring tension and stroke.

218

7-4) Clearance between the inner

hook and the shuttle driver is
defective.

4-A) The clearance between the

inner hook and the shuttle
driver is too small.

Properly adjust the clearance of inner hook and

shuttle driver.

7-5) Selection of the needle to be

used is improper.

5-A) Needle to be used is thin.

Replace the needle with a thicker one.

7-6) Selection of the needle hole

guide is improper.

6-A) Hole diameter of the needle

hole guide to the needle to be
used and thread is small.

Replace the needle hole guide with a new one having

a larger needle hole.

7-7) Shape of the feed plate is

defective.

7-A) Material to be sewn is stiff and

closely contacted with the throat
plate, and there is no clearance
between them to pass the thread.

Raise the material to be sewn by means of the feed

plate.

7-B) Material to be sewn is highly

elastic and closely contacted
with the throat plate, and there
is no clearance between
them to pass the thread.

Raise the material to be sewn by means of the feed

plate.

8-A) Feed timing is too fast.

Use the memory switch to change the feed timing.

7-8) Feed timing is defective

Trouble
8. Defective stitches with the synthetic
thread

Cause (1)
8-1) Thread breakage due to heat

Cause (2)

Check and corrective measures

1-A) The sewing speed is too fast.

Slow down the maximum speed.

1-B) The needle used is too thick.

Use a thin needle or a super needle for the synthetic

thread.
Use silicon.
Use a needle cooler.

8-2) Thread makes burrs.

8-3) Thread floating occurs at the

sewing start.
8-4) Stitch skipping due to the heat.

219
8-5) Uneven stitch tightness due
to the stretch of thread.

9. Thread chips generated in the

shuttle

9-1) Long needle thread at the

beginning of stitches

2-A) Thread path is defective.

Polish the thread path of each component with polishing powder.

2-B) Finish of the needle hole is defective.

Replace the needle.

2-C) Loop of the needle thread falls down.

Move the machine arm thread guide A to the left.

3-A) Penetration registance of the

thread against the cloth is too
small.

Use a thinner needle. (Lower the number of needle to be used.)

Needle thread clamp device ON.

4-A) Sewing speed is too fast.

Change the maximum speed (electrical components.)

4-B) Needle is too thin.

Use a thicker needle. (Raise the number of needle to be used.)

4-C) Loop of the needle thread falls down.

Attach the needle with the long groove orienting slightly

to the right (approximately 20).

5-A) Sewing speed is too fast.

Reduce the speed by means of the speed variable resistor.

5-B) Tension of the tension controller

AT is excessive.

Decrease the tension of tension controller AT.

1-A) The thread trimmer is used

for cutting.

Needle thread clamp device OFF

Adjust the needle thread length to 32 ~ 36mm
Increase the sewing length to more than 10mm.

(3) Electrical components (Refer to 13.-(1) Block diagram A as well.)

Trouble
1. No display at the operation panel.

Cause (1)
1-1) DC power (+5 V, +24V) is not
supplied.

Cause (2)

Check and corrective measures

1-A) AC power is not supplied.

Examine if a power supply is available at the power

switch.

1-B) The FLT board has no power

supply.

Check whether an AC voltage is available between

Pins 4-5 of CN1 in the FLT board. If no voltage is found,
check the connections around the power switch or the
power plug.

1-C) The SDC board has no power

supply. (The power supply is
is available so long as LED4
of the SDC board is lit.)

Check the connection of CN1 of SDC board.

Check the connection between CN17 of the SDC board
and CN2 of the FLT board.
Confirm that the inrush protection resistor is normal in
the FLT board.
FLT-T board R2, R3
FLT-S board R1

220

1-D) The MAIN board has no power

supply.

Check the CN31 power supply of the MAIN board.

1, 2: +48V
3: +24V
4: +5V
5: +33V
6, 7, 8: GND
Check the output voltage in the SDC board unit.
Check if there is shortcircuiting in the 5V power
system for the MAIN board.

1-E) The operation panel has no

power supply.

Check if there is shortcircuiting in the +5V power

system for the operation panel.
Check the connection between CN34 of the MAIN
board and the panel.

1-2) Detection of a momentary

interruption in the SDC board
LED3 on SDC board:
Flashing 9 times

2-A) No momentary interruption

sensor signal input is entered
in the SDC board.

Check the connection between CN3 of the FLT board

and CN13 of the SDC board.

2-B) No AC voltage is available

between Pins 4-5 of CN1 in
the FLT board. (In case of
FLT-T board)

When a sewing machine for 3-phase specifications

is used in a 1-phase system, connect the power
supply to black and white of the power cord led from
the box.

Trouble
2. Key malfunction on the operation
panel
It does not function so effectively.

3. Error E007
Machine lock
LED3 on SDC board: Flashing 1 times

221

4. Error E029
Smart media slot open error

Cause (1)

Cause (2)

2-1) IP-400 : There is no signal

from the touch panel.

1-A) Connector connection defective

Check the connection between the touch panel and

CN109 of the Panel board.

1-B) The switch position of the

touch panel is displaced.

Start the Check Program 1_01 and readjust the switch

position.

1-C) Touch panel fault

Replacement of the LCD assembly (40034529)

2-2) CP-20: The Panel CPU does

not accept the key.

2-A) The circuit is out of order.

Replace the PANEL board (40031471).

3-1) The main shaft motor of the

sewing machine cannot rotate.

1-A) No power is fed to the motor.

Check the connection of CN16 of SDC board.

1-B) The mechanism is locked.

Turn it by hand in the state that the power supply

is turned OFF. Confirm whether the upper shaft is
locked. If there is any abnormality, remove it.

1-C) The driver circuit is out of order.

Replace the SDC board.

1-D) The motor is out of order.

Measure the resistance of the motor winding. If there

is any abnormality, replace the motor.

1-A) The slot OPEN-OFF switch

is not pressed.

Check the cover to examine whether the switch pin

can be pressed.
If there is any abnormality, replace the cover.

4-1) The switch signal is not received.

Check and corrective measures

Confirm the switch pin whether it is normal.

If there is any abnormality, replace the board.
5. Error E030
Needle bar upper position
displacement

5-1) It cannot stop in upper position.

1-A) The servo lock is not effective.

Turn it by hand in the state that the power supply is

turned OFF. Confirm if there are large variations in
the load.
Replace the SDC board.

6. Error E031
Air pressure drop

6-1) The air sensor switch is not

turned ON.

1-A) Air pressure variation or drop

Check the air pressure and the air source.

Check the pressure setup value of the air sensor
(0.34MPa)

1-B) Switch defective

Check the air switch by means of a circuit tester.

Connector check MAIN board CN52

Trouble
7. Error E050
Temporary stop switch

Cause (1)

Cause (2)

7-1) The switch contact point is

open.

1-A) Connector connection defective

Check CN69 of INT board.

1-B) Switch defective or disconnection

Confirm the condition of the switch by using the tester.

(Normal closure)

Check and corrective measures

222

8. Error E220
Grease up alarm

8-1) The number of stitches saved

in the INT board has exceeded
100 million stitches.

1-A) 100 million stitches have

been exceeded.

After grease supplement, clear the memory with the

memory switch U245.

9. Error E221
Grease up error

9-1) The number of stitches saved

in the INT board has exceeded
120 million stitches.

1-A) 120 million stitches have

been exceeded.

After grease supplement, clear the memory with the

memory switch U245.

10. Error E302

Head tilt error

10-1)Detector switch contact open

1-A) Connector contact is defective.

Check CN67 of INT board.

1-B) Disconnection

Check it by means of a circuit tester.

Replace the switch.

1-C) Switch is defective.

Check it by means of a circuit tester.

Replace the switch.

1-D) Switch fails to properly work.

Check the switch mounting conditions.

1-A) The encoder cord is broken

or the motor encoder circuit
is out of order.

Confirm whether each signal is delivered to CN14

of the SDC board.
CN14_9: Phase Z
CN14_2: GND
Replace the motor if there is no signal change as a
result of manual turning.

1-B) The detector circuit is out of

order.

Replace the SDC board.

1-A) The cam phase of the mechanical

block is not in good order.

Check the operation with the check program I_07.

1-B) The driver circuit is out of order.

Replace the MAIN board.

1-C) Motor defective

Measure the resistance of the motor winding by means

of a circuit tester.

2-A) Sensor defective/Mounting

inadequate

Check the sensor with the check program I_03.

2-B) Disconnection of connector

Check CN66 of INT board.

11. Error E303

Upper shaft motor Phase Z
sensor error
LED3 on SDC board:
Flashing 2 times

12. Error E305

Thread trimmer knife position
error

11-1)Phase Z signal (upper shaft

motor) is not received.

12-1)Presser lifter/thread trimmer

pulse motor fails to properly
work.

12-2)The sensor is not turned

ON.

Trouble
13.Error E306
Needle thread clamp position error

Cause (1)
13-1)Needle thread clamp pulse
motor fails to properly work.

13-2)The sensor is not turned ON.

14. Error E730

Main shaft motor encoder error A
LED3 on SDC board: Flashing
3 times

14-1)Main shaft motor: No signal

entry in Phase A and Phase B.

223
15. Error E731
Main shaft motor encoder error B
LED3 on SDC board: Flashing
4 times

15-1)Main shaft motor: No signal

entry in Phase U, Phase V,
and Phase W.

16. Error E733

Main shaft motor reverse turn
error
LED3 on SDC board: Flashing
7 times

16-1)The main shaft motor is

reversing.

17. Error E811

Overvoltage error
LED3 on SDC board: Flashing
8 times

17-1)Power source voltage is

beyond 280 V AC.

Cause (2)

Check and corrective measures

1-A) There is a certain obstacle in

the mechanical block.

Check the mechanical block to see if there is any

position with a heavy load or any section caught
by something.

1-B) The driver circuit is out of order.

Replace the MAIN board.

1-C) Motor defective

Measure the resistance of the motor winding by means

of a circuit tester.

2-A) Sensor defective

Check the sensor with the check program I_03.

2-B) Disconnection of connector

Check CN66 of INT board.

2-C) Sensor mounting inadequate

Check the operation with the check program I_08.

1-A) The motor is out of order.

Confirm whether each signal is delivered to CN14 of

the SDC board.
CN14_6: Phase A
CN14_7: Phase B
CN14_2: GND
Replace the motor if there is no signal change as a
result of manual turning.

1-B) The signal input circuit is out

of order.

Replace the SDC board.

1-A) The motor is out of order.

Confirm whether each signal is delivered to CN14 of

the SDC board.
CN14_3: Phase U
CN14_4: Phase V
CN14_5: Phase W
CN14_2: GND
Replace the motor if there is no signal change as a
result of manual turning.

1-B) The signal input circuit is out

of order.

Replace the SDC board.

1-A) Motor revolutions are unstable.

Check whether coupling for connection of main shaft

and motor is loose.
Replace the motor.

1-A) There are variations or unusual

rise in the AC input power line.

Check the AC input power line.

Trouble

Cause (1)

Cause (2)

18.Error E813
Low voltage error
LED3 on SDC board: Flashing
6 times

18-1)The source voltage is 160V

AC or below.

1-A) There are variations or unusual

drop in the AC input power line.

Check the AC input power line.

1-B) A 100V input is entered where

the FLT-T board has been set
for 200V.

Check the preset voltage for the FLT-T board.

19.Error E901
IPM Error
LED3 on SDC board: Flashing
5 times

19-1)Error output generation from

IPM in the SDC board

1-A) IPM control voltage drop

Replace the SDC board.

1-B) IPM overcurrent is detected.

Replace the SDC board.

Check and corrective measures

Replace the main shaft motor.

20.Error E903
Pulse motor power source error
LED3 on SDC board: Flashing
11 times

224

21.Error E904
Abnormal solenoid power
LED3 on SDC board: Flashing
12 times

22.Error E905
Thermal error in SDC board
LED3 on SDC board: Flashing
13 times

20-1)No +48V power output of

the SDC board available

1-A) Blown-out of the F1 fuse of

the SDC board.

Check if there is shortcircuiting in the +48V power

system for the MAIN board.
Replace the MAIN board.

1-B) Blown-out of the F4 fuse of

the SDC board.

Replace the SDC board.

1-A) Blown-out of the F2 fuse of

the SDC board.

Check if there is shortcircuiting in the +33V power

system for the MAIN board.
Replace the MAIN board.

1-B) Blown-out of the F5 fuse of

the SDC board.

Replace the SDC board.

22-1)Heat sink temperature for

power supply has exceeded
85C.

1-A) Cooling is not effective.

Check for any clogging at the suction port or examine

the conditions in the fan, etc.

22-2)Temperature of main shaft

IPM has exceeded 90C.

2-A) Cooling is not effective.

Check for any clogging at the suction port or examine

the conditions in the fan, etc.

2-B) Sensor connection defective

Check CN18 of SDC board.

2-C) The main shaft motor is out

of order.

Measure the resistance of the upper shaft motor winding.

Replace the motor.

21-1)No +33V power output of

the SDC board available

Trouble
23. Error E907
X feed motor origin retrieval error

Cause (1)
23-1)Irregular motor rotations

23-2)No sensor signal entry

24. Error E908

Y feed motor origin retrieval error

24-1)Irregular motor rotations

225
24-2)No sensor signal entry

25. Error E910

Presser motor origin retrival error

25-1)Irregular motor rotations

25-2)No sensor signal entry

Cause (2)

Check and corrective measures

1-A) There are irregularities in the

mechanism, such as
overloading, etc.

Check the mechanism and look for the section that

is particularly overloaded, that is any holdup or
whether screws are loose.

1-B) Motor leads are broken.

The motor is out of order.

Check the resistance of the motor winding.

Replace the motor, as required.

1-C) The driver circuit is out of order.

Replace the MAIN board.

2-A) The sensor is out of order or

broken.

Check the sensor with the test program I_03 or I_06.

2-B) Connector connection defective

Check CN62 of INT board.

2-C) Input circuit is out of order.

Replace the MAIN board.

1-A) There are irregularities in the

mechanism, such as
overloading, etc.

Check the mechanism and look for the section that

is particularly overloaded, that is any holdup or
whether screws are loose.

1-B) Motor leads are broken.

The motor is out of order.

Check the resistance of the motor winding.

Replace the motor, as required.

1-C) The driver circuit is out of order.

Replace the MAIN board.

2-A) The sensor is out of order or

broken.

Check the sensor with the test program I_03 or I_06.

2-B) Connector connection defective

Check CN63 of INT board.

2-C) Input circuit is out of order.

Replace the MAIN board.

1-A) There are irregularities in the

mechanism, such as
overloading, etc.

Check the mechanism and look for the section that

is particularly overloaded, that is any holdup or
whether screws are loose.

1-B) Motor leads are broken.

The motor is out of order.

Check the resistance of the motor winding.

Replace the motor, as required.

1-C) The driver circuit is out of order.

Replace the MAIN board.

2-A) The sensor is out of order or

broken.

Test program I_03 or I_07

2-B) Connector connection defective

Check CN64 of INT board.

2-C) Input circuit is out of order.

Replace the MAIN board.

Trouble
26. Error E913
Needle thread clamp origin
retrieval error

Cause (1)
26-1)Irregular motor rotations

26-2)No sensor signal entry

Cause (2)

Check and corrective measures

1-A) There are irregularities in the

mechanism, such as
overloading, etc.

Check the mechanism and look for the section that

is particularly overloaded, that is any holdup or
whether screws are loose.

1-B) Motor leads are broken.

The motor is out of order.

Check the resistance of the motor winding.

Replace the motor, as required.

1-C) The driver circuit is out of order.

Replace the MAIN board.

2-A) The sensor is out of order or

broken.

Check the sensor with the test program I_03 or I_08.

2-B) Connector connection defective

Check CN65 of INT board.

2-C) Input circuit is out of order.

Replace the MAIN board.

226

27. Error E914

Feed trouble error

27-1)Irregular main shaft motor

rotations

1-A) Motor revolutions are unstable.

Check whether coupling for connection of main shaft

and motor is loose.

28. Error E915

Communication error between
the PANEL and MAIN boards LED1
on MAIN board: Flashing 1 times

28-1)Data cannot be received

from the MAIN board.

1-A) MAIN board fails to work.

All the dip switches of the MAIN board shall be set

at OFF.

1-B) Board defective

Replace the MAIN board or PANEL board.

29. Error E916

Communication error between
the SDC and MAIN boards
LED3 on SDC board: Flashing
15 times

29-1)Data cannot be received

from the SDC board.

1-A) MAIN board fails to work.

All the dip switches of the MAIN board shall be set

at OFF.

1-B) SDC board fails to work.

All the dip switches (SW2) of the SDC board shall be

be set at OFF.

1-C) Board defective

Replace the MAIN board or SDC board.

1-A) Cooling is not effective.

Check for any clogging at the suction port or

examine the conditions in the fan, etc.

30. Error E918

MAIN board overheat

30-1)The heat sink for the power

supply has exceeded 85C.

Trouble
31. Error E925
Intermediate presser motor origin
retrival error

Cause (1)
31-1) Irregular motor rotations

31-2) No sensor signal entry

Cause (2)

Check and corrective measures

1-A) There are irregularities in the

mechanism, such as
verloading, etc.

Check the mechanism and look for the section that

is particularly overloaded, that is any holdup or
whether screws are loose.

1-B) Motor leads are broken.

The motor is out of order.

Check the resistance of the motor winding.

Replace the motor, as required.

1-C) The driver circuit is out of order.

Replace the MAIN board.

2-A) The sensor is out of order or

broken.

Check the sensor with the test program I_03 or I_10.

2-B) Connector connection defective

Check CN70 of INT board.

2-C) Input circuit is out of order.

Replace the MAIN board.

227

32. Error E943

MAIN board EEP-ROM write-in
trouble

32-1) MAIN board EEP-ROM

failingin writing

1-A) Devices defective, soldering

inadequate

Replace the MAIN board.

33. Error E946

INT board EER-ROM write-in
trouble

33-1) INT board EEP-ROM failing

in writing

1-A) Poor connections

Check the CN38 connections of the MAIN board.

1-B) Defective board

Replace the MAIN board and the INT board.

34. Error E948

MAIN board F-ROM write-in
trouble

34-1) MAIN board F-ROM failing

in writing

1-A) Devices defective, soldering

inadequate

Replace the MAIN board.

14. Circuit diagrams

(1) Block diagram A

MAIN PCB
40031449
CN88

40033831

2 pedal
PK78

CN88

10P

2P

40031465

2P

3 pedal
PK47

10P

2P

10P

2P
GPK470010AB

CN88
40033875

2P

40029628

CN72 (Blue)

CN51 (White)
Switch input x 5
10P PRESSER 1
PRESSER 2
PRESSER 3
PRESSER 4
Start

INSIDE PRESSURE MOTOR

4P

INTERMEDIATE
PRESSER 2 PHASE

40032539

CN39 (Yellow)
AT
max 1A

AT SOLENOID

2P
40029626

CN71 (Red)
6P
40032506

CN81

X FEED ORIGIN SENSOR

HD00057000A

3P

CN48
For PLD
(Red)

X-AXIS 5 PHASE

3P
CN83

Y-AXIS 5 PHASE

NEEDLE THREAD CLAMP

ORIGIN SENSOR

CN63
(Yellow)

CN61 20P

20P

3P

6P
40032508

CN64
(Black)

INT PCB
40032512

CN65
(Yellow)

NEEDLE THREAD CLAMP

POSITION SENSOR
40032509

CN85

THREAD TRIMMER
POSITION SENSOR
HD002230000

4P

CN66
(Red)

40029633

SAFETY SWITCH

2P

CN67
(Red)
8P

INTERMEDIATE PRESSER
ORIGIN SENSOR

CN82

3P

40029632
2P

TEMPORARY STOP

CN70
(White)

THREAD BREAKAGE
DETECTION

HA004250000
POWER
POWER
SWITCH
M90355800A0: 1/100W
M90175800A0: 3200V/220V
40005390: 1JE
M90245800A0: 1 ORDINARY EXPORT

CN81 (Red)
Switch
Input x 4

40032511
2P

CN69
(Black)

CN31 (White)
8P

CN71
(Yellow)

CN68
(White)

40005391: 3/1
40005392: JE
40005388: ORDINARY
EXPORT

40029629
PRESSURE FOOT MOTOR

40029630
THREAD HOLD MOTOR
40030778
WIPER Mg
Only Air style
CN98
40033965

CN52 (White)
2P
Air SW

CN1

10P

10P

4P

4P

CN78

FEDDING FRAME RIGHT

CN2 2P SOLENOID VALVE
2P FEDDING FRAME LEFT
40033964
SOLENOID VALVE

40030951

AIR SW

CN83 (Black)
air x5
11P
max0.5A

CN82 (Red)
12P Sensor
Input x 4

2P

Y FEED MOTOR

CN38

40032510

HD00057000A

5P

CN74 (White)
FEEDING FRAME/ 4P
THREAD TRIMMER
CN40 (White) 2 PHASE
4P For Analog pedal
CN75 (White)
6P
NEEDLE THREAD
CN79 (Red)
CLAMP 4 PHASE
Switch
10P Input x 5
CN47 (White)
MAG
2P
max10A
100ms
CN80 (Red)
CN84 (Black)
Sensor
9P
air x5
Input x 3
max0.5A 10P

40032507

LIFTING THE WORK CLAMP

FOOT ORIGIN SENSOR
HD00057000A

40029627

CN73 (White)

CN62
(Red)

40032505
Y FEED ORIGIN SENSOR

X FEED MOTOR

5P

SMART MEDIA

CN78 (Black)
air x6
12P
max0.5A

40031006

CN32
26P CN100

CN34 26P

40P

OPERATION PANEL
IP-400: 40030923
CP-20: 40032704

40005727

40005726

14P

4P

CN11

CN15

40005393
40012038: JE
CN2
6P

3P

3P

CN14

CN17

CN1

9P

SDC PCB: 40038663

40005394
CN3

5P

5P

MAIN SHAFT SERVO MOTOR ENCODER

F1 = 15AT
F2 = 3.15AT
F3 = 2A

CN13

FG1

CN16

4P

CN10
POWER WIRE OF THE MAIN SHAFT SERVO-MOTOR

FLT PCB
FLT-T: 40000056: 3/1
FLT-S: 40000046: 1

2P
FAN

228

40005401

MAIN SHAFT MOTOR

40003470

(2) Power supply circuit diagram A

FLT-T BOARD
200V CONNECTIONS

POWER SWITCH

SDC BOARD

MAIN BOARD
White
White

Green

Green

Black

Black

Yellow

White

White

Red

Red

Red

Orange
Black
Black
Black

Red
White
Black

Brown

White
Yellow

229

(3) Power supply circuit diagram B

FLT-T BOARD
100V CONNECTIONS

POWER SWITCH

SDC BOARD

MAIN BOARD
White

Green/
Yellow

Green

Gray

Black

Yellow

Gray

White

Red

Red

Orange

White

Black
Black
Black

Red
White
Black

Brown

White
Yellow

230

(4) Power supply circuit diagram C

FLT-S BOARD

SDC BOARD

POWER SWITCH

MAIN BOARD
White

Green/
Yellow

Green/Yellow

Brown

Brown

Yellow

Light Blue

Light Blue

Red

White

Orange
Black
Black
Black
Red
White
Black

Brown

White
Yellow

231

(5) Servo motor circuit diagram

AC SERVO MOTOR

SDC BOARD
White (Drain line)
Black
Orange
Blue
Purple

ENCODER

Light Blue
Pink
Red
Yellow

Black
Red
White
Green + Yellow

232

(6) Sensor-pedal circuit diagram

Red
X feed origin sensor

(Red)

White
Black
Brown

Y feed origin sensor

MAIN BOARD

(Yellow)

Black

(White)

Blue

Red
Lifting the work clamp
foot origin sensor

White
Black

Brown
Needle thread clamp
origin sensor

(Black)

(Yellow)

Black
Blue
Brown
Black
Blue

Needle thread clamp

position sensor

Red
Thread trimmer position
sensor

(Red)

White
Black

(Red)
Black
Safety switch

White

Red
Intermediate presser
origin sensor

(White)

INT BOARD

White
Black

TEMPORARY STOP

White

(Black)

Black

Thread breakage
detection

Black

(White)

233

(7) MAINPANEL board circuit diagram

MAIN BOARD

PANEL BOARD

234

(8) Motorsolenoid circuit diagram

(Red)
Red
Orange

Blue

White
AT solenoid

X feed motor

Yellow

(Yellow)

Black

Black
(White)
Red
(White)

Orange

Black

Y feed motor

Yellow
Blue

Wiper solenoid

White

Black

(White)
Orange
Blue

Thread trimmer lifting the work clamp foot motor

Red
Yellow

MAIN BOARD

(Blue)
Orange
Blue

Intermediate presser motor

Red
Yellow

(White)
Yellow
Red
Blue
Orange
White
Black

235

Needle thread clamp motor

(9) Air system circuit diagram

FU-05 (Option)

FU-05 (Option)
I
F

Feeding frame cylinder (left)

Hose elbow

Feeding frame cylinder (right)

Hose nipple

Inverting cylinder

Elbow union

Speed controller

T type tee

Solenoid valve

Plug

4 Air tube

Barrel nipple

Manifold

Filter regulator

Regulator

One-touch joint plug

One-touch joint socket

Air cock

6 Air tube

2-B

2-A

1-A

1-B

CN1

CN2
G

L
G

K
J

Pneumatic source

236

15. Drawing of the table

Z-Z (2pcs.)
Control box mounting hole

40

More than 40

ell p
(a ry)
R2 he
rip

Leg mounting hole

(Rear side: 2 positions, drill
depth 10)

Draw stopper mounting position

(1 position on rear side)

9 drill, 20 depth Counterbore

depth 17
4 x 8 drill

Top of table

17 drill

30 drill, 51 depth Counterbore

depth 16

PART No. : 40030949

237

l
al

h
rip

pe

er

y)

The environmental management system to promote and conduct

the technological and technical research, the development and
design of the products in which the environmental impact is considered,
the conservation of the energy and resources, and the recycling, in
the research, development, design, distribution, sale and maintenance service of the industrial sewing machines, household sewing machines and industrial-use robots, etc. and in the sale and
maintenance service of data entry system and in the purchase, distribution and sale of the household commodities including the
healthcare products.

2
This manual uses environment-friendly soyink.

MARKETING & SALES H.Q.

8-2-1, KOKURYO-CHO,
CHOFU-SHI, TOKYO 182-8655, JAPAN
PHONE : (81)3-3480-2357 2358
FAX : (81)3-3430-4909 4914

Copyright 2006 JUKI CORPORATION.

All rights reserved throughout the world.

Please do not hesitate to contact our distributors or agents in your area for further information when necessary.
* The description covered in this engineer's manual is subject to change for improvement of the
commodity without notice.
06 01 Printed in Japan (E)