Scribd
Upload
178 views

Eed3001 Lab2 Single Phase Transformer Loading EM3000

1) The objective of this experiment is to analyze the performance of a single-phase transformer under resistive, inductive, and capacitive loads by measuring input and output voltage, current, power, and calculating efficiency and regulation. 2) Students will connect a single-phase transformer to different load modules and record measurements using various meters. They will calculate secondary power, reactive power, efficiency and regulation to analyze transformer performance under different load conditions. 3) Students are required to plot graphs of secondary voltage and power versus current, and efficiency and regulation versus primary current to discuss the results and comment on the observations in their report.

Uploaded by

Burak Yılmaz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
178 views

Eed3001 Lab2 Single Phase Transformer Loading EM3000

1) The objective of this experiment is to analyze the performance of a single-phase transformer under resistive, inductive, and capacitive loads by measuring input and output voltage, current, power, and calculating efficiency and regulation. 2) Students will connect a single-phase transformer to different load modules and record measurements using various meters. They will calculate secondary power, reactive power, efficiency and regulation to analyze transformer performance under different load conditions. 3) Students are required to plot graphs of secondary voltage and power versus current, and efficiency and regulation versus primary current to discuss the results and comment on the observations in their report.

Uploaded by

Burak Yılmaz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

DOKUZ EYLUL UNIVERSITY

Faculty of Engineering
Electrical and Electronics Engineering

Dokuz Eyl
ul Universitesi,
M
uhendislik Fak
ultesi,

Elektrik-Elektronik M
uhendisli
gi, TR35160 Kaynaklar, Buca/Izmir.

T 0090/232/ 301-7155

EED3001 Energy Conversion Laboratory 2


Group #:

Objective(s):
The object of this experiment is to show how the input power, efficiency, output voltage, and regulation of a single phase transformer vary with resistive, inductive, and
capacitive loading conditions.
Equipment will be available at the laboratory:
Three-phase Power Supply Module
EM-3310-1B
Three-pole Current Limit Protection Switch Module EM-3310-2A
Resistive Load Module
EM-3310-4R
Inductive Load Module
EM-3310-4L
Capacitive Load Module
EM-3310-4C
Digital ACA Meter
EM-3310-3C
Digital ACV Meter
EM-3310-3D
Digital Power Analysis Meter
EM-3310-3H
Fuse Set
EM-3310-5B
Single-phase Transformer
EM-3340-1A
Connecting Leads Set
EM-3390-3A
Safety Bridging Plugs Set
EM-3390-4A
Equipment will be ensured by the students:
None
Procedure:
1. Install the required modules in the experimental frame. Construct the circuit in accordance with the circuit diagram in Figure (1) and the connection diagram in Figure
(2). The single-phase transformer is connected to a purely resistive load.
2. Sequentially turn on the 3-P current limit protection switch and three-phase power
supply modules
3. Record the rms voltage, current, real power, and power factor values from digital
ACA, ACV, and power analysis meters for each of switch positions of the resistive load
module in Table (1).
1

Figure 1: Circuit diagram of the experimental setup.


4. Sequentially turn off three-phase power supply and the 3-P current limit protection
switch modules.
5. Calculate the required values using the equations below and complete Table (1).
6. Using the results of Table (1), plot the secondary voltage V2 versus secondary current
curve I2 .
7. Using the results of Table (1), plot the secondary power P2 versus secondary current
curve I2 .
8. Repeat the procedure with inductive load and fill the Table (2),
9. Repeat the procedure with inductive load and fill the Table (3).
Question(s):
Explain the main features you have learned from the experiments. Additionally, plot
graphs of efficiency and regulation to the base of primary current. Discuss on the
graphics obtained from the tests and comment on the results in your report.
Supplementary Information: Calculate the power factor, secondary real/reactive power,

Figure 2: Circuit diagram of the experimental setup with resistive load bank.
3

SW
V1 [V]
All OFF
S1=ON
S1 to S2=ON
S1 to S3=ON
S1 to S4=ON
S1 to S5=ON
S1 to S6=ON

Measured values
I1 [A] P1 [W] V2 [V] I2 [A]

cos

Calculated Values
P2 [W] VR [%] [%]

Table 1: Measured and calculated values with resistive load


Legend: SW: Switch Positions, V1 : Primary Voltage, I1 : Primary Current, P1 : Primary
Real Power, V2 : Secondary Voltage, I2 : Secondary Current, cos : Input Power Factor, P2 :
Secondary Real Power, V R: Regulation, : Efficiency.

SW
V1 [V]
All OFF
S1=ON
S1 to S2=ON
S1 to S3=ON
S1 to S4=ON
S1 to S5=ON
S1 to S6=ON

Measured values
I1 [A] P1 [W] V2 [V] I2 [A]

cos

Calculated Values
Q2 [V.A.R.] VR [%] [%]

Table 2: Measured and calculated values with inductive load


Legend: SW: Switch Positions, V1 : Primary Voltage, I1 : Primary Current, P1 : Primary
Real Power, V2 : Secondary Voltage, I2 : Secondary Current, cos : Input Power Factor, Q2 :
Secondary Reactive Power, V R: Regulation, : Efficiency.

SW
V1 [V]
All OFF
S1=ON
S1 to S2=ON
S1 to S3=ON
S1 to S4=ON
S1 to S5=ON
S1 to S6=ON

Measured values
I1 [A] P1 [W] V2 [V] I2 [A]

Calculated Values
Q2 [V.A.R.] VR [%] [%]

cos

Table 3: Measured and calculated values with capacitive load


Legend: SW: Switch Positions, V1 : Primary Voltage, I1 : Primary Current, P1 : Primary
Real Power, V2 : Secondary Voltage, I2 : Secondary Current, cos : Input Power Factor, Q2 :
Secondary Reactive Power, V R: Regulation, : Efficiency.
voltage regulation, and efficiency using the following formulas:
cos =
P2 =
Q2 =
VR =
=

P1
V1 I1
V22
= V2 I2
R
V22
= V2 I2
X
V1 V20
100
V20
P2
100
P1

[1]

(1)

[W]

(2)

[V.A.R.]

(3)

[%]

(4)

[%]

(5)

Where V20 is the value of the secondary voltage referred to the primary side by the turns
ratio of the transformer under test.
End of the document.

You might also like