HYBRID OPERATING ROOM DESIGN GUIDE

FASTER SPEED TO MARKET AND FEWER CONSTRUCTION

HEADACHES WITH SEVEN PROVEN TECHNIQUES

Carondelet Heart and Vascular Institute

St. Marys Hospital
Tucson, AZ

Carondelet Heart and Vascular Institute

St. Marys Hospital
Tucson, AZ

One

reason

hybrid

operating

room

renovations are so challenging is the

number of consultants and vendors
involved.

Inside we discuss techniques we have found to be

effective in bringing a project to market quickly
with minimal headaches.

Choose design team leaders who take a hands-on

role in equipment coordination.
Establish a dual-track user group meeting schedule.
Develop a full scale mockup room.
Secure equipment vendor decisions from the clinical
team at the start of Design Development.
Consider the benefits of redundancy.
Facilitate interdisciplinary coordination by working in
Revit.

St. Peters Hospital - Albany, NY

CHOOSE DESIGN TEAM LEADERS WHO TAKE A HANDS-ON ROLE IN EQUIPMENT COORDINATION

Simply inserting equipment vendor drawings into the project construction documents often means the overlap
between vendors on ductwork, conduit runs, data, and other utilities isnt coordinated until construction is
underway. Sorting through these items during construction leads to schedule delays, change orders, and
additional costs.
To prevent this scenario, we recommend that Owners choose an A/E team leader who takes a hands-on role
in equipment coordination and has previous experience with hybrid OR projects. The owner benefits from
an architect who can translate clinical and functional needs into an appropriate technical solution. Architects
with a working knowledge of the interface between vendors, equipment, and design disciplines are able to
ask the right questions and include the right decision makers. While equipment, wiring, and data may not fall
within an architects scope per se, as the prime consultant on the project they serve as air traffic controllers
to direct the aspects of the project that fall between silos. This coordination ultimately affects the success or
failure of the job.
To illustrate, we are aware of a recent hybrid OR project where the design team did not provide proper
ventilation to the tall storage cabinet housing the computer integration system. The equipment generated an
excessive amount of heat which shorted out the IT system and rendered the OR unusable, costing thousands
in lost revenue. An architect with the ability to anticipate the potential repercussions of design choices would
have the team investigate ventilation and a designated supply diffuser to cool the equipment, avoiding
downtime and additional cost.

ESTABLISH A DUAL-TRACK USER GROUP MEETING

DEVELOP A FULL SCALE MOCKUP ROOM

SCHEDULE

During the design development phase of the

While some would assert that its better to have all

project, we bring clinical and technical user groups

parties participate in every meeting, we find that

together to vet the design in a full scale mockup

speed of delivery improves when there are separate

room. During the mockup session, we ask all team

clinical and technical meetings.

members to stand in position as they would when

performing surgery. We verify that everyone can

In the clinical meeting track, users determine the

see and access the pieces of equipment they need

layout of the room and its basic parameters and

for their roles. As some staff move around while

uses.

In the technical track, users discuss nuts

others remain stationary, we typically run through

and bolts items - such as which boom has which

the entire sequence of simulated procedures in order

gases - with the participation from one clinical team

to capture specific needs at different times.

representative.
To closely simulate the future space, we recommend
The advantage of having separate tracks is that users

using actual equipment where possible. Typically

focus on their areas of interest, without having to

the tables, perfusion equipment, and anesthesia

spend time on discussions that are not as relevant to

equipment are real, and the lights are real but

their roles. Streamlining user involvement improves

mounted on stands.

decision-maker participation at meetings, resulting

medical gas panels are mounted on a movable wall.

in more rapid decisions that ultimately expedite the

The control room is built from cardboard, and the

schedule.

tall storage cabinets are drawn on cardboard.

Actual electrical, data, and

SECURE EQUIPMENT VENDOR DECISIONS FROM THE CLINICAL TEAM AT THE START OF DESIGN DEVELOPMENT

We recommend that equipment vendor decisions be made at the start of the Design Development phase, prior
to the start of clinical user group meetings. This allows the design team to prepare a clear architectural response
for clinical team input and to schedule joint sessions between the selected equipment vendors and users.
Because equipment dimensions, clearances, and requirements vary depending upon the manufacturer, this
approach also assures that accurate measurements are used consistently throughout the design, minimizing
change orders and construction delays.

CONSIDER THE BENEFITS OF REDUNDANCY

On a recent project, the dedicated HVAC unit specified for the imaging equipment electronics was replaced
during construction. During the initial startup, the new system wasnt able to handle loads resulting from 100+
degree summer temperatures. As a result, the imaging system electronics shut down, delaying procedures and
causing tremendous issues for the facilities director.
Given the high value of the hybrid equipment and potential revenue loss from MEP system malfunctions,
hospitals should consider the cost benefit of redundant cooling and other infrastructure for the equipment
and hybrid OR room itself. While redundant infrastructure affects the budget, we can help facility managers
understand the many factors involved in a cost-benefit analysis.

Carondelet Heart and Vascular Institute

St. Marys Hospital
Tucson, AZ

DETERMINE THE IMPACT ON HOSPITAL-WIDE INFRASTRUCTURE DURING THE SCHEMATIC DESIGN PHASE

Hybrid ORs can overburden existing MEP systems.

the more backtracking is required and the greater

If the existing building infrastructure is not adequate

the impact on schedule and budget.

for the new equipment, reaching this conclusion

during the Schematic Design phase enables the team

We typically include the space above the ceiling in

to mitigate the impact of infrastructure adjustments

our assessment of existing infrastructure. Nine foot

to the schedule and budget.

ceiling heights as were commonly installed twenty

years ago will not accommodate new hybrid OR

In contrast, such a determination during Design

imaging equipment without sacrificing functionality.

Development

Documentation

On a recent project with 811 ceilings, we pushed

phases can result in both cost and schedule overruns.

the envelope and the low booms have proven to

As one example, perhaps the infrastructure simply

be head-knockers.

or

Construction

cannot be upgraded and the only solution is to start

over in another location, voiding all design efforts

The magnitude of new MEP infrastructure required

completed to date.

to update an older space can sometimes render an

ideal OR location significantly less so.

In those

Another scenario is that the space allows for an

instances, when the cost and difficulty of installing

MEP equipment upgrade, but new equipment

supplemental MEP equipment is cost prohibitive,

is expensive with long lead times. In both cases,

reconsidering the entire floor plan may be more

the longer it takes to reach the conclusion that the

achievable than the OR location with optimal

existing infrastructure capabilities are insufficient,

adjacencies.

Carondelet Heart and Vascular Institute

St. Marys Hospital
Tucson, AZ

UTILIZE BIM TO FACILITATE INTERDISCIPLINARY COORDINATION

Using Revit to develop documents greatly reduces

Equipment vendors often excel at 3-d modeling.

the potential for information leakage during hand-

Using Revit, they can incorporate final fabrication

offs between consultants and vendors. Through

details and convert the model into shop drawings,

the clash detection process, team members work

streamlining the documentation process and saving

together to resolve any remaining conflicts prior

significant amounts of time.

to construction, resolving issues that would have

traditionally been addressed in the field.

Revit

facilitates

above-ceiling

engineering

coordination, saving significant time in the overall

This synchronization effort begins during the A/E

design/construction schedule. By detailing the

design phase and continues through contactor

coordination between the conduit, support structure,

coordination, shop drawings, and construction.

mechanical, and lighting systems for the selected

Because

change

equipment, it is possible to expedite shop drawings,

everywhere, discrepancies and cost anomalies can

coordination, and ultimately the construction and

be addressed in real time, minimizing errors and

installation.

change

anywhere

is

creating better, more predictable project outcomes.

While no project seems to cruise through the construction phase, design teams and owners can
work together to make installations run more smoothly. In our experience, facilities directors feel
as though they are set up for success when our coordination efforts minimize change orders and
account for future conditions. The more the design team can do to lessen the potential that the
facility director must report a schedule delay or cost increase to administration, the better.

Healthcare providers currently face a dizzying array of strategic and facilities challenges. At FreemanWhite,
our approach integrates data, research, and best practices into our architectural solutions to help you balance
cost and value.

ABOUT THE AUTHORS

For Brian Adams, solving clients problems starts with the ability
to listen and to ask the right questions to deliver appropriate
solutions. Brian is deeply experienced in practical implementation,
recognizing that while each client is unique, all face an evolving
healthcare industry that requires providers to do more with less.
Brian Adams

AIA

As a proven leader of more than five complex surgery projects,

Principal
[email protected]
615.649.4691

Brian is constantly seeking innovations that enable clients to

lower costs while improving service.

Allen Smith is a natural problem-solver. His blend of experience

and expertise enables him to evaluate physical spaces;
conceptualize ideal heating and cooling systems; and create
appropriate designs. His creative approach has led him to
develop spreadsheets and other design tools to better analyze
Allen Smith

building systems such as air-handler psychrometrics and more

PE

Mechanical Engineer
[email protected]
704.586.2446

accurately design equipment. He has more than 15 years of

healthcare mechanical design experience including multiple OR
and Hybrid OR projects.

5300 MARYLAND WAY, SUITE 101

BRENTWOOD, TN 37027
615.649.4707
WWW.FREEMANWHITE.COM