Digiplex Quick Programming Guide DGP848 (V4.
00)
SECTION A: Product information
* Zone configuration
Model
DGP-848
On board zone
8 zones
Keypad zone
2 zones
Expander
Hardwire
APR3-ZX 4 Four (4) zone hardwire
APR3-ZX 8 Eight (8) zone hardwire
DGP2-50 Addressable PIR (Dual element)
DGP2-60 Addressable PIR (Quad element)
DGP2-70 Addressable Pet immunity PIR
Wireless
MG-RCV3 Magellan wireless receiver
MG-DCT1 Door transmitter
MG-PMD1P Pet immunity PIR (dual element)
MG-PMD75 Pet immunity PIR (Dual-Optic)
MG-PMD85 OUTDOOR Pet immunity PIR
Note: Any combination either hardwire or/and wireless
up to 48 zones
* System modules
DGP848
8 zones
Hardwire zone
APR3-ZX 4
APR3-ZX 8
4 zones
8 zones
Addressable zone
DGP2-50 Addressable PIR (Dual element)
DGP2-60 Addressable PIR (Quad element)
DGP2-70 Addressable Pet immunity PIR
1 zone
1 zone
1zone
Wireless zone
MG-RCV3 Magellan wireless receiver (up to 16 transmitters)
MG-DCT1 Door transmitter
MG-PMD1P Pet immunity PIR (dual element)
MG-PMD75 Pet immunity PIR (Dual-Optic)
MG-PMD85 OUTDOOR Pet immunity PIR
1 zone
1 zone
1 zone
1 zone
Keypad
DGP2-641 LCD (supply with panel)
DGP-648 LED 48 zones
Accessories
APR3-ADM2 In touch voice arm/disarm module
APR3-PRT1 Printer module
APR3-PGM1 One PGM expansion module
APR3-PGM4 Four PGM expansion module
DGP2-ACM1P Access control module
*System features
Features
8 zone on board, expandable to 48 zones (in any combination up to 95 number of modules)
4 partitions
96 user codes
1024 events log
Expandable to 125 PGM outputs
Access control up to 32 doors
4 wires bus for all modules supports up to 95 numbers of modules and connects modules up to 3000ft
(18AWG) / 1000ft (22AWG) from the panel.
2 on-board PGM expandable up to 125
1.1A for Aux. power
Supervise bell output
Telephone line monitoring
Hourly test transmission
Call up to 4 phones
Arm/disarm and control PGM via phone
Specifications
Maximum Aux power 700mA [DGP-641keypad is 60 mA per unit, APR3-ZX4 is 20 mA, APR3-ZX8 is 40mA,
addressable PIR is 16 mA]
Wire gauge refers to PAGE 42 of Original Programming Guide
SECTION B: Programming
To enter Programming Mode:
1.
2.
3.
4.
Press and hold the[0] key
Enter [000000], you are in the programming mode
Enter 3 digits SECTION number
Enter required DATA (Either enter 2 digits, 3 digits or ON / OFF relevant key)
Press [ENTER] to confirm or [CLEAR] to ignore
For value [0] to [9], choose key [0] to [9]. For value [A] is [STAY] key, value [B] is [FORCE] key,
value [C] is [ARM] key, value [D] is [DISARM] key, value [E] is [BYP] key & value [F] is [MEM] key.
Remember: After keyed in a required DATA, always press ENTER and CLEAR, in order to let the ENTER key
flashing before proceed with entering the next 3 digits SECTION number.
Example: The main board is 8 zones, one keypad zone, one 8 zone expander (ZX8) & 2 pcs
of PIR.
Note: All zones can be assigned to any desired zone number.
MUST do step 1 ,2 & 3, or else zone is DISABLE
Step 1 Zone Numbering
Press & hold [0], then enter [000000], you are in the programming mode
Main board:
Press section [001], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 001.
Press section [002], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 002.
Press section [003], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 003.
Press section [004], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 004.
Press section [005], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 005.
Press section [006], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 006.
Press section [007], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 007.
Press section [008], enter [8 digit S/N, then 3 digit input], means 8 digits is the main board s/n, and key in 008.
Keypad:
Press section [009], enter [8 digit S/N], means 8 digits is the keypad s/n, and key in 009.
8 zones Expander board:
Press section [010], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 001.
Press section [011], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 002.
Press section [012], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 003.
Press section [013], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 004.
Press section [014], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 005.
Press section [015], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 006.
Press section [016], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 007.
Press section [017], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 008.
PIR:
Press section [018], enter [8 digit S/N], means 8 digits is the PIR s/n.
Press section [019], enter [8 digit S/N], means 8 digits is the PIR s/n.
8 zones Expander board:
Press section [020], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 001.
Press section [021], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 002.
Press section [022], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 003.
Press section [023], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 004.
Press section [024], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 005.
Press section [025], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 006.
Press section [026], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 007.
Press section [027], enter [8 digit S/N, then 3 digit input], means 8 digits is the expander board s/n, and key in 008.
16 zones Wireless Receiver:
Press section [028], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 001.
Press section [029], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 002.
Press section [030], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 003.
Press section [031], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 004.
Press section [032], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 005.
Press section [033], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 006.
Press section [034], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 007.
Press section [035], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 008.
Press section [036], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 009.
Press section [037], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 010.
Press section [038], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 011.
Press section [039], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 012.
Press section [040], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 013.
Press section [041], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 014.
3
Press section [042], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 015.
Press section [043], enter [8 digit S/N, then 3 digit input], means 8 digits is the Receiver S/N, and key in 016.
Note: Transmitter S/N program in Step 7 D
Step 2 Zone Type , Partition & Options
Press & hold [0], then enter [000000], you are in the programming mode
Press section [101], [6,1, ENTER], means ZONE 1 Instant, Partition 1.
Press section [102], [6,1, ENTER], means ZONE 2 Instant, Partition 1.
Press section [103], [6,1, ENTER], means ZONE 3 Instant, Partition 1.
Press section [104], [6,1, ENTER], means ZONE 4 Instant, Partition 1.
Press section [105], [6,1, ENTER], means ZONE 5 Instant, Partition 1.
Press section [106], [6,1, ENTER], means ZONE 6 Instant, Partition 1.
Press section [107], [6,1, ENTER], means ZONE 7 Instant, Partition 1.
Press section [108], [6,1, ENTER], means ZONE 8 Instant, Partition 1.
Press section [109], [1,1, ENTER], means ZONE 9 Delay, Partition 1.
Press section [110], [6,1, ENTER], means ZONE 10 Instant, Partition 1.
Press section [111], [6,1, ENTER], means ZONE 11 Instant, Partition 1.
Press section [112], [6,1, ENTER], means ZONE 12 Instant, Partition 1.
Press section [113], [6,1, ENTER], means ZONE 13 Instant, Partition 1.
Press section [114], [6,1, ENTER], means ZONE 14 Instant, Partition 1.
Press section [115], [6,1, ENTER], means ZONE 15 Instant, Partition 1.
And [116] for zone 16, [117] for zone 17, and so on .
Key in section
101 for zone 1
102 for zone 2
103 for zone 3
up to .
148 for zone 48
Zone type
0 for zone disable
1 for entry delay 1
5 for follow
6 for Instant
8 for 24 hour [panic]
A for fire[24 hour]
Partition
1 for partition 1
2 for partition 2
3 for partition 3
4 for partition 4
Zone options
1 for auto zone shutdown [default: OFF]
2 for Bypassable zone [default: ON]
3 for stay zone [default: OFF]
4 for force zone [default: OFF]
5 & 6 are OFF for audible zone [default]
5 ON & 6 OFF for silent zone
7 for intellizone [default: OFF]
Note 1:
The 1st digit represents by: 1 for Delay zone, 5 for Follow zone, 6 for Instant zone, 8 for 24 hour alarm.
Dont program keypad zones if not used.
Note 2:
If the zone wants to become a STAY zone, instead of [6,1,ENTER, CLEAR], replace it with
[6,1 and ON key 3, ENTER, CLEAR], means this zone will be bypassed when stay armed.
If the zone want to become a FORCE zone, instead of [6,1,ENTER, CLEAR]. Replace it with
[6,1,and ON key 4, ENTER, CLEAR], means this zone will be allowed open during arming.
Note 3:
By default, all zones are Bypassable.
Step 3 Enable EOL (end of line resistor)
Press & hold [0], then enter [000000], you are in the programming mode
Press section [504], [ON key 7], means used of EOL resistor on hardwire zone
Step 4 - Others essential basic features to be programmed
Press & hold [0], then enter [000000], you are in the programming mode
Fast zone for zones
Section 201, enter [002] for 40 ms for vibration sensor on zone 1
Section 202, enter [002] for 40 ms for vibration sensor on zone 2
Section 203, enter [002] for 40 ms for vibration sensor on zone 3
Section 204, enter [002] for 40 ms for vibration sensor on zone 4
Section 205, enter [002] for 40 ms for vibration sensor on zone 5
Section 206, enter [002] for 40 ms for vibration sensor on zone 6
Section 207, enter [002] for 40 ms for vibration sensor on zone 7
Section 208, enter [002] for 40 ms for vibration sensor on zone 8
And section 209 for zone 9 and so on
Section 226 for exit delay partition 1 (e.g.: enter [226], then key in [030] for 30 seconds). Default is 60 seconds
Section 230 for entry delay partition 1 (e.g.: enter [230], then key in [030] for 30 seconds). Default is 30
seconds
Section 234 for bell timer partiton 1 (e.g.: enter [234], then key in [010] for 10 minutes). Default is 4 minutes
Section 506, key for keypad Panic option wanted. (e.g:[ ON 1,2,3,4,5,6][ENTER][CLEAR] for audible panic
[1]&[3], [4]&[6], [7]&[9] )
Section 508, ON key for option wanted. For one-touch functions. (e.g: ON 1 for regular arming, ON 2 for stay
arming, ON 3 for instant arming & ON 4 for force arming) Note: Stay & force arming need to be programmed
in Step 2 for each individual zone.
* Choose either Step 5A or 5B
Step 5 A To call Handphone / Phone
Press & hold [0], then enter [000000], you are in the programming mode
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Section 521, ON key [3], (key 4 5 & 6 remain ON). To enable Dialer.
Section 524, ON key [1,2,3 & 4], for alarm reporting to telephone 1,2,3 & 4. Note: for partition 1
Section 550, enter [7777] for pager reporting format to dial tel. 1,2,3 & 4.
Section 551, enter [8888]. For account no. 1
Section 552, enter [8888]. For account no. 2
Section 553, enter [8888]. For account no. 3
Section 554, enter [8888]. For account no. 4
Section 561, enter phone no. 1 follow with codes (e.g.: 0121234567 BYP 88 BYP 88 BYP 88 BYP 88 BYP 88
BYP 88 BYP 888).
Section 562, enter phone no. 2 follow with codes (e.g.: 0121234567 BYP 88 BYP 88 BYP 88 BYP 88 BYP 88
BYP 88 BYP 888).
Section 563, enter phone no. 3 follow with codes (e.g.: 0121234567 BYP 88 BYP 88 BYP 88 BYP 88 BYP 88
BYP 88 BYP 888).
Section 564, enter phone no. 4 follow with codes (e.g.: 0121234567 BYP 88 BYP 88 BYP 88 BYP 88 BYP 88
BYP 88 BYP 888).
Section 655, enter 33333333. For alarm reporting codes zone 1 to 4.
Section 656, enter 33333333. For alarm reporting codes zone 5 to 8.
Section 657, enter 33333333. For alarm reporting codes zone 9 to 12.
Section 658, enter 33333333. For alarm reporting codes zone 13 to 16.
Call sequence: Tel 1, 2,3 and 4 each ONE time only
Step 5B - Link to Centre Monitoring Station (CMS)
Press & hold [0], then enter [000000], you are in the programming mode
Section
550
521
522
551
561
562
261
270
790
Contact I.D
[55]
ON key [3], (key 4, 5 & 6 remain ON)
ON key [6], alternative dial
Enter 4 digit account no 1
(Note: account with digit [0 = STAY] key
Enter phone no. 1 (e.g.: 12345678 [ENTER][CLEAR] )
Enter phone no. 2 (e.g.: 12345679 [ENTER][CLEAR] )
Enter [001] for daily auto test
Enter [HH:MM] for test time
Press [ENTER], for all reporting codes from section 600 to 718.
600 to 718
Do nothing
Step 6 PGM 1 (Programmable output)
Press & hold [0], then enter [000000], you are in the programming mode
Option 1
Section 400, enter 11 & ON key 1
Section 401, enter 11 & ON key 1
Arming in regular mode
(including stay, force, instant & keyswitch arming)
Option 2
Section 400, enter 11 & ON key 5
Section 401, enter 11 & ON key 5
Strobe
Option 3
Section 400, enter 44 & ON key 2
Section 401, enter 44 & ON key 2
Section 400, enter 21 & ON key 1
Section 401, enter 21 & ON key 1
Fail to communication on tel. 1
Option 4
Ready status
For more options, refer to System Programming Outputs Guide.
Wiring connection: POSITIVE leg of LED to AUX + and NEGATIVE leg of LED (with 1k resistor) to PGM. Note:
PGM only support 50mA, a Relay is needed if more than 50mA.
Step 7: Modules Programming Guide For expansion modules
To enter Programming Mode (it is advisable to use LCD to do this programming):
1.
2.
3.
Press and hold the [0] key
Enter [000000] (SECTION will be displayed on LCD keypad), you are in the programming mode
Enter SECTION [953] (NOTE: this 953 is common section applicable for all the expansion modules)
Then, choose one of the following expansion modules serial numbers
4.
5.
6.
Enter 8-digit [Serial number] of the Expansion module
Enter 3-digit [SECTION] you wish to program
Enter required [DATA]
Press [ENTER] to confirm or [CLEAR] to ignore
A: LCD keypad (DGP2-641)
Section [003], ON key [2,3 & 8], to display exit delay, entry delay and time on keypad
B: 48 zone (DGP-648) LED keypads
C: Addressable PIR (DGP2-50 / DGP2 60 / DGP2 70)
Section [001], On key 1, for less sensitive
Section [002], enter [003], meaning 000 is for very sensitive, 002 normal and 003 less sensitive. (default is 002)
D: Omnia Wireless Receiver Module (OMN-RCV3)
Section [001], On key [1], for low battery supervision
st
Press section [101], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 1 input of the receiver)
nd
Press section [102], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 2 input of the receiver)
Press section [103], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 3rd input of the receiver)
th
Press section [104], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 4 input of the receiver)
Press section [105], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 5th input of the receiver)
th
Press section [106], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 6 input of the receiver)
th
Press section [107], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 7 input of the receiver)
th
Press section [108], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 8 input of the receiver)
Press section [109], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 9th input of the receiver)
th
Press section [110], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 10 input of the receiver)
Press section [111], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 11th input of the receiver)
th
Press section [112], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 12 input of the receiver)
th
Press section [113], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 13 input of the receiver)
th
Press section [114], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 14 input of the receiver)
Press section [115], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 15th input of the receiver)
th
Press section [116], enter [6 digit S/N], means 8 digits is the transmitter S/N. (becomes 16 input of the receiver)
For MG Remote Control
Assign Remote to follow panels user number
Press section [301], enter [3 digit user no.], for remote control 1.
Press section [302], enter [3 digit user no.], for remote control 2.
up to [316] for remote control 16.
Button assignment (for button A, B, C, D)
Press section [401], enter [1,5,7,7], for remote control 1.
Press section [402], enter [1,5,7,7], for remote control 2.
up to [416] for remote 16
For Button C activates (ON for 2 seconds) PGM on OMNIA RCV3 Receiver [for example to trigger autogate]
Press section [401], enter [1,5,0,7], for remote control 1s Button C to trigger PGM 3 on RCV3 for 2 seconds
Note:
Meaning Button A (TOP) assigned for Regular Arming, Button B (BOTTOM) assigned for Disarm and Button C
(LEFT) & D (RIGHT) are assign for Panic (same as keypad panic 1& MUST program in section [506][ON key 1 &
4], or else, it will not function).
Program Remote to recognise the panel
Press section [201][Press Button A slowly and firmly on remote control no.1 TWO times](you will hear a
confirmation beep).
Press section [202][Press Button A slowly and firmly on remote control no.2 TWO times](you will hear a
confirmation beep).
.up to [216] for remote control 16
E: 4-PGM output module (APR3-PGM4)
F: 8 zone hardwire module (APR3-ZX8)
Section 003, enter [003], input 1 on board for 45 ms for vibration sensor
Section 005, enter [003], input 2 on board for 45 ms for vibration sensor
Section 007, enter [003], input 3 on board for 45 ms for vibration sensor
Section 009, enter [003], input 4 on board for 45 ms for vibration sensor
Section 011, enter [003], input 5 on board for 45 ms for vibration sensor
Section 013, enter [003], input 6 on board for 45 ms for vibration sensor
Section 015, enter [003], input 7 on board for 45 ms for vibration sensor
Section 017, enter [003], input 8 on board for 45 ms for vibration sensor
Note: 001 for 15 ms, 002 for 30ms, 003 for 45ms, 004 for 60 ms..default is 600ms
G: 4 zone hardwire module (APR3-ZX4)
Section 003, enter [003], input 1 on board for 45 ms for vibration sensor
Section 005, enter [003], input 2 on board for 45 ms for vibration sensor
Section 007, enter [003], input 3 on board for 45 ms for vibration sensor
Section 009, enter [003], input 4 on board for 45 ms for vibration sensor
Note: 001 for 15 ms, 002 for 30ms, 003 for 45ms, 004 for 60 ms..default is 600ms
H: 1 zone hardwire module (DGP2-ZX1)
Section 003, enter [003], input 1 on board for 45 ms for vibration sensor
Note: 001 for 15 ms, 002 for 30ms, 003 for 45ms, 004 for 60 ms..default is 600ms
I: InTouch voice arm / disarm module (APR3-ADM2)
Section 001, enter [015], 15 ring count (default: 8 rings)
Misc. 1 - Utility
Walk test where Siren will squawk to indicate opened zones
To active
To De-active
: Press & hold [0], then enter [000000], press [MEM] [ENTER] [CLEAR]
: Press & hold [0], then enter [000000], press [MEM] [ENTER] [CLEAR]
Note: MUST de-active or else system cannot be armed even though keypad shows Ready.
Clear TBL 8 Timer loss
Press [TRBL] key, then [8] key, enter [HH:MM] then [YYYYMMDD],[CLEAR]
E.g.: Press [TRBL] key, then [8] key, enter [15:30] then [2000830],[CLEAR]
Answer Winload software / pickup the line
Press & hold [0], then enter [000000], press [ARM]
Cancel dialer
Press & hold [0], then enter [000000], press [DISARM]
Start module scan
Press & hold [0], then enter [000000], press [TRBL]
The keypad will display the serial number of each module on the bus
Read voltage at keypad bus
Press & hold [0], then enter [000000], press [ACC]
A reading of 12.3V or lower that indicates voltage is too low
Misc. 2 Default setting
Display serial number of control panel and all modules
Keypad will display the 8-digit serial number of control panel and all modules
Press & hold [0], then enter [000000], you are in the programming mode
Then, key in [900], use [^] and [V] to scroll.
Module reset
Reset a modules programming contents to default by entering its serial number
Press & hold [0], then enter [000000], you are in the programming mode
Then, key in [951], then enter [8-digits serial number], the module will be defaulted.
Remove modules
Control panel will scan all modules connected to the bus and remove those modules already disconnected.
Press & hold [0], then enter [000000], you are in the programming mode
Then, key in [955], wait for few minutes and it will exit programming mode by itself.
Default master code to 1234 (user code 02 onward remains)
To reset missing master code back to default:1234
Put the RESET jumper on the control panel to ON (shorting)
Press & hold [0], then enter [000000], you are in the programming mode
Then, key in [950]. Remember to remove the RESET jumper to OFF (not shorting)
10
SECTION C: User Functions
Normal function:
Regular Arming
Stay Arming
Instant Arming
Force Arming
Bypass
Disarm
Key in [4 digit user code], then press [ARM]
Key in [4 digit user code], then press [STAY], meaning bypass PIR zone
Key in [4 digit user code], then press [INSTANT = Key5]
Key in [4 digit user code], then press [FORCE]
Key in [4 digit user code], then press [BYP], ENTER [2 digit zone] &[ENTER]
Key in [4 digit user code]
Note: Regular arming will be same as Stay arming if the Delay zone is NOT open during exit delay time.
One-Touch Button:
Arm
Stay
Force
Instant
Press [ARM]
Press [STAY]
Press [FORCE]
Press [INSTANT=Key 5]
Panic function:
Press [1] & [3] at the same time, for Emergency panic alarm.
Press [4] & [6] at the same time, for Auxiliary panic alarm.
Press [7] & [9] at the same time, for Fire panic alarm.
Activating a chime zone:
Enter [4 digit user code], then press [9], [1][2digit zone number], [CLEAR] to exit
Change Master / create new user code
Enter [master code], Press & hold [0], press [ACC] [ 2 digit user, 01 for master, 02 for user 2] [4 digits new code][
ON key for user options], press [], then on key [1]
E.g.:
[1234] [Press & hold [0] [ACC][01] [5678][ON key 6,7][ ENTER], where 01 is master user and 5678 is the new
master code.
[1234] [Press & hold [0] [ACC][02] [7878][ON key 6,7][ ENTER], where 02 is user 2 and 7878 is the user 2 code.
[1234] [Press & hold [0] [ACC][09] [5354][ON key 3,6,7][ ENTER], where 09 is duress code.
11
Partitioning (2-partition)
STEP 1: Zone programming
Press & hold [0], then enter [000000], you are in the programming mode
Press section [101], [6,1, ENTER, CLEAR], means ZONE 1 Instant, Partition 1.
Press section [102], [6,1, ENTER, CLEAR], means ZONE 2 Instant, Partition 1.
Press section [103], [6,2, ENTER, CLEAR], means ZONE 3 Instant, Partition 2.
Press section [104], [6,2, ENTER, CLEAR], means ZONE 4 Instant, Partition 2.
Press section [105], [1,1, ENTER, CLEAR], means ZONE 5 Delay, Partition 1.
STEP 2: Enable features
Section 500, ON key [2 & 6], 1 and 5 remain ON
Section 510, ON key [1,2,3,4,5 & 6]
STEP 3: User authority (NOT in Installation programming, BUT in master programming) [LCD keypad User
manual page 30]
Enter [master code - 1234], press [[PRG], [ACC], then key in [02], key in [new user 2 code- 2222], press [^], user
options [ON 4 & 8], press [^], assign area [ON 2], then press [ENTER][CLEAR]
STEP 4: User operation (Master code:1234)
To arm: [1234][ARM][0][1 and 2], arm partition 1 and 2
To disarm partition 2: [2222][DISARM]
To disarm both partitions: [1234][DISARM][0]
V4.00 26092005
12
FAQ How to wire a smoke detector on Digiplex 848
Diagram for additional RELAY board (12V DC coil and AC/DC contact) to reset smoke detector, you also need to
program PGM output, as follows:
Press & hold [0], then enter [000000], you are in the programming mode
Step 1:
Section [400], enter [41] then [ON key 5][ENTER][CLEAR]
To reset smoke detector once trigger: Press and hold [ENTER] & [CLEAR] for 2 seconds.
Step 2:
Program zone type to Fire zone, value is [A]
Example:
Press section [108], [A,1, ENTER], means ZONE 8 is FIRE zone, Partition 1.
Step 3: Wiring
Digiplex 848
PGM1 PGM2
Aux
+
To
zone
Smoke
detector
Relay
NO
COM
NC
+
13
Programming Planning Sheet
Module type
Main board DGP-848
8-digits serial
number
Assigned zone
number
Located at
1 to 8
Keypad 1
14
