Contents
GSM:..........................................................................................................................................2
To turn on the power for ALD................................................................................................2
To check the receiving power.................................................................................................2
Scan ALD...............................................................................................................................2
TMA.......................................................................................................................................3
ADD TMA.........................................................................................................................3
TMA status.........................................................................................................................3
Set Attenuation...................................................................................................................3
RET........................................................................................................................................3
ADD RET...........................................................................................................................3
Set Tilt................................................................................................................................4
RET status..........................................................................................................................4
Loading RET configuration file.........................................................................................4
Load the file from M2000 to BSC OMU.......................................................................5
Load from BSC OMU to BTS RET...............................................................................5
Calibrate RET:....................................................................................................................5
ALD configuration
GSM:
To turn on the power for ALD
SET
BTSRXUBP:IDTYPE=BYNAME,BTSNAME="XXXBS1",RXUIDTYPE=RXUNAME,RXUNA
ME = "0-40",RXUTYPE=MRFU,PWRSWITCHA=ON,CHKMODA=TMA12DB_ONLY_NON_AISG;
For setting ALD current threshold CHKMODA, refer the following table
Threshold type
TMA12DB_ONLY_NON_AISG
RET_ONLY_COAXIAL
TMA12DB_AISG
ALD
device
TMA only
RET only
TMA & RET
To check the receiving power
DSP
BTSBRD:INFOTYPE=RUNPARA,IDTYPE=BYID,BTSID=10,BRDTYPE=RXU,RXUIDTYP
E=RXUNAME,RXUNAME="0-4-0";
Scan ALD
STR BTSALDSCAN:IDTYPE=BYID,BTSID=10;
To scan particular RF unit, please give additional info in the command.
TMA
ADD TMA
ADD
BTSTMA:IDTYPE=BYID,BTSID=10,DEVICENO=0,DEVICENAME="XXX1G_TMA0",PW
RSUPPLYTYPE=SINGLE_PORT_POWER,CTRLPORTCN=0,CTRLPORTSRN=4,CTRLPOR
TSN=0,SUBUNITNUM=2,VENDORCODE="HW",SERIALNO="1234";
TMA status
To check the status of TMA
DSP BTSTMASUBUNIT:IDTYPE=BYID,BTSID=526;
Set Attenuation
While displaying the status of the TMA, we learn the gain of the TMA.
Actual Gain(0.25db) = 48
= 48*0.25 => 12 db
For a 12db TMA, the attenuation should be between 8 db to 10 db.
Default is 8 db.
SET BTSRXUBP:IDTYPE=BYID,BTSID=10,RXUIDTYPE=RXUNAME,RXUNAME="0-40",RXUTYPE=MRFU,HAVETT1=YES,MRRUATTENFACTOR1=8,HAVETT2=YES,MRRU
ATTENFACTOR2=8;
For Single Feeder[1TX + 2RX] => HAVETT1 & MRRUATTENFACTOR1 is mandatory and
HAVETT2 & MRRUATTENFACTOR2 is optional.
RET
ADD RET
ADD
BTSRET:IDTYPE=BYID,BTSID=10,DEVICENO=0,DEVICENAME="91XXX1G_
RET",CTRLPORTCN=0,CTRLPORTSRN=4,CTRLPORTSN=0,CTRLPORTNO=0,
RETTYPE=SINGLE_RET,SCENARIO=DAISY_CHAIN, VENDORCODE="HW",SE
RIALNO="1234";
For Huawei RET, refer the following table for naming
RET Naming Convention
RET Naming
ConventionNam
e Suffix
r
rr
y
yyR
yL
rr
Ban
d
800
900
210
0
210
0
180
0
900
Layer
Naming convention
J Layer
T Layer
00NAT1J_RET,00NAT2J_RET,00NAT3J_RET
00NAT1T_RET,00NAT2T_RET,00NAT3T_RET
U layer
00NAT1U_RET,00NAT2U_RET,00NAT3U_RET
U layer
00NAT1U_RET,00NAT2U_RET,00NAT3U_RET
K Layer
00NAT1K_RET,00NAT2K_RET,00NAT3K_RET
G900
00NAT1G_RET,00NAT2G_RET,00NAT3G_RET
Set Tilt
MOD
BTSRETTILT:IDTYPE=BYID,BTSID=1,OPMODE=DEVICENO,DEVICENO=0,TI
LT=100;
The tilt should never be left to Zero.
If the value in PAX is ZERO, please contact Karthik Raman.
RET status
DSP BTSRETSUBUNIT:IDTYPE=BYID,BTSID=XXX;
For Huawei RET, we dont need configuration files.
For Katherin RET, refer the below section.
Loading RET configuration file
RET Antenna Data Loss, alarm will appear if there is no config file. All config file are in
M2000.
/!\ Please use filezilla to login into M2000 and find your corresponding .bin file. /!\
Load the file from M2000 to BSC OMU
DLD
BTSALDFILE:IP="10.100.5.153",USR="ftpuser",PWD="*****",DIR="/Ante
nna/Kathrein",FN="KA_80010122V01_790-960_extended2_03-05.bin ";
Load from BSC OMU to BTS RET
LOD
BTSRETCFGDATA:IDTYPE=BYNAME,BTSNAME="71TLYBS1",OPMODE=SITE,FN="KA_80010
122V01_790-960_extended2_03-05.bin";
Calibrate RET:
In few cases, alarm RET antenna not calibrated will occur.
Execute the following command to calibrate RET.
CLB BTSRET:IDTYPE=BYID,BTSID=10,DEVICENO=0,SUBUNITNO=1;
