Scribd
Upload
57 views

Readme en

1) Install PowerMILL 2012, Exchange 2012 and PostProcessor 2012. Install PowerSHAPE if required. Rename a connected USB flash drive in the registry to allow PowerMILL and PowerSHAPE to run without freezing. 2) Open the registry editor, find the hardware ID of the USB flash drive, give yourself full permissions to its registry key, and rename its DeviceDesc value to "SafeNet USB Device". 3) This renames the drive in the operating system and also installs emulator devices to allow running PowerMILL and PowerSHAPE without the flash drive connected.

Uploaded by

haclongdaica1987
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
57 views

Readme en

1) Install PowerMILL 2012, Exchange 2012 and PostProcessor 2012. Install PowerSHAPE if required. Rename a connected USB flash drive in the registry to allow PowerMILL and PowerSHAPE to run without freezing. 2) Open the registry editor, find the hardware ID of the USB flash drive, give yourself full permissions to its registry key, and rename its DeviceDesc value to "SafeNet USB Device". 3) This renames the drive in the operating system and also installs emulator devices to allow running PowerMILL and PowerSHAPE without the flash drive connected.

Uploaded by

haclongdaica1987
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

1) Install PowerMILL 2012, Exchange 2012 and PostProcessor 2012.

Install
PowerSHAPE if required.
2) In Crack folder run installer of the emulator , separately for 32-bit and 64-bit.

Press:
1 for install emulator
2 for restart emulator
3 for remove emulator
4 exit
Note: for 64-bit Windows 8 and 10 before installing the emulator
run command line as administrator and execute command:
bcdedit.exe -set "{current}" bootmenupolicy legacy
Restart the computer - and during boot press F8 key and select - Disable
Driver Signature Enforcement and press Enter.

Renaming USB-flash drive


For correct work, you need to connect any USB flash drive and rename it in
the registry. USB flash drive must be constantly connected. Without it PowerMILL and PowerSHAPE will be freeze in a few minutes.
USB flash drive with USB 3.0 have some troubles, so it is better to use USB
2.0 device.
First of all we must find hardware ID of our USB flash drive .
Run Device Manager and open submenu USB controllers

Then open Properties window of our USB Mass Storage Device, go to the
Details tab and find Hardware Ids string.
In my case this is - VID_8564&PID_1000.
Remember this values, or dont close this window.

Open the Registry Editor (Start-Run-regedit) and go to the address HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB

Find here of our values - VID_8564&PID_1000, and on serial number (in my case
this is O2YPXVIZ5QMTABWD) click right mouse button Permissions

Now we must make yourself the owner.


How to become an owner in the Windows XP, Vista, 7 :

How to become an owner in the Windows 8 and 10 :

In my case - Feod it is my username on my PC. You must choose your username.


Then press and close all windows except the last (Permissions).
In the Permissions window select Everyone, then check box Full Control Allow,
then click Apply and close this window.

Now we have full access, and we can change the name of the USB flash drive.
In the Registry Editor, click the mouse on the serial number of the USB flash drive
- and on the right side you should see a list of options. Double click on the
parameter DeviceDesc, and in the Value data box, type SafeNet USB Device

If everything was done correctly then in the device manager we can find two
new devices:
SafeNet USB Device it is our USB flash drive
SafeNet USB SuperPro/UltraPro it is emulator

Additional information:
Im adding installer of Delcam PowerSHAPE 2012 SP7.
If you need to use PowerMILL Modelling or Delcam Electrode install it.
PS_Doc_2012_English it is english documentation for PowerSHAPE.
The program PS_TrodeExtension_2014_R2 allow to extract data from *.trode
files without running PowerSHAPE. This program integrating in the context
menu of the Windows Explorer.

If you need to install emulator for the other programs, for example for SolidCAM
- import the dump to the Windows Registry, run MK_installer and select 2 restart.

You might also like