Ec Engine Control System
Uploaded by
UALU333Ec Engine Control System
Uploaded by
UALU333ENGINE
SECTION
EC
ENGINE CONTROL SYSTEM
EC
CONTENTS
QR25DE
Air Fuel Ratio (A/F) Sensor 1 ..................................24
Heated Oxygen Sensor 2 ........................................25
Knock Sensor ..........................................................25
Engine Oil Pressure Sensor ....................................26
Engine Oil Temperature Sensor ..............................26
Cooling Fan .............................................................26
EVAP Canister .........................................................27
EVAP Canister Purge Volume Control Solenoid
Valve ........................................................................27
EVAP Canister Vent Control Valve ..........................27
EVAP Control System Pressure Sensor ..................27
Refrigerant Pressure Sensor ...................................28
Stop Lamp Switch & Brake Pedal Position Switch....28
ASCD Steering Switch .............................................28
Information Display ..................................................28
PRECAUTION ............................................... 8
PRECAUTIONS ................................................... 8
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 8
Precaution for Procedure without Cowl Top Cover...... 8
On Board Diagnostic (OBD) System of Engine
and CVT .................................................................... 8
General Precautions ................................................. 9
PREPARATION ........................................... 12
PREPARATION ..................................................12
Special Service Tools .............................................. 12
Commercial Service Tools ...................................... 12
STRUCTURE AND OPERATION ..................... 29
SYSTEM DESCRIPTION ............................. 14
Positive Crankcase Ventilation ................................29
On Board Refueling Vapor Recovery (ORVR) ........30
COMPONENT PARTS .......................................14
SYSTEM ............................................................ 31
Component Parts Location .................................... 14
ECM ........................................................................ 18
Accelerator Pedal Position Sensor .......................... 18
Electric Throttle Control Actuator ............................ 19
Ignition Coil With Power Transistor ......................... 19
Fuel Injector ............................................................ 20
Fuel Level Sensor Unit and Fuel Pump .................. 20
Fuel Tank Temperature Sensor .............................. 20
Mass Air Flow Sensor (With Intake Air Temperature Sensor) ............................................................ 21
Engine Coolant Temperature Sensor ...................... 21
Crankshaft Position Sensor (POS) .......................... 22
Camshaft Position Sensor (PHASE) ....................... 22
Intake Valve Timing Control Solenoid Valve ........... 23
Intake Valve Timing Intermediate Lock Control
Solenoid Valve ........................................................ 23
Exhaust Valve Timing Control Position Sensor ....... 23
Exhaust Valve Timing Control Solenoid Valve ........ 24
Intake Manifold Runner Control Valve .................... 24
ENGINE CONTROL SYSTEM ...................................31
ENGINE CONTROL SYSTEM : System Description ...........................................................................31
ENGINE CONTROL SYSTEM : Circuit Diagram ....33
ENGINE CONTROL SYSTEM : Fail Safe ..............34
Revision: August 2014
MULTIPORT FUEL INJECTION SYSTEM ................37
MULTIPORT FUEL INJECTION SYSTEM : System Description (with automatic air conditioner) ......37
MULTIPORT FUEL INJECTION SYSTEM : System Description (with manual air conditioner) .........39
ELECTRIC IGNITION SYSTEM .................................41
ELECTRIC IGNITION SYSTEM : System Description ...................................................................41
INTAKE VALVE TIMING CONTROL .........................42
INTAKE VALVE TIMING CONTROL : System Description ...................................................................42
EXHAUST VALVE TIMING CONTROL .....................44
EC-1
2015 Rogue NAM
EXHAUST VALVE TIMING CONTROL : System
Description .............................................................. 45
Diagnosis Description ............................................. 58
GST (Generic Scan Tool) ....................................... 58
INTAKE MANIFOLD RUNNER CONTROL .............. 45
INTAKE MANIFOLD RUNNER CONTROL : System Description ....................................................... 46
DIAGNOSIS SYSTEM (ECM) ............................ 59
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE .............................................. 46
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE : System Description ......... 46
AIR CONDITIONING CUT CONTROL ...................... 46
AIR CONDITIONING CUT CONTROL : System
Description .............................................................. 47
POWER GENERATION VOLTAGE VARIABLE
CONTROL SYSTEM ................................................. 47
POWER GENERATION VOLTAGE VARIABLE
CONTROL SYSTEM : System Description ............ 47
COOLING FAN CONTROL ....................................... 47
COOLING FAN CONTROL : System Description... 48
AUTOMATIC SPEED CONTROL DEVICE (ASCD)... 49
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description ....................................... 49
FUEL FILLER CAP WARNING SYSTEM ................. 50
FUEL FILLER CAP WARNING SYSTEM : System
Description .............................................................. 50
WARNING/INDICATOR/CHIME LIST ....................... 51
WARNING/INDICATOR/CHIME LIST : Warning
lamps/Indicator lamps ............................................. 51
WARNING/INDICATOR/CHIME LIST : Warning/
Indicator (On Information Display) .......................... 51
WARNING/INDICATOR/CHIME LIST : Malfunction Indicator Lamp (MIL) ........................................ 51
WARNING/INDICATOR/CHIME LIST : Engine Oil
Pressure Warning ................................................... 53
WARNING/INDICATOR/CHIME LIST : Fuel Filler
Cap Warning ........................................................... 54
EVAPORATIVE EMISSION SYSTEM ....................... 54
EVAPORATIVE EMISSION SYSTEM : System
Description .............................................................. 55
CAN COMMUNICATION ........................................... 55
CAN COMMUNICATION : System Description ...... 55
SPORT MODE CONTROL ........................................ 56
SPORT MODE CONTROL : System Description ... 56
DIAGNOSIS DESCRIPTION ..................................... 59
DIAGNOSIS DESCRIPTION : 1st Trip Detection
Logic and Two Trip Detection Logic ........................ 59
DIAGNOSIS DESCRIPTION : DTC and Freeze
Frame Data ............................................................. 59
DIAGNOSIS DESCRIPTION : Counter System ...... 60
DIAGNOSIS DESCRIPTION : Driving Pattern ........ 63
DIAGNOSIS DESCRIPTION : System Readiness
Test (SRT) Code ..................................................... 64
DIAGNOSIS DESCRIPTION : Permanent Diagnostic Trouble Code (Permanent DTC) .................. 65
DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL) ........................................................ 66
On Board Diagnosis Function ................................. 66
CONSULT Function ................................................ 69
ECU DIAGNOSIS INFORMATION ............. 80
ECM ................................................................... 80
Reference Value ..................................................... 80
Fail Safe ................................................................. 92
DTC Inspection Priority Chart ............................... 95
DTC Index .............................................................. 96
Test Value and Test Limit ..................................... 100
WIRING DIAGRAM ................................... 108
ENGINE CONTROL SYSTEM .......................... 108
Wiring Diagram ..................................................... 108
BASIC INSPECTION ................................. 130
DIAGNOSIS AND REPAIR WORKFLOW ........ 130
Work Flow ............................................................. 130
Diagnostic Work Sheet ......................................... 133
BASIC INSPECTION ........................................ 135
Work Procedure .................................................... 135
ADDITIONAL SERVICE WHEN REPLACING
ECM .................................................................. 139
Description ............................................................ 139
Work Procedure .................................................... 139
VIN REGISTRATION ........................................ 141
Description ............................................................ 141
Work Procedure .................................................... 141
ECO MODE CONTROL ............................................ 56
ECO MODE CONTROL : System Description ........ 56
ACCELERATOR PEDAL RELEASED POSITION LEARNING .............................................. 142
OPERATION ...................................................... 57
Description ............................................................ 142
Work Procedure .................................................... 142
AUTOMATIC SPEED CONTROL DEVICE (ASCD)... 57
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function ........................... 57
THROTTLE VALVE CLOSED POSITION
LEARNING ....................................................... 143
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..... 58
Revision: August 2014
Description ............................................................ 143
Work Procedure .................................................... 143
EC-2
2015 Rogue NAM
IDLE AIR VOLUME LEARNING ...................... 144
Description ............................................................ 144
Work Procedure .................................................... 144
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR .............................................................. 146
Diagnosis Procedure ............................................. 185
Component Inspection ........................................... 186
P0030, P0031, P0032 A/F SENSOR 1 HEATER .................................................................... 188
Description ............................................................ 146
Work Procedure .................................................... 146
DTC Description .................................................... 188
Diagnosis Procedure ............................................. 188
Component Inspection ........................................... 189
FUEL PRESSURE ............................................ 147
P0037, P0038 HO2S2 HEATER ..................... 191
Work Procedure .................................................... 147
DTC Description .................................................... 191
Diagnosis Procedure ............................................. 191
Component Inspection ........................................... 192
HOW TO SET SRT CODE ................................ 148
Description ............................................................ 148
SRT Set Driving Pattern ........................................ 149
Work Procedure .................................................... 151
EC
P0075 INTAKE VALVE TIMING CONTROL ... 194
E
Description ............................................................ 154
Work Procedure (Group A) ................................... 155
Work Procedure (Group B) ................................... 157
DTC Description .................................................... 194
Diagnosis Procedure ............................................. 194
Component Inspection (IVT Control Solenoid
Valve) .................................................................... 196
Component Inspection (IVT Intermediate Lock
Control Solenoid Valve) ......................................... 197
DTC/CIRCUIT DIAGNOSIS ....................... 160
P0078 EVT CONTROL SOLENOID VALVE ... 198
TROUBLE DIAGNOSIS - SPECIFICATION
VALUE .............................................................. 160
DTC Description .................................................... 198
Diagnosis Procedure ............................................. 198
Component Inspection ........................................... 199
HOW TO ERASE PERMANENT DTC .............. 154
Description ............................................................ 160
Component Function Check .................................. 160
Diagnosis Procedure ............................................. 161
P0101 MAF SENSOR ..................................... 201
DTC Description .................................................... 201
Diagnosis Procedure ............................................. 202
Component Inspection ........................................... 203
P0102, P0103 MAF SENSOR ......................... 205
POWER SUPPLY AND GROUND CIRCUIT .... 168
Diagnosis Procedure ............................................. 168
U0101 CAN COMM CIRCUIT ........................... 172
Description ............................................................ 172
DTC Description .................................................... 172
Diagnosis Procedure ............................................. 172
U1001 CAN COMM CIRCUIT ........................... 173
Description ............................................................ 173
DTC Description .................................................... 173
Diagnosis Procedure ............................................. 173
U1040 ENG COMM CIRCUIT ........................... 174
DTC Description .................................................... 205
Diagnosis Procedure ............................................. 206
Component Inspection ........................................... 207
DTC Description .................................................... 209
Diagnosis Procedure ............................................. 210
Component Inspection ........................................... 210
P0112, P0113 IAT SENSOR ........................... 211
DTC Description .................................................... 211
Diagnosis Procedure ............................................. 211
Component Inspection ........................................... 212
U1044 ENG COMM CIRCUIT ........................... 176
P0116 ECT SENSOR ...................................... 214
DTC Description .................................................... 214
Diagnosis Procedure ............................................. 215
Component Inspection ........................................... 215
U1050, U1051 LIN COMMUNICATION ............ 178
DTC Description .................................................... 178
Diagnosis Procedure ............................................. 178
DTC Description .................................................... 216
Diagnosis Procedure ............................................. 216
Component Inspection ........................................... 217
P0122, P0123 TP SENSOR ............................ 219
P0014 EVT CONTROL ..................................... 184
DTC Description .................................................... 184
Revision: August 2014
P0117, P0118 ECT SENSOR .......................... 216
P0011 IVT CONTROL ...................................... 180
DTC Description .................................................... 180
Diagnosis Procedure ............................................. 181
Component Inspection .......................................... 182
P0111 IAT SENSOR ....................................... 209
DTC Description .................................................... 174
Diagnosis Procedure ............................................. 174
DTC Description .................................................... 176
Diagnosis Procedure ............................................. 176
EC-3
DTC Description .................................................... 219
Diagnosis Procedure ............................................. 219
Component Inspection ........................................... 221
2015 Rogue NAM
P0125 ECT SENSOR ....................................... 222
P0182, P0183 FTT SENSOR ............................ 277
DTC Description ....................................................222
Diagnosis Procedure .............................................223
Component Inspection ...........................................223
DTC Description .................................................... 277
Diagnosis Procedure ............................................. 277
Component Inspection .......................................... 279
P0127 IAT SENSOR ........................................ 224
P0196 EOT SENSOR ....................................... 280
DTC Description ....................................................224
Diagnosis Procedure .............................................224
Component Inspection ...........................................225
DTC Description .................................................... 280
Diagnosis Procedure ............................................. 282
Component Inspection .......................................... 282
P0128 THERMOSTAT FUNCTION ................. 226
P0197, P0198 EOT SENSOR ........................... 284
DTC Description ....................................................226
Diagnosis Procedure .............................................227
Component Inspection ...........................................228
DTC Description .................................................... 284
Diagnosis Procedure ............................................. 284
Component Inspection .......................................... 285
P0130 A/F SENSOR 1 ..................................... 229
P0222, P0223 TP SENSOR .............................. 287
DTC Description ....................................................229
Diagnosis Procedure .............................................230
DTC Description .................................................... 287
Diagnosis Procedure ............................................. 287
Component Inspection .......................................... 289
P0131 A/F SENSOR 1 ..................................... 233
DTC Description ....................................................233
Diagnosis Procedure .............................................234
P0300, P0301, P0302, P0303, P0304 MISFIRE .................................................................. 290
P0132 A/F SENSOR 1 ..................................... 236
DTC Description .................................................... 290
Diagnosis Procedure ............................................. 291
DTC Description ....................................................236
Diagnosis Procedure .............................................237
P0137 HO2S2 .................................................. 239
DTC Description ....................................................239
Diagnosis Procedure .............................................241
Component Inspection ...........................................242
P0138 HO2S2 .................................................. 245
DTC Description ....................................................245
Diagnosis Procedure .............................................247
Component Inspection ...........................................250
P0139 HO2S2 .................................................. 252
P0327, P0328 KS ............................................. 296
DTC Description .................................................... 296
Diagnosis Procedure ............................................. 296
Component Inspection .......................................... 297
P0335 CKP SENSOR (POS) ............................ 298
DTC Description .................................................... 298
Diagnosis Procedure ............................................. 298
Component Inspection (Crankshaft Position sensor) ........................................................................ 300
P0340 CMP SENSOR (PHASE) ....................... 301
DTC Description ....................................................252
Diagnosis Procedure .............................................254
Component Inspection ...........................................256
DTC Description .................................................... 301
Diagnosis Procedure ............................................. 301
Component Inspection (Camshaft position sensor) ........................................................................ 303
P014C, P014D, P015A, P015B, A/F SENSOR
1 ....................................................................... 258
P0420 THREE WAY CATALYST FUNCTION.. 304
DTC Description ....................................................258
Diagnosis Procedure .............................................260
P0171 FUEL INJECTION SYSTEM FUNCTION ................................................................. 263
DTC Description ....................................................263
Diagnosis Procedure .............................................264
P0172 FUEL INJECTION SYSTEM FUNCTION ................................................................. 268
DTC Description ....................................................268
Diagnosis Procedure .............................................269
P0181 FTT SENSOR ....................................... 273
DTC Description ....................................................273
Diagnosis Procedure .............................................275
Component Inspection ...........................................276
Revision: August 2014
DTC Description .................................................... 304
Diagnosis Procedure ............................................. 305
P0441 EVAP CONTROL SYSTEM .................. 309
DTC Description .................................................... 309
Diagnosis Procedure ............................................. 311
P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ........................ 314
DTC Description .................................................... 314
Diagnosis Procedure ............................................. 315
Component Inspection .......................................... 318
P0444, P0445 EVAP CANISTER PURGE
VOLUME CONTROL SOLENOID VALVE ....... 319
DTC Description .................................................... 319
Diagnosis Procedure ............................................. 319
Component Inspection .......................................... 321
EC-4
2015 Rogue NAM
P0447 EVAP CANISTER VENT CONTROL
VALVE .............................................................. 322
P050A, P050B, P050E COLD START CONTROL ............................................................... 359
DTC Description .................................................... 322
Diagnosis Procedure ............................................. 322
Component Inspection .......................................... 324
Description ............................................................. 359
DTC Description .................................................... 359
Diagnosis Procedure ............................................. 360
EC
P0448 EVAP CANISTER VENT CONTROL
VALVE .............................................................. 326
P0520 EOP SENSOR ...................................... 361
DTC Description .................................................... 326
Diagnosis Procedure ............................................. 327
Component Inspection .......................................... 328
DTC Description .................................................... 361
Diagnosis Procedure ............................................. 361
Component Inspection ........................................... 363
P0524 ENGINE OIL PRESSURE .................... 364
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR ................................................ 330
DTC Description .................................................... 330
Diagnosis Procedure ............................................. 331
Component Inspection .......................................... 333
DTC Description .................................................... 364
Diagnosis Procedure ............................................. 365
Component Inspection ........................................... 366
P052A, P052B INTAKE VALVE TIMING CONTROL ............................................................... 367
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR ................................................ 334
DTC Description .................................................... 367
Diagnosis Procedure ............................................. 368
Component Inspection (Intake Valve Timing Control Solenoid Valve) ............................................... 369
Component Inspection (Intake Valve Timing Intermediate Lock Control Solenoid Valve) .................. 370
Component Inspection (Crankshaft Position sensor) ........................................................................ 371
Component Inspection (Camshaft position sensor) ........................................................................ 371
DTC Description .................................................... 334
Diagnosis Procedure ............................................. 335
Component Inspection .......................................... 336
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR ................................................ 337
DTC Description .................................................... 337
Diagnosis Procedure ............................................. 338
Component Inspection .......................................... 340
P0456 EVAP CONTROL SYSTEM .................. 341
DTC Description .................................................... 341
Diagnosis Procedure ............................................. 342
Component Inspection .......................................... 346
P0603, P062F ECM ......................................... 373
DTC Description .................................................... 373
Diagnosis Procedure ............................................. 374
DTC Description .................................................... 375
Diagnosis Procedure ............................................. 375
DTC Description .................................................... 347
Diagnosis Procedure ............................................. 347
P0605 ECM ..................................................... 376
P0461 FUEL LEVEL SENSOR ........................ 349
DTC Description .................................................... 376
Diagnosis Procedure ............................................. 376
DTC Description .................................................... 349
Diagnosis Procedure ............................................. 350
P0606 ECM ..................................................... 377
P0462, P0463 FUEL LEVEL SENSOR ............ 351
DTC Description .................................................... 377
Diagnosis Procedure ............................................. 377
DTC Description .................................................... 351
Diagnosis Procedure ............................................. 351
P0607 ECM ..................................................... 379
DTC Description .................................................... 379
Diagnosis Procedure ............................................. 379
P0500 VSS ....................................................... 353
P0506 ISC SYSTEM ......................................... 355
P060A ECM ..................................................... 380
DTC Description .................................................... 380
Diagnosis Procedure ............................................. 380
Description ............................................................ 355
DTC Description .................................................... 355
Diagnosis Procedure ............................................. 356
P060B ECM ..................................................... 381
P0507 ISC SYSTEM ......................................... 357
P0643 SENSOR POWER SUPPLY ................ 382
DTC Description .................................................... 381
Diagnosis Procedure ............................................. 381
Description ............................................................ 357
DTC Description .................................................... 357
Diagnosis Procedure ............................................. 358
Revision: August 2014
P0604 ECM ..................................................... 375
P0460 FUEL LEVEL SENSOR ........................ 347
Description ............................................................ 353
DTC Description .................................................... 353
Diagnosis Procedure ............................................. 354
EC-5
Description ............................................................. 382
DTC Description .................................................... 382
Diagnosis Procedure ............................................. 383
2015 Rogue NAM
P0850 PNP SWITCH ....................................... 385
Description .............................................................385
DTC Description ....................................................385
Diagnosis Procedure .............................................386
P1078 EVT CONTROL POSITION SENSOR . 388
DTC Description ....................................................388
Diagnosis Procedure .............................................388
Component Inspection ...........................................390
P1148 CLOSED LOOP CONTROL ................. 391
DTC Description ....................................................391
Diagnosis Procedure .............................................391
P117A AIR FUEL RATIO ................................. 392
DTC Description ....................................................392
Diagnosis Procedure .............................................393
P1212 TCS COMMUNICATION LINE ............. 398
Description .............................................................398
DTC Description ....................................................398
Diagnosis Procedure .............................................398
P1217 ENGINE OVER TEMPERATURE ......... 400
DTC Description .................................................... 419
Diagnosis Procedure ............................................. 419
P1805 BRAKE SWITCH ................................... 421
DTC Description .................................................... 421
Diagnosis Procedure ............................................. 421
Component Inspection (Stop Lamp Switch) .......... 422
P2004 INTAKE MANIFOLD RUNNER CONTROL VALVE ................................................... 423
DTC Description .................................................... 423
Diagnosis Procedure ............................................. 423
Component Inspection .......................................... 424
P2014, P2016, P2017, P2018 INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR ................................................. 426
DTC Description .................................................... 426
Diagnosis Procedure ............................................. 427
P2096, P2097 A/F SENSOR 1 ......................... 429
DTC Description .................................................... 429
Diagnosis Procedure ............................................. 429
DTC Description ....................................................400
Diagnosis Procedure .............................................401
P2100, P2103 THROTTLE CONTROL MOTOR RELAY ..................................................... 433
P1225 TP SENSOR ......................................... 403
DTC Description .................................................... 433
Diagnosis Procedure ............................................. 434
DTC Description ....................................................403
Diagnosis Procedure .............................................403
P1226 TP SENSOR ......................................... 404
DTC Description ....................................................404
Diagnosis Procedure .............................................404
P155D GENERATOR ...................................... 405
DTC Description ....................................................405
Diagnosis Procedure .............................................405
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ........................................................ 436
DTC Description .................................................... 436
Diagnosis Procedure ............................................. 436
Component Inspection .......................................... 438
P2118 THROTTLE CONTROL MOTOR .......... 439
P1564 ASCD STEERING SWITCH ................. 406
DTC Description .................................................... 439
Diagnosis Procedure ............................................. 439
Component Inspection .......................................... 440
DTC Description ....................................................406
Diagnosis Procedure .............................................406
Component Inspection ...........................................408
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR ...................................................... 441
P1568 SIGNAL INVALID ................................. 409
DTC Description .................................................... 441
Diagnosis Procedure ............................................. 441
DTC Description ....................................................409
Diagnosis Procedure .............................................409
P2122, P2123 APP SENSOR ........................... 443
P1572 BRAKE PEDAL POSITION SWITCH ... 411
DTC Description ....................................................411
Diagnosis Procedure .............................................412
Component Inspection (Brake Pedal Position
Switch) ...................................................................414
Component Inspection (Stop Lamp Switch) ..........415
P1574 ASCD VEHICLE SPEED SENSOR ...... 417
Description .............................................................417
DTC Description ....................................................417
Diagnosis Procedure .............................................418
P1715 INPUT SPEED SENSOR ...................... 419
Description .............................................................419
Revision: August 2014
DTC Description .................................................... 443
Diagnosis Procedure ............................................. 443
Component Inspection .......................................... 445
P2127, P2128 APP SENSOR ........................... 446
DTC Description .................................................... 446
Diagnosis Procedure ............................................. 446
Component Inspection .......................................... 447
P2135 TP SENSOR .......................................... 449
DTC Description .................................................... 449
Diagnosis Procedure ............................................. 449
Component Inspection .......................................... 451
P2138 APP SENSOR ....................................... 452
EC-6
2015 Rogue NAM
DTC Description .................................................... 452
Diagnosis Procedure ............................................. 452
Component Inspection .......................................... 454
Component Function Check .................................. 480
Diagnosis Procedure ............................................. 480
Component Inspection ........................................... 482
P2610 ECM INTERNAL TIMER ....................... 456
REFRIGERANT PRESSURE SENSOR .......... 485
Description ............................................................ 456
DTC Description .................................................... 456
Diagnosis Procedure ............................................. 457
Component Function Check .................................. 485
Diagnosis Procedure ............................................. 485
EC
SENSOR POWER SUPPLY2 CIRCUIT .......... 487
BRAKE PEDAL POSITION SWITCH ............... 458
Description ............................................................. 487
Diagnosis Procedure ............................................. 487
Component Function Check .................................. 458
Diagnosis Procedure ............................................. 458
Component Inspection (Brake Pedal Position
Switch) .................................................................. 459
SYMPTOM DIAGNOSIS ............................ 489
COOLING FAN ................................................. 461
Symptom Table ..................................................... 489
Component Function Check .................................. 461
Diagnosis Procedure ............................................. 461
Component Inspection (Cooling Fan Motor) ......... 464
Component Inspection (Cooling Fan Relay) ......... 464
ELECTRICAL LOAD SIGNAL ......................... 465
Description ............................................................ 465
Component Function Check .................................. 465
Diagnosis Procedure ............................................. 465
FUEL INJECTOR ............................................. 467
ENGINE CONTROL SYSTEM ........................ 489
INFORMATION DISPLAY IS MALFUNCTIONING .................................................................. 494
Diagnosis Procedure ............................................. 494
NORMAL OPERATING CONDITION ............. 495
Description ............................................................. 495
PERIODIC MAINTENANCE ...................... 496
IDLE SPEED ................................................... 496
Inspection .............................................................. 496
Component Function Check .................................. 467
Diagnosis Procedure ............................................. 467
Component Inspection .......................................... 468
IGNITION TIMING ........................................... 497
FUEL PUMP ..................................................... 470
EVAPORATIVE EMISSION SYSTEM ............. 498
Description ............................................................ 470
Component Function Check .................................. 470
Diagnosis Procedure ............................................. 470
Component Inspection .......................................... 472
Inspection .............................................................. 497
Inspection .............................................................. 498
EVAP LEAK CHECK ...................................... 499
Inspection .............................................................. 499
IGNITION SIGNAL ........................................... 473
POSITIVE CRANKCASE VENTILATION ....... 501
Component Function Check .................................. 473
Diagnosis Procedure ............................................. 473
Component Inspection (Ignition Coil with Power
Transistor) ............................................................. 476
Component Inspection (Condenser) ..................... 477
Inspection .............................................................. 501
REMOVAL AND INSTALLATION ............. 502
ECM ................................................................. 502
Removal and Installation ....................................... 502
Component Function Check .................................. 478
Diagnosis Procedure ............................................. 478
SERVICE DATA AND SPECIFICATIONS
(SDS) .......................................................... 503
MALFUNCTION INDICATOR LAMP ............... 479
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................... 503
INFORMATION DISPLAY (ASCD) .................. 478
Component Function Check .................................. 479
Diagnosis Procedure ............................................. 479
ON BOARD REFUELING VAPOR RECOVERY (ORVR) ..................................................... 480
Revision: August 2014
EC-7
Idle Speed ............................................................. 503
Ignition Timing ....................................................... 503
Calculated Load Value .......................................... 503
Mass Air Flow Sensor ............................................ 503
2015 Rogue NAM
PRECAUTIONS
[QR25DE]
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011277813
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000011277814
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
On Board Diagnostic (OBD) System of Engine and CVT
INFOID:0000000011277815
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:
Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any repair
or inspection work. The open/short circuit of related switches, sensors, solenoid valves, etc. will
cause the MIL to light up.
Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
Certain systems and components, especially those related to OBD, may use a new style slide-locking type harness connector. For description and how to disconnect, refer to PG-7, "Harness Connector".
Be sure to route and secure the harnesses properly after work. The interference of the harness with
a bracket, etc. may cause the MIL to light up due to the short circuit.
Revision: August 2014
EC-8
2015 Rogue NAM
PRECAUTIONS
[QR25DE]
< PRECAUTION >
Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to the malfunction of the EVAP system or fuel injection system,
etc.
Be sure to erase the unnecessary malfunction information (repairs completed) from the ECM and
TCM (Transmission control module) before returning the vehicle to the customer.
General Precautions
EC
INFOID:0000000011277816
Always use a 12 volt battery as power source.
Do not attempt to disconnect battery cables while engine is
running.
Before connecting or disconnecting the ECM harness connector, turn ignition switch OFF and disconnect negative battery cable. Failure to do so may damage the ECM because
battery voltage is applied to ECM even if ignition switch is
turned OFF.
Before removing parts, turn ignition switch OFF and then disconnect battery ground cable.
SEF289H
Do not disassemble ECM.
If a battery cable is disconnected, the memory will return to
the ECM value.
The ECM will now start to self-control at its initial value.
Engine operation can vary slightly when the terminal is disconnected. However, this is not an indication of a malfunction. Do not replace parts because of a slight variation.
If the battery is disconnected, the following emission-related
diagnostic information will be lost within 24 hours.
- Diagnostic trouble codes
- 1st trip diagnostic trouble codes
- Freeze frame data
- 1st trip freeze frame data
- System readiness test (SRT) codes
- Test values
When connecting ECM harness connector , fasten
it
securely with a lever as far as it will go as shown in the figure.
I
PBIA9222J
ECM
Loosen
ALBIA0810ZZ
When connecting or disconnecting pin connectors into or
from ECM, take care not to damage pin terminals (bend or
break).
Make sure that there are not any bends or breaks on ECM pin
terminal, when connecting pin connectors.
Securely connect ECM harness connectors.
A poor connection can cause an extremely high (surge) voltage to develop in coil and condenser, thus resulting in damage to ICs.
Keep engine control system harness at least 10 cm (4 in) away
from adjacent harness, to prevent engine control system malfunctions due to receiving external noise, degraded operation
of ICs, etc.
Revision: August 2014
EC-9
PBIB0090E
2015 Rogue NAM
PRECAUTIONS
< PRECAUTION >
Keep engine control system parts and harness dry.
Before replacing ECM, perform ECM Terminals and Reference
Value inspection and make sure ECM functions properly.
Refer to EC-80, "Reference Value".
Handle mass air flow sensor carefully to avoid damage.
Do not clean mass air flow sensor with any type of detergent.
Do not disassemble electric throttle control actuator.
Even a slight leak in the air intake system can cause serious
incidents.
Do not shock or jar the camshaft position sensor (PHASE),
crankshaft position sensor (POS).
[QR25DE]
MEF040D
After performing each TROUBLE DIAGNOSIS, perform DTC
CONFIRMATION PROCEDURE or Component Function
Check. The DTC should not be displayed in the DTC Confirmation Procedure if the repair is completed. The Component
Function Check should be a good result if the repair is completed.
SAT652J
When measuring ECM signals with a circuit tester, never allow
the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.
SEF348N
Do not operate fuel pump when there is no fuel in lines.
Tighten fuel hose clamps to the specified torque.
Revision: August 2014
EC-10
2015 Rogue NAM
PRECAUTIONS
< PRECAUTION >
Do not depress accelerator pedal when starting.
Immediately after starting, do not rev up engine unnecessarily.
Do not rev up engine just prior to shutdown.
[QR25DE]
A
EC
C
SEF709Y
When installing C.B. ham radio or a mobile phone, be sure to
observe the following as it may adversely affect electronic
control systems depending on installation location.
- Keep the antenna as far as possible from the electronic control units.
- Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
- Adjust the antenna and feeder line so that the standing-wave
ratio can be kept smaller.
- Be sure to ground the radio to vehicle body.
G
SEF708Y
Revision: August 2014
EC-11
2015 Rogue NAM
PREPARATION
[QR25DE]
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000011277817
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
(J-44321)
Fuel pressure gauge
kit
Checks fuel pressure
LEC642
KV10120000
( )
Fuel tube adapter
Measures fuel pressure
JSBIA0410ZZ
Commercial Service Tools
INFOID:0000000011277818
Tool name
(TechMate No.)
Description
Leak detector
i.e.: (J-41416)
Locates the EVAP leak
S-NT703
EVAP service port
adapter
i.e.: (J-41413-OBD)
Applies positive pressure through EVAP service
port
S-NT704
Fuel filler cap adapter
i.e.: (MLR-8382)
Checks fuel tank vacuum relief valve opening
pressure
S-NT815
Revision: August 2014
EC-12
2015 Rogue NAM
PREPARATION
[QR25DE]
< PREPARATION >
Tool name
(TechMate No.)
Description
Socket wrench
i.e.: ( )
Removes and installs engine coolant temperature
sensor
EC
C
S-NT705
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)
Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with antiseize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirconia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Titania Oxygen Sensor
AEM488
F
Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Anti-seize lubricant
i.e.: (PermatexTM
133AR or equivalent
meeting MIL specification MIL-A-907)
H
S-NT779
Revision: August 2014
EC-13
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000011277819
ENGINE ROOM COMPARTMENT
ALBIA1180ZZ
No.
Component
Function
IPDM E/R
IPDM E/R control the internal relays and the actuators.
- Refer to PCS-7, "RELAY CONTROL SYSTEM : System Description".
When CAN communication with ECM is impossible,
IPDM E/R performs fail-safe control.
- Refer to PCS-8, "RELAY CONTROL SYSTEM : Failsafe".
Mass air flow sensor
(with intake air temperature sensor)
EC-21, "Mass Air Flow Sensor (With Intake Air Temperature Sensor)"
Electric throttle control actuator
(with built in throttle position sensor and throttle control motor)
EC-19, "Electric Throttle Control Actuator"
EVAP canister purge volume control solenoid valve
EC-27, "EVAP Canister Purge Volume Control Solenoid
Valve"
Intake manifold runner control valve actuator
EC-24, "Intake Manifold Runner Control Valve"
Refrigerant pressure sensor
EC-28, "Refrigerant Pressure Sensor"
EVAP service port
When perform the EVAP leak check, positive pressure is
delivered to the EVAP system through the EVAP service
port.
Refer to EC-499, "Inspection".
Revision: August 2014
EC-14
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
No.
Component
Function
The transmission range switch is installed to upper part
of transaxle case.
ECM detects the selector lever position because the
continuity of the transmission range switch line (the
ON) exists.
Transmission range switch
ECM
EC
EC-18, "ECM"
ENGINE COMPARTMENT
JSBIA4548ZZ
Engine rear side
Intake side
: Vehicle front
No.
Component
Function
Exhaust valve timing control position sensor
EC-23, "Exhaust Valve Timing Control Position Sensor"
Camshaft position sensor (PHASE)
EC-22, "Camshaft Position Sensor (PHASE)"
PCV valve
The positive crankcase ventilation (PCV) valve is provided
to conduct crankcase blow-by gas to the intake manifold.
Fuel injector
EC-20, "Fuel Injector"
Crankshaft position sensor (POS)
EC-22, "Crankshaft Position Sensor (POS)"
Knock sensor
EC-25, "Knock Sensor"
Engine oil temperature sensor
EC-26, "Engine Oil Temperature Sensor"
Engine oil pressure sensor
EC-26, "Engine Oil Pressure Sensor"
Revision: August 2014
EC-15
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
No.
Component
Function
Intake valve timing intermediate lock control solenoid valve
EC-23, "Intake Valve Timing Intermediate Lock Control Solenoid Valve"
Intake valve timing control solenoid valve
EC-23, "Intake Valve Timing Control Solenoid Valve"
Exhaust valve timing control solenoid valve
EC-24, "Exhaust Valve Timing Control Solenoid Valve"
Ignition coil (with power transistor)
EC-19, "Ignition Coil With Power Transistor"
Engine coolant temperature sensor
EC-21, "Engine Coolant Temperature Sensor"
Intake manifold runner control valve position sensor
EC-24, "Intake Manifold Runner Control Valve"
Intake manifold runner control valve actuator
EXHAUST COMPARTMENT
JPBIA5841ZZ
To engine assembly
No.
Component
Function
Air fuel ratio (A/F) sensor 1
EC-24, "Air Fuel Ratio (A/F) Sensor 1"
Heated oxygen sensor 2
EC-25, "Heated Oxygen Sensor 2"
BODY COMPARTMENT
Revision: August 2014
EC-16
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
EC
ALBIA1181ZZ
Instrument panel area
Periphery of pedals
Inside fuel tank area
Behind fuel tank
: Vehicle front
M
No.
Component
Combination meter
Function
Malfunction indicator lamp (MIL)
EC-51, "WARNING/INDICATOR/CHIME LIST : Malfunction Indicator Lamp (MIL)"
Information display
EC-28, "Information Display"
ASCD steering switch
EC-28, "ASCD Steering Switch"
Stop lamp switch
EC-28, "Stop Lamp Switch & Brake Pedal Position Switch"
Brake pedal position switch
Accelerator pedal position sensor
EC-18, "Accelerator Pedal Position Sensor"
Fuel level sensor unit and fuel pump
EC-20, "Fuel Level Sensor Unit and Fuel Pump"
Fuel tank temperature sensor
EC-20, "Fuel Tank Temperature Sensor"
EVAP control system pressure sensor
EC-27, "EVAP Control System Pressure Sensor"
Revision: August 2014
EC-17
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
No.
Component
Function
EVAP canister vent control valve
EC-27, "EVAP Canister Vent Control Valve"
EVAP canister
EC-27, "EVAP Canister"
ECM
INFOID:0000000011277820
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
JPBIA5843ZZ
Accelerator Pedal Position Sensor
INFOID:0000000011277821
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the ECM.
JPBIA5844ZZ
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometers which transform the accelerator pedal
position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of
the accelerator pedal and feed the voltage signals to the ECM. The
ECM judges the current opening angle of the accelerator pedal from
these signals and controls the throttle control motor based on these
signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for the engine operation such as fuel cut.
Revision: August 2014
EC-18
PBIB1741E
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Electric Throttle Control Actuator
INFOID:0000000011277822
Electric throttle control actuator consists of throttle body, throttle valve, throttle control motor and throttle position sensor.
EC
F
JSBIA0270GB
THROTTLE CONTROL MOTOR RELAY
Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends
an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition
switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not
provided to the ECM.
THROTTLE CONTROL MOTOR
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feedback to the ECM to control the throttle control motor to make the throttle valve opening angle properly in
response to driving condition.
THROTTLE POSITION SENSOR
The throttle position sensor responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
INFOID:0000000011277823
The ignition signal from the ECM is sent to and amplified by the
power transistor. The power transistor turns ON and OFF the ignition
coil primary circuit. This ON/OFF operation induces the proper high
voltage in the coil secondary circuit.
JPBIA4613ZZ
Revision: August 2014
PBIB0145E
Ignition Coil With Power Transistor
EC-19
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Fuel Injector
INFOID:0000000011277824
The fuel injector is a small, precise solenoid valve. When the ECM
supplies a ground to the fuel injector circuit, the coil in the fuel injector is energized. The energized coil pulls the ball valve back and
allows fuel to flow through the fuel injector into the intake manifold.
The amount of fuel injected depends upon the injection pulse duration. Pulse duration is the length of time the fuel injector remains
open. The ECM controls the injection pulse duration based on
engine fuel needs.
JPBIA5845ZZ
Fuel Level Sensor Unit and Fuel Pump
INFOID:0000000011277825
FUEL PUMP
The ECM activates the fuel pump for 1 second after the ignition
switch is turned ON to improve engine start ability. If the ECM
receives a engine speed signal from the camshaft position sensor
(PHASE), it knows that the engine is rotating, and causes the pump
to operate. If the engine speed signal is not received when the ignition switch is ON, the engine stalls. The ECM stops pump operation
and prevents battery discharging, thereby improving safety. The
ECM does not directly drive the fuel pump. It sends the control signal
to the fuel pump control module, which in turn controls the fuel
pump.
JSBIA4496ZZ
Condition
Fuel pump operation
Ignition switch is turned to ON.
Operates for 1 second.
Engine running and cranking
Operates.
When engine is stopped
Stops in 1.5 seconds.
Except as shown above
Stops.
FUEL LEVEL SENSOR
The fuel level sensor is mounted in the fuel level sensor unit.
The sensor detects a fuel level in the fuel tank and transmits a signal to the combination meter. The combination meter sends the fuel level sensor signal to the ECM via the CAN communication line.
It consists of two parts, one is mechanical float and the other is variable resistor. Fuel level sensor output voltage changes depending on the movement of the fuel mechanical float.
Fuel Tank Temperature Sensor
INFOID:0000000011277826
The fuel tank temperature sensor is used to detect the fuel temperature inside the fuel tank. The sensor modifies a voltage signal from
the ECM. The modified signal returns to the ECM as the fuel temperature input. The sensor uses a thermistor which is sensitive to the
change in temperature. The electrical resistance of the thermistor
decreases as temperature increases.
SEF012P
<Reference data>
Revision: August 2014
EC-20
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Fluid temperature
[C (F)]
Voltage* (V)
Resistance (k)
20 (68)
3.5
2.3 - 2.7
50 (122)
2.2
0.79 - 0.90
EC
*: These data are reference values and are measured between ECM terminals.
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
INFOID:0000000011277827
MASS AIR FLOW SENSOR
The mass air flow sensor is placed in the stream of intake air. It
measures the intake flow rate by measuring a part of the entire
intake flow. The MAF sensor controls the temperature of the heater
in sensing element to a certain amount. The temperature distribution
around the heater changes according to the increase in intake air
volume. The change is detected by a thermistor and the air volume
data is sent to ECM by the MAF sensor.
PBIA9559J
INTAKE AIR TEMPERATURE SENSOR
The intake air temperature sensor is built-into mass air flow sensor. The sensor detects intake air temperature
and transmits a signal to the ECM.
The temperature sensing unit uses a thermistor which is sensitive to the change in temperature.
<Reference data>
Intake air temperature
[C (F)]
Voltage* (V)
25 (77)
1.9 2.1
80 (176)
3.2 3.4
*: These data are reference values on the diagnosis tool.
Engine Coolant Temperature Sensor
INFOID:0000000011277828
The engine coolant temperature sensor is used to detect the engine
coolant temperature. The sensor modifies a voltage signal from the
ECM. The modified signal returns to the ECM as the engine coolant
temperature input. The sensor uses a thermistor which is sensitive to
the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.
O
JPBIA5280ZZ
Revision: August 2014
EC-21
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
<Reference data>
Engine coolant temperature
[C (F)]
Voltage* (V)
Resistance (k)
10 (14)
4.4
7.0 - 11.4
20 (68)
3.5
2.37 - 2.63
50 (122)
2.2
0.68 - 1.00
90 (194)
1.0
0.236 - 0.260
*: These data are reference values and are measured between ECM terminals.
Crankshaft Position Sensor (POS)
SEF012P
INFOID:0000000011277829
The crankshaft position sensor (POS) is located on the oil pan facing
the gear teeth (cogs) of the signal plate. It detects the fluctuation of
the engine revolution.
The sensor consists of a permanent magnet and Hall IC.
When the engine is running, the high and low parts of the teeth
cause the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor
changes.
The ECM receives the voltage signal and detects the fluctuation of
the engine revolution.
ECM receives the signals as shown in the figure.
JPBIA5848ZZ
JMBIA0714GB
Camshaft Position Sensor (PHASE)
INFOID:0000000011277830
The camshaft position sensor (PHASE) senses the retraction of
intake camshaft to identify a particular cylinder. The camshaft position sensor (PHASE) senses the piston position.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor (PHASE) provides various controls of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
Revision: August 2014
EC-22
JPBIA5846ZZ
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
ECM receives the signals as shown in the figure.
EC
C
JMBIA0714GB
Intake Valve Timing Control Solenoid Valve
D
INFOID:0000000011277831
Intake valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The intake valve timing control solenoid valve changes the oil
amount and direction of flow through intake valve timing control unit
or stops oil flow.
The longer pulse width advances valve angle.
The shorter pulse width retards valve angle.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the intake valve angle at the control
position.
G
PBIB1842E
Intake Valve Timing Intermediate Lock Control Solenoid Valve
Intake valve timing intermediate lock control solenoid valve is activated by ON/OFF signals from the ECM.
The intake valve timing intermediate lock control solenoid valve
opens/closes the path of oil pressure acting on the lock key in the
camshaft sprocket (INT).
When the solenoid valve becomes ON, oil pressure to the lock key
is trained to perform intermediate lock.
When the solenoid valve becomes OFF, oil pressure is acted on
the lock key to release the intermediate lock.
PBIB1842E
Exhaust Valve Timing Control Position Sensor
Exhaust valve timing control position sensor detects the protrusion of
the signal plate installed to the exhaust camshaft front end.
This sensor signal is used for sensing a position of the exhaust camshaft.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor
changes.
Revision: August 2014
EC-23
INFOID:0000000011277832
INFOID:0000000011277833
JPBIA5847ZZ
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Exhaust Valve Timing Control Solenoid Valve
INFOID:0000000011277834
Exhaust valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The exhaust valve timing control solenoid valve changes the oil
amount and direction of flow through exhaust valve timing control
unit or stops oil flow.
The longer pulse width retards valve angle.
The shorter pulse width advances valve angle.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the exhaust valve angle at the control
position.
PBIB1842E
Intake Manifold Runner Control Valve
INFOID:0000000011277835
Intake manifold runner control valve is integrated to intake manifold.
Intake manifold runner control valve is mounted each port of the
intake manifold and opened/closed by the intake manifold runner
control valve motor.
ECM controls the intake manifold runner control valve motor, according to signals of engine speed, water temperature, etc. and stabilizes
combustion by generating a strong tunmble flow.
JSBIA4549ZZ
INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR
Intake manifold runner control valve motor is connected to the rear end of the valve shaft.
The motor opens or closes the valve by the output signal of the ECM.
INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR
Intake manifold runner control valve position sensor is connected to the front end of the valve shaft.
The sensor consists of valiable resister. It senses the valve shaft movement and feeds the voltage signals to
the ECM.
Air Fuel Ratio (A/F) Sensor 1
INFOID:0000000011277836
The sensor element of the A/F sensor 1 is composed an electrode
layer, which transports ions. It has a heater in the element.
JPBIA4038GB
The sensor is capable of precise measurement = 1, but also in the lean and rich range. Together with its
control electronics, the sensor outputs a clear, continuous signal throughout a wide range.
The exhaust gas components diffuse through the diffusion layer at the sensor cell. An electrode layer is
applied voltage, and this current relative oxygen density in lean. Also this current relative hydrocarbon density
in rich.
Revision: August 2014
EC-24
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Therefore, the A/F sensor 1 is able to indicate air fuel ratio by this
electrode layer of current. In addition, a heater is integrated in the
sensor to ensure the required operating temperature of approximately 760C (1,400F).
EC
C
JPBIA5446GB
A/F SENSOR 1 HEATER
A/F sensor 1 heater is integrated in the sensor.
The ECM performs ON/OFF duty control of the A/F sensor 1 heater corresponding to the engine operating
condition to keep the temperature of A/F sensor 1 element within the specified range.
Heated Oxygen Sensor 2
INFOID:0000000011277837
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas.
Even if switching characteristics of the air fuel ratio (A/F) sensor 1
are shifted, the air fuel ratio is controlled to stoichiometric, by the signal from the heated oxygen sensor 2.
This sensor is made of ceramic zirconia. The zirconia generates voltage from approximately 1 V in richer conditions to 0 V in leaner conditions.
Under normal conditions the heated oxygen sensor 2 is not used for
engine control operation.
SEF327R
HEATED OXYGEN SENSOR 2 HEATER
Heated oxygen sensor 2 heater is integrated in the sensor.
The ECM performs ON/OFF control of the heated oxygen sensor 2 heater corresponding to the engine speed,
amount of intake air and engine coolant temperature.
Engine speed
Heated oxygen sensor 2 heater
Above 3,600 rpm
OFF
Below 3,600 rpm after the following conditions are met.
Engine: After warming up
Keeping the engine speed between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute under no load
ON
Knock Sensor
INFOID:0000000011277838
The knock sensor is attached to the cylinder block. It senses engine
knocking using a piezoelectric element. A knocking vibration from
the cylinder block is sensed as vibrational pressure. This pressure is
converted into a voltage signal and sent to the ECM.
JSBIA0284ZZ
Revision: August 2014
EC-25
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Engine Oil Pressure Sensor
INFOID:0000000011277839
The engine oil pressure (EOP) sensor is detects engine oil pressure
and transmits a voltage signal to the ECM.
JSBIA0292ZZ
Engine Oil Temperature Sensor
INFOID:0000000011277840
The engine oil temperature sensor is used to detect the engine oil
temperature. The sensor modifies a voltage signal from the ECM.
The modified signal returns to the ECM as the engine oil temperature input. The sensor uses a thermistor which is sensitive to the
change in temperature. The electrical resistance of the thermistor
decreases as temperature increases.
JPBIA5280ZZ
<Reference data>
Engine oil temperature
[C (F)]
Voltage* (V)
Resistance (k)
10 (14)
4.4
7.0 - 11.4
20 (68)
3.5
2.37 - 2.63
50 (122)
2.2
0.68 - 1.00
90 (194)
1.0
0.236 - 0.260
110 (230)
0.6
0.143 - 0.153
SEF012P
*: These data are reference values and are measured between ECM terminals.
Cooling Fan
INFOID:0000000011277841
The ECM controls the cooling fan corresponding to the vehicle speed, engine coolant temperature, refrigerant
pressure, and air conditioner ON signal. The control system has 4-step control [HIGH/MIDDLE/LOW/OFF].
Cooling fan operates at each speed when the current flows in the cooling fan motor.
Refer to EC-48, "COOLING FAN CONTROL : System Description" for cooling fan operation.
Revision: August 2014
EC-26
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
EVAP Canister
INFOID:0000000011277842
EVAP canister stores the generated fuel vapors in the sealed fuel
tank to activated charcoals of EVAP canister when the engine is not
operating or when refueling to the fuel tank.
EC
D
JPBIA5851ZZ
EVAP Canister Purge Volume Control Solenoid Valve
INFOID:0000000011277843
The EVAP canister purge volume control solenoid valve uses a ON/
OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is
moved by ON/OFF pulses from the ECM. The longer the ON pulse,
the greater the amount of fuel vapor that will flow through the valve.
H
JMBIA0069ZZ
EVAP Canister Vent Control Valve
INFOID:0000000011277844
The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.
This solenoid valve responds to signals from the ECM. When the
ECM sends an ON signal, the coil in the solenoid valve is energized.
A plunger will then move to seal the canister vent. The ability to seal
the vent is necessary for the on board diagnosis of other evaporative
emission control system components.
This solenoid valve is used only for diagnosis, and usually remains
opened.
When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows EVAP
Control System diagnosis.
EVAP Control System Pressure Sensor
L
PBIB1263E
INFOID:0000000011277845
The EVAP control system pressure sensor detects pressure in the
purge line. The sensor output voltage to the ECM increases as pressure increases.
P
PBIB3370E
Revision: August 2014
EC-27
2015 Rogue NAM
COMPONENT PARTS
[QR25DE]
< SYSTEM DESCRIPTION >
Refrigerant Pressure Sensor
INFOID:0000000011277846
The refrigerant pressure sensor is installed at the condenser of the air conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
PBIB2657E
Stop Lamp Switch & Brake Pedal Position Switch
INFOID:0000000011277847
Stop lamp switch and brake pedal position switch are installed to brake pedal bracket.
ECM detects the state of the brake pedal by those two types of input (ON/OFF signal).
Brake pedal
Brake pedal position switch
Stop lamp switch
Released
ON
OFF
Depressed
OFF
ON
ASCD Steering Switch
INFOID:0000000011277848
ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation
of switch, and determines which button is operated.
Information Display
INFOID:0000000011277849
The operation mode of the ASCD is indicated on the information display in the combination meter.
ECM transmits the status signal to the combination meter via CAN communication according to ASCD operation.
Revision: August 2014
EC-28
2015 Rogue NAM
STRUCTURE AND OPERATION
[QR25DE]
< SYSTEM DESCRIPTION >
STRUCTURE AND OPERATION
Positive Crankcase Ventilation
INFOID:0000000011277850
EC
G
PBIB0492E
This system returns blow-by gas to the intake manifold.
The positive crankcase ventilation (PCV) valve is provided to conduct crankcase blow-by gas to the intake
manifold.
During partial throttle operation of the engine, the intake manifold sucks the blow-by gas through the PCV
valve.
Normally, the capacity of the valve is sufficient to handle any blow-by and a small amount of ventilating air.
The ventilating air is then drawn from the air inlet tubes into the crankcase. In this process the air passes
through the hose connecting air inlet tubes to rocker cover.
Under full-throttle condition, the manifold vacuum is insufficient to draw the blow-by flow through the valve.
The flow goes through the hose connection in the reverse direction.
On vehicles with an excessively high blow-by, the valve does not
meet the requirement. This is because some of the flow will go
through the hose connection to the air inlet tubes under all conditions.
M
PBIB1588E
Revision: August 2014
EC-29
2015 Rogue NAM
STRUCTURE AND OPERATION
[QR25DE]
< SYSTEM DESCRIPTION >
On Board Refueling Vapor Recovery (ORVR)
INFOID:0000000011277851
JMBIA1930GB
From the beginning of refueling, the air and vapor inside the fuel tank go through refueling EVAP vapor cut
valve and EVAP/ORVR line to the EVAP canister. The vapor is absorbed by the EVAP canister and the air is
released to the atmosphere.
When the refueling has reached the full level of the fuel tank, the refueling EVAP vapor cut valve is closed and
refueling is stopped because of auto shut-off. The vapor which was absorbed by the EVAP canister is purged
during driving.
WARNING:
When conducting inspections below, be sure to observe the following:
Put a CAUTION: FLAMMABLE sign in workshop.
Do not smoke while servicing fuel system. Keep open flames and sparks away from work area.
Be sure to furnish the workshop with a CO2 fire extinguisher.
CAUTION:
Before removing fuel line parts, carry out the following procedures:
- Put drained fuel in an explosion-proof container and put lid on securely.
- Release fuel pressure from fuel line. Refer to EC-147, "Work Procedure".
- Disconnect battery ground cable.
Always replace O-ring when the fuel gauge retainer is removed.
Do not kink or twist hose and tube when they are installed.
Do not tighten hose and clamps excessively to avoid damaging hoses.
After installation, run engine and check for fuel leaks at connection.
Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
Revision: August 2014
EC-30
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
SYSTEM
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM : System Description
INFOID:0000000011277852
EC
SYSTEM DIAGRAM
C
JSBIA4499GB
SYSTEM DESCRIPTION
Revision: August 2014
EC-31
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
ECM controls the engine by various functions.
Function
Reference
Multiport fuel injection system
EC-37, "MULTIPORT FUEL INJECTION SYSTEM : System Description (with automatic air conditioner)"
Electric ignition system
EC-41, "ELECTRIC IGNITION SYSTEM : System Description"
Intake valve timing control
EC-42, "INTAKE VALVE TIMING CONTROL : System Description"
Exhaust valve timing control
EC-45, "EXHAUST VALVE TIMING CONTROL : System Description"
Intake manifold runner control
EC-46, "INTAKE MANIFOLD RUNNER CONTROL : System Description"
Engine protection control
EC-46, "ENGINE PROTECTION CONTROL AT LOW ENGINE
OIL PRESSURE : System Description"
Fuel filler cap warning system
EC-50, "FUEL FILLER CAP WARNING SYSTEM : System Description"
Air conditioning cut control
EC-47, "AIR CONDITIONING CUT CONTROL : System Description"
Power generation voltage variable control
EC-47, "POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM : System Description"
Cooling fan control
EC-48, "COOLING FAN CONTROL : System Description"
Evaporative emission system
EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description"
Automatic speed control device (ASCD)
EC-49, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description"
CAN communication
EC-55, "CAN COMMUNICATION : System Description"
Sport mode
EC-56, "SPORT MODE CONTROL : System Description"
Revision: August 2014
EC-32
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
ENGINE CONTROL SYSTEM : Circuit Diagram
INFOID:0000000011518216
EC
JSBIA5685GB
Revision: August 2014
EC-33
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
JSBIA4979GB
ENGINE CONTROL SYSTEM : Fail Safe
INFOID:0000000011551458
NON DTC RELATED ITEM
Revision: August 2014
EC-34
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Detected
items
Engine operating condition
in fail-safe mode
Malfunction
indicator
lamp circuit
Engine speed will not rise
more than 2,500 rpm due
to the fuel cut
Remarks
Reference page
When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by lighting up MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating fail safe function.
The fail safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction.
EC
EC-479, "Component Function
Check"
DTC RELATED ITEM
Description
When a DTC is detected, ECM executes a mode (in the Fail-safe mode) applicable to the DTC. The fail-safe
mode has the preset traveling control mode (accelerator angle variation and engine output limit) and device fix
mode.
Fail safe mode
Traveling control mode
Vehicle behavior
Accelerator angle variation
control
ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Engine output
control
ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle
speed to encourage the driver to repair malfunction.
This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the reference position.
The intake manifold runner control valve motor is turned OFF (intake manifold runner control
valve opens).
Device fix mode
Fail Safe Pattern
J
Pattern
A
Fail safe mode
Accelerator angle variation control
Traveling control mode
B
C
Engine output control
Device fix mode
Fail Safe List
:Applicable : Not applicable
Vehicle behavior
DTC
No.
P0011
Detected items
Pattern
A
ECM activates the IVT intermediate lock control solenoid
valve to bring the cam sprocket into an intermediate lock condition.
Intake valve timing control
P0014
P0078
Exhaust valve timing control
P0101
P0102
P0103
Mass air flow sensor circuit
P0122
P0123
P0222
P0223
P2135
Throttle position sensor
Revision: August 2014
M
Others
EC-35
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Vehicle behavior
DTC
No.
Detected items
Pattern
Others
P0171
P0172
Fuel injection system
P0197
P0198
Engine oil temperature sensor
P0300
P0301
P0302
P0303
P0304
Misfire
P0500
Vehicle speed sensor
P050A
Cold start control
P0524
Engine oil pressure
P052A
P052B
Intake valve timing intermediate lock control
P0603
ECM
P0604
ECM
P0605
P060B
ECM
P0606
ECM
P0607
ECM
Exhaust valve timing control does not function.
ECM illuminates oil pressure warning lamp on the combination meter.
Engine speed will not rise more than 4,000rpm due to the
fuel cut.
Fail-safe is canceled when ignition switch OFF ON.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
P060A
ECM
P0643
ECM
P1078
Exhaust valve timing control
position sensor circuit
P1568
Signal invalid
P1805
Brake switch
Intake manifold runner control
valve
P2100
P2103
Throttle control motor relay
P2101
Electric throttle control function
Revision: August 2014
Active trace control does not function.
ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
P2004
ASCD operation may be deactivated.
Vehicle condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
EC-36
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Vehicle behavior
DTC
No.
P2118
Detected items
Pattern
A
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
EC
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
Throttle control motor
P2119
Electric throttle control actuator
P2122
P2123
P2127
P2128
P2138
Accelerator pedal position
sensor
A
Others
MULTIPORT FUEL INJECTION SYSTEM
MULTIPORT FUEL INJECTION SYSTEM : System Description (with automatic air
conditioner)
SYSTEM DIAGRAM
INFOID:0000000011277854
N
JPBIA5978GB
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). The amount of fuel injected is a program value in the
ECM memory. The program value is preset by engine operating conditions. These conditions are determined
by input signals (for engine speed and intake air) from the crankshaft position sensor (POS), camshaft position
sensor (PHASE) and the mass air flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compensated to improve engine performance under various operating conditions as listed below.
<Fuel increase>
During warm-up
Revision: August 2014
EC-37
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
When starting the engine
During acceleration
Hot-engine operation
When selector lever is changed from N to D
High-load, high-speed operation
<Fuel decrease>
During deceleration
During high engine speed operation
MIXTURE RATIO FEEDBACK CONTROL (CLOSED LOOP CONTROL)
PBIB2793E
The mixture ratio feedback system provides the best air-fuel mixture ratio for driveability and emission control.
The three way catalyst (manifold) can then better reduce CO, HC and NOx emissions. This system uses A/F
sensor 1 in the exhaust manifold to monitor whether the engine operation is rich or lean. The ECM adjusts the
injection pulse width according to the sensor voltage signal. For more information about A/F sensor 1, refer to
EC-24, "Air Fuel Ratio (A/F) Sensor 1". This maintains the mixture ratio within the range of stoichiometric
(ideal air-fuel mixture).
This stage is referred to as the closed loop control condition.
Heated oxygen sensor 2 is located downstream of the three way catalyst (manifold). Even if the switching
characteristics of A/F sensor 1 shift, the air-fuel ratio is controlled to stoichiometric by the signal from heated
oxygen sensor 2.
Open Loop Control
The open loop system condition refers to when the ECM detects any of the following conditions. Feedback
control stops in order to maintain stabilized fuel combustion.
- Deceleration and acceleration
- High-load, high-speed operation
- Malfunction of A/F sensor 1 or its circuit
- Insufficient activation of A/F sensor 1 at low engine coolant temperature
- High engine coolant temperature
- During warm-up
- After shifting from N to D
- When starting the engine
MIXTURE RATIO SELF-LEARNING CONTROL
The mixture ratio feedback control system monitors the mixture ratio signal transmitted from A/F sensor 1.
This feedback signal is then sent to the ECM. The ECM controls the basic mixture ratio as close to the theoretical mixture ratio as possible. However, the basic mixture ratio is not necessarily controlled as originally
designed. Both manufacturing differences (i.e., mass air flow sensor hot wire) and characteristic changes during operation (i.e., fuel injector clogging) directly affect mixture ratio.
Accordingly, the difference between the basic and theoretical mixture ratios is monitored in this system. This is
then computed in terms of injection pulse duration to automatically compensate for the difference between
the two ratios.
Fuel trim refers to the feedback compensation value compared against the basic injection duration. Fuel trim
includes short term fuel trim and long term fuel trim.
Short term fuel trim is the short-term fuel compensation used to maintain the mixture ratio at its theoretical
value. The signal from A/F sensor 1 indicates whether the mixture ratio is RICH or LEAN compared to the theoretical value. The signal then triggers a reduction in fuel volume if the mixture ratio is rich, and an increase in
fuel volume if it is lean.
Long term fuel trim is overall fuel compensation carried out long-term to compensate for continual deviation
of the short term fuel trim from the central value. Such deviation will occur due to individual engine differences,
wear over time and changes in the usage environment.
Revision: August 2014
EC-38
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
FUEL INJECTION TIMING
EC
C
SEF337W
Two types of systems are used.
Sequential Multiport Fuel Injection System
Fuel is injected into each cylinder during each engine cycle according to the firing order. This system is used
when the engine is running.
Simultaneous Multiport Fuel Injection System
Fuel is injected simultaneously into all four cylinders twice each engine cycle. In other words, pulse signals
of the same width are simultaneously transmitted from the ECM.
The four injectors will then receive the signals two times for each engine cycle.
This system is used when the engine is being started and/or if the fail-safe system (CPU) is operating.
FUEL SHUT-OFF
Fuel to each cylinder is cut off during deceleration, operation of the engine at excessively high speeds or operation of the vehicle at excessively high speeds.
MULTIPORT FUEL INJECTION SYSTEM : System Description (with manual air conditioner)
SYSTEM DIAGRAM
INFOID:0000000011277855
P
JPBIA6221GB
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). The amount of fuel injected is a program value in the
ECM memory. The program value is preset by engine operating conditions. These conditions are determined
Revision: August 2014
EC-39
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
by input signals (for engine speed and intake air) from the crankshaft position sensor (POS), camshaft position
sensor (PHASE) and the mass air flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compensated to improve engine performance under various operating conditions as listed below.
<Fuel increase>
During warm-up
When starting the engine
During acceleration
Hot-engine operation
When selector lever is changed from N to D
High-load, high-speed operation
<Fuel decrease>
During deceleration
During high engine speed operation
MIXTURE RATIO FEEDBACK CONTROL (CLOSED LOOP CONTROL)
PBIB2793E
The mixture ratio feedback system provides the best air-fuel mixture ratio for driveability and emission control.
The three way catalyst (manifold) can then better reduce CO, HC and NOx emissions. This system uses A/F
sensor 1 in the exhaust manifold to monitor whether the engine operation is rich or lean. The ECM adjusts the
injection pulse width according to the sensor voltage signal. For more information about A/F sensor 1, refer to
EC-24, "Air Fuel Ratio (A/F) Sensor 1". This maintains the mixture ratio within the range of stoichiometric
(ideal air-fuel mixture).
This stage is referred to as the closed loop control condition.
Heated oxygen sensor 2 is located downstream of the three way catalyst (manifold). Even if the switching
characteristics of A/F sensor 1 shift, the air-fuel ratio is controlled to stoichiometric by the signal from heated
oxygen sensor 2.
Open Loop Control
The open loop system condition refers to when the ECM detects any of the following conditions. Feedback
control stops in order to maintain stabilized fuel combustion.
- Deceleration and acceleration
- High-load, high-speed operation
- Malfunction of A/F sensor 1 or its circuit
- Insufficient activation of A/F sensor 1 at low engine coolant temperature
- High engine coolant temperature
- During warm-up
- After shifting from N to D
- When starting the engine
MIXTURE RATIO SELF-LEARNING CONTROL
The mixture ratio feedback control system monitors the mixture ratio signal transmitted from A/F sensor 1.
This feedback signal is then sent to the ECM. The ECM controls the basic mixture ratio as close to the theoretical mixture ratio as possible. However, the basic mixture ratio is not necessarily controlled as originally
designed. Both manufacturing differences (i.e., mass air flow sensor hot wire) and characteristic changes during operation (i.e., fuel injector clogging) directly affect mixture ratio.
Accordingly, the difference between the basic and theoretical mixture ratios is monitored in this system. This is
then computed in terms of injection pulse duration to automatically compensate for the difference between
the two ratios.
Fuel trim refers to the feedback compensation value compared against the basic injection duration. Fuel trim
includes short term fuel trim and long term fuel trim.
Revision: August 2014
EC-40
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Short term fuel trim is the short-term fuel compensation used to maintain the mixture ratio at its theoretical
value. The signal from A/F sensor 1 indicates whether the mixture ratio is RICH or LEAN compared to the the- A
oretical value. The signal then triggers a reduction in fuel volume if the mixture ratio is rich, and an increase in
fuel volume if it is lean.
Long term fuel trim is overall fuel compensation carried out long-term to compensate for continual deviation
EC
of the short term fuel trim from the central value. Such deviation will occur due to individual engine differences,
wear over time and changes in the usage environment.
FUEL INJECTION TIMING
SEF337W
Two types of systems are used.
Sequential Multiport Fuel Injection System
Fuel is injected into each cylinder during each engine cycle according to the firing order. This system is used
when the engine is running.
Simultaneous Multiport Fuel Injection System
Fuel is injected simultaneously into all four cylinders twice each engine cycle. In other words, pulse signals
of the same width are simultaneously transmitted from the ECM.
The four injectors will then receive the signals two times for each engine cycle.
This system is used when the engine is being started and/or if the fail-safe system (CPU) is operating.
FUEL SHUT-OFF
Fuel to each cylinder is cut off during deceleration, operation of the engine at excessively high speeds or operation of the vehicle at excessively high speeds.
ELECTRIC IGNITION SYSTEM
ELECTRIC IGNITION SYSTEM : System Description
INFOID:0000000011277856
SYSTEM DIAGRAM
P
JPBIA3193GB
SYSTEM DESCRIPTION
Firing order: 1 - 3 - 4 - 2
The ignition timing is controlled by the ECM to maintain the best air-fuel ratio for every running condition of the
engine. The ignition timing data is stored in the ECM.
Revision: August 2014
EC-41
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
The ECM receives information such as the injection pulse width and camshaft position sensor (PHASE) signal. Computing this information, ignition signals are transmitted to the power transistor.
During the following conditions, the ignition timing is revised by the ECM according to the other data stored in
the ECM.
At starting
During warm-up
At idle
At low battery voltage
During acceleration
The knock sensor retard system is designed only for emergencies. The basic ignition timing is programmed
within the anti-knocking zone, if recommended fuel is used under dry conditions. The retard system does not
operate under normal driving conditions. If engine knocking occurs, the knock sensor monitors the condition.
The signal is transmitted to the ECM. The ECM retards the ignition timing to eliminate the knocking condition.
INTAKE VALVE TIMING CONTROL
INTAKE VALVE TIMING CONTROL : System Description
INFOID:0000000011277857
INTAKE VALVE TIMING CONTROL
System Diagram
JMBIA1830GB
System Description
JPBIA6316GB
Revision: August 2014
EC-42
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake
valve.
A
The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant
temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing (IVT) control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake
EC
valve to increase engine torque in low/mid speed range and output in high-speed range.
INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL
C
System Diagram
H
JPBIA5973GB
System Description
The intake valve timing intermediate lock control improves the cleaning ability of exhaust gas at cold starting
by fixing the camshaft sprocket (INT) with two lock keys and bringing the cam phase into intermediate phase.
N
JPBIA6317GB
Cam phase is fixed at the intermediate phase by two lock keys in the camshaft sprocket (INT). Lock key 1 controls retard position and lock key 2 controls advance position.
ECM controls the intermediate phase lock by opening/closing the intake valve timing intermediate lock control
solenoid valve to control oil pressure acting on the lock key and locking/unlocking the lock key.
Lock/Unlock Activation
When ECM activates the intake valve timing intermediate lock control solenoid valve, oil pressure generated in
the oil pump is drained through the oil pressure path in the control valve. Since oil pressure is not acted on the
lock key, the lock key position is fixed by the spring tension and the cam phase is fixed at the intermediate
phase.
When ECM deactivates the intake valve timing intermediate lock control solenoid valve, unlocking oil pressure
acts on each lock key. Lock key 1 is not released because it is under load due to sprocket rotational force. For
Revision: August 2014
EC-43
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
this reason, lock key 2 is released first by being pushed up by unlocking oil pressure. When lock key 2 is
released, some clearance is formed between lock key 1 and the rotor due to sprocket rotational force and
return spring force. Accordingly, lock key 1 is pushed up by unlocking oil pressure and the intermediated
phase lock is released.
JPBIA5970GB
When stopping the engine
When the ignition switch is turned from idle state to OFF, ECM receives an ignition switch signal from BCM via
CAN communication and activates the intake valve timing intermediate lock control solenoid valve and drains
oil pressure acting on the lock key before activating the intake valve timing control solenoid valve and operating the cam phase toward the advance position.
The cam phase is fixed by the lock key when shifting to the intermediated phase and ECM performs Lock
judgment to stop the engine.
When starting the engine
When starting the engine by cold start, ECM judges the locked/unlocked state when ignition switch is turned
ON. When judged as locked state (fixed at the intermediate phase), the intake valve timing intermediate lock
control solenoid valve is activated. Since oil pressure does not act on the lock key even when the engine is
started, the cam phase is fixed at the intermediate phase and the intake valve timing control is not performed.
When the engine stops without locking the cam phase at the intermediate phase due to an engine stall and the
state is not judged as locked, the intake valve timing intermediate lock control solenoid valve and the intake
valve timing control solenoid valve are activated and the cam phase shifts to the advanced position to be
locked at the intermediate phase. Even when not locked in the intermediate lock phase due to no oil pressure
or low oil pressure, a ratchet structure of the camshaft sprocket (INT) rotor allows the conversion to the intermediate phase in stages by engine vibration.
When engine coolant temperature is more than 60C, the intake valve timing is controlled by deactivating the
intake valve timing intermediate lock control solenoid valve and releasing the intermediate phase lock.
When the engine is started after warming up, ECM releases the intermediate phase lock immediately after the
engine start and controls the intake valve timing.
EXHAUST VALVE TIMING CONTROL
Revision: August 2014
EC-44
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
EXHAUST VALVE TIMING CONTROL : System Description
INFOID:0000000011277858
SYSTEM DIAGRAM
EC
JPBIA4761GB
SYSTEM DESCRIPTION
G
JPBIA5972GB
This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the exhaust
valve.
The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine oil temperature. Then, the ECM sends ON/OFF pulse duty signals to the exhaust valve timing (EVT) control solenoid
valve depending on driving status. This makes it possible to control the shut/open timing of the exhaust valve
to increase engine torque and output in a range of high engine speed.
INTAKE MANIFOLD RUNNER CONTROL
Revision: August 2014
EC-45
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
INTAKE MANIFOLD RUNNER CONTROL : System Description
INFOID:0000000011277859
SYSTEM DIAGRAM
JPBIA6226GB
SYSTEM DESCRIPTION
Intake manifold runner control valve has a valve portion in the intake passage of each cylinder.
While idling and during low engine coolant temperature, the intake manifold runner control valve closes. Thus
the velocity of the air in the intake passage increases, promoting the vaporization of the fuel and producing a
intake manifold runner in the combustion chamber.
Because of this operation, this system tends to increase the burning speed of the gas mixture, improve
exhaust emission, and increase the stability in running conditions.
Also, except when idling and during low engine coolant temperature, this system opens the intake manifold
runner control valve.
In this condition, this system tends to increase power by improving intake efficiency via reduction of intake flow
resistance.
The intake manifold runner control valve is operated by the ECM.
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE : System Description
INFOID:0000000011277860
SYSTEM DIAGRAM
JSBIA4201GB
SYSTEM DESCRIPTION
The engine protection control at low engine oil pressure warns the driver of a decrease in engine oil pressure by the engine oil pressure warning lamp a before the engine becomes damaged.
When detecting a decrease in engine oil pressure at an engine speed less than 1,000 rpm, ECM transmits
an engine oil pressure warning lamp signal to the combination meter.The combination meter turns ON the
engine oil pressure warning lamp, according to the signal.
Combination meter
Decrease in engine oil pressure
Detection
Engine speed
Engine oil pressure warning
lamp
Fuel cut
Less than 1,000 rpm
ON*
NO
1,000 rpm or more
ON
YES
*: When detecting a normal engine oil pressure, ECM turns OFF the engine oil pressure warning lamp.
AIR CONDITIONING CUT CONTROL
Revision: August 2014
EC-46
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
AIR CONDITIONING CUT CONTROL : System Description
INFOID:0000000011277861
SYSTEM DIAGRAM
EC
JSBIA4542GB
SYSTEM DESCRIPTION
This system improves engine operation when the air conditioner is used.
Under the following conditions, the air conditioner is turned off.
When cranking the engine.
At high engine speeds.
When the engine coolant temperature becomes excessively high.
When operating power steering during low engine speed or low vehicle speed.
When engine speed is excessively low.
When refrigerant pressure is excessively low or high.
POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM
POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM : System Description
INFOID:0000000011277862
DESCRIPTION
ECM transmits a target power generation voltage signal received from IPDM E/R to the generator via LIN
communication.
The generator includes a self-diagnosis function and transmits a diagnosis signal to ECM via LIN communication when detecting a malfunction. When ECM receives a diagnosis signal, ECM detects DTC and transmits a
charge warning lamp request signal to the combination meter to turn ON the charge warning lamp.
COOLING FAN CONTROL
Revision: August 2014
EC-47
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
COOLING FAN CONTROL : System Description
INFOID:0000000011277863
SYSTEM DIAGRAM
JPBIA3233GB
SYSTEM DESCRIPTION
ECM controls cooling fan speed corresponding to vehicle speed, engine coolant temperature, refrigerant pressure, air conditioner ON signal. Then control system has 3-step control [HIGH/LOW/OFF].
Cooling Fan Operation
JSBIA4541GB
Cooling Fan Relay Operation
The ECM controls cooling fan relays through CAN communication line.
Cooling fan speed
Stop (OFF)
Revision: August 2014
Cooling fan relay
1
OFF
OFF
OFF
EC-48
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Cooling fan speed
Cooling fan relay
1
Low (LOW)
OFF
ON
OFF
High (HI)
ON
OFF
ON
EC
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description
INFOID:0000000011277864
SYSTEM DIAGRAM
D
JPBIA3210GB
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
The ASCD operation status is indicated by two indicators (CRUISE and SET on the information display) on the
combination meter. If any malfunction occurs in ASCD system, SET indicator blinks and ASCD control is deactivated.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (CRUISE is indicated on the information display.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET is indicated on the information display.)
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
CANCEL switch is pressed
More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)
Brake pedal is depressed
Selector lever is changed to N, P, R position
Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
TCS system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicators.
Revision: August 2014
EC-49
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE indicator may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE indicator will
stop blinking and the cruise operation will be able to work by pressing SET/COAST switch or RESUME/
ACCELERATE switch.
Malfunction for some self-diagnoses regarding ASCD control: SET indicator will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is pressed after cancel operation other than pressing MAIN switch
is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition must
meet following conditions.
Brake pedal is released
Selector lever is in other than P and N positions
Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
FUEL FILLER CAP WARNING SYSTEM
FUEL FILLER CAP WARNING SYSTEM : System Description
INFOID:0000000011277865
SYSTEM DIAGRAM
JSBIA0797GB
SYSTEM DESCRIPTION
The fuel filler cap warning system alerts the driver to the prevention of the fuel filler being left uncapped and
malfunction occurrences after refueling, by turning ON the fuel filler cap warning display on the combination
meter.
ECM judges a refueled state, based on a fuel level signal transmitted from the combination meter.
When a very small leak is detected through the EVAP leak diagnosis performed after judging the refueled
state, ECM transmits a fuel filler cap warning display signal (request for display ON) to the combination meter
via CAN communication.
When receiving the signal, the combination meter turns ON the fuel filler cap warning display.
CAUTION:
Check fuel filler cap installation condition when the fuel filler cap warning display turns ON.
Reset Operation
The fuel filler cap warning lamp tunes OFF, according to any condition listed below:
Reset operation is performed by operating the meter control switch on the combination meter. Refer to MWI18, "Switch Name and Function".
- When the reset operation is performed, the combination meter transmits a fuel filler cap warning reset signal
to ECM via CAN communication. ECM transmits a fuel filler cap warning display signal (request for display
Revision: August 2014
EC-50
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
OFF) to the combination meter via CAN communication. When receiving the signal, the combination meter
turns OFF the fuel filler cap warning display.
A
EVAP leak diagnosis result is normal.
Fuel refilled.
DTC erased by using CONSULT.
EC
NOTE:
MIL turns ON if a malfunction is detected in leak diagnosis results again at the trip after the fuel filler cap warning display turns ON/OFF.
WARNING/INDICATOR/CHIME LIST
WARNING/INDICATOR/CHIME LIST : Warning lamps/Indicator lamps
INFOID:0000000011277866
D
Name
Malfunction indicator lamp (MIL)
Arrangement/Function
Regarding the function. Refer to EC-51, "WARNING/INDICATOR/CHIME LIST : Malfunction Indicator Lamp (MIL)".
WARNING/INDICATOR/CHIME LIST : Warning/Indicator (On Information Display)
INFOID:0000000011277867
WARNING
G
Name
Arrangement/Function
Engine oil pressure warning
Regarding the function. Refer to EC-53, "WARNING/INDICATOR/CHIME LIST : Engine Oil Pressure Warning".
Fuel filler cap warning
Regarding the function. Refer to EC-54, "WARNING/INDICATOR/CHIME LIST : Fuel
Filler Cap Warning".
INDICATOR/INFORMATION
Name
Design
Function
K
CRUISE indicator
EC-49, "AUTOMATIC SPEED CONTROL DEVICE
(ASCD) : System Description"
SET indicator
M
JSBIA3459ZZ
WARNING/INDICATOR/CHIME LIST : Malfunction Indicator Lamp (MIL)
INFOID:0000000011277868
DESIGN/PURPOSE
When a malfunction which increases exhaust gases is detected, ECM turns ON MIL and informs the driver of
the necessity of inspection and repair.
Revision: August 2014
EC-51
2015 Rogue NAM
SYSTEM
< SYSTEM DESCRIPTION >
When a malfunction which causes damage to the catalyst is
detected, ECM immediately blinks MIL to alert the driver.
[QR25DE]
SAT652J
BULB CHECK
The bulb turns ON after turning ON the ignition switch (engine stop) and turns OFF after restarting the engine.
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL
For the operation for CAN communication blackout in the combination meter, refer to MWI-30, "Fail-safe".
SYSTEM DIAGRAM
JSBIA4500GB
SIGNAL PATH
When the lighting conditions of the malfunction indicator lamp (MIL) are satisfied, ECM transmits a malfunction indicator lamp (MIL) signal to the combination meter via CAN communication.
The combination meter turns ON or blinks the malfunction indicator lamp (MIL), according to a signal
received from ECM.
LIGHTING CONDITION
When all of the following conditions are satisfied:
Ignition switch: ON
DTC which influences on exhaust gasses is judged.
For DTCs that the malfunction indicator lamp turns ON and the number of DTC diagnosis trips, refer to EC-96,
"DTC Index".
SHUTOFF CONDITION
When any of the following conditions is satisfied:
Ignition switch: OFF
Erase DTC
NOTE:
For the conditions of erasing DTC, refer to EC-59, "DIAGNOSIS DESCRIPTION : DTC and Freeze Frame
Data".
Revision: August 2014
EC-52
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
TIMING CHART
EC
E
JPBIA6022GB
WARNING/INDICATOR/CHIME LIST : Engine Oil Pressure Warning
INFOID:0000000011277869
DESIGN/PURPOSE
When engine oil pressure is low, the engine oil pressure warning informs the driver of low oil pressure to prevent damage to the engine.
Symbol
Message
I
Low oil pressure: See owners Manual
K
JPNIA1881ZZ
BULB CHECK
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL
For the operation for CAN communications blackout or abnormal signal reception, refer to MWI-30, "Fail-safe".
SYSTEM DIAGRAM
N
P
JSBIA3494GB
SIGNAL PATH
ECM calculates an engine oil pressure according to a signal transmitted from the engine oil pressure sensor.
After engine running when the engine oil pressure is low and at least 5 seconds, ECM transmits the engine oil
Revision: August 2014
EC-53
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
pressure warning signal to combination meter via CAN communication. Then the engine oil pressure warning
displays.
LIGHTING CONDITION
When all of the following conditions for at least 5 seconds are satisfied:
Ignition switch: ON
Engine oil pressure is less than specified value.
Engine speed is more than 500 rpm.
SHUTOFF CONDITION
When any of the following conditions is satisfied:
Ignition switch: OFF
Engine oil pressure is the specified value or more.
Engine speed is less than 500 rpm.
TIMING CHART
JSBIA3495GB
WARNING/INDICATOR/CHIME LIST : Fuel Filler Cap Warning
INFOID:0000000011277870
DESIGN/PURPOSE
Warn the driver that the fuel filler cap is left opened.
Symbol
Message
Loose Fuel Cap
JSBIA3176GB
For detailes, refer to EC-50, "FUEL FILLER CAP WARNING SYSTEM : System Description".
EVAPORATIVE EMISSION SYSTEM
Revision: August 2014
EC-54
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
EVAPORATIVE EMISSION SYSTEM : System Description
INFOID:0000000011277871
SYSTEM DIAGRAM
EC
F
JSBIA0371GB
SYSTEM DESCRIPTION
L
PBIB1631E
The evaporative emission system is used to reduce hydrocarbons emitted into the atmosphere from the fuel
system. This reduction of hydrocarbons is accomplished by activated charcoals in the EVAP canister.
The fuel vapor in the sealed fuel tank is led into the EVAP canister which contains activated carbon and the
vapor is stored there when the engine is not operating or when refueling to the fuel tank.
The vapor in the EVAP canister is purged by the air through the purge line to the intake manifold when the
engine is operating. EVAP canister purge volume control solenoid valve is controlled by ECM. When the
engine operates, the flow rate of vapor controlled by EVAP canister purge volume control solenoid valve is
proportionally regulated as the air flow increases.
EVAP canister purge volume control solenoid valve also shuts off the vapor purge line during decelerating.
CAN COMMUNICATION
CAN COMMUNICATION : System Description
INFOID:0000000011277872
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Revision: August 2014
EC-55
2015 Rogue NAM
SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
Refer to LAN-32, "CAN COMMUNICATION SYSTEM : CAN Communication Signal Chart", about CAN communication for detail.
SPORT MODE CONTROL
SPORT MODE CONTROL : System Description
INFOID:0000000011277873
SYSTEM DIAGRAM
JSBIA3227GB
SYSTEM DESCRIPTION
SPORT mode that keeps high engine revolution and provides direct feel and acceleration performance suitable for driving on winding road.
ECM receives an SPORT mode signal from TCM via CAN communication and improves drivability by controlling the throttle movement.
ECM transmits an SPORT mode indicator lamp signal to the combination meter via CAN communication.
NOTE:
For the details of the SPORT mode, refer to DMS-8, "SPORT MODE CONTROL : System Description".
ECO MODE CONTROL
ECO MODE CONTROL : System Description
INFOID:0000000011518220
SYSTEM DESCRIPTION
ECM receives an ECO mode signal from TCM via CAN communication and improves the fuel economy by
controlling the throttle movement to less than usual.
For details of ECO mode system, refer to TM-43, "ECO MODE SYSTEM : System Description".
Revision: August 2014
EC-56
2015 Rogue NAM
OPERATION
[QR25DE]
< SYSTEM DESCRIPTION >
OPERATION
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function
INFOID:0000000011277874
EC
SWITCHES AND INDICATORS
C
JPBIA5872ZZ
On the combination meter
On the steering wheel
CRUISE indicator
SET indicator
CANCEL switch
ACCEL/RES switch
COAST/SET switch
ASCD MAIN switch
SET SPEED RANGE
ASCD system can be set the following vehicle speed.
Minimum speed (Approx.)
40 km/h (25 MPH)
Maximum speed (Approx.)
144 km/h (90 MPH)
SWITCH OPERATION
Item
Function
CANCEL switch
Cancels the cruise control driving.
ACCEL/RES switch
Resumes the set speed.
Increases speed incrementally during cruise control driving.
COAST/SET switch
Sets desired cruise speed.
Decreases speed incrementally during cruise control driving.
ASCD MAIN switch
Master switch to activate the ASCD system.
Refer to EC-49, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description" for ASCD operating
instructions.
Revision: August 2014
EC-57
2015 Rogue NAM
ON BOARD DIAGNOSTIC (OBD) SYSTEM
[QR25DE]
< SYSTEM DESCRIPTION >
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Diagnosis Description
INFOID:0000000011277875
This system is an on board diagnostic system that records exhaust emission-related diagnostic information
and detects a sensors/actuator-related malfunction. A malfunction is indicated by the malfunction indicator
lamp (MIL) and stored in control module memory as a DTC. The diagnostic information can be obtained with
the diagnostic tool (GST: Generic Scan Tool).
GST (Generic Scan Tool)
INFOID:0000000011277876
When GST is connected with a data link connector equipped on the vehicle side, it will communicate with the
control module equipped in the vehicle and then enable various kinds of diagnostic tests. Refer to EC-58,
"Diagnosis Description".
NOTE:
Service $0A is not applied for regions where it is not mandated.
Revision: August 2014
EC-58
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (ECM)
DIAGNOSIS DESCRIPTION
DIAGNOSIS DESCRIPTION : 1st Trip Detection Logic and Two Trip Detection Logic
INFOID:0000000011277877
When a malfunction is detected for the first time, 1st trip DTC and 1st trip Freeze Frame data are stored in the
ECM memory. The MIL will not illuminate at this stage. <1st trip>
If the same malfunction is detected again during the next drive, the DTC and Freeze Frame data are stored in
the ECM memory, and the MIL illuminates. The MIL illuminates at the same time when the DTC is stored.
<2nd trip> The trip in the Two Trip Detection Logic means a driving mode in which self-diagnosis is performed during vehicle operation. Specific on board diagnostic items will cause the ECM to illuminate or blink
the MIL, and store DTC and Freeze Frame data, even in the 1st trip, as shown below.
EC
: Applicable : Not applicable
MIL
DTC
1st trip
Items
2nd trip
1st trip DTC
1st trip
displaying
2nd trip
displaying
1st trip
displaying
2nd trip
displaying
Blinking
Illuminated
Blinking
Illuminated
Misfire (Possible three way catalyst
damage) DTC: P0300 P0304
is being detected
Misfire (Possible three way catalyst
damage) DTC: P0300 P0304
is being detected
One trip detection diagnoses (Refer to EC-96, "DTC Index".)
Except above
DIAGNOSIS DESCRIPTION : DTC and Freeze Frame Data
INFOID:0000000011277878
DTC AND 1ST TRIP DTC
The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not recur, the 1st trip DTC
will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is saved in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are saved in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two consecutive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd
trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL during the
1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
For malfunctions in which 1st trip DTCs are displayed, refer to EC-96, "DTC Index". These items are required
by legal regulations to continuously monitor the system/component. In addition, the items monitored non-continuously are also displayed on CONSULT.
1st trip DTC is specified in Service $07 of SAE J1979/ISO 15031-5. 1st trip DTC detection occurs without illuminating the MIL and therefore does not warn the driver of a malfunction.
When a 1st trip DTC is detected, check, print out or write down and erase (1st trip) DTC and Freeze Frame
data as specified in Work Flow procedure Step 2, refer to EC-130, "Work Flow". Then perform DTC Confirmation Procedure or Component Function Check to try to duplicate the malfunction. If the malfunction is duplicated, the item requires repair.
FREEZE FRAME DATA AND 1ST TRIP FREEZE FRAME DATA
The ECM records the driving conditions such as fuel system status, calculated load value, engine coolant temperature, short term fuel trim, long term fuel trim, engine speed, vehicle speed, absolute throttle position, base
fuel schedule and intake air temperature at the moment a malfunction is detected.
Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data.
The data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT or
GST. The 1st trip freeze frame data can only be displayed on the CONSULT screen.
Revision: August 2014
EC-59
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Only one set of freeze frame data (either 1st trip freeze frame data or freeze frame data) can be stored in the
ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority
for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once
freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no
longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the following priorities to update the data.
Priority
1
Items
Freeze frame data
2
3
Misfire DTC: P0300 P0304
Fuel Injection System Function DTC: P0171, P0172
Except the above items
1st trip freeze frame data
For example, the EGR malfunction (Priority: 2) was detected and the freeze frame data was saved in the 2nd
trip. After that when the misfire (Priority: 1) is detected in another trip, the freeze frame data will be updated
from the EGR malfunction to the misfire. The 1st trip freeze frame data is updated each time a different malfunction is detected. There is no priority for 1st trip freeze frame data. However, once freeze frame data is
stored in the ECM memory, 1st trip freeze data is no longer stored (because only one freeze frame data or 1st
trip freeze frame data can be stored in the ECM). If freeze frame data is stored in the ECM memory and freeze
frame data with the same priority occurs later, the first (original) freeze frame data remains unchanged in the
ECM memory.
Both 1st trip freeze frame data and freeze frame data (along with the DTCs) are cleared when the ECM memory is erased.
DIAGNOSIS DESCRIPTION : Counter System
INFOID:0000000011277879
RELATIONSHIP BETWEEN MIL, 1ST TRIP DTC, DTC, AND DETECTABLE ITEMS
When a malfunction is detected for the first time, the 1st trip DTC and the 1st trip freeze frame data are
stored in the ECM memory.
When the same malfunction is detected in two consecutive trips, the DTC and the freeze frame data are
stored in the ECM memory, and the MIL will come on.
The MIL will turn OFF after the vehicle is driven 3 times (driving pattern B) with no malfunction. The drive is
counted only when the recorded driving pattern is met (as stored in the ECM). If another malfunction occurs
while counting, the counter will reset.
The DTC and the freeze frame data will be stored until the vehicle is driven 40 times (driving pattern A) without the same malfunction recurring (except for Misfire and Fuel Injection System). For Misfire and Fuel Injection System, the DTC and freeze frame data will be stored until the vehicle is driven 80 times (driving pattern
C) without the same malfunction recurring. The TIME in SELF-DIAGNOSTIC RESULTS mode of CONSULT will count the number of times the vehicle is driven.
The 1st trip DTC is not displayed when the self-diagnosis results in OK for the 2nd trip.
COUNTER SYSTEM CHART
Items
MIL (turns OFF)
DTC, Freeze Frame Data (no display)
1st Trip DTC (clear)
1st Trip Freeze Frame Data (clear)
Fuel Injection System
Misfire
Other
3 (pattern B)
3 (pattern B)
3 (pattern B)
80 (pattern C)
80 (pattern C)
40 (pattern A)
1 (pattern C), *1
1 (pattern C), *1
1 (pattern B)
*1, *2
*1, *2
1 (pattern B)
For details about patterns B and C under Fuel Injection System and Misfire, see EXPLANATION FOR
DRIVING PATTERNS FOR MISFIRE <EXHAUST QUALITY DETERIORATION>, FUEL INJECTION SYSTEM.
For details about patterns A and B under Other, see EXPLANATION FOR DRIVING PATTERNS FOR MISFIRE <EXHAUST QUALITY DETERIORATION>, FUEL INJECTION SYSTEM.
*1: Clear timing is at the moment OK is detected.
*2: Clear timing is when the same malfunction is detected in the 2nd trip.
Relationship Between MIL, DTC, 1st Trip DTC and Driving Patterns for Misfire <Exhaust Quality Deterioration>, Fuel Injection System
Revision: August 2014
EC-60
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
EC
L
JMBIA1417GB
*1: When the same malfunction is detected in two consecutive trips, MIL
will light up.
*2: MIL will turn OFF after vehicle is driv- *3: When the same malfunction is deen 3 times (pattern B) without any
tected in two consecutive trips, the
malfunctions.
DTC and the freeze frame data will be
stored in ECM.
*4: The DTC and the freeze frame data *5: When a malfunction is detected for
*6: The 1st trip DTC and the 1st trip
will not be displayed any longer after
the first time, the 1st trip DTC and the
freeze frame data will be cleared at
vehicle is driven 80 times (pattern C)
1st trip freeze frame data will be
the moment OK is detected.
without the same malfunction. (The
stored in ECM.
DTC and the freeze frame data still
remain in ECM.)
*7: When the same malfunction is detected in the 2nd trip, the 1st trip
freeze frame data will be cleared.
*8: 1st trip DTC will be cleared when vehicle is driven once (pattern C) without the same malfunction after DTC
is stored in ECM.
Driving Pattern B
Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
EC-61
Explanation for Driving Patterns for Misfire <Exhaust Quality Deterioration>, Fuel Injection System
Revision: August 2014
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Driving Pattern C
Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
Example:
If the stored freeze frame data is as per the following:
Engine speed: 850 rpm, Calculated load value: 30%, Engine coolant temperature: 80C (176F)
To be satisfied with driving pattern C, the vehicle should run under the following conditions:
Engine speed: 475 1,225 rpm, Calculated load value: 27 33%, Engine coolant temperature: more than
70C (158F)
Relationship Between MIL, DTC, 1st Trip DTC and Driving Patterns Except For Misfire <Exhaust
Quality Deterioration>, Fuel Injection System
JMBIA1418GB
Revision: August 2014
EC-62
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
*1: When the same malfunction is detected in two consecutive trips, MIL
will light up.
*2: MIL will turn OFF after vehicle is driv- *3: When the same malfunction is deen 3 times (pattern B) without any
tected in two consecutive trips, the
malfunctions.
DTC and the freeze frame data will be
stored in ECM.
*4: The DTC and the freeze frame data
will not be displayed any longer after
vehicle is driven 40 times (pattern A)
without the same malfunction.
(The DTC and the freeze frame data
still remain in ECM.)
*5: When a malfunction is detected for
*6: 1st trip DTC will be cleared after vehithe first time, the 1st trip DTC and the
cle is driven once (pattern B) without
1st trip freeze frame data will be
the same malfunction.
stored in ECM.
EC
*7: When the same malfunction is detected in the 2nd trip, the 1st trip
freeze frame data will be cleared.
Explanation for Driving Patterns Except for Misfire <Exhaust Quality Deterioration>, Fuel Injection
System
Driving Pattern A
Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
Driving Pattern B
Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
DIAGNOSIS DESCRIPTION : Driving Pattern
INFOID:0000000011277880
CAUTION:
Always drive at a safe speed.
DRIVING PATTERN A
Driving pattern A means a trip satisfying the following conditions.
Engine speed reaches 400 rpm or more.
Engine coolant temperature rises by 20C (36F) or more after starting the engine.
Engine coolant temperature reaches 70C (158F) or more.
The ignition switch is turned from ON to OFF.
NOTE:
When the same malfunction is detected regardless of driving conditions, reset the counter of driving pattern
A.
When the above conditions are satisfied without detecting the same malfunction, reset the counter of driving
pattern A.
DRIVING PATTERN B
Driving pattern B means a trip satisfying the following conditions.
Engine speed reaches 400 rpm or more.
Engine coolant temperature reaches 70C (158F) or more.
Vehicle speed of 70 120 km/h (44 75 MPH) is maintained for 60 seconds or more under the control of
closed loop.
Vehicle speed of 30 60 km/h (19 37 MPH) is maintained for 10 seconds or more under the control of
closed loop.
Under the closed loop control condition, the following state reaches 12 seconds or more in total: Vehicle
speed of 4 km/h (2 MPH) or less with idling condition.
The state of driving at 10 km/h (7 MPH) or more reaches 10 minutes or more in total.
A lapse of 22 minutes or more after engine start.
NOTE:
Drive the vehicle at a constant velocity.
When the same malfunction is detected regardless of driving conditions, reset the counter of driving pattern
B.
When the above conditions are satisfied without detecting the same malfunction, reset the counter of driving
pattern B.
DRIVING PATTERN C
Driving pattern C means operating vehicle as per the following:
The following conditions should be satisfied at the same time:
Engine speed: (Engine speed in the freeze frame data) 375 rpm
Revision: August 2014
EC-63
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Calculated load value: (Calculated load value in the freeze frame data) x (10.1) [%]
Engine coolant temperature condition:
When the freeze frame data shows lower than 70C (158F), engine coolant temperature should be lower
than 70C (158F).
When the freeze frame data shows higher than or equal to 70C (158F), engine coolant temperature should
be higher than or equal to 70C (158F).
NOTE:
When the same malfunction is detected regardless of the above vehicle conditions, reset the counter of driving pattern C.
When the above conditions are satisfied without detecting the same malfunction, reset the counter of driving
pattern C.
The 1st trip DTC will be cleared when C counter is counted once without the same malfunction after DTC is
stored in ECM.
DRIVING PATTERN D
Driving pattern D means a trip satisfying the following conditions.
The state of driving at 40 km/h (25 MPH) reaches 300 seconds or more in total.
Idle speed lasts 30 seconds or more.
A lapse of 600 seconds or more after engine start.
NOTE:
When the same malfunction is detected regardless of driving conditions, reset the counter of driving pattern
D.
When the above conditions are satisfied without detecting the same malfunction, reset the counter of driving
pattern D.
DIAGNOSIS DESCRIPTION : System Readiness Test (SRT) Code
INFOID:0000000011277881
System Readiness Test (SRT) code is specified in Service $01 of SAE J1979/ISO 15031-5.
As part of an enhanced emissions test for Inspection & Maintenance (I/M), certain states require the status of
SRT be used to indicate whether the ECM has completed self-diagnosis of major emission systems and components. Completion must be verified in order for the emissions inspection to proceed.
If a vehicle is rejected for a State emissions inspection due to one or more SRT items indicating INCMP, use
the information in this Service Manual to set the SRT to CMPLT.
In most cases the ECM will automatically complete its self-diagnosis cycle during normal usage, and the SRT
status will indicate CMPLT for each application system. Once set as CMPLT, the SRT status remains
CMPLT until the self-diagnosis memory is erased.
Occasionally, certain portions of the self-diagnostic test may not be completed as a result of the customer's
normal driving pattern; the SRT will indicate INCMP for these items.
NOTE:
The SRT will also indicate INCMP if the self-diagnosis memory is erased for any reason or if the ECM memory power supply is interrupted for several hours.
If, during the state emissions inspection, the SRT indicates CMPLT for all test items, the inspector will continue with the emissions test. However, if the SRT indicates INCMP for one or more of the SRT items the
vehicle is returned to the customer untested.
NOTE:
If permanent DTC is stored or MIL illuminates during the state emissions inspection, the vehicle is also
returned to the customer untested even though the SRT indicates CMPLT for all test items. therefore, it is
important to check SRT (CMPLT), DTC (No DTCs) and permanent DTC (No permanent DTC) before the
inspection.
SRT SET TIMING
SRT is set as CMPLT after self-diagnosis has been performed one or more times. Completion of SRT is
done regardless of whether the result is OK or NG. The set timing is different between OK and NG results and
is shown in the table below.
Revision: August 2014
EC-64
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Example
Self-diagnosis result
All OK
Case 1
Case 2
NG exists
Case 3
Diagnosis
ON
OFF
Ignition cycle
ON OFF ON
OFF
ON
P0400
OK (1)
(1)
OK (2)
(2)
P0402
OK (1)
(1)
(1)
OK (2)
P1402
OK (1)
OK (2)
(2)
(2)
SRT of EGR
CMPLT
CMPLT
CMPLT
CMPLT
P0400
OK (1)
(1)
(1)
(1)
P0402
(0)
(0)
OK (1)
(1)
P1402
OK (1)
OK (2)
(2)
(2)
SRT of EGR
INCMP
INCMP
CMPLT
CMPLT
P0400
OK
OK
P0402
P1402
NG
NG
NG
(Consecutive
NG)
(1st trip)
DTC
1st trip DTC
1st trip DTC
DTC
(= MIL ON)
SRT of EGR
INCMP
INCMP
INCMP
CMPLT
OK: Self-diagnosis is carried out and the result is OK.
EC
NG: Self-diagnosis is carried out and the result is NG.
: Self-diagnosis is not carried out.
When all SRT related self-diagnoses show OK results in a single cycle (Ignition OFF-ON-OFF), the SRT will
indicate CMPLT. Case 1 above
When all SRT related self-diagnoses show OK results through several different cycles, the SRT will indicate
CMPLT at the time the respective self-diagnoses have at least one OK result. Case 2 above
If one or more SRT related self-diagnoses show NG results in 2 consecutive cycles, the SRT will also indicate
CMPLT. Case 3 above
The table above shows that the minimum number of cycles for setting SRT as INCMP is the number one (1)
for each self-diagnosis (Case 1 & 2) or the number two (2) for one of self-diagnoses (Case 3). However, in
preparation for the state emissions inspection, it is unnecessary for each self-diagnosis to be executed twice
(Case 3) for the following reasons:
The SRT will indicate CMPLT at the time the respective self-diagnoses have one (1) OK result.
The emissions inspection requires CMPLT of the SRT only with OK self-diagnosis results.
During SRT driving pattern, the 1st trip DTC (NG) is detected prior to CMPLT of SRT and the self-diagnosis
memory must be erased from the ECM after repair.
If the 1st trip DTC is erased, all the SRT will indicate INCMP.
NOTE:
SRT can be set as CMPLT together with the DTC(s). Therefore, DTC check must always be carried out
prior to the state emission inspection even though the SRT indicates CMPLT.
DIAGNOSIS DESCRIPTION : Permanent Diagnostic Trouble Code (Permanent DTC)
INFOID:0000000011277882
Permanent DTC is defined in SAE J1979/ISO 15031-5 Service $0A.
ECM stores a DTC issuing a command of turning on MIL as a permanent DTC and keeps storing the DTC as
a permanent DTC until ECM judges that there is no presence of malfunction.
Permanent DTCs cannot be erased by using the erase function of CONSULT or Generic Scan Tool (GST) and
by disconnecting the battery to shut off power to ECM. This prevents a vehicle from passing the in-use inspection without repairing a malfunctioning part.
When not passing the in-use inspection due to more than one permanent DTC, permanent DTCs should be
erased, referring to this manual.
NOTE:
The important items in in-use inspection are that MIL is not ON, SRT test items are set, and permanent
DTCs are not included.
Permanent DTCs do not apply for regions that permanent DTCs are not regulated by law.
Revision: August 2014
EC-65
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
PERMANENT DTC SET TIMING
The setting timing of permanent DTC is stored in ECM with the lighting of MIL when a DTC is confirmed.
DIAGNOSIS DESCRIPTION : Malfunction Indicator Lamp (MIL)
INFOID:0000000011277883
When emission-related ECU detects a malfunction in the emission
control systems components and/or the powertrain control components (which affect vehicle emissions), it turns on/blinks MIL to
inform the driver that a malfunction has been detected.
1. The MIL illuminates when ignition switch is turned ON (engine is
not running).
NOTE:
Check the MIL circuit if MIL does not illuminate. Refer to EC479, "Diagnosis Procedure".
2. When the engine is started, the MIL should go off.
NOTE:
JSBIA1315ZZ
If MIL continues to illuminate/blink, perform self-diagnoses and
inspect/repair accordingly because an emission-related ECU has detected a malfunction in the emission
control systems components and/or the powertrain control components (which affect vehicle emissions).
On Board Diagnosis Function
INFOID:0000000011277884
ON BOARD DIAGNOSIS ITEM
The on board diagnostic system has the following functions.
Diagnostic test mode
Function
Bulb check
MIL can be checked.
SRT status
ECM can read if SRT codes are set.
Malfunction warning
If ECM detects a malfunction, it illuminates or blinks MIL to inform the driver that a malfunction has
been detected.
Self-diagnostic results
DTCs or 1st trip DTCs stored in ECM can be read.
Accelerator pedal released position learning
ECM can learn the accelerator pedal released position. Refer to EC-142, "Work Procedure".
Throttle valve closed position
learning
ECM can learn the throttle valve closed position. Refer to EC-143, "Work Procedure".
Idle air volume learning
ECM can learn the idle air volume. Refer to EC-144, "Work Procedure".
Mixture ratio self-learning value
clear
Mixture ratio self-learning value can be erased. Refer to EC-146, "Work Procedure".
BULB CHECK MODE
Description
This function allows damage inspection in the MIL bulb (blown, open circuit, etc.).
Operation Procedure
1.
2.
Turn ignition switch ON.
The MIL on the instrument panel should stay ON.
If it remains OFF, check MIL circuit. Refer to EC-479, "Diagnosis Procedure".
SRT STATUS MODE
Description
This function allows to read if ECM has completed the self-diagnoses of major emission control systems and
components. For SRT, refer to EC-64, "DIAGNOSIS DESCRIPTION : System Readiness Test (SRT) Code".
Operation Procedure
1.
2.
Turn ignition switch ON and wait 20 seconds.
SRT status is indicated as shown blow.
ECM continues to illuminate MIL if all SRT codes are set.
Revision: August 2014
EC-66
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
< SYSTEM DESCRIPTION >
ECM blinks MIL for about 10 seconds if all SRT codes are not set.
[QR25DE]
A
EC
JMBIA1515GB
MALFUNCTION WARNING MODE
Description
In this function ECM turns on or blinks MIL when it detects a malfunction in the emission control system components and/or the powertrain control components (which affect vehicle emissions) to inform the driver that a
malfunction has been detected.
Operation Procedure
1.
2.
3.
Turn ignition switch ON.
Check that MIL illuminates.
If it remains OFF, check MIL circuit. Refer to EC-479, "Diagnosis Procedure".
Start engine and let it idle.
For two trip detection logic diagnoses, ECM turns on MIL when it detects the same malfunction twice in
the two consecutive driving cycles.
For 1st trip detection logic diagnoses, ECM turns on MIL when it detects a malfunction in one driving
cycle.
ECM blinks MIL when it detects a malfunction that may damage the three way catalyst (misfire).
SELF-DIAGNOSTIC RESULTS MODE
Description
This function allows to indicate DTCs or 1st trip DTCs stored in ECM according to the number of times MIL is
blinking.
How to Set Self-diagnostic Results Mode
NOTE:
It is better to count the time accurately with a clock.
It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has a malfunction.
After ignition switch is turned off, ECM is always released from the self-diagnostic results mode.
1. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
2. Repeat the following procedure quickly five times within 5 seconds.
Fully depress the accelerator pedal.
Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it depressed for approx. 10 seconds until the
MIL starts blinking.
NOTE:
Do not release the accelerator pedal for 10 seconds if MIL starts blinking during this period. This blinking
is displaying SRT status and is continued for another 10 seconds.
4. Fully release the accelerator pedal.
ECM has entered to Self-diagnostic results mode.
Revision: August 2014
EC-67
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
NOTE:
Wait until the same DTC (or 1st trip DTC) appears to completely confirm all DTCs.
PBIB0092E
How to Read Self-diagnostic Results
The DTC and 1st trip DTC are indicated by the number of blinks of the MIL as shown below.
The DTC and 1st trip DTC are displayed at the same time. If the MIL does not illuminate in diagnostic test
mode I (Malfunction warning), all displayed items are 1st trip DTCs. If only one code is displayed when the MIL
illuminates in malfunction warning mode, it is a DTC; if two or more codes are displayed, they may be either
DTCs or 1st trip DTCs. DTC No. is same as that of 1st trip DTC. These unidentified codes can be identified by
using the CONSULT or GST. A DTC will be used as an example for how to read a code.
PBIB3005E
A particular trouble code can be identified by the number of four-digit numeral flashes per the following.
Number
Flashes
10
11
12
13
14
15
16
The length of time the 1,000th-digit numeral flashes on and off is 1.2 seconds consisting of an ON (0.6-seconds) - OFF (0.6-seconds) cycle.
The 100th-digit numeral and lower digit numerals consist of a 0.3-seconds ON and 0.3-seconds OFF cycle.
A change from one digit numeral to another occurs at an interval of 1.0-second OFF. In other words, the later
numeral appears on the display 1.3 seconds after the former numeral has disappeared.
A change from one trouble code to another occurs at an interval of 1.8-seconds OFF.
Revision: August 2014
EC-68
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
In this way, all the detected malfunctions are classified by their DTC numbers. The DTC 0000 refers to no malfunction. Refer to EC-96, "DTC Index".
How to Erase Self-diagnostic Results
By performing this procedure, ECM memory is erased and the following diagnostic information is erased as
EC
well.
Diagnostic trouble codes
1st trip diagnostic trouble codes
Freeze frame data
C
1st trip freeze frame data
System readiness test (SRT) codes
Test values
D
NOTE:
Also, if a battery terminal is disconnected, ECM memory is erased and the diagnostic information as listed
above is erased. (The amount of time required for erasing may vary from a few seconds to several hours.)
1. Turn ignition switch OFF and wait at least 10 seconds.
E
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
F
4. Turn ignition switch ON.
5. Set ECM in self-diagnostic results mode.
6. The diagnostic information has been erased from the backup memory in the ECM.
G
Fully depress the accelerator pedal and keep it depressed for more than 10 seconds.
7. Fully release the accelerator pedal, and confirm the DTC 0000 is displayed.
CONSULT Function
INFOID:0000000011277885
FUNCTION
I
Diagnostic test mode
Function
Self Diagnostic Result
Self-diagnostic results such as 1st trip DTC, DTC and 1st trip freeze frame data or freeze frame data
can be read and erased quickly.*
Data Monitor
Input/Output data in the ECM can be read.
Work support
This mode enables a technician to adjust some devices faster and more accurately by following the indications on the CONSULT screen.
Active Test
Diagnostic Test Mode in which CONSULT drives some actuators apart from the ECMs and also shifts
some parameters in a specified range.
ECU Identification
ECM part number can be read.
DTC Work Support
The status of system monitoring tests and the self-diagnosis status/results can be confirmed.
*: The following emission-related diagnostic information is cleared when the ECM memory is erased.
Diagnostic trouble codes
1st trip diagnostic trouble codes
Freeze frame data
1st trip freeze frame data
System readiness test (SRT) codes
Test values
SELF DIAGNOSTIC RESULT MODE
Self Diagnostic Item
Regarding items of DTC and 1st trip DTC, refer to EC-96, "DTC Index".)
How to Read DTC and 1st Trip DTC
DTCs and 1st trip DTCs related to the malfunction are displayed in self-diag results.
When ECM detects a 1st trip DTC, 1t is displayed for TIME.
When ECM has detected a current DTC, 0 is displayed for TIME.
If TIME is neither 0 nor 1t, the DTC occurred in the past and ECM shows the number of times the vehicle has been driven since the last detection of the DTC.
Revision: August 2014
EC-69
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
How to Erase DTC and 1st Trip DTC
NOTE:
If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10 seconds and then turn it ON (engine stopped) again.
Freeze Frame Data and 1st Trip Freeze Frame Data
Freeze frame data item*
Description
DIAG TROUBLE CODE
[PXXXX]
The engine control component part/control system has a trouble code that is displayed as PXXXX. (Refer to EC-96, "DTC Index".)
FUEL SYS-B1
CAL/LD VALUE [%]
The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP
[C] or [F]
The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%]
Long-term fuel trim at the moment a malfunction is detected is displayed.
The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule
than short-term fuel trim.
S-FUEL TRM-B1 [%]
Short-term fuel trim at the moment a malfunction is detected is displayed.
The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel
schedule.
ENGINE SPEED [rpm]
The engine speed at the moment a malfunction is detected is displayed.
VEHICL SPEED
[km/h] or [mph]
The vehicle speed at the moment a malfunction is detected is displayed.
ABSOL THP/S [%]
The throttle valve opening angle at the moment a malfunction is detected is displayed.
B/FUEL SCHDL [msec]
The base fuel schedule at the moment a malfunction is detected is displayed.
INT/A TEMP SE
[C] or [F]
The intake air temperature at the moment a malfunction is detected is displayed.
Fuel injection system status at the moment a malfunction is detected is displayed.
One of the following mode is displayed.
Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop
FUEL SYS-B2
L-FUEL TRM-B2 [%]
S-FUEL TRM-B2 [%]
There items are displayed but are not applicable to this model.
INT MANI PRES [kPa]
COMBUST CONDITION
*: The items are the same as those of 1st trip freeze frame data.
DATA MONITOR MODE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitored Item
Revision: August 2014
EC-70
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
Monitored item
Unit
ENG SPEED
rpm
B/FUEL SCHDL
msec
A/F ALPHA-B1
COOLAN TEMP/S
C or F
HO2S2 (B1)
VHCL SPEED SE
MAIN
SIGNAL
S
Description
Remarks
Indicates the engine speed computed
from the signal of the crankshaft position
sensor (POS) and camshaft position sensor (PHASE).
Accuracy becomes poor if engine speed drops below the
idle rpm.
If the signal is interrupted while
the engine is running, an abnormal value may be indicated.
Base fuel schedule indicates the fuel injection pulse width programmed into
ECM, prior to any learned on board correction.
When engine is running, specification range is indicated in
SPEC.
The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.
When the engine is stopped, a
certain value is indicated.
When engine is running, specification range is indicated in
SPEC.
This data also includes the
data for the air-fuel ratio learning control.
A/F SEN1 (B1)
HO2S2 MNTR(B1)
ECU
INPUT
SIGNALS
RICH/LEAN
km/h or mph
BATTERY VOLT
The engine coolant temperature (determined by the signal voltage of the engine
coolant temperature sensor) is displayed.
The A/F signal computed from the input
signal of the air fuel ratio (A/F) sensor 1
is displayed.
The signal voltage of the heated oxygen
sensor 2 is displayed.
Display of heated oxygen sensor 2 signal.
- RICH: means the amount of oxygen after
three way catalyst is relatively small.
- LEAN: means the amount of oxygen after
three way catalyst is relatively large.
TP SEN 1-B1
V
TP SEN 2-B1
FUEL T/TMP SE
C or F
Revision: August 2014
When the engine is stopped, a
certain value is indicated.
The accelerator pedal position sensor
signal voltage is displayed.
The throttle position sensor signal voltage is displayed.
TP SEN 2-B1 signal is converted by ECM internally. Thus, it
differs from ECM terminal voltage signal.
The fuel temperature (determined by the
signal voltage of the fuel tank temperature sensor) is displayed.
EC-71
ACCEL SEN 2 signal is converted by ECM internally.
Thus, it differs from ECM terminal voltage signal.
The vehicle speed computed from the
vehicle speed signal sent from combination meter is displayed.
ACCEL SEN 1
The power supply voltage of ECM is displayed.
ACCEL SEN 2
When the engine coolant temperature sensor is open or
short-circuited, ECM enters
fail-safe mode. The engine
coolant temperature determined by the ECM is displayed.
EC
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
Monitored item
Unit
EVAP SYS PRES
FUEL LEVEL SE
ECU
INPUT
SIGNALS
MAIN
SIGNAL
S
Description
Remarks
The signal voltage of EVAP control system pressure sensor is displayed.
The signal voltage of the fuel level sensor
is displayed.
Indicates start signal status [ON/OFF]
computed by the ECM according to the
signals of engine speed and battery voltage.
START SIGNAL
On/Off
CLSD THL POS
On/Off
Indicates idle position [ON/OFF] computed by ECM according to the accelerator
pedal position sensor signal.
AIR COND SIG
On/Off
Indicates [ON/OFF] condition of the air
conditioner switch as determined by the
air conditioner signal.
PW/ST SIGNAL
On/Off
[ON/OFF] condition of the power steering
system (determined by the signal sent
from EPS control unit) is indicated.
After starting the engine, [OFF]
is displayed regardless of the
starter signal.
LOAD SIGNAL
On/Off
Indicates [ON/OFF] condition from the
electrical load signal.
- On: Rear window defogger switch is ON
and/or lighting switch is in 2nd position.
- Off: Both rear window defogger switch
and lighting switch are OFF.
IGNITION SW
On/Off
Indicates [ON/OFF] condition from ignition switch signal.
HEATER FAN SW
On/Off
BRAKE SW
On/Off
Indicates [ON/OFF] condition from the
stop lamp switch signal.
INJ PULSE-B1
msec
Indicates the actual fuel injection pulse
width compensated by ECM according to
the input signals.
When the engine is stopped, a
certain computed value is indicated.
IGN TIMING
BTDC
Indicates the ignition timing computed by
ECM according to the input signals.
When the engine is stopped, a
certain value is indicated.
Indicates [ON/OFF] condition from the
heater fan switch signal.
CAL/LD VALUE
Calculated load value indicates the value of the current air flow divided by peak
air flow.
MASS AIRFLOW
g/s
Indicates the mass air flow computed by
ECM according to the signal voltage of
the mass air flow sensor.
Indicates the EVAP canister purge volume control solenoid valve control value
computed by the ECM according to the
input signals.
The opening becomes larger as the value increases.
PURG VOL C/V
INT/V TIM(B1)
CA
Indicates [CA] of intake camshaft advance angle.
EXH/V TIM B1
CA
Indicates [CA] of exhaust camshaft advance angle.
Revision: August 2014
EC-72
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
Monitored item
Unit
INT/V SOL(B1)
ECU
INPUT
SIGNALS
MAIN
SIGNAL
S
A
Description
Remarks
EC
The control value of the intake valve timing control solenoid valve (determined by
ECM according to the input signals) is indicated.
The advance angle becomes larger as
the value increases.
On/Off
The control condition of the intake manifold runner control valve (determined by
ECM according to the input signals) is indicated.
- On: Closed
- Off: Open
On/Off
The air conditioner relay control condition (determined by ECM according to
the input signals) is indicated.
On/Off
Indicates the fuel pump relay control condition determined by ECM according to
the input signals.
VENT CONT/V
On/Off
The control condition of the EVAP canister vent control valve (determined by
ECM according to the input signals) is indicated.
- On: Closed
- Off: Open
THRTL RELAY
On/Off
Indicates the throttle control motor relay
control condition determined by the ECM
according to the input signals.
Indicates a command value for cooling
fan. The value is calculated by ECM
based on input signals.
On/Off
Indicates [ON/OFF] condition of heated
oxygen sensor 2 heater determined by
ECM according to the input signals.
SWRL CONT S/V
AIR COND RLY
FUEL PUMP RLY
FAN DUTY
HO2S2 HTR (B1)
rpm
Indicates the engine speed computed
from the input speed sensor signal.
km/h or mph
The vehicle speed computed from the
vehicle speed signal sent from TCM is
displayed.
YET/CMPLT
Displays the condition of Idle Air Volume
Learning
- YET: Idle air volume learning has not
been performed yet.
- CMPLT: Idle air volume learning has already been performed successfully.
km or mile
Distance traveled while MIL is activated.
C or F
The engine oil temperature (determined
by the signal voltage of the engine oil
temperature sensor) is displayed.
I/P PULLY SPD
VEHICLE SPEED
IDL A/V LEARN
TRVL AFTER MIL
ENG OIL TEMP
Revision: August 2014
EC-73
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
Monitored item
Unit
ECU
INPUT
SIGNALS
MAIN
SIGNAL
S
Description
Air fuel ratio (A/F) sensor 1 heater control
value computed by ECM according to the
input signals.
The current flow to the heater becomes
larger as the value increases.
VHCL SPEED SE
km/h or mph
The vehicle speed computed from the
vehicle speed signal sent from combination meter is displayed.
SET VHCL SPD
km/h or mph
The preset vehicle speed is displayed.
A/F S1 HTR(B1)
MAIN SW
On/Off
Indicates [ON/OFF] condition from MAIN
switch signal.
CANCEL SW
On/Off
Indicates [ON/OFF] condition from CANCEL switch signal.
RESUME/ACC SW
On/Off
Indicates [ON/OFF] condition from RESUME/ACCELERATE switch signal.
SET SW
On/Off
Indicates [ON/OFF] condition from SET/
COAST switch signal.
BRAKE SW1
On/Off
Indicates [ON/OFF] condition from brake
pedal position switch signal.
BRAKE SW2
On/Off
Indicates [ON/OFF] condition of stop
lamp switch signal.
Non/Cut
Indicates the vehicle cruise condition.
- Non: Vehicle speed is maintained at the
ASCD set speed.
- Cut: Vehicle speed decreased to excessively low compared with the ASCD set
speed, and ASCD operation is cut off.
Non/Cut
Indicates the vehicle cruise condition.
- Non: Vehicle speed is maintained at the
ASCD set speed.
- Cut: Vehicle speed decreased to excessively low, and ASCD operation is cut off.
AT OD MONITOR
On/Off
Indicates [ON/OFF] condition of CVT O/
D according to the input signal from the
TCM.
AT OD CANCEL
On/Off
Indicates [ON/OFF] condition of CVT O/
D cancel request signal.
CRUISE LAMP
On/Off
Indicates [ON/OFF] condition of CRUISE
lamp determined by the ECM according
to the input signals.
SET LAMP
On/Off
Indicates [ON/OFF] condition of SET
lamp determined by the ECM according
to the input signals.
A/F ADJ-B1
Indicates the correction of factor stored in
ECM. The factor is calculated from the
difference between the target air-fuel ratio stored in ECM and the air-fuel ratio
calculated from A/F sensor 1 signal.
TUMBLE POS SEN
The intake manifold runner control valve
position sensor signal voltage is displayed.
VHCL SPD CUT
LO SPEED CUT
Revision: August 2014
EC-74
Remarks
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
ECU
INPUT
SIGNALS
MAIN
SIGNAL
S
On/Off
Indicates [ON/OFF] condition from the
park/neutral position (PNP) signal.
INT/A TEMP SE
C or F
The intake air temperature (determined
by the signal voltage of the intake air temperature sensor) is indicated.
AC PRESS SEN
The signal voltage from the refrigerant
pressure sensor is displayed.
The control value of the exhaust valve
timing control solenoid valve (determined
by ECM according to the input signals) is
indicated.
The advance angle becomes larger as
the value increases.
Monitored item
P/N POSI SW
Unit
VTC DTY EX B1
EVAP DIAG
READY
The signal voltage of engine oil pressure
sensor is displayed.
YET/CMPLT
Indicates the condition of EVAP leak diagnosis.
YET: EVAP leak diagnosis has not been
performed yet.
CMPLT: EVAP leak diagnosis has been
performed successfully.
ON/OFF
Indicates the ready condition of EVAP
leak diagnosis.
ON: Diagnosis has been ready condition.
OFF: Diagnosis has not been ready condition.
THRTL STK CNT
B1*
A/F SEN1
DIAG1(B1)
INCMP/CMPLT
A/F SEN1
DIAG2(B1)
INCMP/CMPLT
Indicates DTC P014C or P014D self-diagnosis condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
ABSNT/
PRSNT
Indicates DTC P014C, P014D, P015A or
P015B self-diagnosis condition.
- ABSNT: The vehicle condition is not within the diagnosis range.
- PRSNT: The vehicle condition is within
the diagnosis range.
HO2 S2 DIAG1
(B1)
INCMP/CMPLT
Indicates DTC P0139 self-diagnosis (delayed response) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
HO2 S2 DIAG2
(B1)
INCMP/CMPLT
Indicates DTC P0139 self-diagnosis
(slow response) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
Revision: August 2014
Indicates DTC P015A or P015B self-diagnosis condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
A/F SEN1
DIAG3(B1)
Remarks
EC
mV
EOP SENSOR
EVAP LEAK DIAG
Description
EC-75
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
Monitor Item
Selection
Monitored item
Unit
ECU
INPUT
SIGNALS
MAIN
SIGNAL
S
Description
SYSTEM 1 DIAGNOSIS A B1
INCMP/CMPLT
Indicates DTC P117A self-diagnosis condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAGNOSIS B B1
ABSNT/
PRSNT
Indicates DTC P117A self-diagnosis condition.
- ABSNT: Self-diagnosis standby
- PRSNT: Under self-diagnosis
MASS AIR FLOW
SENSOR (Hz)
The signal frequency of the mass air flow
sensor is displayed.
Hz
Remarks
When the engine is stopped, a
certain value is indicated.
When engine is running, specification range is indicated in
SPEC.
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
WORK SUPPORT MODE
Work Item
Work item
Condition
Usage
IDLE AIR VOL LEARN
The idle air volume that keeps the engine within the specified range is memorized in ECM.
When learning the idle air volume
EVAP SYSTEM CLOSE
Close the EVAP canister vent control valve in order to make
EVAP system close under the following conditions.
Ignition switch ON
Engine not running
Ambient temperature is above 0C (32F).
No vacuum and no high pressure in EVAP system
Fuel tank temp is more than 0C (32F).
Within 10 minutes after starting EVAP SYSTEM CLOSE
When trying to execute EVAP SYSTEM CLOSE under
the condition except above, CONSULT will discontinue it
and display appropriate instruction.
NOTE:
When starting engine, CONSULT may display BATTERY VOLTAGE IS LOW. CHARGE BATTERY, even in
when using a charged battery.
When detecting EVAP vapor leak
in the EVAP system
FUEL PRESSURE RELEASE
Fuel pump will stop by touching START during idling.
Crank a few times after engine stalls.
When releasing fuel pressure from
fuel line
TARGET IGN TIM ADJ*
Idle condition
When adjusting target ignition timing
TARGET IDLE RPM ADJ*
Idle condition
When setting target idle speed
VIN REGISTRATION
In this mode, VIN is registered in ECM.
When registering VIN in ECM
SELF-LEARNING CONT
The coefficient of self-learning control mixture ratio returns
to the original coefficient.
When clearing mixture ratio selflearning value
CLSD THL POS LEARN
Ignition on and engine stopped.
When learning the throttle valve
closed position
SAVING DATA FOR REPLC CPU
In this mode, save data that is in ECM.
SAVING DATA FOR REPLC CPU
WRITING DATA FOR REPLC CPU
In this mode, write data stored by SAVE DATA FOR CPU
REPLC in work support mode to ECM.
WRITING DATA FOR REPLC
CPU
Revision: August 2014
EC-76
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
*: This function is not necessary in the usual service procedure.
ACTIVE TEST MODE
Test Item
Test item
Condition
Judgment
Check item (Remedy)
FUEL INJECTION
Engine: Return to the original
trouble condition
Change the amount of fuel injection using CONSULT.
If trouble symptom disappears, see
CHECK ITEM.
Harness and connectors
Fuel injector
Air fuel ratio (A/F) sensor 1
ENG COOLANT
TEMP
Engine: Return to the original
trouble condition
Change the engine coolant temperature using CONSULT.
If trouble symptom disappears, see
CHECK ITEM.
Harness and connectors
Engine coolant temperature
sensor
Fuel injector
PURG VOL CONT/V
Engine: After warming up, run engine at 1,500 rpm.
Change the EVAP canister purge
volume control solenoid valve
opening percent using CONSULT.
EC
E
Engine speed changes according
to the opening percent.
Harness and connectors
Solenoid valve
FUEL/T TEMP SEN
Change the fuel tank temperature using CONSULT.
FAN DUTY CONTROL*
Ignition switch: ON
Change duty ratio using CONSULT.
Cooling fan speed changes.
FUEL PUMP RELAY
Ignition switch: ON (Engine
stopped)
Turn the fuel pump relay ON
and OFF using CONSULT and
listen to operating sound.
Fuel pump relay makes the operating sound.
Harness and connectors
Fuel pump relay
TUMBLE CONTROL
VALVE
Ignition switch: ON
Turn intake manifold runner control valve ON and OFF using
CONSULT and listen to operating
sound.
Intake Manifold Runner control
valve motor makes an operating
sound.
Harness and connectors
Intake Manifold Runner control
valve motor
IGNITION TIMING
Engine: Return to the original
trouble condition
Timing light: Set
Retard the ignition timing using
CONSULT.
If trouble symptom disappears, see
CHECK ITEM.
Perform Idle Air Volume Learning.
POWER BALANCE
Engine: After warming up, idle the
engine.
A/C switch OFF
Selector lever: P or N
Cut off each fuel injector signal
one at a time using CONSULT.
Engine runs rough or stops.
VENT CONTROL/V
Ignition switch: ON (Engine
stopped)
Turn solenoid valve ON and
OFF using CONSULT and listen
to operating sound.
INT V/T ASSIGN ANGLE
EXH V/T ASSIGN
ANGLE
Harness and connectors
Cooling fan motor
Cooling fan relay
Cooling fan control module
IPDM E/R
Harness and connectors
Compression
Fuel injector
Power transistor
Spark plug
Ignition coil
Solenoid valve makes an operating
sound.
Harness and connectors
Solenoid valve
Engine: Return to the original
trouble condition
Change intake valve timing using
CONSULT.
If trouble symptom disappears, see
CHECK ITEM.
Harness and connectors
Intake valve timing control solenoid valve
Engine: Return to the original
trouble condition
Change exhaust valve timing using CONSULT.
If trouble symptom disappears, see
CHECK ITEM.
Harness and connectors
Exhaust valve timing control solenoid valve
Revision: August 2014
EC-77
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
DTC WORK SUPPORT MODE
Test Item
Test mode
Test item
A/F SEN1(B1) P1276
A/F SEN1
EVAPORATIVE SYSTEM
HO2S2
Corresponding DTC No.
Reference page
P0130
EC-229
A/F SENSOR1(B1) P014C/P014D
P014C, P014D
EC-258
A/F SENSOR1(B1) P015A/P015B
P015A, P015B
EC-258
PURG FLOW P0441
P0441
EC-309
PURG VOL CN/V P1444
P0443
EC-314
HO2S2(B1) P1146
P0138
EC-245
HO2S2(B1) P1147
P0137
EC-239
HO2S2(B1) P0139
P0139
EC-252
SRT & P-DTC MODE
SRT STATUS Mode
For items whose SRT codes are set, CMPLT is displayed on the CONSULT screen; for items whose SRT
codes are not set, INCMP is displayed.
SRT STATUS provides the presence or absence of permanent DTCs stored in ECM memory.
PERMANENT DTC STATUS Mode
How to display permanent DTC status
1.
2.
3.
4.
5.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS in DTC & SRT CONFIRMATION mode with CONSULT.
NOTE:
Permanent DTCs stored in ECM memory are displayed on the CONSULT screen to show if a driving pattern required for erasing permanent DTCs is complete (CMPLT) or incomplete (INCMP).
CAUTION:
Since the PERMANENT DTC STATUS screen displays the previous trip information, repeat the
following twice to update the information: Ignition switch OFF, Wait for more than 10 seconds
and Ignition switch ON.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
JSBIA0062GB
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
Revision: August 2014
EC-78
2015 Rogue NAM
DIAGNOSIS SYSTEM (ECM)
[QR25DE]
< SYSTEM DESCRIPTION >
PERMANENT DTC WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to complete the driving pattern that is required for erasing
permanent DTC.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
EC
Revision: August 2014
EC-79
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION
ECM
Reference Value
INFOID:0000000011277886
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
zNumerical values in the following table are reference values.
zThese values are input/output values that ECM receives/transmits and may differ from actual operations.
Example:
The ignition timing shown by the timing light may differ from the ignition timing displayed on the data monitor.
This occurs because the timing light shows a value calculated by ECM according to signals received from the
cam shaft position sensor and other sensors related to ignition timing.
Monitor Item
Condition
ENG SPEED
Run engine and compare CONSULT value with the tachometer indication.
B/FUEL SCHDL
See EC-161, "Diagnosis Procedure".
A/F ALPHA-B1
See EC-161, "Diagnosis Procedure".
Values/Status
Almost the same speed as
the tachometer indication.
COOLAN TEMP/S
Engine: After warming up
A/F SEN1 (B1)
Engine: After warming up
More than 70C (158F)
HO2S2 (B1)
Revving engine from idle up to 3,000 rpm quickly after the following conditions
are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
0 - 0.3 V Approx. 0.6 1.0 V
HO2S2 MNTR(B1)
Revving engine from idle up to 3,000 rpm quickly after the following conditions
are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
LEAN RICH
VHCL SPEED SE
Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as
speedometer indication
BATTERY VOLT
Ignition switch: ON (Engine stopped)
Maintaining engine speed at 2,000 rpm
Fluctuates around 2.2 V
11 - 14 V
ACCEL SEN 1
Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
Accelerator pedal: Fully depressed
4.2 - 4.8 V
ACCEL SEN 2*
Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
0.5 - 1.0 V
Accelerator pedal: Fully depressed
4.2 - 4.8 V
Ignition switch: ON
(Engine stopped)
Selector lever: D
Accelerator pedal: Fully released
More than 0.36 V
TP SEN 1-B1
Accelerator pedal: Fully depressed
Less than 4.75 V
Ignition switch: ON
(Engine stopped)
Selector lever: D
Accelerator pedal: Fully released
Less than 4.75 V
TP SEN 2-B1*
Accelerator pedal: Fully depressed
More than 0.36 V
FUEL T/TMP SE
Ignition switch: ON
EVAP SYS PRES
Ignition switch: ON
Approx. 1.8 - 4.8 V
FUEL LEVEL SE
Ignition switch: ON
Depending on fuel level of
fuel tank
START SIGNAL
Ignition switch: ON START ON
Revision: August 2014
0.5 - 1.0 V
Indicates fuel tank temperature
EC-80
Off On Off
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Monitor Item
Condition
CLSD THL POS
Ignition switch: ON
(Engine stopped)
AIR COND SIG
Engine: After warming up, idle the
engine
PW/ST SIGNAL
Engine: After warming up, idle the
engine
LOAD SIGNAL
Ignition switch: ON
IGNITION SW
Ignition switch: ON OFF ON
HEATER FAN SW
Engine: After warming up, idle the
engine
Values/Status
Accelerator pedal: Fully released
On
Accelerator pedal: Slightly depressed
Off
Air conditioner switch: OFF
Off
Air conditioner switch: ON
(Compressor operates.)
On
Steering wheel: Not being turned
Off
Steering wheel: Being turned
On
Rear window defogger switch: ON
and/or Lighting switch: 2nd position
On
Rear window defogger switch and lighting
switch: OFF
Off
On Off On
Heater fan switch: ON
On
Heater fan switch: OFF
Off
Brake pedal: Fully released
Off
Brake pedal: Slightly depressed
On
BRAKE SW
Ignition switch: ON
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
2.0 - 3.0 msec
INJ PULSE-B1
2,000 rpm
1.9 - 2.9 msec
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
5 - 15 BTDC
IGN TIMING
2,000 rpm
25 - 45 BTDC
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
10% - 35%
CAL/LD VALUE
2,500 rpm
10% - 35%
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
1.0 - 4.0 g/s
MASS AIRFLOW
2,500 rpm
4.0 - 10.0 g/s
PURG VOL C/V
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.)
2,000 rpm
20% - 90%
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
5 - 5CA
INT/V TIM(B1)
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
EXH/V TIM B1
Engine: Idle speed
Selector lever: P or N
Air conditioner switch: OFF
No load
After warming up
INT/V SOL (B1)
SWRL CONT S/V
Ignition switch: ON
Engine coolant temperature: Between -7C (19F) and 60C
(140F)
Revision: August 2014
4,000 rpm
2,000 rpm
Cold condition [Engine coolant temperature below 60C (140F)]
0%
EC
Approx. 0 - 30CA
5 - 5CA
Approx. 0 - 40CA
0%
Approx. 50% - 100%
Accelerator pedal: Fully released
On
Accelerator pedal: Fully depressed
Off
EC-81
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Monitor Item
AIR COND RLY
FUEL PUMP RLY
VENT CONT/V
Condition
Engine: After warming up, idle the
engine
Air conditioner switch: OFF
Off
Air conditioner switch: ON
(Compressor operates)
On
For 1 second after turning ignition switch: ON
Engine running or cranking
On
Except above
Off
Ignition switch: ON
Off
THRTL RELAY
Ignition switch: ON
FAN DUTY
Engine: Running
HO2S2 HTR (B1)
Values/Status
On
0 - 100%
Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
On
Engine speed: Above 3,600 rpm
Off
I/P PULLY SPD
Vehicle speed: More than 20 km/h (12 MPH)
Almost the same speed as
the tachometer indication
VEHICLE SPEED
Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as
the speedometer indication
IDL A/V LEARN
Engine: running
Idle air volume learning has not been performed yet.
YET
Idle air volume learning has already been
performed successfully.
CMPLT
Vehicle has traveled after MIL has turned
ON.
0 - 65,535 km
(0 - 40,723 miles)
TRVL AFTER MIL
Ignition switch: ON
ENG OIL TEMP
Engine: After warming up
A/F S1 HTR(B1)
Engine: After warming up, idle the engine
(More than 140 seconds after starting engine.)
VHCL SPEED SE
Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as
the speedometer indication
SET VHCL SPD
Engine: Running
The preset vehicle speed is
displayed
MAIN SW
Ignition switch: ON
CANCEL SW
RESUME/ACC SW
Ignition switch: ON
Ignition switch: ON
More than 70C (158F)
ASCD: Operating
MAIN switch: Pressed
4 - 100%
On
MAIN switch: Released
Off
CANCEL switch: Pressed
On
CANCEL switch: Released
Off
RESUME/ACCELERATE switch:
Pressed
On
RESUME/ACCELERATE switch: Released
Off
SET/COAST switch: Pressed
On
SET/COAST switch: Released
Off
Brake pedal: Fully released
On
Brake pedal: Slightly depressed
Off
Brake pedal: Fully released
Off
Brake pedal: Slightly depressed
On
SET SW
Ignition switch: ON
BRAKE SW1
(Brake pedal position switch)
Ignition switch: ON
BRAKE SW2
(Stop lamp switch)
Ignition switch: ON
VHCL SPD CUT
Ignition switch: ON
Non
LO SPEED CUT
Ignition switch: ON
Non
AT OD MONITOR
Ignition switch: ON
Off
AT OD CANCEL
Ignition switch: ON
Off
Revision: August 2014
EC-82
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Monitor Item
Condition
MAIN switch: Pressed at the 1st time
at the 2nd time
Values/Status
Ignition switch: ON
SET LAMP
MAIN switch: ON
When vehicle speed: Between 40
km/h (25 MPH) and 144 km/h (89
MPH)
A/F ADJ-B1
Engine: running
TUMBLE POS SEN
Ignition switch: ON
Engine coolant temperature: Between -7C (19F) and 60C
(140F)
P/N POSI SW
Ignition switch: ON
INT/A TEMP SE
Ignition switch: ON
AC PRESS SEN
Engine speed: Idle
Both A/C switch and blower fan switch: ON (Compressor operates)
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
VTC DTY EX B1
Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load
Idle
1,000 - 2,000 mV
EOP SENSOR
2,000 rpm
1,500 - 3,500 mV
EVAP LEAK DIAG
Ignition switch: ON
Indicates the condition of
EVAP leak diagnosis.
EVAP DIAG READY
Ignition switch: ON
Indicates the ready condition
of EVAP leak diagnosis.
THRTL STK CNT B1
NOTE:
The item is indicated, but not used.
ASCD: Operating
On
ASCD: Not operating
Off
0.330 - 0.330
Accelerator pedal: Fully released
Less than 1.4 V
Accelerator pedal: Fully depressed
More than 2.8 V
Selector lever: P or N
On
Selector lever: Except above
Off
2,000 rpm
1.0 - 4.0 V
Approx. 0- 90%
DTC P015A and P015B self-diagnosis is complete.
CMPLT
A/F SEN1 DIAG2
(B1)
DTC P014C and P014D self-diagnosis is incomplete.
INCMP
DTC P014C and P014D self-diagnosis is complete.
CMPLT
The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
ABSNT
The vehicle condition is within the diagnosis range of DTC P014C, P014D,
P015A or P015B.
PRSNT
DTC P0139 self-diagnosis (delayed response) is incomplete.
INCMP
DTC P0139 self-diagnosis (delayed response) is complete.
CMPLT
DTC P0139 self-diagnosis (slow response) is incomplete.
INCMP
DTC P0139 self-diagnosis (slow response) is complete.
CMPLT
SYSTEM 1 DIAGNOSIS A B1
INCMP
DTC P117A self-diagnosis is complete.
CMPLT
SYSTEM 1 DIAGNOSIS B B1
DTC P117A self-diagnosis is on standby.
ABSENT
DTC P117A self-diagnosis is under diagnosis.
PRSENT
See EC-161, "Diagnosis Procedure".
*: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ from
ECM terminals voltage signal.
Revision: August 2014
EC-83
DTC P117A self-diagnosis is incomplete.
MASS AIR FLOW
SENSOR (Hz)
INCMP
HO2 S2 DIAG2 (B1)
0 - 2%
DTC P015A and P015B self-diagnosis is incomplete.
HO2 S2 DIAG1 (B1)
EC
Indicates intake air temperature
A/F SEN1 DIAG1
(B1)
A/F SEN1 DIAG3
(B1)
On Off
CRUISE LAMP
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
TERMINAL LAYOUT
JSBIA0505ZZ
PHYSICAL VALUES
NOTE:
ECM is located in the engine room left side near battery.
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT.
Terminal No.
(Wire color)
+
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
1.8 V
1
(G)
128
(BR)
Throttle control motor
(Close)
Output
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully released
JMBIA0326GB
2
(GR)
128
(BR)
Throttle control motor
power supply
Input
[Ignition switch: ON]
Battery voltage
(11 - 14 V)
3.2 V
3
(L)
128
(BR)
Throttle control motor
(Open)
Output
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully depressed
JMBIA0324GB
4
(W)
8
()
8
()
Knock sensor
Sensor ground
(Knock sensor shield circuit)
Revision: August 2014
Input
[Engine is running]
Idle speed
EC-84
2.5 V
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
Battery voltage
9
(Y)
10
(P)
13
(L)
14
(G)
[Engine is running]
Warm-up condition
Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
128
(BR)
Fuel injector No. 4
Fuel injector No. 3
Fuel injector No. 1
Fuel injector No. 2
(11 - 14 V)
D
JMBIA0089GB
Output
Battery voltage
(11 - 14 V)
[Engine is running]
Warm-up condition
Engine speed: 2,000 rpm
ECM ground
JMBIA0090GB
16
(BR)
EC
Battery voltage
(11 - 14 V)
[Engine is running]
Idle speed
Accelerator pedal: Not depressed
even slightly, after engine starting
17
(BG)
128
(BR)
EVAP canister purge volume control solenoid
valve
J
JMBIA0087GB
Output
Battery voltage
(11 - 14 V)
[Engine is running]
Engine speed: About 2,000 rpm
(More than 100 seconds after starting engine.)
M
JMBIA0088GB
18
(P)
21
(V)
128
(BR)
128
(BR)
Fuel pump relay
Throttle control motor relay
Revision: August 2014
Output
Output
[Ignition switch: ON]
For 1 second after turning ignition
switch ON
[Engine is running]
0 - 1.0 V
[Ignition switch: ON]
More than 1 second after turning ignition switch ON
Battery voltage
(11 - 14 V)
[Ignition switch: OFF]
Battery voltage
(11 - 14 V)
[Ignition switch: ON]
0 - 1.0 V
EC-85
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
Description
Signal name
Input/
Output
Condition
Value
(Approx.)
0 - 1.0 V
22
(Y)
23
(B)
Heated oxygen sensor 2
Input
[Engine is running]
Revving engine from idle to 3,000
rpm quickly after the following conditions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load
23
(B)
Sensor ground
(Heated oxygen sensor 2)
25
(P)
26
(BR)
Engine oil temperature
sensor
Input
26
(BR)
Sensor ground
(Engine oil temperature
sensor)
27
(L)
Sensor ground
(Engine coolant temperature sensor)
28
(G)
27
(L)
Engine coolant temperature sensor
Input
30
(R)
Sensor ground
[Camshaft position sensor (PHASE)]
[Engine is running]
[Engine is running]
0 - 4.8 V
Output voltage varies with engine
oil temperature.
0 - 4.8 V
Output voltage varies with engine
coolant temperature.
1.0 - 2.0
[Engine is running]
Warm-up condition
Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
31
(W)
30
(R)
Camshaft position sensor
(PHASE)
JPBIA4726ZZ
Input
1.0 - 2.0
[Engine is running]
Engine speed is 2,000 rpm
JPBIA4727ZZ
32
(B)
33
(V)
34
(GR)
34
(GR)
Sensor power supply
[Camshaft position sensor (PHASE)]
Intake air temperature
sensor
Sensor ground
(Mass air flow sensor, intake air temperature sensor)
Revision: August 2014
Input
[Ignition switch: ON]
[Engine is running]
EC-86
5.0 V
0 - 4.8 V
Output voltage varies with intake
air temperature.
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
35
(BR)
Description
34
(GR)
Signal name
Mass air flow sensor
Condition
Input/
Output
Input
Value
(Approx.)
EC
[Ignition switch: ON]
Engine stopped
1.3 V
[Engine is running]
Warm-up condition
Idle speed
1.3 - 1.6 V
1.3 - 1.6 to 2.5 V (Check for linear
voltage rise in response to engine being increased to about
4,000 rpm.)
[Engine is running]
Warm-up condition
Engine is revving from idle to about
4,000 rpm
Sensor power supply
(Mass air flow sensor, intake air temperature sensor)
[Ignition switch: ON]
37
()
Shield
38
(SB)
Sensor ground
(Engine oil pressure sensor)
36
(L)
5.0 V
1.3 V
H
[Engine is running]
Warm-up condition
Idle speed
39
(P)
38
(SB)
Engine oil pressure sensor
I
JPBIA3359ZZ
Input
2.7 V
[Engine is running]
Warm-up condition
Engine speed is 2,000 rpm
JPBIA3360ZZ
40
(W)
38
(SB)
Sensor power supply
(Engine oil pressure sensor)
41
(Y)
128
(BR)
A/F sensor 1
42
(B)
Sensor ground
[Exhaust valve timing
control position sensor]
[Ignition switch: ON]
5.0 V
Input
[Ignition switch: ON]
2.2 V
Output voltage varies with air fuel
ratio.
Revision: August 2014
EC-87
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
1.0 - 2.0
[Engine is running]
Warm-up condition
Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
43
(LG)
42
(B)
Exhaust valve timing control position sensor
JPBIA4730ZZ
Input
1.0 - 2.0
[Engine is running]
Engine speed is 2,000 rpm
JPBIA4731ZZ
Sensor power supply
[Exhaust valve timing
control position sensor]
44
(Y)
45
(G)
128
(BR)
A/F sensor 1
49
(G)
128
(BR)
Intake manifold runner
control valve motor
(Close)
50
(V)
128
(BR)
Intake manifold runner
control valve motor power
supply
51
(Y)
128
(BR)
Intake manifold runner
control valve motor
(Open)
52
(B)
ECM ground
Input
Output
Input
[Ignition switch: ON]
[Engine is running]
Engine speed is 2,000 rpm
[Ignition switch ON]
Engine coolant temperature: Between -7C (19F) and 60C (140F)
Accelerator pedal: Depressed fully released
[Ignition switch: ON]
5V
1.8 V
Battery voltage appears for about
1 second.
Battery voltage
(11 - 14 V)
Output
[Ignition switch ON]
Engine coolant temperature: Between -7C (19F) and 60C (140F)
Accelerator pedal: Fully released
depressed
Battery voltage appears for about
1 second.
2.9 - 8.8 V
53
(P)
128
(BR)
A/F sensor 1 heater
Input
[Engine is running]
Warm-up condition
Idle speed
(More than 140 seconds after starting engine)
JPBIA4732ZZ
Revision: August 2014
EC-88
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
54
(V)
Description
128
(BR)
Signal name
Heated oxygen sensor 2
heater
Condition
Input/
Output
Output
[Engine is running]
Engine speed: Below 3,600 rpm after the following conditions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load
[Ignition switch: ON]
Engine stopped
[Engine is running]
Engine speed: Above 3,600 rpm
56
(GR)
70
(BR)
128
(BR)
Output
Sensor ground
[Crankshaft position sensor (POS)]
EC
10 V
JMBIA0325GB
0V
[Engine is running]
Cold condition [Engine coolant temperature: below 60C (140F)]
Idle speed
Battery voltage
(11 - 14 V)
4.0 V
[Engine is running]
Warm-up condition
Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
71
(GR)
70
(BR)
Crankshaft position sensor (POS)
Battery voltage
(11 - 14 V)
[Engine is running]
Warm-up condition
Idle speed
Intake valve timing intermediate lock control solenoid valve
Value
(Approx.)
JPBIA4728ZZ
Input
4.0 V
[Engine is running]
Engine speed: 2,000 rpm
M
JPBIA4729ZZ
72
(L)
Sensor power supply
[Crankshaft position sensor (POS)]
[Ignition switch: ON]
73
()
Shield
77
(W)
78
(B)
78
(B)
Throttle position sensor 2
Sensor ground
(Throttle position sensor
1, 2)
Revision: August 2014
Input
5.0 V
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully released
Less than 4.75 V
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully depressed
More than 0.36 V
EC-89
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
79
(G)
78
(B)
80
(R)
81
(R)
128
(BR)
83
(L)
Description
92
(LG)
Signal name
Throttle position sensor 1
Sensor power supply
(Throttle position sensor)
Power supply for ECM
(Backup)
Intake manifold runner
control valve position sensor
84
(V)
Sensor power supply
(Intake manifold runner
control valve position sensor)
85
(G)
Lin communication line
86
(Y)
Ignition signal No. 1
87
(BR)
Ignition signal No. 2
90
(W)
128
(BR)
91
(SB)
Condition
Input/
Output
Input
Value
(Approx.)
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully released
More than 0.36 V
[Ignition switch: ON]
Engine stopped
Selector lever: D
Accelerator pedal: Fully depressed
Less than 4.75 V
[Ignition switch: ON]
5.0 V
Input
[Ignition switch: OFF]
Battery voltage
(11 - 14 V)
[Ignition switch ON]
Engine coolant temperature: Between -7C (19F) and 60C (140F)
Accelerator pedal: Fully released
Less than 1.4 V
[Ignition switch ON]
Engine coolant temperature: Between -7C (19F) and 60C (140F)
Accelerator pedal: Slightly depressed
More than 2.8 V
Input
[Ignition switch: ON]
Input/
Output
5.0 V
0 - 0.1 V
[Engine is running]
Warm-up condition
Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
JMBIA0085GB
Output
0 - 0.2 V
Ignition signal No. 3
[Engine is running]
Warm-up condition
Engine speed: 2,000 rpm
Ignition signal No. 4
JMBIA0086GB
89
(P)
92
(LG)
128
(BR)
ECM relay
(Self shut-off)
Sensor ground
(Intake manifold runner
control valve position sensor)
Revision: August 2014
Output
[Engine is running]
[Ignition switch: OFF]
A few seconds after turning ignition
switch OFF
0 - 1.0 V
[Ignition switch: OFF]
More than a few seconds after turning ignition switch OFF
Battery voltage
(11 - 14 V)
EC-90
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
+
Description
Signal name
Condition
Input/
Output
[Engine is running]
Warm-up condition
Idle speed
Value
(Approx.)
EC
0V
Battery voltage
(11 - 14 V)
93
(L)
128
(BR)
Intake valve timing control
solenoid valve
Output
[Engine is running]
Warm-up condition
When revving engine up to
2,000rpm Quickly
E
JMBIA1638GB
94
(BR)
128
(BR)
Exhaust valve timing control solenoid valve
Output
[Engine is running]
Warm-up condition
Idle speed
0V
[Engine is running]
Warm-up condition
Engine speed: 2,000 rpm
Battery voltage
(11 - 14 V)
Battery voltage
(11 - 14 V)
97
(GR)
128
(BR)
EVAP canister vent control valve
Output
[Ignition switch: ON]
99
(P)
CAN communication line
(CAN-L)
Input/
Output
100
(L)
CAN communication line
(CAN-H)
Input/
Output
Input
[Engine is running]
Warm-up condition
Both A/C switch and blower fan motor switch: ON (Compressor operates)
1.0 - 4.0 V
103
(Y)
124
(W)
104
(R)
109
(LG)
128
(BR)
110
(G)
111
(BR)
Refrigerant pressure sensor
Sensor power supply
(Refrigerant pressure
sensor)
Ignition switch
ASCD steering switch
Input
Input
[Ignition switch: ON]
5.0 V
[Ignition switch: OFF]
0V
[Ignition switch: ON]
Battery voltage
(11 - 14 V)
[Ignition switch: ON]
ASCD steering switch: OFF
4V
[Ignition switch: ON]
MAIN switch: Pressed
0V
[Ignition switch: ON]
CANCEL switch: Pressed
1V
[Ignition switch: ON]
ACCEL/RES switch: Pressed
3V
[Ignition switch: ON]
COAST/SET switch: Pressed
2V
Sensor ground
(ASCD steering switch)
113
(R)
Sensor power supply
(EVAP control system
pressure sensor)
[Ignition switch: ON]
5.0 V
114
(BR)
124
(W)
EVAP control system
pressure sensor
Input
[Ignition switch: ON]
0.5 - 4.6 V
EC-91
111
(BR)
Revision: August 2014
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Terminal No.
(Wire color)
Description
Input/
Output
115
(V)
128
(BR)
Stop lamp switch
Input
116
(GR)
128
(BR)
Brake pedal position
switch
Input
117
(W)
128
(BR)
118
(SB)
119
(Y)
120
(LG)
120
(LG)
121
(BR)
128
(BR)
122
(V)
123
(BR)
Signal name
PNP signal
Sensor power supply
(Accelerator pedal position sensor 2)
Accelerator pedal position sensor 2
Sensor ground
(Accelerator pedal position sensor 2)
Input
Input
Value
(Approx.)
Condition
[Ignition switch: OFF]
Brake pedal: Fully released
0V
[Ignition switch: OFF]
Brake pedal: Slightly depressed
Battery voltage
(11 - 14 V)
[Ignition switch: OFF]
Brake pedal: Fully released
Battery voltage
(11 - 14 V)
[Ignition switch: ON]
Selector lever: P or N
Battery voltage
(11 - 14 V)
[Ignition switch: ON]
Selector lever: Except above
0V
[Ignition switch: ON]
5.0 V
[Ignition switch: ON]
Engine stopped
Accelerator pedal: Fully released
0.25 - 0.5 V
[Ignition switch: ON]
Engine stopped
Accelerator pedal: Fully depressed
2.0 - 2.5 V
Input
[Ignition switch: ON]
Battery voltage
(11 - 14 V)
Sensor power supply
(Accelerator pedal position sensor 1)
[Ignition switch: ON]
5.0 V
ECM ground
124
(W)
Sensor ground
(EVAP control system
pressure sensor, refrigerant pressure sensor)
125
(BG)
128
(BR)
126
(GR)
127
(L)
Power supply for ECM
Fuel tank temperature
sensor
Accelerator pedal position sensor 1
Input
Input
[Engine is running]
0 - 4.8 V
Output voltage varies with fuel
tank temperature
[Ignition switch: ON]
Engine stopped
Accelerator pedal: Fully released
0.5 - 1.0 V
[Ignition switch: ON]
Engine stopped
Accelerator pedal: Fully depressed
4.2 - 4.8 V
127
(R)
Sensor ground
(Accelerator pedal position sensor 1)
128
(BR)
ECM ground
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Fail Safe
INFOID:0000000011277887
NON DTC RELATED ITEM
Revision: August 2014
EC-92
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Detected
items
Engine operating condition
in fail-safe mode
Malfunction
indicator
lamp circuit
Engine speed will not rise
more than 2,500 rpm due
to the fuel cut
Remarks
Reference page
When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by lighting up MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating fail safe function.
The fail safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction.
EC
EC-479, "Component Function
Check"
DTC RELATED ITEM
Description
When a DTC is detected, ECM executes a mode (in the Fail-safe mode) applicable to the DTC. The fail-safe
mode has the preset traveling control mode (accelerator angle variation and engine output limit) and device fix
mode.
Fail safe mode
Traveling control mode
Vehicle behavior
Accelerator angle variation
control
ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Engine output
control
ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle
speed to encourage the driver to repair malfunction.
This mode fixes the IVT control solenoid valve and the EVT control solenoid valve in the reference position.
The intake manifold runner control valve motor is turned OFF (intake manifold runner control
valve opens).
Device fix mode
Fail Safe Pattern
J
Pattern
A
Fail safe mode
Accelerator angle variation control
Traveling control mode
B
C
Engine output control
Device fix mode
Fail Safe List
:Applicable : Not applicable
Vehicle behavior
DTC
No.
P0011
Detected items
Pattern
A
ECM activates the IVT intermediate lock control solenoid
valve to bring the cam sprocket into an intermediate lock condition.
Intake valve timing control
P0014
P0078
Exhaust valve timing control
P0101
P0102
P0103
Mass air flow sensor circuit
P0122
P0123
P0222
P0223
P2135
Throttle position sensor
Revision: August 2014
M
Others
EC-93
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Vehicle behavior
DTC
No.
Detected items
Pattern
Others
P0171
P0172
Fuel injection system
P0197
P0198
Engine oil temperature sensor
P0300
P0301
P0302
P0303
P0304
Misfire
P0500
Vehicle speed sensor
P050A
Cold start control
P0524
Engine oil pressure
P052A
P052B
Intake valve timing intermediate lock control
P0603
ECM
P0604
ECM
P0605
P060B
ECM
P0606
ECM
P0607
ECM
Exhaust valve timing control does not function.
ECM illuminates oil pressure warning lamp on the combination meter.
Engine speed will not rise more than 4,000rpm due to the
fuel cut.
Fail-safe is canceled when ignition switch OFF ON.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
ASCD operation may be deactivated.
P060A
ECM
P0643
ECM
P1078
Exhaust valve timing control
position sensor circuit
P1568
Signal invalid
P1805
Brake switch
Intake manifold runner control
valve
P2100
P2103
Throttle control motor relay
P2101
Electric throttle control function
Revision: August 2014
Active trace control does not function.
ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
P2004
ASCD operation may be deactivated.
Vehicle condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
EC-94
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Vehicle behavior
DTC
No.
P2118
Detected items
Pattern
A
ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
EC
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
Throttle control motor
P2119
Electric throttle control actuator
P2122
P2123
P2127
P2128
P2138
Accelerator pedal position
sensor
A
Others
DTC Inspection Priority Chart
INFOID:0000000011277888
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority
DTC
Detected items
U0101, U1001
CAN communication line
P0101, P0102, P0103
Mass air flow sensor
P0111, P0112, P0113, P0127
Intake air temperature sensor
P0116, P0117, P0118, P0125
Engine coolant temperature sensor
P0122, P0123, P0222, P0223, P1225, P1226, P2135
Throttle position sensor
P0128
Thermostat function
P0181, P0182, P0183
Fuel tank temperature sensor
P0196, P0197, P0198
Engine oil temperature sensor
P0327, P0328
Knock sensor
P0335
Crankshaft position sensor (POS)
P0340
Camshaft position sensor (PHASE)
P0460, P0461, P0462, P0463
Fuel level sensor
P0500
Vehicle speed sensor
P0520
Engine oil pressure sensor
P0603, P0604, P0605, P0606, P0607, P060A, P060B,
P2610
ECM
P0643
Sensor power supply
P0850
Transmission range switch
P1078
Exhaust valve timing control position sensor
P1610, P1611, P1612, P1615
NATS
P2014, P2016, P2017, P2018
Intake manifold runner control valve position sensor
P2122, P2123, P2127, P2128, P2138
Accelerator pedal position sensor
Revision: August 2014
EC-95
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Priority
DTC
Detected items
P0030, P0031, P0032
Air fuel ratio (A/F) sensor 1 heater
P0037, P0038
Heated oxygen sensor 2 heater
P0075
Intake valve timing control solenoid valve/Intake valve timing
intermediate lock control solenoid valve
P0078
Exhaust valve timing control solenoid valve
P0130, P0131, P0132, P014C, P014D, P015A, P015B,
P117A, P2096, P2097
Air fuel ratio (A/F) sensor 1
P0137, P0138, P0139
Heated oxygen sensor 2
P0441
EVAP control system purge flow monitoring
P0443, P0444, P0445
EVAP canister purge volume control solenoid valve
P0447, P0448
EVAP canister vent control valve
P0451, P0452, P0453
EVAP control system pressure sensor
P1217
Engine over temperature (OVERHEAT)
P1805
Brake switch
P2004
Intake manifold runner control valve
P2100, P2103
Throttle control motor relay
P2101
Electric throttle control function
P2118
Throttle control motor
P0011, P052A, P052B
Intake valve timing control
P0014
Exhaust valve timing control
P0171, P0172
Fuel injection system function
P0300, P0301, P0302, P0303, P0304
Misfire
P0420
Three way catalyst function
P0456
EVAP control system
P0506, P0507
Idle speed control system
P050A, P050B, P050E
Cold start control
P0524
Engine oil pressure
P1148
Closed loop control
P1212
TCS communication line
P1564
ASCD steering switch
P1572
ASCD brake switch
P1574
ASCD vehicle speed sensor
P1715
Input speed sensor
P2119
Electric throttle control actuator
DTC Index
INFOID:0000000011277889
:Applicable : Not applicable
DTC*1
CONSULT
GST*2
Items
(CONSULT screen terms)
ECM*3
SRT
code
Trip
MIL
Permanent
DTC group*4
Reference
page
U0101
0101*5
LOST COMM (TCM)
EC-172
U1001
1001*5
CAN COMM CIRCUIT
2 or 1
EC-173
U1040
1040*5
ENG COMM CIRCUIT
EC-174
U1044
1044*5
ENG COMM CIRCUIT
EC-176
Revision: August 2014
EC-96
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
DTC*1
CONSULT
GST*2
Items
(CONSULT screen terms)
ECM*3
SRT
code
Trip
MIL
Reference
page
DTC group*4
EC
Permanent
U1050
1050*5
LIN COMMUNICATION
EC-178
U1051
1051*5
LIN COMMUNICATION
EC-178
P0000
0000
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.
Flashing*6
P0011
0011
INT/V TIM CONT-B1
EC-180
P0014
0014
EXH/V TIM CONT-B1
EC-184
P0030
0030
A/F SEN1 HTR (B1)
EC-188
P0031
0031
A/F SEN1 HTR (B1)
EC-188
P0032
0032
A/F SEN1 HTR (B1)
EC-188
P0037
0037
HO2S2 HTR (B1)
EC-191
P0038
0038
HO2S2 HTR (B1)
EC-191
P0075
0075
INT/V TIM V/CIR-B1
EC-194
P0078
0078
EX V/T ACT/CIRC-B1
EC-198
P0101
0101
MAF SEN/CIRCUIT-B1
EC-201
P0102
0102
MAF SEN/CIRCUIT-B1
EC-205
P0103
0103
MAF SEN/CIRCUIT-B1
EC-205
P0111
0111
IAT SENSOR 1 B1
EC-209
P0112
0112
IAT SEN/CIRCUIT-B1
EC-211
P0113
0113
IAT SEN/CIRCUIT-B1
EC-211
P0116
0116
ECT SENSOR
EC-214
P0117
0117
ECT SEN/CIRC
EC-216
P0118
0118
ECT SEN/CIRC
EC-216
P0122
0122
TP SEN 2/CIRC-B1
EC-219
P0123
0123
TP SEN 2/CIRC-B1
EC-219
P0125
0125
ECT SENSOR
EC-222
P0127
0127
IAT SENSOR-B1
EC-224
P0128
0128
THERMSTAT FNCTN
EC-226
P0130
0130
A/F SENSOR1 (B1)
EC-229
P0131
0131
A/F SENSOR1 (B1)
EC-233
P0132
0132
A/F SENSOR1 (B1)
EC-236
P0137
0137
HO2S2 (B1)
EC-239
P0138
0138
HO2S2 (B1)
EC-245
P0139
0139
HO2S2 (B1)
EC-252
P014C
014C
A/F SENSOR1 (B1)
EC-258
P014D
014D
A/F SENSOR1 (B1)
EC-258
P015A
015A
A/F SENSOR1 (B1)
EC-258
P015B
015B
A/F SENSOR1 (B1)
EC-258
P0171
0171
FUEL SYS-LEAN-B1
EC-263
P0172
0172
FUEL SYS-RICH-B1
EC-268
P0181
0181
FTT SENSOR
A and B
EC-273
P0182
0182
FTT SEN/CIRCUIT
EC-277
P0183
0183
FTT SEN/CIRCUIT
EC-277
Revision: August 2014
EC-97
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
DTC*1
CONSULT
GST*2
Items
(CONSULT screen terms)
ECM*3
SRT
code
Trip
MIL
Permanent
DTC group*4
Reference
page
P0196
0196
EOT SENSOR
A and B
EC-280
P0197
0197
EOT SEN/CIRC
EC-284
P0198
0198
EOT SEN/CIRC
EC-284
P0222
0222
TP SEN 1/CIRC-B1
EC-287
P0223
0223
TP SEN 1/CIRC-B1
EC-287
P0300
0300
MULTI CYL MISFIRE
1 or 2
EC-290
P0301
0301
CYL 1 MISFIRE
1 or 2
EC-290
P0302
0302
CYL 2 MISFIRE
1 or 2
EC-290
P0303
0303
CYL 3 MISFIRE
1 or 2
EC-290
P0304
0304
CYL 4 MISFIRE
1 or 2
EC-290
P0327
0327
KNOCK SEN/CIRC-B1
EC-296
P0328
0328
KNOCK SEN/CIRC-B1
EC-296
P0335
0335
CKP SEN/CIRCUIT
EC-298
P0340
0340
CMP SEN/CIRC-B1
EC-301
P0420
0420
TW CATALYST SYS-B1
EC-304
P0441
0441
EVAP PURG FLOW/MON
EC-309
P0443
0443
PURG VOLUME CONT/V
EC-314
P0444
0444
PURG VOLUME CONT/V
EC-319
P0445
0445
PURG VOLUME CONT/V
EC-319
P0447
0447
VENT CONTROL VALVE
EC-322
P0448
0448
VENT CONTROL VALVE
EC-326
P0451
0451
EVAP SYS PRES SEN
EC-330
P0452
0452
EVAP SYS PRES SEN
EC-334
P0453
0453
EVAP SYS PRES SEN
EC-337
EC-341
P0456
0456
EVAP VERY SML LEAK
P0460
0460
FUEL LEV SEN SLOSH
EC-347
P0461
0461
FUEL LEVEL SENSOR
EC-349
P0462
0462
FUEL LEVL SEN/CIRC
EC-351
P0463
0463
FUEL LEVL SEN/CIRC
EC-351
EC-353
A*8
P0500
0500
VEHICLE SPEED SENSOR
P0506
0506
ISC SYSTEM
EC-355
P0507
0507
ISC SYSTEM
EC-357
P050A
050A
COLD START CONTROL
EC-359
P050B
050B
COLD START CONTROL
EC-359
P050E
050E
COLD START CONTROL
EC-359
P0520
0520
EOP SENSOR/SWITCH
EC-361
P0524
0524
ENGINE OIL PRESSURE
EC-364
P052A
052A
CAMSHAFT POSITION TIMING B1
EC-367
P052B
052B
CAMSHAFT POSITION TIMING B1
EC-367
or
EC-373
UP/CIRCUIT*9
P0603
0603
ECM BACK
P0604
0604
ECM
EC-375
P0605
0605
ECM
1 or 2
or
EC-376
Revision: August 2014
EC-98
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
DTC*1
CONSULT
GST*2
Items
(CONSULT screen terms)
ECM*3
SRT
code
Trip
MIL
Reference
page
DTC group*4
EC
Permanent
P0606
0606
CONTROL MODULE
or
EC-377
P0607
0607
ECM
1 or 2
or
EC-379
P060A
060A
CONTROL MODULE
1 or 2
EC-380
P060B
060B
CONTROL MODULE
EC-381
P062F
062F
CONTROL MODULE
EC-373
P0643
0643
SENSOR POWER/CIRC
EC-382
P0850
0850
P-N POS SW/CIRCUIT
EC-385
P1078
1078
EXH TIM SEN/CIRC-B1
EC-388
P1148
1148
CLOSED LOOP-B1
EC-391
P117A
117A
AIR FUEL RATIO B1
EC-392
P1212
1212
TCS/CIRC
EC-398
P1217
1217
ENG OVER TEMP
EC-400
P1225
1225
CTP LEARNING-B1
EC-403
P1226
1226
CTP LEARNING-B1
EC-404
P155D
155D
GENERATOR
EC-405
P1564
1564
ASCD SW
EC-406
P1568
1568
ICC COMMAND VALUE
EC-409
P1572
1572
ASCD BRAKE SW
EC-411
P1574
1574
ASCD VHL SPD SEN
EC-417
P1610
1610
LOCK MODE
SEC-68,
SEC-161
P1611
1611
ID DISCORD,IMMU-ECM
SEC-69,
SEC-162
P1612
1612
CHAIN OF ECM-IMMU
SEC-70,
SEC-163
P161D
161D
IMMOBILIZER
SEC-71,
SEC-164
P161E
161E
IMMOBILIZER
SEC-72,
SEC-165
P161F
161F
IMMOBILIZER
SEC-73,
SEC-166
P1715
1715
IN PULY SPEED
EC-419
P1805
1805
BRAKE SW/CIRCUIT
EC-421
P2004
2004
TUMBLE CONT/V
EC-423
P2014
2014
IN/MANIFOLD RUNNER POS SEN B1
EC-426
P2016
2016
IN/MANIFOLD RUNNER POS SEN B1
EC-426
P2017
2017
IN/MANIFOLD RUNNER POS SEN B1
EC-426
P2018
2018
IN/MANIFOLD RUNNER POS SEN B1
EC-426
P2096
2096
POST CATALYST FUEL TRIM SYS B1
EC-429
P2097
2097
POST CATALYST FUEL TRIM SYS B1
EC-429
P2100
2100
ETC MOT PWR-B1
EC-433
P2101
2101
ETC FNCTN/CIRC-B1
EC-436
P2103
2103
ETC MOT PWR-B1
EC-433
P2118
2118
ETC MOT-B1
EC-439
Revision: August 2014
EC-99
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
DTC*1
CONSULT
GST*2
Items
(CONSULT screen terms)
ECM*3
SRT
code
Trip
MIL
Permanent
DTC group*4
Reference
page
P2119
2119
ETC ACTR-B1
EC-441
P2122
2122
APP SEN 1/CIRC
EC-443
P2123
2123
APP SEN 1/CIRC
EC-443
P2127
2127
APP SEN 2/CIRC
EC-446
P2128
2128
APP SEN 2/CIRC
EC-446
P2135
2135
TP SENSOR-B1
EC-449
P2138
2138
APP SENSOR
EC-452
P2610
2610
ECM/PCM INTERNAL ENG OFF TIMER
A and B
EC-456
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J1979/ ISO 15031-5.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: Refer to EC-154, "Description".
*5: The troubleshooting for this DTC needs CONSULT.
*6: When the ECM is in the mode that displays SRT status, MIL may blink. For details, Refer to EC-66, "On Board Diagnosis Function".
*7: SRT code will not be set if the self-diagnostic result is NG.
*8: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
*9: This self-diagnosis is not for ECM power supply circuit, even though ECM BACK UP/CIRCUIT is displayed on CONSULT screen.
Test Value and Test Limit
INFOID:0000000011518225
The following is the information specified in Service $06 of SAE J1979/ISO 15031-5.
The test value is a parameter used to determine whether a system/circuit diagnostic test is OK or NG while
being monitored by the ECM during self-diagnosis. The test limit is a reference value which is specified as the
maximum or minimum value and is compared with the test value being monitored.
These data (test value and test limit) are specified by On Board Monitor ID (OBDMID), Test ID (TID), Unit and
Scaling ID and can be displayed on the GST screen.
The items of the test value and test limit will be displayed with GST screen which items are provided by the
ECM. (e.g., if bank 2 is not applied on this vehicle, only the items of bank 1 are displayed)
Revision: August 2014
EC-100
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
HO2S
OBDMID
01H
Self-diagnostic test item
Air fuel ratio (A/F) sensor 1
(Bank 1)
DTC
Test value and Test
limit
(GST display)
A
Description
TID
Unit and
Scaling
ID
P0131
83H
0BH
Minimum sensor output voltage for test
cycle
P0131
84H
0BH
Maximum sensor output voltage for
test cycle
P0130
85H
0BH
Minimum sensor output voltage for test
cycle
P0130
86H
0BH
Maximum sensor output voltage for
test cycle
P0133
87H
04H
Response rate: Response ratio (lean
to rich)
P0133
88H
04H
Response rate: Response ratio (rich to
lean)
P2A00 or P2096
89H
84H
The amount of shift in air fuel ratio (too
lean)
P2A00 or P2097
8AH
84H
The amount of shift in air fuel ratio (too
rich)
P0130
8BH
0BH
Difference in sensor output voltage
P0133
8CH
83H
Response gain at the limited frequency
P014C
8DH
04H
O2 sensor slow response - Rich to
lean bank 1 sensor 1
P014C
8EH
04H
O2 sensor slow response - Rich to
lean bank 1 sensor 1
P014D
8FH
84H
O2 sensor slow response - Lean to rich
bank 1 sensor 1
P014D
90H
84H
O2 sensor slow response - Lean to rich
bank 1 sensor 1
P015A
91H
01H
O2 sensor delayed response - Rich to
lean bank 1 sensor 1
P015A
92H
01H
O2 sensor delayed response - Rich to
lean bank 1 sensor 1
P015B
93H
01H
O2 sensor delayed response - Lean to
rich bank 1 sensor 1
EC
P015B
94H
01H
O2 sensor delayed response - Lean to
rich bank 1 sensor 1
P0133
95H
04H
Response rate: Response ratio (lean
to rich)
P0133
96H
84H
Response rate: Response ratio (rich to
lean)
Revision: August 2014
EC-101
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
OBDMID
02H
03H
Self-diagnostic test item
Heated oxygen sensor 2
(Bank 1)
Heated oxygen sensor 3
(Bank 1)
HO2S
05H
Air fuel ratio (A/F) sensor 1
(Bank 2)
Revision: August 2014
DTC
Test value and Test
limit
(GST display)
Description
TID
Unit and
Scaling
ID
P0138
07H
0CH
Minimum sensor output voltage for test
cycle
P0137
08H
0CH
Maximum sensor output voltage for
test cycle
P0138
80H
0CH
Sensor output voltage
P0139
81H
0CH
Difference in sensor output voltage
P0139
82H
11H
Rear O2 sensor delay response diagnosis
P0143
07H
0CH
Minimum sensor output voltage for test
cycle
P0144
08H
0CH
Maximum sensor output voltage for
test cycle
P0146
80H
0CH
Sensor output voltage
P0145
81H
0CH
Difference in sensor output voltage
P0151
83H
0BH
Minimum sensor output voltage for test
cycle
P0151
84H
0BH
Maximum sensor output voltage for
test cycle
P0150
85H
0BH
Minimum sensor output voltage for test
cycle
P0150
86H
0BH
Maximum sensor output voltage for
test cycle
P0153
87H
04H
Response rate: Response ratio (lean
to rich)
P0153
88H
04H
Response rate: Response ratio (rich to
lean)
P2A03 or P2098
89H
84H
The amount of shift in air fuel ratio (too
lean)
P2A03 or P2099
8AH
84H
The amount of shift in air fuel ratio (too
rich)
P0150
8BH
0BH
Difference in sensor output voltage
P0153
8CH
83H
Response gain at the limited frequency
P014E
8DH
04H
O2 sensor slow response - Rich to
lean bank 2 sensor 1
P014E
8EH
04H
O2 sensor slow response - Rich to
lean bank 2 sensor 1
P014F
8FH
84H
O2 sensor slow response - Lean to rich
bank 2 sensor 1
P014F
90H
84H
O2 sensor slow response - Lean to rich
bank 2 sensor 1
P015C
91H
01H
O2 sensor delayed response - Rich to
lean bank 2 sensor 1
P015C
92H
01H
O2 sensor delayed response - Rich to
lean bank 2 sensor 1
P015D
93H
01H
O2 sensor delayed response - Lean to
rich bank 2 sensor 1
EC-102
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
OBDMID
Self-diagnostic test item
DTC
P015D
05H
HO2S
06H
07H
21H
Air fuel ratio (A/F) sensor 1
(Bank 2)
Heated oxygen sensor 2
(Bank 2)
Heated oxygen sensor 3
(Bank2)
Three way catalyst function
(Bank1)
CATALYST
22H
EGR
SYSTEM
31H
Three way catalyst function
(Bank2)
EGR function
Revision: August 2014
Test value and Test
limit
(GST display)
A
Description
TID
Unit and
Scaling
ID
94H
01H
O2 sensor delayed response - Lean to
rich bank 2 sensor 1
EC
P0153
95H
04H
Response rate: Response ratio (lean
to rich)
P0153
96H
84H
Response rate: Response ratio (rich to
lean)
P0158
07H
0CH
Minimum sensor output voltage for test
cycle
P0157
08H
0CH
Maximum sensor output voltage for
test cycle
P0158
80H
0CH
Sensor output voltage
P0159
81H
0CH
Difference in sensor output voltage
P0159
82H
11H
Rear O2 sensor delay response diagnosis
P0163
07H
0CH
Minimum sensor output voltage for test
cycle
P0164
08H
0CH
Maximum sensor output voltage for
test cycle
P0166
80H
0CH
Sensor output voltage
P0165
81H
0CH
Difference in sensor output voltage
P0420
80H
01H
O2 storage index
P0420
82H
01H
Switching time lag engine exhaust index value
P2423
83H
0CH
Difference in 3rd O2 sensor output
voltage
P2423
84H
84H
O2 storage index in HC trap catalyst
P0430
80H
01H
O2 storage index
P0430
82H
01H
Switching time lag engine exhaust index value
P2424
83H
0CH
Difference in 3rd O2 sensor output
voltage
P2424
84H
84H
O2 storage index in HC trap catalyst
P0400
80H
96H
Low flow faults: EGR temp change rate
(short term)
P0400
81H
96H
Low flow faults: EGR temp change rate
(long term)
P0400
82H
96H
Low flow faults: Difference between
max EGR temp and EGR temp under
idling condition
P0400
83H
96H
Low flow faults: Max EGR temp
P1402
84H
96H
High Flow Faults: EGR temp increase
rate
P0402
85H
FCH
EGR differential pressure high flow
P0401
86H
37H
EGR differential pressure low flow
P2457
87H
96H
EGR temperature
EC-103
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
OBDMID
35H
Self-diagnostic test item
VVT Monitor (Bank1)
VVT
SYSTEM
36H
EVAP
SYSTEM
VVT Monitor (Bank2)
DTC
Test value and Test
limit
(GST display)
Description
TID
Unit and
Scaling
ID
P0011
80H
9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0014
81H
9DH
VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0011
82H
9DH
VTC intake function diagnosis (VTC
drive failure diagnosis)
P0014
83H
9DH
VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100A
84H
10H
VEL slow response diagnosis
P1090
85H
10H
VEL servo system diagnosis
P0011
86H
9DH
VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052A
Retarded: P052B
87H
9DH
VTC intake intermediate lock system
diagnosis (VTC intermediate lock position check diagnosis)
P0021
80H
9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0024
81H
9DH
VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0021
82H
9DH
VTC intake function diagnosis (VTC
drive failure diagnosis)
P0024
83H
9DH
VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100B
84H
10H
VEL slow response diagnosis
P1093
85H
10H
VEL servo system diagnosis
P0021
86H
9DH
VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052C
Retarded: P052D
87H
9DH
VTC intake intermediate lock system
diagnosis (VTC intermediate lock position check diagnosis)
39H
EVAP control system leak
(Cap Off)
P0455
80H
0CH
Difference in pressure sensor output
voltage before and after pull down
3BH
EVAP control system leak
(Small leak)
P0442
80H
05H
Leak area index (for more than 0.04
inch)
P0456
80H
05H
Leak area index (for more than 0.02
inch)
P0456
81H
FDH
Maximum internal pressure of EVAP
system during monitoring
P0456
82H
FDH
Internal pressure of EVAP system at
the end of monitoring
P0441
83H
0CH
Difference in pressure sensor output
voltage before and after vent control
valve close
3CH
3DH
EVAP control system leak
(Very small leak)
Purge flow system
Revision: August 2014
EC-104
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
OBDMID
41H
42H
O2 SENSOR
HEATER
A/F sensor 1 heater (Bank 1)
Heated oxygen sensor 2 heater (Bank 1)
43H
Heated oxygen sensor 3 heater (Bank 1)
45H
A/F sensor 1 heater (Bank 2)
46H
47H
SECONDARY AIR
Self-diagnostic test item
71H
81H
Heated oxygen sensor 2 heater (Bank 2)
Heated oxygen sensor 3 heater (Bank 2)
Secondary air system
Fuel injection system function
(Bank 1)
FUEL
SYSTEM
82H
Fuel injection system function
(Bank 2)
DTC
Test value and Test
limit
(GST display)
A
Description
TID
Unit and
Scaling
ID
Low Input: P0031
High Input: P0032
81H
0BH
Converted value of heater electric current to voltage
P0030
83H
0BH
A/F sensor heater circuit malfunction
Low Input: P0037
High Input: P0038
80H
0CH
Converted value of heater electric current to voltage
P0141
81H
14H
Rear O2 sensor internal impedance
P0043
80H
0CH
Converted value of heater electric current to voltage
Low Input: P0051
High Input: P0052
81H
0BH
Converted value of heater electric current to voltage
P0036
83H
0BH
A/F sensor heater circuit malfunction
Low Input: P0057
High Input: P0058
80H
0CH
Converted value of heater electric current to voltage
P0161
81H
14CH
Rear O2 sensor internal impedance
P0063
80H
0CH
Converted value of heater electric current to voltage
P0411
80H
01H
Secondary air injection system incorrect flow detected
Bank1: P0491
Bank2: P0492
81H
01H
Secondary air injection system insufficient flow
P2445
82H
01H
Secondary air injection system pump
stuck off
P2448
83H
01H
Secondary air injection system high
airflow
Bank1: P2440
Bank2: P2442
84H
01H
Secondary air injection system switching valve stuck open
EC
P2440
85H
01H
Secondary air injection system switching valve stuck open
P2444
86H
01H
Secondary air injection system pump
stuck on
P0171 or P0172
80H
2FH
Long term fuel trim
P0171 or P0172
81H
24H
The number of lambda control
clamped
P117A / P219A
82H
03H
Cylinder A/F imbalance monitoring
P0174 or P0175
80H
2FH
Long term fuel trim
P0174 or P0175
81H
24H
The number of lambda control
clamped
P117B / P219B
82H
03H
Cylinder A/F imbalance monitoring
Revision: August 2014
EC-105
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
MISFIRE
OBDMID
A1H
Self-diagnostic test item
DTC
Test value and Test
limit
(GST display)
TID
P0301
80H
24H
Misfiring counter at 1000 revolution of
the first cylinder
P0302
81H
24H
Misfiring counter at 1000 revolution of
the second cylinder
P0303
82H
24H
Misfiring counter at 1000 revolution of
the third cylinder
P0304
83H
24H
Misfiring counter at 1000 revolution of
the fourth cylinder
P0305
84H
24H
Misfiring counter at 1000 revolution of
the fifth cylinder
P0306
85H
24H
Misfiring counter at 1000 revolution of
the sixth cylinder
P0307
86H
24H
Misfiring counter at 1000 revolution of
the seventh cylinder
P0308
87H
24H
Misfiring counter at 1000 revolution of
the eighth cylinder
P0300
88H
24H
Misfiring counter at 1000 revolution of
the multiple cylinders
P0301
89H
24H
Misfiring counter at 200 revolution of
the first cylinder
P0302
8AH
24H
Misfiring counter at 200 revolution of
the second cylinder
P0303
8BH
24H
Misfiring counter at 200 revolution of
the third cylinder
P0304
8CH
24H
Misfiring counter at 200 revolution of
the fourth cylinder
P0305
8DH
24H
Misfiring counter at 200 revolution of
the fifth cylinder
P0306
8EH
24H
Misfiring counter at 200 revolution of
the sixth cylinder
P0307
8FH
24H
Misfiring counter at 200 revolution of
the seventh cylinder
P0308
90H
24H
Misfiring counter at 200 revolution of
the eighth cylinder
P0300
91H
24H
Misfiring counter at 1000 revolution of
the single cylinder
P0300
92H
24H
Misfiring counter at 200 revolution of
the single cylinder
P0300
93H
24H
Misfiring counter at 200 revolution of
the multiple cylinders
Multiple cylinder misfires
Revision: August 2014
Description
Unit and
Scaling
ID
EC-106
2015 Rogue NAM
ECM
[QR25DE]
< ECU DIAGNOSIS INFORMATION >
Item
OBDMID
A2H
A3H
A4H
Self-diagnostic test item
DTC
A7H
A8H
A9H
Description
TID
P0301
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0301
0CH
24H
Misfire counts for last/current driving
cycles
No. 1 cylinder misfire
EC
P0302
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0302
0CH
24H
Misfire counts for last/current driving
cycles
P0303
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0303
0CH
24H
Misfire counts for last/current driving
cycles
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
No. 2 cylinder misfire
No. 3 cylinder misfire
0BH
No. 4 cylinder misfire
P0304
0CH
24H
Misfire counts for last/current driving
cycles
P0305
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0305
0CH
24H
Misfire counts for last/current driving
cycles
P0306
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
MISFIRE
A6H
Unit and
Scaling
ID
P0304
A5H
Test value and Test
limit
(GST display)
No. 5 cylinder misfire
No. 6 cylinder misfire
P0306
0CH
24H
Misfire counts for last/current driving
cycles
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0307
P0307
0CH
24H
Misfire counts for last/current driving
cycles
P0308
0BH
24H
EWMA (Exponential Weighted Moving
Average) misfire counts for last 10 driving cycles
P0308
0CH
24H
Misfire counts for last/current driving
cycles
No. 7 cylinder misfire
No. 8 cylinder misfire
Revision: August 2014
EC-107
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
WIRING DIAGRAM
ENGINE CONTROL SYSTEM
Wiring Diagram
INFOID:0000000011277891
AABWA0953GB
Revision: August 2014
EC-108
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABWA0954GB
Revision: August 2014
EC-109
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABWA0955GB
Revision: August 2014
EC-110
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABWA0956GB
Revision: August 2014
EC-111
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABWA0957GB
Revision: August 2014
EC-112
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABWA0855GB
Revision: August 2014
EC-113
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABWA0856GB
Revision: August 2014
EC-114
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1437GB
Revision: August 2014
EC-115
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1438GB
Revision: August 2014
EC-116
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1439GB
Revision: August 2014
EC-117
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1206GB
Revision: August 2014
EC-118
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1440GB
Revision: August 2014
EC-119
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1441GB
Revision: August 2014
EC-120
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1442GB
Revision: August 2014
EC-121
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1443GB
Revision: August 2014
EC-122
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1444GB
Revision: August 2014
EC-123
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1445GB
Revision: August 2014
EC-124
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1446GB
Revision: August 2014
EC-125
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1214GB
Revision: August 2014
EC-126
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1215GB
Revision: August 2014
EC-127
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
AABIA1216GB
Revision: August 2014
EC-128
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< WIRING DIAGRAM >
EC
O
AABIA1217GB
Revision: August 2014
EC-129
2015 Rogue NAM
DIAGNOSIS AND REPAIR WORKFLOW
[QR25DE]
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000011277892
OVERALL SEQUENCE
JSBIA0123GB
DETAILED FLOW
Revision: August 2014
EC-130
2015 Rogue NAM
DIAGNOSIS AND REPAIR WORKFLOW
[QR25DE]
< BASIC INSPECTION >
1.GET INFORMATION FOR SYMPTOM
1.
2.
A
Get the detailed information from the customer about the symptom (the condition and the environment
when the incident/malfunction occurred) using the Diagnostic Work Sheet. (Refer to EC-133, "Diagnostic
Work Sheet".)
EC
Ask if the customer requests I/M examination.
Malfunction information, obtained>>GO TO 2.
No malfunction information, but a request for I/M examination>>GO TO 13.
2.CHECK DTC
1.
2.
-
Check DTC.
Perform the following procedure if DTC is displayed.
Record DTC and freeze frame data. (Print them out with CONSULT or GST.)
Erase only DTC of ENGINE.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
(Symptom Matrix Chart is useful. Refer to EC-489, "Symptom Table".)
3. Check related service bulletins for information.
Are any symptoms described and any DTCs detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer (except MIL ON).
Also study the normal operation and fail-safe related to the symptom. Refer to EC-495, "Description" and EC92, "Fail Safe".
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom. Refer to Refer to EC-495, "Description"
and EC-92, "Fail Safe".
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then check that DTC is detected
again.
If two or more DTCs are detected, refer to EC-95, "DTC Inspection Priority Chart" and determine trouble
diagnosis order.
NOTE:
Freeze frame data is useful if the DTC is not detected.
Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIRMATION PROCEDURE.
Is DTC detected?
YES >> GO TO 10.
NO
>> Check according to GI-44, "Intermittent Incident".
6.PERFORM BASIC INSPECTION
Perform EC-135, "Work Procedure".
Revision: August 2014
EC-131
2015 Rogue NAM
DIAGNOSIS AND REPAIR WORKFLOW
[QR25DE]
< BASIC INSPECTION >
Do you have CONSULT?
YES >> GO TO 7.
NO
>> GO TO 9.
7.PERFORM SPEC IN DATA MONITOR MODE
With CONSULT
Check that MASS AIR FLOW SENSOR (Hz), B/FUEL SCHDL, and A/F ALPHA-B1 are within the SP
value using SPEC in DATA MONITOR mode with CONSULT. Refer to EC-160, "Component Function
Check".
Is the measurement value within the SP value?
YES >> GO TO 9.
NO
>> GO TO 8.
8.DETECT MALFUNCTIONING PART BY TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Detect malfunctioning part according to EC-161, "Diagnosis Procedure".
Is a malfunctioning part detected?
YES >> GO TO 11.
NO
>> GO TO 9.
9.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to EC-489, "Symptom Table" based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptoms.
>> GO TO 10.
10.DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
NOTE:
The Diagnosis Procedure in EC section described based on open circuit inspection. A short circuit inspection
is also required for the circuit check in the Diagnosis Procedure. For details, refer to GI-46, "Circuit Inspection".
Is a malfunctioning part detected?
YES >> GO TO 11.
NO
>> Monitor input data from related sensors or check voltage of related ECM terminals using CONSULT. Refer to EC-80, "Reference Value".
11.REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
2.
3.
Repair or replace the malfunctioning part.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
Check DTC. If DTC is displayed, erase it.
>> GO TO 12.
12.FINAL CHECK
When DTC was detected in step 2, perform DTC CONFIRMATION PROCEDURE or Component Function
Check again, and then check that the malfunction have been completely repaired.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 10.
YES-2 >> Symptom remains: GO TO 6.
NO-1 >> No request for I/M examination from the customer: Before returning the vehicle to the customer,
always erase unnecessary DTC in ECM. If the completion of SRT is needed, drive vehicle under
the specific driving pattern. Refer to EC-149, "SRT Set Driving Pattern".
NO-2 >> I/M examination, requested from the customer: GO TO 13.
13.PREPARE FOR I/M EXAMINATION
Revision: August 2014
EC-132
2015 Rogue NAM
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
1. Set SRT codes. Refer to EC-148, "Description".
2. Erase permanent DTCs. Refer to EC-154, "Description".
[QR25DE]
A
>> INSPECTION END
EC
Diagnostic Work Sheet
INFOID:0000000011277893
DESCRIPTION
There are many operating conditions that lead to the malfunction of
engine components. A good grasp of such conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about symptoms. It is
important to fully understand the symptoms or conditions for a customer complaint.
Utilize a diagnostic worksheet like the WORKSHEET SAMPLE
below in order to organize all the information for troubleshooting.
Some conditions may cause the MIL to illuminate or blink, and DTC
to be detected. Examples:
Vehicle ran out of fuel, which caused the engine to misfire.
Fuel filler cap was left off or incorrectly screwed on, allowing fuel to
evaporate into the atmosphere.
F
SEF907L
Revision: August 2014
EC-133
2015 Rogue NAM
DIAGNOSIS AND REPAIR WORKFLOW
[QR25DE]
< BASIC INSPECTION >
WORKSHEET SAMPLE
MTBL0017
Revision: August 2014
EC-134
2015 Rogue NAM
BASIC INSPECTION
[QR25DE]
< BASIC INSPECTION >
BASIC INSPECTION
Work Procedure
INFOID:0000000011277894
1.INSPECTION START
1.
2.
3.
4.
EC
Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
Open engine hood and check the following:
Harness connectors for improper connections
Wiring harness for improper connections, pinches and cut
Vacuum hoses for splits, kinks and improper connections
Hoses and ducts for leaks
Air cleaner clogging
Gasket
Confirm that electrical or mechanical loads are not applied.
Headlamp switch is OFF.
Air conditioner switch is OFF.
Rear window defogger switch is OFF.
SEF983U
Steering wheel is in the straight-ahead position, etc.
Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
I
SEF976U
5.
Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Make sure that no DTC is displayed with CONSULT or GST.
Is any DTC detected?
YES >> GO TO 2.
NO
>> GO TO 3.
M
SEF977U
2.REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
3.CHECK TARGET IDLE SPEED
1.
Run engine at about 2,000 rpm for about 2 minutes under no load.
P
Revision: August 2014
EC-135
2015 Rogue NAM
BASIC INSPECTION
[QR25DE]
< BASIC INSPECTION >
2. Rev engine (2,000 to 3,000 rpm) two or three times under no
load, then run engine at idle speed for about 1 minute.
3. Check idle speed.
For procedure, refer to EC-496, "Inspection".
For specification, refer to EC-503, "Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> GO TO 4.
PBIA8513J
4.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
2.
Stop engine.
Perform EC-142, "Work Procedure".
>> GO TO 5.
5.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform EC-143, "Work Procedure".
>> GO TO 6.
6.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-144, "Work Procedure".
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 7.
NO
>> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.CHECK TARGET IDLE SPEED AGAIN
1.
2.
Start engine and warm it up to normal operating temperature.
Check idle speed.
For procedure, refer to EC-496, "Inspection".
For specification, refer to EC-503, "Idle Speed".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
Check camshaft position sensor (PHASE) and circuit. Refer to EC-301, "DTC Description".
Check crankshaft position sensor (POS) and circuit. Refer to EC-298, "DTC Description".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace. Then GO TO 4
9.CHECK ECM FUNCTION
1.
2.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-66, "ECM : Work Procedure" (With intelligent key system) or SEC-159, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement" (Without intelligent key system).
>> GO TO 4.
10.CHECK IGNITION TIMING
1.
Run engine at idle.
Revision: August 2014
EC-136
2015 Rogue NAM
BASIC INSPECTION
< BASIC INSPECTION >
2. Check ignition timing with a timing light.
For procedure, refer to EC-497, "Inspection"
For specification, refer to EC-503, "Ignition Timing".
[QR25DE]
A
Timing indicator
EC
Is the inspection result normal?
YES >> INSPECTION END.
NO
>> GO TO 11.
11.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
2.
JPBIA5854ZZ
Stop engine.
Perform EC-142, "Work Procedure".
>> GO TO 12.
12.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform EC-143, "Work Procedure".
G
>> GO TO 13.
13.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-144, "Work Procedure".
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 14.
NO
>> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
1.
2.
14.CHECK TARGET IDLE SPEED AGAIN
Start engine and warm it up to normal operating temperature.
Check idle speed.
For procedure, refer to EC-496, "Inspection".
For specification, refer to EC-503, "Idle Speed".
Is the inspection result normal?
YES >> GO TO 15.
NO
>> GO TO 17.
15.CHECK IGNITION TIMING AGAIN
1.
2.
Run engine at idle.
Check ignition timing with a timing light.
For procedure, refer to EC-497, "Inspection".
For specification, refer to EC-503, "Ignition Timing".
Timing indicator
Is the inspection result normal?
YES >> INSPECTION END.
NO
>> GO TO 16.
JPBIA5854ZZ
16.CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to EM-50, "Removal and Installation".
Is the inspection result normal?
YES >> GO TO 17.
NO
>> Repair the timing chain installation. Then GO TO 4.
Revision: August 2014
EC-137
2015 Rogue NAM
BASIC INSPECTION
[QR25DE]
< BASIC INSPECTION >
17.DETECT MALFUNCTIONING PART
Check the following.
Check camshaft position sensor (PHASE) and circuit. Refer to EC-301, "DTC Description".
Check crankshaft position sensor (POS) and circuit. Refer to EC-298, "DTC Description".
Is the inspection result normal?
YES >> GO TO 18.
NO
>> Repair or replace. Then GO TO 4
18.CHECK ECM FUNCTION
1.
2.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-66, "ECM : Work Procedure" (With intelligent key system) or SEC-159, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement" (Without intelligent key system).
>> GO TO 4.
Revision: August 2014
EC-138
2015 Rogue NAM
ADDITIONAL SERVICE WHEN REPLACING ECM
[QR25DE]
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING ECM
Description
INFOID:0000000011277895
When replacing ECM, the following procedure must be performed. (For details, refer to EC-139, "Work Proce- EC
dure".)
PROGRAMMING OPERATION
NOTE:
After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the procedure to perform the programming.
Work Procedure
INFOID:0000000011277896
1.SAVE ECM DATA
With CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Turn ignition switch ON.
4. Select SAVING DATA FOR REPLC CPU in WORK SUPPORT mode of ENGINE using CONSULT.
5. Follow the instruction of CONSULT display.
NOTE:
Necessary data in ECM is copied and saved to CONSULT.
Go to Step 2 regardless of with or without success in saving data.
>> GO TO 2.
2.CHECK ECM PART NUMBER
Check ECM part number to see whether it is blank ECM or not.
NOTE:
Part number of blank ECM is 23703 - .
Check part number when ordering ECM or the one included in the label on the container box.
Is the ECM a blank ECM?
YES >> GO TO 3.
NO
>> GO TO 5.
3.SAVE ECM PART NUMBER
Read out the part number from the old ECM and save the number, following the programming instructions.
Refer to CONSULT Operation Manual.
NOTE:
The ECM part number is saved in CONSULT.
Even when ECM part number is not saved in CONSULT, go to 4.
>> GO TO 4.
4.PERFORM ECM PROGRAMMING
After replacing ECM, perform the ECM programming. Refer to CONSULT Operation Manual.
NOTE:
Refer to EC-502, "Removal and Installation" for replacement of ECM.
During programming, maintain the following conditions:
- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 13.5 V (Be sure to check the value of battery voltage by selecting BATTERY VOLT in
Data monitor of CONSULT.)
>> GO TO 6.
5.REPLACE ECM
Revision: August 2014
EC-139
2015 Rogue NAM
ADDITIONAL SERVICE WHEN REPLACING ECM
[QR25DE]
< BASIC INSPECTION >
Replace ECM. Refer to EC-502, "Removal and Installation".
>> GO TO 6.
6.PERFORM INITIALIZATION OF IVIS (NATS) SYSTEM AND REGISTRATION OF ALL IVIS (NATS) IGNITION KEY IDS
Refer to SEC-63, "Work Flow" (with intelligent key system) or SEC-156, "Work Flow" (without intelligent key
system).
>> GO TO 7.
7.CHECK ECM DATA STATUS
Check if the data is successfully copied from the ECM at Step 1 (before replacement) and saved in CONSULT.
Is the data saved successfully?
YES >> GO TO 8.
NO
>> GO TO 9.
8.WRITE ECM DATA
With CONSULT
1. Select WRITING DATA FOR REPLC CPU in WORK SUPPORT mode of ENGINE using CONSULT.
2. Follow the instruction of CONSULT display.
NOTE:
The data saved by SAVING DATA FOR REPLC CPU is written to ECM.
>> GO TO 10.
9.PERFORM VIN REGISTRATION
Refer to EC-141, "Work Procedure".
>> GO TO 10.
10.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
Perform Accelerator Pedal Released Position Learning. Refer to EC-142, "Work Procedure".
>> GO TO 11.
11.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
>> GO TO 12.
12.PERFORM IDLE AIR VOLUME LEARNING
Perform Idle Air Volume Learning. Refer to EC-144, "Work Procedure".
>> END
Revision: August 2014
EC-140
2015 Rogue NAM
VIN REGISTRATION
[QR25DE]
< BASIC INSPECTION >
VIN REGISTRATION
Description
INFOID:0000000011277897
VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M).
Work Procedure
INFOID:0000000011277898
EC
1.CHECK VIN
D
Check the VIN of the vehicle and note it. Refer to GI-34, "Identification Number".
>> GO TO 2.
2.PERFORM VIN REGISTRATION
1.
2.
3.
With CONSULT
Turn ignition switch ON and engine stopped.
Select VIN REGISTRATION in WORK SUPPORT mode of ENGINE using CONSULT.
Follow the instruction of CONSULT display.
>> END
Revision: August 2014
EC-141
2015 Rogue NAM
ACCELERATOR PEDAL RELEASED POSITION LEARNING
[QR25DE]
< BASIC INSPECTION >
ACCELERATOR PEDAL RELEASED POSITION LEARNING
Description
INFOID:0000000011277899
Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the
accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each
time harness connector of accelerator pedal position sensor or ECM is disconnected.
Work Procedure
INFOID:0000000011277900
1.START
1.
2.
3.
4.
5.
Make sure that accelerator pedal is fully released.
Turn ignition switch ON and wait at least 2 seconds.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON and wait at least 2 seconds.
Turn ignition switch OFF and wait at least 10 seconds.
>> END
Revision: August 2014
EC-142
2015 Rogue NAM
THROTTLE VALVE CLOSED POSITION LEARNING
[QR25DE]
< BASIC INSPECTION >
THROTTLE VALVE CLOSED POSITION LEARNING
Description
A
INFOID:0000000011277901
Throttle Valve Closed Position Learning is a function of ECM to learn the fully closed position of the throttle EC
valve by monitoring the throttle position sensor output signal. It must be performed each time the harness connector of the electric throttle control actuator or ECM is disconnected or electric throttle control actuator inside
is cleaned.
C
Work Procedure
INFOID:0000000011277902
1.START
With CONSULT
Turn ignition switch ON.
Select CLSD THL POS LEARN in WORK SUPPORT mode of ENGINE using CONSULT.
Follow the instructions on the CONSULT display.
Turn ignition switch OFF and wait at least 10 seconds.
Check that throttle valve moves during the above 10 seconds by confirming the operating sound.
Without CONSULT
1. Start the engine.
NOTE:
Engine coolant temperature is 25C (77F) or less before engine starts.
2. Warm up the engine.
NOTE:
Raise engine coolant temperature until it reaches 65C (149F) or more.
3. Turn ignition switch OFF and wait at least 10 seconds.
Check that throttle valve moves during the above 10 seconds by confirming the operating sound.
1.
2.
3.
4.
>> END
Revision: August 2014
EC-143
2015 Rogue NAM
IDLE AIR VOLUME LEARNING
[QR25DE]
< BASIC INSPECTION >
IDLE AIR VOLUME LEARNING
Description
INFOID:0000000011277903
Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps each engine idle speed
within the specific range. It must be performed under any of the following conditions:
Each time electric throttle control actuator or ECM is replaced.
Idle speed or ignition timing is out of specification.
Work Procedure
INFOID:0000000011277904
1.PRECONDITIONING
Make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
Battery voltage: More than 12.9 V (At idle)
Engine coolant temperature: 70 - 100C (158 - 212F)
Selector lever : P or N
Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime running light systems, set lighting switch to the 1st position to
light only small lamps.
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed-up
With CONSULT
Drive vehicle until ATF TENP SEN in DATA MONITOR mode of CVT system indicates less than 0.9 V.
Without CONSULT
Drive vehicle for 10 minutes.
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 3.
2.IDLE AIR VOLUME LEARNING
With CONSULT
1. Perform Accelerator Pedal Released Position Learning. Refer to EC-142, "Work Procedure".
2. Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
3. Start engine and warm it up to normal operating temperature.
4. Select IDLE AIR VOL LEARN in WORK SUPPORT mode of ENGINE.
5. Touch START and wait 20 seconds.
Is CMPLT displayed on CONSULT screen?
YES >> GO TO 4.
NO
>> GO TO 5.
3.IDLE AIR VOLUME LEARNING
Without CONSULT
NOTE:
It is better to count the time accurately with a clock.
It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1. Perform Accelerator Pedal Released Position Learning. Refer to EC-142, "Work Procedure".
2. Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
6. Repeat the following procedure quickly five times within 5 seconds.
Fully depress the accelerator pedal.
Fully release the accelerator pedal.
7. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops
blinking and turned ON.
Revision: August 2014
EC-144
2015 Rogue NAM
IDLE AIR VOLUME LEARNING
[QR25DE]
< BASIC INSPECTION >
8. Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
9. Start engine and let it idle.
10. Wait 20 seconds.
EC
D
SEC897C
>> GO TO 4
4.CHECK IDLE SPEED AND IGNITION TIMING
Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications. For specification, refer to EC-503, "Idle Speed" and EC-503, "Ignition Timing".
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following
Check that throttle valve is fully closed.
Check PCV valve operation.
Check that downstream of throttle valve is free from air leakage.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace malfunctioning part.
6.DETECT MALFUNCTIONING PART
Engine component parts and their installation condition are questionable. Check and eliminate the cause of
the incident.
It is useful to perform TROUBLE DIAGNOSIS - SPECIFICATION VALUE. Refer to EC-160, "Description".
If any of the following conditions occur after the engine has started, eliminate the cause of the incident and
perform Idle Air Volume Learning all over again:
Engine stalls.
Erroneous idle.
>> INSPECTION END
Revision: August 2014
EC-145
2015 Rogue NAM
MIXTURE RATIO SELF-LEARNING VALUE CLEAR
[QR25DE]
< BASIC INSPECTION >
MIXTURE RATIO SELF-LEARNING VALUE CLEAR
Description
INFOID:0000000011277905
This describes how to erase the mixture ratio self-learning value. For the actual procedure, follow the instructions in Diagnosis Procedure.
Work Procedure
INFOID:0000000011277906
1.START
With CONSULT
Start engine and warm it up to normal operating temperature.
Select SELF-LEARNING CONT in WORK SUPPORT mode of ENGINE using CONSULT.
Clear mixture ratio self-learning value by touching CLEAR.
With GST
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF.
3. Disconnect mass air flow sensor harness connector.
4. Restart engine and let it idle for at least 5 seconds.
5. Stop engine and reconnect mass air flow sensor harness connector.
6. Select Service $03 with GST. Make sure DTC P0102 is detected.
7. Select Service $04 with GST to erase the DTC P0102.
1.
2.
3.
>> END
Revision: August 2014
EC-146
2015 Rogue NAM
FUEL PRESSURE
[QR25DE]
< BASIC INSPECTION >
FUEL PRESSURE
Work Procedure
INFOID:0000000011277907
FUEL PRESSURE RELEASE
EC
1.FUEL PRESSURE RELEASE
With CONSULT
Turn ignition switch ON.
Perform FUEL PRESSURE RELEASE in WORK SUPPORT mode of ENGINE using CONSULT.
Start engine.
After engine stalls, crank it two or three times to release all fuel pressure.
Turn ignition switch OFF.
Without CONSULT
1. Remove fuel pump fuse located in IPDM E/R. For the fuse number, refer to EC-108, "Wiring Diagram". For
the fuse arrangement, refer to PG-68, "IPDM E/R Terminal Arrangement".
2. Start engine.
3. After engine stalls, crank it two or three times to release all fuel pressure.
4. Turn ignition switch OFF.
5. Reinstall fuel pump fuse after servicing fuel system.
1.
2.
3.
4.
5.
>> END
FUEL PRESSURE CHECK
CAUTION:
Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger.
NOTE:
Prepare pans or saucers under the disconnected fuel line because the fuel may spill out. The fuel
pressure cannot be completely released because this models do not have fuel return system.
Use Fuel Pressure Gauge Kit [SST: (J-44321)] to check fuel pressure.
1.FUEL PRESSURE CHECK
1.
2.
: Fuel pressure gauge
: Fuel feed hose
: Vehicle front
3.
4.
5.
Turn ignition switch ON and check for fuel leakage.
Start engine and check for fuel leakage.
Read the indication of fuel pressure gauge.
M
ALBIA0811ZZ
At idling : Approximately 350 kPa (3.57 kg/cm2, 51 psi)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK FUEL HOSES AND FUEL TUBES
Check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly. Refer to FL-5, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Revision: August 2014
Release fuel pressure to zero.
Connect fuel tube adapter [SST:KV10120000] (B) to quick connector.
A
EC-147
2015 Rogue NAM
HOW TO SET SRT CODE
[QR25DE]
< BASIC INSPECTION >
HOW TO SET SRT CODE
Description
INFOID:0000000011277908
OUTLINE
In order to set all SRTs, the self-diagnoses as in the SRT ITEM table must have been performed at least
once. Each diagnosis may require actual driving for a long period of time under various conditions.
SRT ITEM
The table below shows required self-diagnostic items to set the SRT to CMPLT.
SRT item*1
(CONSULT indication)
Performance
Priority*2
Required self-diagnostic items to set the SRT to CMPLT
Corresponding
DTC No.
CATALYST
Three way catalyst function
P0420
EVAP SYSTEM
EVAP control system purge flow monitoring
P0441
EVAP control system
P0456
Air fuel ratio (A/F) sensor 1
P014C, P014D,
P015A, P015B
Heated oxygen sensor 2
P0137
Heated oxygen sensor 2
P0138
Heated oxygen sensor 2
P0139
Intake value timing control function
P0011, P052A,
P052B
HO2S
EGR/VVT SYSTEM
*1: Though displayed on the CONSULT screen, HO2S HTR is not SRT item.
*2: If completion of several SRTs is required, perform driving patterns (DTC confirmation procedure), one by
one based on the priority for models with CONSULT.
SRT SERVICE PROCEDURE
Revision: August 2014
EC-148
2015 Rogue NAM
HOW TO SET SRT CODE
[QR25DE]
< BASIC INSPECTION >
If a vehicle has failed the state emissions inspection due to one or more SRT items indicating INCMP, review
the flowchart diagnostic sequence, referring to the following flowchart.
EC
K
JSBIA0400GB
SRT Set Driving Pattern
INFOID:0000000011277909
CAUTION:
M
Revision: August 2014
EC-149
2015 Rogue NAM
HOW TO SET SRT CODE
[QR25DE]
< BASIC INSPECTION >
Always drive the vehicle in safe manner according to traffic conditions and obey all traffic laws.
JPBIA5560GB
*1: Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal
and keep it released for more than 10 seconds. Depress the accelerator pedal until vehicle speed is 90 km/h
(56 MPH) again.
*2: Checking the vehicle speed with GST is advised.
The time required for each diagnosis varies with road surface conditions, weather, altitude, individual driving
habits, etc.
Zone A is the fastest time where required for the diagnosis under normal conditions*. If the diagnosis is not
completed within Zone A, the diagnosis can still be performed within Zone B.
Revision: August 2014
EC-150
2015 Rogue NAM
HOW TO SET SRT CODE
[QR25DE]
< BASIC INSPECTION >
*: Normal conditions
- Sea level
A
- Flat road
- Ambient air temperature: 20 30C (68 86F)
NOTE:
Diagnosis is performed as quickly as possible under normal conditions. However, under other conditions, EC
diagnosis may also be performed. [For example: ambient air temperature other than 20 30C (68 86F)]
Work Procedure
INFOID:0000000011277910
1.CHECK DTC
Check DTC.
Is any DTC detected?
YES >> Repair malfunction(s) and erase DTC. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK SRT STATUS
With CONSULT
Select SRT STATUS in DTC & SRT CONFIRMATION mode with CONSULT.
Without CONSULT
Perform SRT status mode with EC-66, "On Board Diagnosis Function".
With GST
Select Service $01 with GST.
Is SRT code(s) set?
YES >> GO TO 11.
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 4.
3.DTC CONFIRMATION PROCEDURE
1.
2.
Select SRT WORK SUPPORT in DTC & SRT CONFIRMATION mode with CONSULT.
For SRT(s) that is not set, perform the corresponding DTC CONFIRMATION PROCEDURE according to
the Performance Priority in the SRT ITEM table. Refer to EC-148, "Description".
3. Check DTC.
Is any DTC detected?
YES >> Repair malfunction(s) and erase DTC. Refer to EC-96, "DTC Index".
NO
>> GO TO 10.
4.PERFORM ROAD TEST
Check the Performance Priority in the SRT ITEM table. Refer to EC-148, "Description".
Perform the most efficient SRT set driving pattern to set the SRT properly. Refer to EC-149, "SRT Set Driving Pattern".
In order to set all SRTs, the SRT set driving pattern must be performed at least once.
>> GO TO 5.
5.PATTERN 1
1. Check the vehicle condition;
Engine coolant temperature is 10 to 35C (14 to 95F).
Fuel tank temperature is more than 0C (32F).
2. Start the engine.
3. Keep engine idling until the engine coolant temperature is greater than 70C (158F)
NOTE:
ECM terminal voltage is follows;
Engine coolant temperature
- 10 to 35C (14 to 95F): 3.0 4.3 V
- 70(158F): Less than 4.1 V
Fuel tank temperature: Less than 1.4 V
Refer toEC-80, "Reference Value".
Revision: August 2014
EC-151
2015 Rogue NAM
HOW TO SET SRT CODE
[QR25DE]
< BASIC INSPECTION >
>> GO TO 6.
6.PATTERN 2
1.
Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then
release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
Checking the vehicle speed with GST is advised.
When steady-state driving is performed again even after it is interrupted, each diagnosis can be conducted.
In this case, the time required for diagnosis may be extended.
>> GO TO 7.
7.PATTERN 3
Operate vehicle following the driving pattern shown in the figure.
- Release the accelerator pedal during deceleration of vehicle speed
from 90 km/h (56 MPH) to 0 km/h (0 MPH).
>> GO TO 8.
PBIB2244E
8.PATTERN 4
Operate vehicle following the driving pattern shown in the figure.
- Drive the vehicle in a proper gear at 60 km/h (38 MPH) and maintain the speed.
- Release the accelerator pedal fully at least 5 seconds.
- Repeat the above two steps at least 5 times.
>> GO TO 9.
JSBIA0160GB
9.PATTERN 5
The accelerator pedal must be held very steady during steady-state driving.
If the accelerator pedal is moved, the test must be conducted again.
>> GO TO 10.
10.CHECK SRT STATUS
With CONSULT
Select SRT STATUS in DTC & SRT CONFIRMATION mode with CONSULT.
Without CONSULT
Perform SRT status mode with EC-66, "On Board Diagnosis Function".
With GST
Select Service $01 with GST.
Is SRT(s) set?
YES >> GO TO 11.
NO
>> Call TECH LINE or take appropriate action.
11.CHECK PERMANENT DTC
Revision: August 2014
EC-152
2015 Rogue NAM
HOW TO SET SRT CODE
< BASIC INSPECTION >
NOTE:
Permanent DTC cannot be checked with a tool other than CONSULT or GST.
With CONSULT
Select SRT STATUS in DTC & SRT CONFIRMATION mode with CONSULT.
With GST
Select Service $0A with GST.
Is permanent DTC(s) detected?
YES >> Proceed to EC-154, "Description".
NO
>> END
[QR25DE]
A
EC
Revision: August 2014
EC-153
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
HOW TO ERASE PERMANENT DTC
Description
INFOID:0000000011277911
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL shutoff if the same malfunction is not detected after performing the driving pattern for MIL shutoff three times in a raw.
JSBIA0063GB
*1:
When the same malfunction is detected in two consecutive trips, MIL
will illuminate.
*2:
MIL will turn off after vehicle is driven
3 times (driving pattern B) without
any malfunctions.
When a DTC is not stored in ECM
The erasing method depends on a permanent DTC stored in ECM. Refer to the following table.
NOTE:
If the applicable permanent DTC includes multiple groups, perform the procedure of Group B first. If the permanent DTC is not erased, perform the procedure of Group A.
: Applicable : Not applicable
Driving pattern
Group*
Perform DTC CONFIRMATION PROCEDURE for applicable DTCs.
EC-155
EC-157
Reference
*: For group, refer to EC-96, "DTC Index".
PERMANENT DTC ITEM
For permanent DTC items, MIL turns ON. Refer to EC-96, "DTC Index".
Revision: August 2014
EC-154
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
PERMANENT DTC SERVICE PROCEDURE
EC
H
JSBIA0401GB
Work Procedure (Group A)
INFOID:0000000011277912
JSBIA0064GB
Revision: August 2014
EC-155
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
*1:
When the same malfunction is detected in two consecutive trips, MIL
will illuminate.
1.CHECK DTC
Check DTC.
Is any DTC detected?
YES >> Repair malfunction(s) and erase DTC.
NO
>> GO TO 2.
2.CHECK PERMANENT DTC
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES >> GO TO 3.
NO
>> END
1.
2.
3.
4.
5.
3.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for DTCs which are the same as permanent DTCs stored in
ECM. Refer to EC-96, "DTC Index".
>> GO TO 4.
4.CHECK PERMANENT DTC
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES >> GO TO 1.
NO
>> END
1.
2.
3.
4.
5.
Revision: August 2014
EC-156
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
Work Procedure (Group B)
INFOID:0000000011277913
EC
JSBIA0414GB
*1:
When the same malfunction is detected in two consecutive trips, MIL
will illuminate.
*2:
After experiencing driving pattern B
and D, permanent DTC is erased.
*3:
Indication does not change unless
the ignition switch is turned from ON
to OFF twice even after experiencing
driving pattern B or D.
NOTE:
Drive the vehicle according to only driving patterns indicating INCMP in driving patterns B and D on the
PERMANENT DTC STATUS screen.
1.CHECK DTC
Check DTC.
Is any DTC detected?
YES >> Repair malfunction(s) and erase DTC.
NO
>> GO TO 2.
2.CHECK PERMANENT DTC
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
1.
2.
3.
4.
5.
Revision: August 2014
EC-157
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES >> GO TO 3.
NO
>> END
3.DRIVE DRIVING PATTERN B
CAUTION:
Always drive at a safe speed.
Never erase self-diagnosis results.
If self-diagnosis results are erased during the trip of driving pattern B or D, the counter of driving
pattern B and D is reset.
With CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Use PERMANENT DTC WORK SUPPORT mode with CONSULT to drive the vehicle according to driving pattern B. Refer to EC-69, "CONSULT Function", EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
With GST
1. Start engine and warm it up to normal operating temperature.
2. Drive the vehicle according to driving pattern B. Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving
Pattern".
>> GO TO 4.
4.CHECK PERMANENT DTC
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS mode with CONSULT.
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES >> GO TO 5.
NO
>> END
1.
2.
3.
4.
5.
5.DRIVE DRIVING PATTERN D
CAUTION:
Always drive at a safe speed.
Never erase self-diagnosis results.
If self-diagnosis results are erased during the trip of driving pattern B or D, the counter of driving
pattern B and D is reset.
Drive the vehicle according to driving pattern D. Refer to EC-63, "DIAGNOSIS DESCRIPTION : Driving Pattern".
>> GO TO 6.
6.CHECK PERMANENT DTC
1.
2.
3.
4.
5.
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select PERMANENT DTC STATUS mode with CONSULT.
Revision: August 2014
EC-158
2015 Rogue NAM
HOW TO ERASE PERMANENT DTC
[QR25DE]
< BASIC INSPECTION >
With GST
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select Service $0A with GST.
Is any permanent DTC detected?
YES >> GO TO 1.
NO
>> END
EC
Revision: August 2014
EC-159
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Description
INFOID:0000000011277914
The specification (SP) value indicates the tolerance of the value that is displayed in SPEC of DATA MONITOR mode of CONSULT during normal operation of the Engine Control System. When the value in SPEC of
DATA MONITOR mode is within the SP value, the Engine Control System is confirmed OK. When the value
in SPEC of DATA MONITOR mode is NOT within the SP value, the Engine Control System may have one
or more malfunctions.
The SP value is used to detect malfunctions that may affect the Engine Control System, but will not light the
MIL.
The SP value will be displayed for the following three items:
B/FUEL SCHDL (The fuel injection pulse width programmed into ECM prior to any learned on board correction)
A/F ALPHA-B1 (The mean value of air-fuel ratio feedback correction factor per cycle)
MASS AIR FLOW SENSOR (Hz) (The signal frequency of the mass air flow sensor)
Component Function Check
INFOID:0000000011277915
1.START
Make sure that all of the following conditions are satisfied.
Vehicle driven distance: More than 5,000 km (3,107 miles)
Barometric pressure: 98.3 - 104.3 kPa (1.003 - 1.064 kg/cm2, 14.25 - 15.12 psi)
Atmospheric temperature: 20 - 30C (68 - 86F)
Engine coolant temperature: 75 - 95C (167 - 203F)
Transmission: Warmed-up
- After the engine is warmed up to normal operating temperature, drive vehicle until ATF TEMP SEN (CVT
fluid temperature sensor signal) indicates more than 60C (140F).
Electrical load: Not applied*
Engine speed: Idle
*: Rear window defogger switch, air conditioner switch, lighting switch are OFF. Steering wheel is straight
ahead.
>> GO TO 2.
2.PERFORM SPEC OF DATA MONITOR MODE
With CONSULT
NOTE:
Perform SPEC in DATA MONITOR mode in maximum scale display.
1. Perform EC-135, "Work Procedure".
2. Select B/FUEL SCHDL, A/F ALPHA-B1 and MASS AIR FLOW SENSOR (Hz) in SPEC of DATA
MONITOR mode with CONSULT.
3. Make sure that monitor items are within the SP value.
Is the inspection result normal?
YES >> END
NO
>> Proceed to EC-161, "Diagnosis Procedure".
Revision: August 2014
EC-160
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011277916
OVERALL SEQUENCE
EC
P
PBIB2318E
Revision: August 2014
EC-161
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
PBIB3213E
DETAILED PROCEDURE
1.CHECK A/F ALPHA-B1
1.
2.
3.
With CONSULT
Start engine.
Confirm that the testing conditions are met. Refer to EC-160, "Component Function Check".
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the each indication is
within the SP value.
Revision: August 2014
EC-162
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NOTE:
Check A/F ALPHA-B1 for approximately 1 minute because they may fluctuate. It is NG if the indication is A
out of the SP value even a little.
Is the measurement value within the SP value?
YES >> GO TO 17.
EC
NO-1 >> Less than the SP value: GO TO 2.
NO-2 >> More than the SP value: GO TO 3.
2.CHECK B/FUEL SCHDL
Select B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the indication is within the
SP value.
Is the measurement value within the SP value?
YES >> GO TO 4.
NO
>> More than the SP value: GO TO 19.
3.CHECK B/FUEL SCHDL
Select B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the indication is within the
SP value.
Is the measurement value within the SP value?
YES >> GO TO 6.
NO-1 >> More than the SP value: GO TO 6.
NO-2 >> Less than the SP value: GO TO 25.
4.CHECK A/F ALPHA-B1
Stop the engine.
Disconnect PCV hose, and then plug it.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the indication is within
the SP value.
Is the measurement value within the SP value?
YES >> GO TO 5.
NO
>> GO TO 6.
1.
2.
1.
2.
3.
4.
5.CHANGE ENGINE OIL
Stop the engine.
Change engine oil.
NOTE:
This symptom may occur when a large amount of gasoline is mixed with engine oil because of driving
conditions (such as when engine oil temperature does not rise enough since a journey distance is too
short during winter). The symptom will not be detected after changing engine oil or changing driving condition.
>> INSPECTION END
6.CHECK FUEL PRESSURE
Check fuel pressure. (Refer to EC-147, "Work Procedure".)
Is the inspection result normal?
YES >> GO TO 9.
NO-1 >> Fuel pressure is too high: Replace fuel filter and fuel pump assembly, refer to FL-5, "Removal
and Installation", and then GO TO 8.
NO-2 >> Fuel pressure is too low: GO TO 7.
7.DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly, refer to FL-5, "Removal and Installation", and then
GO TO 8.
NO
>> Repair or replace and then GO TO 8.
Revision: August 2014
EC-163
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
8.CHECK A/F ALPHA-B1
1.
2.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the indication is within
the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> GO TO 9.
9.PERFORM POWER BALANCE TEST
1. Perform POWER BALANCE in ACTIVE TEST mode.
2. Make sure that the each cylinder produces a momentary engine speed drop.
Is the inspection result normal?
YES >> GO TO 12.
NO
>> GO TO 10.
10.DETECT MALFUNCTIONING PART
Check the following.
1. Ignition coil and its circuit (Refer to EC-473, "Component Function Check".)
2. Fuel injector and its circuit (Refer to EC-467, "Component Function Check".)
3. Intake air leakage
4. Low compression pressure (Refer to EM-24, "Compression pressure".)
Is the inspection result normal?
YES >> Replace fuel injector, refer to EM-45, "Removal and Installation", and then GO TO 11.
NO
>> Repair or replace malfunctioning part and then GO TO 11.
11.CHECK A/F ALPHA-B1
1.
2.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the indication is within
the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> GO TO 12.
12.CHECK A/F SENSOR 1 FUNCTION
Perform all DTC CONFIRMATION PROCEDURE related with A/F sensor 1.
For DTC P0130, refer to EC-229, "DTC Description".
For DTC P0131, refer to EC-233, "DTC Description".
For DTC P0132, refer to EC-236, "DTC Description".
For DTC P014C, P014D, P15A, P15B refer to EC-258, "DTC Description".
For DTC P2096, P2097, refer to EC-429, "DTC Description".
Is any DTC detected?
YES >> GO TO 15.
NO
>> GO TO 13.
13.CHECK A/F SENSOR 1 CIRCUIT
Perform DIAGNOSTIC PROCEDURE according to corresponding DTC.
>> GO TO 14.
14.CHECK A/F ALPHA-B1
1.
2.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the each indication is
within the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> GO TO 15.
Revision: August 2014
EC-164
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
15.DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR
1.
2.
Stop the engine.
Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.
EC
>> GO TO 16.
16.CHECK A/F ALPHA-B1
1.
2.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the indication is within
the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> Detect malfunctioning part according to EC-489, "Symptom Table".
17.CHECK B/FUEL SCHDL
Select B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the indication is within the
SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO-1 >> More than the SP value: GO TO 18.
NO-2 >> Less than the SP value: GO TO 25.
18.DETECT MALFUNCTIONING PART
1.
2.
-
Check for the cause of large engine friction. Refer to the following.
Engine oil level is too high
Engine oil viscosity
Belt tension of power steering, alternator, A/C compressor, etc. is excessive
Noise from engine
Noise from transmission, etc.
Check for the cause of insufficient combustion. Refer to the following.
Valve clearance malfunction
Intake valve timing control function malfunction
Camshaft sprocket installation malfunction, etc.
>> Repair or replace malfunctioning part, and then GO TO 30.
19.CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
Crushed air ducts
Malfunctioning seal of air cleaner element
Uneven dirt of air cleaner element
Improper specification of intake air system
Is the inspection result normal?
YES >> GO TO 21.
NO
>> Repair or replace malfunctioning part, and then GO TO 20.
20.CHECK A/F ALPHA-B1, AND B/FUEL SCHDL
Select A/F ALPHA-B1 and B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the
each indication is within the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> B/FUEL SCHDL is more, A/F ALPHA-B1 is less than the SP value: GO TO 21.
21.DISCONNECT AND RECONNECT MASS AIR FLOW SENSOR HARNESS CONNECTOR
1.
2.
Stop the engine.
Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and
then reconnect it again.
Revision: August 2014
EC-165
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> GO TO 22.
22.CHECK A/F ALPHA-B1
1.
2.
Start engine.
Select A/F ALPHA-B1 in SPEC of DATA MONITOR mode, and make sure that the indication is within
the SP value.
Is the measurement value within the SP value?
YES >> Detect malfunctioning part of mass air flow sensor circuit and repair it. Refer to EC-201, "DTC
Description". Then GO TO 29.
NO
>> GO TO 23.
23.CHECK MASS AIR FLOW SENSOR (HZ)
Select MASS AIR FLOW SENSOR (Hz) in SPEC of DATA MONITOR mode, and make sure that the indication is within the SP value.
Is the measurement value within the SP value?
YES >> GO TO 24.
NO
>> More than the SP value: Replace mass air flow sensor, refer to EM-26, "Removal and Installation", and then GO TO 29.
24.REPLACE ECM
Replace ECM. Refer to EC-502, "Removal and Installation".
>> GO TO 29.
25.CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
Crushed air ducts
Malfunctioning seal of air cleaner element
Uneven dirt of air cleaner element
Improper specification of intake air system
Is the inspection result normal?
YES >> GO TO 27.
NO
>> Repair or replace malfunctioning part, and then GO TO 26.
26.CHECK B/FUEL SCHDL
Select B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the indication is within the
SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> Less than the SP value: GO TO 27.
27.CHECK MASS AIR FLOW SENSOR (HZ)
Select MASS AIR FLOW SENSOR (Hz) in SPEC of DATA MONITOR mode, and make sure that the indication is within the SP value.
Is the measurement value within the SP value?
YES >> GO TO 28.
NO
>> Less than the SP value: Replace mass air flow sensor, refer to EM-26, "Removal and Installation",
and then GO TO 30.
28.CHECK INTAKE SYSTEM
Check for the cause of air leak after the mass air flow sensor. Refer to the following.
Disconnection, looseness, and cracks in air duct
Looseness of oil filler cap
Disconnection of oil level gauge
Open stuck, breakage, hose disconnection, or cracks of PCV valve
Disconnection or cracks of EVAP purge hose, open stuck of EVAP canister purge volume control solenoid
valve
Revision: August 2014
EC-166
2015 Rogue NAM
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Malfunctioning seal of rocker cover gasket
Disconnection, looseness, or cracks of hoses, such as vacuum hose, connecting to intake air system parts
Malfunctioning seal of intake air system, etc.
>> GO TO 30.
EC
29.CHECK A/F ALPHA-B1 AND B/FUEL SCHDL
Select A/F ALPHA-B1 and B/FUEL SCHDL in SPEC of DATA MONITOR mode, and make sure that the
indication is within the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> Detect malfunctioning part according to EC-489, "Symptom Table".
30.CHECK B/FUEL SCHDL
Select B/FUEL SCHDL in SPEC of DATA MONITOR mode, and then make sure that the indication is
within the SP value.
Is the measurement value within the SP value?
YES >> INSPECTION END
NO
>> Detect malfunctioning part according to EC-489, "Symptom Table".
Revision: August 2014
EC-167
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000011277917
1.CHECK FUSE
Check that the following fuse is not fusing.
Location
Fuse No.
Capacity
#48
5A
#41
10 A
#35
15 A
IPDM E/R
Is the fuse fusing?
YES >> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 2.
2.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E9 or E15. Refer to GI-46, "Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace ground connection.
3.CHECK ECM GROUND CIRCUIT
1.
2.
Disconnect ECM harness connectors.
Check the continuity between ECM harness connector and ground.
+
ECM
Connector
Terminal
F52
52
F51
16
123
E16
Continuity
Ground
Existed
128
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK ECM POWER SUPPLY (MAIN)-1
1.
2.
3.
Reconnect ECM harness connector.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals.
ECM
Connector
E16
Voltage
128
Battery voltage
Terminal
121
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 6.
5.CHECK ECM POWER SUPPLY (MAIN)--2
1.
Turn ignition switch OFF and wait at least 10 seconds.
Revision: August 2014
EC-168
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Check the voltage between ECM harness connector terminals as per the following.
A
ECM
+
Connector
Condition
Voltage
(Approx.)
128
After turning ignition switch
OFF, battery voltage will exist for a few seconds
Drop to 0 V
EC
Terminal
E16
121
Is the inspection result normal?
YES >> GO TO 9.
NO
>> GO TO 7.
6.CHECK ECM POWER SUPPLY (MAIN) CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connectors.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Terminal
Connector
Terminal
E16
121
F35
73
Continuity
Connector
Existed
5. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
7.CHECK ECM RELAY CONTROL SIGNAL
Check the voltage between ECM harness connector terminals as per the following.
ECM
+
Connector
Terminal
Connector
Condition
89
0V
Terminal
Ignition switch ON
F52
Voltage
(Approx.)
E16
128
Turn ignition switch OFF
and wait at least 10 seconds.
Battery voltage
Is the inspection result normal?
YES >> Check Intermittent Incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 8.
8.CHECK ECM RELAY CONTROL SIGNAL CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
5.
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F52
89
F42
93
Existed
Also check harness for short to ground and to power.
Revision: August 2014
EC-169
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-40, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
9.CHECK IGNITION SWITCH SIGNAL
1.
2.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals.
ECM
Connector
Condition
Voltage
(Approx.)
Terminal
E16
109
128
Ignition switch OFF
0V
Ignition switch ON
Battery voltage
Is the inspection result normal?
YES >> GO TO 11.
NO
>> GO TO 10.
10.CHECK IGNITION SWITCH SIGNAL CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
E16
109
E120
19
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
11.CHECK ECM POWER SUPPLY (BACK-UP)
Check the voltage between ECM harness connector terminals.
ECM
Voltage
Connector
Terminal
Connector
Terminal
F52
81
E16
128
Battery voltage
Is the inspection result normal?
YES >> Check Intermittent Incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 12.
12.CHECK ECM POWER SUPPLY (BACK-UP) CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
Revision: August 2014
EC-170
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F52
81
E121
44
EC
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-171
2015 Rogue NAM
U0101 CAN COMM CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
U0101 CAN COMM CIRCUIT
Description
INFOID:0000000011277918
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Description
INFOID:0000000011277919
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
U0101
LOST COMM (TCM)
(Lost communication with TCM)
DTC detecting condition
When ECM is not transmitting or receiving CAN communication signal of
OBD (emission-related diagnosis) with TCM for 2 seconds or more.
POSSIBLE CAUSE
CAN communication line between TCM and ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 3 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-172, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277920
Perform the trouble diagnosis for CAN communication system. Refer to LAN-17, "Trouble Diagnosis Flow
Chart".
Revision: August 2014
EC-172
2015 Rogue NAM
U1001 CAN COMM CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
U1001 CAN COMM CIRCUIT
Description
INFOID:0000000011277921
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul- EC
tiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring. C
Each control unit transmits/receives data but selectively reads required data only.
DTC Description
INFOID:0000000011277922
DTC DETECTION LOGIC
U1001
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
CAN COMM CIRCUIT
(CAN COMM CIRCUIT)
DTC detecting condition
When ECM is not transmitting or receiving CAN communication signal other than OBD (emission related diagnosis) for 2 seconds or more.
POSSIBLE CAUSE
Harness or connectors (CAN communication line is open or shorted)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
I
1. Turn ignition switch ON and wait at least 3 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-173, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277923
Perform the trouble diagnosis for CAN communication system. Refer to LAN-17, "Trouble Diagnosis Flow
Chart".
Revision: August 2014
EC-173
2015 Rogue NAM
U1040 ENG COMM CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
U1040 ENG COMM CIRCUIT
DTC Description
INFOID:0000000011277924
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC
DTC detecting condition
ENG COMM CIRCUIT
(Engine communication circuit)
U1040
ECM cannot transmit a communication signal to generator.
POSSIBLE CAUSE
Harness or connectors
(LIN communication circuit is open or shorted.)
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted. always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition ON and wait at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-174, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277925
1.CHECK LIN COMMUNICATION CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector and generator harness connector.
Check the continuity between ECM harness connector and generator harness connector.
+
ECM
Generator
Continuity
Connector
Terminal
Connector
Terminal
F52
85
F31
Existed
4. Also check harness for short to power and short to ground.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.REPLACE GENERATOR
1.
2.
3.
Replace generator. Refer to CHG-20, "Removal and Installation".
Erase DTC.
Perform DTC confirmation procedure again. Refer to EC-174, "DTC Description".
Revision: August 2014
EC-174
2015 Rogue NAM
U1040 ENG COMM CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
Is DTC detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
[QR25DE]
A
EC
Revision: August 2014
EC-175
2015 Rogue NAM
U1044 ENG COMM CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
U1044 ENG COMM CIRCUIT
DTC Description
INFOID:0000000011277926
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC
DTC detecting condition
ENG COMM CIRCUIT
(Engine communication circuit)
U1044
A signal voltage of LIN communication between ECM and generator is excessively
low or excessively high.
POSSIBLE CAUSE
Harness or connectors
(LIN communication circuit is open or shorted.)
Generator
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted. always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition ON and wait at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-176, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277927
1.CHECK LIN COMMUNICATION CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector and generator harness connector.
Check the continuity between ECM harness connector and generator harness connector.
+
ECM
Generator
Continuity
Connector
Terminal
Connector
Terminal
F52
85
F31
Existed
4. Also check harness for short to power and short to ground.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.REPLACE GENERATOR
1.
2.
3.
Replace generator. Refer to CHG-20, "Removal and Installation".
Erase DTC.
Perform DTC confirmation procedure again. Refer to EC-176, "DTC Description".
Revision: August 2014
EC-176
2015 Rogue NAM
U1044 ENG COMM CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
Is DTC detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
[QR25DE]
A
EC
Revision: August 2014
EC-177
2015 Rogue NAM
U1050, U1051 LIN COMMUNICATION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
U1050, U1051 LIN COMMUNICATION
DTC Description
INFOID:0000000011277928
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
U1050
DTC detecting condition
LIN COMMUNICATION
[LIN (Local Interconnect Network) communication)]
U1051
ECM detects LIN communication error.
POSSIBLE CAUSE
Harness or connectors
(LIN communication circuit is open or shorted.)
Generator
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted. always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition ON and wait at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-178, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277929
1.CHECK LIN COMMUNICATION CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector and generator harness connector.
Check the continuity between ECM harness connector and generator harness connector.
+
ECM
Generator
Continuity
Connector
Terminal
Connector
Terminal
F52
85
F31
Existed
4. Also check harness for short to power and short to ground.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.REPLACE GENERATOR
1.
Replace generator. Refer to CHG-20, "Removal and Installation".
Revision: August 2014
EC-178
2015 Rogue NAM
U1050, U1051 LIN COMMUNICATION
< DTC/CIRCUIT DIAGNOSIS >
2. Erase DTC.
3. Perform DTC confirmation procedure again. Refer to EC-178, "DTC Description".
Is DTC detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
[QR25DE]
A
EC
Revision: August 2014
EC-179
2015 Rogue NAM
P0011 IVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0011 IVT CONTROL
DTC Description
INFOID:0000000011277930
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
INT/V TIM CONT-B1
(A Camshaft position - timing over-advanced or system performance bank 1)
P0011
DTC detecting condition
There is a gap between angle of target and phase-control angle degree.
POSSIBLE CAUSE
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Intake valve control solenoid valve
Accumulation of debris to the signal pick-up portion of the camshaft
Timing chain installation
Foreign matter caught in the oil groove for intake valve timing control
FAIL-SAFE
Device fix mode
ECM activates the IVT intermediate lock control solenoid valve to bring the cam sprocket into an intermediate lock condition.
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-194, "DTC Description".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 11 V and 16 V at
idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
2.
3.
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Maintain the following conditions for at least 13 consecutive seconds. Hold the accelerator pedal as
steady as possible.
ENG SPEED
1,200 - 2,000 rpm
COOLAN TEMP/S
More than 60C (140F)
Selector lever
P or N position
4.
5.
Stop vehicle with engine running and let engine idle for 13 seconds.
Check 1st trip DTC.
With GST
Revision: August 2014
EC-180
2015 Rogue NAM
P0011 IVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-181, "Diagnosis Procedure".
NO
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE-2
1.
EC
With CONSULT
Maintain the following conditions for at least 20 consecutive seconds.
ENG SPEED
1,200 - 3,175 rpm (A constant rotation is maintained.)
COOLAN TEMP/S
More than 60C (140F)
Selector lever
D position
Driving location
Driving vehicle uphill
(Increased engine load will help maintain the driving
conditions required for this test.)
CAUTION:
Always drive at a safe speed.
2. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-181, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277931
1.CHECK DTC PRIORITY
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-194, "DTC Description".
NO
>> GO TO 2.
2.CHECK OIL PRESSURE WARNING LAMP
1.
2.
Start engine.
Check oil pressure warning lamp and confirm it is not illuminated.
Is oil pressure warning lamp illuminated?
YES >> Check the engine oil level. Refer to LU-7, "Inspection".
NO
>> GO TO 3.
N
PBIA8559J
3.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Check the intake valve timing control solenoid valve. Refer to EC-182, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Replace intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
4.CHECK CRANKSHAFT POSITION SENSOR (POS)
Check the crankshaft position sensor (POS). Refer to EC-300, "Component Inspection (Crankshaft Position
sensor)".
Is the inspection result normal?
Revision: August 2014
EC-181
2015 Rogue NAM
P0011 IVT CONTROL
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 5.
NO
>> Replace crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
[QR25DE]
5.CHECK CAMSHAFT POSITION SENSOR (PHASE)
Check the camshaft position sensor (PHASE). Refer to EC-303, "Component Inspection (Camshaft position
sensor)".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace camshaft position sensor (PHASE). Refer to EM-69, "Exploded View".
6.CHECK CAMSHAFT (INT)
Check the following.
Accumulation of debris to the signal plate of camshaft rear end
Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to EM-69, "Removal
and Installation".
JPBIA5855ZZ
7.CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned?
YES >> Check timing chain installation. Refer to EM-50, "Removal and Installation".
NO
>> GO TO 8.
8.CHECK LUBRICATION CIRCUIT
Refer to LU-7, "Inspection", INSPECTION AFTER INSTALLATION.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Clean lubrication line.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277932
1.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake valve timing control solenoid valve harness connector.
Check resistance between intake valve timing control solenoid valve terminals as per the following.
Intake valve timing control solenoid valve
+
Resistance
6.7 - 7.7 [at 20C (68F)]
Ground
(Continuity should not exist)
Terminal
1
1
2
Is the inspection result normal?
Revision: August 2014
EC-182
2015 Rogue NAM
P0011 IVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO
>> Replace intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-2
Remove intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between intake valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Make sure that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing control
solenoid valve is removed.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
1.
2.
EC
E
JMBIA2107ZZ
Revision: August 2014
EC-183
2015 Rogue NAM
P0014 EVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0014 EVT CONTROL
DTC Description
INFOID:0000000011277933
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
EXH/V TIM CONT-B1
(B Camshaft position - timing over-advanced or system performance bank 1)
P0014
DTC detecting condition
There is a gap between angle of target and phase-control angle degree.
POSSIBLE CAUSE
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Exhaust valve timing control position sensor
Exhaust valve control solenoid valve
Accumulation of debris to the signal pick-up portion of the camshaft
Timing chain installation
Foreign matter caught in the oil groove for exhaust valve timing control
FAIL-SAFE
Device fix mode
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0014 is displayed with DTC P0078 or P1078, first perform the trouble diagnosis for DTC P0078 or
P1078.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at
idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
2.
3.
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to the normal operating temperature.
Maintain the following conditions for at least 6 consecutive seconds. Hold the accelerator pedal as steady
as possible.
ENG SPEED
1,200 - 2,000 rpm (A constant rotation is maintained.)
COOLAN TEMP/S
More than 60C (140F)
Selector lever
P or N position
4.
5.
Let engine idle for 10 seconds.
Check 1st trip DTC.
With GST
Revision: August 2014
EC-184
2015 Rogue NAM
P0014 EVT CONTROL
< DTC/CIRCUIT DIAGNOSIS >
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-185, "Diagnosis Procedure"
NO
>> GO TO 4.
[QR25DE]
A
4.PERFORM DTC CONFIRMATION PROCEDURE-2
1.
2.
EC
With CONSULT
Select DATA MONITOR mode of ENGINE using CONSULT.
Maintain the following conditions for at least 20 consecutive seconds.
ENG SPEED
1,700 - 2,950 rpm (A constant rotation is maintained.)
COOLAN TEMP/S
More than 70C (158F)
Selector lever
D position
Driving location uphill
Driving vehicle uphill
(Increased engine load will help maintain the driving
conditions required for this test.)
CAUTION:
Always drive at a safe speed.
3. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-185, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
H
INFOID:0000000011277934
1.CHECK DTC PRIORITY
If DTC P0014 is displayed with DTC P0078 or P1078, first perform the trouble diagnosis for DTC P0078 or
P1078.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK OIL PRESSURE WARNING LAMP
1.
2.
Start engine.
Check oil pressure warning lamp and confirm it is not illuminated.
Is oil pressure warning lamp illuminated?
YES >> Check the engine oil level. Refer to LU-7, "Inspection".
NO
>> GO TO 3.
O
PBIA8559J
3.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE
Check the exhaust valve timing control solenoid valve. Refer to EC-182, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Replace exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
4.CHECK CRANKSHAFT POSITION SENSOR (POS)
Revision: August 2014
EC-185
2015 Rogue NAM
P0014 EVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Check the crankshaft position sensor (POS). Refer to EC-300, "Component Inspection (Crankshaft Position
sensor)".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
5.CHECK EXHAUST VALVE TIMING CONTROL POSITION SENSOR
Check the exhaust valve timing control position sensor. Refer to EC-390, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace exhaust valve timing control position sensor. Refer to EM-49, "Exploded View".
6.CHECK CAMSHAFT (EXH)
Check the following.
Accumulation of debris to the signal plate of camshaft rear end
Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to EM-69, "Removal
and Installation".
JPBIA5856ZZ
7.CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned?
YES >> Check timing chain installation. Refer to EM-50, "Removal and Installation".
NO
>> GO TO 8.
8.CHECK LUBRICATION CIRCUIT
Refer to LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Clean lubrication line.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277935
1.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect exhaust valve timing control solenoid valve harness connector.
Check resistance between exhaust valve timing control solenoid valve terminals as per the following.
Exhaust valve timing control solenoid valve
+
Resistance
7.0 - 7.7 [at 20C (68F)]
Terminal
1
Revision: August 2014
EC-186
2015 Rogue NAM
P0014 EVT CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Exhaust valve timing control solenoid valve
+
Resistance
Ground
(Continuity should not exist)
Terminal
1
2
EC
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
2.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-2
Remove exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between exhaust valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Check that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in exhaust valve
timing control solenoid valve.
NOTE:
Always replace O-ring when exhaust valve timing control
solenoid valve is removed.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
1.
2.
G
JMBIA0079ZZ
Revision: August 2014
EC-187
2015 Rogue NAM
P0030, P0031, P0032 A/F SENSOR 1 HEATER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0030, P0031, P0032 A/F SENSOR 1 HEATER
DTC Description
INFOID:0000000011277936
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0030
A/F SEN1 HTR (B1)
[Air fuel ratio (A/F) sensor 1 heater (bank
1)performance]
Deterioration in A/F sensor 1 heater performance.
(Voltage signal transmitted from A/F sensor 1 heater to ECM is higher/lower
than voltage in the normal range .)
P0031
A/F SEN1 HTR (B1)
[Air fuel ratio (A/F) sensor 1 heater (bank
1)control circuit low]
The current amperage in the A/F sensor 1 heater circuit is out of the normal
range.
(An excessively low voltage signal is sent to ECM through the A/F sensor
1 heater.)
P0032
A/F SEN1 HTR (B1)
[Air fuel ratio (A/F) sensor 1 heater (bank
1)control circuit high]
The current amperage in the A/F sensor 1 heater circuit is out of the normal
range.
(An excessively high voltage signal is sent to ECM through the A/F sensor
1 heater.)
POSSIBLE CAUSE
DTC P0030, P0031
Harness or connectors (A/F sensor 1 heater circuit is open or shorted.)
A/F sensor 1 heater
DTC P0032
Harness or connectors (A/F sensor 1 heater circuit is shorted.)
A/F sensor 1 heater
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than between 11 V at
idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-188, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277937
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Disconnect air fuel ratio (A/F) sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
Revision: August 2014
EC-188
2015 Rogue NAM
P0030, P0031, P0032 A/F SENSOR 1 HEATER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Voltage
Ground
Battery voltage
A/F sensor 1
Connector
Terminal
F18
EC
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Continuity
Connector
Terminal
Connector
Terminal
F18
F52
53
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
Check the A/F sensor 1 heater. Refer to EC-189, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
3.CHECK A/F SENSOR 1 HEATER
4.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize Lubricant
(commercial service tool).
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277938
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Check resistance between A/F sensor 1 terminals as per the following.
Revision: August 2014
>> INSPECTION END
1.
2.
3.
EC-189
2015 Rogue NAM
P0030, P0031, P0032 A/F SENSOR 1 HEATER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
A/F sensor 1
+
Resistance
1.8 - 2.44 [at 20C (68F)]
Terminal
1
2
(Continuity should not exist)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-190
2015 Rogue NAM
P0037, P0038 HO2S2 HEATER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0037, P0038 HO2S2 HEATER
DTC Description
INFOID:0000000011277939
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0037
P0038
EC
DTC detecting condition
HO2S2 HTR (B1)
(HO2S heater control circuit low bank 1
sensor 2)
The current amperage in the heated oxygen sensor 2 heater circuit is out
of the normal range.
(An excessively low voltage signal is sent to ECM through the heated oxygen sensor 2 heater.)
HO2S2 HTR (B1)
(HO2S heater control circuit high bank 1
sensor 2)
The current amperage in the heated oxygen sensor 2 heater circuit is out
of the normal range.
(An excessively high voltage signal is sent to ECM through the heated oxygen sensor 2 heater.)
POSSIBLE CAUSE
DTC P0037
Harness or connectors (Heated oxygen sensor 2 heater circuit is open or shorted.)
Heated oxygen sensor 2 heater
DTC P0038
Harness or connectors (Heated oxygen sensor 2 heater circuit is shorted.)
Heated oxygen sensor 2 heater
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
1.PRECONDITIONING
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-191, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
3.
4.
5.
6.
Diagnosis Procedure
INFOID:0000000011277940
1.CHECK HO2S2 POWER SUPPLY CIRCUIT
Revision: August 2014
EC-191
2015 Rogue NAM
P0037, P0038 HO2S2 HEATER
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
3. Turn ignition switch ON.
4. Check the voltage between HO2S2 harness connector and ground.
[QR25DE]
Voltage
Ground
Battery voltage
HO2S2
Connector
Terminal
F21
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.CHECK HO2S2 OUTPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between HO2S2 harness connector and ECM harness connector.
+
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F52
54
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK HEATED OXYGEN SENSOR 2 HEATER
Check the heated oxygen sensor 2 heater. Refer to EC-192, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277941
1.CHECK HEATED OXYGEN SENSOR 2 HEATER
1.
2.
3.
Turn ignition switch OFF.
Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
Check resistance between HO2S2 terminals as per the following.
Revision: August 2014
EC-192
2015 Rogue NAM
P0037, P0038 HO2S2 HEATER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Heated oxygen sensor 2
+
Resistance
3.3 - 4.4 [at 25C (77F)]
Terminal
4
EC
2
1
3
4
(Continuity should not exist)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
I
Revision: August 2014
EC-193
2015 Rogue NAM
P0075 INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0075 INTAKE VALVE TIMING CONTROL
DTC Description
INFOID:0000000011277942
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
INT/V TIM V/CIR-B1
(Intake valve control solenoid circuit bank 1)
ECM detects an abnormal voltage in the intake valve timing control solenoid valve control circuit.
ECM detects an abnormal voltage in the intake valve timing intermediate
lock control solenoid valve control circuit.
DTC No.
P0075
POSSIBLE CAUSE
Harness or connectors
Intake valve timing control solenoid valve circuit is open or shorted.
Intake valve timing intermediate lock control solenoid valve circuit is open or shorted.
Intake valve timing control solenoid valve
Intake valve timing intermediate lock control solenoid valve
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-194, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277943
1.CHECK INTAKE VALVE TIMING (IVT) CONTROL SOLENOID VALVE POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect IVT control solenoid valve harness connector.
Turn ignition switch ON.
Check the voltage between intake valve timing control solenoid valve harness connector and ground.
+
Voltage
Ground
Battery voltage
IVT control solenoid valve
Connector
Terminal
F25
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK IVT CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
Revision: August 2014
EC-194
2015 Rogue NAM
P0075 INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check the continuity between IVT control solenoid valve harness connector and IPDM E/R harness connector.
EC
IVT control solenoid valve
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F25
F35
78
C
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK IVT CONTROL SOLENOID VALVE GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between IVT control solenoid valve harness connector and ECM harness connector.
+
IVT control solenoid valve
ECM
G
Continuity
Connector
Terminal
Connector
Terminal
F25
F52
93
Existed
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK IVT CONTROL SOLENOID VALVE
Check the IVT control solenoid valve. Refer to EC-196, "Component Inspection (IVT Control Solenoid Valve)".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace IVT control solenoid valve. Refer to EM-49, "Exploded View".
5.CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE POWER SUPPLY
1.
2.
3.
Disconnect IVT intermediate lock control solenoid valve harness connector.
Turn ignition switch ON.
Check the voltage between IVT intermediate lock control solenoid valve harness connector and ground.
+
IVT intermediate lock control
solenoid valve
Connector
Terminal
F23
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 7.
NO
>> GO TO 6.
6.CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between IVT intermediate lock control solenoid valve harness connector and IPDM
E/R harness connector.
Revision: August 2014
EC-195
2015 Rogue NAM
P0075 INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
IVT intermediate lock control solenoid valve
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F23
F35
78
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
7.CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between IVT intermediate lock control solenoid valve harness connector and ECM
harness connector.
+
IVT intermediate lock control solenoid valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F23
F52
56
Existed
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE
Check the IVT intermediate lock control solenoid valve. Refer to EC-197, "Component Inspection (IVT Intermediate Lock Control Solenoid Valve)".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace IVT intermediate lock control solenoid valve. Refer to EM-69, "Exploded View".
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection (IVT Control Solenoid Valve)
INFOID:0000000011277944
1.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake valve timing control solenoid valve harness connector.
Check resistance between intake valve timing control solenoid valve terminals as follows.
Terminals
Resistance
1 and 2
7.0 - 7.5 [at 20C (68F)]
1 or 2 and ground
(Continuity should not exist)
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Revision: August 2014
EC-196
2015 Rogue NAM
P0075 INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II
Remove intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between intake valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Make sure that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing control
solenoid valve is removed.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
1.
2.
Component Inspection (IVT Intermediate Lock Control Solenoid Valve)
EC
D
JMBIA2107ZZ
INFOID:0000000011277945
1.CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-I
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake valve timing intermediate lock control solenoid valve harness connector.
Check resistance between intake valve timing intermediate lock control solenoid valve terminals as follows.
H
Terminals
Resistance
1 and 2
7.0 - 7.5 [at 20C (68F)]
1 or 2 and ground
(Continuity should not exist)
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace intake valve timing intermediate lock control solenoid valve. Refer to EM-49, "Exploded
View".
2.CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-II
Remove intake valve timing intermediate lock control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between intake valve timing intermediate lock
control solenoid valve terminals 1 and 2, and then interrupt it.
Make sure that the plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing intermediate lock control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing intermediate lock control solenoid valve is removed.
Is the inspection result normal?
JMBIA2107ZZ
YES >> INSPECTION END
NO
>> Replace intake valve timing intermediate lock control solenoid valve. Refer to EM-49, "Exploded
View".
1.
2.
Revision: August 2014
EC-197
2015 Rogue NAM
P0078 EVT CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0078 EVT CONTROL SOLENOID VALVE
DTC Description
INFOID:0000000011277946
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
EX V/T ACT/CIRC-B1
(Exhaust valve control solenoid circuit bank
1)
An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve.
DTC No.
P0078
POSSIBLE CAUSE
Harness or connectors (Exhaust valve timing control solenoid valve circuit is open or shorted.)
Exhaust valve timing control solenoid valve
FAIL-SAFE
Device fix mode
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-198, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277947
1.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect exhaust valve timing (EVT) control solenoid valve harness connector.
Turn ignition switch ON.
Check the voltage between exhaust valve timing control solenoid valve harness connector and ground.
+
EVT control solenoid valve
Connector
Terminal
F24
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
2.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Revision: August 2014
EC-198
2015 Rogue NAM
P0078 EVT CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
3. Check the continuity between EVT control solenoid valve harness connector and IPDM E/R harness connector.
+
EVT control solenoid valve
IPDM E/R
EC
Continuity
Connector
Terminal
Connector
Terminal
F24
F35
78
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVT control solenoid valve harness connector and ECM harness connector.
+
EVT control solenoid valve
ECM
Terminal
Connector
Terminal
F24
F52
94
Continuity
Connector
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE
Check the exhaust valve timing control solenoid valve. Refer to EC-186, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace exhaust valve timing control solenoid valve.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277948
1.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect exhaust valve timing control solenoid valve harness connector.
Check resistance between exhaust valve timing control solenoid valve terminals as per the following.
Exhaust valve timing control solenoid valve
+
Resistance
7.0 - 7.7 [at 20C (68F)]
Ground
(Continuity should not exist)
Terminal
1
1
2
Is the inspection result normal?
Revision: August 2014
EC-199
2015 Rogue NAM
P0078 EVT CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO
>> Replace exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
2.CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-2
Remove exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between exhaust valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Check that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in exhaust valve
timing control solenoid valve.
NOTE:
Always replace O-ring when exhaust valve timing control
solenoid valve is removed.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace exhaust valve timing control solenoid valve. Refer to EM-49, "Exploded View".
1.
2.
Revision: August 2014
EC-200
JMBIA0079ZZ
2015 Rogue NAM
P0101 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0101 MAF SENSOR
DTC Description
INFOID:0000000011277949
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
MAF SEN/CIRCUIT-B1
(Mass or volume air Flow A circuit range/
performance)
A high voltage from the sensor is sent to ECM under light load driving
condition.
A low voltage from the sensor is sent to ECM under heavy load driving
condition.
DTC No.
P0101
EC
POSSIBLE CAUSE
Harness or connectors (MAF sensor circuit is open or shorted.)
Intake air leaks
MAF sensor
EVAP control system pressure sensor
Intake air temperature sensor
Sensor power supply 2 circuit
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
Traveling control mode (Engine output control)
Device fix mode
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0101 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
Start engine and warm it up to normal operating temperature.
Drive the vehicle for at least 5 seconds under the following conditions:
CAUTION:
Always drive vehicle at safe speed.
O
Selector lever
Suitable position
Vehicle speed
40 km/h (25 MPH) or more
NOTE:
The gear must be fixed while driving the vehicle.
Keep the accelerator pedal as steady as possible during cruising.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-202, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-201
2015 Rogue NAM
P0101 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011277950
1.CHECK DTC PRIORITY
If DTC P0101 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK INTAKE SYSTEM
Check the following for connection.
Air duct
Vacuum hoses
Intake air passage between air duct and intake manifold
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Reconnect the parts.
3.CHECK MASS AIR FLOW (MAF) SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect MAF sensor harness connector.
Turn ignition switch ON.
Check the voltage between MAF sensor harness connector and ground.
+
Voltage
Ground
5V
MAF sensor
Connector
Terminal
F22
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
5.CHECK MAF SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between MAF sensor harness connector and ECM harness connector.
+
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
34
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK MAF SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between MAF sensor harness connector and ECM harness connector.
Revision: August 2014
EC-202
2015 Rogue NAM
P0101 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
MAF sensor
ECM
A
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
35
EC
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts
7.CHECK INTAKE AIR TEMPERATURE SENSOR
Check the intake air temperature sensor. Refer to EC-210, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace MAF sensor (with intake air temperature sensor). Refer to EM-26, "Exploded View".
8.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to EC-333, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
9.CHECK MAF SENSOR
Check the MAF sensor. Refer to EC-203, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Replace MAF sensor. Refer to EM-26, "Exploded View".
10.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277951
1.CHECK MASS AIR FLOW SENSOR-1
1.
2.
3.
4.
5.
With CONSULT
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Start engine and warm it up to normal operating temperature.
Connect CONSULT and select DATA MONITOR mode of ENGINE.
Select MASS AIR FLOW SENSOR (Hz) and check indication.
Monitor item
Condition
N
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
Revision: August 2014
EC-203
2015 Rogue NAM
P0101 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MASS AIR FLOW SENSOR
1. Turn ignition switch OFF.
2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
Crushed air ducts
Malfunctioning seal of air cleaner element
Uneven dirt of air cleaner element
Intake valve deposits
Improper specification of intake air system parts
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK MASS AIR FLOW SENSOR-2
1.
2.
3.
4.
With CONSULT
Repair or replace malfunctioning part.
Start engine and warm it up to normal operating temperature.
Connect CONSULT and select DATA MONITOR mode of ENGINE.
Select MASS AIR FLOW SENSOR (Hz) and check indication.
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 4.
4.CHECK MASS AIR FLOW SENSOR-3
1.
2.
3.
4.
5.
With CONSULT
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Start engine and warm it up to normal operating temperature.
Connect CONSULT and select DATA MONITOR mode of ENGINE.
Select MASS AIR FLOW SENSOR (Hz) and check indication.
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Clean or replace mass air flow sensor. Refer to EM-26, "Exploded View".
Revision: August 2014
EC-204
2015 Rogue NAM
P0102, P0103 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0102, P0103 MAF SENSOR
DTC Description
INFOID:0000000011277952
DTC DETECTION LOGIC
DTC No.
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0102
MAF SEN/CIRCUIT-B1
(Mass or volume air flow A circuit low)
An excessively low voltage from the mass air flow sensor is sent to ECM.
P0103
MAF SEN/CIRCUIT-B1
(Mass or volume air flow A circuit high)
An excessively high voltage from the mass air flow sensor is sent to ECM.
POSSIBLE CAUSE
DTC P0102
Harness or connectors (Mass air flow sensor circuit is open or shorted.)
Intake air leaks
Mass air flow sensor
Sensor power supply 2 circuit
DTC P0103
Harness or connectors (Mass air flow sensor circuit is open or shorted.)
Mass air flow sensor
Sensor power supply 2 circuit
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
Traveling control mode (Engine output control)
Device fix mode
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0102
3.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-1
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-206, "Diagnosis Procedure".
NO
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-2
Start engine and wait at least 5 seconds.
Check DTC.
Revision: August 2014
EC-205
1. Start engine and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-206, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
2015 Rogue NAM
P0102, P0103 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is DTC detected?
YES >> Proceed to EC-206, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277953
1.INSPECTION START
Confirm the detected DTC.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.CHECK INTAKE SYSTEM
Check the following for connection.
Air duct
Vacuum hoses
Intake air passage between air duct to intake manifold
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Reconnect the parts. Refer to EM-26, "Exploded View".
3.CHECK MAF SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect mass air flow (MAF) sensor harness connector.
Turn ignition switch ON.
Check the voltage between MAF sensor harness connector and ground.
+
Voltage
Ground
5V
MAF sensor
Connector
Terminal
F22
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
5.CHECK MAF SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between MAF sensor harness connector and ECM harness connector.
+
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
34
Existed
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK MAF SENSOR INPUT SIGNAL CIRCUIT
Revision: August 2014
EC-206
2015 Rogue NAM
P0102, P0103 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1. Check the continuity between MAF sensor harness connector and ECM harness connector.
A
+
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
35
EC
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.CHECK MAF SENSOR
Check the MAF sensor. Refer to EC-203, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace mass air flow sensor. Refer to EM-26, "Exploded View".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277954
1.CHECK MASS AIR FLOW SENSOR-1
I
With CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Start engine and warm it up to normal operating temperature.
4. Connect CONSULT and select DATA MONITOR mode of ENGINE.
5. Select MASS AIR FLOW SENSOR (Hz) and check indication.
K
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MASS AIR FLOW SENSOR
1. Turn ignition switch OFF.
2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.
Crushed air ducts
Malfunctioning seal of air cleaner element
Uneven dirt of air cleaner element
Intake valve deposits
Improper specification of intake air system parts
Is the inspection result normal?
YES >> GO TO 4.
Revision: August 2014
EC-207
2015 Rogue NAM
P0102, P0103 MAF SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> GO TO 3.
3.CHECK MASS AIR FLOW SENSOR-2
1.
2.
3.
4.
With CONSULT
Repair or replace malfunctioning part.
Start engine and warm it up to normal operating temperature.
Connect CONSULT and select DATA MONITOR mode of ENGINE.
Select MASS AIR FLOW SENSOR (Hz) and check indication.
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 4.
4.CHECK MASS AIR FLOW SENSOR-3
1.
2.
3.
4.
5.
With CONSULT
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Start engine and warm it up to normal operating temperature.
Connect CONSULT and select DATA MONITOR mode of ENGINE.
Select MASS AIR FLOW SENSOR (Hz) and check indication.
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Clean or replace mass air flow sensor. Refer to EM-26, "Exploded View".
Revision: August 2014
EC-208
2015 Rogue NAM
P0111 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0111 IAT SENSOR
DTC Description
INFOID:0000000011277955
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
IAT SENSOR 1 B1
(Intake air temperature sensor 1 circuit
range/performance bank 1)
P0111
DTC detecting condition
The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows
that the voltage signal of the IAT sensor is higher/lower than that of other
temperature sensors when the engine is started with its cold state.
POSSIBLE CAUSE
Harness or connectors (High or low resistance in the IAT sensor circuit)
IAT sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK INTAKE AIR TEMPERATURE (IAT) SENSOR
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Check that INT/A TEMP SEN indicates as per following condition.
Monitor item
INT/A TEMP SEN
Value
(Approx.)
Condition
Temperature [C (F)]
25 (77)
1.9 - 2.1 (V)
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Proceed to EC-210, "Diagnosis Procedure".
3.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, do not add fuel.
Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE
1.
Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between 10C (14F) and 35C (95F).
Revision: August 2014
EC-209
2015 Rogue NAM
P0111 IAT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the hood open.
3. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-210, "Diagnosis Procedure".
NO
>> INSPECTION END
[QR25DE]
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277956
1.CHECK INTAKE AIR TEMPERATURE (IAT) SENSOR
Check intake air temperature sensor. Refer toEC-210, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
2.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277957
1.CHECK INTAKE AIR TEMPERATURE SENSOR
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Check that INT/A TEMP SEN indicates as per following condition.
Monitor item
INT/A TEMP SEN
Value
(Approx.)
Condition
Temperature [C (F)]
25 (77)
1.9 - 2.1 (V)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
Revision: August 2014
EC-210
2015 Rogue NAM
P0112, P0113 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0112, P0113 IAT SENSOR
DTC Description
INFOID:0000000011277958
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0112
IAT SEN/CIRCUIT- B1
(Intake air temperature sensor 1 circuit low
bank 1)
An excessively low voltage from the intake air temperature sensor is sent
to ECM.
P0113
IAT SEN/CIRCUIT- B1
(Intake air temperature sensor 1 circuit high
bank 1)
An excessively high voltage from the intake air temperature sensor is sent
to ECM.
DTC No.
POSSIBLE CAUSE
Harness or connectors (Intake air temperature sensor circuit is open or shorted.)
Intake air temperature sensor
Sensor power supply 2 circuit
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
K
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-211, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277959
1.CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect mass air flow sensor (with intake air temperature sensor) harness connector.
Turn ignition switch ON.
Check the voltage between mass air flow sensor harness connector and ground.
+
MAF sensor
Connector
Terminal
F31
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
Revision: August 2014
EC-211
2015 Rogue NAM
P0112, P0113 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between mass air flow sensor harness connector and ECM harness connector.
+
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
33
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK INTAKE AIR TEMPERATURE SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between mass air flow sensor harness connector and ECM harness connector.
+
MAF sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F22
F51
34
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK INTAKE AIR TEMPERATURE SENSOR
Check the intake air temperature sensor. Refer to EC-210, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277960
1.CHECK INTAKE AIR TEMPERATURE SENSOR
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Check that INT/A TEMP SEN indicates as per following condition.
Monitor item
INT/A TEMP SEN
Value
(Approx.)
Condition
Temperature [C (F)]
25 (77)
1.9 - 2.1 (V)
Is the inspection result normal?
Revision: August 2014
EC-212
2015 Rogue NAM
P0112, P0113 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> INSPECTION END
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
EC
Revision: August 2014
EC-213
2015 Rogue NAM
P0116 ECT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0116 ECT SENSOR
DTC Description
INFOID:0000000011277961
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0116
ECT SENSOR
(Engine coolant temperature sensor 1 circuit range/performance)
DTC detecting condition
The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows
that the voltage signal of the ECT sensor is higher/lower than that of other
temperature sensors when the engine is started with its cold state.
POSSIBLE CAUSE
Harness or connectors (High or low resistance in the ECT sensor circuit)
ECT sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECT sensor harness connector.
Remove ECT sensor. Refer to CO-23, "Exploded View".
Check resistance between ECT sensor terminals by heating
with hot water as shown in the figure.
ECT sensor
Condition
Resistance (k)
Terminal
20 (68)
1
Temperature [C
(F)]
2.37 2.63
50 (122)
0.68 1.00
90 (194)
0.236 0.260
JMBIA0080ZZ
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Proceed to EC-215, "Diagnosis Procedure".
3.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, do not add fuel.
Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
Revision: August 2014
EC-214
2015 Rogue NAM
P0116 ECT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4.PERFORM DTC CONFIRMATION PROCEDURE
1.
Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between 10C (14F) and 35C (95F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the hood open.
3. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-215, "Diagnosis Procedure".
NO
>> INSPECTION END
5.CHECK INTERMITTENT INCIDENT
EC
Refer to GI-44, "Intermittent Incident".
G
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277962
1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR
Check ECT sensor. Refer to EC-215, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace ECT sensor. Refer to CO-23, "Exploded View".
2.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
K
>> INSPECTION END
Component Inspection
INFOID:0000000011277963
1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECT sensor harness connector.
Remove ECT sensor.
Check resistance between ECT sensor terminals by heating
with hot water as shown in the figure.
ECT sensor
Condition
Resistance
(k)
Terminal
Temperature [C (F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
P
JMBIA0080ZZ
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
Revision: August 2014
EC-215
2015 Rogue NAM
P0117, P0118 ECT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0117, P0118 ECT SENSOR
DTC Description
INFOID:0000000011277964
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0117
ECT SEN/CIRC
(Engine coolant temperature sensor 1 circuit low)
An excessively low voltage from the engine coolant temperature sensor is
sent to ECM.
P0118
ECT SEN/CIRC
(Engine coolant temperature sensor 1 circuit high)
An excessively high voltage from the engine coolant temperature sensor is
sent to ECM.
POSSIBLE CAUSE
Harness or connectors (Engine coolant temperature sensor circuit is open or shorted.)
Engine coolant temperature sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-216, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277965
1.CHECK ENGINE COOLANT TEMPERATURE SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect engine coolant temperature (ECT) sensor harness connector.
Turn ignition switch ON.
Check the voltage between ECT sensor harness connector and ground.
+
ECT sensor
Connector
Terminal
F61
Voltage
(Approx. )
Ground
5V
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK ENGINE COOLANT TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
Revision: August 2014
EC-216
2015 Rogue NAM
P0117, P0118 ECT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between ECT sensor harness connector and ECM harness connector.
+
ECT sensor
ECM
[QR25DE]
A
EC
Continuity
Connector
Terminal
Connector
Terminal
F61
F51
28
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK ENGINE COOLANT TEMPERATURE SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between ECT sensor harness connector and ECM harness connector.
+
ECT sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F61
F51
27
Existed
4. Also check harness for short to ground to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check the engine coolant temperature sensor. Refer to EC-215, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011277966
1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECT sensor harness connector.
Remove ECT sensor.
Revision: August 2014
EC-217
2015 Rogue NAM
P0117, P0118 ECT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
4. Check resistance between ECT sensor terminals by heating
with hot water as shown in the figure.
[QR25DE]
ECT sensor
Condition
Resistance
(k)
Terminal
Temperature [C (F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
JMBIA0080ZZ
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
Revision: August 2014
EC-218
2015 Rogue NAM
P0122, P0123 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0122, P0123 TP SENSOR
DTC Description
INFOID:0000000011277967
DTC DETECTION LOGIC
DTC No.
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0122
TP SEN 2/CIRC-B1
(Throttle/pedal position sensor/switch A
circuit low)
An excessively low voltage from the TP sensor 2 is sent to ECM.
P0123
TP SEN 2/CIRC-B1
(Throttle/pedal position sensor/switch A
circuit high)
An excessively high voltage from the TP sensor 2 is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (TP sensor 2 circuit is open or shorted.)
Electric throttle control actuator (TP sensor 2)
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
1.CHECK DTC PRIORITY
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
N
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-219, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277968
1.CHECK DTC PRIORITY
If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
Revision: August 2014
EC-219
2015 Rogue NAM
P0122, P0123 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Turn ignition switch ON.
Check the voltage between electric throttle control actuator harness connector and ground.
+
Voltage
(Approx.)
Ground
5V
Electric throttle control actuator
Connector
Terminal
F50
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
80
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK THROTTLE POSITION SENSOR 2 GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
78
Existed
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT
1.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
Revision: August 2014
EC-220
2015 Rogue NAM
P0122, P0123 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Electric throttle control actuator
ECM
A
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
77
EC
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK THROTTLE POSITION SENSOR
Check the throttle position sensor. Refer to EC-221, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
G
>> INSPECTION END
Component Inspection
INFOID:0000000011277969
1.CHECK THROTTLE POSITION SENSOR
1.
2.
3.
4.
5.
6.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
Turn ignition switch ON.
Set selector lever to D position.
Check the voltage between ECM harness connector terminals as per the following conditions.
Sensor 1
Condition
Voltage
Terminal
79
F52
Sensor 2
ECM
Connector
78
77
Accelerator
pedal
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-221
2015 Rogue NAM
P0125 ECT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0125 ECT SENSOR
DTC Description
INFOID:0000000011277970
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
ECT SENSOR
(Insufficient coolant temperature for closed
loop fuel control)
Voltage sent to ECM from the sensor is not practical, even when some
time has passed after starting the engine.
Engine coolant temperature is insufficient for closed loop fuel control.
DTC No.
P0125
POSSIBLE CAUSE
Harness or connectors (High resistance in the circuit)
Engine coolant temperature sensor
Thermostat
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0125 is displayed with DTC P0116 or P0117, first perform the trouble diagnosis for DTC P0116 or
P0117.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.CHECK ENGINE COOLANT TEMPERATURE SENSOR FUNCTION
With CONSULT
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Check that COOLAN TEMP/S is above 10C (50F).
With GST
Follow the procedure With CONSULT above.
Is it above 5C (41F)?
YES >> INSPECTION END
NO
>> GO TO 4.
1.
2.
3.
4.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Start engine and run it for 65 minutes at idle speed.
2. Check 1st tip DTC.
If COOLAN TEMP/S indication increases to more than 10C (50F) within 65 minutes, stop engine
because the test result will be OK.
CAUTION:
Be careful not to overheat engine.
With GST
Follow the procedure With CONSULT above.
Revision: August 2014
EC-222
2015 Rogue NAM
P0125 ECT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
Is 1st trip DTC detected?
YES >> Proceed to EC-223, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
[QR25DE]
A
INFOID:0000000011277971
1.CHECK DTC PRIORITY
EC
If DTC P0125 is displayed with DTC P0116 or P0117, first perform the trouble diagnosis for DTC P0116 or
P0117.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
Check the engine coolant temperature sensor. Refer to EC-215, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
When the engine is cold [lower than 70C (158F)] condition, grasp lower radiator hose and confirm the engine
coolant does not flow.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace thermostat. Refer to CO-21, "Removal and Installation".
Refer to GI-44, "Intermittent Incident".
2.CHECK ENGINE COOLANT TEMPERATURE SENSOR
3.CHECK THERMOSTAT OPERATION
4.CHECK INTERMITTENT INCIDENT
>> INSPECTION END
Component Inspection
INFOID:0000000011277972
1.CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECT sensor harness connector.
Remove ECT sensor.
Check resistance between ECT sensor terminals by heating
with hot water as shown in the figure.
M
ECT sensor
Condition
Resistance
(k)
Terminal
Temperature [C (F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
O
JMBIA0080ZZ
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
Revision: August 2014
EC-223
2015 Rogue NAM
P0127 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0127 IAT SENSOR
DTC Description
INFOID:0000000011277973
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0127
IAT SENSOR-B1
(Intake air temperature too high)
DTC detecting condition
Rationally incorrect voltage from the sensor is sent to ECM, compared with
the voltage signal from engine coolant temperature sensor.
POSSIBLE CAUSE
Harness or connectors (Intake air temperature sensor circuit is open or shorted.)
Intake air temperature sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road
test is expected to be easier, it is unnecessary to lift the vehicle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Wait until engine coolant temperature is less than 96C (205F)
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Check the engine coolant temperature.
If the engine coolant temperature is not less than 96C (205F), turn ignition switch OFF and cool down
engine.
NOTE:
Perform the following steps before engine coolant temperature is above 96C (205F).
2. Turn ignition switch ON.
3. Select DATA MONITOR mode of ENGINE using CONSULT
4. Start engine.
5. Hold vehicle speed at more than 70 km/h (43 MPH) for 100 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
6. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-224, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
-
Diagnosis Procedure
INFOID:0000000011277974
1.CHECK INTAKE AIR TEMPERATURE SENSOR
Check the intake air temperature sensor. Refer to EC-225, "Component Inspection".
Revision: August 2014
EC-224
2015 Rogue NAM
P0127 IAT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
2.CHECK INTERMITTENT INCIDENT
EC
Refer to GI-44, "Intermittent Incident".
C
>> INSPECTION END
Component Inspection
INFOID:0000000011277975
1.CHECK INTAKE AIR TEMPERATURE SENSOR
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect mass air flow sensor harness connector and reconnect it again.
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Check that INT/A TEMP SEN indicates as per following condition.
Monitor item
INT/A TEMP SEN
Value
(Approx.)
Condition
Temperature [C (F)]
25 (77)
1.9 - 2.1 (V)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-26, "Exploded
View".
Revision: August 2014
EC-225
2015 Rogue NAM
P0128 THERMOSTAT FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0128 THERMOSTAT FUNCTION
DTC Description
INFOID:0000000011277976
DTC DETECTION LOGIC
Engine coolant temperature has not risen enough to open the thermostat even though the engine has run long
enough.
This is due to a leak in the seal or the thermostat being stuck open.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
THERMSTAT FNCTN
[Coolant thermostat (coolant temperature
below thermostat regulating temperature)]
P0128
DTC detecting condition
The engine coolant temperature does not reach to specified temperature
even though the engine has run long enough.
POSSIBLE CAUSE
Thermostat
Leakage from sealing portion of thermostat
Engine coolant temperature sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
NOTE:
Never refuel before and during the following procedure.
1.CHECK DTC PRIORITY
If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303 or P0304, first perform the trouble diagnosis for DTC P0300, P0301, P0302, P0303 or P0304.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING-1
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PRECONDITIONING-2
1.
2.
With CONSULT
Turn ignition switch ON.
Check the following conditions:
Ambient temperature
10C (14F) or more
A/C switch
OFF
Blower fan switch
OFF
3.
4.
Select DATA MONITOR mode of ENGINE using CONSULT.
Check the following conditions:
COOLAN TEMP/S
10C 58C (14 136F)
Is the condition satisfied?
YES >> GO TO 4.
Revision: August 2014
EC-226
2015 Rogue NAM
P0128 THERMOSTAT FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> 1. Satisfy the condition.
2. GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
EC
Start engine.
Drive the vehicle until the following condition is satisfied.
CAUTION:
C
Always drive vehicle at safe speed.
STEP 1
Drive the vehicle under the conditions instructed below until the difference between COOLAN TEMP/S and
FUEL T/TMP SE becomes at least 26C (47F).
D
1.
2.
COOLAN TEMP/S
66C (151F) or less
FUEL T/TMP SE
Less than the value calculated by subtracting 26C (47F) from COOLAN
TEMP/S.*
*: Example
COOLAN TEMP/S
FUEL T/TMP SE
70C (158F)
44C (111F) or less
65C (149F)
39C (102F) or less
60C (140F)
34C (93F) or less
STEP 2
Drive the vehicle at 50 km/h (32 MPH) or more with the difference between COOLAN TEMP/S and FUEL
T/TMP SE maintained at 26C (47F) or more.
NOTE:
Keep the accelerator pedal as steady as possible during cruising.
STEP 3
Drive the vehicle at 50 km/h (32 MPH) or more until COOLAN TEMP/S increases by 6C (11F).
NOTE:
Keep the accelerator pedal as steady as possible during cruising.
Is the condition satisfied?
YES >> GO TO 5.
NO
>> GO TO 2.
5.PERFORM DTC CONFIRMATION PROCEDURE-2
CAUTION:
Always drive vehicle at safe speed.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-227, "Diagnosis Procedure".
NO
>> INSPECTION END
O
INFOID:0000000011277977
1.CHECK DTC PRIORITY
If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303 or P0304, first perform the trouble diagnosis for DTC P0300, P0301, P0302, P0303 or P0304.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
Revision: August 2014
67C (153F) or more
Diagnosis Procedure
With CONSULT
1. Drive the vehicle until the following condition is satisfied.
COOLAN TEMP/S
EC-227
2015 Rogue NAM
P0128 THERMOSTAT FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check the engine coolant temperature sensor. Refer to EC-228, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
3.CHECK THERMOSTAT
Check the thermostat. Refer to CO-21, "Removal and Installation".
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace thermostat.
Component Inspection
INFOID:0000000011277978
1.CHECK ENGINE COOLANT TEMPERATURE SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect engine coolant temperature sensor harness connector.
Remove engine coolant temperature sensor.
Check resistance between engine coolant temperature sensor
terminals by heating with hot water as shown in the figure.
Engine coolant temperature sensor
Condition
Resistance (k)
Terminal
Temperature [C
(F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
JMBIA0080ZZ
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
Revision: August 2014
EC-228
2015 Rogue NAM
P0130 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0130 A/F SENSOR 1
DTC Description
INFOID:0000000011277979
DTC DETECTION LOGIC
EC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal fluctuates according to fuel feedback control.
C
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
A/F SENSOR1 (B1)
(O2 sensor circuit bank 1 sensor 1)
P0130
DTC detecting condition
A
The A/F signal computed by ECM from the A/F sensor 1 signal is constantly in the range other than approx. 2.2 V.
The A/F signal computed by ECM from the A/F sensor 1 signal is constantly approx. 2.2 V.
POSSIBLE CAUSE
Harness or connectors (A/F sensor 1 circuit is open or shorted.)
A/F sensor 1
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
With CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Let it idle for 2 minutes.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-230, "Diagnosis Procedure".
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 7.
3.CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
1. Select A/F SEN1 (B1) in DATA MONITOR mode of ENGINE using CONSULT.
2. Check A/F SEN1 (B1) indication.
Does the indication fluctuates around 2.2 V?
YES >> GO TO 4.
NO
>> Proceed to EC-230, "Diagnosis Procedure".
4.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-1
1.
2.
3.
Select A/F SEN1 (B1) P1276 of A/F SEN1 in DTC WORK SUPPORT mode of ENGINE using CONSULT.
Touch START.
When the following conditions are met, TESTING will be displayed on the CONSULT screen.
Revision: August 2014
EC-229
2015 Rogue NAM
P0130 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 64 km/h (40 mph)
B/FUEL SCHDL
1.0 - 8.0 msec
Selector lever
D position
If TESTING is not displayed after 20 seconds, retry from step 2.
CAUTION:
Always drive vehicle at a safe speed.
Is TESTING displayed on CONSULT screen?
YES >> GO TO 5.
NO
>> Check A/F sensor 1 function again. GO TO 2.
5.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-2
Release accelerator pedal fully.
NOTE:
Never apply brake during releasing the accelerator pedal.
Which does TESTING change to?
COMPLETED>>GO TO 6.
OUT OF CONDITION>>Retry DTC CONFIRMATION PROCEDURE. GO TO 3.
6.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-3
Touch SELF-DIAG RESULT
Which is displayed on CONSULT screen?
YES >> INSPECTION END
NO
>> Proceed to EC-230, "Diagnosis Procedure".
7.PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
With GST
Start engine and warm it up to normal operating temperature.
Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in the suitable gear position.
Shift the selector lever to the D position, then release the accelerator pedal fully until the vehicle speed
decreases to 50 km/h (31 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Never apply brake during releasing the accelerator pedal.
4. Repeat steps 2 to 3 for five times.
5. Stop the vehicle and turn ignition switch OFF.
6. Wait at least 10 seconds and restart engine.
7. Repeat steps 2 to 3 for five times.
8. Stop the vehicle.
9. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-230, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
3.
Diagnosis Procedure
INFOID:0000000011277980
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
Revision: August 2014
EC-230
2015 Rogue NAM
P0130 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Voltage
Ground
Battery voltage
A/F sensor 1
Connector
Terminal
F18
EC
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
+
A/F sensor 1
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F18
F35
75
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
1.
2.
3.
3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
A/F sensor 1
ECM
Connector
Terminal
Connector
F18
4.
Continuity
41
F51
Terminal
45
Existed
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
A/F sensor 1
Connector
Continuity
Terminal
1
F18
Ground
Not existed
+
ECM
Connector
Continuity
Ground
Not existed
Terminal
F51
41
45
5. Also check harness for short to power.
Is the inspection result normal?
Revision: August 2014
EC-231
2015 Rogue NAM
P0130 A/F SENSOR 1
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
[QR25DE]
4.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-232
2015 Rogue NAM
P0131 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0131 A/F SENSOR 1
DTC Description
INFOID:0000000011277981
DTC DETECTION LOGIC
EC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal is not inordinately low.
DTC detecting condition
A/F SENSOR1 (B1)
(O2 sensor circuit low voltage bank 1 sensor 1)
The A/F signal computed by ECM from the A/F sensor 1 signal is constantly
approx. 0 V.
DTC No.
P0131
CONSULT screen terms
(Trouble diagnosis content)
POSSIBLE CAUSE
Harness or connectors (A/F sensor 1 circuit is open or shorted.)
A/F sensor 1
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.
>> GO TO 2.
2.CHECK A/F SENSOR FUNCTION
K
With CONSULT
Start engine and warm it up to normal operating temperature.
Select A/F SEN1 (B1) in DATA MONITOR mode of ENGINE using CONSULT.
Check A/F SEN1 (B1) indication.
With GST
Follow the procedure With CONSULT above.
Is the indication constantly approx. 0 V?
YES >> Proceed to EC-234, "Diagnosis Procedure".
NO
>> GO TO 3.
1.
2.
3.
3.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch OFF, wait at least 10 seconds and then restart engine.
Drive and accelerate vehicle to more than 40 km/h (25 MPH) within 20 seconds after restarting engine.
CAUTION:
Always drive vehicle at a safe speed.
3. Maintain the following conditions for about 20 consecutive seconds.
1.
2.
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 40 km/h (25 mph)
B/FUEL SCHDL
1.5 - 9.0 msec
Selector lever
Suitable position
NOTE:
Revision: August 2014
EC-233
2015 Rogue NAM
P0131 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Keep the accelerator pedal as steady as possible during the cruising.
If this procedure is not completed within 1 minute after restarting engine at step 1, return to step
1.
4. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-234, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277982
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
+
Voltage
Ground
Battery voltage
A/F sensor 1
Connector
Terminal
F18
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
+
A/F sensor 1
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F18
F35
75
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Connector
F18
4.
Terminal
1
2
Connector
F51
Continuity
Terminal
41
45
Existed
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
Revision: August 2014
EC-234
2015 Rogue NAM
P0131 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
A/F sensor 1
Connector
Continuity
Terminal
1
F18
EC
Ground
Not existed
C
+
ECM
Connector
Continuity
Ground
Not existed
Terminal
F51
41
45
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
L
Revision: August 2014
EC-235
2015 Rogue NAM
P0132 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0132 A/F SENSOR 1
DTC Description
INFOID:0000000011277983
DTC DETECTION LOGIC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal is not inordinately high.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
A/F SENSOR1 (B1)
(O2 sensor circuit high voltage bank 1 sensor 1)
The A/F signal computed by ECM from the A/F sensor 1 signal is constantly
approx. 5 V.
DTC No.
P0132
POSSIBLE CAUSE
Harness or connectors (A/F sensor 1 circuit is open or shorted.)
A/F sensor 1
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.
>> GO TO 2.
2.CHECK A/F SENSOR FUNCTION
With CONSULT
Start engine and warm it up to normal operating temperature.
Select A/F SEN1 (B1) in DATA MONITOR mode of ENGINE using CONSULT.
Check A/F SEN1 (B1) indication.
With GST
Follow the procedure With CONSULT above.
Is the indication constantly approx. 5 V?
YES >> Proceed to EC-237, "Diagnosis Procedure".
NO
>> GO TO 3.
1.
2.
3.
3.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch OFF, wait at least 10 seconds and then restart engine.
Drive and accelerate vehicle to more than 40 km/h (25 MPH) within 20 seconds after restarting engine.
CAUTION:
Always drive vehicle at a safe speed.
3. Maintain the following conditions for about 20 consecutive seconds.
1.
2.
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 40 km/h (25 mph)
B/FUEL SCHDL
1.5 - 9.0 msec
Selector lever
Suitable position
NOTE:
Revision: August 2014
EC-236
2015 Rogue NAM
P0132 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Keep the accelerator pedal as steady as possible during the cruising.
If this procedure is not completed within 1 minute after restarting engine at step 1, return to step A
1.
4. Check 1st trip DTC.
With GST
EC
Follow the procedure With CONSULT above.
Is 1st trip DTC is detected?
YES >> Proceed to EC-237, "Diagnosis Procedure".
C
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277984
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
F
+
A/F sensor 1
Connector
Terminal
F18
Voltage
G
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
+
A/F sensor 1
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F18
F35
75
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Connector
F18
4.
Terminal
1
2
Connector
F51
Continuity
45
Existed
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
Revision: August 2014
EC-237
Terminal
41
2015 Rogue NAM
P0132 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
A/F sensor 1
Connector
Continuity
Ground
Not existed
Continuity
Ground
Not existed
Terminal
1
F18
+
ECM
Connector
F51
Terminal
41
45
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-238
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0137 HO2S2
DTC Description
INFOID:0000000011277985
DTC DETECTION LOGIC
EC
The heated oxygen sensor 2 has a much longer switching time
between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the
longer switching time. To judge the malfunctions of heated oxygen
sensor 2, ECM monitors whether the maximum voltage of the sensor
is sufficiently high during the various driving condition such as fuelcut.
E
JPBIA5997ZZ
F
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
HO2S2 (B1)
(O2 sensor circuit low voltage bank 1 sensor 2)
The maximum voltage from the heated oxygen sensor 2 is not reached to
the specified voltage.
DTC No.
P0137
POSSIBLE CAUSE
Harness or connectors (Heated oxygen sensor 2 circuit is open or shorted.)
Heated oxygen sensor 2
Fuel pressure
Fuel injector
Intake air leaks
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 5.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
For better results, perform DTC WORK SUPPORT at a temperature of 0 to 30C (32 to 86F).
>> GO TO 3.
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Revision: August 2014
EC-239
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
3.
4.
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
5. Let engine idle for 1 minute.
6. Make sure that COOLAN TEMP/S indicates more than 70C (158F).
If not, warm up engine and go to next step when COOLAN TEMP/S indication reaches 70C (158F).
7. Open engine hood.
8. Select HO2S2 (B1) P1147 of HO2S2 in DTC WORK SUPPORT mode of ENGINE using CONSULT.
9. Follow the instruction of CONSULT.
NOTE:
It will take at most 10 minutes until COMPLETED is displayed.
10. Touch SELF-DIAG RESULT.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to EC-241, "Diagnosis Procedure".
CAN NOT BE DIAGNOSED>>GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1.
2.
Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
Perform DTC CONFIRMATION PROCEDURE again.
>> GO TO 3.
5.PERFORM COMPONENT FUNCTION CHECK-1
1.
2.
3.
4.
5.
Without CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Check the voltage between ECM harness connector and ground as per the following condition.
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
6.PERFORM COMPONENT FUNCTION CHECK-2
Check the voltage between ECM harness connector and ground as per the following condition.
ECM
Connector
F51
Condition
Voltage
23
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 7.
7.PERFORM COMPONENT FUNCTION CHECK-3
Check the voltage between ECM harness connector and ground as per the following condition.
Revision: August 2014
EC-240
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
+
Connector
Condition
Voltage
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
Terminal
F51
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-241, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011277986
1.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 detected? Is it difficult to start engine?
YES >> Perform trouble diagnosis for DTC P0171. Refer to EC-263, "DTC Description".
NO
>> GO TO 2.
2.CHECK HO2S2 GROUND CIRCUIT
1.
2.
3.
4.
HO2S2
ECM
I
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
23
Existed
3.CHECK HO2S2 INPUT SIGNAL CIRCUIT
2.
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
1.
Turn ignition switch OFF.
Disconnect heated oxygen sensor 2 (HO2S2) harness connector.
Disconnect ECM harness connector.
Check the continuity between HO2S2 harness connector and ECM harness connector.
+
EC
Check the continuity between HO2S2 harness connector and ECM harness connector.
M
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
22
Existed
Check the continuity between HO2S2 harness connector and ground, or ECM harness connector and
ground.
+
HO2S2
Connector
Terminal
F21
Revision: August 2014
Continuity
Ground
Not existed
EC-241
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
ECM
Connector
Terminal
F51
22
Continuity
Ground
Not existed
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK HEATED OXYGEN SENSOR 2
Check the heated oxygen sensor 2. Refer to EC-242, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 5.
5.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2.
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Component Inspection
INFOID:0000000011277987
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 3.
2.CHECK HEATED OXYGEN SENSOR 2
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Select FUEL INJECTION in ACTIVE TEST mode of ENGINE using CONSULT, and select HO2S2
(B1) as the monitor item with CONSULT.
7. Check HO2S2 (B1) at idle speed when adjusting FUEL INJECTION to 25%.
1.
2.
3.
4.
5.
6.
JPBIA5998GB
HO2S2 (B1) should be above 0.73 V at least once when the FUEL INJECTION is + 25%.
HO2S2 (B1) should be below 0.18 V at least once when the FUEL INJECTION is 25%.
Revision: August 2014
EC-242
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
3.CHECK HEATED OXYGEN SENSOR 2-1
Without CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
4. Let engine idle for 1 minute.
5. Check the voltage between ECM harness connector and ground as per the following condition.
EC
D
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 4.
4.CHECK HEATED OXYGEN SENSOR 2-2
Check the voltage between ECM harness connector and ground as per the following condition.
I
ECM
Connector
F51
Condition
Voltage
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Terminal
22
23
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 5.
Check the voltage between ECM harness connector and ground as per the following condition.
5.CHECK HEATED OXYGEN SENSOR 2-3
ECM
Connector
F51
Condition
Voltage
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
6.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Revision: August 2014
EC-243
2015 Rogue NAM
P0137 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-244
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0138 HO2S2
DTC Description
INFOID:0000000011277988
DTC DETECTION LOGIC
EC
The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/
F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching
time.
MALFUNCTION A
To judge the malfunctions of heated oxygen sensor 2, ECM monitors
whether the voltage is unusually high during the various driving condition such as fuel-cut.
F
PBIB1848E
MALFUNCTION B
To judge the malfunctions of heated oxygen sensor 2, ECM monitors
whether the minimum voltage of sensor is sufficiently low during the
various driving condition such as fuel-cut.
J
PBIB2376E
K
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0138
HO2S2 (B1)
(O2 sensor circuit high voltage bank 1 sensor 2)
DTC detecting condition
A
An excessively high voltage from the sensor is sent to ECM.
The minimum voltage from the sensor is not reached to the specified
voltage.
POSSIBLE CAUSE
DTC P0138 - A
Harness or connectors (The sensor circuit is open or shorted.)
Heated oxygen sensor 2
DTC P0138 - B
Harness or connectors (The sensor circuit is open or shorted.)
Heated oxygen sensor 2
Fuel pressure
Fuel injector
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
Revision: August 2014
EC-245
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
4. Let engine idle for 2 minutes.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-247, "Diagnosis Procedure".
NO-1 >> With CONSULT: GO TO 3.
NO-2 >> Without CONSULT: GO TO 5.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
NOTE:
For better results, perform DTC WORK SUPPORT at a temperature of 0 to 30C (32 to 86F).
1. Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5. Let engine idle for 1 minute.
6. Make sure that COOLAN TEMP/S indication is more than 70C (158F).
If not, warm up engine and go to next step when COOLAN TEMP/S indication reaches 70C (158F).
7. Open engine hood.
8. Select HO2S2 (B1) P1146 of HO2S2 in DTC WORK SUPPORT mode of ENGINE using CONSULT.
9. Follow the instruction of CONSULT.
NOTE:
It will take at most 10 minutes until COMPLETED is displayed.
10. Touch SELF-DIAG RESULT.
Which is displayed on CONSULT
OK
>> INSPECTION END
NG
>> Proceed to EC-247, "Diagnosis Procedure".
CAN NOT BE DIAGNOSED>>GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B AGAIN
1.
2.
Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
Perform DTC confirmation procedure again.
>> GO TO 3.
5.PERFORM COMPONENT FUNCTION CHECK-1
1.
2.
3.
4.
5.
Without CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Check the voltage between ECM harness connector and ground as per the following condition.
Revision: August 2014
EC-246
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
EC
6.PERFORM COMPONENT FUNCTION CHECK-2
Check the voltage between ECM harness connector and ground as per the following condition.
E
ECM
Connector
F51
Condition
Voltage
23
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 7.
7.PERFORM COMPONENT FUNCTION CHECK-3
Check the voltage between ECM harness connector and ground as per the following condition.
I
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-247, "Diagnosis Procedure".
Diagnosis Procedure
L
INFOID:0000000011277989
1.INSPECTION START
Confirm the detected malfunction (A or B). Refer to EC-245, "DTC Description".
Which malfunction is detected?
A
>> GO TO 2.
B
>> GO TO 7.
2.CHECK HO2S2 CONNECTOR FOR WATER
1.
2.
3.
Turn ignition switch OFF.
Disconnect heated oxygen sensor 2 harness connector.
Check connectors for water.
Water should not exist.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK HO2S2 GROUND CIRCUIT
Revision: August 2014
EC-247
2015 Rogue NAM
P0138 HO2S2
< DTC/CIRCUIT DIAGNOSIS >
1. Disconnect ECM harness connector.
2. Check the continuity between HO2S2 harness connector and ECM harness connector.
+
HO2S2
ECM
[QR25DE]
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
23
Existed
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK HO2S2 INPUT SIGNAL CIRCUIT
1.
2.
Check the continuity between HO2S2 harness connector and ECM harness connector.
+
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
22
Existed
Check the continuity between HO2S2 harness connector and ground, or ECM harness connector and
ground.
+
HO2S2
Connector
Terminal
F21
Continuity
Ground
Not existed
Continuity
Ground
Not existed
+
ECM
Connector
Terminal
F51
22
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK HEATED OXYGEN SENSOR 2
Check the heated oxygen sensor 2. Refer to EC-250, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 6.
6.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-248
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
7.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0172 detected? Is it difficult to start engine?
YES >> Perform trouble diagnosis for DTC P0172. Refer to EC-268, "DTC Description".
NO
>> GO TO 8.
8.CHECK HO2S2 GROUND CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect heated oxygen sensor 2 harness connector.
Disconnect ECM harness connector.
Check the continuity between HO2S2 harness connector and ECM harness connector.
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
23
Existed
9.CHECK HO2S2 INPUT SIGNAL CIRCUIT
2.
EC
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
1.
Check the continuity between HO2S2 harness connector and ECM harness connector.
I
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
22
J
Existed
Check the continuity between HO2S2 harness connector and ground, or ECM harness connector and
ground.
+
HO2S2
Connector
Terminal
F21
Continuity
Ground
Not existed
Continuity
Ground
Not existed
+
ECM
Connector
Terminal
F51
22
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.CHECK HEATED OXYGEN SENSOR 2
Check the heated oxygen sensor 2. Refer to EC-250, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 11.
Revision: August 2014
EC-249
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
11.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Component Inspection
INFOID:0000000011277990
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 3.
2.CHECK HEATED OXYGEN SENSOR 2
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Select FUEL INJECTION in ACTIVE TEST mode of ENGINE using CONSULT, and select HO2S2
(B1) as the monitor item with CONSULT.
7. Check HO2S2 (B1) at idle speed when adjusting FUEL INJECTION to 25%.
1.
2.
3.
4.
5.
6.
JPBIA5998GB
HO2S2 (B1) should be above 0.73 V at least once when the FUEL INJECTION is + 25%.
HO2S2 (B1) should be below 0.18 V at least once when the FUEL INJECTION is 25%.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
3.CHECK HEATED OXYGEN SENSOR 2-1
1.
2.
3.
4.
5.
Without CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Check the voltage between ECM harness connector and ground as per the following condition.
Revision: August 2014
EC-250
2015 Rogue NAM
P0138 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
EC
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 4.
Check the voltage between ECM harness connector and ground as per the following condition.
4.CHECK HEATED OXYGEN SENSOR 2-2
ECM
Connector
F51
Condition
Voltage
23
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 5.
5.CHECK HEATED OXYGEN SENSOR 2-3
Check the voltage between ECM harness connector and ground as per the following condition.
J
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
6.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-251
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0139 HO2S2
DTC Description
INFOID:0000000011277991
DTC DETECTION LOGIC
The heated oxygen sensor 2 has a much longer switching time
between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst 1 causes the longer
switching time. To judge the malfunctions of heated oxygen sensor
2, ECM monitors whether the switching response of the sensor's
voltage is faster than specified during various driving conditions such
as fuel cut.
SEF302U
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0139
HO2S2 (B1)
(O2 sensor circuit slow response bank 1
sensor 2)
DTC detecting condition
The switching time between rich and lean of a heated oxygen sensor 2 signal delays more than the specified time computed by ECM.
POSSIBLE CAUSE
Harness or connectors (The sensor circuit is open or shorted.)
Heated oxygen sensor 2
Fuel system
EVAP system
Intake air system
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 7.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
For better results, perform DTC WORK SUPPORT at a temperature of 0 to 30C (32 to 86F).
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
3.
4.
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to the normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Revision: August 2014
EC-252
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
5. Turn ignition switch OFF and wait at least 10 seconds.
6. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load. A
7. Let engine idle for 1 minute.
8. Make sure that COOLAN TEMP/S indicates more than 70C (158F).
9. Drive the vehicle in a proper at 60 km/h (38MPH) and maintain the speed.
EC
CAUTION:
Always drive vehicle at a safe speed.
10. Release the accelerator pedal fully at least 5 seconds.
CAUTION:
C
Enable engine brake.
Always drive carefully.
Never apply brake when releasing the accelerator pedal.
D
11. Repeat step 9 and 10 at least 8 times.
12. Check the following item of DATA MONITOR.
Data monitor item
HO2 S2 DIAG1 (B1)
HO2 S2 DIAG2 (B1)
Status
CMPLT
Is CMPLT displayed on CONSULT screen?
YES >> GO TO 6.
NO-1: CMPLT is not displayed on DIAG 1>>Perform DTC confirmation procedure again.
NO-2: CMPLT is not displayed on DIAG 2>>GO TO 4.
4.PERFORM DTC WORK SUPPORT
1.
2.
3.
Open engine hood.
Select HO2S2 (B1) P0139 in DTC WORK SUPPORT mode of ENGINE using CONSULT.
Start engine and follow the instruction of CONSULT display.
NOTE:
It will take at most 10 minutes until COMPLETED is displayed.
Is COMPLETED displayed on CONSULT screen?
YES >> GO TO 6.
NO
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1.
2.
Turn ignition switch OFF and leave the vehicle in a cool place (soak the vehicle).
Perform DTC confirmation procedure again.
>> GO TO 3.
6.PERFORM SELF-DIAGNOSIS
M
With CONSULT
Perform ECM self-diagnosis.
Is DTC P0139 detected?
YES >> Proceed to EC-254, "Diagnosis Procedure".
NO
>> INSPECTION END
7.PERFORM COMPONENT FUNCTION CHECK-1
Without CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
4. Let engine idle for 1 minute.
5. Check the voltage between ECM harness connector and ground as per the following condition.
Revision: August 2014
EC-253
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 8.
8.PERFORM COMPONENT FUNCTION CHECK-2
Check the voltage between ECM harness connector and ground as per the following condition.
ECM
Connector
F51
Condition
Voltage
23
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 9.
9.PERFORM COMPONENT FUNCTION CHECK-3
Check the voltage between ECM harness connector and ground as per the following condition.
ECM
Connector
F51
Condition
Voltage
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-241, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011277992
1.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P0172 detected? Is it difficult to start engine?
YES >> Perform trouble diagnosis for DTC P0171 or P0172. Refer to EC-263, "DTC Description" or EC268, "DTC Description".
NO
>> GO TO 2.
2.CHECK HO2S2 GROUND CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect heated oxygen sensor 2 harness connector.
Disconnect ECM harness connector.
Check the continuity between HO2S2 harness connector and ECM harness connector.
Revision: August 2014
EC-254
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
HO2S2
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
23
EC
Existed
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK HO2S2 INPUT SIGNAL CIRCUIT
1.
Check the continuity between HO2S2 harness connector and ECM harness connector.
E
+
HO2S2
2.
ECM
Continuity
Connector
Terminal
Connector
Terminal
F21
F51
22
F
Existed
Check the continuity between HO2S2 harness connector and ground, or ECM harness connector and
ground.
+
HO2S2
Connector
Terminal
F21
Continuity
Ground
Not existed
Continuity
Ground
Not existed
+
ECM
Connector
Terminal
F51
22
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK HEATED OXYGEN SENSOR 2
Check the heated oxygen sensor 2. Refer to EC-256, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to EX-5, "Exploded View".
NO
>> GO TO 5.
5.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-255
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Component Inspection
INFOID:0000000011277993
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 3.
2.CHECK HEATED OXYGEN SENSOR 2
With CONSULT
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Select FUEL INJECTION in ACTIVE TEST mode of ENGINE using CONSULT, and select HO2S2
(B1) as the monitor item with CONSULT.
7. Check HO2S2 (B1) at idle speed when adjusting FUEL INJECTION to 25%.
1.
2.
3.
4.
5.
6.
JPBIA5998GB
HO2S2 (B1) should be above 0.73 V at least once when the FUEL INJECTION is + 25%.
HO2S2 (B1) should be below 0.18 V at least once when the FUEL INJECTION is 25%.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
3.CHECK HEATED OXYGEN SENSOR 2-1
1.
2.
3.
4.
5.
Without CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
Let engine idle for 1 minute.
Check the voltage between ECM harness connector and ground as per the following condition.
ECM
Connector
F51
Condition
Voltage
Terminal
22
23
Revving up to 4,000 rpm under no
load at least 10 times
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 4.
4.CHECK HEATED OXYGEN SENSOR 2-2
Check the voltage between ECM harness connector and ground as per the following condition.
Revision: August 2014
EC-256
2015 Rogue NAM
P0139 HO2S2
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Connector
F51
Condition
Voltage
Keeping engine speed at idle for 10
minutes
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Terminal
22
23
EC
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 5.
Check the voltage between ECM harness connector and ground as per the following condition.
5.CHECK HEATED OXYGEN SENSOR 2-3
ECM
Connector
F51
Condition
Voltage
23
Coasting from 80 km/h (50 MPH) in
D position
The voltage should be above 0.73 V
at least once during this procedure.
The voltage should be below 0.18 V
at least once during this procedure.
Terminal
22
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 6.
6.REPLACE HEATED OXYGEN SENSOR 2
Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-257
2015 Rogue NAM
P014C, P014D, P015A, P015B, A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P014C, P014D, P015A, P015B, A/F SENSOR 1
DTC Description
INFOID:0000000011277994
DTC DETECTION LOGIC
To judge malfunctions, this diagnosis measures response time of the A/F signal computed by ECM from the A/
F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel feedback control constant, and the A/F sensor 1 temperature index. Judgment is based on whether the compensated time (the A/F
signal cycling time index) is inordinately long or not.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P014C
A/F SENSOR1 (B1)
(O2 sensor slow response - rich to lean
bank 1 sensor 1)
P014D
A/F SENSOR1 (B1)
(O2 sensor slow response - lean to rich
bank 1 sensor 1)
P015A
A/F SENSOR1 (B1)
(O2 sensor delayed response - rich to lean
bank 1 sensor 1)
P015B
A/F SENSOR1 (B1)
(O2 sensor delayed response - lean to rich
bank 1 sensor 1)
DTC detecting condition
The response time of a A/F sensor 1 signal delays more than the specified time computed by ECM.
POSSIBLE CAUSE
Harness or connectors (The A/F sensor 1 circuit is open or shorted.)
A/F sensor 1
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 6.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
2.
3.
4.
5.
6.
7.
8.
9.
With CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1minute under no load.
Let engine idle for 1 minute.
Increase the engine speed up to about 3,600 rpm and keep it for 10 seconds.
Fully release accelerator pedal and then let engine idle for about 1 minute.
Check the items status of DATA MONITOR as follows.
NOTE:
If PRSNT changed to ABSNT, refer to EC-160, "Component Function Check".
Revision: August 2014
EC-258
2015 Rogue NAM
P014C, P014D, P015A, P015B, A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Data monitor item
Status
A/F SEN1 DIAG3 (B1)
PRSNT
Is PRSNT displayed on CONSULT screen?
YES >> GO TO 4.
NO
>> GO TO 3.
EC
3.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
Perform DTC confirmation procedure-1 again.
Is PRSNT displayed on CONSULT screen?
YES >> GO TO 4.
NO
>> Refer to EC-160, "Component Function Check".
4.PERFORM DTC CONFIRMATION PROCEDURE-2
1.
2.
With CONSULT
Wait for about 20 seconds at idle.
Check the items status of DATA MONITOR as follows.
NOTE:
If CMPLT changed to INCMP, refer to EC-160, "Component Function Check".
Data monitor item
A/F SEN1 DIAG1 (B1)
A/F SEN1 DIAG2 (B1)
Status
CMPLT
Is CMPLT displayed on CONSULT screen?
YES >> GO TO 5.
NO
>> Refer to EC-160, "Component Function Check".
5.PERFORM SELF-DIAGNOSIS
With CONSULT
Check the SELF-DIAG RESULT.
Is any DTC detected?
YES >> Proceed to EC-260, "Diagnosis Procedure".
NO
>> INSPECTION END
6.CHECK AIR-FUEL RATIO SELF-LEARNING VALUE
With GST
1. Start engine and warm it up to normal operating temperature.
2. Select Service $01 with GST.
3. Calculate the total value of Short term fuel trim and Long term fuel trim indications.
Is the total percentage within 15%?
YES >> GO TO 8.
NO
>> GO TO 7.
7.DETECT MALFUNCTIONING PART
Check the following.
Intake air leaks
Exhaust gas leaks
Incorrect fuel pressure
Lack of fuel
Fuel injector
Incorrect PCV hose connection
PCV valve
Mass air flow sensor
Revision: August 2014
EC-259
2015 Rogue NAM
P014C, P014D, P015A, P015B, A/F SENSOR 1
< DTC/CIRCUIT DIAGNOSIS >
>> Repair or replace malfunctioning part.
[QR25DE]
8.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
5. Let engine idle for 1 minute.
6. Increase the engine speed up to about 3,600 rpm and keep it for 10 seconds.
7. Fully release accelerator pedal and then let engine idle for about 1 minute.
8. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-260, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277995
1.RETIGHTEN A/F SENSOR 1
Loosen and retighten the A/F sensor 1. Refer to EM-32, "Exploded View".
>> GO TO 2.
2.CHECK EXHAUST GAS LEAK
1.
2.
Start engine and run it at idle.
Listen for an exhaust gas leak before three way catalyst (manifold).
PBIB1216E
Is exhaust gas leak detected?
YES >> Repair or replace.
NO
>> GO TO 3.
3.CHECK FOR INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES >> Repair or replace.
NO
>> GO TO 4.
4.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1.
2.
Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P172 detected? Is it difficult to start engine?
YES >> Perform trouble diagnosis for DTC P0171 or P0172. Refer to EC-263, "DTC Description" or EC268, "DTC Description".
NO
>> GO TO 5.
5.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Disconnect A/F sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
Revision: August 2014
EC-260
2015 Rogue NAM
P014C, P014D, P015A, P015B, A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
A/F sensor 1
Connector
Terminal
F18
Voltage
Ground
Battery voltage
EC
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Connector
Terminal
1
F18
4.
Connector
Continuity
41
45
Terminal
F51
Existed
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
+
A/F sensor 1
Connector
Continuity
Ground
Not existed
Continuity
Ground
Not existed
Terminal
1
F18
+
ECM
Connector
Terminal
F51
41
45
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
7.CHECK AIR FUEL RATIO (A/F) SENSOR 1 HEATER
Refer to EC-189, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> GO TO 11.
8.CHECK MASS AIR FLOW SENSOR
Refer to EC-203, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace mass air flow sensor. Refer to EM-26, "Exploded View".
9.CHECK PCV VALVE
Revision: August 2014
EC-261
2015 Rogue NAM
P014C, P014D, P015A, P015B, A/F SENSOR 1
< DTC/CIRCUIT DIAGNOSIS >
Refer to EC-501, "Inspection".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Repair or replace PCV valve. Refer to EC-14, "Component Parts Location".
[QR25DE]
10.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 11.
NO
>> Repair or replace.
11.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
>> INSPECTION END
Revision: August 2014
EC-262
2015 Rogue NAM
P0171 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0171 FUEL INJECTION SYSTEM FUNCTION
DTC Description
INFOID:0000000011277996
DTC DETECTION LOGIC
EC
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual mixture ratio can be brought closely to the
theoretical mixture ratio based on the mixture ratio feedback signal from the A/F sensors 1. The ECM calculates the necessary compensation to correct the offset between the actual and the theoretical ratios.
In case the amount of the compensation value is extremely large (The actual mixture ratio is too lean.), the
ECM judges the condition as the fuel injection system malfunction and lights up the MIL (2 trip detection logic).
Sensor
Input signal to ECM
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
A/F sensor 1
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
FUEL SYS-LEAN-B1
(System too lean bank 1)
P0171
ECM function
Fuel injection control
Actuator
Fuel injector
E
DTC detecting condition
Fuel injection system does not operate properly.
The amount of mixture ratio compensation is too large. (The mixture ratio
is too lean.)
POSSIBLE CAUSE
Intake air leaks
A/F sensor 1
Fuel injector
Exhaust gas leaks
Incorrect fuel pressure
Lack of fuel
Mass air flow sensor
Incorrect PCV hose connection
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Start engine.
Is it difficult to start engine?
YES >> GO TO 3.
NO
>> GO TO 4.
3.RESTART ENGINE
If it is difficult to start engine, the fuel injection system has a malfunction, too.
Crank engine while depressing accelerator pedal.
NOTE:
When depressing accelerator pedal three-fourths (3/4) or more, the control system does not start the
engine. Do not depress accelerator pedal too much.
Does engine start?
Revision: August 2014
EC-263
2015 Rogue NAM
P0171 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> Proceed to EC-264, "Diagnosis Procedure".
NO
>> Check exhaust and intake air leak visually.
4.PERFORM DTC CONFIRMATION PROCEDURE-2
1. Start engine and let it idle for at least 5 minutes.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-264, "Diagnosis Procedure".
NO
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE-3
1.
2.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine.
Maintain the following conditions for at least 10 consecutive minutes.
Hold the accelerator pedal as steady as possible.
VHCL SPEED SE
50 - 120 km/h (31 - 75 MPH)
CAUTION:
Always drive vehicle at a safe speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-264, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011277997
1.CHECK EXHAUST GAS LEAK
1.
2.
Start engine and run it at idle.
Listen for an exhaust gas leak before three way catalyst (manifold).
PBIB1216E
Is exhaust gas leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 2.
2.CHECK FOR INTAKE AIR LEAK
1. Listen for an intake air leak after the mass air flow sensor.
2. Check PCV hose connection.
Intake air leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 3.
3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect corresponding A/F sensor 1 harness connector.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
Revision: August 2014
EC-264
2015 Rogue NAM
P0171 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
A/F sensor 1
ECM
Connector
Terminal
Connector
F18
5.
Continuity
Terminal
F51
EC
41
Existed
45
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
A/F sensor 1
Connector
Continuity
Terminal
F18
Ground
Not existed
F
+
ECM
Connector
Continuity
Ground
Not existed
Terminal
41
F51
45
6. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK FUEL PRESSURE
Check fuel pressure. Refer to EC-147, "Work Procedure".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> GO TO 5.
5. DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging. Refer to EM-45, "Exploded View".
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly. Refer to FL-5, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
6.CHECK MASS AIR FLOW SENSOR
1.
2.
3.
With CONSULT
Install all removed parts.
Start engine and warm it up to normal operating temperature.
Check MASS AIR FLOW SENSOR (Hz) in DATA MONITOR mode of ENGINE using CONSULT.
Monitor item
Condition
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Revision: August 2014
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
EC-265
2015 Rogue NAM
P0171 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1.
2.
3.
Without CONSULT
Install all removed parts.
Start engine and warm it up to normal operating temperature.
Check mass air flow sensor signal in Service $01 with GST.
ECM
Connector
Condition
Terminal
Ignition switch ON (Engine stopped.)
F51
Value
35
34
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5000 - 5600 Hz
Idle to about 4,000 rpm
Ignition switch ON (Engine stopped.)
3500 - 4100 Hz to Approx. 6300 Hz*
Approx. 3500 Hz
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the measurement value within the specification?
YES >> GO TO 7.
NO
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
grounds. Refer to EC-205, "DTC Description".
7.CHECK FUNCTION OF FUEL INJECTOR
1.
2.
3.
With CONSULT
Start engine.
Perform POWER BALANCE in ACTIVE TEST mode of ENGINE using CONSULT.
Make sure that each circuit produces a momentary engine speed drop.
1.
2.
Without CONSULT
Let engine idle.
Listen to each fuel injector operating sound.
Clicking noise should be heard.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Perform trouble diagnosis for FUEL INJECTOR, refer
to EC-467, "Component Function Check".
PBIB3332E
8.CHECK FUEL INJECTOR
1.
2.
3.
4.
5.
6.
Turn ignition switch OFF.
Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
Disconnect all fuel injector harness connectors.
Remove fuel tube assembly. Refer to EM-45, "Removal and Installation".
Keep fuel hose and all fuel injectors connected to fuel tube.
Disconnect all ignition coil harness connectors.
Prepare pans or saucers under each fuel injector.
Revision: August 2014
EC-266
2015 Rogue NAM
P0171 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
7. Crank engine for about 3 seconds.
Fuel should be sprayed evenly for each fuel injector.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace fuel injectors from which fuel does not spray
out. Always replace O-ring with new ones. Refer to EM45, "Removal and Installation".
EC
C
PBIA9666J
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
E
>> INSPECTION END
F
Revision: August 2014
EC-267
2015 Rogue NAM
P0172 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0172 FUEL INJECTION SYSTEM FUNCTION
DTC Description
INFOID:0000000011277998
DTC DETECTION LOGIC
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual mixture ratio can be brought closely to the
theoretical mixture ratio based on the mixture ratio feedback signal from the A/F sensors 1. The ECM calculates the necessary compensation to correct the offset between the actual and the theoretical ratios.
In case the amount of the compensation value is extremely large (The actual mixture ratio is too rich.), the
ECM judges the condition as the fuel injection system malfunction and lights up the MIL (2 trip detection logic).
Sensor
Input signal to ECM
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
A/F sensor 1
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0172
FUEL SYS-RICH-B1
(System too rich bank 1)
ECM function
Fuel injection control
Actuator
Fuel injector
DTC detecting condition
Fuel injection system does not operate properly.
The amount of mixture ratio compensation is too large. (The mixture ratio
is too rich.)
POSSIBLE CAUSE
A/F sensor 1
Fuel injector
Exhaust gas leaks
Incorrect fuel pressure
Mass air flow sensor
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Start engine.
Is it difficult to start engine?
YES >> GO TO 3.
NO
>> GO TO 4.
3.RESTART ENGINE
If it is difficult to start engine, the fuel injection system has a malfunction, too.
Crank engine while depressing accelerator pedal.
NOTE:
When depressing accelerator pedal three-fourths (3/4) or more, the control system does not start the
engine. Do not depress accelerator pedal too much.
Does engine start?
YES >> Proceed to EC-269, "Diagnosis Procedure".
NO
>> Check exhaust and intake air leak visually.
Revision: August 2014
EC-268
2015 Rogue NAM
P0172 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4.PERFORM DTC CONFIRMATION PROCEDURE-2
1. Start engine and let it idle for at least 5 minutes.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-269, "Diagnosis Procedure".
NO
>> GO TO 5.
EC
5.PERFORM DTC CONFIRMATION PROCEDURE-3
1.
2.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine.
Maintain the following conditions for at least 10 consecutive minutes.
Hold the accelerator pedal as steady as possible.
VHCL SPEED SE
50 - 120 km/h (31 - 75 MPH)
CAUTION:
Always drive vehicle at a safe speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-269, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
G
INFOID:0000000011277999
1.CHECK EXHAUST GAS LEAK
1.
2.
Start engine and run it at idle.
Listen for an exhaust gas leak before three way catalyst (manifold).
PBIB1216E
Is exhaust gas leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 2.
2.CHECK FOR INTAKE AIR LEAK
1. Listen for an intake air leak after the mass air flow sensor.
2. Check PCV hose connection.
Intake air leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 3.
3.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect corresponding A/F sensor 1 harness connector.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
Revision: August 2014
EC-269
2015 Rogue NAM
P0172 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
A/F sensor 1
ECM
Connector
Terminal
1
F18
5.
Connector
Continuity
Terminal
41
F51
Existed
45
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
+
A/F sensor 1
Connector
Continuity
Ground
Not existed
Continuity
Ground
Not existed
Terminal
1
F18
+
ECM
Connector
F51
Terminal
41
45
6. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK FUEL PRESSURE
Check fuel pressure. Refer to EC-147, "Work Procedure".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> GO TO 5.
5. DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging. Refer to EM-45, "Exploded View".
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly. Refer to FL-5, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
6.CHECK MASS AIR FLOW SENSOR
1.
2.
3.
With CONSULT
Install all removed parts.
Start engine and warm it up to normal operating temperature.
Check MASS AIR FLOW SENSOR (Hz) in DATA MONITOR mode of ENGINE using CONSULT.
Monitor item
Condition
Value
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
Idle to about 4,000 rpm
3500- 4100 Hz
5000k - 5600 Hz
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Revision: August 2014
EC-270
2015 Rogue NAM
P0172 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1.
2.
3.
Without CONSULT
Install all removed parts.
Start engine and warm it up to normal operating temperature.
Check mass air flow sensor signal in Service $01 with GST.
EC
ECM
Connector
Condition
Terminal
Ignition switch ON (Engine stopped.)
Idle (Engine is warmed-up to normal operating temperature.)
F51
Value
35
34
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
Idle to about 4,000 rpm
Ignition switch ON (Engine stopped.)
Approx. 3500 Hz
3500- 4100 Hz
5000k - 5600 Hz
3500 - 4100 Hz to Approx. 6300 Hz*
Approx. 3500 Hz
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the measurement value within the specification?
YES >> GO TO 7.
NO
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
grounds. Refer to EC-201, "DTC Description".
7.CHECK FUNCTION OF FUEL INJECTOR
With CONSULT
1. Start engine.
2. Perform POWER BALANCE in ACTIVE TEST mode of ENGINE using CONSULT.
3. Make sure that each circuit produces a momentary engine speed drop.
1.
2.
Without CONSULT
Let engine idle.
Listen to each fuel injector operating sound.
Clicking noise should be heard.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Perform trouble diagnosis for FUEL INJECTOR, refer
to EC-467, "Component Function Check".
M
PBIB3332E
8.CHECK FUEL INJECTOR
1.
2.
3.
4.
5.
6.
Turn ignition switch OFF.
Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
Disconnect all fuel injector harness connectors.
Remove fuel tube assembly. Refer to EM-45, "Removal and Installation".
Keep fuel hose and all fuel injectors connected to fuel tube.
Disconnect all ignition coil harness connectors.
Prepare pans or saucers under each fuel injector.
Revision: August 2014
EC-271
2015 Rogue NAM
P0172 FUEL INJECTION SYSTEM FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
7. Crank engine for about 3 seconds.
Fuel should be sprayed evenly for each fuel injector.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace fuel injectors from which fuel does not spray
out. Always replace O-ring with new ones. Refer to EM45, "Removal and Installation".
PBIA9666J
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-272
2015 Rogue NAM
P0181 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0181 FTT SENSOR
DTC Description
INFOID:0000000011278000
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
FTT SENSOR
(Fuel temperature sensor A circuit range/
performance)
P0181
EC
DTC detecting condition
Rationally incorrect voltage from the sensor is sent to ECM, compared
with the voltage signals from ECT sensor and intake air temperature
sensor.
The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, EOT sensor, and FTT sensor) shows that the voltage signal of the FTT sensor is higher/lower
than that of other temperature sensors when the engine is started with
its cold state.
POSSIBLE CAUSE
DTC P0181 - A
Harness or connectors (FTT sensor circuit is open or shorted.)
FTT sensor
Combination meter
DTC P0181 - B
Harness or connectors (High or low resistance in the FTT sensor circuit)
FTT sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 7.
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-1
O
1. Turn ignition switch ON and wait at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-275, "Diagnosis Procedure".
NO
>> GO TO 4.
4.CHECK ENGINE COOLANT TEMPERATURE
1.
2.
With CONSULT
Select COOLAN TEMP/S in DATA MONITOR of ENGINE using CONSULT.
Check COOLAN TEMP/S value.
With GST
Revision: August 2014
EC-273
2015 Rogue NAM
P0181 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Follow the procedure With CONSULT above.
COOLAN TEMP/S less than 60C (140F)?
YES >> INSPECTION END
NO
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-2
With CONSULT
Cool engine down until COOLAN TEMP/S is less than 60C (140F).
Wait at least 10 seconds.
Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-275, "Diagnosis Procedure".
NO
>> GO TO 6.
1.
2.
3.
6.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Remove fuel level sensor unit. Refer to FL-5, "Removal and Installation".
Check resistance between fuel level sensor unit and fuel pump
terminals by heating with hot water as shown in the figure.
Fuel level sensor unit
and fuel pump
Condition
Resistance (k)
Terminal
3
Temperature [C
(F)]
20 (68)
2.3 2.7
50 (122)
0.79 0.90
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Proceed to EC-275, "Diagnosis Procedure".
JMBIA0167ZZ
7.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, do not add fuel.
Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 8.
8.PERFORM DTC CONFIRMATION PROCEDURE B
1.
2.
3.
Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between 10C (14F) and 35C (95F).
Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the hood open.
Start engine and let it idle for 5 minutes or more.
CAUTION:
Revision: August 2014
EC-274
2015 Rogue NAM
P0181 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-275, "Diagnosis Procedure".
NO
>> INSPECTION END
EC
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278001
1.INSPECTION START
Confirm the detected malfunction (A or B). Refer to EC-273, "DTC Description".
Which malfunction is detected?
A
>> GO TO 2.
B
>> GO TO 6.
2.CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Proceed to MWI-63, "Component Function Check".
1.
2.
3.
4.
3.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Turn ignition switch ON.
Check the voltage between fuel level sensor unit and fuel pump harness connector and ground.
Voltage
(Approx.)
Ground
5V
Fuel level sensor unit and fuel pump
Connector
Terminal
B103
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness
connector.
+
Fuel level sensor unit and
fuel pump
ECM
O
Continuity
Connector
Terminal
Connector
Terminal
B103
E16
125
P
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-275
2015 Rogue NAM
P0181 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
5.CHECK FTT SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness
connector.
+
Fuel level sensor unit and
fuel pump
ECM
Continuity
Connector
Terminal
Connector
Terminal
B103
E16
124
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
Check the FTT sensor. Refer to EC-276, "Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
Component Inspection
INFOID:0000000011278002
1.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Remove fuel level sensor unit. Refer to FL-5, "Removal and Installation".
Check resistance between fuel level sensor unit and fuel pump
terminals by heating with hot water as shown in the figure.
Fuel level sensor unit
and fuel pump
Condition
Resistance (k)
Terminal
3
Temperature
[C (F)]
20 (68)
2.3 2.7
50 (122)
0.79 0.90
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
Revision: August 2014
EC-276
JMBIA0167ZZ
2015 Rogue NAM
P0182, P0183 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0182, P0183 FTT SENSOR
DTC Description
INFOID:0000000011278003
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0182
FTT SEN/CIRCUIT
(Fuel temperature sensor A circuit low)
An excessively low voltage from the sensor is sent to ECM.
P0183
FTT SEN/CIRCUIT
(Fuel temperature sensor A circuit high)
An excessively high voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (The FTT sensor circuit is open or shorted.)
Fuel tank temperature sensor
Combination meter
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-277, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
L
INFOID:0000000011278004
1.CHECK DTC WITH COMBINATION METER
Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Proceed to MWI-63, "Component Function Check".
2.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Turn ignition switch ON.
Check the voltage between fuel level sensor unit and fuel pump harness connector and ground.
Revision: August 2014
EC-277
2015 Rogue NAM
P0182, P0183 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Fuel level sensor unit and fuel
pump
Connector
Terminal
B103
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness
connector.
+
Fuel level sensor unit and
fuel pump
ECM
Continuity
Connector
Terminal
Connector
Terminal
B103
E16
125
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM connector.
Check the continuity between fuel level sensor unit and fuel pump harness connector and ECM harness
connector.
+
Fuel level sensor unit and
fuel pump
ECM
Continuity
Connector
Terminal
Connector
Terminal
B103
E16
124
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
Check the FTT sensor. Refer to EC-279, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
6.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-278
2015 Rogue NAM
P0182, P0183 FTT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Component Inspection
INFOID:0000000011278005
1.CHECK FUEL TANK TEMPERATURE (FTT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Remove fuel level sensor unit. Refer to FL-5, "Removal and Installation".
Check resistance between fuel level sensor unit and fuel pump
terminals by heating with hot water as shown in the figure.
EC
Fuel level sensor unit
and fuel pump
Condition
Resistance (k)
Terminal
3
Temperature
[C (F)]
20 (68)
2.3 2.7
50 (122)
0.79 0.90
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
JMBIA0167ZZ
Revision: August 2014
EC-279
2015 Rogue NAM
P0196 EOT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0196 EOT SENSOR
DTC Description
INFOID:0000000011278006
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0196
EOT SENSOR
(Engine oil temperature sensor range/performance)
DTC detecting condition
Rationally incorrect voltage from the sensor is sent to ECM, compared
with the voltage signals from EOT sensor and intake air temperature
sensor.
The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the signal voltage of the EOT sensor is higher/lower
than that of other temperature sensors when the engine is started with
its cold state.
POSSIBLE CAUSE
DTC P0196 - A
Harness or connectors (EOT sensor circuit is open or shorted.)
EOT sensor
DTC P0196 - B
Harness or connectors (High or low resistance in the EOT sensor circuit)
EOT sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0196 is displayed with DTC P0197 or P0198, first perform the trouble diagnosis for DTC P0197 or
P0198.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.INSPECTION START
Is it necessary to erase permanent DTC?
YES >> GO TO 7.
NO
>> GO TO 3.
3.PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-1
1.
2.
3.
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Revision: August 2014
EC-280
2015 Rogue NAM
P0196 EOT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and let it idle for 5 minutes and 10 seconds.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-282, "Diagnosis Procedure".
NO
>> GO TO 5.
[QR25DE]
A
EC
5.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-2
With CONSULT
1. Select DATA MONITOR mode of ENGINE using CONSULT.
2. Check that COOLAN TEMP/S indicates above 80C (176F).
If it is above 80C (176F), go to the following steps.
If it is below 80C (176F), warm engine up until COOLAN TEMP/S indicates more than 80C (176F).
Then perform the following steps.
3. Turn ignition switch OFF and soak the vehicle in a cool place.
4. Turn ignition switch ON.
NOTE:
Do not turn ignition switch OFF until step 8.
5. Select DATA MONITOR mode of ENGINE using CONSULT.
6. Check the following.
COOLAN TEMP/S
Below 40C (104F)
INT/A TEMP SE
Below 40C (104F)
Difference between COOLAN TEMP/S and INT/A TEMP SE
Within 6C (11F)
If they are within the specified range, perform the following steps.
If they are out of the specified range, soak the vehicle to meet the above conditions. Then perform the following steps.
NOTE:
Do not turn ignition switch OFF.
If it is supposed to need a long period of time, do not deplete the battery.
7. Start engine and let it idle for 5 minutes.
8. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-282, "Diagnosis Procedure".
NO
>> GO TO 6.
6.CHECK ENGINE OIL TEMPERATURE (EOT) SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect EOT sensor harness connector.
Remove EOT sensor. Refer to EC-14, "Component Parts Location".
Check resistance between EOT sensor terminals by heating
with hot water as shown in the figure.
EOT sensor
Condition
Resistance (k)
Terminal
Temperature [C
(F)]
20 (68)
2.37 2.63
50 (122)
0.68 1.00
90 (194)
0.236 0.260
P
JMBIA0080ZZ
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Proceed to EC-282, "Diagnosis Procedure".
7.PRECONDITIONING
Revision: August 2014
EC-281
2015 Rogue NAM
P0196 EOT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, do not add fuel.
Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 8.
8.PERFORM DTC CONFIRMATION PROCEDURE B
1.
Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between 10C (14F) and 35C (95F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the hood open.
3. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-282, "Diagnosis Procedure".
NO
>> INSPECTION END
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278007
1.CHECK DTC PRIORITY
If DTC P0196 is displayed with DTC P0197 or P0198, first perform the trouble diagnosis for DTC P0197 or
P0198.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK ENGINE OIL TEMPERATURE (EOT) SENSOR
Check EOT sensor. Refer to EC-282, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace EOT sensor. Refer to EC-14, "Component Parts Location".
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278008
1.CHECK ENGINE OIL TEMPERATURE SENSOR
Revision: August 2014
EC-282
2015 Rogue NAM
P0196 EOT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect engine oil temperature sensor harness connector.
3. Remove engine oil temperature sensor.
4. Check resistance between engine oil temperature sensor terminals by heating with hot water as shown in the figure.
[QR25DE]
A
EC
Engine oil temperature
sensor
Resistance (k)
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
Condition
Terminal
Temperature
[C (F)]
JMBIA0080ZZ
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine oil temperature sensor. Refer to EC-14, "Component Parts Location".
Revision: August 2014
EC-283
2015 Rogue NAM
P0197, P0198 EOT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0197, P0198 EOT SENSOR
DTC Description
INFOID:0000000011278009
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0197
EOT SEN/CIRC
(Engine oil temperature sensor low)
An excessively low voltage from the engine oil temperature sensor is sent
to ECM.
P0198
EOT SEN/CIRC
(Engine oil temperature sensor high)
An excessively high voltage from the engine oil temperature sensor is sent
to ECM.
POSSIBLE CAUSE
Harness or connectors (EOT sensor circuit is open or shorted.)
Engine oil temperature sensor
FAIL-SAFE
Exhaust valve timing control does not function.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-284, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278010
1.CHECK ENGINE OIL TEMPERATURE SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect engine oil temperature (EOT) sensor harness connector.
Turn ignition switch ON.
Check the voltage between EOT sensor harness connector and ground.
+
EOT sensor
Connector
Terminal
F68
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK ENGINE OIL TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
1.
2.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Revision: August 2014
EC-284
2015 Rogue NAM
P0197, P0198 EOT SENSOR
< DTC/CIRCUIT DIAGNOSIS >
3. Check the continuity between EOT sensor harness connector and ECM harness connector.
[QR25DE]
A
EOT sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F68
F51
25
EC
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK EOT SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EOT sensor harness connector and ECM harness connector.
EOT sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F68
F51
26
G
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK ENGINE OIL TEMPERATURE SENSOR
Check the engine oil temperature sensor. Refer to EC-282, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace engine oil temperature sensor. Refer to EC-14, "Component Parts Location".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
L
>> INSPECTION END
Component Inspection
INFOID:0000000011278011
1.CHECK ENGINE OIL TEMPERATURE SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect engine oil temperature sensor harness connector.
Remove engine oil temperature sensor.
Check resistance between engine oil temperature sensor terminals by heating with hot water as shown in the figure.
Engine oil temperature
sensor
Condition
Resistance (k)
Terminal
Revision: August 2014
Temperature
[C (F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
EC-285
JMBIA0080ZZ
2015 Rogue NAM
P0197, P0198 EOT SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace engine oil temperature sensor. Refer to EC-14, "Component Parts Location".
Revision: August 2014
EC-286
2015 Rogue NAM
P0222, P0223 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0222, P0223 TP SENSOR
DTC Description
INFOID:0000000011278012
DTC DETECTION LOGIC
DTC No.
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0222
TP SEN 1/CIRC-B1
(Throttle/pedal position sensor/switch B
circuit low)
An excessively low voltage from the TP sensor 1 is sent to ECM.
P0223
TP SEN 1/CIRC-B1
(Throttle/pedal position sensor/switch B
circuit high)
An excessively high voltage from the TP sensor 1 is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (TP sensor 1 circuit is open or shorted.)
Electric throttle control actuator (TP sensor 1)
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
If DTC P0222 or P0223 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
1.CHECK DTC PRIORITY
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
N
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-287, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278013
1.CHECK DTC PRIORITY
If DTC P0222 or P0223 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
Revision: August 2014
EC-287
2015 Rogue NAM
P0222, P0223 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Turn ignition switch ON.
Check the voltage between electric throttle control actuator harness connector and ground.
+
Voltage
(Approx.)
Ground
5V
Electric throttle control actuator
Connector
Terminal
F50
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
80
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK THROTTLE POSITION SENSOR 1 GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
78
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK THROTTLE POSITION SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
Revision: August 2014
EC-288
2015 Rogue NAM
P0222, P0223 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Electric throttle control actuator
ECM
A
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
79
EC
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK THROTTLE POSITION SENSOR
Check the throttle position sensor. Refer to EC-289, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
G
>> INSPECTION END
Component Inspection
INFOID:0000000011278014
1.CHECK THROTTLE POSITION SENSOR
1.
2.
3.
4.
5.
6.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
Turn ignition switch ON.
Set selector lever to D position.
Check the voltage between ECM harness connector terminals as per the following conditions.
Sensor 1
Condition
Voltage
Terminal
79
F52
Sensor 2
ECM
Connector
78
77
Accelerator
pedal
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-289
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0300, P0301, P0302, P0303, P0304 MISFIRE
DTC Description
INFOID:0000000011278015
DTC DETECTION LOGIC
When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor (POS) signal to vary, ECM can determine that a misfire is occurring.
Sensor
Crankshaft position sensor (POS)
Input signal to ECM
Engine speed
ECM function
On board diagnosis of misfire
The misfire detection logic consists of the following two conditions.
1. One Trip Detection Logic (Three Way Catalyst Damage)
On the 1st trip, when a misfire condition occurs that can damage the three way catalyst (TWC) due to
overheating, the MIL will blink.
When a misfire condition occurs, the ECM monitors the CKP sensor signal every 200 engine revolutions
for a change.
When the misfire condition decreases to a level that will not damage the TWC, the MIL will turn off.
If another misfire condition occurs that can damage the TWC on a second trip, the MIL will blink.
When the misfire condition decreases to a level that will not damage the TWC, the MIL will remain on.
If another misfire condition occurs that can damage the TWC, the MIL will begin to blink again.
2. Two Trip Detection Logic (Exhaust quality deterioration)
For misfire conditions that will not damage the TWC (but will affect vehicle emissions), the MIL will only
light when the misfire is detected on a second trip. During this condition, the ECM monitors the CKP sensor signal every 1,000 engine revolutions.
A misfire malfunction can be detected on any one cylinder or on multiple cylinders.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0300
MULTI CYL MISFIRE
(Random/multiple cylinder misfire detected)
Multiple cylinder misfire.
P0301
CYL 1 MISFIRE
(Cylinder 1 Misfire Detected)
No. 1 cylinder misfires.
P0302
CYL 2 MISFIRE
(Cylinder 2 Misfire Detected)
No. 2 cylinder misfires.
P0303
CYL 3 MISFIRE
(Cylinder 3 Misfire Detected)
No. 3 cylinder misfires.
P0304
CYL 4 MISFIRE
(Cylinder 4 Misfire Detected)
No. 4 cylinder misfires.
POSSIBLE CAUSE
Improper spark plug
Insufficient compression
Incorrect fuel pressure
Fuel Injector circuit is open or shorted
Fuel injector
Intake air leak
Ignition signal circuit is open or shorted
Lack of fuel
Signal plate
A/F sensor 1
Incorrect PCV hose connection
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
Revision: August 2014
EC-290
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
EC
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Restart engine and let it idle for about 15 minutes.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-291, "Diagnosis Procedure".
NO
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
1.
2.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and drive the vehicle as per the similar conditions to (1st trip) Freeze Frame Data for a certain
time. Refer to the table below.
Hold the accelerator pedal as steady as possible.
The similar conditions to (1st trip) Freeze Frame Data means the vehicle operation that the following conditions should be satisfied at the same time.
CAUTION:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws when
driving.
Engine speed
Engine speed in the freeze frame data 400 rpm
Vehicle speed
Vehicle speed in the freeze frame data 10 km/h (6 MPH)
Engine coolant temperature (T)
condition
When the freeze frame data shows lower than 70C (158F),
T should be lower than 70C (158F).
When the freeze frame data shows higher than or equal to 70C (158F),
T should be higher than or equal to 70C (158F).
The time to driving varies according to the engine speed in the freeze frame data.
Engine speed
Time
Around 1,000 rpm
Approximately 10 minutes
Around 2,000 rpm
Approximately 5 minutes
More than 3,000 rpm
Approximately 3.5 minutes
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-291, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278016
1.CHECK FOR INTAKE AIR LEAK AND PCV HOSE
1. Start engine and run it at idle speed.
2. Listen for the sound of the intake air leak.
3. Check PCV hose connection.
Is intake air leak detected?
YES >> Discover air leak location and repair.
NO
>> GO TO 2.
Revision: August 2014
EC-291
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK FOR EXHAUST SYSTEM CLOGGING
Stop engine and visually check exhaust tube, three way catalyst and muffler for dents.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 3.
YES-2 >> Without CONSULT: GO TO 4.
NO
>> Repair or replace it.
3.PERFORM POWER BALANCE TEST
With CONSULT
1. Start engine.
2. Perform POWER BALANCE in ACTIVE TEST mode of ENGINE using CONSULT.
3. Make sure that each circuit produces a momentary engine speed drop.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> GO TO 4.
4.CHECK FUNCTION OF FUEL INJECTOR
1.
2.
Start engine and let engine idle.
Listen to each fuel injector operating sound.
Clicking noise should be heard.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Perform trouble diagnosis for FUEL INJECTOR. Refer
to EC-467, "Diagnosis Procedure".
PBIB3332E
5.CHECK FUNCTION OF IGNITION COIL-1
CAUTION:
Do the following procedure in the place where ventilation is good without the combustible.
1. Turn ignition switch OFF.
2. Remove fuel pump fuse in IPDM E/R to release fuel pressure.
NOTE:
Do not use CONSULT to release fuel pressure, or fuel pressure applies again during the following procedure.
3. Start engine.
4. After engine stalls, crank it two or three times to release all fuel pressure.
5. Turn ignition switch OFF.
6. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.
7. Remove ignition coil and spark plug of the cylinder to be checked.
8. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
9. Connect spark plug and harness connector to ignition coil.
10. Fix ignition coil using a rope etc. with gap of 13 - 17 mm (0.52 0.66 in) between the edge of the spark plug and grounded metal
portion as shown in the figure.
11. Crank engine for about 3 seconds, and check whether spark is
generated between the spark plug and the grounded metal portion.
Spark should be generated.
CAUTION:
Do not approach to the spark plug and the ignition coil
within 50 cm (19.7 in). Be careful not to get an electrical
shock while checking, because the electrical discharge
voltage becomes 20 kV or more.
Revision: August 2014
EC-292
JMBIA0066GB
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
It might cause to damage the ignition coil if the gap of more than 17 mm (0.66 in) is taken.
NOTE:
A
When the gap is less than 13 mm (0.52 in), the spark might be generated even if the coil is malfunctioning.
Is the inspection result normal?
EC
YES >> GO TO 9.
NO
>> GO TO 6.
6.CHECK FUNCTION OF IGNITION COIL-2
1.
2.
3.
Turn ignition switch OFF.
Disconnect spark plug and connect a known-good spark plug.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded metal portion.
Spark should be generated.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Check ignition coil, power transistor and their circuits. Refer to EC-473, "Diagnosis Procedure".
7.CHECK SPARK PLUG
Check the initial spark plug for fouling, etc.
Is the inspection result normal?
YES >> Replace spark plug(s) with standard type one(s). For
spark plug type, refer to EM-120, "Spark Plug".
NO
>> Repair or clean spark plug. Then GO TO 8.
SEF156I
8.CHECK FUNCTION OF IGNITION COIL-3
1.
2.
Reconnect the initial spark plugs.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded portion.
Spark should be generated.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace spark plug(s) with standard type one(s). For spark plug type. Refer to EM-120,
"Spark Plug".
9.CHECK COMPRESSION PRESSURE
Check compression pressure. Refer to EM-24, "Compression pressure".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Check pistons, piston rings, valves, valve seats and cylinder head gaskets.
10.CHECK FUEL PRESSURE
1.
2.
3.
Install all removed parts.
Release fuel pressure to zero.
Install fuel pressure gauge and check fuel pressure. Refer to EC-147, "Work Procedure".
At idling: Approximately 350 kPa (3.57 kg/cm2, 51 psi)
Is the inspection result normal?
YES >> GO TO 12.
Revision: August 2014
EC-293
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> GO TO 11.
11.DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly. Refer to FL-5, "Removal and Installation".
NO
>> Repair or replace.
12.CHECK IGNITION TIMING
Check the following items.
For procedure, refer to EC-135, "Work Procedure".
For specification, refer to EC-503, "Ignition Timing".
Is the inspection result normal?
YES >> GO TO 13.
NO
>> Follow the EC-135, "Work Procedure".
13.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Continuity
Connector
Terminal
Connector
Terminal
F18
F51
41
Existed
Check the continuity between A/F sensor 1 harness connector or ECM harness connector and ground.
+
A/F sensor 1
Connector
Terminal
F18
Continuity
Ground
Not existed
Continuity
Ground
Not existed
+
ECM
Connector
Terminal
F51
41
6. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 14.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
14.CHECK A/F SENSOR 1 HEATER
Check the A/F sensor 1 heater. Refer to EC-189, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 15.
NO
>> Replace A/F sensor 1. Refer to EM-32, "Exploded View".
15.CHECK MASS AIR FLOW SENSOR
1.
2.
3.
With CONSULT
Install all removed parts.
Start engine and warm it up to normal operating temperature.
Check MASS AIR FLOW SENSOR (Hz) in DATA MONITOR mode of ENGINE using CONSULT.
Revision: August 2014
EC-294
2015 Rogue NAM
P0300, P0301, P0302, P0303, P0304 MISFIRE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Monitor item
Condition
Ignition switch ON (Engine stopped.)
MASS AIR
FLOW SENSOR
(Hz)
Value
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5100 - 5600 Hz
Idle to about 4,000 rpm
EC
3500 - 4100 Hz to Approx. 6300 Hz*
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Without CONSULT
1. Install all removed parts.
2. Start engine and warm it up to normal operating temperature.
3. Check mass air flow sensor signal in Service $01 with GST.
ECM
Connector
Condition
Terminal
Ignition switch ON (Engine stopped.)
F51
Value
35
34
Approx. 3500 Hz
Idle (Engine is warmed-up to normal operating temperature.)
3500- 4100 Hz
2,500 rpm (Engine is warmed-up to normal operating
temperature.)
5100 - 5600 Hz
Idle to about 4,000 rpm
Ignition switch ON (Engine stopped.)
3500 - 4100 Hz to Approx. 6300 Hz*
Approx. 3500 Hz
*: Check for linear frequency rise in response to engine being increased to about 4,000 rpm.
Is the measurement value within the specification?
YES >> GO TO 16.
NO
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
ground. Refer to EC-205, "DTC Description".
16.CHECK SYMPTOM TABLE
Check items on the rough idle symptom in EC-489, "Symptom Table".
Is the inspection result normal?
YES >> GO TO 17.
NO
>> Repair or replace error-detected parts.
17.ERASE THE 1ST TRIP DTC
Some tests may cause a 1st trip DTC to be set.
Erase the 1st trip DTC from the ECM memory after performing the tests. Refer to EC-58, "Diagnosis Description".
>> GO TO 18.
18.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
P
>> INSPECTION END
Revision: August 2014
EC-295
2015 Rogue NAM
P0327, P0328 KS
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0327, P0328 KS
DTC Description
INFOID:0000000011278017
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0327
KNOCK SEN/CIRC-B1
(Knock sensor 1 circuit low bank 1 or single
sensor)
An excessively low voltage from the knock sensor is sent to ECM.
P0328
KNOCK SEN/CIRC-B1
(Knock sensor 1 circuit high bank 1 or single
sensor)
An excessively high voltage from the knock sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (Knock sensor circuit is open or shorted.)
Knock sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and run it for at least 5 seconds at idle speed.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-296, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278018
1.CHECK KNOCK SENSOR GROUND CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect knock sensor harness connector.
Disconnect ECM harness connector.
Check the continuity between knock sensor harness connector and ECM harness connector.
+
Knock sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F9
F51
Existed
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 2.
Revision: August 2014
EC-296
2015 Rogue NAM
P0327, P0328 KS
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> Repair or replace error-detected parts.
2.CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between knock sensor harness connector and ECM harness connector.
+
Knock sensor
ECM
EC
Continuity
Connector
Terminal
Connector
Terminal
F9
F51
C
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK KNOCK SENSOR
Check the knock sensor. Refer to EC-297, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Replace knock sensor. Refer to EM-97, "Exploded View".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
H
>> INSPECTION END
Component Inspection
INFOID:0000000011278019
1.CHECK KNOCK SENSOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect knock sensor harness connector.
Check resistance between knock sensor terminals as per the following.
NOTE:
It is necessary to use an ohmmeter which can measure more than 10 M.
Knock sensor
+
Resistance
Approx. 532 - 588 k [at 20C (68F)]
Terminals
1
CAUTION:
Do not use any knock sensors that have been dropped or physically damaged. Use only new ones.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace knock sensor. Refer to EM-97, "Exploded View".
Revision: August 2014
EC-297
2015 Rogue NAM
P0335 CKP SENSOR (POS)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0335 CKP SENSOR (POS)
DTC Description
INFOID:0000000011278020
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0335
CKP SEN/CIRCUIT
(Crankshaft position sensor A circuit)
DTC detecting condition
The crankshaft position sensor (POS) signal is not detected by the ECM
during the first few seconds of engine cranking.
The proper pulse signal from the crankshaft position sensor (POS) is not
sent to ECM while the engine is running.
The crankshaft position sensor (POS) signal is not in the normal pattern
during engine running.
POSSIBLE CAUSE
Harness or connectors [Crankshaft position sensor (POS) circuit is open or shorted.]
Crankshaft position sensor (POS)
Signal plate
Sensor power supply 2 circuit
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0335 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V with ignition switch ON.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-298, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278021
1.CHECK DTC PRIORITY
If DTC P0335 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
Revision: August 2014
EC-298
2015 Rogue NAM
P0335 CKP SENSOR (POS)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY
1.
2.
3.
Disconnect crankshaft position (CKP) sensor (POS) harness connector.
Turn ignition switch ON.
Check the voltage between CKP sensor (POS) harness connector and ground.
EC
Voltage
(Approx.)
Ground
5V
CKP sensor (POS)
Connector
Terminal
F17
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK CKP SENSOR (POS) GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
+
CKP sensor (POS)
ECM
G
Continuity
Connector
Terminal
Connector
Terminal
F17
F52
70
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT
1.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
+
CKP sensor (POS)
ECM
K
Continuity
Connector
Terminal
Connector
Terminal
F17
F52
71
L
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK CRANKSHAFT POSITION SENSOR (POS)
Check the crankshaft position sensor (POS). Refer to EC-300, "Component Inspection (Crankshaft Position
sensor)".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
6.CHECK GEAR TOOTH
1.
Remove crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
Revision: August 2014
EC-299
2015 Rogue NAM
P0335 CKP SENSOR (POS)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Look into the mounting hole of the crankshaft position sensor
(POS) to check that there is no missing gear tooth in the signal
plate .
JPBIA4623ZZ
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace the signal plate. Refer to EM-97, "Exploded View".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection (Crankshaft Position sensor)
INFOID:0000000011278022
1.CHECK CRANKSHAFT POSITION SENSOR (POS)-1
1. Turn ignition switch OFF.
2. Loosen the fixing bolt of the sensor.
3. Disconnect crankshaft position sensor (POS) harness connector.
4. Remove the sensor.
5. Visually check the sensor for chipping.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace crankshaft position sensor (POS). Refer to EM97, "Exploded View".
PBIA9209J
2.CHECK CRANKSHAFT POSITION SENSOR (POS)-2
Check the resistance between crankshaft position sensor (POS) terminals as per the following.
Crankshaft position sensor (POS)
Resistance [at 25C (77F)]
Terminal (Polarity)
1
2
2
3
Except 0 or
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
Revision: August 2014
EC-300
2015 Rogue NAM
P0340 CMP SENSOR (PHASE)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0340 CMP SENSOR (PHASE)
DTC Description
INFOID:0000000011278023
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
CMP SEN/CIRC-B1
(Camshaft position sensor A circuit bank
1 or single sensor)
The cylinder No. signal is not sent to ECM for the first few seconds during
engine cranking.
The cylinder No. signal is not sent to ECM during engine running.
The cylinder No. signal is not in the normal pattern during engine running.
DTC No.
P0340
EC
POSSIBLE CAUSE
Harness or connectors (Camshaft position sensor circuit is open or shorted.)
Camshaft position sensor
Camshaft (Intake)
Starter motor
Starting system circuit
Dead (Weak) battery
Sensor power supply 2 circuit
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V with ignition switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-301, "Diagnosis Procedure".
NO
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
1. Maintaining engine speed at more than 800 rpm for at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-301, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
P
INFOID:0000000011278024
1.CHECK STARTING SYSTEM
Turn ignition switch to START position.
Does the engine turn over? Does the starter motor operate?
Revision: August 2014
EC-301
2015 Rogue NAM
P0340 CMP SENSOR (PHASE)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO
>> Check starting system (Refer to STR-11, "Work Flow (With GR8-1200 NI)" or STR-15, "Work Flow
(Without GR8-1200 NI)").
2.CHECK CAMSHAFT POSITION (CMP) SENSOR (PHASE) POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect camshaft position (CMP) sensor (PHASE) harness connector.
Turn ignition switch ON.
Check the voltage between CMP sensor (PHASE) harness connector and ground.
+
Voltage
(Approx.)
Ground
5V
CMP sensor (PHASE)
Connector
Terminal
F44
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Is inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK CMP SENSOR (PHASE) GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between CMP sensor (PHASE) harness connector and ECM harness connector.
+
CMP sensor (PHASE)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F44
F51
30
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK CMP SENSOR (PHASE) INPUT SIGNAL CIRCUIT
1.
2.
Disconnect ECM harness connector.
Check the continuity between CMP sensor (PHASE) harness connector and ECM harness connector.
+
CMP sensor (PHASE)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F44
F51
31
Existed
3. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK CAMSHAFT POSITION SENSOR (PHASE)
Check the camshaft position sensor (PHASE). Refer to EC-303, "Component Inspection (Camshaft position
sensor)".
Revision: August 2014
EC-302
2015 Rogue NAM
P0340 CMP SENSOR (PHASE)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace camshaft position sensor (PHASE). Refer to EM-69, "Removal and Installation".
7.CHECK CAMSHAFT (INT)
EC
Check the following.
Accumulation of debris to the signal plate of camshaft rear end
Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to EM-69, "Removal
and Installation".
E
JPBIA5855ZZ
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
G
>> INSPECTION END
Component Inspection (Camshaft position sensor)
INFOID:0000000011278025
1.CHECK CAMSHAFT POSITION SENSOR (PHASE)-1
1. Turn ignition switch OFF.
2. Loosen the fixing bolt of the sensor.
3. Disconnect camshaft position sensor (PHASE) harness connector.
4. Remove the sensor.
5. Visually check the sensor for chipping.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace camshaft position sensor (PHASE).
2.CHECK CAMSHAFT POSITION SENSOR (PHASE)-2
PBIA9876J
Check the resistance camshaft position sensor (PHASE) terminals as per the following.
N
Camshaft position sensor (PHASE)
Resistance [ at 25C (77F)]
Terminals (Polarity)
1
2
2
3
Except 0 or
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace camshaft position sensor (PHASE). Refer to EM-69, "Removal and Installation".
Revision: August 2014
EC-303
2015 Rogue NAM
P0420 THREE WAY CATALYST FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0420 THREE WAY CATALYST FUNCTION
DTC Description
INFOID:0000000011278026
DTC DETECTION LOGIC
The ECM monitors the switching frequency ratio of air fuel ratio (A/F)
sensor 1 and heated oxygen sensor 2.
A three way catalyst (manifold) with high oxygen storage capacity
will indicate a low switching frequency of heated oxygen sensor 2.
As oxygen storage capacity decreases, the heated oxygen sensor 2
switching frequency will increase.
When the frequency ratio of air fuel ratio (A/F) sensor 1 and heated
oxygen sensor 2 approaches a specified limit value, the three way
catalyst (manifold) malfunction is diagnosed.
SEF484YB
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
TW CATALYST SYS-B1
(Catalyst system efficiency below threshold
bank 1)
Three way catalyst (manifold) does not operate properly.
Three way catalyst (manifold) does not have enough oxygen storage capacity.
DTC No.
P0420
POSSIBLE CAUSE
Three way catalyst (manifold)
Exhaust tube
Intake air leaks
Fuel injector
Fuel injector leaks
Spark plug
Improper ignition timing
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Will CONSULT be used?
YES >> GO TO 2.
NO
>> GO TO 6.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
TESTING CONDITION:
Do not hold engine speed for more than the specified minutes below.
1. Start engine and warm it up to the normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
6. Let engine idle for 1 minute.
7. Select DATA MONITOR mode of ENGINE using CONSULT.
8. Check that COOLAN TEMP/S indicates more than 70C (158F).
Revision: August 2014
EC-304
2015 Rogue NAM
P0420 THREE WAY CATALYST FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
If not, warm up engine and go to next step when COOLAN TEMP/S indication reaches to 70C (158F).
9. Open engine hood.
A
10. Select DTC & SRT CONFIRMATION then SRT WORK SUPPORT mode of ENGINE using CONSULT.
11. Rev engine up to 2,500 to 3,000 rpm and hold it for 3 consecutive minutes then release the accelerator
EC
pedal completely.
12. Check the indication of CATALYST.
Which is displayed on CONSULT screen?
C
CMPLT >> GO TO 5.
INCMP >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
1.
2.
Wait 5 seconds at idle.
Rev engine up to 2,500 to 3,000 rpm and maintain it until INCMP of CATALYST changes to CMPLT (It
will take approximately 5 minutes).
Does the indication change to CMPLT?
YES >> GO TO 5.
NO
>> GO TO 4.
1.
2.
4.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Stop engine and cool it down to less than 70C (158F).
Perform DTC confirmation procedure again.
>> GO TO 2.
5.PERFORM DTC CONFIRMATION PROCEDURE-3
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-305, "Diagnosis Procedure".
NO
>> INSPECTION END
6.PERFORM COMPONENT FUNCTION CHECK
Without CONSULT
Start engine and warm it up to the normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Restart engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no
load.
4. Let engine idle for 1 minute.
5. Open engine hood.
6. Check the voltage between ECM harness connector terminals as per the following condition.
1.
2.
3.
M
ECM
Connector
F51
Condition
Voltage (V)
Terminal
22
23
Keeping engine speed at 2500 rpm
constant under no load
The voltage fluctuation cycle takes more
than 5 seconds.
1 cycle: 0.6 - 1.0 0 - 0.3 0.6 - 1.0
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-305, "Diagnosis Procedure".
Diagnosis Procedure
P
INFOID:0000000011278027
1.CHECK EXHAUST SYSTEM
Visually check exhaust tubes and muffler for dent.
Is the inspection result normal?
Revision: August 2014
EC-305
2015 Rogue NAM
P0420 THREE WAY CATALYST FUNCTION
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
[QR25DE]
2.CHECK EXHAUST GAS LEAK
1.
2.
Start engine and run it at idle.
Listen for an exhaust gas leak before the three way catalyst (manifold).
PBIB1216E
Is exhaust gas leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 3.
3.CHECK INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES >> Repair or replace error-detected parts.
NO
>> GO TO 4.
4.CHECK IGNITION TIMING AND IDLE SPEED
Check the following items. Refer to EC-135, "Work Procedure".
For specification, refer to EC-503, "Ignition Timing"
For specification, refer to EC-503, "Idle Speed".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Follow the EC-135, "Work Procedure".
5.CHECK FUEL INJECTOR
Check the fuel injector. Refer to EC-467, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Perform EC-467, "Diagnosis Procedure".
6.CHECK FUNCTION OF IGNITION COIL-1
CAUTION:
Do the following procedure in the place where ventilation is good without the combustible.
1. Turn ignition switch OFF.
2. Remove fuel pump fuse in IPDM E/R to release fuel pressure.
NOTE:
Do not use CONSULT to release fuel pressure, or fuel pressure applies again during the following procedure.
3. Start engine.
4. After engine stalls, crank it two or three times to release all fuel pressure.
5. Turn ignition switch OFF.
6. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.
7. Remove ignition coil and spark plug of the cylinder to be checked.
8. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
9. Connect spark plug and harness connector to ignition coil.
Revision: August 2014
EC-306
2015 Rogue NAM
P0420 THREE WAY CATALYST FUNCTION
< DTC/CIRCUIT DIAGNOSIS >
10. Fix ignition coil using a rope etc. with gap of 13 - 17 mm (0.52 0.66 in) between the edge of the spark plug and grounded metal
portion as shown in the figure.
11. Crank engine for about 3 seconds, and check whether spark is
generated between the spark plug and the grounded metal portion.
[QR25DE]
A
EC
Spark should be generated.
CAUTION:
Do not approach to the spark plug and the ignition coil
JMBIA0066GB
within 50 cm (19.7 in). Be careful not to get an electrical
shock while checking, because the electrical discharge
voltage becomes 20 kV or more.
It might cause to damage the ignition coil if the gap of more than 17 mm (0.66 in) is taken.
NOTE:
When the gap is less than 13 mm (0.52 in), the spark might be generated even if the coil is malfunctioning.
Is the inspection result normal?
YES >> GO TO 10.
NO
>> GO TO 7.
7.CHECK FUNCTION OF IGNITION COIL-2
1.
2.
3.
Turn ignition switch OFF.
Disconnect spark plug and connect a known-good spark plug.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded metal portion.
Spark should be generated.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Check ignition coil, power transistor and their circuits. Refer to EC-473, "Diagnosis Procedure".
8.CHECK SPARK PLUG
Check the initial spark plug for fouling, etc. Refer to EM-19,
"Removal and Installation".
Is the inspection result normal?
YES >> Replace spark plug(s) with standard type one(s). For
spark
plug
type,
refer
to
EM-120,
"General Specification".
NO
>> Repair or clean spark plug. Refer to EM-19, "Removal
and Installation". Then GO TO 9
1.
2.
SEF156I
9.CHECK FUNCTION OF IGNITION COIL-3
Reconnect the initial spark plugs.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded portion.
Spark should be generated.
10.CHECK FUEL INJECTOR
Turn ignition switch OFF.
Revision: August 2014
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace spark plug(s) with standard type one(s). For spark plug type, refer to EM-120,
"General Specification".
1.
EC-307
2015 Rogue NAM
P0420 THREE WAY CATALYST FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Remove fuel injector assembly.
Refer to EM-45, "Exploded View".
Keep fuel hose and all fuel injectors connected to fuel tube.
3. Disconnect all ignition coil harness connectors.
4. Reconnect all fuel injector harness connectors disconnected.
5. Turn ignition switch ON.
Does fuel drip from fuel injector?
YES >> GO TO 11.
NO
>> Replace the fuel injector(s) from which fuel is dripping. Refer to EM-45, "Exploded View".
11.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
Is the trouble fixed?
YES >> INSPECTION END
NO
>> Replace three way catalyst assembly. Refer to EM-32, "Exploded View".
Revision: August 2014
EC-308
2015 Rogue NAM
P0441 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0441 EVAP CONTROL SYSTEM
DTC Description
INFOID:0000000011278028
DTC DETECTION LOGIC
EC
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions.
Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP
canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.
Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow
are adequate. If not, a malfunction is determined.
JSBIA0416GB
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0441
EVAP PURG FLOW/MON
(Evaporative emission system incorrect
purge flow)
DTC detecting condition
EVAP control system does not operate properly, EVAP control system has
a leak between intake manifold and EVAP control system pressure sensor.
POSSIBLE CAUSE
EVAP canister purge volume control solenoid valve stuck closed
EVAP control system pressure sensor and the circuit
Loose, disconnected or improper connection of rubber tube
Blocked rubber tube
Cracked EVAP canister
EVAP canister purge volume control solenoid valve circuit
Accelerator pedal position sensor
Blocked purge port
EVAP canister vent control valve
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0441 is displayed with DTC P2122, P2123, P2127, P2128 or P2138, first perform the trouble diagnosis for DTC P2122, P2123, P2127, P2128 or P2138.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
Revision: August 2014
EC-309
2015 Rogue NAM
P0441 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Will CONSULT be used?
YES >> GO TO 3.
NO
>> GO TO 6.
3.PERFORM DTC CONFIRMATION PROCEDURE-1
WITH CONSULT
TESTING CONDITION:
Always perform test at a temperature of 5C (41F) or more.
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and let it idle for at least 70 seconds.
6. Select PURG FLOW P0441 of EVAPORATIVE SYSTEM in DTC WORK SUPPORT mode of
ENGINE using CONSULT.
7. Touch START.
Is COMPLETED displayed on CONSULT screen?
YES >> GO TO 5.
NO
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE-2
When the following conditions are met, TESTING will be displayed on the CONSULT screen. Maintain the
conditions continuously until TESTING changes to COMPLETED. (It will take at least 35 seconds.)
Selector lever
Suitable position
VHCL SPEED SE
32 - 120 km/h (20 - 75 MPH)
ENG SPEED
500 - 3,800 rpm
B/FUEL SCHDL
1.0 - 10.0 msec
COOLAN TEMP/S
More than 0C (32F)
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If TESTING does not change for a long time, retry from step 2.
Is COMPLETED displayed on CONSULT screen?
YES >> GO TO 5.
NO
>> Perform DTC CONFIRMATION PROCEDURE again. GO TO 2.
5.PERFORM DTC CONFIRMATION PROCEDURE-3
Touch SELF-DIAG RESULTS.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to EC-311, "Diagnosis Procedure".
6.PERFORM COMPONENT FUNCTION CHECK
1.
2.
3.
4.
5.
Lift up drive wheels.
Start engine (VDC switch OFF) and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and wait at least 70 seconds.
Set voltmeter probes to ECM harness connector terminals as per the following.
Revision: August 2014
EC-310
2015 Rogue NAM
P0441 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
+
Connector
Terminal
E16
6.
7.
114
EC
124
Check EVAP control system pressure sensor value at idle speed and note it.
Establish and maintain the following conditions for at least 1 minute.
Air conditioner switch
ON
Headlamp switch
ON
Rear window defogger switch
ON
Engine speed
Approx. 3,000 rpm
Gear position
Any position other than P, N or R
8.
Verify that EVAP control system pressure sensor value stays 0.1 V less than the value at idle speed (measured at step 6) for at least 1 second.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-311, "Diagnosis Procedure".
Diagnosis Procedure
If DTC P0441 is displayed with DTC P2122, P2123, P2127, P2128 or P2138, first perform the trouble diagnosis for DTC P2122, P2123, P2127, P2128 or P2138.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK EVAP CANISTER
1. Turn ignition switch OFF.
2. Check EVAP canister for cracks.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 3.
YES-2 >> Without CONSULT: GO TO 4.
NO
>> Replace EVAP canister. Refer to FL-19, "Removal and Installation".
3.CHECK PURGE FLOW
WITH CONSULT
1. Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port.
2. Start engine and let it idle.
3. Select PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT.
4. Touch Qd and Qu on CONSULT screen to adjust PURG VOL CONT/V opening and check vacuum
existence.
Vacuum
100%
Existed
0%
Not existed
Is the inspection result normal?
YES >> GO TO 8.
NO
>> GO TO 5.
4.CHECK PURGE FLOW
Revision: August 2014
INFOID:0000000011278029
1.CHECK DTC PRIORITY
PURG VOL CONT/V
EC-311
2015 Rogue NAM
P0441 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
WITHOUT CONSULT
Start engine and warm it up to normal operating temperature.
Stop engine.
Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP service port and install vacuum gauge. For the location of EVAP service port, refer to EC-55, "EVAPORATIVE
EMISSION SYSTEM : System Description".
4. Start engine and let it idle.
Never depress accelerator pedal even slightly.
5. Check vacuum gauge indication before 60 seconds pass after starting engine.
1.
2.
3.
Vacuum should not exist.
6.
Rev engine up to 2,000 rpm after 100 seconds pass after starting engine.
Vacuum should exist.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> GO TO 5.
5.CHECK EVAP PURGE LINE
1.
2.
Turn ignition switch OFF.
Check EVAP purge line for improper connection or disconnection.
Refer to EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair EVAP purge line.
6.CHECK EVAP PURGE HOSE AND PURGE PORT
1.
2.
Disconnect purge hoses connected to EVAP service port
EVAP canister purge volume control solenoid valve .
Blow air into each hose and EVAP purge port .
and
SEF367U
3. Check that air flows freely.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 7.
YES-2 >> Without CONSULT: GO TO 8.
NO
>> Repair or clean hoses and/or purge port.
7.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
SEF368U
WITH CONSULT
Start engine.
Perform PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT. Check that
engine speed varies according to the valve opening.
Does engine speed vary according to the valve opening?
1.
2.
Revision: August 2014
EC-312
2015 Rogue NAM
P0441 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 9.
NO
>> GO TO 8.
8.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Check the EVAP canister purge volume control solenoid valve. Refer to EC-318, "Component Inspection".
EC
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace EVAP canister purge volume control solenoid valve. Refer to EC-14,
C
"Component Parts Location".
9.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1. Disconnect EVAP control system pressure sensor harness connector.
2. Check that water is not inside connectors.
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
10.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR FUNCTION
Refer to EC-334, "DTC Description" for DTC P0452, EC-337, "DTC Description" for DTC P0453.
Is the inspection result normal?
YES >> GO TO 11.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
11.CHECK RUBBER TUBE FOR CLOGGING
1. Disconnect rubber tube connected to EVAP canister vent control valve.
2. Check the rubber tube for clogging.
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Clean the rubber tube using an air blower.
12.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the EVAP canister vent control valve. Refer to EC-324, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 13.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
13.CHECK EVAP PURGE LINE
Inspect EVAP purge line (pipe and rubber tube). Check for evidence of leaks.
Refer to EC-499, "Inspection".
Is the inspection result normal?
YES >> GO TO 14.
NO
>> Repair or replace malfunctioning part.
14.CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
O
>> GO TO 15.
15.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-313
2015 Rogue NAM
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
DTC Description
INFOID:0000000011278030
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0443
PURG VOLUME CONT/V
(Evaporative emission system purge control valve circuit)
DTC detecting condition
The canister purge flow is detected during the vehicle is stopped while
the engine is running, even when EVAP canister purge volume control
solenoid valve is completely closed.
The canister purge flow is detected during the specified driving conditions, even when EVAP canister purge volume control solenoid valve
is completely closed.
POSSIBLE CAUSE
EVAP control system pressure sensor
EVAP canister purge volume control solenoid valve (The valve is stuck open.)
EVAP canister vent control valve
EVAP canister
Hoses (Hoses are connected incorrectly or clogged.)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Perform DTC CONFIRMATION PROCEDURE when the fuel is between 1/4 and 3/4 full, and vehicle is
placed on flat level surface.
Always perform test at a temperature of 5 to 60C (41 to 140F).
Cool the vehicle so that engine coolant temperature becomes same level as ambient temperature.
Do you have CONSULT
YES >> GO TO 2.
NO
>> GO TO 4.
2.PERFORM DTC CONFIRMATION PROCEDURE A
With CONSULT
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Check that the following condition are met.
FUEL T/TMP SE: 0 - 35C (32 - 95F)
4. Start engine and wait at least 60 seconds.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-315, "Diagnosis Procedure".
NO
>> GO TO 3.
1.
2.
3.
3.PERFORM DTC CONFIRMATION PROCEDURE B
1.
2.
3.
With CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Revision: August 2014
EC-314
2015 Rogue NAM
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4. Select PURG VOL CN/V P1444 of EVAPORATIVE SYSTEM in DTC WORK SUPPORT mode of
ENGINE using CONSULT.
A
5. Touch START.
6. Start engine and let it idle until TESTING on CONSULT changes to COMPLETED. (It will take approximately 10 seconds.)
EC
If TESTING is not displayed after 5 minutes, retry from step 2.
7. Touch SELF-DIAG RESULT.
Which is displayed on CONSULT?
C
OK
>> INSPECTION END
NG
>> Proceed to EC-315, "Diagnosis Procedure".
4.PERFORM DTC CONFIRMATION PROCEDURE A
1.
2.
With GST
Turn ignition switch ON.
Check the voltage between ECM harness connector and ground.
Voltage
Ground
3.1 - 4.0 V
ECM
Connector
Terminal
E16
125
3. Start engine and wait at least 60 seconds.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-315, "Diagnosis Procedure".
NO
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE
With GST
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and let it idle for at least 20 seconds.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-315, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278031
1.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
Turn ignition switch ON.
Check the voltage between EVAP canister purge volume control solenoid valve harness connector and
ground.
+
EVAP canister purge volume
control solenoid valve
Connector
Terminal
F16
Voltage
P
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
Revision: August 2014
EC-315
2015 Rogue NAM
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
IPDM E/R harness connector.
+
EVAP canister purge volume
control solenoid valve
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F16
F35
73
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
ECM harness connector.
+
EVAP canister purge volume
control solenoid valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F16
F51
17
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
2.
Disconnect EVAP control system pressure sensor harness connector.
Check connectors for water.
Water should not exist.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
5.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to EC-318, "Component Inspection".
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 6.
YES-2 >> Without CONSULT: GO TO 7.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
6.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT
Turn ignition switch OFF.
Reconnect harness connectors disconnected.
Start engine.
Perform PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT. Check that
engine speed varies according to the valve opening.
Is the inspection result normal?
1.
2.
3.
4.
Revision: August 2014
EC-316
2015 Rogue NAM
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 8.
NO
>> GO TO 7.
7.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Check the EVAP canister purge volume control solenoid valve. Refer to EC-318, "Component Inspection".
EC
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace EVAP canister purge volume control solenoid valve. Refer to EC-14,
C
"Component Parts Location".
8.CHECK RUBBER TUBE FOR CLOGGING
1. Disconnect rubber tube connected to EVAP canister vent control valve.
2. Check the rubber tube for clogging.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Clean the rubber tube using an air blower.
9.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the EVAP canister vent control valve. Refer to EC-324, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
10.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Check if water will drain from EVAP canister.
Does water drain from the EVAP canister?
YES >> GO TO 11.
NO
>> GO TO 13.
K
PBIB1213E
11.CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES >> GO TO 13.
NO
>> GO TO 12.
12.DETECT MALFUNCTIONING PART
Check the following.
EVAP canister for damage
EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister. Refer to FL-19, "Removal and Installation".
13.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-317
2015 Rogue NAM
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Component Inspection
INFOID:0000000011278032
1.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
1.
2.
3.
4.
5.
6.
With CONSULT
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
Start engine.
Select PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT.
Touch Qd and Qu on CONSULT screen to adjust PURG
VOL C/V opening and check air passage continuity of EVAP
canister purge volume control solenoid valve as per the following conditions.
Condition
(PURG VOL C/V value)
Air passage continuity
100%
Existed
0%
Not existed
between
and
JMBIA0068ZZ
1.
2.
3.
4.
Without CONSULT
Turn ignition switch OFF.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
Check air passage continuity of EVAP canister purge volume
control solenoid valve as per the following conditions.
Condition
12 V direct current supply between
terminals 1 and 2
No supply
Air passage continuity
between
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP canister purge
"Component Parts Location".
Revision: August 2014
and
JMBIA0068ZZ
volume
EC-318
control
solenoid
valve.
Refer
to
EC-14,
2015 Rogue NAM
P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID
VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID
VALVE
DTC Description
INFOID:0000000011278033
EC
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0444
PURG VOLUME CONT/V
(Evaporative emission system purge control valve circuit open)
An excessively low voltage signal is sent to ECM through the EVAP canister purge volume control solenoid valve.
P0445
PURG VOLUME CONT/V
(Evaporative emission system purge control valve circuit shorted)
An excessively high voltage signal is sent to ECM through the valve
POSSIBLE CAUSE
DTC P0444
Harness or connectors (EVAP canister purge volume control solenoid valve circuit is open or shorted.)
EVAP canister purge volume control solenoid valve
DTC P0445
Harness or connectors (EVAP canister purge volume control solenoid valve circuit is shorted.)
EVAP canister purge volume control solenoid valve
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11 V at idle.
1.CONDITIONING
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 13 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-319, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278034
1.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
Turn ignition switch ON.
Check the voltage between EVAP canister purge volume control solenoid valve harness connector and
ground.
Revision: August 2014
EC-319
2015 Rogue NAM
P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID
VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
EVAP canister purge volume
control solenoid valve
Connector
Terminal
F16
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
IPDM E/R harness connector.
+
EVAP canister purge volume
control solenoid valve
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F16
F35
73
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
ECM harness connector.
+
EVAP canister purge volume
control solenoid valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F16
F51
17
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 4.
YES-2 >> Without CONSULT: GO TO 5.
NO
>> Repair or replace error-detected parts.
4.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT
1. Reconnect all harness connectors disconnected.
2. Start engine.
3. Perform PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT.
4. Check that engine speed varies according to the valve opening.
Does engine speed vary according to the valve opening?
YES >> GO TO 6.
NO
>> GO TO 5.
5.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Revision: August 2014
EC-320
2015 Rogue NAM
P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID
VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Check the EVAP canister purge volume control solenoid valve. Refer to EC-318, "Component Inspection".
A
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace EVAP canister purge volume control solenoid valve. Refer to EC-14,
"Component Parts Location".
EC
CHECK INTERMITTENT INCIDENT
6.
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278035
1.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
4. Start engine.
5. Select PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT.
6. Touch Qd and Qu on CONSULT screen to adjust PURG
VOL C/V opening and check air passage continuity of EVAP
canister purge volume control solenoid valve as per the following conditions.
Condition
(PURG VOL C/V value)
Air passage continuity
100%
Existed
0%
Not existed
between
and
JMBIA0068ZZ
1.
2.
3.
4.
Without CONSULT
Turn ignition switch OFF.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
Check air passage continuity of EVAP canister purge volume
control solenoid valve as per the following conditions.
Condition
12 V direct current supply between
terminals 1 and 2
No supply
Air passage continuity
between
and
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP canister purge
"Component Parts Location".
JMBIA0068ZZ
volume
control
solenoid
valve.
Refer
to
EC-14,
Revision: August 2014
EC-321
2015 Rogue NAM
P0447 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0447 EVAP CANISTER VENT CONTROL VALVE
DTC Description
INFOID:0000000011278036
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
VENT CONTROL VALVE
(Evaporative emission system vent control
circuit open)
An improper voltage signal is sent to ECM through EVAP canister vent control valve.
DTC No.
P0447
POSSIBLE CAUSE
Harness or connectors (EVAP canister vent control valve circuit is open or shorted.)
EVAP canister vent control valve
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait at least 8 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-322, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278037
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 3.
2.CHECK EVAP CANISTER VENT CONTROL VALVE CIRCUIT
1.
2.
3.
4.
With CONSULT
Turn ignition switch OFF and then turn ON.
Select VENT CONTROL/V in ACTIVE TEST mode of ENGINE using CONSULT.
Touch ON/OFF on CONSULT screen.
Check for operating sound of the valve.
Clicking sound should be heard.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> GO TO 3.
Revision: August 2014
EC-322
2015 Rogue NAM
P0447 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
3.CHECK EVAP CANISTER VENT CONTROL VALVE POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect EVAP canister vent control valve harness connector.
Turn ignition switch ON.
Check the voltage between EVAP canister vent control valve harness connector and ground.
+
Voltage
Ground
Battery voltage
EVAP canister vent control valve
Connector
Terminal
B108
EC
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK EVAP CANISTER VENT CONTROL VALVE POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between EVAP canister vent control valve harness connector and IPDM E/R harness
connector.
+
EVAP canister vent control
valve
IPDM E/R
Connector
Terminal
Connector
Terminal
B108
F35
78
Existed
5.CHECK EVAP CANISTER VENT CONTROL VALVE OUTPUT SIGNAL CIRCUIT
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP canister vent control valve harness connector and ECM harness connector.
+
EVAP canister vent control
valve
ECM
M
Continuity
Connector
Terminal
Connector
Terminal
B108
E16
97
N
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK RUBBER TUBE FOR CLOGGING
1. Disconnect rubber tube connected to EVAP canister vent control valve.
2. Check the rubber tube for clogging.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Clean the rubber tube using an air blower.
Revision: August 2014
Continuity
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
1.
2.
3.
EC-323
2015 Rogue NAM
P0447 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
7.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the EVAP canister vent control valve. Refer to EC-324, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation"
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278038
1.CHECK EVAP CANISTER VENT CONTROL VALVE-1
1.
2.
3.
Turn ignition switch OFF.
Remove EVAP canister vent control valve from EVAP canister.
Check portion
of EVAP canister vent control valve for being
rusted.
Is it rusted?
YES >> Replace EVAP canister vent control valve. Refer to FL21, "Removal and Installation".
NO
>> GO TO 2.
JMBIA0168ZZ
2.CHECK EVAP CANISTER VENT CONTROL VALVE-2
1.
2.
3.
4.
With CONSULT
Reconnect harness connectors disconnected.
Turn ignition switch ON.
Perform VENT CONTROL/V in ACTIVE TEST mode of ENGINE using CONSULT.
Check air passage continuity and operation delay time.
Make sure new O-ring is installed properly.
Condition
(VENT CONT/V)
Air passage continuity between
ON
Not existed
OFF
Existed
and
Operation takes less than 1 second.
JMBIA0169ZZ
Without CONSULT
Check air passage continuity and operation delay time under the following conditions.
Make sure new O-ring is installed properly.
Condition
12 V direct current supply between
terminals 1 and 2
OFF
Air passage continuity between
and
Not existed
Existed
Operation takes less than 1 second.
JMBIA0169ZZ
Revision: August 2014
EC-324
2015 Rogue NAM
P0447 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
3.CHECK EVAP CANISTER VENT CONTROL VALVE-3
EC
With CONSULT
1. Clean the air passage [portion
to ] of EVAP canister vent control valve using an air blower.
2. Perform VENT CONTROL/V in ACTIVE TEST mode of ENGINE using CONSULT.
3. Check air passage continuity and operation delay time.
Make sure new O-ring is installed properly.
Condition
(VENT CONT/V)
D
Air passage continuity between
ON
Not existed
OFF
Existed
and
Operation takes less than 1 second.
F
JMBIA0169ZZ
1.
2.
Without CONSULT
Clean the air passage [portion to ] of EVAP canister vent control valve using an air blower.
Check air passage continuity and operation delay time under the
following conditions.
Make sure new O-ring is installed properly.
Condition
Air passage continuity between
12 V direct current supply between
terminals 1 and 2
OFF
and
Not existed
Existed
Operation takes less than 1 second.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
JMBIA0169ZZ
Revision: August 2014
EC-325
2015 Rogue NAM
P0448 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0448 EVAP CANISTER VENT CONTROL VALVE
DTC Description
INFOID:0000000011278039
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0448
VENT CONTROL VALVE
(Evaporative emission system vent control
circuit shorted)
DTC detecting condition
EVAP canister vent control valve remains closed under specified driving
conditions.
POSSIBLE CAUSE
EVAP canister vent control valve
EVAP control system pressure sensor and the circuit
Blocked rubber tube to EVAP canister vent control valve
EVAP canister is saturated with water
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and wait at least 5 seconds.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON and select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and let it idle for at least 1 minute.
Repeat next procedures three times.
Increase the engine speed up to 3,000 to 3,500 rpm and keep it for 2 minutes and 50 seconds to 3 minutes.
Never exceed 3 minutes.
Fully released accelerator pedal and keep engine idle for about 5 seconds.
6. Repeat next procedure 20 times.
Quickly increase the engine speed up to 4,000 to 4,500 rpm or more and keep it for 25 to 30 seconds.
Fully released accelerator pedal and keep engine idle for at least 35 seconds.
1.
2.
3.
4.
5.
-
PBIB0972E
7.
Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
Revision: August 2014
EC-326
2015 Rogue NAM
P0448 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> Proceed to EC-327, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278040
1.CHECK RUBBER TUBE
EC
1. Turn ignition switch OFF.
2. Disconnect rubber tube connected to EVAP canister vent control valve.
3. Check the rubber tube for clogging.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Clean rubber tube using an air blower.
2.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the EVAP canister vent control valve. Refer to EC-328, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
3.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Check if water will drain from the EVAP canister.
Does water drain from EVAP canister?
YES >> GO TO 4.
NO
>> GO TO 6.
J
PBIB1213E
4.CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES >> GO TO 6.
NO
>> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following.
EVAP canister for damage
EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister. Refer to FL-19, "Removal and Installation".
6.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
2.
Disconnect EVAP control system pressure sensor harness connector.
Check connectors for water.
Water should not exist.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
Revision: August 2014
EC-327
2015 Rogue NAM
P0448 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
7.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to EC-333, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278041
1.CHECK EVAP CANISTER VENT CONTROL VALVE-1
1.
2.
3.
Turn ignition switch OFF.
Remove EVAP canister vent control valve from EVAP canister.
Check portion
of EVAP canister vent control valve for being
rusted.
Is it rusted?
YES >> Replace EVAP canister vent control valve. Refer to FL21, "Removal and Installation".
NO
>> GO TO 2.
JMBIA0168ZZ
2.CHECK EVAP CANISTER VENT CONTROL VALVE-2
1.
2.
3.
4.
With CONSULT
Reconnect harness connectors disconnected.
Turn ignition switch ON.
Perform VENT CONTROL/V in ACTIVE TEST mode of ENGINE using CONSULT.
Check air passage continuity and operation delay time.
Make sure new O-ring is installed properly.
Condition
(VENT CONT/V)
Air passage continuity between
ON
Not existed
OFF
Existed
and
Operation takes less than 1 second.
JMBIA0169ZZ
Without CONSULT
Check air passage continuity and operation delay time under the following conditions.
Make sure new O-ring is installed properly.
Condition
12 V direct current supply between
terminals 1 and 2
OFF
Air passage continuity between
and
Not existed
Existed
Operation takes less than 1 second.
JMBIA0169ZZ
Revision: August 2014
EC-328
2015 Rogue NAM
P0448 EVAP CANISTER VENT CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
3.CHECK EVAP CANISTER VENT CONTROL VALVE-3
EC
With CONSULT
1. Clean the air passage [portion
to ] of EVAP canister vent control valve using an air blower.
2. Perform VENT CONTROL/V in ACTIVE TEST mode of ENGINE using CONSULT.
3. Check air passage continuity and operation delay time.
Make sure new O-ring is installed properly.
Condition
(VENT CONT/V)
D
Air passage continuity between
ON
Not existed
OFF
Existed
and
Operation takes less than 1 second.
F
JMBIA0169ZZ
1.
2.
Without CONSULT
Clean the air passage [portion to ] of EVAP canister vent control valve using an air blower.
Check air passage continuity and operation delay time under the
following conditions.
Make sure new O-ring is installed properly.
Condition
Air passage continuity between
12 V direct current supply between
terminals 1 and 2
OFF
and
Not existed
Existed
Operation takes less than 1 second.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
JMBIA0169ZZ
Revision: August 2014
EC-329
2015 Rogue NAM
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC Description
INFOID:0000000011278042
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0451
EVAP SYS PRES SEN
(Evaporative emission system pressure
sensor/switch range/performance)
DTC detecting condition
ECM detects a sloshing signal from the EVAP control system pressure sensor
POSSIBLE CAUSE
Harness or connectors (EVAP control system pressure sensor circuit is shorted.)
EVAP control system pressure sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
NOTE:
Never remove fuel filler cap during DTC confirmation procedure.
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
With CONSULT>>GO TO 2.
Without CONSULT>>GO TO 5.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
Start engine and let it idle for least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-331, "Diagnosis Procedure".
NO
>> GO TO 3.
1.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
Select EVAP DIAG READY in DATA MONITOR mode of ENGINE.
Let it idle until OFF of EVAP DIAG READY changes to ON.
NOTE:
It will take at most 2 hours until OFF of EVAP DIAG READY changes to ON.
3. Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
4. Turn ignition switch ON.
5. Select EVAP LEAK DIAG in DATA MONITOR mode of ENGINE.
6. Check that EVAP LEAK DIAG indication.
Which is displayed on CONSULT?
CMPLT >> GO TO 4.
YET >> 1. Perform DTC CONFIRMATION PROCEDURE again.
2. GO TO 1.
1.
2.
Revision: August 2014
EC-330
2015 Rogue NAM
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4.PERFORM DTC CONFIRMATION PROCEDURE-3
With CONSULT
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-331, "Diagnosis Procedure".
NO
>> INSPECTION END
EC
5.PERFORM DTC CONFIRMATION PROCEDURE-4
With GST
Start engine and let it idle for least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-331, "Diagnosis Procedure".
NO
>> GO TO 6.
1.
6.PERFORM DTC CONFIRMATION PROCEDURE-5
With GST
Let it idle for at least 2 hours.
Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-331, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
Diagnosis Procedure
INFOID:0000000011278043
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.
2.
3.
Turn ignition switch OFF.
Disconnect EVAP control system pressure sensor harness connector.
Check sensor harness connector for water.
Water should not exist.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace harness connector.
2.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY
1.
2.
Turn ignition switch ON.
Check the voltage between EVAP control system pressure sensor harness connector and ground.
+
EVAP control system pressure sensor
Connector
Terminal
B111
Voltage
(Approx.)
P
Ground
5V
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
Revision: August 2014
EC-331
2015 Rogue NAM
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
113
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts
4.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
124
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR SIGNAL CIRCUIT
1.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
114
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to EC-333, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
Revision: August 2014
EC-332
2015 Rogue NAM
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> INSPECTION END
Component Inspection
INFOID:0000000011278044
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
2.
3.
4.
EC
Turn ignition switch OFF.
Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Always replace O-ring with a new one.
Install a vacuum pump to EVAP control system pressure sensor.
Turn ignition switch ON and check output voltage between ECM harness connector and ground under the
following conditions.
ECM
Connector
E16
+
Terminal
114
124
Condition
[Applied vacuum kPa (kg/cm2, psi)]
Not applied
Voltage
0.5 - 4.6 V
-26.7 (-0.272, -3.87)
2.1 to 2.5 V lower than above value
CAUTION:
Always calibrate the vacuum pump gauge when using it.
Do not apply below -93.3 kPa (-0.952 kg/cm2, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/
cm2, 14.69 psi).
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
Revision: August 2014
EC-333
2015 Rogue NAM
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC Description
INFOID:0000000011278045
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
EVAP SYS PRES SEN
(Evaporative emission system pressure
sensor/switch low)
P0452
DTC detecting condition
An excessively low voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (EVAP control system pressure sensor circuit is shorted.)
EVAP control system pressure sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Always perform test at a temperature of 5C (41F) or more.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Make sure that FUEL T/TMP SE indication is more than 0C (32F).
Start engine and wait at least 20 seconds.
Check 1st trip DTC.
With GST
1. Start engine and warm it up to normal operating temperature.
2. Set voltmeter probes to ECM harness connector terminals as per the following.
1.
2.
3.
4.
5.
6.
7.
ECM
Connector
E16
Voltage
124
Less than 4.2 V
Terminal
114
3. Make sure that the voltage is less than 4.2 V.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and wait at least 20 seconds.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-335, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-334
2015 Rogue NAM
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278046
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.
2.
3.
Turn ignition switch OFF.
Disconnect EVAP control system pressure sensor harness connector.
Check sensor harness connector for water.
EC
Water should not exist.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace harness connector.
2.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY
1.
2.
Turn ignition switch ON.
Check the voltage between EVAP control system pressure sensor harness connector and ground.
+
EVAP control system pressure sensor
Connector
Terminal
B111
Voltage
(Approx.)
G
Ground
5V
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
K
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
113
L
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts
4.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
4.
P
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
124
Existed
Also check harness for short to power.
Revision: August 2014
EC-335
2015 Rogue NAM
P0452 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR SIGNAL CIRCUIT
1.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
114
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to EC-333, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278047
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Always replace O-ring with a new one.
Install a vacuum pump to EVAP control system pressure sensor.
Turn ignition switch ON and check output voltage between ECM harness connector and ground under the
following conditions.
ECM
Connector
E16
+
Terminal
114
124
Condition
[Applied vacuum kPa (kg/cm2, psi)]
Not applied
Voltage
0.5 - 4.6 V
-26.7 (-0.272, -3.87)
2.1 to 2.5 V lower than above value
CAUTION:
Always calibrate the vacuum pump gauge when using it.
Do not apply below -93.3 kPa (-0.952 kg/cm2, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/
cm2, 14.69 psi).
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
Revision: August 2014
EC-336
2015 Rogue NAM
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
DTC Description
A
INFOID:0000000011278048
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
EVAP SYS PRES SEN
(Evaporative emission system pressure
sensor/switch high)
P0453
DTC detecting condition
An excessively high voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (EVAP control system pressure sensor circuit is shorted.)
EVAP control system pressure sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Always perform test at a temperature of 5C (41F) or more.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Make sure that FUEL T/TMP SE indication is more than 0C (32F).
Start engine and wait at least 20 seconds.
Check 1st trip DTC.
With GST
1. Start engine and warm it up to normal operating temperature.
2. Set voltmeter probes to ECM harness connector terminals as per the following.
1.
2.
3.
4.
5.
6.
7.
ECM
Connector
E16
Voltage
124
Less than 4.2 V
Terminal
114
3. Make sure that the voltage is less than 4.2 V.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Start engine and wait at least 20 seconds.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-338, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-337
2015 Rogue NAM
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278049
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.
2.
3.
Turn ignition switch OFF.
Disconnect EVAP control system pressure sensor harness connector.
Check sensor harness connector for water.
Water should not exist.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace harness connector.
2.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY
1.
2.
Turn ignition switch ON.
Check the voltage between EVAP control system pressure sensor harness connector and ground.
+
EVAP control system pressure sensor
Connector
Terminal
B111
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
113
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts
4.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
4.
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
124
Existed
Also check harness for short to power.
Revision: August 2014
EC-338
2015 Rogue NAM
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR SIGNAL CIRCUIT
1.
Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
+
EVAP control system pressure sensor
ECM
EC
C
Continuity
Connector
Terminal
Connector
Terminal
B111
E16
114
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
1. Disconnect rubber tube connected to EVAP canister vent control valve.
2. Check the rubber tube for clogging.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Clean the rubber tube using an air blower, repair or replace rubber tube.
Refer to EC-324, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace EVAP canister vent control valve. Refer to FL-21, "Removal and Installation".
6.CHECK RUBBER TUBE
7.CHECK EVAP CANISTER VENT CONTROL VALVE
8.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to EC-340, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
1.
9.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Check if water will drain from the EVAP canister.
Does water drain from EVAP canister?
YES >> GO TO 10.
NO
>> GO TO 12.
P
PBIB1213E
10.CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 1.9 kg (4.2 lb).
Revision: August 2014
EC-339
2015 Rogue NAM
P0453 EVAP CONTROL SYSTEM PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 12.
NO
>> GO TO 11.
11.DETECT MALFUNCTIONING PART
Check the following.
EVAP canister for damage
EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister. Refer to FL-19, "Removal and Installation".
12.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278050
1.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Always replace O-ring with a new one.
Install a vacuum pump to EVAP control system pressure sensor.
Turn ignition switch ON and check output voltage between ECM harness connector and ground under the
following conditions.
ECM
Connector
E16
+
Terminal
114
124
Condition
[Applied vacuum kPa (kg/cm2, psi)]
Not applied
Voltage
0.5 - 4.6 V
-26.7 (-0.272, -3.87)
2.1 to 2.5 V lower than above value
CAUTION:
Always calibrate the vacuum pump gauge when using it.
Do not apply below -93.3 kPa (-0.952 kg/cm2, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/
cm2, 14.69 psi).
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
Revision: August 2014
EC-340
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0456 EVAP CONTROL SYSTEM
DTC Description
INFOID:0000000011278051
DTC DETECTION LOGIC
EC
This diagnosis detects leaks in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve, using the negative pressure caused by decrease of fuel temperature in the fuel tank after turning
ignition switch OFF.
If ECM judges there are no leaks, the diagnosis will be OK.
H
JSBIA0416GB
DTC No.
P0456
CONSULT screen terms
(Trouble diagnosis content)
EVAP VERY SML LEAK
[Evaporative emission system leak detected (very small leak)]
DTC detecting condition
EVAP system has a leak.
EVAP system does not operate properly.
CAUTION:
Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may illuminate.
If the fuel filler cap is not tightened properly, the MIL may illuminate.
Use only a genuine NISSAN rubber tube as a replacement.
POSSIBLE CAUSE
Incorrect fuel tank vacuum relief valve
Incorrect fuel filler cap used
Fuel filler cap remains open or does not close.
Foreign matter caught in fuel filler cap.
Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve.
Foreign matter caught in EVAP canister vent control valve.
EVAP canister or fuel tank leaks
EVAP purge line (pipe and rubber tube) leaks
EVAP purge line rubber tube bent
Loose or disconnected rubber tube
EVAP canister vent control valve and the circuit
EVAP canister purge volume control solenoid valve and the circuit
Fuel tank temperature sensor
O-ring of EVAP canister vent control valve is missing or damaged
EVAP canister is saturated with water
EVAP control system pressure sensor
Refueling EVAP vapor cut valve
ORVR system leaks
Fuel level sensor and the circuit
Foreign matter caught in EVAP canister purge volume control solenoid valve
Revision: August 2014
EC-341
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 4.
2.PERFORM DTC CONFIRMATION PROCEDURE-1
WITH CONSULT
Turn ignition switch ON and select EVAP DIAG READY in DATA MONITOR mode of ENGINE using
CONSULT.
2. Start engine and wait at idle until OFF of EVAP DIAG READY changes to ON.
NOTE:
It will take at most 2 hours until OFF of EVAP DIAG READY changes to ON.
3. Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
4. Turn ignition switch ON and select EVAP LEAK DIAG in DATA MONITOR mode of ENGINE using
CONSULT.
5. Check that EVAP LEAK DIAG indication.
Which is displayed on CONSULT?
CMPLT >> GO TO 3.
YET >> Perform DTC CONFIRMATION PROCEDURE again. GO TO 1.
1.
3.PERFORM DTC CONFIRMATION PROCEDURE-2
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed toEC-342, "Diagnosis Procedure".
NO
>> INSPECTION END.
4.PERFORM DTC CONFIRMATION PROCEDURE
WITH GST
Start engine and wait engine idle for at least 2 hours.
Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-342, "Diagnosis Procedure".
NO
>> INSPECTION END.
1.
2.
Diagnosis Procedure
INFOID:0000000011278052
1.CHECK FUEL FILLER CAP DESIGN
1.
Turn ignition switch OFF.
Revision: August 2014
EC-342
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
< DTC/CIRCUIT DIAGNOSIS >
2. Check for genuine NISSAN fuel filler cap design.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace with genuine NISSAN fuel filler cap.
[QR25DE]
A
EC
C
SEF915U
2.CHECK FUEL FILLER CAP INSTALLATION
Check that the cap is tightened properly by rotating the cap clockwise.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Open fuel filler cap, then clean cap and fuel filler neck threads using air blower. Then retighten
until reteaching sound is heard.
3.CHECK FUEL FILLER CAP FUNCTION
Check for air releasing sound while opening the fuel filler cap.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK FUEL TANK VACUUM RELIEF VALVE
Refer to EC-346, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace fuel filler cap with a genuine one.
5.CHECK FOR EVAP LEAK
Refer to EC-499, "Inspection".
Is there any leak in EVAP line?
YES >> Repair or replace.
NO
>> GO TO 6.
6.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the following.
EVAP canister vent control valve is installed properly.
Refer to FL-21, "Exploded View".
EVAP canister vent control valve.
Refer to FL-21, "Removal and Installation".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace EVAP canister vent control valve and O-ring. Refer to FL-21, "Removal and
Installation".
7.CHECK IF EVAP CANISTER SATURATED WITH WATER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
Revision: August 2014
EC-343
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Check if water will drain from the EVAP canister.
Does water drain from EVAP canister?
YES >> GO TO 8.
NO-1 >> With CONSULT: GO TO 10.
NO-2 >> Without CONSULT: GO TO 11.
PBIB1213E
8.CHECK EVAP CANISTER
Weigh the EVAP canister assembly with the EVAP canister vent control valve and EVAP control system pressure sensor attached. Refer to FL-21, "Removal and Installation".
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 10.
YES-2 >> Without CONSULT: GO TO 11.
NO
>> GO TO 9.
9.DETECT MALFUNCTIONING PART
Check the following.
EVAP canister for damage
EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister. Refer to FL-19, "Removal and Installation".
10.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
1.
2.
3.
4.
5.
With CONSULT
Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
Start engine and let it idle.
Select PURG VOL CONT/V in ACTIVE TEST mode of ENGINE using CONSULT.
Touch Qu on CONSULT screen to increase PURG VOL CONT/V opening to 100%.
Check vacuum hose for vacuum.
Vacuum should exist.
Is the inspection result normal?
YES >> GO TO 13.
NO
>> GO TO 12.
11.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
1.
2.
3.
4.
5.
Without CONSULT
Start engine and warm it up to normal operating temperature.
Stop engine.
Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
Start engine and let it idle for at least 80 seconds.
Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
Vacuum should exist.
Is the inspection result normal?
YES >> GO TO 13.
NO
>> GO TO 12.
12.CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection.
Is the inspection result normal?
Revision: August 2014
EC-344
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 13.
NO
>> Repair or reconnect the hose.
13.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Check the EVAP canister purge volume control solenoid valve. Refer to EC-318, "Component Inspection".
EC
Is the inspection result normal?
YES >> GO TO 14.
NO
>> Replace EVAP canister purge volume control solenoid valve. Refer to EC-14,
C
"Component Parts Location".
14.CHECK FUEL TANK TEMPERATURE SENSOR
Check the fuel tank temperature sensor. Refer to EC-276, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 15.
NO
>> Replace fuel level sensor unit. Refer to FL-5, "Removal and Installation".
15.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Check the EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
Is the inspection result normal?
YES >> GO TO 16.
NO
>> Replace EVAP control system pressure sensor. Refer to FL-22, "Removal and Installation".
16.CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
Refer to EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description".
Is the inspection result normal?
YES >> GO TO 17.
NO
>> Repair or reconnect the hose.
17.CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 18.
18.CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kink, looseness and improper connection. For location, refer to EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description".
Is the inspection result normal?
YES >> GO TO 19.
NO
>> Repair or replace hoses and tubes.
19.CHECK RECIRCULATION LINE
Check recirculation line between fuel filler tube and fuel tank for clogging, kink, cracks, looseness and
improper connection.
Is the inspection result normal?
YES >> GO TO 20.
NO
>> Repair or replace hose, tube or fuel filler tube. Refer to FL-11, "FWD : Exploded View" (with FWD
models) or FL-15, "AWD : Exploded View" (with AWD models).
20.CHECK REFUELING EVAP VAPOR CUT VALVE
Check the refueling EVAP vapor cut valve. Refer to FL-14, "FWD : Inspection" (with FWD models) or FL-18,
"AWD : Inspection" (with AWD models).
Is the inspection result normal?
YES >> GO TO 21.
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) or FL-15, "AWD : Removal and Installation" (with AWD models).
Revision: August 2014
EC-345
2015 Rogue NAM
P0456 EVAP CONTROL SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
21.CHECK FUEL LEVEL SENSOR
Check the fuel level sensor. Refer to MWI-64, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 22.
NO
>> Replace fuel level sensor unit. Refer to FL-5, "Removal and Installation".
22.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278053
1.CHECK FUEL FILLER CAP
1.
2.
3.
Turn ignition switch OFF.
Remove fuel filler cap.
Wipe clean valve housing.
SEF445Y
4.
5.
Install fuel filler cap adapter (commercial service tool) to fuel
filler cap.
Check valve opening pressure and vacuum.
Pressure:
15.3 - 20.0 kPa (0.156 - 0.204 kg/cm2, 2.22
- 2.90 psi)
Vacuum:
6.0 to 3.3 kPa (0.061 to 0.034 kg/cm2,
0.87 to 0.48 psi)
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
SEF943S
2.REPLACE FUEL FILLER CAP
Replace fuel filler cap.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may
illuminate.
>> INSPECTION END
Revision: August 2014
EC-346
2015 Rogue NAM
P0460 FUEL LEVEL SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0460 FUEL LEVEL SENSOR
DTC Description
INFOID:0000000011278054
DTC DETECTION LOGIC
EC
When the vehicle is parked, naturally the fuel level in the fuel tank is stable. It means that output signal of the
fuel level sensor does not change. If ECM senses sloshing signal from the sensor, fuel level sensor malfunction is detected.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
FUEL LEV SEN SLOSH
(Fuel Level Sensor A Circuit)
P0460
DTC detecting condition
Even though the vehicle is parked, a signal being varied is sent from the
fuel level sensor to ECM.
POSSIBLE CAUSE
Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (The sensor circuit is open or shorted.)
Combination meter
Fuel level sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0460 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait maximum of 2 consecutive minutes.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-347, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278055
1.CHECK DTC PRIORITY
If DTC P0460 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK COMBINATION METER FUNCTION
Revision: August 2014
EC-347
2015 Rogue NAM
P0460 FUEL LEVEL SENSOR
< DTC/CIRCUIT DIAGNOSIS >
Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Refer to MWI-63, "Component Function Check".
[QR25DE]
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-348
2015 Rogue NAM
P0461 FUEL LEVEL SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0461 FUEL LEVEL SENSOR
DTC Description
INFOID:0000000011278056
DTC DETECTION LOGIC
EC
Driving long distances naturally affect fuel gauge level.
This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distance has
been driven.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
FUEL LEVEL SENSOR
(Fuel level sensor A circuit range/performance)
The output signal of the fuel level sensor does not change within the specified range even though the vehicle has been driven a long distance.
DTC No.
P0461
POSSIBLE CAUSE
Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (The sensor circuit is open or shorted.)
Combination meter
Fuel level sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
H
1.CHECK DTC PRIORITY
If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
WARNING:
When performing following procedure, be sure to observe the handling of the fuel. Refer to FL-2,
"General Precaution".
TESTING CONDITION:
Before starting component function check, preparation of draining fuel and refilling fuel is required.
Do you have CONSULT?
YES >> GO TO 3.
NO
>> GO TO 4.
3.PERFORM COMPONENT FUNCTION CHECK
With CONSULT
NOTE:
Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/
8 Imp gal) in advance.
1. Prepare a fuel container and a spare hose.
2. Release fuel pressure from fuel line, refer to EC-147, "Work Procedure".
3. Remove the fuel feed hose on the fuel level sensor unit.
4. Connect a spare fuel hose where the fuel feed hose was removed.
5. Turn ignition switch OFF and wait at least 10 seconds then turn ON.
6. Select FUEL LEVEL SE in DATA MONITOR mode of ENGINE using CONSULT.
7. Check FUEL LEVEL SE output voltage and note it.
8. Select FUEL PUMP RELAY in ACTIVE TEST mode of ENGINE using CONSULT.
9. Touch ON and drain fuel approximately 30 (7-7/8 US gal, 6-5/8 Imp gal) and stop it.
10. Check FUEL LEVEL SE output voltage and note it.
Revision: August 2014
EC-349
2015 Rogue NAM
P0461 FUEL LEVEL SENSOR
< DTC/CIRCUIT DIAGNOSIS >
11. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
12. Check FUEL LEVEL SE output voltage and note it.
13. Confirm whether the voltage changes more than 0.03 V during step 7 to 10 and 10 to 12.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-350, "Diagnosis Procedure".
[QR25DE]
4.PERFORM COMPONENT FUNCTION CHECK
Without CONSULT
NOTE:
Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/8
Imp gal) in advance.
1. Prepare a fuel container and a spare hose.
2. Release fuel pressure from fuel line. Refer to EC-147, "Work Procedure".
3. Remove the fuel feed hose on the fuel level sensor unit.
4. Connect a spare fuel hose where the fuel feed hose was removed.
5. Turn ignition switch ON.
6. Drain fuel by 30 (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.
7. Confirm that the fuel gauge indication varies.
8. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
9. Confirm that the fuel gauge indication varies.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-350, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278057
1.CHECK DTC PRIORITY
If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK COMBINATION METER FUNCTION
Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Refer to MWI-63, "Component Function Check"
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-350
2015 Rogue NAM
P0462, P0463 FUEL LEVEL SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0462, P0463 FUEL LEVEL SENSOR
DTC Description
INFOID:0000000011278058
DTC DETECTION LOGIC
EC
This diagnosis indicates the former, to detect open or short circuit malfunction.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0462
FUEL LEVL SEN/CIRC
(Fuel level sensor A circuit low)
An excessively low voltage from the sensor is sent to ECM.
P0463
FUEL LEVL SEN/CIRC
(Fuel level sensor A circuit high)
An excessively high voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (The sensor circuit is open or shorted.)
Combination meter
Fuel level sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0462 or P0463 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC
UXXXX or P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 11 V and 16 V at
ignition switch ON.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-351, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278059
1.CHECK DTC PRIORITY
If DTC P0462 or P0463 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC
UXXXX or P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK COMBINATION METER FUNCTION
Revision: August 2014
EC-351
2015 Rogue NAM
P0462, P0463 FUEL LEVEL SENSOR
< DTC/CIRCUIT DIAGNOSIS >
Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Proceed to MWI-63, "Component Function Check".
[QR25DE]
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-352
2015 Rogue NAM
P0500 VSS
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0500 VSS
Description
INFOID:0000000011278060
ECM receives vehicle speed signals from two different paths via CAN communication line: One is from the EC
ABS actuator and electric unit (control unit) via the combination unit and the other is from TCM.
DTC Description
INFOID:0000000011278061
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
VEHICLE SPEED SENSOR A
(Vehicle speed sensor A)
P0500
DTC detecting condition
At 20 km/h (13 MPH), ECM detects the following status continuously for 5
seconds or more: The difference between a vehicle speed calculated by a
output speed sensor transmitted from TCM to ECM via CAN communication and the vehicle speed indicated on the combination meter exceeds
15km/h (10 MPH).
POSSIBLE CAUSE
Harness or connectors (CAN communication line is open or shorted.)
Combination meter
ABS actuator and electric unit (control unit)
Wheel sensor
TCM
Output speed sensor
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0500 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
>> GO TO 3.
Start engine.
Shift the selector lever to D range and wait at least for 2 seconds.
Drive the vehicle at least 5 seconds at 20 km/h (13 MPH) or more.
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
Check 1st trip DTC.
Revision: August 2014
EC-353
3.PERFORM DTC CONFIRMATION PROCEDURE
4.
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.
1.
2.
3.
2015 Rogue NAM
P0500 VSS
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is 1st trip DTC detected?
YES >> Proceed to EC-354, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278062
1.CHECK DTC PRIORITY
If DTC P0500 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-63, "DTC Index".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Perform trouble shooting relevant to DTC indicated.
3.CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit). Refer to BRC-53, "DTC Index".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Perform trouble shooting relevant to DTC indicated.
4.CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to MWI-31, "DTC Index".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Perform trouble shooting relevant to DTC indicated.
5.CHECK INPUT SPEED SENSOR
Check input speed sensor. Refer to TM-125, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace or replace error-detected parts.
6.CHECK WHEEL SENSOR
Check wheel sensor. Refer to BRC-72, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace or replace error-detected parts.
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-354
2015 Rogue NAM
P0506 ISC SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0506 ISC SYSTEM
Description
INFOID:0000000011278063
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let EC
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value C
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan D
operation, etc.).
DTC Description
INFOID:0000000011278064
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
ISC SYSTEM
(Idle air control system RPM lower than expected)
P0506
DTC detecting condition
The idle speed is less than the target idle speed by 100 rpm or more.
POSSIBLE CAUSE
Electric throttle control actuator
Intake air leak
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
If the target idle speed is out of the specified value, perform EC-144, "Work Procedure", before conducting DTC Confirmation Procedure.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above 10C (14F).
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and run it for at least 1 minute at idle speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-356, "Diagnosis Procedure".
Revision: August 2014
EC-355
2015 Rogue NAM
P0506 ISC SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278065
1.CHECK DTC PRIORITY
If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK INTAKE AIR LEAK
1. Start engine and let it idle.
2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES >> Discover air leak location and repair.
NO
>> Replace ECM. Refer to EC-502, "Removal and Installation".
Revision: August 2014
EC-356
2015 Rogue NAM
P0507 ISC SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0507 ISC SYSTEM
Description
INFOID:0000000011278066
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let EC
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value C
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan D
operation, etc.).
DTC Description
INFOID:0000000011278067
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
ISC SYSTEM
(Idle air control system RPM higher than expected)
P0507
DTC detecting condition
The idle speed is more than the target idle speed by 200 rpm or more.
POSSIBLE CAUSE
Electric throttle control actuator
Intake air leak
PCV system
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
If the target idle speed is out of the specified value, perform EC-144, "Work Procedure", before conducting DTC Confirmation Procedure.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above 10C (14F).
>> GO TO 3.
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and run it for at least 1 minute at idle speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
EC-357
3.PERFORM DTC CONFIRMATION PROCEDURE
Revision: August 2014
2015 Rogue NAM
P0507 ISC SYSTEM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> Proceed to EC-358, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278068
1.CHECK DTC PRIORITY
If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK PCV HOSE CONNECTION
Confirm that PCV hose is connected correctly.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK INTAKE AIR LEAK
1. Start engine and let it idle.
2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES >> Discover air leak location and repair.
NO
>> Replace ECM. Refer to EC-502, "Removal and Installation".
Revision: August 2014
EC-358
2015 Rogue NAM
P050A, P050B, P050E COLD START CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P050A, P050B, P050E COLD START CONTROL
Description
A
INFOID:0000000011278069
ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.
This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.
DTC Description
EC
INFOID:0000000011278070
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P050A
COLD START CONTROL
(Cold start idle air control system performance)
ECM does not control engine idle speed properly when engine is started
with pre-warming up condition.
P050B
COLD START CONTROL
(Cold start ignition timing performance)
ECM does not control ignition timing properly when engine is started with
pre-warming up condition.
P050E
COLD START CONTROL
(Cold start engine exhaust temperature too
low)
The temperature of the catalyst inlet does not rise to the proper temperature when the engine is started with pre-warming up condition.
POSSIBLE CAUSE
Lack of intake air volume
Fuel injection system
ECM
FAIL-SAFE
I
P050A
Traveling control mode (Accelerator angle variation control)
P050B, P050E
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P050A, P050B or P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 3.
With CONSULT
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Check the indication of COOLAN TEMP/S.
With GST
Revision: August 2014
EC-359
3.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
2.
3.
4.
2015 Rogue NAM
P050A, P050B, P050E COLD START CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Follow the procedure With CONSULT above.
Is the value of COOLAN TEMP/S between 15C (59F) and 36C (97F)?
YES >> GO TO 4.
NO-1 [If it is below 15C (59F)]>>Warm up the engine until the value of COOLAN TEMP/S reaches 15C
(59F) or more. Retry from step 1.
NO-2 [If it is above 36C (97F)]>>Cool engine down to less than 36C (97F). Retry from step 1.
4.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
Set the select lever in N range.
Start the engine and warm up in idle with the value of COOLAN TEMP/S between 15C (59F) and 40C
(104F) for more than 15 seconds.
3. Check 1st trip DTC.
With GST
Follow the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-360, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
Diagnosis Procedure
INFOID:0000000011278071
1.CHECK DTC PRIORITY
If DTC P050A, P050B or P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-144, "Work Procedure".
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 3.
NO
>> Follow the instruction of Idle Air Volume Learning.
3.CHECK INTAKE SYSTEM
Check for the cause of intake air volume lacking. Refer to the following.
Crushed intake air passage
Intake air passage clogging
Clogging of throttle body
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace malfunctioning part
4.CHECK FUEL INJECTION SYSTEM FUNCTION
Perform DTC Confirmation Procedure for DTC P0171. Refer to EC-263, "DTC Description".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Proceed to EC-264, "Diagnosis Procedure" for DTC P0171.
5.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
3.
Turn ignition switch ON.
Erase DTC.
Perform DTC Confirmation Procedure.
See EC-359, "DTC Description".
Is the 1st trip DTC P050A, P050B or P050E displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-360
2015 Rogue NAM
P0520 EOP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0520 EOP SENSOR
DTC Description
INFOID:0000000011278072
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
EOP SENSOR/SWITCH
(Engine oil pressure sensor/switch circuit)
P0520
DTC detecting condition
Signal voltage from the EOP sensor remains at more than 5.02 V / less than
0.3 V for 5 seconds or more.
POSSIBLE CAUSE
Harness or connectors (EOP sensor circuit is open or shorted.)
Engine oil level abnormality
EOP sensor
Sensor power supply 2 circuit
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-361, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278073
1.CHECK ENGINE OIL
M
1. Turn ignition switch OFF.
2. Check engine oil level and pressure. Refer to LU-7, "Inspection".
Is inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.CHECK EOP SENSOR POWER SUPPLY-1
1.
2.
3.
Disconnect EOP sensor connector.
Turn ignition switch ON.
Check the voltage between EOP sensor harness connector terminals.
EOP sensor
Connector
F54
Voltage
(Approx.)
5V
terminal
3
Inspection result normal?
Revision: August 2014
EC-361
2015 Rogue NAM
P0520 EOP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 7.
NO
>> GO TO 3.
3.CHECK EOP SENSOR POWER SUPPLY-2
Check the voltage between EOP sensor harness connector and the ground.
+
Voltage
(Approx.)
Ground
5V
EOP sensor
Connector
Terminal
F54
Is inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Is inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
5.CHECK EOP SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EOP sensor harness connector and ECM harness connector.
+
EOP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F54
F51
38
Existed
4. Also check harness for short to power.
Is inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK ECM GROUND CIRCUIT
Check the continuity between ECM harness connector and ground.
+
ECM
Connector
Terminal
F51
16
F52
52
E16
123
Continuity
Ground
Existed
128
Is inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
7.CHECK EOP SENSOR SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EOP sensor harness connector and ECM harness connector.
Revision: August 2014
EC-362
2015 Rogue NAM
P0520 EOP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
EOP sensor
ECM
A
Continuity
Connector
Terminal
Connector
Terminal
F54
F51
39
EC
Existed
4. Also check harness for short to ground and to power.
Is inspection result normal?
YES >> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.CHECK EOP SENSOR
Refer to EC-363, "Component Inspection".
Is inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
G
>> INSPECTION END
Component Inspection
INFOID:0000000011278074
1.CHECK EOP SENSOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect EOP sensor harness connector.
Check resistance between EOP sensor connector terminals.
EOP sensor
Condition
Resistance (k)
Terminal
1
4 k 10 k
2 k 8 k
1
3
4 k 10 k
None
1 k 3 k
2 k 8 k
1 k 3 k
Is the inspection result normal?
YES >> INSPECTION END.
NO
>> Replace EOP sensor. Refer to EC-14, "Component Parts Location".
Revision: August 2014
EC-363
2015 Rogue NAM
P0524 ENGINE OIL PRESSURE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0524 ENGINE OIL PRESSURE
DTC Description
INFOID:0000000011278075
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0524
ENGINE OIL PRESSURE
(Engine oil pressure too low)
DTC detecting condition
An EOP sensor signal voltage applied to ECM remains lower than the specified value continuously for 10 seconds or more when the engine speed is
1,000 rpm or more.
POSSIBLE CAUSE
Decrease in engine oil pressure
Decrease in engine oil level
Engine oil condition
EOP sensor
Engine body
FAIL-SAFE
ECM illuminates oil pressure warning lamp on the combination meter.
Engine speed will not rise more than 4,000rpm due to the fuel cut.
Fail-safe is canceled when ignition switch OFF ON.
DTC CONFIRMATION PROCEDURE
CAUTION:
If EC-365, "Diagnosis Procedure" is unfinished, be sure to perform Step 3 and 4.
1.PRECONDITIONING-1
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TEST CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 2.
2.PRECONDITIONING-2
Is Diagnosis Procedure of DTC P0524 finished?
YES >> GO TO 3.
NO
>> GO TO 4.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
Start engine and warm it up to normal operating temperature.
Maintain the following conditions for about 10 consecutive seconds.
Selector lever
P or N position
Engine coolant temperature
70C (158F) or more
Engine speed
1,000 rpm or more
NOTE:
With engine speed set around 4,000 rpm, the phenomenon can be reproduced more easily.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-365, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-364
2015 Rogue NAM
P0524 ENGINE OIL PRESSURE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4.CHECK ENGINE OIL LEVEL
Check engine oil pressure. Refer to LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Proceed to EC-365, "Diagnosis Procedure".
EC
5.CHECK ENGINE OIL PRESSURE
With CONSULT
1. Turn ignition switch ON.
2. Select DATA MONITOR mode of ENGINE using CONSULT.
3. Start the engine and check that EOP SENSOR changes, according to engine speeds.
Monitor item
EOP SENSOR
Value
(Approx.)
Condition
Engine oil temperature: 80C (176F)
Selector lever: P or N position
Air conditioner switch: OFF
No load
Engine speed:
Idle
1,450 mV or more
Engine speed:
2,000 rpm
2,850 mV or more
Without CONSULT
Check engine oil level. Refer to LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Proceed to EC-365, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278076
1.CHECK ENGINE OIL LEVEL
1. Turn ignition switch OFF.
2. Check engine oil pressure level. Refer to LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> GO TO 4.
2.CHECK ENGINE OIL PRESSURE
1.
2.
3.
With CONSULT
Turn ignition switch ON.
Select DATA MONITOR mode of ENGINE using CONSULT.
Start the engine and check that EOP SENSOR changes, according to engine speeds.
Monitor item
EOP SENSOR
Value
(Approx.)
Condition
Engine oil temperature: 80C (176F)
Selector lever: P or N position
Air conditioner switch: OFF
No load
Engine speed:
Idle
1,450 mV or more
Engine speed:
2,000 rpm
2,850 mV or more
Without CONSULT
Check engine oil pressure. Refer to LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Check oil pump. Refer to LU-15, "Inspection".
3.CHECK EOP SENSOR
Check EOP sensor. Refer to EC-363, "Component Inspection".
Is the inspection result normal?
Revision: August 2014
EC-365
2015 Rogue NAM
P0524 ENGINE OIL PRESSURE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
4.CHECK ENGINE OIL LEAKAGE
Check engine oil leakage. Refer to LU-6, "Engine Lubrication System Schematic".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK CAUSE OF ENGINE OIL CONSUMPTION
Check the following item.
Step
Inspection item
Equipment
Standard
Reference
PCV valve
EC-501, "Inspection"
Exhaust front tube
Visual
No blocking
No abnormal sounds
Oil pump
Visual
No blocking
No abnormal sounds
LU-15, "Inspection"
4
Piston
Piston pin
Piston ring
Piston to piston pin oil clearance
Piston ring side clearance
Piston ring end gap
Cylinder block
Cylinder block top surface distortion
Piston to cylinder bore clearance
EM-114, "How to Select
Piston and Bearing"
EM-105, "Inspection"
>> Repair or replace error-detected parts.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278077
1.CHECK EOP SENSOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect EOP sensor harness connector.
Check resistance between EOP sensor connector terminals.
EOP sensor
Condition
Resistance (k)
Terminal
1
4 k 10 k
2 k 8 k
1
3
4 k 10 k
None
1 k 3 k
2 k 8 k
1 k 3 k
Is the inspection result normal?
YES >> INSPECTION END.
NO
>> Replace EOP sensor. Refer to EC-14, "Component Parts Location".
Revision: August 2014
EC-366
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P052A, P052B INTAKE VALVE TIMING CONTROL
DTC Description
A
INFOID:0000000011278078
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P052A
CAMSHAFT POSITION TIMING B1
(Cold start A camshaft position timing
over-advanced bank 1)
P052B
CAMSHAFT POSITION TIMING B1
(Cold start A camshaft position timing
over-retarded bank 1)
DTC detecting condition
There is a gap between angle of target and phase-control angle degree
when the engine is in a cold condition.
POSSIBLE CAUSE
Crankshaft position sensor
Camshaft position sensor
Intake valve timing control solenoid valve
Intake valve timing intermediate lock control solenoid valve
Accumulation of debris to the signal pick-up portion of the camshaft
Timing chain installation
Foreign matter caught in the oil groove for intake valve timing control
FAIL-SAFE
Device fix mode
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P052A or P052B is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-194, "DTC Description".
NO
>> GO TO 2.
2.PRECONDITIONING
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. On the CONSULT screen, select ENGINE >> DATA MONITOR >> COOLAN TEMP/S.
6. Check COOLAN TEMP/S indication value.
With GST
Follow the procedure With CONSULT above.
Is the value of COOLAN TEMP/S5C (23F) and 45C (113F)?
YES >> GO TO 3.
NO-1 [if it is below 5C (23F)]>>Warm up the engine until the value of COOLAN TEMP/S indicates 5C
(23F) and 45C (113F). And then GO TO 3.
NO-2 [if it is above 45C (113F)]>>Cool the engine down to the value of COOLAN TEMP/S indicates 5C
(23F) and 45C (113F). And then GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-I
1.
2.
3.
4.
5.
Turn ignition switch OFF and wait at 10 seconds.
Turn ignition switch ON.
Set the selector lever in N range.
Start the engine and let it idle for 20 seconds or more.
Check 1st trip DTC.
Revision: August 2014
EC-367
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is 1st trip DTC detected?
YES >> Proceed to EC-368, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278079
1.CHECK DTC PRIORITY
If DTC P052A or P052B is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-194, "DTC Description".
NO
>> GO TO 2.
2.INSPECTION START
With CONSULT>>GO TO 3.
Without CONSULT>>GO TO 4.
3.CHECK VTC POSITION
1.
2.
3.
4.
5.
6.
With CONSULT
Turn ignition switch ON.
On the CONSULT screen, select ENGINE >> DATA MONITOR >> COOLAN TEMP/S.
Check that the COOLAN TEMP/S indication value is between 5C (23F) and 45C (113F).
Start engine and wait at least 5 seconds.
On the CONSULT screen, select ENGINE >> DATA MONITOR >> INT/V TIM (B1).
Check that the data monitor item indicates as follows:
Item
Value (CA)
INT/V TIM (B1)
10 2
Is the inspection result normal?
YES >> GO TO 12.
NO
>> GO TO 4.
4.CHECK OIL PRESSURE WARNING LAMP
1. Start engine.
2. Check that oil pressure warning lamp is not illuminated.
Is oil pressure warning lamp illuminated?
YES >> Refer to LU-7, "Inspection".
NO
>> GO TO 5.
5.CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE
PBIA8559J
Perform Component Inspection of the intake valve timing intermediate lock control solenoid valve. Refer to
EC-370, "Component Inspection (Intake Valve Timing Intermediate Lock Control Solenoid Valve)".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Perform Component Inspection of the intake valve timing control solenoid valve. Refer to EC-369, "Component Inspection (Intake Valve Timing Control Solenoid Valve)".
Revision: August 2014
EC-368
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
[QR25DE]
A
7.CHECK CRANKSHAFT POSITION SENSOR
Perform Component Inspection of the crankshaft position sensor. Refer to EC-371, "Component Inspection
(Crankshaft Position sensor)".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.CHECK CAMSHAFT POSITION SENSOR
EC
Perform Component Inspection of the camshaft position sensor. Refer to EC-371, "Component Inspection
(Camshaft position sensor)".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.CHECK CAMSHAFT (INTAKE)
Check the following.
1. Accumulation of debris on the signal plate of camshaft front end
2. Chipping signal plate of camshaft front end
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Remove debris and clean the signal plate of camshaft
front end or replace camshaft. Refer to EM-69,
"Removal and Installation".
JPBIA5855ZZ
10.CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misalignment.
Are there any service records that may cause timing chain misalignment?
YES >> Check timing chain installation. Refer to EM-50, "Removal and Installation".
NO
>> GO TO 11.
11.CHECK LUBRICATION CIRCUIT
Perform Inspection of Camshaft Sprocket (INT) Oil Groove. Refer to EM-77, "Inspection After Installation".
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Clean lubrication line.
12.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
O
>> INSPECTION END
Component Inspection (Intake Valve Timing Control Solenoid Valve)
INFOID:0000000011278080
1.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake valve timing control solenoid valve harness connector.
Check resistance between intake valve timing control solenoid valve terminals as per the following.
Revision: August 2014
EC-369
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Terminals
Resistance
1 and 2
7.0 - 7.7 [at 20C (68F)]
1 or 2 and ground
(Continuity should not exist)
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace malfunctioning intake valve timing control solenoid valve. Refer to EM-49, "Exploded
View".
2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II
Remove intake valve timing control solenoid valve. Refer to EM-49, "Exploded View".
Provide 12 V DC between intake valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Check that the
plunger moves as shown in the figure.
CAUTION:
Never apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing control
solenoid valve is removed.
Is the inspection result normal?
JMBIA2107ZZ
YES >> INSPECTION END
NO
>> Replace malfunctioning intake valve timing control solenoid valve. Refer to EM-49, "Exploded
View".
1.
2.
Component Inspection (Intake Valve Timing Intermediate Lock Control Solenoid Valve)
INFOID:0000000011278081
1.CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-I
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake valve timing intermediate lock control solenoid valve harness connector.
Check resistance between intake valve timing intermediate lock control solenoid valve terminals as per
the following.
Terminals
Resistance
1 and 2
7.0 - 7.7 [at 20C (68F)]
1 or 2 and ground
(Continuity should not exist)
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace malfunctioning intake valve timing intermediate lock control solenoid valve. Refer to EM49, "Exploded View".
2.CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-II
1.
Remove intake valve timing intermediate lock control solenoid valve. Refer to EM-49, "Exploded View".
Revision: August 2014
EC-370
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Provide 12 V DC between intake valve timing intermediate lock
control solenoid valve terminals 1 and 2, and then interrupt it.
A
Check that the plunger moves as shown in the figure.
CAUTION:
Never apply 12 V DC continuously for 5 seconds or more.
EC
Doing so may result in damage to the coil in intake valve
timing intermediate lock control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing intermediC
ate lock control solenoid valve is removed.
Is the inspection result normal?
JMBIA2107ZZ
D
YES >> INSPECTION END
NO
>> Replace malfunctioning intake valve timing intermediate lock control solenoid valve. Refer to EM49, "Exploded View".
Component Inspection (Crankshaft Position sensor)
INFOID:0000000011278082
1.CHECK CRANKSHAFT POSITION SENSOR (POS)-1
1. Turn ignition switch OFF.
2. Loosen the fixing bolt of the sensor.
3. Disconnect crankshaft position sensor (POS) harness connector.
4. Remove the sensor.
5. Visually check the sensor for chipping.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace crankshaft position sensor (POS). Refer to EM97, "Exploded View".
J
PBIA9209J
2.CHECK CRANKSHAFT POSITION SENSOR (POS)-2
Check the resistance between crankshaft position sensor (POS) terminals as per the following.
Crankshaft position sensor (POS)
L
Resistance [at 25C (77F)]
Terminal (Polarity)
1
2
2
3
Except 0 or
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace crankshaft position sensor (POS). Refer to EM-97, "Exploded View".
Component Inspection (Camshaft position sensor)
O
INFOID:0000000011278083
1.CHECK CAMSHAFT POSITION SENSOR (PHASE)-1
1.
2.
3.
4.
Turn ignition switch OFF.
Loosen the fixing bolt of the sensor.
Disconnect camshaft position sensor (PHASE) harness connector.
Remove the sensor.
Revision: August 2014
EC-371
2015 Rogue NAM
P052A, P052B INTAKE VALVE TIMING CONTROL
< DTC/CIRCUIT DIAGNOSIS >
5. Visually check the sensor for chipping.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace camshaft position sensor (PHASE).
2.CHECK CAMSHAFT POSITION SENSOR (PHASE)-2
[QR25DE]
PBIA9876J
Check the resistance camshaft position sensor (PHASE) terminals as per the following.
Camshaft position sensor (PHASE)
Resistance [ at 25C (77F)]
Terminals (Polarity)
1
2
2
3
Except 0 or
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace camshaft position sensor (PHASE). Refer to EM-69, "Removal and Installation".
Revision: August 2014
EC-372
2015 Rogue NAM
P0603, P062F ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0603, P062F ECM
DTC Description
INFOID:0000000011278084
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P0603
ECM BACK UP/CIRCUIT
[Internal Control Module Keep Alive Memory (KAM) Error]
ECM buck up system does not function properly.
P062F
CONTROL MODULE
(Internal control module EEPROM error)
EEPROM (built-in microcomputer) system internal ECM does not function
properly.
POSSIBLE CAUSE
DTC P0603
Harness or connectors (ECM power supply circuit is open or shorted.)
ECM
DTC P062F
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
Perform the following procedure before performing DTC Confirmation Procedure.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
1.PRECONDITIONING
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P062F
1. Start engine and wait at least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Repeat steps 1 and 2 for 4 times.
4. Turn ignition switch ON.
5. Erase DTC.
6. Turn ignition switch OFF and wait at least 10 seconds.
7. Start engine and wait at least 10 seconds.
8. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-374, "Diagnosis Procedure".
NO
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0603
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON and wait at least 10 seconds.
3. Turn ignition switch OFF and wait at least 5 minutes.
4. Turn ignition switch ON and wait at least 10 seconds.
5. Repeat steps 3 and 4 for 5 times.
6. Turn ignition switch ON.
7. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-374, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-373
2015 Rogue NAM
P0603, P062F ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278085
1.INSPECTION START
Check that the battery negative terminal is not disconnected during ignition switch ON.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.ERASE DTC
1. Start the engine and let it idle at least 10 seconds.
2. Turn ignition switch OFF.
3. Repeat steps 1 and 2 for 4 times.
4. Erase DTC.
5. Turn ignition switch OFF and wait at least 10 seconds.
6. Start the engine and let it idle for 10 seconds.
7. Check 1st trip DTC.
Is DTC P062F detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
3.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT
Check ECM power supply and ground circuit. Refer to EC-168, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-373, "DTC Description".
Is the DTC P0603 or P062F detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-374
2015 Rogue NAM
P0604 ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0604 ECM
DTC Description
INFOID:0000000011278086
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
ECM
[Internal control module random access
memory (RAM) error]
P0604
EC
DTC detecting condition
Malfunction in the internal RAM of ECM.
POSSIBLE CAUSE
ECM
E
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON (engine stopped) and wait least 20 minutes.
CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-375, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278087
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-375, "DTC Description".
Is the 1st trip DTC P0604 displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-375
2015 Rogue NAM
P0605 ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0605 ECM
DTC Description
INFOID:0000000011278088
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P0605
ECM
[Internal control module read only memory
(ROM) error]
DTC detecting condition
Malfunction in the internal ROM of ECM.
POSSIBLE CAUSE
ECM
FAIL-SAFE
Traveling control mode (Engine output control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON (engine stopped) and wait least 20 minutes.
CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-376, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278089
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-375, "DTC Description".
Is the 1st trip DTC P0605 displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-376
2015 Rogue NAM
P0606 ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0606 ECM
DTC Description
INFOID:0000000011278090
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
CONTROL MODULE
(Control module processor)
P0606
EC
DTC detecting condition
Malfunction in ECM processor.
POSSIBLE CAUSE
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE-I
1.
Turn ignition switch ON (engine stopped) and wait at least 10 seconds.
CAUTION:
Never start engine during this procedure.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-377, "Diagnosis Procedure".
NO
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-II
1.
2.
Start engine.
Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release
the accelerator pedal.
3. Let the engine idle and wait at least 10 seconds.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Turn ignition switch ON.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-377, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
P
INFOID:0000000011278091
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure for 3 times. Refer to EC-377, "DTC Description".
Is the 1st trip DTC P0606 displayed again?
Revision: August 2014
EC-377
2015 Rogue NAM
P0606 ECM
< DTC/CIRCUIT DIAGNOSIS >
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-378
[QR25DE]
2015 Rogue NAM
P0607 ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0607 ECM
DTC Description
INFOID:0000000011278092
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
ECM
(Control module performance)
P0607
EC
DTC detecting condition
ECM internal communication system is malfunctioning.
POSSIBLE CAUSE
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-379, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278093
1.PERFORM DTC CONFIRMATION PROCEDURE
M
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-375, "DTC Description".
Is the 1st trip DTC P0607 displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-379
2015 Rogue NAM
P060A ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P060A ECM
DTC Description
INFOID:0000000011278094
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P060A
CONTROL MODULE
(Internal control module monitoring processor performance)
DTC detecting condition
ECM internal monitoring processor is malfunctioning.
POSSIBLE CAUSE
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait at least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Repeat step 1 and 2 for 5 times.
4. Turn ignition switch ON.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-380, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278095
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-380, "DTC Description".
Is the 1st trip DTC P060A displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-380
2015 Rogue NAM
P060B ECM
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P060B ECM
DTC Description
INFOID:0000000011278096
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
CONTROL MODULE
(Internal control module A/D processing
performance)
P060B
EC
DTC detecting condition
ECM internal analog/digital conversion processing system is malfunctioning.
POSSIBLE CAUSE
ECM
E
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition
switch ON.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-381, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
L
INFOID:0000000011278097
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure. Refer to EC-381, "DTC Description".
Is the 1st trip DTC P060B displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-381
2015 Rogue NAM
P0643 SENSOR POWER SUPPLY
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0643 SENSOR POWER SUPPLY
Description
INFOID:0000000011278098
ECM supplies a voltage of 5 V to some of the sensors systematically divided into 2 groups, respectively.
Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously
in the sensors belonging to the same group as the short-circuited sensor.
Sensor power supply 1
APP sensor 1
CKP sensor (POS)
Intake manifold runner control valve position sensor
Refrigerant pressure sensor
TP sensor
NOTE:
If sensor power supply 1 circuit is malfunctioning, DTC P0643 is displayed.
Sensor power supply 2
APP sensor 2
CMP sensor (PHASE)
EVT control position sensor
EOP sensor
MAF sensor
DTC Description
INFOID:0000000011278099
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
SENSOR POWER/CIRC
(Sensor reference voltage A circuit high)
ECM detects that the voltage of sensor power supply 1 is excessively low
or high.
DTC No.
P0643
POSSIBLE CAUSE
Harness or connectors
APP sensor 1 circuit is shorted.
CKP sensor (POS) circuit is shorted.
Intake manifold runner control valve position sensor circuit is shorted.
TP sensor circuit is shorted.
Refrigerant pressure sensor circuit is shorted.
Accelerator pedal position sensor
CKP sensor (POS)
Intake manifold runner control valve position sensor
Throttle position sensor
Refrigerant pressure sensor
FAIL-SAFE
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx.
5 degrees) by the return spring.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
Revision: August 2014
EC-382
2015 Rogue NAM
P0643 SENSOR POWER SUPPLY
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Refer to EC-383, "Diagnosis Procedure".
NO
>> INSPECTION END
EC
Diagnosis Procedure
INFOID:0000000011278100
1.CHECK GROUND CONNECTION
1. Turn ignition switch OFF.
2. Check ground connection E9 and E15. Refer to Ground Inspection in GI-46, "Circuit Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace ground connection.
2.CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.
+
-
Voltage
(Approx.)
Ground
5V
APP sensor
Connector
Terminal
E25
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 3.
3.CHECK SENSOR POWER SUPPLY CIRCUITS
Check harness for short to power and short to ground, between the following terminals.
ECM
Connector
F52
E16
Sensor
Terminal
Name
Connector
Terminal
72
CKP sensor (POS)
F17
80
Electric throttle control actuator
F50
84
Intake manifold runner control valve position sensor
F20
104
Refrigerant pressure sensor
F10
122
APP sensor
E25
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair short to ground or short to power in harness or connectors.
4.CHECK COMPONENTS
Check the following.
Crankshaft position sensor (POS) (Refer to EC-300, "Component Inspection (Crankshaft Position sensor)".)
Intake manifold runner control valve position sensor (Refer to EC-427, "Diagnosis Procedure".)
Refrigerant pressure sensor (Refer to EC-485, "Diagnosis Procedure".)
TP sensor (Refer to EC-221, "Component Inspection".)
Is the inspection result normal?
YES >> GO TO 5.
Revision: August 2014
EC-383
2015 Rogue NAM
P0643 SENSOR POWER SUPPLY
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> Repair or replace malfunctioning component.
5.CHECK APP SENSOR
Refer to EC-445, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
6.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-384
2015 Rogue NAM
P0850 PNP SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P0850 PNP SWITCH
Description
INFOID:0000000011278101
Transmission range switch is turn ON when the selector lever is P or N.
ECM detects the position because the continuity of the line (the ON) exists.
DTC Description
EC
INFOID:0000000011278102
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P-N POS SW/CIRCUIT
(Park/neutral switch input circuit)
P0850
DTC detecting condition
The signal of transmission range switch is not changed in the process of
engine starting and driving.
POSSIBLE CAUSE
Harness or connectors (The transmission range switch circuit is open or shorted.)
Transmission range switch
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO
>> GO TO 5.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
With CONSULT
Turn ignition switch ON.
Select P/N POSI SW in DATA MONITOR mode of ENGINE using CONSULT. Then check the P/N
POSI SW signal as per the following conditions.
Selector lever position
ON
Except above position
OFF
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Proceed to EC-386, "Diagnosis Procedure".
4.PERFORM DTC CONFIRMATION PROCEDURE
Select DATA MONITOR mode of ENGINE using CONSULT.
Start engine and warm it up to normal operating temperature.
Maintain the following conditions for at least 60 consecutive seconds.
CAUTION:
Revision: August 2014
Known-good signal
N or P position
1.
2.
3.
3.CHECK PNP SIGNAL FUNCTION
1.
2.
EC-385
2015 Rogue NAM
P0850 PNP SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Always drive vehicle at a safe speed.
ENG SPEED
1,000 - 6,375 rpm
COOLAN TEMP/S
More than 65C (149F)
B/FUEL SCHDL
3.25 - 31.8 msec
VHCL SPEED SE
More than 64 km/h (40 mph)
Selector lever
Suitable position
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-386, "Diagnosis Procedure".
NO
>> INSPECTION END
5.PERFORM COMPONENT FUNCTION CHECK
1.
2.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following conditions.
ECM
Connector
Condition
Voltage
(Approx.)
Terminal
E16
117
128
Selector lever
P or N
Battery voltage
Except above
0V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-386, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278103
1.CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect transmission range switch harness connector.
Turn ignition switch ON.
Check the voltage between transmission range switch harness connector and ground.
+
Voltage
Ground
Battery voltage
Transmission range switch
Connector
Terminal
F78
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between transmission range switch harness connector and IPDM E/R harness connector.
+
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F78
F35
70
Revision: August 2014
Existed
EC-386
2015 Rogue NAM
P0850 PNP SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK TRANSMISSION RANGE SWITCH SIGNAL CIRCUIT
1.
2.
3.
EC
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between transmission range switch harness connector and ECM harness connector.
+
Transmission range switch
ECM
D
Continuity
Connector
Terminal
Connector
Terminal
F78
10
E16
117
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK TRANSMISSION RANGE SWITCH
Check the transmission range switch. Refer to TM-110, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace transmission range switch. Refer to TM-220, "Removal and Installation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-387
2015 Rogue NAM
P1078 EVT CONTROL POSITION SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1078 EVT CONTROL POSITION SENSOR
DTC Description
INFOID:0000000011278104
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
EXH TIM SEN/CIRC-B1
(EXH TIM SEN/CIRC-B1)
P1078
DTC detecting condition
An excessively high or low voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (Exhaust valve timing control position sensor circuit is open or shorted.)
Accumulation of debris to the signal pick-up portion of the camshaft
Exhaust valve timing control position sensor
Sensor power supply 2 circuit
FAIL-SAFE
Traveling control mode (Accelerator angle variation control)
Device fix mode
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-388, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278105
1.CHECK EXHAUST VALVE TIMING (EVT) CONTROL POSITION SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect exhaust valve timing (EVT) control position sensor harness connector.
Turn ignition switch ON.
Check the voltage between EVT control position sensor harness connector and ground.
+
EVT control position sensor
Connector
Terminal
F45
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Revision: August 2014
EC-388
2015 Rogue NAM
P1078 EVT CONTROL POSITION SENSOR
< DTC/CIRCUIT DIAGNOSIS >
Is inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
[QR25DE]
A
3.CHECK EVT CONTROL POSITION SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between EVT control position sensor harness connector and ECM harness connector.
+
EVT control position sensor
ECM
Terminal
Connector
Terminal
F45
F51
42
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK EVT CONTROL POSITION SENSOR INPUT SIGNAL CIRCUIT
1.
2.
Disconnect ECM harness connector.
Check the continuity between EVT control position sensor harness connector and ECM harness connector.
+
EVT control position sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F45
F51
43
Continuity
Connector
EC
Existed
3. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK EVT CONTROL POSITION SENSOR
Check the EVT control position sensor. Refer to EC-390, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace EVT control position sensor. Refer to EM-69, "Exploded View".
6.CHECK CAMSHAFT (EXT)
Check the following.
Accumulation of debris to the signal plate of camshaft rear end
Chipping signal plate of camshaft rear end
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft. Refer to EM-69, "Removal
and Installation".
JPBIA5856ZZ
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
Revision: August 2014
EC-389
2015 Rogue NAM
P1078 EVT CONTROL POSITION SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> INSPECTION END
Component Inspection
INFOID:0000000011278106
1.EXHAUST VALVE TIMING (EVT) CONTROL POSITION SENSOR-1
1. Turn ignition switch OFF.
2. Disconnect EVT control position sensor harness connector.
3. Loosen the fixing bolt of the sensor.
4. Remove the sensor.
5. Visually check the sensor for chipping.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace EVT control position sensor. Refer to EM-69,
"Exploded View".
JMBIA0065ZZ
2.EVT CONTROL POSITION SENSOR-2
Check resistance EVT control position sensor terminals as shown below.
EVT control position sensor
Resistance
Terminal
1
2
2
3
Except 0 or [at 25C (77F)]
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace EVT control position sensor. Refer to EM-69, "Exploded View".
Revision: August 2014
EC-390
2015 Rogue NAM
P1148 CLOSED LOOP CONTROL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1148 CLOSED LOOP CONTROL
DTC Description
INFOID:0000000011278107
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P1148
EC
CLOSED LOOP-B1
(CLOSED LOOP-B1)
DTC detecting condition
The closed loop control function does not operate even when vehicle is being driven in the specified condition.
POSSIBLE CAUSE
Harness or connectors (A/F sensor 1 circuit is open or shorted.)
A/F sensor 1
A/F sensor 1 heater
FAIL-SAFE
Not applicable
Diagnosis Procedure
INFOID:0000000011278108
DTC P1148 is displayed with DTC for A/F sensor 1.
When the DTC is detected, perform the trouble diagnosis of DTC corresponding to A/F sensor 1.
Refer to EC-96, "DTC Index".
Revision: August 2014
EC-391
2015 Rogue NAM
P117A AIR FUEL RATIO
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P117A AIR FUEL RATIO
DTC Description
INFOID:0000000011278109
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P117A
AIR FUEL RATIO B1
(AIR FUEL RATIO B1)
DTC detecting condition
ECM detects a lean/rich air fuel ratio state in any cylinder for a specified
length of time.
POSSIBLE CAUSE
Fuel injector
Exhaust gas leaks
Incorrect fuel pressure
Mass air flow sensor
Intake air leaks
Lack of fuel
Incorrect PCV hose connection
Improper spark plug
Insufficient compression
The fuel injector circuit is open or shorted
Ignition coil
The ignition signal circuit is open or shorted
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P117A is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING-1
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
NOTE:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 3.
3.PRECONDITIONING-2
1. Turn ignition switch ON.
2. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
Will CONSULT be used?
YES >> GO TO 4.
NO
>> GO TO 7.
4.PERFORM DTC CONFIRMATION PROCEDURE-1
1.
2.
3.
4.
Turn ignition switch ON.
Select COOLAN TEMP/S in DATA MONITOR mode of ENGINE using CONSULT.
Start engine.
Make sure that COOLAN TEMP/S indicates more than 80C (176F).
Revision: August 2014
EC-392
2015 Rogue NAM
P117A AIR FUEL RATIO
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
EC
Select SYSTEM 1 DIAGNOSIS B B1 and SYSTEM 1 DIAGNOSIS A B1 in DATA MONITOR mode of
ENGINE using CONSULT.
2. Drive vehicle under the following conditions for at least 5 consecutive seconds.
C
CAUTION:
Always drive vehicle at a safe speed.
1.
ENG SPEED
1,300 2,000rpm
COOLAN TEMP/S
More than 80C (176F)
B/FUEL SCHDL
4 8 msec
Selector lever
D position
SYSTEM 1 DIAGNOSIS B B1
PRSENT
NOTE:
Drive the vehicle at approximately 88 km/h (55MPH) allows easy diagnosis.
Keep the accelerator pedal as possible during crusing.
3. Check SYSTEM 1 DIAGNOSIS A B1 indication.
Is CMPLT displayed?
YES >> GO TO 6.
NO
>> GO TO 3.
6.PERFORM DTC CONFIRMATION PROCEDURE-3
Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-393, "Diagnosis Procedure".
NO
>> INSPECTION END
7.PERFORM DTC CONFIRMATION PROCEDURE-4
1.
2.
Without CONSULT
Start the engine and warm it up to normal operating temperature.
Drive vehicle under the following conditions for at least 5 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
Engine speed
1,000 1,250 rpm
Calculated load value
26 46 %
Selector lever
D position
NOTE:
Drive the vehicle at approximately 88 km/h (55MPH) allows easy diagnosis.
Keep the accelerator pedal as possible during crusing.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-393, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278110
1.CHECK DTC PRIORITY
If DTC P117A is displayed with other DTC, first perform the trouble diagnosis for other DTC.
Is applicable DTC detected?
Revision: August 2014
EC-393
2015 Rogue NAM
P117A AIR FUEL RATIO
< DTC/CIRCUIT DIAGNOSIS >
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
[QR25DE]
2.CHECK FOR INTAKE AIR LEAK
1. Stop engine and check the following for connection.
Air duct
Vacuum hoses
PCV hose
Intake air passage between air duct to intake manifold
2. Start engine and let it idle.
3. Listen for an intake air leak after the mass air flow sensor.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK EXHAUST GAS LEAK
1.
2.
3.
Stop engine and visually check exhaust tube, three way catalyst and muffler for dents connection.
Start engine and let it idle.
Listen for an exhaust gas leak before three way catalyst (manifold).
JMBIA0163GB
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK FUEL PRESSURE
1. Release fuel pressure to zero. Refer to EC-147, "Work Procedure".
2. Check fuel pressure. Refer to EC-147, "Work Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 10.
5.CHECK MASS AIR FLOW SENSOR
With CONSULT
Check MASS AIR FLOW in DATA MONITOR mode of ENGINE using CONSULT.
For specification, refer to EC-503, "Mass Air Flow Sensor".
With GST
Check mass air flow sensor signal in Service $01 using GST.
For specification, refer to EC-503, "Mass Air Flow Sensor".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
grounds. Refer to EC-202, "Diagnosis Procedure".
6.CHECK FUNCTION OF FUEL INJECTOR-1
1.
2.
3.
With CONSULT
Start engine.
Perform POWER BALANCE in ACTIVE TEST mode of ENGINE using CONSULT.
Check that each circuit produces a momentary engine speed drop.
Revision: August 2014
EC-394
2015 Rogue NAM
P117A AIR FUEL RATIO
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Without CONSULT
1. Let engine idle.
2. Listen to each fuel injector operating sound.
Clicking noise should be heard.
EC
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Perform trouble diagnosis for fuel injector, refer to EC467, "Component Function Check".
D
PBIB3332E
7.CHECK FUNCTION OF FUEL INJECTOR-2
CAUTION:
Perform the following procedure in a place with no combustible objects and good ventilation.
1. Turn ignition switch OFF.
2. Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
3. Disconnect all fuel injector harness connectors.
4. Remove fuel tube assembly. Refer to EM-45, "Removal and Installation".
Keep fuel hose and all fuel injectors connected to fuel tube.
5. Disconnect all ignition coil harness connectors.
6. Prepare pans or saucers under each fuel injector.
7. Crank engine for approximately 3 seconds.
Fuel should be sprayed evenly for each fuel injector.
Fuel must not drip from the tip of fuel injector.
I
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace fuel injector. Refer to EM-45, "Removal and
Installation".
PBIA9666J
8.CHECK FUNCTION OF IGNITION COIL-1
CAUTION:
Perform the following steps in a well-ventilated area with no combustibles.
1. Turn ignition switch OFF.
2. Remove fuel pump fuse from IPDM E/R to release fuel pressure.
NOTE:
CONSULT must not be used to release fuel pressure. It develops again during the following steps,
if released by using CONSULT.
3. Start the engine.
4. After an engine stall, crank the engine two or three times to release all the fuel pressure.
5. Turn ignition switch OFF.
6. Disconnect all the harness connectors of ignition coil to prevent electric discharge from occurring in ignition coil.
7. Remove ignition coil assembly and spark plug of cylinder. Refer to EM-41, "Removal and Installation".
8. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
9. Connect spark plug and harness connector to ignition coil.
Revision: August 2014
EC-395
2015 Rogue NAM
P117A AIR FUEL RATIO
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
10. Allow a 13-17mm (0.52-0.66 in) spacing between spark plug and
grounded metal portion as shown in the figure to fix the ignition
coil with a rope or an equivalent.
11. Crank the engine for approximately 3 seconds to see if sparking
occurs between spark plug and the grounded metal portion.
Spark should be generated.
CAUTION:
The discharge voltage becomes 20 kV or higher. Therefore, always stay away from the spark plug and ignition
JMBIA0066GB
coil at least 50 cm (19.7 in) during the inspection.
Leaving a space of more than 17mm (0.66 in) may damage
the ignition coil.
NOTE:
When the gap is less than 13 mm (0.52 in), a the spark might be generated even if the coil is malfunctioning.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> GO TO 11.
9.CHECK COMPRESSION PRESSURE
Check compression pressure. Refer to EM-24, "Compression pressure".
Is the inspection result normal?
YES >> GO TO 14.
NO
>> Check pistons, piston rings, valves, valve seats and cylinder head gaskets.
10.DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES >> Replace fuel filter and fuel pump assembly. Refer to FL-5, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
11.CHECK FUNCTION OF IGNITION COIL-2
1.
2.
3.
Turn ignition switch OFF.
Disconnect spark plug and connect a non-malfunctioning spark plug.
Crank engine for approximately 3 seconds, and recheck whether spark is generated between the spark
plug and the grounded metal portion.
Spark should be generated.
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Check ignition coil, power transistor and their circuits. Refer to EC-473, "Component Function
Check".
12.CHECK SPARK PLUG
Check the initial spark plug for fouling, etc.
Is the inspection result normal?
YES >> 1. Repair or clean spark plug. Refer to EM-19,
"Removal and Installation".
2. GO TO 13.
NO
>> Replace spark plug(s) with standard type one(s). For
spark
plug
type,
refer
to
EM-120,
"General Specification".
SEF156I
13.CHECK FUNCTION OF IGNITION COIL-3
Revision: August 2014
EC-396
2015 Rogue NAM
P117A AIR FUEL RATIO
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
1. Reconnect the initial spark plugs.
2. Crank engine for approximately 3 seconds, and recheck whether spark is generated between the spark
plug and the grounded portion.
Spark should be generated.
EC
Is the inspection result normal?
YES >> GO TO 14.
NO
>> Replace spark plug(s) with standard type one(s). For spark plug type, refer to EM-120,
"General Specification".
14.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-397
2015 Rogue NAM
P1212 TCS COMMUNICATION LINE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1212 TCS COMMUNICATION LINE
Description
INFOID:0000000011278111
This CAN communication line is used to control the smooth engine operation during the TCS operation. Pulse
signals are exchanged between ECM and ABS actuator and electric unit (control unit).
Be sure to erase the malfunction information such as DTC not only for ABS actuator and electric unit
(control unit) but also for ECM after TCS related repair.
DTC Description
INFOID:0000000011278112
DTC DETECTION LOGIC
Freeze frame data is not stored in the ECM for this self-diagnosis.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P1212
TCS/CIRC
(TCS/CIRC)
DTC detecting condition
ECM can not receive the information from ABS actuator and electric unit
(control unit) continuously.
POSSIBLE CAUSE
Harness or connectors (CAN communication line is open or shorted.)
ABS actuator and electric unit (control unit)
Dead (Weak) battery
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-398, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278113
Perform the trouble diagnosis for TCS. Refer to BRC-64, "Work Flow".
NOTE:
If DTC P1212 is displayed with DTC UXXXX and/or P0607, perform the following trouble diagnosis.
Trouble diagnosis for DTC UXXXX Refer to EC-96, "DTC Index".
Revision: August 2014
EC-398
2015 Rogue NAM
P1212 TCS COMMUNICATION LINE
< DTC/CIRCUIT DIAGNOSIS >
Trouble diagnosis for DTC P0607 Refer to EC-379, "DTC Description".
[QR25DE]
A
EC
Revision: August 2014
EC-399
2015 Rogue NAM
P1217 ENGINE OVER TEMPERATURE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1217 ENGINE OVER TEMPERATURE
DTC Description
INFOID:0000000011278114
DTC DETECTION LOGIC
If the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will
rise.
When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is
indicated.
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P1217
ENG OVER TEMP
(ENG OVER TEMP)
DTC detecting condition
Cooling fan does not operate properly (Overheat).
Cooling fan system does not operate properly (Overheat).
Engine coolant was not added to the system using the proper filling
method.
Engine coolant is not within the specified range.
CAUTION:
When a malfunction is indicated, be sure to replace the coolant. Refer to CO-8, "Draining" and CO-9,
"Refilling". Also, replace the engine oil. Refer to LU-8, "Draining" and LU-8, "Refilling".
1. Fill radiator with coolant up to specified level with a filling speed of 2 liters per minute. Be sure to
use coolant with the proper mixture ratio. Refer to MA-12, "Anti-Freeze Coolant Mixture Ratio".
2. After refilling coolant, run engine to ensure that no water-flow noise is emitted.
POSSIBLE CAUSE
Harness or connectors (Cooling fan circuit is open or shorted.)
IPDM E/R
Cooling fan motor
Radiator hose
Radiator
Radiator cap
Reservoir tank
Water pump
Thermostat
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PERFORM COMPONENT FUNCTION CHECK-1
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.
Wrap a thick cloth around cap. Carefully remove the cap by turning it a quarter turn to allow built-up
pressure to escape. Then turn the cap all the way off.
Revision: August 2014
EC-400
2015 Rogue NAM
P1217 ENGINE OVER TEMPERATURE
< DTC/CIRCUIT DIAGNOSIS >
Check the coolant level in the reservoir tank and radiator.
Allow engine to cool before checking coolant level.
Is the coolant level in the reservoir tank and/or radiator below the
proper range?
YES >> Proceed to EC-401, "Diagnosis Procedure".
NO
>> GO TO 3.
[QR25DE]
A
EC
3.PERFORM COMPONENT FUNCTION CHECK-2
SEF621W
Confirm whether customer filled the coolant or not.
Did customer fill the coolant?
YES >> Proceed to EC-401, "Diagnosis Procedure".
NO
>> GO TO 4.
4.PERFORM COMPONENT FUNCTION CHECK-3
With CONSULT
1. Turn ignition switch ON.
2. Perform FAN DUTY CONTROL in ACTIVE TEST mode with CONSULT.
3. Make sure that cooling fan speed varies according to the percentage.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-401, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278115
If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or
P0607.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
1.CHECK DTC PRIORITY
2.CHECK COOLING FAN OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Perform FAN DUTY CONTROL in ACTIVE TEST mode with CONSULT.
3. Make sure that cooling fan speed varies according to the percentage.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Proceed to EC-461, "Diagnosis Procedure".
3.CHECK COOLING SYSTEM FOR LEAK-1
Check cooling system for leak. Refer to CO-8, "Inspection".
Is leakage detected?
YES >> GO TO 4.
NO
>> GO TO 5.
4.CHECK COOLING SYSTEM FOR LEAK-2
Check the following for leak.
Hose (Refer to CO-8, "Inspection".)
Radiator (Refer to CO-12, "RADIATOR : Inspection".)
Water pump (Refer to CO-19, "Removal and Installation".)
Revision: August 2014
EC-401
2015 Rogue NAM
P1217 ENGINE OVER TEMPERATURE
< DTC/CIRCUIT DIAGNOSIS >
>> Repair or replace malfunctioning part.
[QR25DE]
5.CHECK RADIATOR CAP
Check radiator cap. Refer to CO-12, "RADIATOR CAP : Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace radiator cap. Refer to CO-13, "Exploded View".
6.CHECK THERMOSTAT
Check thermostat. Refer to CO-21, "Removal and Installation".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace thermostat. Refer to CO-21, "Removal and Installation".
7.CHECK ENGINE COOLANT TEMPERATURE SENSOR
Refer to EC-215, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace engine coolant temperature sensor. Refer to CO-23, "Exploded View".
8.OVERHEATING CAUSE ANALYSIS
If the cause cannot be isolated, check the CO-6, "Troubleshooting Chart".
>> INSPECTION END
Revision: August 2014
EC-402
2015 Rogue NAM
P1225 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1225 TP SENSOR
DTC Description
INFOID:0000000011278116
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
CTP LEARNING-B1
(CTP LEARNING-B1)
P1225
EC
DTC detecting condition
Closed throttle position learning value is excessively low.
POSSIBLE CAUSE
Electric throttle control actuator (TP sensor 1 and 2)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-403, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
L
INFOID:0000000011278117
1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
2.
3.
Turn ignition switch OFF.
Remove the intake air duct. Refer to EM-26, "Exploded View".
Check if foreign matter is caught between the throttle valve and
the housing.
Is the inspection result normal?
YES >> Replace electric throttle control actuator. Refer to EM29, "Removal and Installation".
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside, then perform throttle valve
closed position learning. Refer to EC-143, "Work Procedure".
JSBIA2864ZZ
Revision: August 2014
EC-403
2015 Rogue NAM
P1226 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1226 TP SENSOR
DTC Description
INFOID:0000000011278118
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P1226
CTP LEARNING-B1
(CTP LEARNING-B1)
DTC detecting condition
Closed throttle position learning is not performed successfully, repeatedly.
POSSIBLE CAUSE
Electric throttle control actuator (TP sensor 1 and 2)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF, wait at least 10 seconds.
3. Turn ignition switch ON.
4. Repeat steps 2 and 3 for 32 times.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-404, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278119
1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
2.
3.
Turn ignition switch OFF.
Remove the intake air duct. Refer to EM-26, "Exploded View".
Check if foreign matter is caught between the throttle valve and
the housing.
Is the inspection result normal?
YES >> Replace electric throttle control actuator. Refer to EM29, "Removal and Installation".
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside, then perform throttle valve
closed position learning. Refer to EC-143, "Work Procedure".
JSBIA2864ZZ
Revision: August 2014
EC-404
2015 Rogue NAM
P155D GENERATOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P155D GENERATOR
DTC Description
INFOID:0000000011278120
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
GENERATOR
(Generator)
P155D
EC
DTC detecting condition
ECM receives mechanical malfunction signal sent from generator.
ECM receives electrical malfunction signal sent from generator.
POSSIBLE CAUSE
Generator
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted. always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and let it idle at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-178, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278121
1.CHECK CHARGING SYSTEM
Perform trouble diagnosis for charging system. Refer to EC-168, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace generator. Refer to CHG-20, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-405
2015 Rogue NAM
P1564 ASCD STEERING SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1564 ASCD STEERING SWITCH
DTC Description
INFOID:0000000011278122
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P1564
ASCD SW
(ASCD switch)
DTC detecting condition
An excessively high voltage signal from the ASCD steering switch is sent
to ECM.
ECM detects that input signal from the ASCD steering switch is out of the
specified range.
ECM detects that the ASCD steering switch is stuck ON.
POSSIBLE CAUSE
Harness or connectors (ASCD steering switch circuit is open or shorted.)
ASCD steering switch
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1564 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Wait at least 10 seconds.
3. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.
4. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
5. Press ACCEL/RES switch for at least 10 seconds, then release it and wait at least 10 seconds.
6. Press COAST/SET switch for at least 10 seconds, then release it and wait at least 10 seconds.
7. Check DTC.
Is DTC detected?
YES >> Proceed to EC-406, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278123
1.CHECK DTC PRIORITY
If DTC P1564 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
Revision: August 2014
EC-406
2015 Rogue NAM
P1564 ASCD STEERING SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> GO TO 2.
2.CHECK ASCD STEERING SWITCH CIRCUIT
With CONSULT
Turn ignition switch ON.
EC
Select CANCEL SW, RESUME/ACC SW and SET SW in DATA MONITOR mode of ENGINE
using CONSULT.
3. Check each item indication as per the following conditions.
C
1.
2.
Monitor item
Condition
MAIN SW
MAIN switch
CANCEL SW
CANCEL switch
RESUME/ACC
SW
ACCEL/RES switch
SET SW
COAST/SET switch
Indication
Pressed
ON
Released
OFF
Pressed
ON
Released
OFF
Pressed
ON
Released
OFF
Pressed
ON
Released
OFF
Without CONSULT
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector terminals.
ECM
+
Connector
Voltage
(Approx.)
Condition
Terminal
E16
110
111
MAIN switch: Pressed
0V
CANCEL switch: Pressed
1V
COAST/SET switch: Pressed
2V
ACCEL/RES switch: Pressed
3V
All ASCD steering switches: Released
4V
Is the inspection result normal?
YES >> GO TO 6.
NO
>> GO TO 3.
3.CHECK ASCD STEERING SWITCH GROUND CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect combination switch (spiral cable) harness connector.
Check the continuity between combination switch (spiral cable) and ECM harness connector.
+
Combination switch
(Spiral cable)
ECM
O
Continuity
Connector
Terminal
Connector
Terminal
M30
E16
111
P
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT
Revision: August 2014
EC-407
2015 Rogue NAM
P1564 ASCD STEERING SWITCH
< DTC/CIRCUIT DIAGNOSIS >
1. Check the continuity between ECM harness connector and combination switch.
+
Combination switch
(Spiral cable)
ECM
[QR25DE]
Continuity
Connector
Terminal
Connector
Terminal
M30
E16
110
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK ASCD STEERING SWITCH
Refer to EC-408, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace ASCD steering switch. Refer to ST-11, "Removal and Installation".
6.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278124
1.CHECK ASCD STEERING SWITCH
1.
2.
Disconnect combination switch (spiral cable) harness connector.
Check the resistance between combination switch harness connector terminals as per the following conditions.
Combination switch
(Spiral cable)
Connector
Condition
Terminals
MAIN switch: Pressed
M90
Resistance
(Approx.)
27
26
CANCEL switch: Pressed
250
COAST/SET switch: Pressed
660
ACCEL/RES switch: Pressed
1,480
All ASCD steering switches: Released
4,000
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace ASCD steering switch. Refer to ST-11, "Exploded View".
Revision: August 2014
EC-408
2015 Rogue NAM
P1568 SIGNAL INVALID
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1568 SIGNAL INVALID
DTC Description
INFOID:0000000011278125
DTC DETECTION LOGIC
DTC No.
P1568
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
ICC COMMAND VALUE
(Intelligent cruise control command value)
ECM detects that a throttle valve opening angle request signal sent from
chassis control module is difference from the specified value calculated by
ECM.
POSSIBLE CAUSE
Chassis control module
ECM
FAIL-SAFE
Active trace control does not function.
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1568 is displayed with DTC UXXXX, first perform the confirmation procedure for DTC UXXXX.
Is applicable DTC detected?
YES >> Perform diagnosis for detected DTC. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
2.PRECONDITIONING
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-409, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278126
1.CHECK DTC PRIORITY
If DTC P1568 is displayed with DTC UXXXX, first perform the confirmation procedure for DTC UXXXX.
Is applicable DTC detected?
YES >> Perform diagnosis for detected DTC. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK SELF-DIAGNOSTIC RESULT OF CHASSIS CONTROL MODULE
Check that the chassis control module does not detect any DTC.
Is any DTC detected?
YES >> GO TO 3.
NO
>> Replace chassis control module. Refer to DAS-286, "Removal and Installation".
3.REPLACE CHASSIS CONTROL MODULE
Revision: August 2014
EC-409
2015 Rogue NAM
P1568 SIGNAL INVALID
< DTC/CIRCUIT DIAGNOSIS >
1. Replace chassis control module. Refer to DAS-286, "Removal and Installation".
2. Perform DTC Confirmation Procedure again.
Is DTC P1568 detected again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-410
[QR25DE]
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1572 BRAKE PEDAL POSITION SWITCH
DTC Description
INFOID:0000000011278127
DTC DETECTION LOGIC
EC
NOTE:
This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not stored
in ECM memory. And in that case, 1st trip DTC and 1st trip freeze frame data are displayed. 1st trip
DTC is erased when ignition switch OFF. And even when malfunction A is detected in two consecutive
trips, DTC is not stored in ECM memory.
ASCD BRAKE SW
(ASCD BRAKE SW)
P1572
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
When the vehicle speed is above 30 km/h (19 MPH), ON signals from
the stop lamp switch and the brake pedal position switch are sent to
the ECM at the same time.
Brake pedal position switch signal is not sent to ECM for extremely
long time while the vehicle is driving.
POSSIBLE CAUSE
Harness or connectors
Stop lamp switch circuit is shorted.
Brake pedal position switch circuit is shorted.
Stop lamp switch
Brake pedal position switch
Incorrect stop lamp switch installation
Incorrect brake pedal position switch installation
ECM
FAIL-SAFE
Not applicable
J
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1572 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
NOTE:
Procedure for malfunction B is not described here. It takes extremely long time to complete procedure for malfunction B. By performing procedure for malfunction A, the incident that causes malfunction B can be
detected.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
Start engine.
Press MAIN switch and make sure that CRUISE indicator is displayed in combination meter.
Drive the vehicle for at least 5 consecutive seconds as per the following conditions.
CAUTION:
Revision: August 2014
>> GO TO 3.
1.
2.
3.
EC-411
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
Vehicle speed
More than 30 km/h (19 mph)
Selector lever
Suitable position
4. Check DTC.
Is DTC detected?
YES >> Proceed to EC-418, "Diagnosis Procedure".
NO
>> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Drive the vehicle for at least 5 consecutive seconds as per the following conditions.
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
Vehicle speed
More than 30 km/h (19 mph)
Selector lever
Suitable position
Driving location
Depress the brake pedal for more
than five seconds so as not to come
off from the above-mentioned vehicle speed.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-418, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278128
1.CHECK DTC PRIORITY
If DTC P1572 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK OVERALL FUNCTION-1
1.
2.
3.
With CONSULT
Turn ignition switch ON.
Select BRAKE SW1 in DATA MONITOR mode of ENGINE using CONSULT.
Check BRAKE SW1 indication as per the following conditions.
Monitor item
BRAKE SW1
1.
2.
Condition
Brake pedal
Indication
Slightly depressed
OFF
Fully released
ON
Without CONSULT
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following.
Revision: August 2014
EC-412
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
+
Connector
Voltage
(Approx.)
Condition
Terminal
E16
116
128
Slightly depressed
Brake pedal
Fully released
EC
0V
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 4.
3.CHECK OVERALL FUNCTION-2
With CONSULT
Select BRAKE SW2 and check indication as per the following conditions.
Monitor item
Condition
BRAKE SW2
Brake pedal
Indication
Slightly depressed
ON
Fully released
OFF
Without CONSULT
Check the voltage between ECM harness connector terminals as per the following conditions.
ECM
+
Connector
E16
Voltage
(Approx.)
Condition
Terminal
115
128
Brake pedal
Slightly depressed
Battery voltage
Fully released
0V
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> GO TO 7.
4.CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect brake pedal position switch harness connector.
Turn ignition switch ON.
Check the voltage between brake pedal position switch harness connector and ground.
Brake pedal position switch
Connector
Terminal
E6
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Perform the trouble diagnosis for power supply circuit.
5.CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between brake pedal position switch harness connector and ECM harness connector.
Revision: August 2014
EC-413
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Brake pedal position switch
ECM
Continuity
Connector
Terminal
Connector
Terminal
E6
E16
116
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK BRAKE PEDAL POSITION SWITCH
Check the brake pedal position switch. Refer to EC-414, "Component Inspection (Brake Pedal Position
Switch)"
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace brake pedal position switch. Refer to BR-20, "Exploded View".
7.CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect stop lamp switch harness connector.
Check the voltage between stop lamp switch harness connector and ground.
+
Voltage
Ground
Battery voltage
Stop lamp switch
Connector
Terminal
E38
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Perform the trouble diagnosis for power supply circuit.
8.CHECK STOP LAMP SWITCH GROUND CIRCUIT
1.
Check the continuity between stop lamp switch harness connector and ECM harness connector.
+
Stop lamp switch
ECM
Continuity
Connector
Terminal
Connector
Terminal
E38
E16
115
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.CHECK STOP LAMP SWITCH
Check the stop lamp switch. Refer to EC-415, "Component Inspection (Stop Lamp Switch)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace stop lamp switch. Refer to BR-20, "Exploded View".
Component Inspection (Brake Pedal Position Switch)
INFOID:0000000011278129
1.CHECK BRAKE PEDAL POSITION SWITCH-1
1.
2.
Turn ignition switch OFF.
Disconnect brake pedal position harness connector.
Revision: August 2014
EC-414
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
3. Check the continuity between brake pedal position switch terminals as per the following conditions.
A
Brake pedal position switch
Condition
Continuity
EC
Terminals
Fully released
1
Brake pedal
Slightly depressed
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK BRAKE PEDAL POSITION SWITCH-2
1.
2.
Adjust brake pedal position switch installation. Refer to BR-15, "Adjustment".
Check the continuity between brake pedal position switch terminals as per the following conditions.
Brake pedal position switch
Condition
Continuity
Terminals
G
Fully released
Brake pedal
Slightly depressed
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace brake pedal position switch. Refer to BR-20, "Exploded View".
Component Inspection (Stop Lamp Switch)
INFOID:0000000011278130
1.CHECK STOP LAMP SWITCH-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect stop lamp switch harness connector.
Check the continuity between stop lamp switch terminals as per the following conditions.
Stop lamp switch
Condition
Continuity
Terminals
Fully released
1
Brake pedal
Slightly depressed
Not existed
Existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK STOP LAMP SWITCH-2
1.
2.
Adjust stop lamp switch installation. Refer to BR-7, "Inspection".
Check the continuity between stop lamp switch terminals as per the following conditions.
Revision: August 2014
EC-415
2015 Rogue NAM
P1572 BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Stop lamp switch
Condition
Continuity
Terminals
Fully released
1
Brake pedal
Slightly depressed
Not existed
Existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace stop lamp switch. Refer to BR-20, "Exploded View".
Revision: August 2014
EC-416
2015 Rogue NAM
P1574 ASCD VEHICLE SPEED SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1574 ASCD VEHICLE SPEED SENSOR
Description
INFOID:0000000011278131
The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combina- EC
tion meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD
control. Refer to EC-49, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description" for ASCD
functions.
C
DTC Description
INFOID:0000000011278132
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
ASCD VHL SPD SEN
(ASCD VHL SPD SEN)
P1574
D
DTC detecting condition
ECM detects a difference between two vehicle speed signals is out of the
specified range.
POSSIBLE CAUSE
Harness or connectors (CAN communication line is open or shorted.)
ABS actuator and electric unit (control unit)
TCM
ECM
FAIL-SAFE
H
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1574 is displayed with DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or P060B,
first perform the trouble diagnosis for DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or
P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
2.
Start engine.
Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
3. Check DTC.
Is DTC detected?
YES >> Proceed to EC-418, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-417
2015 Rogue NAM
P1574 ASCD VEHICLE SPEED SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278133
1.CHECK DTC PRIORITY
If DTC P1574 is displayed with DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or P060B,
first perform the trouble diagnosis for DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or
P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-47, "CONSULT Function".
Is DTC detected?
NO
>> GO TO 3.
YES >> Perform trouble shooting relevant to DTC indicated.
3.CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit). Refer to BRC-42, "CONSULT Function".
Is DTC detected?
NO
>> INSPECTION END
YES >> Perform trouble shooting relevant to DTC indicated.
Revision: August 2014
EC-418
2015 Rogue NAM
P1715 INPUT SPEED SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1715 INPUT SPEED SENSOR
Description
INFOID:0000000011278134
ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for EC
engine control.
DTC Description
INFOID:0000000011278135
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
IN PULY SPEED
(IN PULY SPEED)
P1715
DTC detecting condition
Input speed sensor signal is different from the theoretical value calculated
by ECM from output speed sensor signal and engine rpm signal.
POSSIBLE CAUSE
Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (Input speed sensor circuit is open or shorted.)
TCM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or
P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606,
P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and drive the vehicle at more than 50 km/h (31 MPH) for at least 5 seconds.
CAUTION:
Always drive vehicle at a safe speed.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-419, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278136
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or
P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606,
P0607, P060A, or P060B.
Is applicable DTC detected?
Revision: August 2014
EC-419
2015 Rogue NAM
P1715 INPUT SPEED SENSOR
< DTC/CIRCUIT DIAGNOSIS >
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
[QR25DE]
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-47, "CONSULT Function".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Perform trouble shooting relevant to DTC indicated.
3.REPLACE TCM
Replace TCM. Refer to TM-202, "Removal and Installation".
>> INSPECTION END
Revision: August 2014
EC-420
2015 Rogue NAM
P1805 BRAKE SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P1805 BRAKE SWITCH
DTC Description
INFOID:0000000011278137
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
BRAKE SW/CIRCUIT
(BRAKE SW/CIRCUIT)
P1805
DTC detecting condition
A stop lamp switch signal is not sent to ECM for extremely long time while
the vehicle is driving.
POSSIBLE CAUSE
Harness or connectors (Stop lamp switch circuit is open or shorted.)
Stop lamp switch
FAIL-SAFE
ECM controls the electric throttle control actuator by regulating the throttle opening to a small range. Therefore, acceleration will be poor.
Vehicle condition
Driving condition
When engine is idling
Normal
When accelerating
Poor acceleration
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Fully depress the brake pedal for at least 5 seconds.
3. Erase the DTC.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-421, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278138
1.CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect stop lamp switch harness connector.
Check the voltage between stop lamp switch harness connector and ground.
+
Stop lamp switch
Connector
Terminal
E38
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Perform the trouble diagnosis for power supply circuit.
2.CHECK STOP LAMP SWITCH GROUND CIRCUIT
1.
2.
Disconnect ECM harness connector.
Check the continuity between stop lamp switch harness connector and ECM harness connector.
Revision: August 2014
EC-421
2015 Rogue NAM
P1805 BRAKE SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Stop lamp switch
ECM
Continuity
Connector
Terminal
Connector
Terminal
E38
E16
115
Existed
3. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.CHECK STOP LAMP SWITCH
Check the stop lamp switch. Refer to EC-415, "Component Inspection (Stop Lamp Switch)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace stop lamp switch. Refer to BR-20, "Exploded View".
Component Inspection (Stop Lamp Switch)
INFOID:0000000011278139
1.CHECK STOP LAMP SWITCH-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect stop lamp switch harness connector.
Check the continuity between stop lamp switch terminals as per the following conditions.
Stop lamp switch
Condition
Continuity
Terminals
Fully released
1
Brake pedal
Slightly depressed
Not existed
Existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK STOP LAMP SWITCH-2
1.
2.
Adjust stop lamp switch installation. Refer to BR-15, "Adjustment".
Check the continuity between stop lamp switch terminals as per the following conditions.
Stop lamp switch
Condition
Continuity
Terminals
Fully released
1
Brake pedal
Slightly depressed
Not existed
Existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace stop lamp switch. Refer to BR-20, "Exploded View".
Revision: August 2014
EC-422
2015 Rogue NAM
P2004 INTAKE MANIFOLD RUNNER CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2004 INTAKE MANIFOLD RUNNER CONTROL VALVE
DTC Description
INFOID:0000000011278140
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
TUMBLE CONT/V
(Intake manifold runner control stuck open
bank 1)
The target angle of intake manifold runner control valve controlled by ECM
and the input signal from intake manifold runner control valve position sensor is not in the normal range.
DTC No.
P2004
EC
POSSIBLE CAUSE
Harness or connectors (Intake manifold runner control valve motor circuit is open or shorted.)
Intake manifold runner control valve motor
Intake manifold runner control valve is stuck
FAIL-SAFE
Traveling control mode (Engine output control)
Device fix mode
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above 7C (19F)
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Make sure that COOLAN TEMP/S indicates between 7C (19F) to 60C (140F).
If not, cool engine down or warm engine up until COOLAN TEMP/S indicates between 7C (19F) to
60C (140F). Then go to the following steps.
4. Fully release accelerator pedal and wait at least 10 seconds.
5. Depress accelerator pedal and wait at least 10 seconds.
6. Check 1st trip DTC.
With GST
Following the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Proceed to EC-423, "Diagnosis Procedure".
NO
>> INSPECTION END
1.
2.
3.
Diagnosis Procedure
INFOID:0000000011278141
1.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR POWER SUPPLY
1.
2.
Turn ignition switch ON.
Check the voltage between ECM harness connector.
ECM
+
Voltage
Connector
Terminal
Connector
Terminal
F52
50
E16
128
Revision: August 2014
Battery voltage
EC-423
2015 Rogue NAM
P2004 INTAKE MANIFOLD RUNNER CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR POWER SUPPLY CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F52
50
E119
Existed
5. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR OUTPUT SIGNAL CIRCUIT
1.
2.
Disconnect intake manifold runner control valve motor harness connector.
Check the continuity between intake manifold runner control valve motor harness connector and ECM
harness connector.
+
Intake manifold runner control valve motor
ECM
Connector
Terminal
Connector
1
F19
F52
2
Continuity
Terminal
49
Not existed
51
Existed
49
Existed
51
Not existed
3. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR
Check the intake manifold runner control valve motor. Refer to EC-424, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace intake manifold assembly. Refer to EM-29, "Removal and Installation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278142
1.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE
1.
2.
With CONSULT
Turn ignition switch ON.
Select DATA MONITOR mode with CONSULT.
Revision: August 2014
EC-424
2015 Rogue NAM
P2004 INTAKE MANIFOLD RUNNER CONTROL VALVE
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
3. Make sure that COOLAN TEMP/S indicates between 7C (19F) to 60C (140F).
If not, cool engine down or warm engine up until COOLAN TEMP/S indicates between 7C (19F) to A
60C (140F). Then go to the following steps.
4. Fully release accelerator pedal and make sure that TUMBLE POS SEN indicates between 2.8 V to 4.1
V.
EC
5. Depress accelerator pedal and make sure that TUMBLE POS SEN indicates between 0.2 V to 1.4 V.
6. Check 1st trip DTC.
With GST
C
Following the procedure With CONSULT above.
Is 1st trip DTC detected?
YES >> Replace intake manifold assembly. Refer to EM-29, "Removal and Installation".
D
NO
>> GO TO 2.
2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect intake manifold runner control valve motor harness connector.
Check the resistance between intake manifold runner control valve motor terminals as per the following.
Intake manifold runner control valve
motor
+
Resistance
(Approx.)
4.64 - 6.30 [at 25C (77F)]
Terminals
1
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace intake manifold assembly. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-425
2015 Rogue NAM
P2014, P2016, P2017, P2018 INTAKE MANIFOLD RUNNER CONTROL VALVE
POSITION SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2014, P2016, P2017, P2018 INTAKE MANIFOLD RUNNER CONTROL
VALVE POSITION SENSOR
DTC Description
INFOID:0000000011278143
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P2014
IN/MANIFOLD RUNNER POS SEN B1
(Intake manifold runner position sensor/
switch circuit bank 1)
P2016
IN/MANIFOLD RUNNER POS SEN B1
(Intake manifold runner position sensor/
switch circuit low bank 1)
P2017
IN/MANIFOLD RUNNER POS SEN B1
(Intake manifold runner position sensor/
switch circuit high bank 1)
P2018
IN/MANIFOLD RUNNER POS SEN B1
(Intake manifold runner position sensor/
switch circuit intermittent bank 1)
DTC detecting condition
An excessively low voltage from the sensor is sent to ECM.
An excessively high voltage from the sensor is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (Intake manifold runner control position sensor circuit is shorted.)
Intake manifold runner control position sensor
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for
DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-427, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
EC-426
2015 Rogue NAM
P2014, P2016, P2017, P2018 INTAKE MANIFOLD RUNNER CONTROL VALVE
POSITION SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278144
1.CHECK DTC PRIORITY
If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for
EC
DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
C
NO
>> GO TO 2.
2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect intake valve manifold runner control valve position sensor harness connector.
Turn ignition switch ON.
Check the voltage between intake valve manifold runner control valve position sensor harness connector.
Intake manifold runner control valve position sensor
+
Connector
Voltage
(Approx.)
5V
Terminal
F20
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 3.
3.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT
Check the voltage between intake valve manifold runner control valve position sensor harness connector and
ground.
+
Intake manifold runner control valve
position sensor
Connector
Terminal
F20
Voltage
(Approx.)
K
Ground
5V
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Perform the trouble diagnosis for power supply circuit.
4.CHECK ECM GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between ECM harness connector and ground.
+
ECM
Connector
Terminal
F51
16
F52
52
E16
123
Continuity
Ground
Existed
128
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 8.
Revision: August 2014
EC-427
2015 Rogue NAM
P2014, P2016, P2017, P2018 INTAKE MANIFOLD RUNNER CONTROL VALVE
POSITION SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> Repair or replace error-detected parts.
5.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between intake manifold runner control valve position sensor harness connector and
ECM harness connector.
+
Intake manifold runner control
valve position sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F20
F52
92
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between intake manifold runner control valve position sensor harness connector and
ECM harness connector.
+
Intake manifold runner control
valve position sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F20
F52
83
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
7.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace intake manifold assembly. Refer to EM-29, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-428
2015 Rogue NAM
P2096, P2097 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2096, P2097 A/F SENSOR 1
DTC Description
INFOID:0000000011278145
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2096
POST CATALYST FUEL TRIM SYS B1
(Post catalyst fuel trim system too lean bank
1)
The output voltage computed by ECM from the A/F sensor 1 signal is shifts
to the lean side for a specified period.
P2097
POST CATALYST FUEL TRIM SYS B1
(Post catalyst fuel trim system too rich bank
1)
The A/F signal computed by ECM from the A/F sensor 1 signal is shifts to
the rich side for a specified period.
DTC No.
POSSIBLE CAUSE
A/F sensor 1
A/F sensor 1 heater
Heated oxygen sensor 2
Fuel pressure
Fuel injector
Intake air leaks
Exhaust gas leaks
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 at idle.
>> GO TO 2.
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for 1 minute under no load.
4. Let engine idle for 1 minute.
5. Keep engine speed between 2,500 and 3,000 rpm for 20 minutes.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-429, "Diagnosis Procedure".
NO
>> INSPECTION END
INFOID:0000000011278146
1.CHECK HARNESS CONNECTOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Check harness connector for water.
Water should not exit.
Revision: August 2014
EC-429
2.PERFORM DTC CONFIRMATION PROCEDURE
Diagnosis Procedure
2015 Rogue NAM
P2096, P2097 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace harness connector.
2.RETIGHTEN A/F SENSOR 1 AND HEATED OXYGEN SENSOR 2
Loosen and retighten the A/F sensor 1 and heated oxygen sensor 2. Refer to EM-32, "Exploded View", EX-5,
"Exploded View".
>> GO TO 3.
3.CHECK FOR EXHAUST GAS LEAK
1. Start engine and run it at idle.
2. Listen for an exhaust gas leak before the three way catalyst 2.
Is exhaust gas leak detected?
YES >> Repair or replace malfunctioning parts.
NO
>> GO TO 4.
4.CHECK FOR INTAKE AIR LEAK
1. Reconnect A/F sensor 1 harness connector.
2. Start engine and run it at idle.
3. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES >> Repair or replace malfunctioning parts.
NO
>> GO TO 5.
5.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1. Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
2. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171 or P0172 detected? Is it difficult to start engine?
YES >> Perform trouble diagnosis for DTC P0171 or P0172. Refer to EC-263, "DTC Description" or EC268, "DTC Description".
NO
>> GO TO 6.
6.CHECK A/F SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect A/F sensor 1 harness connector.
Turn ignition switch ON.
Check the voltage between A/F sensor 1 harness connector and ground.
+
A/F sensor 1
Connector
Terminal
F18
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 8.
NO
>> GO TO 7.
7.CHECK A/F SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.
Revision: August 2014
EC-430
2015 Rogue NAM
P2096, P2097 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
A/F sensor 1
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F18
F35
75
EC
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
8.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
+
A/F sensor 1
ECM
Connector
Terminal
1
F18
4.
Connector
Continuity
Terminal
41
F51
Existed
45
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
+
A/F sensor 1
Connector
Continuity
Ground
Not existed
1
2
+
ECM
F51
Terminal
F18
Connector
Continuity
Terminal
41
45
L
Ground
Not existed
5. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.CHECK A/F SENSOR 1 HEATER
Check the A/F sensor 1 heater. Refer to EC-189, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 10.
NO
>> GO TO 12.
10.CHECK HEATED OXYGEN SENSOR 2
Check heated oxygen sensor 2. Refer to EC-242, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 11.
NO
>> Replace heated oxygen sensor 2. Refer to EX-5, "Exploded View".
Revision: August 2014
EC-431
2015 Rogue NAM
P2096, P2097 A/F SENSOR 1
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
11.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Repair or replace error-detected parts.
12.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1. Refer to EM-32, "Exploded View".
CAUTION:
Discard any sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard
surface such as a concrete floor; use a new one.
Before installing new sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner
[commercial service tool (J-43897-18 or J-43897-12)] and approved Anti-seize Lubricant (commercial
service tool).
Do you have CONSULT?
YES >> GO TO 13.
NO
>> GO TO 14.
13.CONFIRM A/F ADJUSTMENT DATA
With CONSULT
1. Turn ignition switch ON.
2. Select A/F ADJ-B1 in DATA MONITOR mode of ENGINE using CONSULT.
3. Make sure that 0.000 is displayed on CONSULT screen.
Is 0.000 displayed?
YES >> INSPECTION END
NO
>> GO TO 14.
14.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
Clear the mixture ratio self-learning value. Refer to EC-146, "Work Procedure".
Do you have CONSULT?
YES >> GO TO 15.
NO
>> INSPECTION END
15.CONFIRM A/F ADJUSTMENT DATA
1.
2.
3.
With CONSULT
Turn ignition switch ON.
Select A/F ADJ-B1 in DATA MONITOR mode of ENGINE using CONSULT.
Make sure that 0.000 is displayed on CONSULT screen.
>> INSPECTION END
Revision: August 2014
EC-432
2015 Rogue NAM
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
DTC Description
INFOID:0000000011278147
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2100
ETC MOT PWR-B1
(Throttle actuator A control motor circuit/
open)
ECM detects a voltage of power source for throttle control motor is excessively low.
P2103
ETC MOT PWR-B1
(Throttle actuator A control motor circuit
high)
ECM detect the throttle control motor relay is stuck ON.
DTC No.
POSSIBLE CAUSE
DTC P2100
Harness or connectors (Throttle control motor relay circuit is open.)
Throttle control motor relay
DTC P2103
Harness or connectors (Throttle control motor relay circuit is shorted.)
Throttle control motor relay
FAIL-SAFE
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx.
5 degrees) by the return spring.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V.
Witch DTC is detected?
P2100 >> GO TO 2.
P2103 >> GO TO 3.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P2100
3.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P2103
1. Turn ignition switch ON and wait at least 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-434, "Diagnosis Procedure".
NO
>> INSPECTION END
EC-433
1. Turn ignition switch ON and wait at least 2 seconds.
2. Start engine and let it idle for 5 seconds.
3. Check DTC.
Is DTC detected?
YES >> Proceed to EC-434, "Diagnosis Procedure".
NO
>> INSPECTION END
Revision: August 2014
2015 Rogue NAM
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure
INFOID:0000000011278148
1.CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY
1.
2.
Turn ignition switch OFF.
Check the voltage between ECM harness connector and ground.
+
ECM
Voltage
Connector
Terminal
Connector
Terminal
F51
E16
128
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT
1.
2.
3.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F51
F35
72
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL
Check the voltage between ECM harness connector and ground as per the following conditions.
ECM
Condition
Connector
Terminal
Connector
Terminal
F51
21
E16
128
Voltage
(Approx.)
Ignition switch: OFF
0V
Ignition switch: ON
Battery voltage
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT
1.
2.
3.
4.
5.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F51
21
F35
67
Existed
Also check harness for short to ground and to power.
Revision: August 2014
EC-434
2015 Rogue NAM
P2100, P2103 THROTTLE CONTROL MOTOR RELAY
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
[QR25DE]
A
5.CHECK INTERMITTENT INCIDENT
EC
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-435
2015 Rogue NAM
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
DTC Description
INFOID:0000000011278149
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P2101
ETC FNCTN/CIRC-B1
(Throttle actuator A control motor circuit
range/performance)
DTC detecting condition
Electric throttle control function does not operate properly.
POSSIBLE CAUSE
Harness or connectors (Throttle control motor circuit is open or shorted.)
Electric throttle control actuator
FAIL-SAFE
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx.
5 degrees) by the return spring.
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P2101 is displayed with DTC P2100 or P2119, first perform the trouble diagnosis for DTC P2100 or
P2119.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V when
engine is running.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 2 seconds.
2. Start engine and let it idle for 5 seconds.
3. Check DTC.
Is DTC detected?
YES >> Proceed to EC-436, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278150
1.CHECK DTC PRIORITY
If DTC P2101 is displayed with DTC P2100 or P2119, first perform the trouble diagnosis for DTC P2100 or
P2119.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-96, "DTC Index".
NO
>> GO TO 2.
2.CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL
Revision: August 2014
EC-436
2015 Rogue NAM
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
< DTC/CIRCUIT DIAGNOSIS >
Check the voltage between ECM harness connector terminals as per the following conditions.
[QR25DE]
A
ECM
Voltage
(Approx.)
Condition
Connector
Terminal
Connector
Terminal
F51
21
E16
128
Ignition switch: OFF
0V
Ignition switch: ON
Battery voltage
EC
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 3.
1.
3.CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F51
F35
72
Existed
2. Also check harness for short to ground.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
+
ECM
IPDM E/R
Terminal
Connector
Terminal
F51
21
F35
67
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
5.CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT
1.
2.
3.
4.
Continuity
Connector
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
Revision: August 2014
EC-437
2015 Rogue NAM
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Electric throttle control actuator
ECM
Connector
Terminal
Connector
Terminal
5
F50
Continuity
F51
6
Existed
Not existed
Not existed
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Remove the intake air duct. Refer to EM-26, "Exploded View".
2. Check if foreign matter is caught between the throttle valve and the housing.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Remove the foreign matter and clean the electric throttle control actuator inside, then perform
throttle valve closed position learning. Refer to EC-143, "Work Procedure".
7.CHECK THROTTLE CONTROL MOTOR
Check the throttle control motor. Refer to EC-438, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278151
1.CHECK THROTTLE CONTROL MOTOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Check the resistance between electric throttle control actuator terminals as per the following.
Electric throttle control actuator
+
Resistance
(Approx.)
1 - 15 [at 25C (77F)]
Terminals
5
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-438
2015 Rogue NAM
P2118 THROTTLE CONTROL MOTOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2118 THROTTLE CONTROL MOTOR
DTC Description
INFOID:0000000011278152
DTC DETECTION LOGIC
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
ETC MOT-B1
(Throttle actuator control motor current
range/performance)
P2118
ECM detects short in both circuits between ECM and throttle control motor.
POSSIBLE CAUSE
Harness or connectors (Throttle control motor circuit is shorted.)
Electric throttle control actuator (Throttle control motor)
FAIL-SAFE
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx.
5 degrees) by the return spring.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 2 seconds.
2. Start engine and let it idle for 5 seconds.
3. Check DTC.
Is DTC detected?
YES >> Proceed to EC-439, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
L
INFOID:0000000011278153
1.CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT
1.
2.
3.
4.
Electric throttle control actuator
ECM
Connector
Terminal
Connector
5
F50
F51
6
5.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
O
Continuity
Terminal
1
Existed
Not existed
Not existed
Existed
Also check harness for short to ground and to power.
Revision: August 2014
EC-439
2015 Rogue NAM
P2118 THROTTLE CONTROL MOTOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.CHECK THROTTLE CONTROL MOTOR
Check the throttle control motor. Refer to EC-440, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278154
1.CHECK THROTTLE CONTROL MOTOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Check the resistance between electric throttle control actuator terminals as per the following.
Electric throttle control actuator
+
Resistance
(Approx.)
1 - 15 [at 25C (77F)]
Terminals
5
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-440
2015 Rogue NAM
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC Description
A
INFOID:0000000011278155
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
ETC ACTR-B1
(Throttle actuator control throttle body
range/performance)
P2119
EC
DTC detecting condition
Electric throttle control actuator does not function properly due to the
return spring malfunction.
Throttle valve opening angle in fail-safe mode is not in specified range.
ECM detect the throttle valve is stuck open.
POSSIBLE CAUSE
Electric throttle control actuator
FAIL-SAFE
Traveling control mode (Engine output control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B
1. Turn ignition switch ON and wait at least 1 second.
2. Set selector lever to D position and wait at least 3 seconds.
3. Set selector lever to P position.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Turn ignition switch ON and wait at least 1 second.
6. Set selector lever to D position and wait at least 3 seconds.
7. Set selector lever to P position.
8. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
9. Check DTC.
Is DTC detected?
YES >> Proceed to EC-441, "Diagnosis Procedure".
NO
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1. Turn ignition switch ON and wait at least 1 second.
2. Set selector lever to D position and wait at least 3 seconds.
3. Set selector lever to P position.
4. Start engine and let it idle for 3 seconds.
5. Check DTC.
Is DTC detected?
YES >> Proceed to EC-441, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278156
1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Remove the intake air duct. Refer to EM-26, "Exploded View".
Revision: August 2014
EC-441
2015 Rogue NAM
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Check if foreign matter is caught between the throttle valve and the housing.
Is the inspection result normal?
YES >> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
NO
>> Remove the foreign matter and clean the electric throttle control actuator inside, then perform
throttle valve closed position learning. Refer to EC-143, "Work Procedure".
Revision: August 2014
EC-442
2015 Rogue NAM
P2122, P2123 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2122, P2123 APP SENSOR
DTC Description
INFOID:0000000011278157
DTC DETECTION LOGIC
DTC No.
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2122
APP SEN 1/CIRC
(Throttle/pedal position sensor/switch D
circuit low)
An excessively low voltage from the APP sensor 1 is sent to ECM.
P2123
APP SEN 1/CIRC
(Throttle/pedal position sensor/switch D
circuit high)
An excessively high voltage from the APP sensor 1 is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (APP sensor 1 circuit is open or shorted.)
Accelerator pedal position sensor (APP sensor 1)
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
1.CHECK DTC PRIORITY
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
N
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-443, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278158
1.CHECK DTC PRIORITY
If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
Revision: August 2014
EC-443
2015 Rogue NAM
P2122, P2123 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK APP SENSOR 1 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.
+
Voltage
(Approx.)
Ground
5V
APP sensor
Connector
Terminal
E25
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
122
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK APP SENSOR 1 GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
127
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK APP SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
126
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
Revision: August 2014
EC-444
2015 Rogue NAM
P2122, P2123 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.CHECK APP SENSOR
Check the APP sensor. Refer to EC-445, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
EC
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278159
1.CHECK ACCELERATOR PEDAL POSITION SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following condition.
ECM
Sensor 1
Connector
Voltage
Terminal
126
127
E16
Sensor 2
Condition
Accelerator pedal
119
120
Fully released
0.5 - 1.0 V
Fully depressed
4.2 - 4.8 V
Fully released
0.25 - 0.5 V
Fully depressed
2.0 - 2.5 V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
Revision: August 2014
EC-445
2015 Rogue NAM
P2127, P2128 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2127, P2128 APP SENSOR
DTC Description
INFOID:0000000011278160
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
DTC detecting condition
P2127
APP SEN 2/CIRC
(Throttle/pedal position sensor/switch E
circuit low)
An excessively low voltage from the APP sensor 2 is sent to ECM.
P2128
APP SEN 2/CIRC
(Throttle/pedal position sensor/switch E
circuit high)
An excessively high voltage from the APP sensor 2 is sent to ECM.
POSSIBLE CAUSE
Harness or connectors (APP sensor 2 circuit is open or shorted.)
Accelerator pedal position sensor (APP sensor 2)
Sensor power supply 2 circuit
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-446, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278161
1.CHECK APP SENSOR 2 POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.
+
APP sensor
Connector
Terminal
E25
Revision: August 2014
Voltage
(Approx.)
Ground
5V
EC-446
2015 Rogue NAM
P2127, P2128 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
EC
Perform EC-487, "Diagnosis Procedure".
Is inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK APP SENSOR 2 GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
E
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
120
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT
1.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
119
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts
5.CHECK APP SENSOR
Check the APP sensor. Refer to EC-447, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
Refer to GI-44, "Intermittent Incident".
6.CHECK INTERMITTENT INCIDENT
>> INSPECTION END
Component Inspection
INFOID:0000000011278162
1.CHECK ACCELERATOR PEDAL POSITION SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following condition.
Revision: August 2014
EC-447
2015 Rogue NAM
P2127, P2128 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Sensor 1
Connector
Voltage
Terminal
126
Fully released
127
E16
Sensor 2
Condition
Accelerator pedal
119
120
0.5 - 1.0 V
Fully depressed
4.2 - 4.8 V
Fully released
0.25 - 0.5 V
Fully depressed
2.0 - 2.5 V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
Revision: August 2014
EC-448
2015 Rogue NAM
P2135 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2135 TP SENSOR
DTC Description
INFOID:0000000011278163
DTC DETECTION LOGIC
DTC No.
P2135
EC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
TP SENSOR-B1
(Throttle/pedal position sensor/switch A /
B voltage correlation)
Rationally incorrect voltage is sent to ECM compared with the signals from
TP sensor 1 and TP sensor 2.
POSSIBLE CAUSE
Harness or connectors (TP sensor 1 or 2 circuit is open or shorted.)
Electric throttle control actuator (TP sensor 1 or 2)
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
1.CHECK DTC PRIORITY
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-449, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278164
1.CHECK DTC PRIORITY
If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
2.CHECK THROTTLE POSITION SENSOR POWER SUPPLY
1.
2.
Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Revision: August 2014
EC-449
2015 Rogue NAM
P2135 TP SENSOR
< DTC/CIRCUIT DIAGNOSIS >
3. Turn ignition switch ON.
4. Check the voltage between electric throttle control actuator harness connector and ground.
[QR25DE]
Voltage
(Approx.)
Ground
5V
Electric throttle control actuator
Connector
Terminal
F50
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ground.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
80
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F50
F52
78
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between electric throttle control actuator harness connector and ECM harness connector.
+
Electric throttle control actuator
ECM
Connector
F50
Terminal
1
3
Revision: August 2014
Connector
F52
Continuity
Terminal
79
77
Existed
EC-450
2015 Rogue NAM
P2135 TP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK THROTTLE POSITION SENSOR
EC
Check the throttle position sensor. Refer to EC-451, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
E
>> INSPECTION END
Component Inspection
INFOID:0000000011278165
1.CHECK THROTTLE POSITION SENSOR
1.
2.
3.
4.
5.
6.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Perform Throttle Valve Closed Position Learning. Refer to EC-143, "Work Procedure".
Turn ignition switch ON.
Set selector lever to D position.
Check the voltage between ECM harness connector terminals as per the following conditions.
ECM
Connector
Sensor 1
Condition
Voltage
Terminal
79
F52
Sensor 2
78
77
Accelerator
pedal
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to EM-29, "Removal and Installation".
Revision: August 2014
EC-451
2015 Rogue NAM
P2138 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2138 APP SENSOR
DTC Description
INFOID:0000000011278166
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
APP SENSOR
(Throttle/pedal position sensor/switch D /
E voltage correlation)
Rationally incorrect voltage is sent to ECM compared with the signals from
APP sensor 1 and APP sensor 2.
DTC No.
P2138
POSSIBLE CAUSE
Harness or connectors (APP sensor 1 or 2 circuit is open or shorted.)
Accelerator pedal position sensor (APP sensor 1 or 2)
Sensor power supply 2 circuit
FAIL-SAFE
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle
position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the
acceleration will be poor.
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >> Proceed to EC-452, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278167
1.CHECK DTC PRIORITY
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-382, "DTC Description".
NO
>> GO TO 2.
2.CHECK APP SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
Revision: August 2014
EC-452
2015 Rogue NAM
P2138 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Disconnect accelerator pedal position (APP) sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between APP sensor harness connector and ground.
EC
Voltage
(Approx.)
Ground
5V
APP sensor
Connector
Terminal
E25
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
F
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
122
Existed
4. Also check harness for short to ground.
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.CHECK APP SENSOR 2 POWER SUPPLY
Check the voltage between APP sensor harness connector and ground.
+
APP sensor
Connector
Terminal
E25
Voltage
(Approx.)
Ground
5V
Is the inspection result normal?
YES >> GO TO 6.
NO
>> GO TO 5.
5.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform EC-487, "Diagnosis Procedure".
Is inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
6.CHECK APP SENSOR GROUND CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
Revision: August 2014
EC-453
2015 Rogue NAM
P2138 APP SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
APP sensor
ECM
Connector
Terminal
Connector
E25
Terminal
120
E16
Continuity
Existed
127
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
7.CHECK APP SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Connector
Terminal
Connector
E25
Terminal
126
E16
Continuity
119
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Repair or replace error-detected parts
8.CHECK APP SENSOR
Check the APP sensor. Refer to EC-454, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
9.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Component Inspection
INFOID:0000000011278168
1.CHECK ACCELERATOR PEDAL POSITION SENSOR
1.
2.
3.
4.
Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following condition.
ECM
Sensor 1
Connector
Voltage
Terminal
126
Fully released
127
E16
Sensor 2
Condition
Accelerator pedal
119
120
0.5 - 1.0 V
Fully depressed
4.2 - 4.8 V
Fully released
0.25 - 0.5 V
Fully depressed
2.0 - 2.5 V
Is the inspection result normal?
Revision: August 2014
EC-454
2015 Rogue NAM
P2138 APP SENSOR
< DTC/CIRCUIT DIAGNOSIS >
YES >> INSPECTION END
NO
>> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".
[QR25DE]
A
EC
Revision: August 2014
EC-455
2015 Rogue NAM
P2610 ECM INTERNAL TIMER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
P2610 ECM INTERNAL TIMER
Description
INFOID:0000000011278169
This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch
ON. This enables the judging of the state of engine cooling at an engine start.
DTC Description
INFOID:0000000011278170
DTC DETECTION LOGIC
CONSULT screen terms
(Trouble diagnosis content)
DTC No.
P2610
ECM/PCM INTERNAL ENG OFF TIMER
(ECM/PCM internal engine off timer performance)
DTC detecting condition
ECM internal engine off timer is malfunctioning.
The time calculated by ECM based on a descent allowance of engine
coolant temperatures during ignition switch OFF is extremely shorter
than the time counted by the Engine internal OFF timer.
POSSIBLE CAUSE
ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
It is necessary to erase permanent DTC?
YES >> GO TO 4.
NO
>> GO TO 2.
2.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 12 V or more under ignition
switch OFF condition.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-I
1. Turn ignition switch ON and wait at least 190 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-457, "Diagnosis Procedure".
NO
>> INSPECTION END
4.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 12 V or more under ignition switch OFF condition.
Before performing the following procedure, check that fuel level is between 2/8 and 7/8.
>> GO TO 5.
Revision: August 2014
EC-456
2015 Rogue NAM
P2610 ECM INTERNAL TIMER
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
5.PERFORM DTC CONFIRMATION PROCEDURE-I
1. Turn ignition switch ON and wait at least 190 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-457, "Diagnosis Procedure".
NO
>> GO TO 6.
EC
6.PERFORM DTC CONFIRMATION PROCEDURE-II
CAUTION:
To start this self-diagnosis, the conditions listed bellow are required to be satisfied. Perform the following steps to satisfy the conditions.
Engine coolant temperature decrease by 55C (131F) or more during the time between an ignition
switch OFF (after engine warm-up) and the second ignition switch ON.
A fuel temperature at the second ignition switch ON is 5C (23F) or more and less than 35C (95F).
The temperature difference between engine coolant and fuel is 5C (41F) or more.
NOTE:
This self-diagnosis is not performed if the distance traveled is extremely short.
1. Turn ignition switch ON.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and soak the vehicle for at least 12 hours.
CAUTION:
Never turn ON the ignition switch during soaking.
Never open the fuel filler cap and perform refueling during soaking.
4. Turn ignition switch ON and wait at least 190 seconds.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-457, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278171
1.CHECK SELF-DIAGNOSTIC RESULT
check that DTCs related to the fuel system and the cooling system are not detected.
Is the inspection result normal?
YES >> Check the DTC. Refer to EC-69, "CONSULT Function".
NO
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Erase DTC.
2. Perform DTC Confirmation Procedure again. Refer to EC-456, "DTC Description".
Is the 1st trip DTC P2610 displayed again?
YES >> Replace ECM. Refer to EC-502, "Removal and Installation".
NO
>> INSPECTION END
Revision: August 2014
EC-457
2015 Rogue NAM
BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
BRAKE PEDAL POSITION SWITCH
Component Function Check
INFOID:0000000011278172
1.CHECK BRAKE PEDAL POSITION SWITCH FUNCTION
1.
2.
3.
With CONSULT
Turn ignition switch ON.
Select BRAKE SW1 in DATA MONITOR mode with CONSULT.
Check BRAKE SW1 indication as per the following conditions.
Monitor item
Condition
BRAKE SW1
1.
2.
Brake pedal
Indication
Slightly depressed
OFF
Fully released
ON
Without CONSULT
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals.
ECM
+
Connector
Condition
Voltage
Terminal
E16
116
128
Slightly depressed
Brake pedal
Fully released
Approx. 0 V
Battery voltage
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-458, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278173
1.CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect brake pedal position switch harness connector.
Turn ignition switch ON.
Check the voltage between brake pedal position switch harness connector and ground.
+
Brake pedal position switch
Connector
Terminal
E6
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect fuse block (J/B) harness connector.
Check the continuity between brake pedal position switch harness connector and fuse block (J/B) harness
connector.
+
Brake pedal position switch
Fuse block (J/B)
Connector
Terminal
Connector
Terminal
E6
M68
16R
Revision: August 2014
Continuity
Existed
E C -4 5 8
2015 Rogue NAM
BRAKE PEDAL POSITION SWITCH
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between brake pedal position switch harness connector and ECM harness connector.
+
Brake pedal position switch
ECM
Terminal
Connector
Terminal
E6
E16
116
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.CHECK BRAKE PEDAL POSITION SWITCH
Check brake pedal position switch. Refer to EC-459, "Component Inspection (Brake Pedal Position Switch)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace brake pedal position switch. Refer to BR-20, "Exploded View".
Component Inspection (Brake Pedal Position Switch)
INFOID:0000000011278174
1.CHECK BRAKE PEDAL POSITION SWITCH-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect brake pedal position harness connector.
Check the continuity between brake pedal position switch terminals as per the following conditions.
Condition
L
Fully released
2
Brake pedal
Slightly depressed
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK BRAKE PEDAL POSITION SWITCH-2
1.
2.
Continuity
Terminals
1
Brake pedal position switch
+
Continuity
Connector
EC
Adjust brake pedal position switch installation. Refer to BR-15, "Adjustment".
Check the continuity between brake pedal position switch terminals as per the following conditions.
Brake pedal position switch
Condition
Continuity
Terminals
Fully released
1
Brake pedal
Slightly depressed
Existed
Not existed
Is the inspection result normal?
Revision: August 2014
EC-459
2015 Rogue NAM
BRAKE PEDAL POSITION SWITCH
< DTC/CIRCUIT DIAGNOSIS >
YES >> INSPECTION END
NO
>> Replace brake pedal position switch. Refer to BR-20, "Exploded View".
Revision: August 2014
EC-460
[QR25DE]
2015 Rogue NAM
COOLING FAN
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
COOLING FAN
Component Function Check
INFOID:0000000011278175
1.CHECK COOLING FAN FUNCTION
EC
With CONSULT
1. Turn ignition switch ON.
2. Perform FAN DUTY CONTROL in ACTIVE TEST mode with CONSULT.
3. Make sure that cooling fan speed varies according to the percentage.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-461, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278176
1.CHECK COOLING FAN RELAY POWER SUPPLY CIRCUIT
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect cooling fan relays-2, -3.
Turn ignition switch ON.
Check the voltage between cooling fan relays-2, -3 harness connectors and ground.
+
Cooling fan relay
Connector
Voltage
Ground
Battery voltage
Terminal
H-2
(cooling fan relay-2)
H-3
(cooling fan relay-3)
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Perform trouble diagnosis for power supply circuit.
2.CHECK COOLING FAN MOTOR CIRCUIT-1
Check the voltage between cooling fan relays-2, -3 harness connectors and ground.
L
+
Cooling fan relay
Connector
Voltage
Terminal
H-2
(cooling fan relay-2)
H-3
(cooling fan relay-3)
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 4.
3.CHECK COOLING FAN RELAY OUTPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connectors.
Check the continuity between cooling fan relay-2, -3 harness connectors and IPDM E/R harness connector.
Revision: August 2014
EC-461
2015 Rogue NAM
COOLING FAN
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Cooling fan relay
IPDM E/R
Connector
Terminal
Connector
F42
H-2
(cooling fan relay-2)
Continuity
Terminal
107
H-3
(cooling fan relay-3)
Existed
106
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
4.CHECK COOLING FAN MOTOR POWER SUPPLY CIRCUIT
1.
2.
Disconnect cooling fan motor-1 harness connector.
Check the voltage between cooling fan motor-1 harness connector and ground.
+
Voltage
Ground
Battery voltage
Cooling fan motor-1
Connector
Terminal
1
F3
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Perform trouble diagnosis for power supply circuit.
5.CHECK COOLING FAN MOTOR CIRCUIT-2
1.
Check the continuity between cooling fan relay-2, -3 harness connectors and cooling fan motor-1, -2 harness connectors.
+
Cooling fan relay
Cooling fan motor-1
Connector
Terminal
Connector
Continuity
Terminal
3
H-2
(cooling fan relay-2)
3
F3
H-3
(cooling fan relay-3)
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 11.
NO
>> Repair or replace error-detected parts.
6.CHECK COOLING FAN MOTOR CIRCUIT-3
1.
Check the continuity between IPDM E/R harness connector and cooling fan motor-2 harness connector.
+
IPDM E/R
Cooling fan motor-2
Connector
Terminal
Connector
F41
85
F5
Revision: August 2014
Continuity
Terminal
1
2
EC-462
Existed
2015 Rogue NAM
COOLING FAN
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
7.CHECK COOLING FAN MOTOR CIRCUIT-4
1.
EC
Check the continuity between cooling fan relay-3 harness connectors and ground.
C
+
Cooling fan relay-3
Connector
Terminal
H-3
Continuity
D
Ground
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.CHECK COOLING FAN MOTOR CIRCUIT-5
1.
Check the continuity between cooling fan relay--3 harness connectors and cooling fan motor-2 harness
connector.
+
Cooling fan relay-2
Cooling fan motor-2
Connector
Terminal
Connector
H-2
F5
Continuity
Terminal
1
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.CHECK COOLING FAN MOTOR CIRCUIT-4
1.
Check the continuity between cooling fan motor-2 harness connector and ground.
L
+
Cooling fan motor-2
Connector
Continuity
Ground
Existed
Terminal
F5
3
4
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 10.
NO
>> Repair or replace error-detected parts.
10.CHECK COOLING FAN RELAY-2 AND -3
Refer to EC-464, "Component Inspection (Cooling Fan Relay)".
Is the inspection result normal?
YES >> GO TO 11.
NO
>> Replace malfunctioning cooling fan relay.
11.CHECK COOLING FAN MOTORS-1 AND -2
Refer to EC-464, "Component Inspection (Cooling Fan Motor)".
Revision: August 2014
EC-463
2015 Rogue NAM
COOLING FAN
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Replace malfunctioning cooling fan motor. Refer to CO-17, "Removal and Installation".
12.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-40, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Component Inspection (Cooling Fan Motor)
INFOID:0000000011278177
1.CHECK COOLING FAN MOTOR
1.
2.
3.
Turn ignition switch OFF.
Disconnect cooling fan motor harness connector.
Supply cooling fan motor terminals with battery voltage and check operation.
Cooling fan motor
Terminal
Condition
3 and 4
3 and 4
1 and 2
1 and 2
1, 2
3, 4
Check that cooling fan speed of condition B is higher than that of A.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace cooling fan motor. Refer to CO-17, "Removal and Installation".
Component Inspection (Cooling Fan Relay)
INFOID:0000000011278178
1.CHECK COOLING FAN RELAYS
1.
2.
3.
Turn ignition switch OFF.
Remove cooling fan relay-2, -3.
Check the continuity between cooling fan relay-2, -3 terminals as per the following conditions.
Cooling fan relay-2, -3
Conditions
Continuity
Terminal
3
12V direct current supply between terminals 1 and 2
No current supply
Existed
Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace cooling fan relay.
Revision: August 2014
EC-464
2015 Rogue NAM
ELECTRICAL LOAD SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ELECTRICAL LOAD SIGNAL
Description
INFOID:0000000011278179
The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred via EC
the CAN communication.
Component Function Check
INFOID:0000000011278180
1.CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION
1.
2.
3.
Turn ignition switch ON.
Connect CONSULT and select DATA MONITOR mode.
Select LOAD SIGNAL and check indication under the following conditions.
Monitor item
LOAD SIGNAL
Condition
Rear window defogger switch
Indication
ON
ON
OFF
OFF
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Proceed to EC-465, "Diagnosis Procedure".
2.CHECK LIGHTING SWITCH FUNCTION
Check LOAD SIGNAL indication under the following conditions.
Monitor item
LOAD SIGNAL
Condition
Lighting switch
Indication
ON at 2nd position
ON
OFF
OFF
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Proceed to EC-465, "Diagnosis Procedure".
3.CHECK HEATER FAN CONTROL SWITCH FUNCTION
Select HEATER FAN SW and check indication under the following conditions.
Monitor item
HEATER FAN SW
Condition
Heater fan control switch
Indication
ON
ON
OFF
OFF
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-465, "Diagnosis Procedure".
Diagnosis Procedure
N
INFOID:0000000011278181
1.INSPECTION START
Confirm the malfunctioning circuit (rear window defogger, headlamp or heater fan). Refer to EC-465, "Component Function Check".
Which circuit is related to the incident?
Rear window defogger>>GO TO 2.
Headlamp>>GO TO 3.
Heater fan>>GO TO 4.
2.CHECK REAR WINDOW DEFOGGER SYSTEM
Check rear window defogger system. Refer to DEF-21, "Work Flow".
Revision: August 2014
EC-465
2015 Rogue NAM
ELECTRICAL LOAD SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
>> INSPECTION END
3.CHECK HEADLAMP SYSTEM
Check headlamp system. Refer to EXL-81, "Work Flow" (with halogen headlamp) or EXL-218, "Work Flow"
(with LED headlamp).
>> INSPECTION END
4.CHECK HEATER FAN CONTROL SYSTEM
Check heater fan control system. Refer to HAC-46, "Work Flow" (with automatic air conditioner) or HAC-147,
"Work Flow" (with manual air conditioner).
>> INSPECTION END
Revision: August 2014
EC-466
2015 Rogue NAM
FUEL INJECTOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
FUEL INJECTOR
Component Function Check
INFOID:0000000011278182
1.INSPECTION START
EC
Turn ignition switch to START.
Are any cylinders ignited?
YES >> GO TO 2.
NO
>> Proceed to EC-467, "Diagnosis Procedure".
2.CHECK FUEL INJECTOR FUNCTION
With CONSULT
Start engine.
Perform POWER BALANCE in ACTIVE TEST mode with CONSULT.
Check that each circuit produces a momentary engine speed drop.
Without CONSULT
1. Start engine.
2. Listen to each fuel injector operating sound.
1.
2.
3.
Clicking sound should be heard.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-467, "Diagnosis Procedure".
PBIB3332E
Diagnosis Procedure
INFOID:0000000011278183
1.CHECK FUEL INJECTOR POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel injector harness connector.
Turn ignition switch ON.
Check the voltage between fuel injector harness connector and ground.
L
+
Fuel injector
Cylinder
Connector
Terminal
F11
F12
F14
F13
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK FUEL INJECTOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between fuel injector harness connector and IPDM E/R harness connector.
Revision: August 2014
EC-467
2015 Rogue NAM
FUEL INJECTOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Fuel injector
IPDM E/R
Cylinder
Connector
Terminal
F11
F12
F14
F13
Continuity
Connector
Terminal
E121
43
Existed
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.CHECK FUEL INJECTOR OUTPUT SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between fuel injector harness connector and ECM harness connector.
+
Fuel injector
ECM
Cylinder
Connector
Terminal
F11
F12
F14
F13
Connector
Continuity
Terminal
13
F51
14
10
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.CHECK FUEL INJECTOR
Check fuel injector. Refer to EC-468, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Replace malfunctioning fuel injector. Refer to EM-45, "Exploded View".
5.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-40, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Component Inspection
INFOID:0000000011278184
1.CHECK FUEL INJECTOR
1.
2.
Turn ignition switch OFF.
Disconnect fuel injector harness connector.
Revision: August 2014
EC-468
2015 Rogue NAM
FUEL INJECTOR
< DTC/CIRCUIT DIAGNOSIS >
3. Check resistance between fuel injector terminals as per the following.
[QR25DE]
A
Fuel injector
+
EC
Resistance
11.1 - 14.5 [at 10 - 60C (50 - 140F)]
Terminal
1
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace malfunctioning fuel injector. Refer to EM-45,
"Removal and Installation".
C
PBIA9579J
Revision: August 2014
EC-469
2015 Rogue NAM
FUEL PUMP
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
FUEL PUMP
Description
INFOID:0000000011278185
Sensor
Input signal to ECM
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
Battery
Battery voltage*
ECM Function
Actuator
Fuel pump control
Fuel pump relay
Fuel pump
*: ECM determines the start signal status by the signals of engine speed and battery voltage.
The ECM activates the fuel pump for several seconds after the ignition switch is turned ON to improve engine
start ability. If the ECM receives a engine speed signal from the camshaft position sensor (PHASE), it knows
that the engine is rotating, and causes the pump to operate. If the engine speed signal is not received when
the ignition switch is ON, the engine stalls. The ECM stops pump operation and prevents battery discharging,
thereby improving safety. The ECM does not directly drive the fuel pump. It controls the ON/OFF fuel pump
relay, which in turn controls the fuel pump.
Condition
Fuel pump operation
Ignition switch is turned to ON.
Operates for 1 second.
Engine running and cranking
Operates.
When engine is stopped
Stops in 1.5 seconds.
Except as shown above
Stops.
Component Function Check
INFOID:0000000011278186
1.CHECK FUEL PUMP FUNCTION
1.
2.
Turn ignition switch ON.
Pinch fuel feed hose with two fingers.
Fuel pressure pulsation should be felt on the fuel feed
hose for 1 second after ignition switch is turned ON.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-470, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278187
1.CHECK FUEL PUMP RELAY CONTROL SIGNAL
1.
2.
Turn ignition switch ON.
Check the voltage between ECM harness connector.
ECM
+
Voltage
Connector
Terminal
Connector
Terminal
F51
18
E16
128
Battery voltage should exist 1 second after
ignition switch is turn ON.
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK FUEL PUMP RELAY CONTROL SIGNAL CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Revision: August 2014
EC-470
2015 Rogue NAM
FUEL PUMP
< DTC/CIRCUIT DIAGNOSIS >
4. Check the continuity between ECM harness connector and IPDM E/R harness connector.
[QR25DE]
A
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F51
18
F35
76
EC
Existed
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
3.CHECK FUEL PUMP POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Turn ignition switch ON.
Check the voltage between fuel level sensor unit and fuel pump harness connector and ground.
+
Fuel level sensor unit
and fuel pump
Connector
Terminal
B103
Voltage
Ground
Battery voltage should exist 1 second
after ignition switch is turn ON.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> GO TO 4.
4.CHECK FUEL PUMP POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between IPDM E/R harness connector and fuel level sensor unit and fuel pump
harness connector.
+
IPDM E/R
Fuel level sensor unit and
fuel pump
Connector
Terminal
Connector
Terminal
E121
46
B103
Continuity
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace error-detected parts.
5.CHECK FUEL PUMP GROUND CIRCUIT
1.
Check the continuity between fuel level sensor unit and fuel pump and ground.
P
+
Fuel level sensor unit and fuel pump
Connector
Terminal
B103
Continuity
Ground
Existed
2. Also heck harness for short to power.
Is the inspection result normal?
Revision: August 2014
EC-471
2015 Rogue NAM
FUEL PUMP
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 6.
NO
>> Repair or replace error-detected parts.
[QR25DE]
6.CHECK FUEL PUMP
Refer to EC-472, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
7.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-40, "Removal and Installation".
NO
>> Repair or replace harness or connectors.
Component Inspection
INFOID:0000000011278188
1.CHECK FUEL PUMP
1.
2.
3.
Turn ignition switch OFF.
Disconnect fuel level sensor unit and fuel pump harness connector.
Check resistance between fuel level sensor unit and fuel pump terminals as follows.
Fuel level sensor unit and fuel pump
+
Resistance
0.2 - 5.0 [at 25C (77F)]
Terminal
6
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace fuel level sensor unit and fuel pump. Refer to FL-5, "Removal and Installation".
Revision: August 2014
EC-472
2015 Rogue NAM
IGNITION SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
IGNITION SIGNAL
Component Function Check
INFOID:0000000011278189
1.INSPECTION START
EC
Turn ignition switch OFF, and restart engine.
Does the engine start?
YES-1 >> With CONSULT: GO TO 2.
YES-2 >> Without CONSULT: GO TO 3.
NO
>> Proceed to EC-473, "Diagnosis Procedure".
2.CHECK IGNITION SIGNAL FUNCTION
With CONSULT
1. Perform POWER BALANCE in ACTIVE TEST mode with CONSULT.
2. Check that each circuit produces a momentary engine speed drop.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-473, "Diagnosis Procedure".
3.CHECK IGNITION SIGNAL FUNCTION
Without CONSULT
1. Let engine idle.
2. Read the voltage signal between ECM harness connector terminals with an oscilloscope.
H
ECM
+
Connector
Terminal
Voltage signal
Connector
Terminal
86
87
F52
90
E16
128
91
JMBIA0035GB
NOTE:
The pulse cycle changes depending on rpm at idle.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-473, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278190
1.CHECK ECM POWER SUPPLY
1.
2.
Turn ignition switch OFF, wait at least 10 seconds and then turn it ON.
Check the voltage between ECM harness connector terminals.
ECM
E16
Connector
Voltage
128
Battery voltage
Terminal
121
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Refer to EC-168, "Diagnosis Procedure".
Revision: August 2014
EC-473
2015 Rogue NAM
IGNITION SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
2.CHECK CONDENSER POWER SUPPLY
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect joint connector-F01 harness connector.
Turn ignition switch ON.
Check the voltage between joint connector-F01 harness connector and ground.
+
Joint connector-F01
Connector
Terminal
F8
Voltage
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 4.
NO
>> GO TO 3.
3.CHECK CONDENSER POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect IPDM E/R harness connector.
Check the continuity between IPDM E/R harness connector and joint connector-F01 harness connector.
+
IPDM E/R
Joint connector-F01
Connector
Terminal
Connector
Terminal
F35
66
F8
Continuity
Existed
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> Refer to EC-168, "Diagnosis Procedure".
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.CHECK CONDENSER GROUND CIRCUIT
1.
2.
Turn ignition switch OFF.
Check the continuity between joint connector-F01 harness connector and ground.
+
Joint connector-F01
Connector
Terminal
F8
Voltage
Ground
Existed
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair open circuit or short to power in harness or connectors.
5.CHECK CONDENSER
Check condenser. Refer to EC-477, "Component Inspection (Condenser)"
Is the inspection result normal?
YES >> GO TO 6.
NO
>> Replace condenser.
6.CHECK IGNITION COIL POWER SUPPLY
1.
2.
3.
4.
Reconnect all harness connectors disconnected.
Disconnect ignition coil harness connector.
Turn ignition switch ON.
Check the voltage between ignition coil harness connector and ground.
Revision: August 2014
EC-474
2015 Rogue NAM
IGNITION SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Ignition coil
Cylinder
Connector
Terminal
F47
F46
F48
F49
Voltage
EC
Ground
Battery voltage
Is the inspection result normal?
YES >> GO TO 7.
NO
>> Repair or replace harness or connectors.
7.CHECK IGNITION COIL GROUND CIRCUIT
1.
2.
Turn ignition switch OFF.
Check the continuity between ignition coil harness connector and ground.
F
+
Ignition coil
Cylinder
Connector
Terminal
F47
F46
F48
F49
Continuity
Ground
Existed
3. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 8.
NO
>> Repair open circuit or short to power in harness or connectors.
8.CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT
1.
2.
Disconnect ECM harness connector.
Check the continuity between ignition coil harness connector and ECM harness connector.
+
Ignition coil
ECM
Cylinder
Connector
Terminal
F47
F46
F48
F49
Connector
L
Continuity
Terminal
86
F52
87
90
Existed
91
3. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 9.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
9.CHECK IGNITION COIL WITH POWER TRANSISTOR
Check ignition coil with power transistor. Refer to EC-476, "Component Inspection (Ignition Coil with Power
Transistor)".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-44, "Intermittent Incident".
NO
>> Replace malfunctioning ignition coil with power transistor. Refer to EM-41, "Removal and Installation".
Revision: August 2014
EC-475
2015 Rogue NAM
IGNITION SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Component Inspection (Ignition Coil with Power Transistor)
INFOID:0000000011278191
1.CHECK IGNITION COIL WITH POWER TRANSISTOR-1
1.
2.
3.
Turn ignition switch OFF.
Disconnect ignition coil harness connector.
Check resistance between ignition coil terminals as per the following.
Ignition coil
+
Resistance [at 25C (77F)]
Terminal No. (Polarity)
1
2
2
3
3
Except 0 or
Except 0
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Replace malfunctioning ignition coil with power transistor. Refer to EM-41, "Removal and Installation".
2.CHECK IGNITION COIL WITH POWER TRANSISTOR-2
CAUTION:
Perform the following procedure in a place with no combustible objects and good ventilation.
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Remove fuel pump fuse in IPDM E/R to release fuel pressure.
NOTE:
Do not use CONSULT to release fuel pressure, or fuel pressure applies again during the following procedure.
4. Start engine.
5. After engine stalls, crank it 2 or 3 times to release all fuel pressure.
6. Turn ignition switch OFF.
7. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.
8. Remove ignition coil and spark plug of the cylinder to be checked.
9. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.
10. Connect spark plug and harness connector to ignition coil.
11. Fix ignition coil using a rope etc. with gap of 13 - 17 mm (0.52 0.66 in) between the edge of the spark plug and grounded metal
portion as shown in the figure.
12. Crank engine for approximately 3 seconds, and check whether
spark is generated between the spark plug and the grounded
metal portion.
Spark should be generated.
CAUTION:
During the operation, always stay 0.5 m (19.7 in) or more
JMBIA0066GB
away from the spark plug and the ignition coil. Be careful
not to get an electrical shock while checking, because the
electrical discharge voltage becomes 20 kV or more.
It might cause to damage the ignition coil if the gap of more than 17 mm (0.66 in) is taken.
NOTE:
When the gap is less than 13 mm (0.52 in), the spark might be generated even if the coil is malfunctioning.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace malfunctioning ignition coil with power transistor. Refer to EM-41, "Removal and Installation".
Revision: August 2014
EC-476
2015 Rogue NAM
IGNITION SIGNAL
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Component Inspection (Condenser)
INFOID:0000000011278192
1.CHECK CONDENSER
1.
2.
3.
Turn ignition switch OFF.
Disconnect joint connector-F01 harness connector.
Check resistance between joint connector terminals as per the following.
EC
Joint connector-F01
+
Resistance
Above 1 M [at 25C (77C)]
Terminal
1
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace condenser.
Revision: August 2014
EC-477
2015 Rogue NAM
INFORMATION DISPLAY (ASCD)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
INFORMATION DISPLAY (ASCD)
Component Function Check
INFOID:0000000011278193
1.CHECK INFORMATION DISPLAY
1.
2.
3.
Start engine.
Press ASCD MAIN switch on ASCD steering switch.
Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
4. Press SET/ switch.
5. Check that the reading of the speedometer shows the same value as the set speed indicated in the information display while driving the vehicle on a flat road.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-478, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000011278194
1.CHECK DTC
Check that DTC UXXXX, P0500 or P1574 is not displayed.
Is the inspection result normal?
YES >> GO TO 2.
NO-1 >> Perform trouble diagnosis for DTC UXXXX.
NO-2 >> Perform trouble diagnosis for DTC P0500. Refer to EC-353, "DTC Description".
NO-3 >> Perform trouble diagnosis for DTC P1574. Refer to EC-417, "DTC Description".
2.CHECK DTC WITH COMBINATION METER
Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Perform trouble diagnosis for DTC indicated.
3.CHECK INTERMITTENT INCIDENT
Perform GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-84, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-478
2015 Rogue NAM
MALFUNCTION INDICATOR LAMP
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
MALFUNCTION INDICATOR LAMP
Component Function Check
A
INFOID:0000000011278195
1.CHECK MIL FUNCTION
EC
1. Turn ignition switch ON.
2. Check that MIL illuminates.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-479, "Diagnosis Procedure".
Diagnosis Procedure
D
INFOID:0000000011278196
1.CHECK DTC
Check that DTC UXXXX is not displayed.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Perform trouble diagnosis for DTC UXXXX.
2.CHECK COMBINATION METER FUNCTION
Check combination meter function. Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace.
3.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-84, "Removal and Installation".
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-479
2015 Rogue NAM
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
Component Function Check
INFOID:0000000011278197
1.CHECK ORVR FUNCTION
Check whether the following symptoms are present.
Fuel odor from EVAP canister is strong.
Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.
Are any symptoms present?
YES >> Proceed to EC-480, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278198
1.INSPECTION START
Check whether the following symptoms are present.
A: Fuel odor from EVAP canister is strong.
B: Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.
A or B
A
>> GO TO 2.
B
>> GO TO 7.
2.CHECK EVAP CANISTER
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached. Refer to FL-19, "Removal and Installation".
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 4.
3.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
Check if water will drain from EVAP canister
Does water drain from the EVAP canister?
YES >> GO TO 4.
NO
>> GO TO 6.
JMBIA1134GB
4.REPLACE EVAP CANISTER
Replace EVAP canister with a new one. Refer to FL-19, "Removal and Installation".
>> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the EVAP hose between EVAP canister and vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose. Refer to FL-11, "FWD : Removal and Installation" (with FWD models) or FL-15, "AWD : Removal and Installation" (with AWD models).
6.CHECK REFUELING EVAP VAPOR CUT VALVE
Revision: August 2014
EC-480
2015 Rogue NAM
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
Check refueling EVAP vapor cut valve. Refer to EC-482, "Component Inspection".
A
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) or FL-15, "AWD : Removal and Installation" (with AWD models). EC
CHECK EVAP CANISTER
7.
1.
Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached. Refer to FL-19, "Removal and Installation".
2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the inspection result normal?
YES >> GO TO 8.
NO
>> GO TO 9.
8.CHECK IF EVAP CANISTER IS SATURATED WITH WATER
Check if water will drain from EVAP canister.
Does water drain from the EVAP canister?
YES >> GO TO 6.
NO
>> GO TO 11.
JMBIA1134GB
9.REPLACE EVAP CANISTER
Replace EVAP canister with a new one. Refer to FL-19, "Removal and Installation".
>> GO TO 10.
10.DETECT MALFUNCTIONING PART
Check the EVAP hose between EVAP canister and vehicle frame for clogging or poor connection.
>> Repair or replace EVAP hose. Refer to FL-11, "FWD : Removal and Installation" (with FWD models) or FL-15, "AWD : Removal and Installation" (with AWD models).
11.CHECK VENT HOSES AND VENT TUBES
Check hoses and tubes between EVAP canister and refueling control valve for clogging, kinks, looseness and
improper connection.
Is the inspection result normal?
YES >> GO TO 12.
NO
>> Repair or replace hoses and tubes.
12.CHECK FILLER NECK TUBE
Check recirculation line for clogging, dents and cracks.
Is the inspection result normal?
YES >> GO TO 13.
NO
>> Replace filler neck tube.
13.CHECK REFUELING EVAP VAPOR CUT VALVE
Check refueling EVAP vapor cut valve. Refer to EC-482, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 14.
Revision: August 2014
EC-481
2015 Rogue NAM
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) FL-15, "AWD : Removal and Installation" (with AWD models).
14.CHECK FUEL FILLER TUBE
Check filler neck tube and hose connected to the fuel tank for clogging, dents and cracks.
Is the inspection result normal?
YES >> GO TO 15.
NO
>> Replace fuel filler tube. Refer to FL-11, "FWD : Exploded View" (with FWD models) FL-15, "AWD :
Exploded View" (with AWD models).
15.CHECK ONE-WAY FUEL VALVE-1
Check one-way valve for clogging.
Is the inspection result normal?
YES >> GO TO 16.
NO
>> Repair or replace one-way fuel valve with fuel tank. Refer to FL-11, "FWD : Removal and Installation" (with FWD models) FL-15, "AWD : Removal and Installation" (with AWD models).
16.CHECK ONE-WAY FUEL VALVE-2
1.
2.
Check that fuel is drained from the tank.
Remove fuel filler tube and hose. Refer to FL-11, "FWD : Exploded View" (with FWD models) FL-15,
"AWD : Exploded View" (with AWD models).
3. Check one-way fuel valve for operation as per the following.
When a stick is inserted, the valve should open, when removing
stick it should close.
Do not drop any material into the tank.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace fuel filler tube or replace one-way fuel valve
with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) FL-15, "AWD : Removal
and Installation" (with AWD models).
SEF665U
Component Inspection
INFOID:0000000011278199
1.INSPECTION START
Will CONSULT be used?
Will CONSULT be used?
YES >> GO TO 2.
NO
>> GO TO 3.
2.CHECK REFUELING EVAP VAPOR CUT VALVE
With CONSULT
Turn ignition switch OFF.
Remove fuel tank. Refer to FL-11, "FWD : Removal and Installation" (with FWD models) FL-15, "AWD :
Removal and Installation" (with AWD models).
3. Drain fuel from the tank as per the following:
Remove fuel feed hose located on the fuel gauge retainer.
Connect a spare fuel hose, one side to fuel gauge retainer where the hose was removed and the other
side to a fuel container.
Drain fuel using FUEL PUMP RELAY in ACTIVE TEST mode with CONSULT.
4. Check refueling EVAP vapor cut valve for being stuck to close as per the following.
Blow air into the refueling EVAP vapor cut valve (from the end of EVAP/ORVR line hose), and check that
the air flows freely into the tank.
5. Check refueling EVAP vapor cut valve for being stuck to open as per the following.
Connect vacuum pump to hose end.
Remove fuel gauge retainer with fuel gauge unit.
Always replace O-ring with new one.
Turn fuel tank upside down.
1.
2.
Revision: August 2014
EC-482
2015 Rogue NAM
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
-
Apply vacuum pressure to hose end [13.3 kPa (0.136 kg/cm2, 1.93 psi)] with fuel gauge retainer
remaining open and check that the pressure is applicable.
EC
JSBIA4497ZZ
Filler tube
Recirculation line
Vacuum/pressure handy pump
Fuel tank
EVAP/ORVR line
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) FL-15, "AWD : Removal and Installation" (with AWD models).
3.CHECK REFUELING EVAP VAPOR CUT VALVE
Without CONSULT
1. Turn ignition switch OFF.
2. Remove fuel tank. Refer to FL-11, "FWD : Removal and Installation" (with FWD models) FL-15, "AWD :
Removal and Installation" (with AWD models).
3. Drain fuel from the tank as per the following:
Remove fuel gauge retainer.
Drain fuel from the tank using a handy pump into a fuel container.
4. Check refueling EVAP vapor cut valve for being stuck to close as per the following.
Blow air into the refueling EVAP vapor cut valve (from the end of EVAP/ORVR line hose), and check that
the air flows freely into the tank.
5. Check refueling EVAP vapor cut valve for being stuck to open as per the following.
Connect vacuum pump to hose end.
Remove fuel gauge retainer with fuel gauge unit.
Always replace O-ring with new one.
Turn fuel tank upside down.
Apply vacuum pressure to hose end [13.3 kPa (0.136 kg/cm2, 1.93 psi)] with fuel gauge retainer
remaining open and check that the pressure is applicable.
Revision: August 2014
EC-483
2015 Rogue NAM
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
JSBIA4497ZZ
Filler tube
Recirculation line
Vacuum/pressure handy pump
Fuel tank
EVAP/ORVR line
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace refueling EVAP vapor cut valve with fuel tank. Refer to FL-11, "FWD : Removal and
Installation" (with FWD models) FL-15, "AWD : Removal and Installation" (with AWD models).
Revision: August 2014
EC-484
2015 Rogue NAM
REFRIGERANT PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
REFRIGERANT PRESSURE SENSOR
Component Function Check
A
INFOID:0000000011278200
1.CHECK REFRIGERANT PRESSURE SENSOR FUNCTION
1.
2.
3.
EC
Start engine and warm it up to normal operating temperature.
Turn A/C switch and blower fan switch ON.
Check the voltage between ECM harness connector terminals under the following conditions.
ECM
+
Connector
Voltage (V)
124
1.0 - 4.0
Terminal
E16
103
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Proceed to EC-485, "Diagnosis Procedure".
Diagnosis Procedure
F
INFOID:0000000011278201
1.CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY
1.
2.
3.
Disconnect refrigerant pressure sensor harness connector.
Turn ignition switch ON.
Check the voltage between refrigerant pressure sensor harness connector and ground.
+
-
Voltage
(Approx.)
Ground
5V
Refrigerant pressure sensor
Connector
Terminal
F10
Is the inspection result normal?
YES >> GO TO 3.
NO
>> GO TO 2.
2.CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.
+
Refrigerant pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F10
E16
104
Existed
3.CHECK REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.
Revision: August 2014
Is the inspection result normal?
YES >> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
1.
2.
3.
EC-485
2015 Rogue NAM
REFRIGERANT PRESSURE SENSOR
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
+
Refrigerant pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F10
E16
124
Existed
4. Also check harness for short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.
+
Refrigerant pressure sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
F10
E16
103
Existed
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES >> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-44, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace refrigerant pressure sensor. Refer to HAC-108, "Removal and Installation" (with automatic air conditioner) or HAC-184, "Removal and Installation" (with manual air conditioner).
NO
>> Repair or replace error-detected parts.
Revision: August 2014
EC-486
2015 Rogue NAM
SENSOR POWER SUPPLY2 CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
SENSOR POWER SUPPLY2 CIRCUIT
Description
INFOID:0000000011278202
ECM supplies a voltage of 5 V to some of the sensors systematically divided into 2 groups, respectively. EC
Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously
in the sensors belonging to the same group as the short-circuited sensor.
C
Sensor power supply 1
APP sensor 1
CKP sensor (POS)
Intake manifold runner control valve position sensor
Refrigerant pressure sensor
TP sensor
NOTE:
If sensor power supply 1 circuit is malfunctioning, DTC P0643 is displayed.
Sensor power supply 2
APP sensor 2
CMP sensor (PHASE)
EVT control position sensor
EOP sensor
MAF sensor
Diagnosis Procedure
INFOID:0000000011278203
1.CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-1
1.
2.
3.
4.
Turn ignition switch OFF.
Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.
+
-
Voltage
(Approx.)
Ground
5V
APP sensor
Connector
Terminal
E25
Is the inspection result normal?
YES >> INSPECTION END
NO
>> GO TO 2.
2.CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-2
1.
2.
3.
Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E25
E16
118
Existed
3.CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Disconnect following sensors harness connector.
Check harness for short to power and short to ground, between the following terminals.
Revision: August 2014
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair open circuit.
1.
2.
EC-487
2015 Rogue NAM
SENSOR POWER SUPPLY2 CIRCUIT
[QR25DE]
< DTC/CIRCUIT DIAGNOSIS >
ECM
Connector
F51
E16
Sensor
Terminal
Name
Connector
Terminal
32
CMP sensor (PHASE)
F44
36
MAF sensor
F22
40
EOP sensor
F54
44
EVT control position sensor
F45
118
APP sensor 2
E25
Is the inspection result normal?
YES >> GO TO 4.
NO
>> Repair short to ground or short to power in harness or connectors.
4.CHECK COMPONENTS
Check the following.
APP sensor 2 (Refer to EC-447, "Component Inspection".)
Camshaft position sensor (PHASE) (Refer to EC-303, "Component Inspection (Camshaft position sensor)".)
EVT control position sensor (Refer to EC-390, "Component Inspection".)
EOP sensor (Refer toEC-363, "Component Inspection".)
MAF sensor (Refer to EC-203, "Component Inspection".)
Is the inspection result normal?
YES >> Refer to GI-44, "Intermittent Incident".
NO
>> Replace malfunctioning component.
Revision: August 2014
EC-488
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
ENGINE CONTROL SYSTEM
Symptom Table
INFOID:0000000011278204
EC
SYSTEM BASIC ENGINE CONTROL SYSTEM
C
Fuel pressure regulator system
Fuel injector circuit
Air
AF
AG
AH
AJ
AK
AL
AM
HA
3
4
E
Reference
page
H
EC-470
EC-147
EC-467
EC-347,
EC-350
Fuel tank temperature sensor circuit
EC-275,
EC-277
Evaporative emission system
Positive crankcase ventilation system
EC-498
1
EC-144
2
EC-436,
EC-441
Incorrect ignition timing adjustment
EC-497
Ignition circuit
EC-473
EC-168
EC-501
Electric throttle control actuator
Main power supply and ground circuit
Fuel level sensor circuit
Incorrect idle speed adjustment
Ignition
BATTERY DEAD (UNDER CHARGE)
Fuel pump circuit
EXCESSIVE OIL CONSUMPTION
Fuel
EXCESSIVE FUEL CONSUMPTION
AE
OVERHEATS/WATER TEMPERATURE HIGH
LACK OF POWER/POOR ACCELERATION
AD
SLOW/NO RETURN TO IDLE
SPARK KNOCK/DETONATION
AC
IDLING VIBRATION
HESITATION/SURGING/FLAT SPOT
AB
ROUGH IDLE/HUNTING
ENGINE STALL
AA
Warranty symptom code
HIGH IDLE/LOW IDLE
HARD/NO START/RESTART (EXCP. HA)
SYMPTOM
Revision: August 2014
EC-489
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< SYMPTOM DIAGNOSIS >
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code
HARD/NO START/RESTART (EXCP. HA)
SYMPTOM
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
HA
EC-201,
EC-205
Mass air flow sensor circuit
2
Intake air temperature sensor circuit
Reference
page
EC-210,
EC-211
Engine coolant temperature sensor circuit
EC-216,
EC-222
Air fuel ratio (A/F) sensor 1 circuit
EC-229,
EC-233,
EC-236,
EC-258,
EC-429
Throttle position sensor circuit
EC-219,
EC-287,
EC-403,
EC-404,
EC-449
2
Accelerator pedal position sensor circuit
Heated oxygen sensor 2 circuit
Knock sensor circuit
Engine oil temperature sensor circuit
Engine oil pressure sensor circuit
EC-443,
EC-446,
EC-452
EC-239,
EC-247,
EC-254
EC-296
EC-282,
EC-284
EC-361,
EC-365
Crankshaft position sensor (POS) circuit
EC-298
Camshaft position sensor (PHASE) circuit
EC-301
Vehicle speed signal circuit
ECM
Intake valve timing control solenoid valve circuit
Revision: August 2014
EC-490
EC-353
EC-373,
EC-375,
EC-376,
EC-379,
EC-380,
EC-381
EC-180,
EC-194
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< SYMPTOM DIAGNOSIS >
SYMPTOM
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
HA
Intake valve timing intermediate lock control
solenoid valve circuit
Reference
page
PNP signal circuit
Refrigerant pressure sensor circuit
Electrical load signal circuit
EC-198
EC-385
EC-485
Intake manifold runner control valve motor circuit
Intake manifold runner control valve position
sensor circuit
EC-465
EC-367
Exhaust valve timing control solenoid valve
circuit
Air conditioner circuit
EC
EC-423
ASCD steering switch circuit
ABS actuator and electric unit (control unit)
EC-426
3
HAC-46,
HAC-147
EC-406
4
BRC-64
1 - 6: The numbers refer to the order of inspection.
(continued on next table)
SYSTEM ENGINE MECHANICAL & OTHER
Revision: August 2014
EC-491
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< SYMPTOM DIAGNOSIS >
Fuel
Fuel tank
Fuel piping
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
A
A
HESITATION/SURGING/FLAT SPOT
Warranty symptom code
ENGINE STALL
HARD/NO START/RESTART (EXCP. HA)
SYMPTOM
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
HA
FL-11, FL-15
Vapor lock
Reference page
EM-45
Valve deposit
Poor fuel (Heavy weight gasoline, Low octane)
Air
Air duct
Air cleaner
EM-26
Air leakage from air duct
(Mass air flow sensor electric throttle control actuator)
Electric throttle control actuator
5
5
5
5
EM-29
Air leakage from intake manifold/Collector/Gasket
Cranking
Battery
Generator circuit
Engine
PG-78
CHG-5
Starter circuit
Signal plate
EM-98
PNP signal
TM-220
Cylinder head
Cylinder head gasket
STR-6
EM-66
Cylinder block
4
Piston
Piston ring
Connecting rod
EM-98
Bearing
Crankshaft
Revision: August 2014
EC-492
2015 Rogue NAM
ENGINE CONTROL SYSTEM
[QR25DE]
< SYMPTOM DIAGNOSIS >
Valve
mechanism
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
A
A
HESITATION/SURGING/FLAT SPOT
Warranty symptom code
ENGINE STALL
HARD/NO START/RESTART (EXCP. HA)
SYMPTOM
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
HA
C
Reference page
Timing chain
EM-50
Camshaft
EM-69
Intake valve timing control
Exhaust valve
Exhaust manifold/Tube/Muffler/Gasket
EM-50
Intake valve
Exhaust
EC
EM-66
Cooling
Oil pan/Oil strainer/Oil pump/
Oil filter/Oil gallery/Oil cooler
I
5
EM-36, LU-7,
LU-10, LU-5,
LU-13
Oil level (Low)/Filthy oil
LU-7
Radiator/Hose/Radiator filler
cap
CO-13
Thermostat
Water pump
Water gallery
5
5
CO-21
4
Cooling fan
CO-19
CO-5
CO-17
5
Coolant level (Low)/Contaminated coolant
NVIS (NISSAN Vehicle Immobilizer System NATS)
EM-32, EX-5
Three way catalyst
Lubrication
CO-8
SEC-63, SEC156
1 - 6: The numbers refer to the order of inspection.
Revision: August 2014
EC-493
2015 Rogue NAM
INFORMATION DISPLAY IS MALFUNCTIONING
[QR25DE]
< SYMPTOM DIAGNOSIS >
INFORMATION DISPLAY IS MALFUNCTIONING
Diagnosis Procedure
INFOID:0000000011278205
1.CHECK DTC WITH ECM
Check that DTC is not displayed.
Is the inspection result normal?
YES >> GO TO 2.
NO
>> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK INFORMATION DISPLAY (ASCD)
Refer to EC-478, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.CHECK INTERMITTENT INCIDENT
Refer to GI-44, "Intermittent Incident".
>> INSPECTION END
Revision: August 2014
EC-494
2015 Rogue NAM
NORMAL OPERATING CONDITION
[QR25DE]
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
Description
A
INFOID:0000000011278206
FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED)
EC
If the engine speed is above 1,800 rpm under no load (for example, the selector lever position is neutral and
engine speed is over 1,800 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off varies based on engine speed.
Fuel cut will be operated until the engine speed reaches 1,500 rpm, then fuel cut will be cancelled.
NOTE:
This function is different from deceleration control listed under Multiport Fuel Injection (MFI) System, EC-37,
"MULTIPORT FUEL INJECTION SYSTEM : System Description (with automatic air conditioner)" or EC-39,
"MULTIPORT FUEL INJECTION SYSTEM : System Description (with manual air conditioner)".
Revision: August 2014
EC-495
2015 Rogue NAM
IDLE SPEED
[QR25DE]
< PERIODIC MAINTENANCE >
PERIODIC MAINTENANCE
IDLE SPEED
Inspection
INFOID:0000000011278207
1.CHECK IDLE SPEED
With CONSULT
Check idle speed in DATA MONITOR mode of ENGINE using CONSULT.
With GST
Check idle speed with Service $01 of GST.
>> INSPECTION END
Revision: August 2014
EC-496
2015 Rogue NAM
IGNITION TIMING
[QR25DE]
< PERIODIC MAINTENANCE >
IGNITION TIMING
Inspection
INFOID:0000000011278208
1.CHECK IGNITION TIMING
1.
EC
Attach timing light (A) to the ignition coil No.1 harness
.
C
E
ALBIA1182ZZ
2.
Check ignition timing.
: Timing indicator
>> INSPECTION END
H
JPBIA5854ZZ
Revision: August 2014
EC-497
2015 Rogue NAM
EVAPORATIVE EMISSION SYSTEM
[QR25DE]
< PERIODIC MAINTENANCE >
EVAPORATIVE EMISSION SYSTEM
Inspection
INFOID:0000000011278209
EVAP CANISTER
1.CHECK EVAP CANISTER
1.
2.
3.
4.
5.
6.
Block port (B).
Blow air into port (A) and check that it flows freely out of port (C).
Release blocked port (B).
Apply vacuum pressure to port (B) and check that vacuum pressure exists at the ports (A) and (C).
Block port (A) and (B).
Apply pressure to port (C) and check that there is no leakage.
>> INSPECTION END
PBIB1212E
Revision: August 2014
EC-498
2015 Rogue NAM
EVAP LEAK CHECK
[QR25DE]
< PERIODIC MAINTENANCE >
EVAP LEAK CHECK
Inspection
INFOID:0000000011278210
CAUTION:
EC
Do not use compressed air or a high pressure pump.
Do not exceed 4.12 kPa (0.042 kg/cm2, 0.6 psi) of pressure in EVAP system.
NOTE:
C
Do not start engine.
Improper installation of EVAP service port adapter [commercial service tool: (J-41413-OBD)] to the EVAP
service port may cause a leak.
D
EVAP LEAK CHECK
1.
1.
With CONSULT
Install EVAP service port adapter [commercial service tool: (J41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
2.
3.
4.
5.
6.
7.
Turn ignition switch ON.
Select the EVAP SYSTEM CLOSE in WORK SUPPORT mode of ENGINE using CONSULT.
Touch START. A bar graph (Pressure indicating display) will appear on the screen.
Apply positive pressure to the EVAP system until the pressure indicator reaches the middle of the bar
graph.
Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
Locate the leak using a leak detector [commercial service tool:
(J-41416)]. Refer to EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description".
M
SEF200U
1.
Without CONSULT
Install EVAP service port adapter [commercial service tool: (J41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
Revision: August 2014
EC-499
2015 Rogue NAM
EVAP LEAK CHECK
[QR25DE]
< PERIODIC MAINTENANCE >
2. Apply battery voltage between the terminals of EVAP canister vent control valve to make a closed EVAP
system.
3. To locate the leak, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to
2.76 kPa (0.014 to 0.028 kg/cm2, 0.2 to 0.4 psi).
4. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
5. Locate the leak using a leak detector [commercial service tool:
(J-41416)]. Refer to EC-55, "EVAPORATIVE EMISSION SYSTEM : System Description".
>> INSPECTION END
SEF200U
Revision: August 2014
EC-500
2015 Rogue NAM
POSITIVE CRANKCASE VENTILATION
[QR25DE]
< PERIODIC MAINTENANCE >
POSITIVE CRANKCASE VENTILATION
Inspection
A
INFOID:0000000011278211
1.CHECK PCV VALVE
EC
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES >> INSPECTION END
NO
>> Replace
PCV
valve.
Refer
to
EC-14,
"Component Parts Location".
E
PBIB1589E
Revision: August 2014
EC-501
2015 Rogue NAM
ECM
[QR25DE]
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
ECM
Removal and Installation
INFOID:0000000011278212
EXPLODED VIEW
ALBIA1179ZZ
ECM bracket
ECM
: Vehicle front
CAUTION:
Perform ADDITIONAL SERVICE WHEN REPLACING ECM. Refer to EC-139, "Work Procedure".
REMOVAL
1.
2.
3.
4.
5.
Disconnect the battery negative terminal.
Remove the air inlet duct. Refer to EM-26, "Removal and Installation".
Remove the resonator. Refer to EM-26, "Exploded View".
Disconnect ECM harness connectors.
Remove ECM mounting nuts, and then remove ECM.
INSTALLATION
Install in the reverse order of removal.
Revision: August 2014
EC-502
2015 Rogue NAM
SERVICE DATA AND SPECIFICATIONS (SDS)
[QR25DE]
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Idle Speed
INFOID:0000000011278213
Condition
Specification
650 50 rpm
No load* (in P or N position)
EC
*: Under the following conditions
A/C switch: OFF
Electric load: OFF (Lights, heater fan & rear window defogger)
Steering wheel: Kept in straight-ahead position
Ignition Timing
INFOID:0000000011278214
Condition
Specification
10 2 BTDC
No load* (in P or N position)
*: Under the following conditions
A/C switch: OFF
Electric load: OFF (Lights, heater fan & rear window defogger)
Steering wheel: Kept in straight-ahead position
Calculated Load Value
INFOID:0000000011278215
Condition
Specification (Using CONSULT or GST)
At idle
10 35 %
At 2,500 rpm
10 35 %
Mass Air Flow Sensor
INFOID:0000000011278216
K
Supply voltage
Battery voltage (11 14 V)
Output voltage at idle
1.3 1.6 V*
1.0 4.0 g/s at idle*
4.0 10.0 g/s at 2,500 rpm*
Mass air flow (Using CONSULT or GST)
*: Engine is warmed up to normal operating temperature and running under no load.
Revision: August 2014
EC-503
