Foxboro Evo
Process Automation
System
Product Specifications
PSS 31H-8K3
Foxboro Evo SCD6000 Wide Range Input Power Supply Module
INTRODUCTION
FEATURES
The Wide Range Input Power Supply module is used
with larger SCD6000 and SCD5200 configurations
(more than five input output or communications
modules). The integrated power supply of the COPE
module is used in other configurations. Refer to PSS
31H-8K2.
Input supply: 19.2V to 148V DC positive or
Located in the first slot of the file, the Power Supply
module accommodates a fully populated ten I/O file.
The input supply is connected to this module only.
The COPE module power supply is not used in ten
I/O file configurations.
SCD system failure alarm LED and contact
negative earth
Meet the demands of a ten I/O file
Withstands 4 ms dead shorted supply input
Over-current and over/under voltage protection
Control supply isolation terminals
Loop power distribution terminals
Power supply OK and Fail LEDs.
PSS 31H-8K3
Page 2
FUNCTIONAL DESCRIPTION
The module provides the regulated +5 V dc, +15 V
dc, and -15 V dc operating supplies for a ten I/O file.
A 1.000 V dc supply is provided as a reference for
the internal checking of analog input modules.
A switched mode design provides operation over a
wide dc input range from 19.2V to 148V, provides
high input to output isolation, and minimizes size to
weight ratio, while offering high power conversion
efficiency and high reliability.
Internal monitoring provides a system reset to the
RTU modules if the +5 V supply is abnormal. A front
panel INPUT OK LED indicates the supply is normal.
Electrobus Interface
Monitors and
Indicators
Power Supply
Analog Input
Check Voltage
(+1 v)
SysFail Relay
Driver
DC Input
Input Terminal
Surge Suppression
and Filter
Output Relay and
LED Indicator
Switch and Fuse
Terminals
Figure 1. Power Supply Module Functional Block Diagram
The 15 V rails are monitored and the status is
indicated by the 15 V OK LED on the front panel. A
relay contact (normal open and normal closed),
controlled by the system fail and 15 V rail fault, is
available on the front panel terminals.
PSS 31H-8K3
Page 3
Figure 2. Ten I/O File Power Supply System for SCD5200, Example Implementation
The module provides contacts for an external
warning lamp or audible alarm to indicate an SCD
fault or 15 V rails fault.
To isolate the control supply, wire an external switch
or relay to the controls isolate terminals of the
module.
Module Description
Each ten I/O card file has a removable Power Supply
module (see Figure 2). Future expansion within the
ten I/O file does not require any power supply
changes because the larger card file has a dedicated
power supply sized to accommodate a fully
equipped file. The power supply is always correctly
sized regardless of the I/O in the ten I/O file.
Front Panel
The Wide Range Input Power Supply module is
always located in the first slot of the ten I/O file. (See
Figure 2).
The module plugs into a backplane (Electrobus) via a
DIN 41612 connector and is double Eurocard size.
The modules can be supplied using a 24, 48, or 129
V dc nominal power source.
The module provides contacts for an external
warning lamp or audible alarm to indicate an RTU or
15 V fault.
You can isolate the control supply by affixing an
external switch or relay.
A pair of terminals are connected to a remote facility
for isolating supply to control outputs.
A front panel power switch is provided.
PSS 31H-8K3
Page 4
OFF
ON
POWER
IN
LOOP
POWER
NC
C ALARM
NO
CONTROL
ISOLATE
INPUT OK
15 V OK
LED's
Figure 3. Front Panel
E L E CT R I C A L S P E C I F I C AT I O N S
Power Requirements
Under-Voltage Protection
90 W maximum input
Shutdown at low input voltage
Input Voltage
Hold-up Time
Wide range input voltage 19.2V to 148V DC
Withstands 4 ms dead shorted power supply input
Output Capability
Ripple and Noise
+5 V at 9 A
+15 V at 1 A
15 V at 0.35 A
Maximum output of 65 watts total permitted
50 mV peak-peak (+5 V)
100 mV peak-peak (15 V)
Input Current
4.7 A maximum at 19.2V
0.60 A maximum at 148V
Efficiency
>70% at full load with nominal input voltage
Current Limit
Shutdown at maximum power with auto-recovery
Over-Voltage Protection
Crowbar protection set at 6.25 V
Isolation
2000 V ac RMS for 1 minute
Primary-to-Chassis and Primary-to-Secondary
isolation
Transient Protection
IEC 255-4 class 3 (5 kV impulse, 2.5 kV HFD)
ANSI IEEE C37.90.1 (as above)
IEC 61000-4-4 Level 3 (2 kV)
IEC 61000-4-5 Level 3 (2 kV)
EMC Conducted Noise
EN50011 Class B
PSS 31H-8K3
Page 5
E L E C T R I C A L S P E C I F I C AT I O N S ( C O N T I N U E D )
Fail Alarm Output
LED Indications
Relay output contact to terminals controlled by
Electrobus SYSFAIL signal and 15 V rail fault.
Input voltage OK, 15 V within limits
On Board Fuse
10A/250 V Type T, 20 x 5 mm
E N V I R O N M E N TA L S P E C I F I C AT I O N S
Operating Temperature
Cooling
0C to 60C (32F to 140F)
Natural convection, no forced cooling required.
Humidity
10% to 95% (noncondensing)
P R OD U CT S AF E T Y
This product complies with the U.S. Standard for
Safety UL 61010-1 - Safety requirements for
Electrical equipment for measurement, control, and
laboratory use - PART 1: GENERAL REQUIREMENTS
- Edition 2 - Revision Date 2008/10/28 and CSA
C22.2 NO. 61010-1 - Safety requirements for
Electrical equipment for measurement, control, and
laboratory use.
P H Y S I C A L S PE CI F I C AT I O N S
Physical Size
The module requires frame space of 35.56 mm.
The module is double Eurocard size (233.4 mm x 160
mm board, 261.8 x 182 x 35.3 mm module.
OR D E R I N G I N F O RM AT I O N
Part Number
SY-0399131
Description
Wide Input Range Power Supply Module
PSS 31H-8K3
Page 6
PSS 31H-8K3
Page 7
PSS 31H-8K3
Page 8
Invensys Systems, Inc
10900 Equity Drive
Houston, TX 77041
United States of America
http://www.invensys.com
Global Customer Support
Inside U.S.: 1-866-746-6477
Outside U.S.: 1-508-549-2424
Website: https://support.ips.invensys.com
Copyright 2015 Invensys Systems, Inc.
All rights reserved.
Invensys is now part of Schneider Electric.
Schneider Electric, Invensys, Foxboro, Foxboro Evo,
FoxCom, and I/A Series, are trademarks owned by
Schneider Electric SE, its subsidiaries and affiliates.
All other trademarks are the property of their respective
owners.
MB 031
0315
