Scribd
Upload
117 views

Ekm 25ids Spec Sheet

This document provides specifications and installation instructions for the EKM-25IDS single phase kWh meter from eKM Metering Inc. The meter measures electricity consumption up to 100 amps with an accuracy of 1% and outputs 800 pulses per kWh. It is intended for indoor use but can be installed outdoors if housed in a protective enclosure. Installation involves passing the power lines through the meter housing and mounting it on DIN rail while ensuring safety precautions are followed like verifying power is off before handling.

Uploaded by

Adam Brouwer
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
117 views

Ekm 25ids Spec Sheet

This document provides specifications and installation instructions for the EKM-25IDS single phase kWh meter from eKM Metering Inc. The meter measures electricity consumption up to 100 amps with an accuracy of 1% and outputs 800 pulses per kWh. It is intended for indoor use but can be installed outdoors if housed in a protective enclosure. Installation involves passing the power lines through the meter housing and mounting it on DIN rail while ensuring safety precautions are followed like verifying power is off before handling.

Uploaded by

Adam Brouwer
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

eKM Metering Inc.

EKM-25IDS Spec Sheet

178

11
100

65 .

(Fig 1)

Technical Specifications:
120/240V Single Phase, pass-through kWh meter
Rated Voltage: 120/240 volts
Rated current: 5(100)A
Works with wires up to 3/8 in diameter
Pulse output impulse constant: 800imp/kWh
Range of allowable environmental conditions: Pollution Degree 2,
Measurement Category III, Altitude rating 2000 meters max. Maximum
Temperature Range: -30 Deg. C to 70 Deg. C.
The equipment is protected throughout by
double insulation as indicated by this symbol:
Accuracy Class: 1 (Fig 3)
Rated Frequency: 50Hz/60Hz
Creep: Logical design of anti-creep
Start current: 0.4% Ib. (1.0)
Power consumption: 1W (when 220V, 20A)
Tamper Detection Class 1.
Weight: 0.32kg
Outside dimensions: 78x100x65mm (Fig 1)
Safety Precautions:
Meter should be installed by a qualified electrician.
Turn o all power supplying the equipment before preforming any
installation or service. Use a volt meter to confirm power is o.
Use of this device inconsistent with this manual can cause permanent
damage to the unit and/or serious harm to the installer or operator.
Tools/Materials List:
Volt meter
Small standard screwdriver
DIN-Rail
UL Listed Type 4 Enclosure (with appropriately rated conduit and
fittings) is required if meter will be installed outdoors
Functions:
Long-term active electricity measuring without adjustment.
Meets IEC 62053-21 and IEC 62052-11 standards (static AC active meter)

Installation Instructions:
1. Use a volt meter to confirm that you have 240 volts between L1 and L2.
This meter will not function correctly unless this is the case. For 120V
systems, use our EKM-15IDS v.2, EKM-15E, or any Omnimeter model.
2. Disconnect or switch power o before attempting to install, connect,
disconnect, or service the meter. ALL POWER MUST BE TURNED OFF!
3. IMPORTANT: Distinguish and then identify the 2 hot Lines and the
neutral line. Label all 3: L1, L2, N.
4. Once the power has been turned o, pass line 1 and line 2 through the
two holes in the meter. (for a retrofit installation this may first require
disconnecting the ends of L1 and L2 from a breaker or junction box)
5. Once the wires are through the meter, the ends should be reconnected
in their original positions. On the meter, tighten down the tap screws
for each line that passes through the meter. The tap screws penetrate
the wire insulation and power the meter once the power is turned on.
6. Mount the meter using 35mm DIN Rail in a protected indoor location.
If installing outdoors, a UL Listed Type 4 Enclosure is required.
7. Once the above steps are completed, and you are ready, you can turn
the power back on and begin to read your meter.
SO

+ _

1 2 3 4 5 6

(Fig 2)

Pulse Output(Fig 2):


Terminals 1 and 2 are for pulse output. Pulse rate: 800 Impulse/kWh.
Polarity sensitive. Maximum 27VDC, 27mA.
Red LED on the meter face flashes 800 times/kWh. 1 flash = 1.25Wh.
Load
current
0.05Ib
0.1Ib~Imax
0.1Ib
0.2Ib~Imax

Power
factor
COS
1.0
1.0
0.5(L)
0.8(C)
0.5(L)
0.8(C)

Basic error %
Class 0.5

Class 1

Class 2

+
1.0
+
0.5
+
1.0
+
1.0
+
0.5
+
0.5

+
1.5
+
1.0
+
1.5
+
1.5
+
1.0
+
1.0

+
2.5
+
2.0
+
2.5
--+
2.0
---

(Fig 3)

EKM Metering Inc. www.ekmmetering.com [email protected] (831)425-7371

eKM Metering Inc.


Working Principle:
When the meter is working, the energy consumed by the user is transformed into voltage and current signals, which are sampled by sample circuits. A
pulse signal is then produced by a specialized IC. The Pulse signal is directly proportional to power consumption. The MCU records and stores the
corresponding energy use. The LCD screen displays the energy use.
Data:
The LCD display shows one piece of data: total electricity consumed(kWh). By design the kWh cannot be reset. The meter will go at least 10 years
without power and still keep its kWh readings. In other words, the memory will not be erased if there is no power.
Transport and Handling:
The meter should be handled with care, as there are precision components inside that could break and/or cause faulty readings should the meter
become damaged. The process of transportation, handling, and installation should be done according to the transportation and storage rule of
GB/T15464-1995. Keep the meter in the original packaging when stored. The storage temperature range should be 040C. The relative humidity
should be 85%. There should be no toxic chemicals present and no corrosive substances or gases in the air. The meters should be stacked on a
platform no more than ten units high.
Warranty:
Within two years from the date of sale, and on the condition that the user abide by the specifications and installation instructions listed here, and the
sealing is kept completely intact. If the meter does not correspond with the rule of the enterprise standard, the meter shall be repaired free or replaced.
Wiring Diagram:
The diagram shown below is also marked on the meter body.

120V
120V
240V

L1
1
2
3
4
5
6

L2

L1
+

SO

L2

(Fig 4)

EKM Metering Inc. www.ekmmetering.com [email protected] (831)425-7371

You might also like